80
;;^d;‘;r; 1987 FUEL INJECTION SYSTEM 119 1 r U. w Ui I ““I RR1752E FUEL INJECTION - Circuit Diagram 1. 40 way connector to Electronic Control Unit (ECU). 2. Lambda sensor (left side - bank A). 3. Lambda sensor (right side - bank 8). 4. By-pass air valve (stepper motor) (fast idle). 5. Lambda sensor screened ground. 6. Fuse 18 - main fuse panel. 7. Inertia switch. 8. Fuel pump. 9. Ignition switch. 10. Speed transducer (road speed input). 7 1. Neutral switch (automatic gearbox) (load input). 12. Pick-up point-air conditioning circuit (load input). 13. Battery. 14. Diagnostic plug. 15. In-line resistor. 16. Coil/-ve (engine RPM input). 17. Coolant temperature thermistor (sensor) (input). 18. Fuel temperature thermistor (sensor) (input). 19. Throttle potentiometer. 20. Air flow sensor. 21. Fuel pump relay. 22. Main relay. 23. Injectors-l to 8. 24. Pick-up point E.F.I. warninasymbol (instrument binnacle). = = = Denotes screened ground. NOTE: Reference to left and right side is made when viewing vehicle from rear. Cable colour code B Black G Green R Red U Blue 0 Orange M’ White N Brown P Purple Y Yellow The last letter of a colour code denotes the tracer. REVISED: JULY 88 S Crey K Pink LG Light green 1 :, :. :;

14cux Fuel Injection

Embed Size (px)

DESCRIPTION

manual de inyeccion tipo 14cux, montada en range rover v8 con motor 3.5 y 3.9 efi.

Citation preview

Page 1: 14cux Fuel Injection

;;^d;‘;r; 1987 FUEL INJECTION SYSTEM 119 1

r U.w

Ui I ““IRR1752E

FUEL INJECTION - Circuit Diagram

1. 40 way connector to Electronic Control Unit(ECU).

2. Lambda sensor (left side - bank A).3. Lambda sensor (right side - bank 8).4. By-pass air valve (stepper motor) (fast idle).5. Lambda sensor screened ground.6. Fuse 18 - main fuse panel.7. Inertia switch.8. Fuel pump.9. Ignition switch.

10. Speed transducer (road speed input).7 1. Neutral switch (automatic gearbox) (load

input).12. Pick-up point-air conditioning circuit (load

input).

13. Battery.14. Diagnostic plug.15. In-line resistor.16. Coil/-ve (engine RPM input).17. Coolant temperature thermistor (sensor)

(input).18. Fuel temperature thermistor (sensor) (input).19. Throttle potentiometer.20. Air flow sensor.21. Fuel pump relay.22. Main relay.23. Injectors-l to 8.24. Pick-up point E.F.I. warninasymbol (instrument

binnacle).= = = Denotes screened ground.

NOTE: Reference to left and right side is made when viewing vehicle from rear.

Cable colour code

B Black G Green R Red

U Blue 0 Orange M’ WhiteN Brown P Purple Y Yellow

The last letter of a colour code denotes the tracer.REVISED: JULY 88

S CreyK PinkLG Light green

1 :,:.:;

Page 2: 14cux Fuel Injection

l-l19 FUEL INJECTION SYSTEM 1987 rot;;

‘,

‘, ., ,. :

ECU AND RELAY8

F W L RCOULATOR41 RCA1 OF ENOINE

FUEL WYP111 FUEL TANAUNDER RIGHT FRONTOEAT F:lJEL FILTER ON CHAlllll#1

L

a lNJcc10nsFOR ENONE

ROAO OFEED WUtTIIANOOUCER

I ON CNAIOW

COOLANT tEYPERATU(IEl LNIOR FRONT OF ENOM

FUEL TEYFEIIATUREl EN10R

liNOiNE FULL RAIL

A1111 IV’cA1I VALVEREAR OF ENOWE BAV

I

A-

R I HOT WIG ARFLOW8ENaoR FRONT LEFTl EIE OF LNONE l AV

\ .:-.

P

‘i..J /

,.. .

!

TWROTTLE FOTENTIOYETEFRONT OF

THROTTLE VALVElONRlON COL

LEFT IDE OF ENWIE l AV

RR2178E

2 REVISED: JULY 88

Page 3: 14cux Fuel Injection

ggf;i 1 9 8 7 FUEL INJECTION SYSTEM 119 1

INTRODUCTION

The Electronic Fuel injection system provides areliable and efficient microprocessor controlled fuelmanagement system.

The function of the system is to supply the exactamount of fuel directly into the inlet manifoldaccording to the prevailing engine operatingconditions.

To monitor these conditions, various sensors arefitted to the engine to measure engine parameters.Data from the sensors is received by the ElectronicControl Unit (E.C.U.), the E.C.U. will thendetermine the exact amount of fuel required at anycondition.

The E.C.U. having received data from the sensorsproduces pulses, the length of which will determinethe simultaneous open time of each bank ofinjectors in turn, which will govern the amount offuel injected.

DESCRIPTION

ELECTRONIC CONTROL UNIT-ECU

The Electronic Fuel Injection system is controlled bythe E.C.U. which is located under the front righthand seat. The control unit is a microprocessor withintegrated circuits and components mounted onprinted circuit boards. The E.C.U. is connected tothe main harness by a 40 pin plug.

INJECTORS

The eight fuel injectors are fitted between thepressurized fuel rail and inlet manifold. Each injectorcomprises a solenoid operated needle valve with amovable plunger rigidly attached to the nozzlevalve. When the solenoid is energized the plungeris attracted off its seat and allows pressurized fuelinto the intake manifold.

ENGINE COOLANT TEMPERATURE THERMISTOR(SENSOR)

The coolant thermistor (sensor) is located by thefront left hand branch of the intake manifold. Thethermistor provides engine coolant information tothe E.C.U. The E.C.U. on receiving the signal fromthe thermistor will lengthen slightly the time thatthe injectors are open, and reducing this time asthe engine reaches normal operating temperature.

FUEL TEMPERATURE THERMISTOR (SENSOR)

The fuel temperature thermistor (sensor) is locatedin the fuel rail forward of the ram housing. Thethermistor sends fuel temperature data to theE.C.U, the E.C.U on receiving the data will adjustthe injector open time accordingly to producegood hot starting in high ambient temperatures.

BYPASS AIR VALVE (STEPPER MOTOR)

The bypass valve is screwed into a housing attachedto the rear of the plenum chamber, between theplenum chamber and bulkhead. The bypass valvehas two windings which enable the motor to beenergised in both directions thus opening orclosing the air valve as required by the E.C.U.The bypass valve will open and allow extra air intothe plenum chamber to maintain engine idle speedwhen the engine is under increased (Electrical andMechanical) loads.The bypass valve will control engine idle speedwhen the vehicle is stationary.

LAMBDA SENSORS (0, SENSORS)

The two Lambda sensors are located fonvard of thecatalysts mounted in the exhaust downpipes.The sensors monitor the oxygen content of theexhaust gases and provide feedback information ofthe air/fuel ratio to the E.C.U. Each sensor is heatedby an electrical element to improve its responsetime when the ignition is switched on.

Continued

REVISED: APR. 87 3

Page 4: 14cux Fuel Injection

FUEL INJECTION SYSTEM 1987 rGv;;

FUEL PRESSURE REGULATOR THROlTLE POTENTIOMETER

The fuel pressure regulator is mounted in the fuelra i l at the rear o f the p lenum chamber . Theregulator is a mechanical device controlled byplenum chamber vacuum, it ensures that fuel railpressure is maintained at a constant pressuredifference of 2.5 bar above that of the manifold.When pressure exceeds the regulator setting excessfuel is returned to the fuel tank.

FUEL PUMP

The electric fuel pump is located in the fuel tank,and is a self priming ‘wet’ pump, the motor isimmersed in the fuel within the tank.

AIR FLOW SENSOR

The hot-wire air f low sensor is mounted on abracket attached to the left hand valance, rigidlyconnected to the air cleaner and by hose to theplenum chamber inlet neck.The air flow sensor consists of a cast alloy bodythrough which air flows. A proportion of this airflows through a bypass in which two wire elementsare situated: one is a sensing wire and the other isa compensating wire. Under the control of anelectronic module which is mounted on the air flowsensor body, a small current is passed through thesensing wire to produce a heating effect. Thecompensating wire is also connected to the modulebut is not heated, but reacts to the temperature ofthe air taken in, as engine intake air passes over thewires a cooling effect takes place.

The throttle potentiometer is mounted on the sideof the plenum chamber inlet neck and is directlycoupled to the throttle valve shaft.The potentiometer is a resistive device suppliedwith a voltage from the E.C.U. Movement of thethrottle pedal causes the throttle valve to open,thus rotating the wiper arm within thepotentiometer which in turn varies the resistance inpropor t ion to the valve pos i t ion . The E .C.U.lengthens the injector open time when it detects achange in output vo l tage ( r i s ing) f rom thepotentiometer.In addit ion the E.C.U. wil l weaken the mixturewhen it detects the potentiometer output voltage isdecreasing under deceleration and will shorten thelength of time the injectors are open.When the thrott le is ful ly open, the E.C.U. wil ldetect the corresponding throttle potentiometervoltage and will apply full load enrichment. This is afixed percentage and is independent o ftemperature. Full load enrichment is also achievedby adjusting the length of the injector open time.When the throttle is closed, overrun fuel cut off oridle speed control may be facilitated dependant onother inputs to the E.C.U.

ROAD SPEED TRANSDUCER

The electronic module monitors the reaction of thewires in proportion to the air stream and providesoutput signals in proportion to the air mass flowrate which are compatible with the requirements ofthe E.C.U.

The road speed transducer is fitted between theupper and lower speedometer cables. It is mountedon a bracket located on the left hand chassis sidemember adjacent to the rear engine mounting. Thetransducer provides road speed data to the ECU.The ECU in turn detects vehicle movement fromthe road speed input and ensures that idle speedcontrol mode is disengaged. Should the speedtransducer fail in service the ECU idle speed controlwould become erratic.

J

:.....j

4 REVISED: APR. 87

Page 5: 14cux Fuel Injection

: ..

‘.’ :

., .’

.,

‘. ,‘,‘.‘. :::, ..i.’

FOE; 1987 FUEL INJECTION SYSTEM b ii\

INERTIA SWITCH

The inertia switch is a mechanically operated switchlocated under the left hand front seat attached tothe seat base rear cross-member.The switch is normally closed and is in the ignitionfeed (fuse to fuel pump). In the event of a suddenimpact the switch opens, and disconnects theelectrical feed to the fuel pump. The switch is resetby pressing down the button.

RELAYS

The two electronic fuel injection relays are locatedunder the front right hand seat mounted forward ofthe E.C.U. The main relay is energized via the E.C.Uwhen the ignit ion is switched on and suppliescurrent to the fuel injection system. The fuel pumprelay is energized by the E.C.U. which in turnoperates the fuel pump to pressurize the fuelsystem.

E.F.I. WARNING SYMBOL (Instrument binnacle)

An E.F.I. warning symbol incorporated into theinstrument binnacle will illuminate when the E.C.U.detects that it cannot maintain correct air/fuel ratiodue to a fault in one of the follolOring fuel injectionsystem components. ‘:. ,.*a

Air flow sensor.Lambda sensor. -Water temperature thermistor. (sensor)Throttle potentiometer.

The symbol will illuminate on initial turn of theignition key as part of the bulb check feature, andwill go out after a few seconds.If the symbol illuminates when the engine is idlingor the vehicle is being driven it indicates a failure ofone of the four functions, the vehicle should bedriven with care, and the cause rectified, refer totest procedure for the particular functions. Shouldone of the functions fail, the vehicle can still bedriven due to a limp home feature incorporatedinto the fuel injection system.

..:

.‘.,.

2: :_‘. ‘*. . .. .

REVISED: JULY 88

Page 6: 14cux Fuel Injection

1987 KANCltROVER”

FUEL INJECTION SYSTEM

CAUTION: The fuel system incorporates f inemetering components that would be affected byany dirt in the system; therefore it is essentialthat working conditions are scrupulously clean.If it is necessary to disconnect any part of thef u e l i n j e c t i o n s y s t e m , t h e s y s t e m M U S T b edepressurized. All openings left open after theremoval of any component from the fuel system,MUST be sealed off (0 prevent ingress of dirt.

ENGINE SEllING PROCEDURE

If a major overhaul has been undertaken on the fuelinjection/engine system, the following check andadjustments must be carried out before attemptingto start the engine.

A. Throttle potentiometer setting - see ‘Throttlepotentiometer’ setting procedure.

B. Spark plug gaps - see ‘Section 05 Enginetuning data’.

C. Throttle levers - see ‘Throttle lever settingprocedure’.

D. Ignition timing - static - see ‘Section 86Electrical’.

C A U T I O N : I F T H E E N G I N E I S M I S F I R I N G , I TSHOULD BE IMMEDIATELY SHUT DOWN ANDTHE CAUSE RECTIFIED. FAILURE TO DO SO WILLR E S U L T I N I R R E P A R A B L E D A M A G E T O T H ECATALYSTS.

NOTE: If the previous checks and adjustmentsare satisfactory but the engine will not start theignition and fuel injection electrical circuitorym u s t b e checked using the appropriaterecommended equipment.

6

Recommended Equipment -

Lucas ‘Electronic Ignition Analyser’Lucas Part Number - YWB 119.

Lucas Diagnostic EquipmentLucas Part Number - 60600965 (complete kit)

Individual part numbers for the above kit are asfollows:

Hand held test unit - Model 2HHTLucas Part Number - 84772

Interface unitLucas Part Number

- Model 21U- 84773

Serial link leadLucas Part Number - 54744753

Memory cardLucas Part Number - 54744754

Operating manualLucas Part Number

Plastic caseLucas Part Number

::

. XXB825.I1.

- 54744755

NOTE: The Lucas diagnostic equipment can beconnected to the diagnostic plug located by theE.C.U.

Use in conjunction with the Lucas OperatingInstruction Manuals.

If the above equipment is unavailable the tests canbe carried out using a multi-meter, following the . .instructions given in the charts.

CAUTION: Ensure the multi-meter is correctly setto volts or ohms, dependent upon which test isbeing undertaken.

Carry out the following static checks beforeundertaking the continuity procedure:-

A.B.C.D.E.

F.

