RESTRAINT SYSTEMSECTION RSCONTENTSPRECAUTIONS AND PREPARATION............................2Supplemental Restraint System (SRS)AIR BAG ...................................................................2SEAT BELTS ...................................................................3Front Seat Belt.............................................................4Rear Seat Belt .............................................................5Seat Belt Inspection.....................................................6SUPPLEMENTAL RESTRAINT SYSTEM (SRS)............9Precautions for SRS AIR BAG Service....................9Special Service Tools ................................................10Description................................................................. 11Passenger air bag deactivation switch...................... 11SRS Component Parts Location ...............................12Maintenance Items ....................................................13Diagnosis Sensor Unit and Crash Zone Sensor .......14Removal And Installation ......................................14Air bag diagnosis sensor unit ...........................14Crash zone sensor ...........................................14Driver Air Bag Module and Spiral Cable ...................15Passenger Air Bag Module........................................18Passenger Air Bag Deactivation Switch....................20Passenger Air Bag Deactivation Switch LockCylinder......................................................................20Passenger Air Bag Deactivation Switch Indicator .....21Disposal of Air Bag Module.......................................22TROUBLE DIAGNOSES SupplementalRestraint System (SRS) ...............................................26Trouble Diagnosis Introduction..................................26How to Perform Trouble Diagnoses for Quickand Accurate Repair ..................................................29Schematic ..................................................................30Wiring Diagram SRS .............................................31Passenger Air Bag Deactivation Switch IndicatorOperation Check........................................................33SRS Operation Check ...............................................34Trouble Diagnoses with CONSULT.................35Trouble Diagnoses without CONSULT............44Trouble Diagnoses: AIR BAG Warning LampDoes Not Turn Off .....................................................48Trouble Diagnoses: AIR BAG Warning LampDoes Not Turn On .....................................................49Trouble Diagnoses: SRS Does Not EnterDiagnosis Mode Using Door Switch..........................50COLLISION DIAGNOSIS...............................................51When you read wiring diagrams:GRead GI section, HOW TO READ WIRING DIAGRAMS.GSee EL section, POWER SUPPLY ROUTING for power distribution circuit.Whenyouperformtroublediagnoses, readGI section, HOWTOFOLLOWFLOWCHARTINTROUBLEDIAGNOSES andHOWTOPERFORMEFFICIENTDIAGNOSISFOR AN ELECTRICAL INCIDENT.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSupplemental Restraint System (SRS)AIR BAGTheSupplemental Restraint SystemAIRBAG, usedalongwithaseat belt, helpstoreducetheriskorseverity of injury to the driver and front passenger in a frontal collision. The Supplemental Restraint Systemconsists of air bag modules (located in the center of the steering wheel and in the instrument panel on thepassenger side), a diagnosis sensor unit, a crash zone sensor, warning lamp, wiring harness and spiral cable.The vehicle is equipped with a passenger air bag deactivation switch. Because no rear seat exists where arear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that arear-facing child restraint can be used in the front passenger seat. The switch is located in the center of theinstrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag isenabled and could inflate in a frontal collision. When the switch is turned to the OFF position, the passengerair bag is disabled and will not inflate in a frontal collision. A passenger air bag OFF indicator on the instru-ment panel lights up when the passenger air bag is switched OFF. The driver air bag always remains enabledand is not affected by the passenger air bag deactivation switch.WARNING:GTo avoid rendering the SRS inoperative, which could increase the risk of personal injury or deathin the event of a collision which would result in air bag inflation, all maintenance should be per-formed by an authorized NISSAN dealer.GImproper maintenance, including incorrect removal and installation of the SRS, can lead to per-sonal injury caused by unintentional activation of the system.GDo not use electrical test equipment on any circuit related to the SRS unless instructed to in thisServiceManual. SRSwiringharnessesarecoveredwithyellowinsulationeitherjustbeforetheharness connectors or on the complete harness, for easy identification.GThe vehicle is equipped with a passenger air bag deactivation switch which can be operated bythe customer. When the passenger air bag is switched OFF, the passenger air bag is disabled andwill not inflate in a frontal collision. When the passenger air bag is switched ON, the passenger airbag is enabled and could inflate in a frontal collision. After SRS maintenance or repair, make surethe passenger air bag deactivation switch is in the same position (ON or OFF) as when the vehiclearrived for service.CAUTION:Certain systems and components, especially those related to OBD, may use a new style slide-lockingtype harness connector.For description and how to disconnect, refer to EL section, Description, HARNESS CONNECTOR.PRECAUTIONS AND PREPARATIONRS-2CAUTION:GDo not disassemble buckle or seat belt assembly.GReplace anchor bolts if they are deformed or worn out.GNever oil tongue and buckle.GIf anycomponent of seat belt assemblyisquestionable, donot repair. Replacetheseat beltassembly.GIf webbing is cut, frayed, or damaged, replace seat belt assembly.GWhen replacing seat belt assembly, use a genuine NISSAN seat belt assembly.GAfter any collision, inspect all seat belt assemblies, including retractors and other attached hard-ware.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSEAT BELTSRS-3Front Seat BeltARS319REMOVALRemove front seat. Refer to BT section (Front Seat, SEAT).1 Remove buckle.2 Remove floor anchor bolt.3 Remove adjuster cover and upper guide loop anchor bolt.For King Cab models, remove jump seat. Refer to BT section, (Rear Seat, SEAT).Remove rear pillar lower and upper garnishes.4 Remove guide plate.5 Remove two adjuster bolts and adjuster assembly.6 Remove retractor bolt and screw.7 Remove retractor.SEAT BELTSRS-4Rear Seat BeltARS320REMOVAL1 Remove underseat storage.2 Remove buckle.3 Remove seat belt anchor bolt.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSEAT BELTSRS-5Seat Belt InspectionAFTER A COLLISIONWARNING:Inspect all seat belt assembliesincludingretractorsandattachinghardwareafter anycollision.NISSANrecommendsthatallseatbeltassembliesinuseduringacollisionbereplacedunlessthecollision was minor and the belts show no damage and continue to operate properly. Failure to do socould result in serious personal injury in an accident. Seat belt assemblies not in use during a colli-sion should also be replaced if either damage or improper operation is noted.Replace any seat belt assembly if:GThe seat belt was in use at the time of a collision (except for minor collisions when the belts, retractorsand buckles show no damage and continue to operate properly).GThe seat belt was damaged in an accident (i.e. torn webbing, bent retractor or guide, etc.).GThe seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for dam-age or distortion and repair as necessary before installing a new seat belt assembly.PRELIMINARY CHECKS1. Check the seat belt warning lamp/chime for proper operation as follows:a. Switch ignition ON. The seat belt warning lamp should illuminate. Also, the seat belt warning chime shouldsound for about 7 seconds.b. Fasten drivers seat belt. The seat belt warning lamp should go out and the chime (if sounding) shouldstop.2. Check that the seat belt retractor, seat belt anchor and buckle bolts are securely attached.3. Check the shoulder seat belt guide and shoulder belt height adjuster for front seats. Ensure guide swiv-els freely and that belt lays flat and does not bind in guide. Ensure height adjuster operates properly andholds securely.ARS2224.Check retractor operation including:a.Fully extend the seat belt webbing and check for twists, tearsor other damage.b.Allow the seat belt to retract. Ensure that belt returns smoothlyandcompletelyintotheretractor. If theseat belt doesnotreturn smoothly, wipe the inside of the loops with a clean papercloth, etc. becausedirt built upintheloopsof theupperanchors can cause the seat belts to retract slowly.c.Fasten the seat belt. Pull firmly on