Parts list (pattern): Ten A4 sheets (No. 1 to No. 10)No. of Parts: 77

Build this model with careful reference to the Assembly Instructions.

Editor:

View of completed model * This model was designed for Papercraft and may differ from the original in some respects.

Special Vehicle Series : 03

PatternBulldozerBulldozer

Blade capacity :

Overall length :

Overall width (main body) :

Overall height :

9.4 m

8,225 mm

2,700 mm

3,395 mm

A bulldozer is a construction vehicle that can use its front blade to level ground or its rear ripper to scrape earth and sand and to break up rocks. Categorized as a large bulldozer, the D155AX-6 is used in projects such as civil engineering works and quarry-ing sites. While a traditional bulldozer blade has a gently curved surface, the SIGMADOZER developed for this model has a profile that resembles the Greek letter sigma when viewed from above. Since it excavates from the central area of the blade, the D155AX-6 is more efficient than other bulldozers.

3

* If you prefer that the rear sides of the paper parts not be white, print the two optional reverse-side printing sheets on thin paper such as standard printer paper and adhere these to the reverse sides of sheets No. 8 to No. 10 using spray adhesive, then build the model as described in the instructions.

1/43 scale

PatternBulldozer

PatternBulldozer

PatternBulldozer

http

://ww

w.ca

no

n.co

m/c-p

ark/e

n/

© K

eisu

ke S

aka

Do not hit other people w

ith the pointed edges.D

oing so could result in injury. Adults should

make sure that children observe this caution.

CA

UT

ION

PatternBulldozer

PatternBulldozer

PatternBulldozer

PatternBulldozer

PatternBulldozer

PatternBulldozer

BulldozerBulldozerSpecial Vehicle Series

Special Vehicle Series : 03

Assembly InstructionsBulldozerBulldozerhttp://www.canon.com/c-park/en/

* This model was designed for Papercraft and may differ from the original in some respects.

View of completed model

Toolsools Assembly tipssembly tip

Key to symbolsKey to symbols

ScissorsRuler, set squareGlue (Wood glue or craft glue recommend)Exhausted ballpoint pen (out of ink)Toothpicks (for use in applying glue)Tweezers (useful for handling small parts)Pencil

Pattern

Red dot

Green dot

Blue dot

Assembly instructions

Solid line

Dashed and dotted line

Dotted line

Solid red line

Diagonalgrey lines

Mountain foldFold so that the printed pattern faces outside.

Fold so that the printed pattern faces inside.

Valley fold

Cut parts out along this line.

Cut a notch along this line.

Cut these areas out.

Glue parts with the same number together. (Numbers are not printed on very small parts.)

Glue areas within the same part together.

Glue

Insert

Glue tab

Reverse side of paper

(without gluing)

Red arrow

Blue arrow

Light blue

Light grey

Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children.

Assembly Instructions: Nine A4 sheets (No. 1 to No. 9)Build this model with careful reference to the Assembly Instructions.

Write the number of each part on the reverse side of the part in pencilupon cutting it out, to be sure you can tell which part is which later.Before gluing, crease the paper along mountain and valley fold lines. Trace along the folds with a ruler and an exhausted ballpoint pen (out of ink) to get a sharper fold. Make sure rounded sections are nice and stiff.

Glue to the reverse side of the specified part.

The dots show where to glue the pieces together. Glue the pieces together as shown in the following examples.Some parts must be glued together along the cut surfaces.

This denotes a part that must be able to move after the model is completed.Be sure to crease these parts sufficiently.

Movable part

Assembly InstructionsBulldozer

Assemble the cab. Glue flaps a, b, c, and d in order.

Glue flaps a, b, c, and d in order.

Glue flaps a, b, c, and d in order.

Assembly InstructionsBulldozer

Before assembly, cut out these tabs and fold them using valley folds.

Don’t forget to cut this notch out before assembly.

Glue flaps a, b, and c in order.

Insert the convex tab.

Glue this piece in place after first positioning it by matching the arrows to the corners.

Use care when gluing these pieces in place, to ensure that the bottom is level.

Assembly InstructionsBulldozer

Glue flaps a and b in order.

Inside

Inside

Outside Inside

Outside

Outside

Cross section

InsideOutside

InsideOutside

Cross section

Inside Outside

Cross section Cross section

Wrap part 64 around part 62 so the seam is on the bottom, and glue it in place.Make sure part 64 extrudes toward the outside.

Wrap part 65 around part 63 so the seam is on the bottom, and glue it in place.Make sure part 65 extrudes toward the outside.

Assemble the other side in the same way (making the left and right sides symmetrical).

Assembly InstructionsBulldozer

Refer to the cross-section when assembling parts 22 and 29.

Cross section

Cross section

Cross section

Movable part

Assemble the other side in the same way (making the left and right sides symmetrical).

This assembly does not include any parts corresponding to part in assembly .

Curving the parts on the inside, glue parts 66, 67, 68, 69, and 70 in position one spot at a time.

Aligning the bottom edges, glue these parts in place in order, starting from the center, and then finish this assembly by gluing the top edge in place.

Assembly InstructionsBulldozer

Cross section

Movable part

Make sure the arrows on part 37 are pointing up and glue parts 44, 45, and 46 in place, checking that each is positioned correctly.

Apply glue to the cutout areas of the paper and attach to part 37 in a way that hides the glue spots.

Assembly InstructionsBulldozer

Check the part position and glue in place.

Cross section

Check the part position and glue in place.

Cross section

Assembly InstructionsBulldozer

Slightly spread out the arms that connect to the sides of the main body and then insert them into the holes on both sides.

Cross section

Check the part position and glue in place.

On parts with no glue tabs, apply glue to the cut surface of the paper and glue this part to the body of the Bulldozer, concealing the glue tabs.(Refer to the photograph of the completed model.)

Finished!Last, assemble the nameplate and display it together with your model.

Bulldozer

Bulldozer

Special Vehicle Series

Assembly InstructionsBulldozer

Bulldozer Optional reverse-side printing sheet (yellow)

Print this sheet on thin paper such as standard printer paper and adhere it to the reverse side of sheet no. 8 using spray adhesive, then build the model as described in the instructions. There's no need to worry about which end of this sheet points up and which points down.

Bulldozer Optional reverse-side printing sheet (yellow)

Print this sheet on thin paper such as standard printer paper and adhere it to the reverse side of sheet no. 9 using spray adhesive, then build the model as described in the instructions. There's no need to worry about which end of this sheet points up and which points down.

Bulldozer Optional reverse-side printing sheet (yellow)

Print this sheet on thin paper such as standard printer paper and adhere it to the reverse side of sheet no. 10 using spray adhesive, then build the model as described in the instructions. There's no need to worry about which end of this sheet points up and which points down.