Fuse 18 - in main fuse panel - is intact.Inertia switch - not tripped.Fuel - ample fuel in fuel tank.Battery Condition - state of cha ge.IAir Leaks - no unmetered air entering enginesystem.Electr ical Connect ions - dry, c lean andsecure. .. . \

REVISED: jlJLY 88

Page 7: 14cux Fuel Injection

‘.

ro;;; 1 9 8 7 F U E L I N J E C T I O N S Y S T E M

CONTINUITY TEST PROCEDURE: ”

..’.IThe continuity procedure and instructions on thefollowing pages must be followed precisely toprevent damage occurring to any of the fuel systemcomponents.

To enable the tests to be carried out when the 40way multi-plug is connected to the E.C.U., it isnecessary to remove the two screws securing theshroud to the plug to enable the multi-meterprobes to be inserted into the back of theappropriate pin.

CAUTION: Tests that require the plug to beremoved from the E.C.U., must also have themeter probes inserted into the back of the plug.If the probes are inserted into the plug sockets,damage will occur to the sockets resulting inpoor connections when the plug is reconnected.

TESTING

1. Remove the E.C.U., and harness plug frombeneath the front right hand seat, access isgained through the rear opening of the seatbase.

...‘.,

.’

2. Remove the plug shroud and maneuver italong the harness until there is enoughclearance enabling meter probes to beinserted into the back of the plug.

3. There are 4 pin numbers, 1, 13, 28, 40moulded onto the rear of the plug for pinposition identification as shown in theillustration below, (for clarity the electricalleads have been omitted).

,’ Pins 1 to 13 top row.Pins 14 to 27 centre row (Pin 14 is below pin 13but is not identified on the rear of the plug).Pins 28 to 40 bottom row.

:’ 3

.-. RR2016E 40 28

PIN NOS. CABLE COLOUR

1. Red/green2. Brown/orange3. Yellow4. Black5. Brown/purple6. Yellow7. Green/blue8. Not used9. White/light green

10. Black/Yellow11. Yellow/white12. Blue/redI 3. Yellow/blue14. Black15. Brown16. Blue/purple17. Not usedI 8. White/pink19. Whitelgrey20. Red21. Yellow/blue22. Blue/red23. Blue24. Blue25. Red/black26. Green/white27. Black/grey28. Blue/grey29. Orange30. Not used31. Not used32. Greylwhite33. Not used34. Black/orange35. Blue/green36. Not used37. White/yellow38. Not used39. White/black40. Black

The last colour denotes the wire tracer colour.

Continued

; . .

REVISED: APR. 88

Page 8: 14cux Fuel Injection

FUEL INJECTION SYSTEM1987 ;;“d’;‘;;i

TESTS - Using a Muhi-Meter

The following continuity tests are intended as a guide to identifying where a fault may be within a circuit;reference should be made to the fuel injection circuit diagram for full circuit information.

KEYTO SYMBOLS

OHMMETERCONNECTIONS

ROAD SPEEDINPUT (SPEEDTRANSDUCER)

COOLANTTEMPERATURE

SENSOR

RR1782E

8

iNlTlON SWITCb

VOLTMETERCONNECTIONS

GEARINPUT SWITCH

INHIBITORSWITCH

AIR BYPASSVALVE

ELECTRONIC CONTROL UNITAND MULTIPLUG

MAIN RELAY

INJECTOR

PUMP RELAY

IGNITION COIL

TEMPORARYCONNECTION

FUEL PUMP

FUELTEMPERATURE

SENSOR

T H R O T T L E ’‘OTENTIOMETER 1 HOT WIRE AIRFLOW SENSOR

REVISED: APR. 88

Page 9: 14cux Fuel Injection

NOTE: All tests are carried out from the electronic control unit (ECU) harness multi-plug unless statedotherwise in the test procedure.

..

:,:.:.A

R”;;; 1987 FUEL INJECTION SYSTEM b-6 1

1rEST PROCEDURE

2. Check ignition supply to ECU

rEST PROCEDURE

1. Check battery supply to ECU

RESULTS . Check cables and units shown in bold

Voltmeter reading of battery volts -(mimimum battery voltage 10 volts)Proceed to Test 2Voltmeter reading of zero voltsCheck:-

1

IGNlTlON OFF

RRl816E

RESULTS - Check cables and units shown in bold

Voltmeter reading of battery volts -(minimum battery voltage 10 volts)Proceed to Test 3Incorrect reading check:-

RR1817E

Y

Continued

REVISED: APR. 88

:

g .:

:.,

Page 10: 14cux Fuel Injection

l-l RANGE19 FUEL INJECTION SYSTEM lg8’ ROVER

rEST PROCEDURE

I. Check operation ofMain relay

RESULTS - Check cables and units shown in bold

Voltmeter reading of battery volts -Proceed to Test 5

Voltmeter reading of zero volts -Proceed to Test 4

IGNITION ON

RR1818E

‘EST PROCEDURE 1 RESULTS - Check cables and units shown in bold

I.

1

.

5

4

R

1 0

Fault DiagnosisMain relay circuits

A. Voltmeter reading of battery volts -Check:-If OK Suspect ECU

6. Voltmeter reading of zero voltsCheck:-

clI-lGNsnoNoPF

--..~

-iR1810E

4

REVISED: APR. 88

‘- ‘\

Page 11: 14cux Fuel Injection

k”d;‘;r; 1987 FUEL INJECTION SYSTEM 119 1

‘EST PROCEDURE

i. Check operation Listen for audible ‘click’ from pumpof pump relay relay.

If 0.K - Proceed to Test 7

IGNtTION ON

RR182OE

[EST PROCEDURE

i. Fault diagnosisPump relay circuits

1 I?R1821E

IGNITION ON

RESULTS - Check cables and units shown in bold

No audible ‘click’ from pump relayCheck:-If OK proceed to Test 6.

RESULTS - Check cables and units shown in bold

Voltmeter reading of battery volts -Suspect ECU

Voltmeter reading of zero voltsCheck:-

Y

Continued

REVISED: APR. 88

Page 12: 14cux Fuel Injection

rEST PROCEDURE RESULTS - Check cables and units shown in bold

7. Check operation of Fuel pump Voltmeter reading of battery volts -Pump operating - Proceed to Test 8

NOTE: It is not possible lo place themulti-meter probes directly onto thepump terminals. A link lead attachedto the pump is accessible behind thereal left hand wheel located betweenthe chassis and stowage area floorpanel.

(A) Voltmeter reading of batteryvolts -Pump not operatingCheck:‘-

KEY:1. Inertia switch2. Fuse 18

(6) Voltmeter reading of zero voltsCheck:-

REVISED: APR. 88

Page 13: 14cux Fuel Injection

1.

‘:; .( : . .

,‘. .::i.. .~

K’^d;\ir; 1987 FUEL INJECTION SYSTEM 119 1

~~‘EST PROCEDURE

I. Check engine speed signalCable and resistor

W1823E

TEST PROCEDURE

9. Check injectors,Injector circuit

(Pin 13 left bank injectors 1,3,5,7).

clI-IGNITION OFF

lR1824 E

RESULTS - Check cables and units shown in bold

Voltmeter reading of battery volts -Proceed to Test 9

Voltmeter reading of zero voltsCheck:-

RESULTS - Check cables and units shown in bold

Ohm-meter reading of 4-5 Ohms -Proceed to Test 10

Ohm-meter reading of 5-6 Ohms -Suspect 1 injectorOhm-meter reading of 8-9 Ohms -Suspect 2 injectorsOhm-meter reading of 16-17 Ohms -Suspect 3 injectorsCheck for open circuit injector(s)or wiring faults.

Ohm-meter reading of InfinityCheck:

Continued

REVISED: APR. 88 13

..

.

:.

..:“,‘.;.

Page 14: 14cux Fuel Injection

. .

.’-:;,

.i :.. ‘.

..’

. .::’

?,

. . i.

FUEL INJECTION SYSTEM

‘EST PROCEDURE

0. Check injectorsInjeclor circuit

pin II rightbanknjectors 2,4,6,6)

RESULTS - Check cables and units shown in bold

Ohm-meter reading of 4-5 Ohms -Proceed to Test 11.

Ohm-meter reading of 5-6 Ohms -Suspect 1 injectorOhm-meter reading of 8-9 Ohms -Suspect 2 injectorsOhm-meter reading of 16-17 Ohms -Suspect 3 injectorsCheck for open circuit injector(s) or wiring faults.

Ohm-meter reading of InfinityCheck:

10

0L-

IGNITION OFFRR1825E

TEST PROCEDURE

11. Check fuel temperaturethermistor (sensor)

11

RESULTS - Check cables and units shown in bold

Correct reading-temperature toresistance- Proceed to Test 12(Refer to Temperature ConversionCharts in Test 12

Incorrect Ohm-meter readingCheck

c lI-

IGNITION OFFRR1826E

. \

1 4 REVISED: APR. 88

Page 15: 14cux Fuel Injection

;;^d;;t; 1987 FUEL INJECTION SYSTEM 119 1

‘EST PROCEDURE

2. Check coolant temperaturethermistor (sensor)

RESULTS - Check cables and units shown in bold

Correct reading-Temperature toresistance- Proceed to Test 13(Refer to Temperature ConversionChart below.

Fuel and Coolant Ohm-meter ReadingTemperature Should be“C “F Ohms

-100 140 9100 - 930000 32" 5700 - 5900

200 680 2400 - 2600400 1040 1100 - 130060" 1400 500 - 70080° 176O 300 - 4001000 2120 150 - 200

Incorrect Ohm-meter readingCheck:-

0 I- - -

IGNtllON OFF

RR1827E

Continued

REVISED: APR. 88 15

Page 16: 14cux Fuel Injection

r-t19 FUEL INJECTION SYSTEM-.- - -.w

II

MT PROCEDURE RESULTS - Check cables and units shown in bold

13. Check air bypass valve - Part I Ohm-meter reading of 48-58 Ohms -Proceed to Test 14

Incorrect readingCheck:-

13

IGNlTtON OFFRR1828E

I TEST PROCEDURE

14. Check air bypass valve - Part 2

0-I3 -

IGNITION OFF

RESULTS - Check cables and units shown in bold

Ohm-meter reading of 48-58 Ohms -Proceed to Test 15

I Incorrect reading

ICheck:-

‘.

1 6

Y. .,

‘.*::, ‘.

REVISED: APR. 88

Page 17: 14cux Fuel Injection

.

KHNCIt 1987ROVER FUEL INJECTION SYSTEM 119 1 .. 1RESULTS - Check cables and units shown in bold

Ohm-meter reading of 5000 Ohms -Proceed to Test 16

Incorrect reading of InfinityCheck:-

[EST PROCEDURE

15. Check throttle potentiometer - Part 1

15

u3NIlloN OfT

RA1830E

rEST PROCEDURE

16. Check throttle potentiometer - Part 2

RESULTS - Check cables and units shown in bold

Correct voltmeter readings-Proceed to Test 17

Throttle Throttleclosed open

0.29 ) ( 4.6 Volts) smooth () __....__...___________ (

0.36 ) swing ( 5.0 Volts

Incorrect voltmeter readingsCheck:-

- I -C I -’ I ’

IGNITION ONRRl831E 4

Continued

REVISED: JUNE 87 17

:.

Page 18: 14cux Fuel Injection

RANGE19 FUEL INJECTION SYSTEM “*’ ROVER

‘EST PROCEDURE

17. Check ou~pul ofAirflow sensor

RESULTS . Check cables and units shown in bold

Voltmeter reading of 0.3-0.6 volts-Proceed to Test 18

Incorrect voltmeter readingCheck:-

- IGNITION ONw

PRECAUTION:

Depressurize the fuel system when fitting the fuel pressure gauge or disconnecting/replacing fuel system

components.

CAUTION: Thoroughly clean the immediate area around the fuel filter and hose connections beforedisconnecting the fuel feed line from the filter. Failure to do so could cause foreign matter to bepresent in the fuel system which would be detrimental to the fuel system components.

WARNING: The spillage of fuel from the fuel filter is unavoidable when disconnecting the fuel feedline, ensure that all necessary precautions are taken to prevent fire and explosion due to fuel vapourand fuel seepage. .

DEPRESSURIZING PROCEDURE .

a) Ignition off, pull pump relay off its terminal block.b) Crank engine for a few seconds - engine may fire and run until fuel pressure is reduced.cl Switch off the ignition.d) Connect fuel pressure gauge in the fuel supply line between the fuel rail and the fuel filter, adjacent to

the filter (see Test 18).e) Reconnect the pump relay.

18 REVISED: JUNE 87

1.

,i

,.,:.:

Page 19: 14cux Fuel Injection

,’ ‘.’

:;

:

‘..(. ‘.

FUEL INIECTION SYSTEM 119 1

NOTE: Insert the pressuregauge in the fuel feed lineimmediately after the fuelline filter. The filter islocated beneath the righthand rear wheel arch attachedto the chassis

(34.0-37.0 p.s.i.)

(6) Pressure drop-max 0.7 kgflcm’(IO p.s.9 in one minute

IGMTION OFF

1R1833E

Continued

19

Page 20: 14cux Fuel Injection

RANGEFUEL INJECTION SYSTEM lg8’ ROVER

EST PROCEDURE RESULTS - Check cables and units shown in bold

9. Check for leaking injector WARNING: Ensure that allnecessary precautions are taken

NOTE: Before removing anyof the injectors, remove andexamine the spark plugs.check for consistenlcolouration of plugs.A leaking injector willresult in the appropriatespark plug being ‘sooted up’.

IO prevent fire and explosion.

Replace any injector which leaksmore than 2 drops of fuel per minute.

Remove all injectors frommanifold but do notdisconnect from fuel rail

tR1834E

,’

Page 21: 14cux Fuel Injection

I---;

rot;; 1987 FUEL INJECTION SYSTEM

rEST PROCEDURE

!O. Check for injector operationLeft bank injectors 1,3,5,7

20 \

rEST PROCEDURE

11. Right bank injectors 2,4,6,6

IGNITION ON

RESULTS - Check cables and units shown in bold

WARNING: Ensure that allnecessary precautions are takenIO prevent fire and explosion.

Repeat test for other injectorsReplace any injector which does notoperate.NOTE: Fuel flow is 167cc minimumper minute per injeclor

RESULTS - Check cables and units shown in bold

WARNING: Ensure that allnecessary precautions are takenIO prevent fire and explosion

Repeat test for other injectorsReplace any injector which does notoperateNOTE: Fuel flow is 167cc minimum perminute per injector

Continued

Page 22: 14cux Fuel Injection

:.