belt and buckle to ensurebelt remains latched. Unfasten seat belt. Ensure belt releasesfreely and buckle button returns to original position.5.For non-retractable seat belts, check that the seat belts areaccessible. Check seat belt webbing for twists, tears or otherdamage. Fasten the seat belt. Pull firmly on belt and buckle toensure belt remains latched. Unfasten seat belts. Ensure beltreleases freely and buckle button returns to original position.6.Repeat stepsaboveasnecessarytochecktheother seatbelts.SEAT BELTSRS-6SEAT BELT RETRACTOR ON-VEHICLE CHECKEmergency Locking Retractors (ELR) and Automatic Locking Retractors (ALR)NOTE:All seat belt retractors are of the Emergency Locking (ELR) type. In an emergency (sudden stop) theretractor will lock and prevent the belt from extending any further. All outboard 3-point type seat beltretractors except the drivers seat belt also have an Automatic Locking (ALR) mode. The ALR mode(also called child restraint mode) is used when installing child seats in outboard seating positions. TheALR mode is activated when the seat belt is fully extended. When the belt is then retracted partially,the ALR mode automatically locks the seat belt in a specific position so the belt cannot be extendedany further. To cancel the ALR mode, allow the seat belt to fully wind back into the retractor.Check the seat belt retractors using the following test(s) to determine if a retractor assembly is operatingproperly.ELR function stationary checkGrasp the shoulder belt and pull forward quickly. The retractor should lock and prevent the belt from extend-ing further.ALR function stationary check1. Pull out entire length of seat belt from retractor until a click is heard.2. Retract the belt partially; a clicking noise should be heard as the belt retracts indicating retractor is in theautomatic locking (ALR) mode.3. Grasp the seat belt and try to pull out of retractor. Belt must lock and not extend further. If NG, replace theretractor assembly.4. Allow the entire length of belt to retract to cancel the automatic locking mode.ELR function moving check (all outboard seating positions)WARNING:Perform the following test in a safe, open area clear of other vehicles and obstructions (for example,a large, empty parking lot). Road surface must be paved and dry. DO NOT perform the following teston wet or gravel roads or on public streets and highways. This could result in an accident and seri-ous personal injury. The driver and passenger must be prepared to brace themselves in the event theretractor does not lock.1. Fasten drivers seat belt. Buckle a passenger into the seat for the belt that is to be tested.2. Proceed to the designated safe area.3. Drive the vehicle at approximately 16 km/h (10 MPH). Notify any passengers of a pending sudden stop.The driver and passenger must be prepared to brace themselves in the event the retractor does not lock.Apply brakes firmly and make a very hard stop.During stop, seat belts should lock and not extend. If the seat belt retractor assembly does not lock, performthe retractor off-vehicle check.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSEAT BELTSSeat Belt Inspection (Contd)RS-7SEAT BELT RETRACTOR OFF-VEHICLE CHECK1. Remove the seat belt retractor assembly.2. Slowly pull out belt while tilting the retractor assembly forward from the mounted position as shown in theillustration.15 degrees or less tilt: Belt can be pulled out.35 degrees or more tilt: Belt locks and cannot be pulled out.ARS223If NG, replace the retractor assembly.SEAT BELTSSeat Belt Inspection (Contd)RS-8Precautions for SRS AIR BAG ServiceG Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this ServiceManual. SRS wiring harnesses are covered with yellow insulation either just before the harness connec-tors or on the complete harness, for easy identification.G Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3minutes.For approximately 3 minutes after the cables are removed, it is stillpossible for the air bag to deploy.Therefore, do not work on any air bag system connectors or wires until at least 3 minutes have passed.G Air bag diagnosis sensor unit and crash zone sensor must always be installed with forward mark pointing toward the front of the vehicle for proper operation. Also check air bag diagnosis sensor unit andcrash zone sensor for cracks, deformities and rust before installation and replace if necessary.G The rotation of the spiral cable is limited. The spiral cable must be aligned in the neutral position. If thesteering gear must be removed, set the front wheels in the straight-ahead direction. Do not rotate thesteering column while the steering gear is removed to avoid damaging the spiral cable.G Handle air bag modules carefully. Always place them with the pad side facing upward.G Do not use old special bolts after removing any SRS parts; replace with new special bolts. Conduct self-diagnosis to check entire SRS for proper operation.G If front of vehicle is damaged in a collision, always check the crash zone sensor and the wiring harness.G After air bag inflates, the instrument panel assembly should be replaced if damaged.G After SRS maintenance or repair, make sure the passenger air bag deactivation switch is in the sameposition (ON or OFF) as when the vehicle arrived for service.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-9Special Service ToolsThe actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.Tool number(Kent-Moore No.)Tool nameDescriptionKV991072S0(J38381-KIT)Air bag deployment kitNT357Disposing of air bag moduleKV99106400(J38381)Deployment toolKV991065S0(J38381-30)Deployment tooladaptersARS269KV99105300(J41246)Air bag module bracketNT354Anchoring the air bag moduleHT61961000 andHT62152000 combined(J38219)*Special torx bitNT361Use for special bolts[TAMPER RESISTANT TORX (Size T50)]a: 3.5 (0.138) dia.b: 8.5 - 8.6 (0.335 - 0.339) dia.c: approx. 10 (0.39) sq.Unit: mm (in)*: Special tool or commercial equivalentSUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-10DescriptionThe air bag diagnosis sensor unit will deploy the air bags if the G-sensor and/or the crash zone sensor acti-vates simultaneously with the safing sensor while the ignition switch is ON. The passenger air bag does notdeploy when the passenger air bag deactivation switch is turned to the OFF position.Ignition Crash zone sensorAir bag diagnosis sensor unit Passenger air bagdeactivation switchpositionDriverair bagPassengerair bagG-sensorSafing sensorON ON ONON Deploy DeployOFF Deploy Not deployON ON ONON Deploy DeployOFF Deploy Not deployON ON ON ONON Deploy DeployOFF Deploy Not deployARS240Passenger air bag deactivation switchThevehicleisequippedwithapassenger air bagdeactivationswitch which can be operated by the customer. When the switch isturned to the ON position, the passenger air bag is enabled andcould inflate in a frontal collision. When the switch is turned to theOFF position, the passenger air bag is disabled and will not inflatein a frontal collision.After turning the ignition switch ON, a passenger air bag deactiva-tion switch indicator illuminates on the instrument panelfor bulbcheck. The indicator will stay lit if the passenger air bag deactiva-tion switch is in the OFF position. If the passenger air bag deacti-vation switch is in the ON position, the indicator will turn off afterabout 7 seconds.After SRS maintenance or repair, make sure the passenger air bagdeactivation switch is in the same position (ON or OFF) as whenthe vehicle arrived for service.IGN OFF ONPassenger air bagdeactivation switchpositionPassenger air bagdeactivation switchindicatorPassengerair bagdeploymentONTurns offwithin 7 secondsEnabledOFF Stays lit DisabledGIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-11Description (Contd)ARS311SRS Component Parts LocationARS312SUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-12SBF806EMaintenance Items1.Check AIR BAG warning lamp operationAfterturningtheignitionkeyON, AIRBAGwarninglampilluminates. TheAIRBAG warninglampwill turnoff afterabout 7 seconds if no malfunction is detected.If anyof thefollowingAIRBAG warninglampconditionsoccur, immediately check the air bag system. Refer to RS-34.GThe warning lamp does not illuminate when the ignition switchis turned ON.GThe warning lamp does not turn off about 7 seconds after theignition switch is turned ON.GThe warning lamp turns off about 7 seconds after the ignitionswitch is turned ON, but it turns on again or blinks.2.Visually check SRS componentsa.Crash zone sensorGCheck crash zone sensor to ensure the forward mark facesthe front of the vehicle.GCheck body and sensor bracket for deformities and rust.GCheck sensor case for dents, cracks, deformities and rust.GCheck sensor harness for binding, connector for damage andterminals for deformities.b.Air bag diagnosis sensor unitGCheckairbagdiagnosissensorunit andbracket fordents,cracks and deformities.GCheck connectors for damage and terminals for deformities.c.Air bag modules, steering wheel and instrument panelGRemovedriver air bagmodulefromsteeringwheel. Checkharness cover and connectors for damage, terminals fordeformities, and harness for binding.GInstall driver air bag module in steering wheel to check fit oralignment with the wheel.GCheck steering wheel for excessive free play.GRemove passenger air bag module. Check harness cover andconnectors for damage, terminals for deformities, and harnessfor binding. Check the bracket for deformities and rust.GInstall passenger air bag module in instrument panel to checkfit or alignment with the instrument panel.d.Spiral cableGCheck spiral cable for dents, cracks, and deformities.GCheck connectors and protective tape for damage.GCheck steering wheel for noise, binding and heavy operation.e.Passenger air bag deactivation switchGCheck passenger air bag deactivation switch for damage.GCheck harness for binding, connector for damage and termi-nals for deformities.f.Main harness and air bag harnessGCheck connectors for poor connections, damage, and termi-nals for deformities.GCheck harnesses for binding, chafing and cuts.CAUTION:Replace previously used special bolts with new ones.