‘.‘.

:.

‘: .,:.

‘. .’ ,‘:

RANGEFUEL INJECTION SYSTEM lg8’ ROVER

‘EST PROCEDURE

!2. Check gear switch input

RESULTS - Check cables and units shown in bold

Voltmeter reading of zero volts-Neutral and park

Voltmeter reading of 4.5-5.0 Volts-R.D.3.2.1 - Proceed to Test 23

Incorrect readingCheck:

1otw10r-d ON

RR1837E

22

.

. . .‘<

I.

,’ :.,

Page 23: 14cux Fuel Injection

.‘,,::. :

.

;...i

; ]‘..,‘. .

‘. :;

:‘. *

‘..,

:‘:

ro7;; 1987 FUEL INJECTION SYSTEM Ii9 1

‘_’

,,,

‘EST PROCEDURE

:3. Check road speed input

RESULTS - Check cables and units shown in bold

Voltmeter reading of 0 to 12V fluctuating 6 times perrevolution - Proceed to Test 24

NOTE: Raise and rotate the left handrear road wheel slowly Incorrect reading

Check:

IGNITCON ON

RR1838E

rEST PROCEDURE

24. Check Lambda sensor heater coils

NOTE: Remove pump relay from its conneclor

RESULTS . Check cables and unils shown in bold

Ohm-meter reading of 2.65-3.35 OhmsIncorrect readingCheck:NOTE: A reading of 5.3 lo 6.7 Ohms indicates a faultyLambda sensor

24

IGNITION OFF

RR1840E

After completing the tests with either the ‘Diagnostic’ equipment or multi-meter, re-test the vehicle to ensurethe faults have been rectified. If faults still persist, recheck using the Lucas diagnostic equipment.

2 3

Page 24: 14cux Fuel Injection

FUEL INJECrlON SYSTEM

ENGINE TUNING PROCEDURE

Before carrying out ‘Engine Tuning’ on fuel injectionvehicles, it is important that all other engine relatedsetting procedures are undertaken first; air flowsensor to air cleaner correctly fitted, ignition andthrottle potentiometer correcty set; all hosescorrectly fitted and secured.

These checks should be carried out with the enginecoolant temperature beween 80” to 95°C (176” to203°F).

CHECK AND ADJUST IGNITION TIMING

1. Check that ignition timing is at 6” 2 1” BTDC.2. Timing to be checked when engine speed is

less than 800 rev/min using a stroboscopiclamp.

3. If adjustment is necessary, loosen thedistributor clamp nut and rotate clockwise toretard or ‘counter -clockwise to advance. Whenthe required setting has been attained, tightenthe clamp nut and recheck the setting.

NOTE: Timing to be checked with vacuumhose connected.

IDLE SPEED is preset at the factory and shouldnot normally require adjustment.

CAUTION:A. If engine fails to start within a maximum time

of 12 seconds the cause must be rectified.Following rectification the engine must be runat 1500 rpm (no load) for 3 minutes to clearany accumulation of fuel in the catalysts.

B. If the engine is misfiring, it should beimmediately shut down and the causerectified.

Failure to comply with A or B will result inirreparable damage to the catalysts.

24

Page 25: 14cux Fuel Injection

.t

:j,,

:.

:

“.’

:

:

:..., .,

,;;: ‘.,

,..

‘, ‘.’

,:

;’ ‘... ‘. :

.

‘,.

,:’

.’

,’ . .

:

:.,

.,.

.‘.

‘.,

‘.

;.

yo;;; 1987 FUEL INJECTION SYSTEM 119 1.:

AIR CLEANER

Remove and Refit

Removing

1.

2.

3.

4.

5.

7.

8.9.

. .

“.

Release the two clamps secur ing the a ircleaner to the airflow sensor.Release the two nuts and bolts securing the aircleaner to the left hand valance mountingbracket.Detach the airflow sensor from the air cleaner,and lay carefully to one side.D e t a c h t h e a i r c l e a n e r f r o m t h e c e n t r emount ing bracket and withdraw from theengine compartment.Remove the large ‘0’ ring from the outlettube of the air cleaner, inspect for condition,fit a new ‘0’ ring if in poor condition.Unclip the three catches securing the inlettube to the air cleaner canister and removethe inlet tube.Remove the nut and end plate securing the aircleaner element in position.Withdraw the air cleaner element and discard.Inspect the dump valve for condition and thatit is clear of obstructions.

.; . .

RFiI854E

Refitting

AIR FLOW SENSOR

Remove and refit

Removing

NOTE: The air flow sensor is not aserviceable item. In the event of failure ordamage the complete unit is to be replaced.

Disconnect the battery negative terminal.Release the large hose clamp at the rear of theair flow meter and disconnect the hose fromthe sensor.Disconnect the multi-plug.Release the two clips securing the air flowsensor to the air cleaner case detach thesensor from the case and withdraw it from theengine compartment.

Refitting

5. Reverse the removal procedure ensuring thatthe multi-plug is firmly reconnected to the airflow sensor and that the hose clamp at therear of the sensor is securely tightened, toprevent un-metered air entering the engine.

10. Fit a new element and secure in position.11. Refit the inlet tube to the air cleaner canister.12. Refit the air cleaner to the mounting bracket

and tighten the two nuts and bolts.13. Clip the air flow sensor to the air cleaner.

REVISED: SEPT. 88 25.:...

Page 26: 14cux Fuel Injection

:,.._,. ”

FUEL INJECTION SYSTEM1987 &INGEROVER

‘.

THROlTLE POTENTIOMETER Setting the Potentiometer using a multi meter.

Remove, refit and reset

Remove

ENSURE THE MULTI METER USED TO CARRY OUTTHIS CHECK IS SET TO VOLTS. A MULTI METERSETTING OTHER THAN VOLTS WILL RESULT INDAMAGE TO THE POTENTIOMETER.

1. Disconnect the battery negative terminal.2. Disconnect the electrical three-pin plug.3. Remove the two screws securing the switch to

the plenum chamber and carefully pull theswitch off the throttle valve shaft.

8.9.

10.

11.

12.13.

Loosen the potentiometer securing screws.Reconnect the potentiometer three-pin plugand reconnect the battery. Switch on theignition.Connect the multi meter between the red andgreen leads at the potentiometer electricalplug.Rotate the potentiometer clockwise orcounter-clockwise, until the multi meter reads325 2 35 mV.Tighten the potentiometer securing screws.Re-check the multi-meter reading. Check alsofor a ‘smooth swing’ of the meter needlebetween minimum and maximum throttleopening between the voltage reading of 4.6 -5.0 volts

4. Remove the old gasket.

Refit

5. Fit a new gasket between the throttle switchand plenum chamber.

6. Align the switch and shaft fiats; slide theswitch on to the throttle shaft and secure theswitch to the plenum chamber.

7. The throttle potentiometer must be resetusing the following procedure.

CAUTION: The throttle mechanism must not beoperated whi le the potent iometer is looselyfitted, otherwise damage may be caused to thepotentiometer wiper track.

26 REVISED: SEPT. 88

NOTE: After setting the potentiometer, locka n d t a m p e r p r o o f e a c h s c r e w h e a d b ycoating them with yellow paint.

Page 27: 14cux Fuel Injection

:.

,’ :

..’ .:

,:

,’ ,~:

.’

‘, :.‘. 1

8:

,, ‘,‘,, :

.: ‘, :.:,: .‘: :

., ,’ ‘, ,‘.,I.‘,.;

,,;,. ; : :

:

.

::,, ..,‘. :,.

:

R”d;‘;r; 1987 FUEL INJECTION SYSTEM 119 1

BY-PASS AIR VALVE(STEPPER MOTOR)

: ;...Remove and refit

Removing

1.2.3.

4.

Disconnect the battery negative terminal.Remove the multi-plug from the unit.Unscrew the valve from its location at the rearof the plenum chamber.Remove the captive washer.

Refitting

5. Fit a NEW sealing washer.

,.. NOTE: If::::.’ refitted

the same by-pass valve is beingclean any previous sealing

compounds from the threads. Apply Loctite2 4 1 t o t h r e a d s o f t h e v a l v e b e f o r ereassembly.

SPEED TRANSDUCER

Remove and refit

Removing

1.

2.3.

4.

5.

6

Place the vehicle on a hydraulic hoist andapply the parking brake.Disconnect the battery negative terminal.Raise the hoist and disconnect the speedtransducer electrical plug.Disconnect the speedometer cable from thetransducer to the binnacle at the transducer.Disconnect the speedometer cable from thetransducer to the speedometer housing at thetransducer.Remove the single bol t secur ingtransducer to i ts mount ing bracketwithdraw the unit from the vehicle.

t h eand

Refitting

7. Reverse the removal instructions.

6. Tighten the valve to the specified torque (seeTorque values-section 06).

7. Reverse the remaining removal instructions.

J

27

Page 28: 14cux Fuel Injection

:

I

.’

FUEL INJECTION SYSTEM

ELECTRONIC FUEL INJECTION RELAYS

incorporated into the fuel injection electrical circuitsare two relays. The relays are located beneath thefront

1.

right-hand seat, adjacent to the E.C.U.

F u e l p u m p r e l a y ( m o u n t e d o n a b l u eterminal block).

Main relay (mounted on a black terminalblock).

Diagnostic plug.

RRl867ERRl867E

Remove and refitRemove and refit

RemovingRemoving

1. Disconnect the battery negative terminal.1. Disconnect the battery negative terminal.2. Pull the relay(s) from the multi-plug(s).2. Pull the relay(s) from the multi-plug(s).

RefittingRefitting

3. Reverse the removal procedure.3. Reverse the removal procedure.

ELECTRONIC CONTROL UNIT-ECU‘,,,

NOTE: The ECU is not itself a serviceableitem, in the event of a unit failure, the ECUmust be replaced.

Remove and refit

Removing

1.2.

3.4.5.

6.

7.

Disconnect the battery negative terminal.The ECU is located under the front right handseat and is accessible through the rearopening of the seat base when the seat is inits most forward position.Release the E.C.U plug retaining clip.Pull the rear of the multi-plug out of the ECU.M a n e u v e r t h e t r o n t o f t h e p l u g f i n t h edirection of the bold arrow) to release the 1hooked rear end of the plug from theretaining peg.Release the screws securing the ECU to themounting bracket.Withdraw the ECU from the spring clip andremove it from the vehicle.

,:’ .i .r

Refitting

8. Refit the E.C.U. securely in’the spring clip andtighten the two screws.

9. Re-connect the E.C.U. harness plug, ensurethe plug is firmly pushed into its location andthat the retaining clip secures the plug inposition.

4

.’

8.

:‘, 28

:,: ‘...,..

Page 29: 14cux Fuel Injection

FUEL INJECTION SYSTEM

INERTIA SWITCH

The inertia switch is located under the left handfront seat attached to the inner face of the rearfront seat base. Access to the switch is gainedthrough the opening at the rear of the seat base.

Remove and refit

Removing

1. Ensure the seat is in its fully forward position.2. Disconnect the battery negative terminal.3. Remove the two screws securing the switch to

the cross member.4. Withdraw the switch and disconnect the

electrical multi-plug.5. Remove the switch from the vehicle.

Refitting

6. Reverse the removal procedure ensuring thatthe multi-plug clips firmly into position, andthat the plunger is reset (plunger is in itslowest position).

FUEL TEMPERATURE THERMISTOR (SENSOR)

Remove and refit

Removing

N O T E : N o f u e l l e a k a g e w i l l o c c u r w h e n t h ethermistor is r e m o v e d f r o m t h e f u e l r a i ltherefore it is not necessary to depressurize thefuel system before removal.

1. Disconnect the battery negative terminal.2. Remove the electrical multi - plug from the

thermistor.3. Release the thermistor from the fuel feed rail.

Refitting

4. Reverse the removal procedure, ensuring thatthe thermistor is tightened securely in the fuelrail.

REVISED: APR. 88 29

: .:

Page 30: 14cux Fuel Injection

- KANW19 FUEL INJECTION SYSTEM 1987-88 R(-j”ER

COOLANT TEMPERATURE THERMISTOR (SENSOR)

Remove and refit

Removing

1.2.

3.4.

5.

Remove the multi-plug from the thermistor.Release the radiator bottom hose and partiallydrain the cooling system.Refit the hose and tighten the clamp securely.Remove the thermistor from the left handfront branch of the intake manifold.Remove the copper washer.

Refitting

6.7.

8.9.

30

Fit a NEW copper washer to the thermistor.Fit the thermistor to the intake manifold andtighten securely.Refill the cooling system.Run the engine, check for water leaks aroundthe coolant temperature thermistor.

RESETTING THROTTLE LEVERS

NOTE: The setting procedure outlined isapplicable at minimum throttle conditiononly.

Ensure that the throttle valve is retained at its90” vertical setting by holding down the stoplever and throttle/kick down lever denoted bythe bold arrow while adjusting the throttleoperating levers.Release the throttle operating lever securingscrew and adjust the lever until contact ismade with the top end of the slot in thethrottle lever mounting bracket; retaining thelever in this position retighten the screw.Lightly grease all throttle lever bearing surfacesand torsion spring with Admax 13 grease or asuitable equivalent.

NOTE: Check the c learance between thecruise control actuator l ink and throt t lelever (see Cruise Control ActuatorSetting-Section 19, Page 47).

.__

LATER MODELS:- have a redesigned stop lever thatseats on a factory-set adjustment screw which islocated in the plenum chamber casting. The screwshould not normally require adjustment. If newthrott le bracketry and l inkages are f i t ted it isadvisable to check that the throttle valve is verticalbefore adjusting the screw.

REVISED: APR. 88 :,.._..

Page 31: 14cux Fuel Injection

FUEL INJECTION SYSTEM

1

THROl-FLE CABLE

Remove and refit

Removing

1.

2.

3.

Remove the cotter pin and clevis pin securingthe cable to the lever.Carefully pry the throttle cable adjustment nutout of the linkage mounting bracket.W i t h d r a w t h e c a b l e f r o m t h e m o u n t i n gbracket.

i,io 2,i2

RRl064E

Release the outer cable from the retainingclips within the engine compartment.Remove the lower dash pane! from beneaththe steering column.Disconnect the cable from the throttle pedaland release the cable locknut.Feed the cable through the bulkhead grommetand into the engine compartment.

FIT NEW THROlTlE CABLE

8. Feed the new c a b l e f r o m t h e e n g i n ecompartment through the bulkhead grommet.

9. Connect the cable to the throttle pedal.

10. Connect the cable to the throttle linkage, fit anew cotter pin and secure in position.

11. Clip the outer cable adjustment nut into themounting bracket.

12. Adjust the outer cable to give 1.57 mm (0.062in) free play in the throttle cable and checkthe throttle operation.

THROlTLE PEDAL

Remove and refit

Remove

1. Release the six screws securing the lower dashpanel, lower the panel and disconnect the twoelectrical leads to the rheostat switch, detachthe bulb check unit from the spring clip andremove the dash panel from the vehicle.Remove the cotter pin and clevis pin securingthe throttle cable to the throttle pedal.Release the tension from the pedal returnspring.Remove the circlip from the pedal pivot pin.Withdraw the pivot pin.

NOTE: It may be necessary to remove thesteering column fixings enabling thecolumn to be lowered to gain access to thepedal pivot pin circlip.

6. Withdraw the throttle pedal.

Refitting

7. Lightly grease the pivot4pin and clevis pinbefore re-assembly.

8. Fit a NEW cotter pin to the clevis pin.9. Reverse the remaining removal instructions.

31

Page 32: 14cux Fuel Injection

.’ 1

:

:

,

: :

:.

‘,, .:,:::,: ‘,‘.

FUEL INJECTION SYSTEM 1987-88 PO;;;

PLENUM CHAMBER

Remove and refit

Removing

1.2.

3.

4.

8.

Disconnect the battery negative terminal.Release the radiator bottom hose and partiallydrain the cooling system, reconnect the hoseto the radiator.Release the two large hose clamps from theneck of the plenum chamber and outlet boreof the airflow sensor and remove the hosefrom its location.Release the clamps and remove the twocoolant hoses from the bottom of the plenumchamber inlet neck. Identify each hose to aidre-assembly.Remove the vacuum supply hose from thecruise control actuator.Disconnect the actuating link at the cruisecontrol actuator.Remove the distributor vacuum hose, positivecrankcase ventilation breather filter hose andservo hose.Disconnect the throttle potentiometermulti-plug.

9.

10.

11.

Disconnect the multi-plug from the air by-passvalve.Disconnect the small vacuum hose at the rearof the plenum chamber, located below the airby-pass valve.Remove the hose from the air by-pass valve toplenum chamber to enable the small returnspring located below the throttle levers to beunhooked.

12. Release the two throttle return springs.13. Remove the two bolts (with spring washers)

securing the throttle cable and kick-downcable anchor bracket to the throttle leversupport bracket, lay the assembly to one side.

14.

15.

Remove the six socket head bolts (with plainwashers) securing the plenum chamber to theram housing.Maneuver the plenum chamber and remove itfrom the ram housing.

NOTE: To prevent ingress of dirtram tubes, place a protective coverram tube openings.

into theover the

i

3 2

Page 33: 14cux Fuel Injection

;;“d;‘;;i 1987-91 FUEL INJECTION SYSTEM

Refitting RAM HOUSING

16. Ensure that all mating faces are free from anyprevious sealing compounds.

17. Coat the mating faces of the plenum chamberand ram housing with ‘Hylomar’ sealant.

18. Refit the plenum chamber and tighten the sixbolts to the specif ied torque (see torquevalues-section 06).

19. When refitting the small return spring, item 11in the removal procedure, it must be notedthat the ‘hooked’ open end of the springMUST face the plenum chamber as shown inillustration RR2292E below.

20. Reverse the remaining removal instructions.

NOTE: Ensure that all hoses are connectedsecurely to prevent un-metered air enteringthe engine.

Remove and refit

Removing

1. Disconnect the battery negative terminal.2. Remove the plenum chamber (see Plenum

Chamber remove and refit).3. Release the hoses from around the outer

edges of the ram housing.4. Remove the six through bolts (with plain

washers) securing the ram housing to theintake manifold.

5. Lift the ram housing off the intake manifoldand remove it from the engine compartment.

6. Place a protective cover over the top of theintake manifold inlet bores to prevent ingressof dirt.

Refitting

7. Ensure that all mating faces are clean and freefrom dirt and any previous sealingcompounds.

8. Apply ‘Hylomar’ sealant to the intake manifoldface before refitting the ram housing.

9. Fit the ram housing and retighten the bolts,working from the two centre bolts, diagonal11towards the outer four bolts.

10. Tighten to the correct torque (See section06-Torque values).

REVISED: SEPT. SO 33;: _:

Page 34: 14cux Fuel Injection

FUEL INJECTION SYSTEM 1987-91 PO;;;

DEPRESSURIZING THE FUEL SYSTEM

WARNING: Under normal operating conditionsthe fuel injection system is pressurized by a highpressure fuel pump, operating at up to 2.3 to 2.5bar (34 to 37 p.s.i.1. When the engine isstationary this pressure is maintained within thesystem. To prevent pressurized fuel escaping andto avoid personal injury it is necessary todepressurize the fuel injection system beforeany service operations are carried out.

NOTE: If the vehicle has not been run there willstill be a small amount of residual pressure inthe fuel line. The depressurizing procedure muststill be carried out before disconnecting thecomponent within the fuel system.

WARNING: The spilling of fuel is unavoidableduring this operation. Ensure that all necessaryprecautions are taken to prevent fire andexplosion.

1.

2.

3.4.

5.

6.

The fuel pump relay is located under the frontright hand seat.Pull the fuel pump relay off its multi-plug (seeElectronic Fuel Injection Relays-Section 19,Page 28).Start and run the engine.When sufficient fuel has been used up causingthe fuel line pressure to drop, the injectorswill become inoperative, resulting in enginestall. Switch the ignition off.Disconnect the battery negative terminal.

NOTE: Fuel at low pressure will remain inthe system. To remove this low pressurefuel, place an absorbent cloth around thefuel feed hose at the fuel rail and releasethe fuel feed hose at the appropriate end.

Disconnect either:a) The nut and ferrule at the fuel railOR

NOTE: If the original regulatorrefitted, fit a NEW ‘0’ ring to thepipe.

b) The hose at the inlet end of the fuel filter. Refitting

Refitting 7.

7. Refit the fuel feed hose.8. Refit the fuel pump relay, reconnect the

battery.9. Crank the engine (engine will fire within

approximately 6 to 8 seconds).

FUEL PRESSURE REGULATOR

Remove and refit

Removing

1.2.3.

4.

5.

6.

Depressurize the fuel system.Disconnect the negative battery terminal.Release the hose clamp securing the fuelreturn hose to the regulator and remove thehose.Pull the vacuum hose from the rear of theregulator.Remove the two nuts and bolts securing theregulator to the fuel rail, carefully ease theregulator fuel inlet pipe out of the fuel rail.Withdraw the regulator from the enginecompartment.

is beingfuel inlet

8.9.

Lightly coat the ‘0’ ring with silicon grease300 before fitting the regulator to the fuel rail.Reverse the removal procedure.Reconnect the batter), and pressurize the fuelsystem and check that there are xo fuel leaksaround the regulator connections.

34 REVISED: SEPT. 90

Page 35: 14cux Fuel Injection

;;^d;‘;; 1987-88 FUEL INJECTION SYSTEM

,’

,’ .’FUEL RAIL-INJECTORS R/H AND UH

Remove and refit

Removing

1.2.3.

4.

5.. .‘.‘...‘,. . .,‘,.,., .

, ,‘..._ .’ .., 6.‘..: ‘:

7.

8.

Depressurize the fuel system.Disconnect the negative battery terminal.Remove the plenum chamber. (See PlenumChamber, remove and refit).Remove the ram housing. (See Ram Housingremove and refit).

NOTE: Place a cloth over the ram tubeopenings to prevent ingress of dirt into theengine.

Release the hose clamp and remove the fuelreturn hose from the pressure regulator.D isconnect the mul t i -p lug f rom the fue ltemperature thermistor (sensor).Disconnect the multi-plugs from the eightinjectors.Remove the five bolts securing the fuel railsupport and heater pipe brackets to the intakemanifold. Lay the heater pipes to one side.

11. If necessary, remove the two nuts and boltssecuring the regulator to the fuel rail, andcarefully pull the regulator away from the rail.

Refitting

12. Fit NEW ‘0’ rings, protective cap andsupporting disc to the injectors, lightly coatthe ‘0’ rings with silicon grease 300 and insertthe injectors into the fuel rai l , mult i-plugconnections facing outwards.

13. Refit the retaining clips.

CAUTION: Care must be taken when refitting thefuel rail and injectors to the intake manifold toprevent damage occurring to the ‘0’ rings.

14.

15.

16.17.

Fit a NEW ‘0’ ring to the pressure regulatorlightly coat the ‘0’ ring with silicon grease 300and secure the regulator to the fuel rail.Fit the fuel rail and heater pipe assemblies tothe intake manifold, secure the rail and pipesin position with the five bolts.Reverse the remaining removal instructions.Pressurize the fuel system and check for fuelleaks around the injectors and pressureregulator.

9. Remove the fuel rail, complete with injectors,from the intake manifold.

10. Remove the retaining cl ips securing theinjectors to the fuel rail, ease the injectorsfrom the rail.

--- .,

. . . . . .

‘...

Page 36: 14cux Fuel Injection

FUEL INJECTION SYSTEM 1987-88 yo$;;

INTAKE MANIFOLD

Remove and refit

Removing

Depressurize the fuel system.Disconnect the battery negative terminal.Release the hose clamp and remove theradiator bottom hose to enable the coolingsystem to be partially drained, so that coolantlevel is below the thermostat housing, refit thehose and secure in position with the hoseclamp.Remove the plenum chamber (see PlenumChamber, remove and refit).Remove the ram housing (see ram housingremove and refit).

CAUTION: Place a protective cover over theintake manifold openings to prevent ingress ofdirt.

6.

7.

8.

9.

10.

11.

12.

36

Disconnect the electrical multi-plugs to thefuel temperature thermistor (sensor), coolanttemperature thermistor (sensor) and injectors.Remove the two nuts and bolts securing thepressure regulator to the fuel rail, ease theregulator out of the rail, seal the end of thefuel rail with suitable plastic plugs to preventingress of dirt.

NOTE: The intake manifold can be removedfrom the cylinder block without removingthe fuel rail and injectors.

Disconnect the electr ical leads from theair-conditioning engine coolant sensor locatedon the thermostat elbow.Disconnect the electrical leads to the coolanttemperature transmitter (sensor) located at thefront of the intake manifold.Remove the injector harnesses from behindthe fuel rail and lay to one side.Release the hose clamps securing the twoheater hoses to the rigid heater pipes at thefront of the right hand rocker cover.Remove the two bolts securing the r igidheater pipes to the intake manifold and easethe pipes out of the hoses.

13. Lay the heater pipe assembly to one side.14. Release the twelve bolts securing the intake

manifold to the cylinder heads.15. Lift the manifold off the cylinder heads and

remove from the engine compartment.16. Remove the two gasket clamps from the top

of the cylinder block.17. Li f t off the gasket and remove the gasket

seals.18. Remove previous sealing compound from

around the water passage openings of thecylinder heads.

Refitting

19. Locate the NEW seals in position with theirends engaged in the notches formed betweenthe cylinder heads and block.

, ‘.

20. Lightly apply ‘Hylomar’ sealant around theoutside of the water passage openings on thecylinder heads, manifold gasket and intakemanifold. ?

,.‘I,

‘.,:

iz,‘..

Page 37: 14cux Fuel Injection

FOE; 1987-91 FUEL INJECTION SYSTEM

‘. :.. .

201

: ”

.,:: :

21.

22.

23.

24.

25.

26.

27.28.29.

Fit the manifold gasket with the word ‘FRONT’to the front and the open bolt hole to thefront right hand side.F i t t h e gasket c l a m p s b u t DO NOT f u l l ytighten the bolts at this stage.Locate the intake manifold onto the cylinderheads, clean the threads of the manifoldsecuring bolts.Fit all manifold bolts and tighten them a littleat a time, evenly, alternate sides working fromthe centre outwards.Tighten to correct torque (see section 06Torque values).Tighten the gasket clamps to the correcttorque (see section 06 Torque values).Reverse remaining removal instructions.Replenish the cooling system.Start the engine, check for water and fuelleaks.

FUEL FILTER

Remove and refit

Refitting

WARNING: The spilling of fuel is unavoidableduring this operation. Ensure that all necessaryprecaut ions are t a k e n t o p r e v e n t f i r e a n dexplosion.

1.2.

3.

4.

5.

Depressurize the fuel system.The fuel filter is located on the right handchassis side member fotward of the fuel tankfi l ler neck. Access to the f i l ter is gainedthrough the right hand rear wheel arch.Thoroughly clean the immediate area aroundthe hose connections to prevent ingress offoreign matter into the fuel system.Loosen the two hose clamps nearest the filterto enable the hoses to be removed from thefilter canister. Plug the end of the hoses toprevent ingress of dirt.Release the securing bolt and bracket andremove the f i l te r f rom the chass i s s idemember.

Refitting

6. Fit a new filter observing the direction of flowarrows stamped on the canister.

7. Start the engine and inspect for fuel leaksaround the hose connections.

REVISED: SEPT. 90 37

Page 38: 14cux Fuel Injection

‘. 8.

‘_’

.:

‘. .’

‘,

..

:..

.,,‘Y.:

,..

..‘.

‘_

,. .’

: ”

; ‘:

: ”

..,

.’

KANGIZFUEL INJECTION SYSTEM 1987-91 ROVER

.*

FUEL TANK

Remove and refit

Removing

WARNING: Ensure that the Fuel HandlingPrecautions given in Section 01 - Introductionregarding fuel handling are strictly adhered towhen carrying out the following instructions.

CAUTION: Before disconnecting any part of thefuel system it is imperative that all dust, dirt anddebris is removed from around the componentsto prevent ingress of foreign matter into the fuelsystem.

1.2.

3.4.

5.6.

Drive the vehicle onto a suitable hoist.Depressurize the fuel system. (seedepressurizing procedure-page 34)Disconnect the battery negative terminal.Disconnect the electrical leads to the fuel tanksender unit. Disconnect the fuel pumpelectrical multiplug, access to which is gainedthrough the left hand rear wheel arch, theplug is located between the underside of thebody and chassis side member.Raise the hoist.Remove the drain plug from the bottom of thefuel tank and drain the fuel into a suitablecontainer that can be sealed afterwards.ENSURE THAT THE TANK IS DRAINEDCOMPLETELY.Refit the drain plug (refer to Warningconcerning fuel handling at start of thisprocedure.