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-13Diagnosis Sensor Unit and Crash Zone SensorCAUTION:GBefore servicing SRS, turn the ignition switch OFF, disconnect both battery cables and wait at least3 minutes.GThe special bolts are coated with bonding agent while the other bolt is for ground. Do not use oldbolts after removal; replace with new coated bolts.GCheck air bag diagnosis sensor unit for proper installation. Make sure that there are no deformities,dents, cracks or rust. If there are any visible signs of damage, replace with a new one.GCheck air bag diagnosis sensor unit brackets to ensure they are free of deformities and rust.GReplace air bag diagnosis sensor unit if it has been dropped or sustained an impact.GCheck crash zone sensor for proper installation. Make sure that there are no deformities, dents,cracks or rust. If there are any visible signs of damage, replace the crash zone sensor.GCheck crash zone sensor bracket to ensure that it is free of deformities and rust.ARS307REMOVAL AND INSTALLATIONAir bag diagnosis sensor unit1.Disconnect driver and passenger air bag module connectors.2.Removeconsolebox. Refer toBTsection(INSTRUMENTPANEL).3.Disconnect air bag diagnosis sensor unit connector.4.Remove bolts from air bag diagnosis sensor unit. Use TAMPERRESISTANT TORX (Size T50) to remove special bolts.5.Remove the air bag diagnosis sensor unit.NOTE:GTo install, reverse the removal procedure.GAfterreplacement, performself-diagnosisforSRS. RefertoSRS Operation Check, TROUBLE DIAGNOSES Supple-mental Restraint System (SRS), RS-34.CAUTION:Airbagdiagnosissensorunitmustalwaysbeinstalledwithforward mark pointing towards the front of the vehiclefor proper operation. Also check air bag diagnosis sensorunit for cracks, deformities and rust before installation andreplace as required.ARS226Crash zone sensor1.Disconnect driver and passenger air bag module connectors.2.Remove front grille. Refer to BT section.3.Disconnect crash zone sensor connector.4.UsingtheTAMPERRESISTANT TORX(SizeT50), removespecial bolts. The crash zone sensor can then be removed.NOTE:GTo install, reverse removal procedure.GAfter replacement, perform Self-diagnosis for SRS. RefertoSRSOperationCheck, TROUBLEDIAGNOSESSupplemental Restraint System (SRS), RS-34.SUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-14Driver Air Bag Module and Spiral CableARS178ARS227REMOVALCAUTION:GBeforeservicingSRS, turntheignitionswitchOFF, dis-connect both battery cables and wait at least 3 minutes.GAlways work from the side of an air bag module.1.Remove lower lid from steering wheel, and disconnect driverair bag module connector.ARS2282.Removesidelids. UsingtheTAMPERRESISTANTTORX(Size T50), remove left and right special bolts. Driver air bagmodule can then be removed.ARS179CAUTION:GAlways place air bag module with pad side facing upward.GDo not attempt to disassemble air bag module.GThe special bolts are coated with bonding agent. Do notuse old bolts after removal; replace with new coated bolts.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-15SBF814EGDonotdroporimpactairbagmodule. Ifanyportionisdeformed or cracked, replace the module.GDo not expose the air bag module to temperatures exceed-ing 90C (194F).GDo not allow oil, grease or water to come in contact withthe air bag module.SST480C3.Set steering wheel in the neutral position.4.Disconnect horn connector and remove steering wheel nut.5.Using steering wheel puller, remove steering wheel. Be care-ful not to over-tighten puller bolt on steering wheel.CAUTION:Do not tap or bump the steering wheel.6.Remove steering column covers.7.Disconnect spiral cable from air bag harness.ARS1808.Remove the four spiral cable retaining screws. The spiral cablecan then be removed.CAUTION:GDo not attempt to disassemble spiral cable.GDo not apply lubricant to the spiral cable.ARS152INSTALLATION1.Set the front wheels in the straight-ahead position.2.Align the turn signal cancel tab with the notch of the combina-tion switch as shown.SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Driver Air Bag Module and Spiral Cable(Contd)RS-16ARS2483.Rotate the spiral cable fully clockwise until tight.4.Rotatethespiral cablecounterclockwiseasspecifiedbelowand align white pin with arrow on housing.Specified turns for spiral cable:Applied modelSpecified turns from neutral positionWith power steeringApprox. 2.5Without power steeringApprox. 4GWhenspiral cableiscentered, whitepinisalignedwitharrow on housing and yellow wheel shows in window.CAUTION:Thespiral cablemaysnapduringsteeringoperationif thespiral cableisinstalledimproperly. Also, withthesteeringlinkage disconnected, the spiral cable may snap by turning thesteering wheel beyond the specified number of turns. Alwaysperform SRS Self-diagnosis after installing the air bag module.5.Connect spiralcable to air bag harness and tighten screws.Install steering column covers.SBF818E6.Install steering wheel, setting spiral cable pin guide, and pullspiral cable connectors through.7.Connect horn connector and engage spiral cable with pawls insteering wheel.8.Tighten steering wheel nut.: 29 - 39 Nm (3.0 - 4.0 kg-m, 22 - 29 ft-lb)ARS2289.Positiondriverairbagmoduleandtightenwithnewspecialbolts.10. Connect driver air bag module connector.11. Install all lids.12. Connect both battery cables.13. Conduct Self-diagnosis to ensure entire SRS operates prop-erly (Use CONSULT or warning lamp check.). Turn the steer-ing wheel fully to the right and left to check that the spiral cableis set in the neutral position.14. If AIR BAG warning lamp blinks (in User mode), it shows thespiral cable may be snapped due to its improper position. Per-form Self-diagnosis again. (Use CONSULT or AIR BAG warn-ing lamp check.) If a malfunction is detected, replace the spi-ral cable with a new one.NOTE:GAfter replacement, perform Self-diagnosis for SRS. RefertoSRSOperationCheck, TROUBLEDIAGNOSESSupplemental Restraint System (SRS), RS-34.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)Driver Air Bag Module and Spiral Cable(Contd)RS-17ARS241Passenger Air Bag ModuleREMOVALCAUTION:GBeforeservicingSRS, turntheignitionswitchOFF, dis-connectbothbatterycablesandwaitforatleast3min-utes.GAlways work from the side of an air bag module.1.Open glove box assembly.2.Openlidof instrument panel lower passenger side, insideglove box.3.Remove passenger air bag module connector clip from lid.4.Disconnect passenger air bag module connector.5.Removegloveboxandinstrument panel lower passengerside. Refer to BT section (INSTRUMENT PANEL).ARS2426.UsingTAMPERRESISTANT TORX(SizeT50), removethetwo special bolts.7.Remove four mounting nuts.8.Remove passenger air bag module by releasing the clips fromthe top of the instrument panel.GAir bag module is heavy and should be supported usingboth hands during removal.CAUTION:GAlways place air bag module with pad side facing upward.GDo not attempt to disassemble air bag module.GThe special bolts are coated with a bonding agent. Do notuse old bolts after removal; replace with new coated bolts.GDonotinsertanyforeignobjects(screwdriver,etc.)intoair bag module connector.SBF814EGDonotdroporimpactairbagmodule. Ifanyportionisdeformed or cracked, replace the module.GDo not expose the air bag module to temperatures exceed-ing 90C (194F).GDo not allow oil, grease or water to come in contact withthe air bag module.SUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-18ARS242INSTALLATION1. Install passenger air bag module in instrument panel.a) Insert front edgeof passengerairbagmodulefirst toeaseinstallation.G Ensure harness is not caught between passenger air bag mod-ule and support bracket.b) Install four mounting nuts.c) Install two newspecial bolts usingTAMPERRESISTANTTORX (Size T50).2. Install instrument panel lower passenger side and glove box.ARS2413. Connect passenger air bag module connector.4. Attach passenger air bag module connector clip to lid.5. Close lid and glove box.6. Conduct Self-diagnosis to ensure SRS operates properly (UseCONSULT or warning lamp check.).NOTE:G After replacement, perform Self-diagnosis for SRS. RefertoSRSOperationCheck, TROUBLEDIAGNOSESSupplemental Restraint System (SRS), RS-34.