From underneath the vehicle

7.

8.

9.

Disconnect the fuel hose from the inlet sideof the fuel filter.Disconnect the fuel return pipe to the fueltank.Remove the breather hose and threeevaporative loss hoses from the fuel tank, sealall hose and pipe openings to prevent ingressof foreign matter.

RRPOIOE

*f .,

3

IO. Release the two large hose clamps, securingthe inter-connecting hose to tank and fillertube, maneuver the hose up the outside ofthe filler tube to enable it to be withdrawnfrom the tank filler neck.

‘..

‘-’ ,,. , :>

11. With assistance from a second personsupporting the fuel tank, remove the four tankfixings.

12.

13.

14.

Tilt the left hand side of the tank downwardsand maneuver it out of the chassis frame. Careshould be taken to ensure that the fuel feedpipe to filter is not damaged when loweringthe tank.Place the tank in a safe area and ensure that allnecessary precautions are undertaken to makeall personnel within the vicinity aware that thetank will give off residual fuel fumes.If necessary remove the fuel pump from thetank. (See Fuel Pump remove and refit).

Refitting

15.

16.

17.

3 8 REVISED: SEPT. 90

Refit the fuel tank to the chassis, taking careto relocate the fuel feed pipe grommetsbetween the fuel tank and chassis.Reverse the removal procedure, ensuring thatthe sealing ring. fuel line and hoseconnections are secure. I(Run the engine and re-check all connectionsto ensure no fuel leaks exist. Reverse theremaining removal procedure. Recode theradio.

‘l..,

Page 39: 14cux Fuel Injection

FUEL INJECTION SYSTEM iI-9 1

FUEL PUMP

Remove and refit

Removing

WARNING: Ensure that the Fuel HandlingPrecautions given in Section 01 - Introductionregarding fuel handling are strictly adhered towhen carrying out the following instructions.

1. Drive the vehicle onto a suitable hoist.2. Depressurize the fuel pump system. (see

depressurizing procedure-page 34)3. Disconnect the battery negative terminal.4. Remove the fuel tank from the chassis frame.

(see fuel tank remove and refit-page 38)5. Place the tank in a safe area.6. Disconnect the fuel supply hose from the

pump.7. Remove any previous sealant from the top of

the pump flange.8. Remove the five screws and withdraw the

pump from the tank.

Refitting

9. Clean the immediate area around the pumpopening in the fuel tank.

10. Fit a NEW pump seal.11. Secure the pump to the tank and tighten the

screws securely.12. Liberally coat the heads of the screws and

flange of the fuel pump with Sikaflex 221flexible adhesive sealant.

13. Reverse the removal procedure, ensuring thatthe sealing ring, f u e l l i n e a n d h o s econnections are secure. Recode the radio.

14. Run the engine and re-check all connectionsto ensure no fuel leaks exist. Reverse theremaining removal procedure.

Continued

REVISED: SEPT. 90 39

Page 40: 14cux Fuel Injection

KANGEFUEL INJECTION SYSTEM 1987-91 ROVER

FUEL PIPES KEY

WARNING: Depressurize fuel sys tem be foredisconnecting any of the fuel pipes and ensurethat all necessary precautions are taken againstfuel spillage.

1. Fuel feed hose to fuel rail.2. Fuel return hose to fuel tank.3. Rigid fuel feed pipe.4. Rigid fuel return pipe.5. Fuel filter.6. Rigid fuel feed pipe to filter.7. Breather hose.8. in-tank fuel pump.9. Fuel filler neck.

10. Fuel tank.

RRPOISE

REVISED: SEPT. SO

Page 41: 14cux Fuel Injection

;;^d;& 1 9 8 9 FUEL INJECTION SYSTEM 11%) 1

1

I’

I

-+

36

12626294

23106

2434

65

332 114

UPNO

‘,

AF32884E I SVI

FUEL INJECTION - Circuit Diagram - 1989 Model Year

1. 40 way connector to Electronic Control Unit(ECU).

2. Lambda sensor (left side - bank A).3. Lambda sensor fright side - bank 6).4. By-pass air valve (stepper motor) (fast idle).5. Lambda sensor screened ground.6. Fuse 18 - main fuse panel.7. Inertia switch.8. Fuel pump.

18. Fuel temperature thermistor (sensor) (input).19. Throttle potentiometer.20. Air flow sensor.21. Fuel pump relay.22. Main relay.23. Injectors-l to 8.24. Pick-up point E.F.I. warning symbol (instrument

binnacle).

9. Ignition switch.10. Speed transducer (road speed input).11. Neutral switch (automatic gearbox) (load

input).12. Main cable connector.13. Battery.14. Diagnostic plug.15. In-line resistor.16. Coil/-ve (engine RPM input).17. Coolant temperature thermistor (sensor)

(input).

25. Heated front screen sense.26. Purge control valve.27. 12\/ from fan relay.28. Air conditioning switch sense.29. Air conditioning output co?itrof.30. Air conditioning load input.31. Fan relay feed.32. Heater/air con. cable connector.33. Condenser fan timer control.

= = = Denotes screened ground.

NOTE: Reference to left and right side is made when viewing vehicle from rear. 1

ADDITION: SEPT. 88 / REVISED: MAY 89 41

Page 42: 14cux Fuel Injection

\

19 FUEL INJECTION SYSTEMRANGE

lg8’ ROVER

FUEL INJECFION SYSTEM

For 1989 model year, the EFI system has a Lucas14CU electronic control unit. This is a developmentof the 13CU used on 3.5 litre vehicles.In most respects the 14CU works in the same wayus ing the same engine components , i t doeshowever have additional capacity, enabling it tocontrol fuel tank vapour purging and airconditioning.

Condenser fans

I t shou ld be noted that under h igh coolanttemperatures, when the engine is switched off, thecondenser fans will be activated and will run forapproximately ten minutes.

Throttle potentiometer

A further improvement is the f i t t ing of a ‘selfadaptive’ throttle potentiometer. This means thatadjustment of the thrott le potentiometer is nol o n g e r p o s s i b l e . I t also means that thepotentiometer sett ing is not lost, for example,when throttle stop wear occurs.

Purge valve

The operation of the charcoal canister purge valveis checked during the fuel injection system test. SeeTESTS 9 and 10 Section 19, page 48.

Recommended equipment

The diagnostic equipment used for checking outthe l4CU system is the same as that used forI~CU, with the addition of a new memory card forthe Hand held test unit.

14CU Memory cardLucas Part Number - 54746500

CONTINUITY TEST PROCEDURE

Test procedure using a multi-meter is carried out asfor 13CU, with the addition of tests for the purgecontrol valve, air conditioning, heated front screenand condenser fan inputs.The use of a hand held vacuum pump, for examplea ‘Mityvac’, is required to carry out Tests 9 and IO.Note that the 40 way multi-plug to the ECU iswired as in the following table.

PIN NOS. CABLE COLOUR

1. Redigreen2. Brown/orange3. Yellow4. Black5. Black/white6. Yellow7. Green/blue8. Purple/yellow9. White/light green

10. Black/Yellow11. Yellow/white12. Blue/red13. Yellow/blue14. Black15. Brown16. Blue/purple17. Grey/yellow18. White/pink19. Whitelgrey20. Red21. Yellow/black22. Blue/red23. Blue24. Blue25. Red/black26. Green/white27. BlackIgrey28. Blue/grey29. Orange30. Not used31. Not used32. Creylwhite33. Black/grey34. Black/orange35. Blue/green36. Black/green37. White/yellow 438. Not used39. White/black40. Black

The last colour denotes the wire tracer colour.

4 2 ADDiTlON: SEPT. 88 / REVISED: MAY 89

Page 43: 14cux Fuel Injection

K”d;‘;rt 1 9 8 9 FUEL INJECTION SYSTEM

TESTS - Using a Multi-Meter - 14CU system - Key to Symbols

The following continuity tests are intended as a guide to identifying where a fault may be within a circuit;reference should be made to the fuel injection circuit diagram for full circuit information.

ELECTRONIC CONAND MULTIPLUG CONNECTION

PUMP RELAY FUEL PUMP

ROAD SPEEDINPUT (SPEEDTRANSDUCER)

TEMPERATUREPOTENTIOMETER HOT WIRE AIRFLOW METER

ADDITION: SEPT. 88 / REVISED: MAY 89 43

Page 44: 14cux Fuel Injection

..’,.. 1

,.’ .

l-119 FUEL INJECTION SYSTEM 1989 t(ANbtROVER

NOTE: Ail tests are carried out from the electronic control unit (ECU) harness multi-plug unless statedotherwise in the test procedure.

‘EST PROCEDURE

. Check battery supply to ECU

RESULTS - Check cables and units shown in bold

Voltmeter reading of batten/ volts -(mimimum battery voltage IO volts)Proceed to Test 2Voltmeter reading of zero voltsCheck:-

IGNITION OFF

TEST PROCEDURE

2. Check ignition supply to ECU

RESULTS - Check cables and units shown in bold

Voltmeter reading of battery volts -(minimum battery voltage 10 volts)Proceed to Test 3Incorrect reading check:-

1 1 /

-mI-0’ I ’

IGNITION ONRR262OE

44 ADDITION: SEPT. 88 I REVISED: MAY 89

:.

Page 45: 14cux Fuel Injection

k”d;‘ir; 1989 FUEL INIECTION SYSTEM 119 1

rEST PROCEDURE

I. Check operation ofMain relay

I -4

RESULTS - Check cables and units shown in bold

Voltmeter reading of battery volts -Proceed to Test 5

Voltmeter reading of zero volts -Proceed to Test 4

I

J

\ 1 /-aI-

c l’ I \

IGNITION ON

1. Fault Diagnosis Voltmeter reading of battery voltMain relay circuits

IGNITION OFF

Continued

ADDITION: SEPT. 88 ! REVISED: MARCH SO 45

Page 46: 14cux Fuel Injection

.. I

..:

‘..’

:

.p

.’

.

,;. .‘.,

1,:

.:,.

,’‘,: ,.:

1191 FUEL INJECTION SYSTEM 1989 K”d;;;

rEST PROCEDURE 1 RESULTS - Check cables and units shown in boldF

1

!i. Check engine speed signal Voltmeter reading of 9.5 volts + 1 voltCable and resislor Proceed to Test 6

Voltmeter reading of zero voltsCheck:-

1 1 /-a-0’ I ’IGNITION ON

RR2631E

-EST PROCEDURE

i. Check operationof pump relay

RESULTS - Check cables and units shown in bold

Test lamp will illuminate for approximately1 second when ignition is switched onIf 0.K - Proceed to Test 8

Lamp does not illuminateCheck:-If OK proceed to Test 8

RR2632EIGNlTtON ON

4

46 ADDITION: SEPT. 88 / REVISED: MARCH 90

Page 47: 14cux Fuel Injection

., -.

:

:

1,‘.

FUEL INJECTION SYSTEM 119 1

TEST PROCEDURE RESULTS - Check cables and units shown in bold

7. Fault diagnosisPump relay circuits

Voltmeter reading of battery volts -Suspect ECU

Voltmeter reading of zero voltsCheck:-

IGNITION ONRR2833E

TEST PROCEDURE

I. Check operation of Fuel pump

NOTE: II is not possible to place themulti-meter probes directly onto thepump lerminals. A link lead attachedlo the pump is accessible behind therear left hand wheel located betweenthe chassis and stowage area floorpanel.

KEY:1. Inertia switch2. Fuse 18

RESULTS - Check cables and unhs shown in bold

Voltmeter reading of battery volts -Pump operating - Proceed to Test 10

(A) Voltmeter reading of batteryvolts -Pump not operatingCheck:-

(B) Voltmeter reading of zero voltsCheck:-

IGNITION ON

RR2634E

Continued

ADDITION: SEPT. 88 I REVISED: DEC. 88

Page 48: 14cux Fuel Injection

1191 FUEL INJECTION SYSTEM 1989 Tv\IYUCP(\VFR.-- m.v . L..

I I

TEST PROCEDURE RESULTS - Check cables and units shown in bold

9. Check purge valve. Part 1 - seating Vacuum should hold for 2.5 minutes1. Disconnect pipe from purge valve lo If vacuum correct proceed to test 10

plenum (al plenum)2. Connect vacuum pump to pipe to purge

valveIf vacuum incorrect check:

3. Apply vacuum of 2.5 in/Hg

3

0I -

IGNITION OFF

9R2212E

TEST PROCEDURE

10. Check purge valve. Part 2 - operation1. Apply vacuum - 2.5 in/Hg, switch

ignition on

RESULTS - Check cables and units shown in bold

Vacuum should be releasedIf OK proceed to test 11

2. Connect pins 16 and 17 to earth toenergise pump relay.

If vacuum not released check:

-m-0

’ I ’IGNITION ON

RR2OlSE

-_

48 ADDITION: SEPT. 88 / REVISED: DEC. 88

.

I

._\.I. . .

:. .;

Page 49: 14cux Fuel Injection

R”d;;;i 1989 FUEL INIECTION SYSTEM 119 1

” ,

.,”

:’

; :’

,.

‘.*.

1

(. .‘.;:. .: .::F.‘,

. .

‘. ,:

rEST PROCEDURE

Il. Check injectors,Injector circuit

RESULTS - Check cables and units shown in bold

Ohm-meter reading of 4-4.5 Ohms -Proceed to Test 12

Ohm-meter reading of 5-6 Ohms -Suspect 1 injectorOhm-meter reading of 8-9 Ohms -Suspect 2 injectors

Pin 13 left bank ‘A’ injectors 1,3,5,7). Ohm-meter reading of 16-17 Ohms -Suspect 3 injectorsCheck for open circuit injector(s) or wiring faults.

Ohm-meter reading of InfinityCheck:

IGNITION OFF

RR2535E

I-EST PROCEDURE

12. Check injectors,Injector circuit

IPin 11 rightbank ‘B’ injectors 2,4,6,6)

RESULTS - Check cables and units shown in bold

Ohm-meter reading of 4-4.5 Ohms -Proceed to Test 13

Ohm-meter reading of 5-6 Ohms -Suspect 1 injectorOhm-meter reading of 8-9 Ohms -Suspect 2 injectorsOhm-meter reading of 16-17 Ohms -Suspect 3 injectorsCheck for open circuit injector(s) or wiring faults.

Ohm-meter reading of InfinityCheck:

IGNITION OFF

I.L”““b

Continued

ADDITION: SEPT. 88 / REVISED: DEC. 88 49

Page 50: 14cux Fuel Injection

..:

.‘i,

. . .‘. . .

,: 0

.:.

::.

X

.

1191 FUEL INIECT’ION SYSTEM1989 k”d;\;;i

reading-temperature to

ature Conversion

IGNITION OFF

50 ADDITION: SEPT. 88 / REVISED: DEC. 88

Page 51: 14cux Fuel Injection

FUEL INJECTION SYSTEM 119 1

Temperature Conversion

Should beOhms

9100 - 93005700 - 5900

IGNITION OFF

,::

Continued

ADDITION: SEPT. 88 51

Page 52: 14cux Fuel Injection

l-i19 FUEL INJECTION SYSTEM

MT PROCEDURE

15. Check air bypass valve - Par( 1

RESULTS - Check cables and units shown in bold

Ohm-meter reading of 40-60 Ohms -Proceed to Test 16

Incorrect readingCheck:-

IGNITION OFF

‘EST PROCEDURE

16. Check air bypass valve - Part 2

I0

RESULTS - Check cables and units shown in bold

Ohm-meter reading of 40-60 Ohms -Proceed to Test 17

Incorrect readingCheck:-

IWMOE

52 ADDITION: SEPT. 88

Page 53: 14cux Fuel Injection

,.;

__.

:_ ,’

iEST PROCEDURE

17. Check throttle potentiometer - Part I

1 7

RESULTS - Check cables and unils shown in bold

Ohm-meter reading of 4000-6000 Ohms -Proceed to Test 18

Incorrect reading of InfinityCheck:-

KiNlTlON OFF

IW641E

Throttle closed: 0.085-0.545 volts ) smooth) swing) between

RR2642E

Continued

ADDITION: SEPT. 88 ! REVISED: MAY 89 53

Page 54: 14cux Fuel Injection

.,‘i

‘. ‘,I

,I

,.:

.:

.’

..:j.’

(’ :‘..,..

.>.s (... ‘._,,

: .,,.’ ::‘.

::.‘.’?.

a

TEST PROCEDURE RESULTS - Check cables and units shown in bold

IS. Check output ofAirflow sensor

TIGNITION ON

IR2f343E

Voltmeter reading of 0.2-0.7 volts-Proceed to Test 20

Incorrect voltmeter readingCheck:-

PRECAUTION:

Depressurize the fuel system when fitting the fuel pressure gauge or disconnecting/replacing fuel systemcomponents.

CAUTION: Thoroughly clean the immediate area around the fuel filter and hose connections beforedisconnecting the fuel feed line from the filter. Failure to do so could cause foreign matter to bepresent in the fuel system which would be detrimental to the fuel system components.

WARNING: The spillage of fuel from the fuel filter is unavoidable when disconnecting the fuel feedline, ensure that all necessary precautions are taken to prevent fire and explosion due to fuel vapourand fuel seepage,

DEPRESSURIZING PROCEDURE ‘.

a) Ignition off, pull pump relay off its terminal block.b) Crank engine for a few seconds - engine may fire and run until fuel pressure is reduced.cl Switch off the ignition.d) Connect fuel pressure gauge in the fuel supply line between the fuel rail and the fuel filter, adjacent to

the filter (see Test 20).e) Reconnect the pump relay.

54 ADDITION: SEPT. 88 / REVISED: MAY 89

Page 55: 14cux Fuel Injection

.“.. .‘C--

R O V E R lg8’ FUEL INJECTION SYSTEM I19 1

‘. 1.1.:.

:

rEST PROCEDURE

10. Check fuel system pressureService tool 18C 1500

NOTE: Insert the pressuregauge in the fuel feed lineimmediately after the fuelline filter. The filter islocated beneath the righthand rear wheel arch attachedlo the chassis

RESULTS - Check cables and units shown in bold

(A) Expected reading 2,39-2,672 kgf/cm’(34.0-38.0 p.s.i.)

(B) Pressure drop-max 0.7 kgf/cm2(10 p.s.i.) in one minute

Proceed to Test 21

IQNITION ON

0I -

IGNITION OFFRR2644E --

Continued

ADDITION: SEPT. 88 / REVISED: MAY 89 55

Page 56: 14cux Fuel Injection

,’ :’

.,,

. . . .I

r-l19 FUEL INJECTION SYSTEM 1989 wiNCltROVER

EST PROCEDURE

!l. Check for leaking injector

NOTE: Before removing anyof the injectors, remove andexamine the spark plugs,check for consistentcolouralion of plugs.A leaking injector willresult in the appropriatespark plug being ‘sooted up’.

Remove all injectors frommanifold but do notdisconnect from fuel rail

RESULTS - Check cables and units shown in bold

WARNING: Ensure that allnecessary precautions are takento prevent fire and explosion.

Replace any injector which leaksmore than 2 drops of fuel per minute.

IGNITION ON

RR2648E

‘EST PROCEDURE

12. Check for injector operationLeft bank ‘A’ injectors 1,3,5,7

RESULTS - Check cables and units shown in bold

WARNING: Ensure that allnecessary precautions are takenIO prevent fire and explosion.

Repeat test for other injectorsReplace any injector which does not operate.NOTE: Fuel flow is 160-175 cc (using white spirit)or 180-195 cc fusing petrol) (minimum)per minute per injector, al 2.54 kgflcm’ (36.25 psi)system pressure at 20% 2 2°C

IGNITION ON

IR2646E

56 ADDITION: SEPT. 88 / REVISED: MAY 89

Page 57: 14cux Fuel Injection

k”d;;r; 1989 FUEL INJECTION SYSTEM 119 1

‘EST PROCEDURE

!3. Right bank ‘B’ injectors 2,4,6,8

3

Q‘; ,, \I\,

. 8IJ’\ 1 /-aI-0’ I ’IGNITION ON

RRz64R

rEST PROCEDURE

14. Check gear switch input

IGNlTlbN ON

RR2646E

RESULTS - Check cables and units shown in bold

WARNING: Ensure that aIfnecessary precautions are takenIO prevent fire and explosion

Repeat test for other injectorsReplace any injector which does not operateNOTE: Fuel flow is 160-175 cc fusing mineral spirils)or 180-195 cc (using gasoline) (minimum) per minuteper injeclor, al 2.54 kghcm’ (36.25 psi) systempressure at 20°C + 2°C

RESULTS - Check cables and unils shown in bold

Voltmeter reading of zero volts-Neutral and park

Voltmeter reading of 2.5-5.0 Volts-R.D.3.2.1 - Proceed to Test 25

Incorrect readingCheck:

ADDITION: SEPT. 88 / REVISED: SEPT. 90 57

Page 58: 14cux Fuel Injection

. .

.‘,:

..).:

:..i .;

.(.....

,,:,.

l-l19 FUEL INJECTION SYSTEM 1989 ;;^o”v‘;r;

rEST PROCEDURE

15. Check road speed input

NOTE: Raise and rotate the left handteat road wheel slowly

RESULTS - Check cables and units shown in bold

Voltmeter reading of 0 to 12V fluctuating 6 times perrevolution - Proceed to Test 26

Incorrect readingCheck:

\ 1 /

- - - -0’ I ’

IGNITION ON

RRw4aE

VOTE: Remove pump relay from its connector

IGNITION OFF

. . . c’

:

58 ADDITION: SEPT. 88 / REVISED: SEPT. 90. .‘.. :I

Page 59: 14cux Fuel Injection

FUEL INJECTION SYSTEM 119 1

rEST PROCEDURE

16a. Check Lambda sensor supply

A. LH Lambda sensor6. RH Lambda sensor

0I-IGNITION OFF

RA2707E

rEST PROCEDURE

26b. Check Lambda sensor operation

Nole: Select ‘P’ in main gearbox and run engine at1000 revlmin, normal operating temperature

A. LH Lambda sensorB. RH Lambda sensor

RR2708E

RESULTS - Check cables and units shown in bold ’

Correct Vl and V2 - 12 voltsProceed to Test 26b

Incorrect readingCheck:

RESULTS - Check cables and units shown in bold

Correct 0.5OV - l.OOV fluctuating

Incorrect 0.050 V - Check: Air leaks, faulty orcontaminated injectors, low fuel pressure - if OK fitnew Lambda sensor

Incorrect l.OOV - Check: High fuel pressure, leakinginjectors, saturated carbon canister - if OK fit newLambda sensor.

-

A a

LT

ADDITION: SEPT 88 / REVISED: SEPT. 89 59

Page 60: 14cux Fuel Injection

,;. ”

; ..‘. . .

1191 FUEL INJECTION SYSTEM1989 k”d;;i;i

‘EST PROCEDURE

!7. Check air conditioning thermostat input

RESULTS - Check cables and units shown in bold

Voltmeter reading of battery volts -Proceed lo Test 28

NOTE: Select air conditioning positionand move thermostat switch to cold

KEY:1. Fuse 82. Air conditioning switch3. Air conditioning thermostat4. High pressure switch - air conditioning5. Compressor clutch relay

27

Incorrect readingCheck:

IR2651E

NOTE: Select heater fan speed I. II or Ill

KEY:1. Fuse 6

kRZOS2E

60 ADDITION: SEPT. 88 / REVISED: SEPT. 89

Page 61: 14cux Fuel Injection

KAl~bJr

ROVER “*’ FUEL INIECTION SYSTEM 119 1I I

RESULTS - Check cables and units shown in bold

Voltmeter reading of 12 volts -Proceed to Test 31

TEST PROCEDURE

29. Check operation ot compressor clutch relay

NOTE: Select air conditioning position, Incorrect reading of zero voltsthermostat cold, and tan speed I, II, or Ill Proceed to Test 30

30. Fault diagnosis - compressor clutch relay r reading of 12 volts -

NOTEz Select air conditioning position,thermostat cold, and tan speed I, II or Ill

KEY:1. Compressor clutch relay2. Compressor clutch3. High pressure switch4. Thermostat

Continued

ADDITION: SEPT. 88 / REVISED: DEC. 88 61 ‘.’‘.y:...

Page 62: 14cux Fuel Injection

1191 FUEL INJECTION SYSTEM 1989 ;;^d;&

EST PROCEDURE

I l . Check heated front screen input

NOTE: Engine running, heated front screen Incorrect reading of zero voltsswitched ‘ON’ Check:

KEY:1. Oil pressure switch2. Front screen timer unit3. Front screen switch

rEST PROCEDURE

12. Check operation of condenser fan output

Disconnect coolant temperature sensor and fueltemperature sensor and bridge plug connectors

NOTE: Switch ignition ‘ON’ for 5 seconds, switchignition ‘OFF’

The fan timer will operate the fans forapproximately 10 minutes unless it is disconnected

KEY:1. Condenser fan timer2. Condenser fan relay

RR2660E

RESULTS - Check cables and units shown in bold I

Voltmeter reading of 12 volts -Proceed to Test 32

RESULTS - Check cables and units shown in bold

Voltmeter reading of 12 volts - end of tests

Voltmeter reading of zero voltsProceed lo Test 33

62 ADDITION: SEPT. 88 / REVISED: DEC. 88

Page 63: 14cux Fuel Injection

. .

.‘;.

.L.,

::.,’X

FUEL INJECTION SYSTEM 119 1

‘EST PROCEDURE

13. Fault diagnosis - condenser fan outpul

RESULTS - Check cables and units shown in bold

Voltmeter reading of 12 volts -Suspect ECU

KEY:1. Condenser fan timer2. Condenser fan relay3. Fuses Al and A24. Condenser fans

Incorrect readingCheck:

\ 1 /-a-0’ I ’

IGNITION ON

IR 2676E

After completing the tests with either the ‘Diagnostic’ equipment or multi-meter, re-test the vehicle to ensurethe faults have been rectified. If faults still persist, recheck using the Lucas diagnostic equipment.

,

ADDITION: SEPT. 88 I REVISED: SEPT. 90 63

Page 64: 14cux Fuel Injection

1 2 BA6

ov-

E

I

BGW G 4

I N .+

l-

3

---BN BRt BI 9 I

- - -

RWOlOE

,, ,. :’Condenser fan circuit diagram RR2610E

1. 12V from EFI main relay.2. Condenser fan timer unit.

Condenser fans/Condenser fan timer

Check operation

3. Fan relay. 1.4. 12V battery feed. 2.5. Trigger, from ECU.6. 12V from fan relay. 3.7. Fuse Al-20 amp.8. Fuse A2-20 amp.9. Fan motors 4.

5.

6.

64 ADDITION: SEPT. 88 / REVISED: SEPT. 90

7.

Start engine.Move air con/heater control to air conditioningposition.C h e c k c o n d e n s e r f a n s , i f w o r k i n g t h econdenser fan relay and wiring to the fans isfunctioning.If not working check fuses Al and A2, and thevoltage between connections 86 on fan relayand earth. If 12 volts is not present, checkwiring back to air con switch.If 12 volts is present, but fans NOT working,short out connections 30 and 87 on fan relay.If fans work fit new relay. If fans NOT working,check supply to fan relay from main harness.Apply a 12 volt supply for at least two secondsto connect ion 5 on fan t imer wi th in S IXSECONDS of switching engin off. Thecondenser fans should run for 9.f minutes +0.5 minutes, and switch off.If the fans do not work after applying voltageto timer, short out connections 4 and 8 on fantimer, if fans work fit new fan timer. If fans donot work, check wiring.

Page 65: 14cux Fuel Injection

KANbtROVER lg8’ FUEL INJECTION SYSTEM

OVERHAUL THROlTLE LEVERS AND THROTTLE 11. Remove the large hose from the neck of theVALVE - 3.9 V8 Model plenum chamber.

12. D isconnect the mult i -p lug to the thrott lepotentiometer.Preparation, remove, overhaul and refit

Preparation

1.2.

3.

4.

8.

9.

10.

Disconnect the battery negative terminal.Disconnect the electrical multi-plug from thebypass air valve (stepper motor).Disconnect the small vacuum hose at the rearof the plenum chamber, located below thebypass air valve.To assist re-assembly mark an identificationline on the throttle cable outer coveringdirectly behind the adjustment thumb wheelbefore disconnecting the throttle cable fromthe throttle lever.Remove the cotter pin and clevis pin securingthe throttle cable to the lever.Carefully pry the adjustment thumb wheelfrom the throttle bracket. Lay the cable aside.Release the retaining clip from the kick downcable and remove the clevis pin.To assist re-assembly apply adhesive tapebehind the rear adjustment nut on the kickdown cable outer sleeve to prevent the nutmoving out of position.Release the front lock nut and remove it fromthe outer sleeve to enable the cable to beremoved from the throttle bracket. Lay thecable aside.Remove the vacuum hose from the cruisecontrol actuator.