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)Passenger Air Bag Module (Contd)RS-19ARS246Passenger Air Bag Deactivation SwitchREMOVALGBeforeservicingSRS, turntheignitionswitchOFF, dis-connectbothbatterycablesandwaitforatleast3min-utes.1.Detachinstrument staycover lower center frominstrumentpanel. Refer to BT section (INSTRUMENT PANEL).2.Disconnect passenger air bagdeactivationswitchharnessconnector and cigarette lighter harness connector.3.Remove instrument stay cover lower center.4.Remove two screws and remove passenger air bag deactiva-tion switch.INSTALLATIONCAUTION:Passenger air bagdeactivationswitchiskeyedfor properinstallation. Improperpositioningoftheswitchwill resultindamage to the switch.NOTE:GBesurethat passengerairbagdeactivationswitchandlock cylinder are in the same position as during removalfor proper engagement.GTo install, reverse removal procedure.GAfter replacement, perform Self-diagnosis for SRS. RefertoSRSOperationCheck, TROUBLEDIAGNOSESSupplemental Restraint System (SRS), RS-34.ARS247Passenger Air Bag Deactivation Switch LockCylinderREMOVALGBeforeservicingSRS, turntheignitionswitchOFF, dis-connectbothbatterycablesandwaitforatleast3min-utes.1.Detachinstrument staycover lower center frominstrumentpanel. Refer to BT section (INSTRUMENT PANEL).2.Disconnect passenger air bagdeactivationswitchharnessconnector and cigarette lighter harness connector.3.Remove instrument stay cover lower center.4.Remove four screws and housing from instrument stay coverlower center.5.Remove clip from bottom of housing.6.Remove passenger air bag deactivation switch lock cylinderfrom front of housing.INSTALLATIONNOTE:GBesurethat passengerairbagdeactivationswitchandlock cylinder are in the same position as during removalfor proper engagement.GTo install, reverse removal procedure.GAfter replacement, perform Self-diagnosis for SRS. RefertoSRSOperationCheck, TROUBLEDIAGNOSESSupplemental Restraint System (SRS), RS-34.SUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-20ARS245Passenger Air Bag Deactivation SwitchIndicatorREMOVALG BeforeservicingSRS, turntheignitionswitchOFF, dis-connectbothbatterycablesandwaitforatleast3min-utes.1. Removemeter cover. Refer toBTsection(INSTRUMENTPANEL).2. Release passenger air bag deactivation switch indicator tabsfrom back side of meter cover.3. Remove passenger air bag deactivation switch indicator fromfront side of meter cover.INSTALLATIONNOTE:G To install, reverse removal procedure.G After replacement, perform Self-diagnosis for SRS. Referto Passenger Air Bag Deactivation Switch IndicatorOperationCheck, TROUBLEDIAGNOSESSupple-mental Restraint System (SRS), RS-33.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-21Disposal of Air Bag ModuleGBefore disposing of air bag module, or vehicles equipped with such a system, deploy the system. If sucha system has already been deployed due to an accident, dispose of as indicated in DISPOSING OF AIRBAG MODULE (RS-25).GWhen deploying the air bag module, always use the Special Service Tool; Deployment tool KV99106400(Kent-Moore No. J38381).GWhen deploying the air bag module, stand at least 5 m (16 ft) away from the deployment component.GWhen deploying air bag module, a fairly loud noise is made, followed by smoke being released. The smokeis not poisonous, however, be careful not to inhale smoke since it irritates the throat and can cause chok-ing.GAlways activate one air bag module at a time.GDue to heat, leave air bag module unattended for more than 30 minutes after deployment.GBe sure to wear gloves when handling a deployed air bag module.GNever apply water to a deployed air bag module.GWash your hands clean after finishing work.GPlace the vehicle outdoors with an open space of at least 6 m (20 ft) on all sides when deploying air bagmodule while mounted in vehicle.GUse a voltmeter to make sure the vehicle battery is fully charged.GDo not dispose of the air bag module un-deployed.SRS019CHECKING DEPLOYMENT TOOLConnecting to batteryGPlace vehicle outdoors with at least 6 m (20 ft) of open spaceon all sides.GUseavoltmeter tomakesurethevehiclebattery is fullycharged.CAUTION:The battery must show voltage of 9.6V or more.Removethebatteryfromthevehicleandplaceit ondrywoodblocks approximately 5 m (16 ft) away from the vehicle.GWait 3 minutes after the vehicle battery is disconnected beforeproceeding.GConnect red clip of deployment tool to battery positive termi-nal and black clip to negative terminal.CAUTION:Makesurethepolarityiscorrect.Therightsidelampinthetool, markedDEPLOYMENTTOOLPOWER, shouldglowwith a green light. If the right side lamp glows red, reverse theconnections to the battery.SUPPLEMENTAL RESTRAINT SYSTEM (SRS)RS-22SBF266HDeployment tool checkPress the deployment tool switch to the ON position. The left sidelampinthetool, markedAIRBAGCONNECTORVOLTAGEshould illuminate. If it does not illuminate, replace the tool.Air bag deployment tool lamp illumination chart(Battery connected)Switch operationLeft side lamp, green*AIR BAG CONNECTORVOLTAGERight side lamp, green*DEPLOYMENT TOOLPOWEROFFOFFONONONON*: If thislampglowsred, thetool isconnectedtothebatteryincorrectly.Reverse the connections and make sure the lamp glows green.ARS185DEPLOYMENT PROCEDURES FOR AIR BAG MODULE(OUTSIDE OF VEHICLE)Unless the vehicle is being scrapped, deploying the air bag in thevehicleis not recommended. This may causedamagetothevehicle interior.Anchor air bag module bracket [KV99105300 (J41246)] in a visesecured to a firm foundation during deployment.ARS186Deployment of driver air bag module (outside ofvehicle)1.Using wire, firmly secure driver air bag module to air bag mod-ule bracket [SST: KV99105300 (J41246)] at two places.CAUTION:Use wire of at least 1 mm (0.04 in) diameter.2.Firmly secure air bag module bracket [SST: KV99105300(J41246)] with driver air bag module attached, in a vise.ARS1873.Connect deployment tool [SST: KV99106400 (J38381)] todriver air bag module connector.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)Disposal of Air Bag Module (Contd)RS-23ARS1884.Connect red clip of deployment tool to battery positive termi-nal and black clip to negative terminal.5.The lamp on the right side of the tool, marked DEPLOYMENTTOOL POWER , should glow green, not red.6.Press the button on the deployment tool. The left side lamp onthetool, markedAIRBAGCONNECTORVOLTAGE, willilluminate and the air bag module will deploy.CAUTION:When deploying the air bag module, stand at least 5 m(16 ft) away from the air bag module.ARS233Deployment of passenger air bag module (outside ofvehicle)1.Make an 8.5 mm (0.335 in) diameter hole in air bag modulebracket [SST: KV99105300 (J41246)] at the position shown infigure at left.ARS2342.Firmly secure air bag module bracket [SST: KV99105300(J41246)] in a vise.3.Match the two holes in air bag module bracket (held in vise)and passenger air bag module and fix them with two bolts [M8x 25 - 30 mm (0.98 - 1.18 in)].CAUTION:If a gap exists between passenger air bag module and air bagmodulebracket, useapieceofwoodinsertedinthegaptostabilize the air bag module.ARS2354.Connect deployment tool adapter [SST: KV991065S0 (J38381-30)] to deployment tool [SST: KV99106400 (J38381)] connec-tor and air bag module connector.ARS2365.Connect red clip of deployment tool to battery positive termi-nal and black clip to negative terminal.6.The lamp on the right side of the tool, marked DEPLOYMENTTOOL POWER , should glow green, not red.7.Press the button on the deployment tool. The left side lamp onthe tool, marked AIR BAG CONNECTOR VOLTAGE, will illu-minate and the air bag module will deploy.CAUTION:When deploying the air bag module, stand at least 5 m(16 ft) away from the air bag module.SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Disposal of Air Bag Module (Contd)RS-24ARS227ARS036DEPLOYMENT OF AIR BAG MODULE WHILE MOUNTEDIN VEHICLEWhendisposingof vehicles, deployair bagmodulewhileit ismounted in vehicle.CAUTION:When deploying air bag module, ensure vehicle is empty.1.Turn ignition switch OFF, disconnect both battery cables andwait at least 3 minutes.2.Disconnect air bag module connector.3.Connect deployment tool [SST:KV99106400(J38381)] con-nector to air bag module.For passenger air bag module, use adapter [SST:KV991065S0(J38381-30)] to attach module to deployment tool connector.4.Connect red clip of deployment tool to battery positive termi-nal and black clip to negative terminal.5.The lamp on the right side of the tool, marked DEPLOYMENTTOOL POWER , should glow green, not red.6.Press the button on the deployment tool. The left side lamp onthetool, markedAIRBAGCONNECTORVOLTAGE, willilluminate. Then the air bag module will deploy.ARS012DISPOSING OF AIR BAG MODULEDeployed air bag module is very hot. Before disposing of air bagmodule, wait at least 30 minutes. Seal them in a plastic bag beforedisposal.CAUTION:GNever apply water to a deployed air bag module.GBe sure to wear gloves when handling a deployed air bagmodule.GNo poisonous gas is produced upon air bag moduledeployment. However, be careful not to inhale gas since itirritates throat and can cause choking.GDo not attempt to disassemble air bag module.GAir bag module cannot be reused.GWash your hands clean after finishing work.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXSUPPLEMENTAL RESTRAINT SYSTEM (SRS)Disposal of Air Bag Module (Contd)RS-25Trouble Diagnosis IntroductionCAUTION:GDo not use electrical test equipment on any circuit related to the SRS unless instructed to in thisServiceManual. SRSwiringharnessesarecoveredwithyellowinsulationeitherjustbeforetheharness connectors or on the complete harness, for easy identification.GDonot attempt torepair, spliceormodifytheSRSwiringharness. If theharnessisdamaged,replace it with a new one.GKeep ground portion clean.DIAGNOSIS FUNCTIONThe SRS Self-diagnosis results can be read by using the AIR BAG warning lamp and/or CONSULT. Thereading of these results is accomplished using one of two modes User mode and Diagnosis mode.The User mode is exclusively prepared for the customer (driver). This mode warns the driver of a systemmalfunction through the operation of the AIR BAG warning lamp.The Diagnosis mode allows the technician to locate and inspect the malfunctioning part.The mode applications for the AIR BAG warning lamp and CONSULT are as follows:User modeDiagnosis modeDisplay typeAIR BAG warning lampXXON-OFF operationCONSULTXMonitoringDIAGNOSIS MODE FOR CONSULTGSELF-DIAG [CURRENT]A current Self-diagnosis result (also indicated by the number of warning lamp flashes in the Diagnosismode) is displayed on the CONSULT screen in real time. This refers to a malfunctioning part requiringrepairs.GSELF-DIAG [PAST]Diagnosis results previously stored in the memory are displayed on the CONSULT screen. The storedresults are not cleared until memory erasing is executed.GTROUBLE DIAG RECORDWith TROUBLE DIAG RECORD, diagnosis results previously erased by a reset operation can be dis-played on the CONSULT screen.ARS313GECU DISCRIMINATED NO.The air bag diagnosis sensor unit for each vehicle modelisassignedwithitsown, individual classificationnumber. Thisnumber will be displayed on the CONSULT screen, as shownat left. When replacing the air bag diagnosis sensor unit, refertothepart number for thecompatibility. After installation,replacement with a correct unit can be checked by confirmingthis classification number on the CONSULT screen.For NISSAN model D22 with crash zone sensor, the air bagdiagnosissensorunitclassificationnumberassignedis49.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-26HOW TO CHANGE SELF DIAGNOSIS MODEWith CONSULTFrom User mode to Diagnosis modeTouch AIRBAG on the SELECT SYSTEM screen. User mode automatically changes to Diagnosis mode.ARS198From Diagnosis mode to User modeTouch BACK key of CONSULT until SELECT SYSTEM appears, Diagnosis mode automatically changesto User mode.ARS199SBF921EWithout CONSULTFrom User mode to Diagnosis modeDiagnosis modecanbeactivatedonly whenamalfunctionisdetected, by pressing the door switch LH at least 5 times within 7seconds after turning the ignition switch ON. SRS willnot enterDiagnosis mode if no malfunction is detected.From Diagnosis mode to User modeG To return to User mode while a malfunction is being detected, turn ignition switch OFF, then back ON andpress the door switch LH at least 5 times within 7 seconds.G After a malfunction is repaired, turn ignition switch OFF for at least 1 second, then back ON. Diagnosismode returns to User mode.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnosis Introduction (Contd)RS-27HOW TO ERASE SELF DIAGNOSIS RESULTSWith CONSULTSELF-DIAG [CURRENT]A current Self-diagnosis result is displayed on the CONSULT screen in realtime. After the malfunction isrepaired completely, no malfunction is detected on SELF-DIAG [CURRENT].ARS300SELF-DIAG [PAST]ReturntotheSELF-DIAG[CURRENT] CONSULTscreenbypushing BACK key of CONSULT and select SELF-DIAG [CUR-RENT] in SELECT DIAG MODE. Touch ERASE in SELF-DIAG[CURRENT] mode.NOTE:If the memory of the malfunction in SELF-DIAG [PAST] is not erased, the User mode shows the sys-tem malfunction by the operation of the warning lamp even if the malfunction is repaired completely.TROUBLE DIAG RECORDThe memory of TROUBLE DIAG RECORD cannot be erased.Without CONSULTAfter a malfunction is repaired, turn ignition switch OFF for at least 1 second, then back ON. Diagnosis modereturns to User mode. At that time, the self-diagnosis result is cleared.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnosis Introduction (Contd)RS-28How to Perform Trouble Diagnoses for Quickand Accurate RepairA good understanding of the malfunction conditions can make troubleshooting faster and more accurate.In general, each customer feels differently about a malfunction. It is important to fully understand the symp-toms or conditions of a customer complaint.INFORMATION FROM CUSTOMERWHAT............ Vehicle modelWHEN........... Date, FrequenciesWHERE......... Road conditionsHOW .............. Operating conditions, SymptomsPRELIMINARY CHECKCheck that the following parts are in good order.G Battery [Refer to EL section (BATTERY).]G Fuse [Refer to EL section (Fuse, POWER SUPPLY ROUTING).]G System component-to-harness connectionsWORK FLOWACTION ITEM REFERENCE ITEMCheck inListen to customer complaints and requests.Perform preliminary check.Preliminary check (see above).Check for any service bulletins.Perform passenger air bag deactivation switch indicator operationcheck.Passenger Air Bag DeactivationSwitch Indicator Operation Check,RS-33.Perform self-diagnosis using AIR BAG warning lamp. User modeSRS Operation Check, RS-34.Inspect malfunctioning part. Diagnosis modePerform self-diagnosis using CONSULT.ORPerform self-diagnosis using AIR BAG warning lamp.G DIAGNOSTIC PROCEDURE 2:Using CONSULT, RS-35G DIAGNOSTIC PROCEDURE 6:Using AIR BAG warning lamp,RS-44.Repair/ReplaceNGFinal check Diagnosis mode and User modeOKG DIAGNOSTIC PROCEDURE 3:Using CONSULT, RS-39.G DIAGNOSTIC PROCEDURE 7:Using AIR BAG warning lamp,RS-46.Check outGIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-29SchematicARS308TROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-30Wiring Diagram SRSARS360GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-31ARS362TROUBLE DIAGNOSES Supplemental Restraint System (SRS)Wiring Diagram SRS (Contd)RS-32ARS240Passenger Air Bag Deactivation SwitchIndicator Operation CheckCheck the passenger air bag deactivationswitch indicator operation after turning theignition switch ON as shown below.G Does the indicator operation correspondto ON/OFF operation of passenger airbag deactivation switch?NoYesPassenger air bag deacti-vation switch indicatoroperation is OK. ConductSRS Operation Check.Refer to RS-34.Perform self-diagnosis using AIR BAGwarning lamp in User mode. Refer toSRS Operation Check, RS-34.NOTE:The passenger air bag deactivationswitch indicator can only be self-diag-nosed when a malfunction occurs andindicator illumination does not corre-spond to switch position.G Is SRS operation OK?OKNGPerform self-diagnosisusing CONSULT or AIRBAG warning lamp inDiagnosis mode. Refer toRS-35 or RS-44 respec-tively.If the indicator stays lit withthe passenger air bagdeactivation switch ON,leave switch in ON positionduring diagnosis. If theindicator does not light withswitch OFF, leave switch inOFF position during diag-nosis.Replace the passenger air bag deactiva-tion switch including the key cylinder. Con-duct Passenger Air Bag DeactivationSwitch Indicator Operation Check as afinal check.Passenger air bagdeactivation switchpositionPassenger air bagdeactivation switchindicatorONTurns off within7 secondsOFF Stays litGIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-33SRS073SRS Operation CheckDIAGNOSTIC PROCEDURE 1Checking SRS operation by using AIR BAG warning lamp User mode1. After turning ignition switch from OFF to ON, AIR BAG warn-ing lamp operates.2. CompareAIRBAG warninglampoperationtothechartbelow.AIR BAG warning lamp operation User mode SRS condition Reference itemMRS095ANo malfunction isdetected.No further action is neces-sary.MRS096AThe system is malfunction-ing and needs to berepaired as indicated.Go to DIAGNOSTIC PRO-CEDURE 2, or 6, RS-35 or44.MRS097AAir bag is deployed. Go to COLLISIONDIAGNOSIS, RS-51.Air bag fuse for air bagdiagnosis sensor unit orcircuit is malfunctioningand needs to be repaired.Go to DIAGNOSTIC PRO-CEDURE 9, RS-48.MRS098AOne of the following hasoccured and needs to berepaired.GMeter fuse is blown.GAIR BAG warninglamp circuit is shortedor open.GAir bag diagnosis sen-sor unit is malfunction-ing.Go to DIAGNOSTIC PRO-CEDURE 10, RS-49.NOTE:If AIRBAG warning lamp operates differently fromtheoperationsshownabove, refertoAIRBAGwarninglampoperation Diagnosis mode , DIAGNOSTIC PROCEDURE 6,step 4, RS-44. Then repair as necessary.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-34ARS230Trouble Diagnoses with CONSULTDIAGNOSTIC PROCEDURE 2InspectingSRSmalfunctioningpartsbyusingCONSULTDiagnosis mode1. Turn ignition switch OFF.2. Connect CONSULT to Data link connector.SRS0463. Turn ignition switch ON.4. Touch START.SRS0745. Touch AIRBAG.SRS0476. Touch SELF-DIAG [CURRENT].ARS2937. Self-diagnosis result is displayed on SELF-DIAG[CUR-RENT].GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-35ARS290GIf no malfunction is detected on SELF-DIAG [CURRENT]but malfunctionisindicatedbytheAIRBAGwarninglampinUsermode, gotoDIAGNOSTICPROCEDURE4,RS-40 for diagnosing the following cases:G Self-diagnosisresult (previouslystoredinthememory)might not have been erased after repair.G The SRS system is malfunctioning intermittently.8. Touch PRINT.9. ComparediagnosticcodestotheCONSULTDIAGNOSTICCODE CHART, RS-37.10. TouchBACK keyof CONSULTuntil SELECTSYSTEMappears in order to return to User mode from Diagnosis mode,then turn off CONSULT.11. Turn ignition switch OFF, then disconnect CONSULT and bothbattery cables.12. Repair the system as outlined by the Repair order in CON-SULT DIAGNOSTICCODECHART that correspondstotheself-diagnosis result. For replacement procedure of componentparts, refer to RS-14.13. After repairing the system, connect battery cables and go toDIAGNOSTIC PROCEDURE 3, RS-39 for final checking.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses with CONSULT (Contd)RS-36CONSULT DIAGNOSTIC CODE CHART (SELF-DIAG [CURRENT])Self-diagnosis result Explanation/Possible causesRepair order*Recheck SRS using CONSULTat each replacementNO SELF DIAGNOSTICFAILURE INDICATEDWhen malfunction is indi-cated by the AIR BAGwarning lamp in Usermode.GSelf-diagnosisresult SELF-DIAG[PAST] (previouslystored in thememory) might nothave been erasedafter repair.GIntermittent mal-function has beendetected in thepast.GGo to DIAGNOSTIC PROCEDURE 4,RS-40.GNo malfunction is detected. GGo to DIAGNOSTIC PROCEDURE 3,RS-39.AIRBAG MODULE[OPEN]GAir bag module circuit is open (including thespiral cable).1. Visually check wiring harness connections.2. Replace air bag harness if it has visibledamage.3. Replace spiral cable.4. Replace air bag module.(Before disposing of it, it must bedeployed.)5. Replace air bag diagnosis sensor unit.6. Replace air bag harness.AIRBAG MODULE[VB-SHORT]GAir bag module circuit is shorted to some powersupply circuit (including the spiral cable).AIRBAG MODULE[GND-SHORT]GAir bag module circuit is shorted to ground(including the spiral cable).AIRBAG MODULE[SHORT]GAir bag module circuits are shorted to eachother.ASSIST A/B MODULE[VB-SHORT]GPassenger air bag module circuit is shorted tosome power supply circuit.1. Visually check wiring harness connection.2. Replace air bag harness if it has visibledamage.3. Replace passenger air bag module.(Before disposing of it, it must bedeployed.)4. Replace air bag diagnosis sensor unit.5. Replace air bag harness.ASSIST A/B MODULE[OPEN]GPassenger air bag module circuit is open.ASSIST A/B MODULE[GND-SHORT]GPassenger air bag module circuit is shorted toground.ASSIST A/B MODULE[SHORT]GPassenger air bag module circuits are shortedto each other.CRASH ZONE SEN-CTR[OPEN/UPR-VB-SHORT]GCrash zone sensor circuit is open, orGCrash zone sensor circuit is shorted to somepower supply circuit.1. Visually check wiring harness connections.2. Replace air bag harness if it has visibledamage.3. Replace crash zone sensor.4. Replace air bag diagnosis sensor unit.5. Replace air bag harness for crash zonesensor.CRASH ZONE SEN-CTR[SHORT/UPR-GND-SHORT]GBoth crash zone sensor circuits are shorted, orGCrash zone sensor circuit is shorted to ground.CONTROL UNIT GLow battery voltage (Less than 9V). GGo to DIAGNOSTIC PROCEDURE 3(RS-39) after charging battery.GAir bag diagnosis sensor unit is malfunctioning. 1. Visually check wiring harness connections.2. Replaceair bagharnessif it hasvisibledamage.3. Replace air bag diagnosis sensor unit.4. Replace air bag harness.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses with CONSULT (Contd)RS-37Self-diagnosis result Explanation/Possible causesRepair order*Recheck SRS using CONSULTat each replacementCode B4orPASS A/B DEACT SWGActivate terminal is open. 1. Visually check wiring harness connections.2. Replace air bag harness if it has visibledamage.3. Replace passenger air bag deactivationswitch. (The key cylinder of passenger airbag deactivation switch does not have tobe replaced.)4. Replace air bag diagnosis sensor unit.5. Replace air bag harness.GActivate terminal is shorted to ground.GDeactivate terminal is open.GDeactivate terminal is shorted to ground.GActivate terminal and deactivate terminal areshorted to each other.Code B5orPASS A/B DEACT SWINDICATORGPassenger air bag deactivation switch indicatorcircuit is open.1. Visually check wiring harness connections.2. Replace air bag harness if it has visibledamage.3. Replace passenger air bag deactivationswitch indicator.4. Replace air bag diagnosis sensor unit.5. Replace air bag harness.GPassenger air bag deactivation switch indicatorcircuit is shorted to some power supply circuit.GPassenger air bag deactivation switch indicatorcircuit is shorted to ground.INDEFINITE FAILURES[AIR BAGS]GPassenger air bag deactivation switch status isnot identified.1. Visually check wiring harness connections.2. Replace air bag harness if it has visibledamage.3. Replace passenger air bag deactivationswitch.4. Replace air bag diagnosis sensor unit.5. Replace air bag harness.*Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is eliminated using theAIR BAG warning lamp (in User mode) or CONSULT each time repair is finished. If malfunction is still observed, proceed to thenext step. When malfunction is eliminated, further repair work is not required.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses with CONSULT (Contd)RS-38ARS230DIAGNOSTIC PROCEDURE 3Final checking after repairing SRS by using CONSULT Diag-nosis mode1. Check that both battery cables are connected.2. Connect CONSULT to Data link connector.3. Turn ignition switch from OFF to ON.SRS0464. Touch START.SRS0745. Touch AIRBAG.SRS0476. Touch SELF-DIAG [CURRENT].ARS2907. If nomalfunctionisdetectedonSELF-DIAG[CURRENT],repair of SRS is completed.G If any malfunction was detected on SELF-DIAG [CURRENT],the malfunctioning part is not repaired completely or anothermalfunctioning part is detected. Go to DIAGNOSTIC PROCE-DURE 2, RS-35 and repair malfunctioning part completely.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses with CONSULT (Contd)RS-39ARS3008. Touch ERASE.NOTE:TouchERASEtoclearthememoryofthemalfunction(SELF-DIAG [PAST]).If thememoryof themalfunctioninSELF-DIAG[PAST]isnoterased, theUser modeshowsthesystemmalfunctionbytheoperation of the warning lamp even if the malfunction is repairedcompletely.SRS0509. TouchBACKkeyof CONSULT toSELECT DIAGMODEscreen.Touch SELF-DIAG [PAST].ARS29610. Check that no malfunction is detected on SELF-DIAG[PAST].11. TouchBACK keyof CONSULTuntil SELECTSYSTEMappears in order to return to User mode from Diagnosis mode,turn off CONSULT, then disconnect CONSULT.12. Turn ignition switch OFF.13. Go to SRS Operation Check, RS-34 to check SRS opera-tionby using AIR BAG warning lamp with User mode.DIAGNOSTIC PROCEDURE 4 (Continued fromDIAGNOSTIC PROCEDURE 2)Inspecting SRS malfunctioning recordIs it the first time for maintenance ofSRS?YesNoSelf-diagnosis resultSELF-DIAG [PAST] (pre-viously stored in thememory) might not havebeen erased after repair.Go to DIAGNOSTIC PRO-CEDURE 3, step 8 (seeabove).Go to DIAGNOSTIC PROCEDURE 5,RS-41.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses with CONSULT (Contd)RS-40ARS230DIAGNOSTIC PROCEDURE 5InspectingSRSintermittentmalfunctionbyusingCONSULT Diagnosis mode1. Turn ignition switch OFF.2. Connect CONSULT to Data link connector.SRS0463. Turn ignition switch ON.4. Touch START.SRS0745. Touch AIRBAG.SRS0506. Touch SELF-DIAG [PAST].ARS2957. If self-diagnosis result is displayed on SELF-DIAG [PAST], goto step 10.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses with CONSULT (Contd)RS-41ARS296If no malfunction is detected on SELF-DIAG[PAST], touchBACK and go back to SELECT DIAG MODE.SRS0558. Touch TROUBLE DIAG RECORD.NOTE:WithTROUBLEDIAGRECORD, self-diagnosisresultspreviously erased by a reset operation can be displayed.ARS2979. Self-diagnosis result is displayed on TROUBLE DIAGRECORD.10. Touch PRINT.11. Compareself-diagnosisresult totheINTERMITTENTMAL-FUNCTION DIAGNOSTIC CODE CHART, RS-43.12. TouchBACK keyof CONSULTuntil SELECTSYSTEMappears, then turn off CONSULT.13. Turn ignition switch OFF, then disconnect CONSULT and bothbattery cables.14. Repair the system as outlined by the Repair order that corre-sponds to the self-diagnosis result in INTERMITTENT MAL-FUNCTION DIAGNOSTIC CODE CHART, RS-43. For replace-ment procedure of component parts, refer to RS-14.15. Go to DIAGNOSTIC PROCEDURE 3, RS-39.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses with CONSULT (Contd)RS-42INTERMITTENT MALFUNCTION DIAGNOSTIC CODE CHART (SELF-DIAG [PAST] orTROUBLE DIAG RECORD)Self-diagnosis result Explanation Repair order*NO SELF DIAGNOSTICFAILURE INDICATED.GNo malfunction is detected. GGo to DIAGNOSTIC PROCEDURE 3, RS-39.AIRBAG MODULE[OPEN]GDriver air bag module circuit is open (includingthe spiral cable).1. Visually check wiring harness connections.2. Replace air bag harness if it has visible dam-age.3. If the harness visual check result is OK,replace driver air bag module (Before dispos-ing of it, it must be deployed.), air bag diag-nosis sensor unit and spiral cable.AIRBAG MODULE[VB-SHORT]GDriver air bag module circuit is shorted to somepower supply circuit (including the spiral cable).AIRBAG MODULE[GND-SHORT]GDriver air bag module circuit is shorted toground (including the spiral cable).AIRBAG MODULE[SHORT]GDriver air bag module circuits are shorted toeach other.ASSIST A/B MODULE[VB-SHORT]GPassenger air bag module circuit is shorted tosome power supply circuit.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible dam-age.3. If the harness visual check result is OK,replace air bag diagnosis sensor unit and airbag harness.ASSIST A/B MODULE[OPEN]GPassenger air bag module circuit is open. 1. Visually check wiring harness connections.2. Replace air bag harness if it has visible dam-age.3. If the harness visual check result is OK,replace passenger air bag module (Beforedisposing of it, it must be deployed.) and airbag diagnosis sensor unit.ASSIST A/B MODULE[GND-SHORT]GPassenger air bag module circuit is shorted toground.ASSIST A/B MODULE[SHORT]GPassenger air bag module circuits are shortedto each other.CRASH ZONE SEN-CTR[OPEN/UPR-VB-SHORT]GCrash zone sensor circuit is open, orGCrash zone sensor circuit is shorted to somepower supply circuit.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible dam-age.CRASH ZONE SEN-CTR[SHORT/UPR-GND-SHORT]GBoth crash zone sensor circuits are shorted, orGCrash zone sensor circuit is shorted to ground.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible dam-age.3. If the harness visual check result is OK,replace crash zone sensor.CONTROL UNIT GLow battery voltage (Less than 9V). GGo to DIAGNOSTIC PROCEDURE 3(RS-39) after charging battery.GAir bag diagnosis sensor unit is malfunctioning. GReplace air bag diagnosis sensor unit.Code B4orPASS A/B DEACT SWGActivate terminal is open. 1. Visually check wiring harness connections.2. Replace air bag harness if it has visible dam-age.3. If the harness visual check result is OK,replace passenger air bag deactivationswitch (The key cylinder of passenger airbag deactivation switch does not have to bereplaced.).GActivate terminal is shorted to ground.GDeactivate terminal is open.GDeactivate terminal is shorted to ground.GActivate terminal and deactivate terminal areshorted to each other.Code B5orPASS A/B DEACT SWINDICATORGPassenger air bag deactivation switch indicatorcircuit is open.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible dam-age.3. If the harness visual check result is OK,replace passenger air bag deactivationswitch indicator.GPassenger air bag deactivation switch indicatorcircuit is shorted to some power supply circuit.GPassenger air bag deactivation switch indicatorcircuit is shorted to ground.INDEFINITE FAILURES[AIR BAGS]GPassenger air bag deactivation switch status isnot identified.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible dam-age.3. If the harness visual check result is OK,replace passenger air bag deactivationswitch and air bag diagnosis sensor unit.*Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is eliminated using theAIR BAG warning lamp (in User mode) or CONSULT each time repair is finished. If malfunction is still observed, proceed to thenext step. When malfunction is eliminated, further repair work is not required.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses with CONSULT (Contd)RS-43SBF921ETrouble Diagnoses without CONSULTDIAGNOSTIC PROCEDURE 6InspectingSRSmalfunctioningpartsbyusingAIRBAGwarning lamp Diagnosis modeNOTE:SRS will not enter Diagnosis mode if no malfunction isdetected in User mode.1. Open drivers door.2. Turn ignition switch from OFF to ON.3. Press door switch LH at least 5 times within 7 seconds afterturning ignition switch ON.SRS is now in Diagnosis mode.4. AIR BAG warning lamp operates in Diagnosis mode as fol-lows:NOTE:If SRS does not enter Diagnosis mode even though malfunc-tionisdetectedinUsermode, gotoDIAGNOSTICPROCE-DURE 11, RS-50.No. AIR BAG warning lamp operation Diagnosis mode SRS condition1MRS100Aa throughb are repeated.GSelf-diagnosisresult (previ-ously stored inthe memory)might not havebeen erasedafter repair.GIntermittent mal-function hasbeen detectedin the past.Go to DIAGNOS-TIC PROCEDURE8, RS-48.2MRS099Aa throughd are repeated.NOTE:a Interval Ib Start signal (Start signalidentifies display modes)c Interval IId Indicates malfunctioningpart (0.5 sec. ON and0.5 sec. OFF is countedas one flash.)The system is mal-functioning andneeds to berepaired.5. Malfunctioning part is indicated by the number of flashes (partd ). Comparethenumber of flashestoWARNINGLAMPFLASH CODE CHART and locate malfunctioning part.6. Turn ignition switch OFF, and disconnect both battery cables.7. Repair the system as outlined by the Repair order in WARN-INGLAMPFLASHCODECHARTthat correspondstotheflashcode. Forreplacement procedureof component parts,refer to RS-14.8. After repairing the system, go to DIAGNOSTIC PROCEDURE7, RS-46.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-44WARNING LAMP FLASH CODE CHARTWarn-inglampFlash coded(# of flashes)ExplanationRepair order*Recheck SRS at each replacementAIRBAGwarninglamp0 GSelf-diagnosis result might not havebeen erased after repair.GIntermittent malfunction has beendetected in the past.GGo to DIAGNOSTIC PROCEDURE 8 (RS-48).2 GDriver air bag module circuit is mal-functioning.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible damage.3. Replace spiral cable.4. Replace driver air bag module.(Before disposing of it, it must be deployed.)5. Replace air bag diagnosis sensor unit.6. Replace air bag harness.6 GCrash zone sensor is malfunctioning. 1. Visually check wiring harness connections.2. Replace air bag harness if it has visible damage.3. Replace crash zone sensor.4. Replace air bag diagnosis sensor unit.5. Replace air bag harness for crash zone sensor.7 GAir bag diagnosis sensor unit is mal-functioning.1. Visually check wiring harness connections.2. Replace air bag diagnosis sensor unit.3. Replace air bag harness.8 GPassenger air bag module circuit ismalfunctioning.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible damage.3. Replace passenger air bag module.(Before disposing of it, it must be deployed.)4. Replace air bag diagnosis sensor unit.5. Replace air bag harness.9 GPassenger air bag deactivationswitch status is not identified.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible damage.3. Replace passenger air bag deactivation switch. (The keycylinder of passenger air bag deactivation switch doesnot have to be replaced.)4. Replace air bag diagnosis sensor unit.5. Replace air bag harness.10 GPassenger air bag deactivationswitch is malfunctioning.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible damage.3. Replace passenger air bag deactivation switch. (The keycylinder of passenger air bag deactivation switch doesnot have to be replaced.)4. Replace air bag diagnosis sensor unit.5. Replace air bag harness.11 GPassenger air bag deactivationswitch indicator is malfunctioning.1. Visually check wiring harness connections.2. Replace air bag harness if it has visible damage.3. Replace passenger air bag deactivation switch indicator.4. Replace air bag diagnosis sensor unit.5. Replace air bag harness.*Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is eliminated using theAIR BAG warning lamp (in User mode) or CONSULT each time repair is finished. If malfunction is still observed, proceed to thenext step. When malfunction is eliminated, further repair work is not required.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses without CONSULT(Contd)RS-45SBF921EDIAGNOSTIC PROCEDURE 7Final checking after repairing SRS by using AIR BAG warn-ing lamp Diagnosis mode and User mode1. After repairing SRS, connect both battery cables.2. Open drivers door.3. Turn ignition switch from OFF to ON.4. AIR BAG warning lamp operates in Diagnosis mode as fol-lows:No. AIR BAG warning lamp operation Diagnosis mode SRS condition1MRS100Aa throughb are repeated. No malfunc-tion isdetected orrepair is com-pleted.No furtheraction is nec-essary.2MRS099Aa throughd are repeated.NOTE:a Interval Ib Start signal (Start signalidentifies display modes.)c Interval IId Indicates malfunctioningpart (0.5 sec. ON and 0.5sec. OFF is counted asone flash.)The system ismalfunctioningand needs tobe repaired.NOTE:Whenairbagdiagnosissensorunit isreplacedwithanewone; the AIR BAG warning lamp will operate in User mode.Checking the AIR BAG warning lamp operation in Diagnosismode is not required. Go to step 6.5. If AIR BAG warning lamp operates as shown in No. 1 in thechart above, turn ignition switch OFF to reset from Diagnosismode to User mode and to erase the memory of the malfunc-tion.If AIR BAG warning lamp operates as in No. 2 in the chartabove, the malfunctioning part is not repaired completely, oranother malfunctioning part is detected. Go to DIAGNOSTICPROCEDURE 6, RS-44 and repair malfunctioning part com-pletely.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses without CONSULT(Contd)RS-466. Turn ignition switch ON. AIR BAG warning lamp operates inUser mode. Compare AIR BAG warning lamp operation tothe chart below.NOTE:IfswitchingDiagnosismodetoUsermodeisrequiredwhilemalfunction is being detected, turn ignition switch from OFFtoON. ThenpressdoorswitchLHatleast5timeswithin7seconds after turning ignition switch ON.SRS is now in User mode.AIR BAG warning lamp operation User mode SRS condition Reference itemMRS095ANo malfunction isdetected.No further action is neces-sary.MRS096AThe system is malfunction-ing and needs to berepaired as indicated.Go to DIAGNOSTIC PRO-CEDURE 2 or 6, RS-35 or44.MRS097AAir bag is deployed. Go to COLLISIONDIAGNOSIS, RS-51.Air bag fuse for air bagdiagnosis sensor unit orcircuit is malfunctioningand needs to be repaired.Go to DIAGNOSTIC PRO-CEDURE 9, RS-48.MRS098AOne of the following hasoccured and needs to berepaired.GMeter fuse is blown.GAIR BAG warninglamp circuit is shortedor open.GAir bag diagnosis sen-sor unit is malfunction-ing.Go to DIAGNOSTIC PRO-CEDURE 10, RS-49.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses without CONSULT(Contd)RS-47DIAGNOSTIC PROCEDURE 8 (Continued fromDIAGNOSTIC PROCEDURE 6)Inspection SRS malfunctioning recordIs it the first time for maintenance of SRS?YesNoSelf-diagnosis result (previ-ously stored in the memory)might not have been erasedafter repair.Go to DIAGNOSTIC PRO-CEDURE 7, step 5 (RS-46).Go to DIAGNOSTIC PROCEDURE 5,RS-41. Further inspection cannot be per-formed without CONSULT.ARS231Trouble Diagnoses: AIR BAG Warning LampDoes Not Turn OffDIAGNOSTIC PROCEDURE 9ARS037Is air bag module deployed?NoYesRefer to COLLISIONDIAGNOSIS, RS-51.Is Air bag fuse OK?YesNoReplace fuse and turn igni-tion switch ON. If Air bagfuse blows again, repairmain harness and/orreplace air bag harness.Connect CONSULT and touchSTART.G Is AIRBAG displayed onCONSULT?YesNoVisually check the wiringharness connection of airbag diagnosis sensor unit.If the harness connectioncheck is OK, replace airbag diagnosis sensor unit.Is harness connection between warninglamp and air bag diagnosis sensor unitOK?YesNoConnect warning lamp andair bag diagnosis sensorunit properly. If warninglamp still does not go off,replace harness.Replace air bag diagnosis sensor unit.TROUBLE DIAGNOSES Supplemental Restraint System (SRS)Trouble Diagnoses without CONSULT(Contd)RS-48ARS232Trouble Diagnoses: AIR BAG Warning LampDoes Not Turn OnDIAGNOSTIC PROCEDURE 10Is Meter fuse OK?YesNoReplace fuse and turn igni-tion switch ON. If Meterfuse blows again, repairmain harness.Is warning lamp LED OK?YesNoReplace warning lampLED.1. Disconnect air bag diagnosis sensorunit connector.2. Turn ignition switch ON.GDoes AIR BAG warning lamp turn on?YesNoCheck the ground circuit ofAIR BAG warning lamp.Replace air bag diagnosis sensor unit.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXTROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-49SRS058Trouble Diagnoses: SRS Does Not EnterDiagnosis Mode Using Door SwitchARS197SRS060DIAGNOSTIC PROCEDURE 11Disconnect both battery cables and checkbattery voltage using circuit tester.G Is battery voltage more than 9V?YesNoCharge battery.Remove door switch LH and check conti-nuity between door switch LH connectorterminals2 and3 under the followingconditions.OKNGReplace door switch LH.Check harness continuity between doorswitch LH harness connector terminal3and body ground.G Does continuity exist?YesNoReplace or repair harness.Replace air bag diagnosis sensor unit.Go to SRS Operation Check, RS-34.Condition ContinuityDoor switch is depressed(Door is closed).NODoor switch is released (Dooris open).YESTROUBLE DIAGNOSES Supplemental Restraint System (SRS)RS-50To repair the SRS, perform the following steps.When SRS is activated in a collision:1 Replace the air bag diagnosis sensor unit.2 Remove the air bag modules.3 Check the SRS components using the table shown on the next page.GReplace any SRS components showing visible signs of damage (dents, cracks and deformation).4 Install new air bag modules.5 Conduct Self-diagnosis. Refer to SRS Operation Check, RS-34. Ensure entire SRS operates properly.When SRS is not activated in a collision:1 Check the SRS components using the table shown on the next page.GReplace any SRS components showing visible signs of damage (dents, cracks and deformation).2 Conduct Self-diagnosis using CONSULT and AIR BAG warning lamp. Refer to SRS Operation Check,RS-34. Ensure entire SRS operates properly.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXCOLLISION DIAGNOSISRS-51SRS inspectionPart SRS is activated SRS is NOT activatedAir bag module(driver and passen-ger side)REPLACEInstall with newbolts.1. Remove air bag module. Check harness cover and connectors for damage, ter-minals for deformities, and harness for binding.2-1. Install driver air bag module into the steering wheel to check fit and alignmentwith the wheel.2-2. Install passenger air bag module into the instrument panel to check fit with theinstrument panel.3. No damage found, reinstall with new bolts.4. If damagedREPLACE. Air bag must be deployed before discarding.Crash zone sensor 1. Check body and sensor bracket for deformities and rust.2. Check sensor case for dents, cracks, scratches, deformities and rust.3. Check sensor harness, connector, and terminals for binding, damage, and deformities.4. If no damage is found, reinstall with new bolts.5. If damagedREPLACE.Instrument panel 1. When passenger air bag inflates, check the following points for bending, deformities and cracks:GOpening portion for passenger air bagGPassenger air bag module bracketsGThe portions securing the instrument panel2. If no damage is found, reinstall the instrument panel.3. If damagedREPLACE the instrument panel with new bolts.COLLISION DIAGNOSISRS-52PartSRS is activatedSRS is NOT activatedAir bag diagnosissensor unitREPLACEInstall with newbolts.1. Check case and bracket for dents, cracks or deformities.2. Check connectors for damage, and terminals for deformities.3. If no damage is found, reinstall with new bolts.4. If damagedREPLACE.Steering wheel1. Visually check steering wheel for deformities.2. Check harness (built into steering wheel) and connectors for damage, and terminals for deformities.3. Install air bag module to check fit or alignment with steering wheel.4. Check steering wheel for excessive free play.5. If no damage is found, reinstall the steering wheel.6. If damagedREPLACE.Spiral cable1. Visually check spiral cable and combination switch for damage.2. Check connectors, flat cable and protective tape for damage.3. Check steering wheel for noise, binding or heavy operation.4. If no damage is found, reinstall the spiral cable.5. If damagedREPLACE.Passenger air bagdeactivation switchand indicator1. Visually check passenger air bag deactivation switch and indicator for dents, cracks and deformities.2. Check the harness and connectors for damage, and terminals for deformities.3. If damagedREPLACE.WARNING:After SRS maintenance or repair, make sure the passenger air bag deactivation switch is in thesame position (ON or OFF) as when the vehicle arrived for service.Harness and Con-nectors1. Check connectors for poor connection, damage, and terminals for deformities.2. Check harness for binding, chafing, cuts and deformities.3. If no damage is found, reinstall.4. DamagedREPLACE damaged section of harness. Do not attempt to repair, splice or modify any SRSharness.GIMAEMLCECFECLMTATTFPDFARABRSTRSBTHAELIDXCOLLISION DIAGNOSISRS-53NOTESRS-54