13. Remove the PCV breather hose.14. Disconnect the two coolant hoses in turn and

immediately plug the end of each hose toprevent excessive loss of coolant. Identifyeach hose for re-assembly.

15. Remove the distributor vacuum hose.

16. Release the two screws and remove thepotentiometer.

ADDITION: SEPT. 88 65

Page 66: 14cux Fuel Injection

7 6

RR2400E

KEY

I. Spherical bearing2. Retaining clips (2)3. Countershaft assembly4. Overtravel spring5. Throttle spindle nut6. Throttle return spring (2)7. Tab washer8. Throttle stop lever9. Throttle bracket assembly

10. Pop rivets (2)

Remove throttle lever assembly

17.

18.

19.

20.

66

Remove the six screws securing the plenumchamber to the ram housing. Li f t off theplenum chamber.Remove the hose from the air bypass valvehousing and plenum chamber air inlet pipe.Unclip the cruise control actuator link. Whileholding the throttle valve fully open releasethe l ink from the countershaft assembly.Carefully return the lever assembly to theclosed throttle position.Release the tension on the inboard throttlereturn spring and slide the spring along thecountershaft assembly to give access to thethrottle shaft nut.

21.22.

23.

Bend back the the tabs of the lock washer.While holding the throttle stop lever in theclosed position, release the nut until it is freeof the throttle valve shaft.Release the tension on the outboard throttlereturn spring.

24. Unhook and remove the over-travel spring.

ADDITION: SEPT. 88

‘.. . .

Page 67: 14cux Fuel Injection

:

.t

,,,::

FUEL INJECTION SYSTEM

25. Remove the three bolts securing the throttlebracket to the plenum chamber and withdrawthe bracket assembly.

26. Remove the tab washer and throttle stop leverfrom the throttle valve shaft.

Inspect and overhaul throttle lever assembly

31.

32.

Pre-grease a new bush with Admax L3 orEnergrease LS3 assemble the bush into thebearing retaining plates and pop-rivet theassembly to the throttle bracket with two 4.7mm (3116 in) diameter domed head rivets 9mm (0.361 in) long.Examine the bearing surface of thecountershaft assembly. If worn f i t a newassembly, otherwise wind the throttle returnspring off the levers.

32

RR2308E27.

28.

29.

30.

Remove the two retaining clips from eitherside of the spherical bearing.Remove the countershaft assembly from thebearing.If the spherical bush appears to be worn,dismantle as follows. Using a 4,7 mm (3116 in)diameter drill, drill out the two pop rivetssecuring the spherical bearing to the throttlebracket assembly.Split the bearing assembly and discard thebearing bush.

-RR2307E ‘9

:

33. Wind a new spring onto the countershaftassembly noting that the small hooked end ofthe spring is wound on first.

RR2309E

’ .

3 4 . P r e - g r e a s e t h e s h a f t w i t h Admax L 3 o rEnergrease LS3 and f i t the countershaf tassembly to the spherical bearing and securewith the two clips.

35. Examine the throttle stop lever ior wear, fit anew lever if necessary. ’

Continued

ADDITION: SEPT. 88 67

Page 68: 14cux Fuel Injection

.’

,

Inspect and overhaul throttle valve

3 6 .

3 7 .

Examine the throttle valve shaft for excessivewear between the bearing bushes in theplenum chamber and the shaft. A smalla m o u n t of clearance is permiss ib le . I fexcessive wear is evident fit new shaft andbushes as follows.Remove the two split screws securing thethrottle valve disc and withdraw the disc,taking care not to damage the shaft.

m

FIR24iIOE KQ I-

38. Remove the shaft and air seal from the plenumchamber.

RR2401E

39. Using a suitable drift, drive out the bushestaking care not damage the bores in theplenum chamber.

40. Press in new bushes until they are flush withthe throttle valve bore.

I 8I

RR2402E

4 1 .

4 2 .

4 3 .

Fit the throttle valve shaft and disc, secure inposition with the two split screws. Do not fullytighten the screws at this stage.Rotate the throttle shaft 360” once or twice tocentralise the disc in the bore. Tighten thetwo screws.

.‘(,

Rotate the shaft unti l the spli t end of thescrews are accessible. Using the blade of ascrew driver spread the split to secure thescrews in the shaft.

RR2409E

44. Pre-grease a new air seal with Admax L3 orEnergrease LS3. Fit the seal pushing it downthe shaft and into the counterbore until theseal is 6.0 mm (0.236 in) below the face of theplenum chamber.

J

CAUTION: Ensure that the bushes do notprotrude into the bore as they will interferewi th the movement of the throt t le va lvedisc.

. .

6 8 ADDITION: SEPT. 88

Page 69: 14cux Fuel Injection

FUEL INJECTION SYSTEM

Assemble throttle levers and bracket

45.

46.

47.

40.

49.

50.

51.

52

Fit the stop lever to the throttle valve shaftfollowed by a new tab washer and secure withthe interconnecting nut.Holding the stop lever on its stop, tighten theinterconnecting nut securely and bend overthe tabs of the tab washer to lock the nut inposition.Fit the inboard throttle return spring notingthat the small hooked end of the spring isnearest the plenum chamber.Locate the hooked end of the inboard springon the stop lever and wind up the straight endone full turn and anchor it in the appropriateslot.Fit the countershaft to the interconnecting nutof the throttle valve shaft.Fit the throttle bracket assembly and securewith the three retaining bolts.Ensuring that the hooked end of the outboardspring is anchored by the lever, wind thespring up one full turn and locate the free endin its appropriate slot.Fit the over-travel spring.Lightly grease the throttle return and over-travelsprings with Admax L3 or Energrease LS3.

50 46 48

NOTE: If new throttle levers have been fitted theminimum throttle setting of the disc must bechecked to ensure that it is SO” to the bore.

53.

54.

Using a depth vernier or depth micrometerfrom the mouth of the bore check the topand bottom of the valve disc. The disc mustbe within 0.5 mm (0.019 in) total indicatorreading across the full diameter of the disc.If the throttle disc is out of limits adjust thesmall set screw below the stop lever. Accessto the screw is gained from the bottom of theplenum chamber neck adjacent to the throttlelevers support bracket.

Refitting

55.

56.

Reconnect and adjust the cruise controlactuator link. (See cruise control-actuator linksetting)Clean any previous sealant from the joint faceof the plenum chamber and ram housing.Apply ‘Hylomar’ sealant to the faces and refitthe plenum chamber. Tighten the bolts to thecorrect torque value-see section 06.

57. Reverse the remaining preparation instructions.

ADDITEON: SEPT. 88 / REVISED: MARCH SO 69.

:,

Page 70: 14cux Fuel Injection

ELECTRONIC FUEL INJECTION-RELAYS ELECTRONIC CONTROL UNIT (ECU)-14 CU

Incorporated in the fuel injection electrical systemare two relays which are located beneath the frontright hand seat adjacent to the cruise control relayand emission maintenance reminder. Access to therelays is gained through the opening at the bottomof the seat when the seat is in its fully forwardposition on the seat slides.

1. Fuel pump relay (mounted on a blue terminalblock).

2. Main relay (mounted on a black terminalblock).

3. Diagnostic plug.

4. Condenser fan timer unit.

RR2555E

Remove and refit

Removing

1. Disconnect the battery negative terminal.2. Pull the relay(s) from the terminal block(s).

Refitting

3. Reverse the removal procedure.

70 ADDITION: SEPT. 88 / REVISED: MARCH 90

NOTE: The ECU is not a serviceable item. In theevent of a unit failure the ECU must be replaced.

Remove and refit

Removing

1.

2.

3.4.5.

6.

7

Remove the front and side seat base trim ofthe front right hand seat.Adjust the seat to its most rearward positionand raise the seat cushion height to allowaccess to the ECU fixings.Disconnect the battery negative terminal.Release the ECU plug retaining clip.Maneuver the f ront o f the p lug ( in thedirection of the bold arrow) and detach theother end of the plug from the retaining peg. .Release the two screws securing the ECU tothe mounting bracket.Withdraw the ECU from the spring clip andremove it from the vehicle.

,‘/

RR2667S

Refitting8. Refit the ECU securely in the spring clip and fit

and tighten the two screws.9. Reconnect the ECU harness plug. Ensure that

the plug is pushed firmly into its location andthat the retaining clip secures the plug inposition.

10. Remove remaining removal procedure.

Page 71: 14cux Fuel Injection

.., _. . --R O V E R lyy”

1

:. ”,,

RR2

2628294

2.3106

21lV”B I. I II, YB I ’ WG-30

125

27

91s

36301916

2253520

332

72239

17

955E

FUEL INFECTION - Circuit Diagram - 1990/91 model vear1. 40 -way connector to Electronic Control Unit

(ECU).2. Lambda sensor (left side - bank A).3. Lambda sensor (right side - bank 8).4. By-pass air valve (stepper motor) (fast idle).5. Lambda sensor screened ground.6. Fuse C4 - main fuse panel.7. Inertia switch.8. Fuel pump.9. Ignition switch.

10. Speed transducer (road speed input).I l . Neutral switch (automatic gearbox) ( load

input).12. Main cable connector.13. Battery.14. Diagnostic plug.15. In-line resistor.16. Coil/-ve (engine RPM input).1 i. Coolant temperature thermistor (sensor)

(input).

18. Fuel temperature thermistor (sensor) (input).19. Throttle potentiometer.20. Air flow sensor.21. Fuel pump relay.22. Main relay.23. Injectors-l to 8.24. Pick-up point E.F.I. warning symbol (instrument

binnacle).25. Heated front screen sense.26. Purge control valve.27. 12\’ from fan relay.28. Air conditioning output [email protected]. Air conditioning load input.30. Fan relay feed.31. Tune resistor (early vehicles).32. Heater/air con. cable connector.33. Condenser fan timer control.34. Fault display input.

= = = Denotes screened ground.

NOTE: Reference to left and right side is made when viewing the vehicle from the rear.

ADDITION: SEPT. 89/REVISED: SEPT. 90 71

Page 72: 14cux Fuel Injection

FUEL INJECTION SYSTEM1990 KANCltROVER

ELECTRONIC FUEL INJECTION-LUCAS 14CUX SYSTEM

1990 model year vehicles have an enhanced fuelinjection system, using a Lucas 14CUX electroniccontrol unit, The system is a development of the14Cu sytem introduced on 3.9 litre vehicles.The system works in the same way, newcomponents being a tune select resistor and a faultcode display unit.

TUNE SELECT RESISTOR - RR281 1M

Rd28llM

The 14CUX system is used in various markets, but acommon ECU is used. To suit individual marketrequirements a tune select resistor is connectedacross pins 5 and 27 of the ECU.It is located adjacent to the ECU, and strapped tothe EFI cable assembly. The value of the resistor isdependent on the market application.

NOTE: For USA market models the resistor valueis 3900 Ohms, wire colour, white.

NOTE: Vehicles after VIN No 451518 are fittedwith a new ECU, Part No. PRC 8747 to replacePRC 7081. This ECU no longer requires the tuneselect resistor, which is therefore deleted. Faultcode 21 is no longer stored by the ECU.

17EM FAULT CODE DISPLAY UNIT - RR2814h-l

1990 model year vehicles have a fault code displayunit which is located underneath the right handfront seat, adjacent to the EFI ECU. The unit willdisplay the relevant fault code, in addition to theEFI warning light being illuminated.

NOTE: Fault code 59 will NOT be indicated bythe EFI warning light.

Recommended equipment

The diagnostic equipment for checking out the14CuX system is the same as that used for 14CU,with the addition of two new memory cards forHand Held Tester.

14CUX Memory cards, Lucas Part Number:- 606 01 379.

CONTINUITY TEST PROCEDURE

NOTE: The continuity test procedure for 14CUXsystems is similar to that for 14CU. Note theaddition of the tune select resistor test and thedeletion of Test 28, which does not apply to14CUX systems.

,

7 2 ADDITION: SEPT. 89iREVISED: SEPT. 90

(’

‘.‘:. rt". 'iv'. .

I.>...' ...a.;“.i

. . . . t

” ;._.,.

Page 73: 14cux Fuel Injection

K"i;;‘;ir 1990 FUEL INJECTION SYSTEM 119 1

.

TESTING CONNECTIONS TO 40 WAY CONNECTOR

Release the ECU plug reta ining c l ip andremove the plug from the ECU. Access isgained by removing the front seat base trim ofthe right hand front seat.Remove the plug shroud and manoeuver ita long the harness unt i l there is enoughclearance to enable meter probes to beinserted into the back of the plug.There are six pin numbers 1, 13, 14, 27, 28and 40 moulded onto the rear of the plug asshown in the illustration below, for clarity theelectrical leads have been omitted.

27

2 8 4 0

Pins 1 to 13 bottom row.Pins 14 to 27 centre row.Pins 28 to 40 top row.

-14

PIN Nos. CABLE COLOUR

1. Red/green2. Brown/orange3. Yellow4. Blak5. Grey/Black6. Yellow7. Green/blue8. Purple/yellow9. White/light green

10. Black/yellow11, Yellow/white12. Blue/redI 3. Yellow/blue14. Black15. Brown16. Blue/purple17. Grey/yellow18. White/pink79. White/grey20. Red21. Yellow/black22. Blue/red23. Blue24. Blue25. Red/black26. Green/white27. Black/grey28. Bluelgrey29. Orange30. Pink31. Black/green32. Creyhvhite33. BlackIgrey34. Orange/black35. Blue/green36. Black/green37. Not used38. Brown/pink39. White/black40. Black

The last colour denotes the wire tracer colour

.

ADDITION: SEPT. 89!REVISED: SEPT. 90 73

Page 74: 14cux Fuel Injection

‘.,

.‘....+

_: 3

: ‘.,,

Tune select resistor test

lt is recommended that this test is carried out NOTE: This test is not required on vehicles afterbefore Test 1. of Continuity Test Procedure, Section VIN No 451518, which are no longer fitted with a19, page 44. tune select resistor.

FUNE SELECT RESISTOR TESTKEY 1) Tune select resistor

Description of fault codes

The fault codes are listed in order of priority. Wheremore than one fault exists, clearing the first faultcode will permit the next code to be displayed.

NOTE: Fault code 02 will show if the ECU hasjust been reconnected. Switch on ignition toclear the display.

Clearing fault code display

It is necessary to clear the code displayed when thefault has been rectified, and to access any furtherfault codes that may exist. Clear the fault codedisplayed using the following procedure:

1. Switch On ignition.2. Disconnect serial link mating plug, wait 5

seconds, reconnect.3. Switch OFF ignition, wait for main relay to

drop out.4. Switch ON ignition. The display should now

reset. If no other faults exist, and the originalfault has been rectified, the display will beblank.

5. If multiple faults exist repeat Steps 1. to 4. aseach fault is cleared the code will change,until all faults are cleared. The display will nowbe blank.

74

Code 29 - ECU MEMORY CHECK - If this fault isdetected, all other faults are unreliable and musttherefore be ignored.

‘I ,,

Proceed as follows:

1. Leave battery connected2. Switch ignition off3. Wait for approximately 5 seconds4. Disconnect ECU plug5. Re-connect ECU plug6. Switch ignition on and check display unit.

NOTE: If fault code 29 is detected again,substitute ECU and restart test sequence.

Code 44 - LAMBDA SENSOR A i left bankCode 45 - LAMBDA SENSOR B - right bank

If one of these fault codes is displayed check thewiring to that particular lambda sensor.

If both codes are displayed, the volfage supply tothe heater coils of the sensors must be checked.Refer to Test 26, continuity test procedure.

Code 25 - IGNITION MISFIRE - This code indicates . . . . .that an ignition system misfire has been detected. ICodes 40 or 50 indicate on which bank the misfirehas occured. ..’ . .,,

1.,.

ADDITION: SEPT. 89/REVISED: SEPT. 90

Page 75: 14cux Fuel Injection

FUEL INJECTION SYSTEM

Code 40 - MISFIRE BANK A - left bankCode 50 - MISFIRE BANK B - right bank

If both fau l t codes are d isp layed check thefollowing components commom to both banks:

Distributor capRotor armCoilElectrical connectionsPick-up (air gap)AmplifierInjectors - if code 34 or 36 displayed.

If either fault code 40 or 50 is displayed checkcomponents applicable to the particular bank thatthe misfire has occured on:

.

Spark plugsHT leadsDistributor capInjectors - if code 34 bank A or 36 bank 6displayed.

:.:.y. : .:.:$c.

Code 12 - AIRFLOW METER - Refer to Test 19,continuity test procedure.

Code 21 - FUEL TUNE SELECT - Identifies that thetune select resistor is open circuit - Refer to tuneselect resistor test.

Code 34 - INJECTOR BANK A - The display willindicate if the injector/s are causing the engine torun rich or lean.

If the bank is running rich, check for:-- faulty injector wiring and connectors- stuck open injectors

If the bank is running lean, check for:-- faulty injector wiring and connectors- blocked injectors

Code 36 - INjECTOR BANK B - As code 34 exceptrelevant to bank A injectors.

Code 14 - COOLANT THERMISTOR - Refer to Test14, continuity test procedure.

Code 17 - THROlTLE POTENTIOMETER - Refer toTest 17, continuity test procedure.

Code 18 - THROlTLE POTENTIOMETER inputhigh/AIRFLOW METER - low. - Refer to Tests 17,18 and 19 of the continuity test procedure

Code 19 - THROTTLE POTENTIOMETER input low/AIRFLOW METER - high. - Refer to Tests 17, 18and 19 of the continuity test procedure

Code 88 - PURGE VALVE LEAK - Refer to Test 9and 10 of the continuity test procedure.

Code 28 - AIR LEAK - Check for air leaks in thefollowing areas.Hose, air flow meter to plenumBreather system hoses to plenumBrake servo hoseVacuum reservoir hose (fresh air solenoid)Distributor vacuum advanceHose, purge valve to plenumInjector sealsJoint - By pass air valve to plenum

- Plenum chamber to ram housing- Ram housing to inlet manifold- Inlet manifold to cylinder head

By pass air valve hose

Code 23 - FUEL SUPPLY - Check fuel systempressure, Test 20 of the continuity test procedure.

Code 48 - STEPPER MOTOR - Check base idlespeed - see setting procedure. - Refer to Tests 15and 16 of the continuity test procedure. Checkroad speed sensor - Refer to Test 25 of thecontinuity test procedure.

Code 68 - ROAD SPEED SENSOR - Refer to Test25 of the continuity test procedure.

Code 69 - GEARSWITCH - Refer to Test 24 of thecontinuity test procedure.

Code 59 - GROUP FAULTS 23/28 - This indicatesthat a fault has been registered that is caused bythe fuel supply or an air leak but the exact faultcannot be identified. Check all items outlined undercode 23 and 28.

Code 15 - FUEL THERMISTOR - Refer to Test 13 ofthe continuity test procedure.

ADDITION: SEPT. 89/REVISED: SEPT. 90

Page 76: 14cux Fuel Injection

;

,: ;

..,..’ :

:,:

1.i :

“. ,: ,:

i.‘.’X

.’ I

.

,:. .‘,;. : :.

1990 NINclcROVER

BASE IDLE SPEED SETTING

NOTE: the base idle speed is set at the factory. Itshould not require further adjustment unless theplenum chamber is changed. The adjustmentscrew is sealed with a plug to preventunauthorised alteration. Check the ignitiontiming before attempting the followingprocedure, since this will affect the idle speed.

Equipment required

Two blanking hoses. It is recommended that theseare manufactured using a new air by-pass valvehose - Pari No.ETC7874. Cut two equal pieces9Omm (3 l/2 inches) long from the hose and sealone end of each, using 13mm (l/2 inch) diameterbar. A suitable clamp can be used to ensure an airtight seal

Checking procedure

Drive the vehicle for at least two miles untilthe engine and transmission are hot. Switchoff the engine.Check that all electrical loads are off includingair conditioning.Remove the air by-pass valve hose.Fit the blanking hoses to both the plenumchamber and the air by-pass valve. Ensure thehoses are securely fitted to prevent air leaks.Note that the throttle cable and cruise controlactuator have been omitted from theillustration for clarity.

5. Start the engine and check that the idle speedis within the limits specified in Section 05 -Engine Tuning Data.

Adjusting base idle speed

6. Remove the tamper proof plug that protectsthe idle speed screw. Drill the plug and inserta self tapping screw to enable the plug toextracted.

RR2953E

7.

8.

Start the engine, and using a suitable Allenkey, adjust the idle screw clockwise todecrease or counter-clockwise to increae theidle speed.Check fault code display, and clear thememory - see ‘Clearing fault code display’ -section 19, page 74.

76 ADDITION: SEPT. 89:

Page 77: 14cux Fuel Injection

K”i;;l;i 1990 FUEL INJECTION SYSTEM 119 1

:

,::

.,. ,.

FUEL SYSTEM 1991 MODEL YEAR..

A revised fuel sytem is fitted to 1991 model yearvehicles. The major change is the fitting of a plasticfuel tank with improved breather system. Theremote expansion tank is now deleted.A further improvement is the fitting of a combinedfuel pump and sender unit. A panel in the floor ofthe vehicle permits access to the fuel pump/senderunit

FUEL PUMP/SENDER UNIT

WARNING: Ensure that the Fuel Handl ingPrecautions given in Section 01 - Introductionregarding fuel handling are strictly adhered towhen carrying out the following instructions.

:;. ::‘.‘*‘a’.%’

CAUTION: Before disconnecting any part of thefuel system, it is imperative that all dust, dirtand debris is removed from around thecomponents to prevent ingress of foreign matterinto the fuel system.

Special Tool - LST131, wrench - pump retainingring

- LST 144 -‘Speedfit’ disconnector

Remove and refit

Removing

1.2.3.

4.

5.

Depressurise the fuel system.Disconnect battery negative lead.Syphon at least 9 litres (2 gallons) of fuel fromthe fuel tank using a suitable container thatcan be sealed afterwards.Remove carpet from loadspace f loor andtailgate.Fold back the sound insulation to reveal theaccess panel.

6. Remove the securing screws and detach theaccess panel from the floor.

7. Disconnect the electrical connections at themulti-plug.

8. Remove the insulation sealant from around theground lead, and disconnect the ground lead.

9. Disconnect the two fuel line unions from thefuel pump.

10. Using Special Tool No. LST131, remove pumpassembly retaining ring and withdraw thepump from the fuel tank.

WARNING: A quantity of fuel will be retained inthe body of the unit, care must be taken toprevent fuel spillage when the unit is removed.

ADDITION: SEPT. 89 77

Page 78: 14cux Fuel Injection

’ FUEL INJECTION SYSTEM

Refitting

11.

12.13.14.

15.

16.

17.

18.

19.

Insert the fuel pump into the tank. Fit theretaining ring and tighten to a torque of 45-50Nm (34-37 Ibf ft).Connect the fuel lines to the pump.Connect the electrical leads at the multi-plug.Connect the ground lead to the pump andinsulate with suitable sealant.When the fuel system has been reassembledcheck all fuel pipes, sealing rings and hoseconnections are secure.Run the engine to check for fuel leaks beforefinal assembly.Inspect the access panel seal, fit a new seal ifnecessary.Fit the access panel and secure to the floorwith the screws.Reverse operations 4 - 5 to refit the soundinsulation and carpet.

FUEL TANK

WARNING: Ensure that the Fuel HandlingPrecautions given in Section 01 - Introductionregarding fuel handling are strictly adhered towhen carrying out the following instructions.

CAUTION: Before disconnecting any part of thefuel system, it is imperative that all dust, dirtand debris is removed from around thecomponents to prevent ingress of foreign matterinto the fuel system.

Remove and refit

Removing

1.

2.

Depressurise fuel system. Disconnect batterynegative lead.Syphon the fuel tank into a suitable containerthat can be sealed afterwards.ENSURE THAT THE TANK IS DRAINEDCOMPLflELY. (refer to Warning concerningfuel vapor and spillage at start of thisprocedure).Remove carpet from loadspace floor andtailgate.Fold back the sound insulation to reveal theaccess panel.Remove the securing screws and detach theaccess panel from the floor.Disconnect the electrical connections at themulti-plug.

NOTE: To disconnect the ‘speedfit’ connector,forked end into the two slots of the connectoras shown in the illustation above. Press down onthe collet and simultaneously pull t&e pipe fromthe connector. Special tool LST 144 is availablefor this operation.

78 ADDITION: SEPT. 89

Remove the insulation sealant from around theground lead, and disconnect the ground lead.Disconnect the two fuel line unions from thefuel pump.Working underneath the vehicle, remove therear anti-roil bar straps, and allow the bar toswing down clear of the tank.

1'3 11 16RR2962E

10.

11.

12.

Remove the tank filler and vent hoses at thefuel tank.Remove the nut and bolt securing the righthand side of the fuel tank strap.Disconnect the WdpOratiVe control pipe at thegreen end of the ‘speedfit’ connector.

Page 79: 14cux Fuel Injection

:

,_ :

‘.’ .,

.’

:. >,

yo;;; 1990 FUEL INJECTION SYSTEM

13. Remove the back two bolts and nut platessecuring the fuel tank cradle.

14. Remove the front nuts, bolts and washers, andremove the fuel tank cradle.

15. With the aid of an assistant, tilt the right handside of the tank upwards and manouver thetank through the chassis to remove.

Refitting16. Reverse the removal procedure, ensuring that

the sealing ring, fuel pipe and hoseconnections are secure.

17. Run the engine and recheck all connectionsto ensure no fuel leaks exist. Reverse theremaining removal procedure.

FUEL FILTER

Remove and refit

WARNING: ENSURE THAT THE FUEL HANDLINGPRECAUTIONS GIVEN IN SECTION 01 -INTRODUCTION REGARDING FUEL HANDLINGARE STRICTLY ADHERED TO WHEN CARRYINGOUT THE FOLLOWING INSTRUCTIONS.

WARNING: THE SPILLING OF FUEL ISUNAVOIDABLE DURING THIS OPERATION.ENSURE THAT ALL NECESSARY PRECAUTIONSARE TAKEN TO PREVENT FIRE AND EXPLOSION.

Removing

1. Depressurise the fuel system.2. The fuel filter is located on the right-hand

chassis side member forward of the fuel tankfiller neck. Access to the filter is gainedthrough the right-hand rear wheel arch.

Clamp the inlet and outlet hoses to preventthe minimum of fuel spillage whendisconnecting the hoses.Loosen the two fuel line unions and removethe hoses from the filter canister.Release the single nut and bolt securing thefilter and clamp and remove the filter.

,- -\ 7 “

RR2966E

Refitting

6.

7.8.

9.

10.

Fit a new filter observing the direction of flowarrow on the canister.Tighten the single nut and bolt.Fit the inlet and outlet hoses. Tighten theunions to a torque of 20-25 ft lb(27-34Nm).Refit the fuel pump relay, reconnect thebattery. Recode the radio.Start the engine and inspect for fuel leaksaround the hose connections.

ADDITION: SEPT. 89 79

Page 80: 14cux Fuel Injection

:

,,:..

..’.‘.’

..I ::

‘, ,. ,;

.’

:..

X

‘.

1191 FUEL INJECTION SYSTEM

FUEL FILLER FLAP RELEASE BUTTON

The fuel filler flap is no longer part of the centrallocking system on 1991 model year vehicles. Thefiller flap is permanently locked. To release the flappress the button situated on the steering columnshroud. On closing, the filler flap will be lockedautomatically. Note that the release button will onlywork with ignition switched OFF.

Remove and refit

Removing

1. Disconnect the battery negative lead.2. Carefully pry the release button from the

steering column shroud.

RR2031M

3. Remove the release button from the shroudand disconnect the two wiring connectors.Ensure that the wires protrude through theshroud to facilitate reassembly.

Refitting

4. Reverse the removal procedure. Recode theradio.

FUEL FILLER FLAP RELEASE ACTUATOR

Remove and refit

Removing

1. Ensure that the fuel filler flap is released.Disconnect the battery negative lead.

2 . Remove eight screws, and withdraw theclosure panel, situated in the right hand sideof the load space.

3. Release two screws and maneuver the actuatorclear of its mounting.

4. Disconnect the wiring plug.5. Withdraw the actuator.

RR2932M

Refitting

a0 ADDITION: SEPT. 89

6. Reverse the removal procedure. Recode theradio.

.: