47
MINERA ESCONDIDA LTDA. PROYECTO LIXIVIACIÓN DE SÚLFUROS MEMORIA DE CÁLCULO Nº 2325-0000-265-CS-0007 MALLAS DE PUESTA A TIERRA Preparado por: FLUOR CHILE S.A. APROBACIONES TÉCNICAS: Jefe de Disciplina Roberto Falck Gerente de Área Sergio Meza/John Bertoia/Mike Friese Gerente de Ingeniería Carlos Astorga Cliente Robert Jaedecke REVISIÓN POR EMISIÓN FECHA REVISADO POR APROBADO POR B J. Muñoz Emitido para Información del Cliente 02-Dic.-04 R. Falck C. Astorga 0 J. Muñoz Emitido para Construcción 04-Ene.-05 R. Falck C. Astorga COMENTARIOS DEL CLIENTE ®

2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Embed Size (px)

Citation preview

Page 1: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LTDA.

PROYECTO LIXIVIACIÓN DE SÚLFUROS

MEMORIA DE CÁLCULO Nº 2325-0000-265-CS-0007

MALLAS DE PUESTA A TIERRA

Preparado por:

FLUOR CHILE S.A.

APROBACIONES TÉCNICAS:

Jefe de Disciplina Roberto Falck Gerente de Área Sergio Meza/John Bertoia/Mike Friese Gerente de Ingeniería Carlos Astorga Cliente Robert Jaedecke

REVISIÓN POR EMISIÓN FECHA REVISADO POR

APROBADO POR

B J. Muñoz Emitido para Información del Cliente 02-Dic.-04 R. Falck C. Astorga 0 J. Muñoz Emitido para Construcción 04-Ene.-05 R. Falck C. Astorga

COMENTARIOS DEL CLIENTE

®

Page 2: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Página 1 de 5 PROYECTO N° 232500 Enero, 2005 REV. 0 FLUOR

TABLA DE CONTENIDOS

1.0 INTRODUCCIÓN............................................................................................................. 2

2.0 ALCANCE ......................................................................................................................... 2

3.0 DESCRIPCIÓN DE LAS INSTALACIONES................................................................ 2

4.0 ANTECEDENTES ............................................................................................................ 3

5.0 NORMAS ........................................................................................................................... 4

6.0 BASES DE CÁLCULO..................................................................................................... 4

7.0 METODOLOGÍA DE CÁLCULO .................................................................................. 4

8.0 RESULTADOS.................................................................................................................. 4

9.0 CONCLUSIONES ............................................................................................................. 5

10.0 RECOMENDACIONES ................................................................................................... 5

ANEXOS: ANEXO 1 RESUMEN DE RESULTADOS.

(1 HOJA) ANEXO 2 REPORTES DEL ETAP.

(33 HOJAS) ANEXO 3 RESUMEN MEDICIONES DE RESISTIVIDAD EN ESCONDIDA

(MARZO 2004- MAYO 2004). (1 HOJA)

ANEXO 4 RESULTADOS DEL ANALISIS DE LA INTERCONEXION DE MALLAS DE

PUESTA A TIERRA. (CORREO ELECTRONICO DE INGENDESA) (2 HOJAS)

Page 3: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Página 2 de 5 PROYECTO N° 232500 Enero, 2005 REV. 0 FLUOR

1.0 INTRODUCCIÓN

El Proyecto Lixiviación de Súlfuros, de Minera Escondida Ltda., considera la construcción de todas las instalaciones para las nuevas plantas de Electroobtención (EW) y de Extracción por Solventes (SX), en las actuales instalaciones de Minera Escondida Ltda., ubicadas en la segunda región, al norte de Chile, 180 [km] al sureste de la ciudad de Antofagasta, en el desierto de Atacama, a una altitud de 3200 [m.s.n.m.].

Además, considera instalaciones en el Puerto de Coloso, aproximadamente a 16 [km] al sur de Antofagasta, a una altitud de 10 [m.s.n.m.], y en las estaciones de bombeo de agua Nos. 2, 3 y 4, ubicadas a lo largo del nuevo acueducto entre Coloso y la planta, a una altitud de 710, 1460 y 2300 [m.s.n.m.] respectivamente.

2.0 ALCANCE

El objetivo de esta memoria de cálculo es dimensionar las mallas de puesta a tierra requeridas en las instalaciones del Proyecto.

Las mallas de puesta a tierra cumplirán con las exigencias indicadas en la Norma IEEE Std. 80, año 2000, en lo referente a voltajes de paso y de contacto.

Además, las mallas cumplirán con la restricción de alcanzar una resistencia de 25 [Ohm] máximos, establecidos en el documento No. 2325-0000-265-DC-0001, “Criterio de Diseño Eléctrico”.

Para las mallas de puesta a tierra de las bombas en las Estaciones de bombeo Nos. 2, 3 y 4, se consideró una extensión de la malla calculada por Ingendesa, para el patio de alta tensión y sala eléctrica, utilizando el mismo reticulado. La misma consideración se hizo para las instalaciones en Coloso, (Planta Desaladora y Estación de bombeo No. 1), con una extensión de la malla de puesta a tierra existente.

3.0 DESCRIPCIÓN DE LAS INSTALACIONES

Las instalaciones involucradas en esta memoria de cálculo son los siguientes:

• Salas eléctricas Nos. 608, 609, 610, 611, 612, 613, 614 y 615, en la Planta EW.

• Salas eléctricas Nos. 601, 602 y 606, en la Planta SX.

• Switch house y subestación móvil en la pila de lixiviación de la Planta SX (Típico).

• Sala eléctrica No. 627, Planta de Inoculación.

Page 4: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Página 3 de 5 PROYECTO N° 232500 Enero, 2005 REV. 0 FLUOR

4.0 ANTECEDENTES

Los antecedentes utilizados en esta memoria de cálculo son los siguientes:

• Mediciones de resistividad de terreno realizadas por Ingendesa. (Ver Anexo 3)

• Plano 2325-3100-265-DW-4301, Rev. 0 (Switch House - Típico)

• Plano 2325-3100-265-DW-4302, Rev. 0 (Subestación Móvil - Típico)

• Plano 2325-3100-265-DW-4303, Rev. 0 (Sala eléctrica # 627 – Planta Inoculación)

• Plano 2325-3300-265-DW-4302, Rev. 0 (Sala eléctrica # 601)

• Plano 2325-3300-265-DW-4303, Rev. 0 (Sala eléctrica # 602)

• Plano 2325-3500-265-DW-4301, Rev. 0 (Sala eléctrica # 606)

• Plano 2325-3600-265-DW-4301, Rev. 0 (Sala eléctrica # 608)

• Plano 2325-3600-265-DW-4302, Rev. 0 (Sala eléctrica # 609)

• Plano 2325-3700-265-DW-4301, Rev. B (Sala eléctrica # 610)

• Plano 2325-3700-265-DW-4302, Rev. B (Sala eléctrica # 613)

• Plano 2325-3700-265-DW-4303, Rev. B (Sala eléctrica # 612)

• Plano 2325-3700-265-DW-4304, Rev. B (Sala eléctrica # 615)

• Plano 2325-3700-265-DW-4305, Rev. B (Sala eléctrica # 611)

• Plano 2325-3700-265-DW-4306, Rev. B (Sala eléctrica # 614)

• Plano 2325-6930-265-DW-4301, Rev. 0 (Estación de bombeo # 1, ER # 101)

• Plano 2325-6940-265-DW-4301, Rev. 0 (Estación de bombeo # 2, ER # 102)

• Plano 2325-6950-265-DW-4301, Rev. 0 (Estación de bombeo # 3, ER # 103)

• Plano 2325-6960-265-DW-4301, Rev. 0 (Estación de bombeo # 4, ER # 104)

• Criterio de Diseño Eléctrico, documento No. 2325-0000-265-DC-0001, Rev. 0.

Page 5: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Página 4 de 5 PROYECTO N° 232500 Enero, 2005 REV. 0 FLUOR

5.0 NORMAS

Norma IEEE Std. 80, año 2000

6.0 BASES DE CÁLCULO

Las mallas del área EW y SX son calculadas en forma individual. En el área de pilas de LX se considera, para el cálculo, que las mallas de puesta a tierra de las subestaciones móviles están conectadas con la malla de la subestación principal SX, a través del cable de guardia de la línea de 13.8 [kV].

Los valores de cortocircuito utilizados para el diseño de las mallas corresponden al nivel de 13.8 [kV]. En el área EW, la corriente de falla a tierra esta limitada a 200 [A] por los reactores Zig-Zag. En el área de SX, la corriente de falla a tierra esta limitada a 200 [A] por las resistencias de neutro de los transformadores de poder.

Adicionalmente, la corriente de falla a tierra considera el efecto limitador de la propia resistencia de la puesta a tierra y del cable de guardia donde sea aplicable. Los valores finalmente utilizados en el cálculo de las mallas se indican en el Anexo 1.

El tiempo de despeje de falla es 1.0 [s]. Corresponde a la protección de respaldo en la sala eléctrica correspondiente. (Cuatro pasos de coordinación de 0.25 [s] cada uno).

Para la Planta de Inoculación, el tiempo de despeje de falla está limitado a 0.1 [s] por el reconectador Tag No. 7100-7W15-602.

En EW, se utilizó el valor de 2,000 [Ohm-m] como resistividad de la capa superior, considerando que habrán movimientos de tierra y rellenos compactados. Como espesor de la capa superior se consideraron 7.0 [m] como promedio. Como resistividad del sustrato se utilizó el valor medido (230 [Ohm-m]).

En SX, se utilizó el valor de 2,000 [Ohm-m] como resistividad de la capa superior, considerando que habrán movimientos de tierra y rellenos compactados. Como espesor de la capa superior se consideraron 2.0 [m] como promedio. Como resistividad del sustrato se utilizó el valor medido para la tercera capa (200 [Ohm-m]).

7.0 METODOLOGÍA DE CÁLCULO

El programa de cálculo utilizado es el ETAP Power Station, Versión 4.7.0C, utilizando la metodología y procedimientos de cálculo desarrollados en la Norma IEEE Std. 80, año 2000.

8.0 RESULTADOS

El resumen de las mallas de puesta a tierra calculadas, se entrega en el Anexo 1 (1 hoja).

El resultado entregado por el ETAP para cada malla de puesta a tierra calculada, se entrega en el Anexo 2 (3 hojas por cada cálculo de malla).

Page 6: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Página 5 de 5 PROYECTO N° 232500 Enero, 2005 REV. 0 FLUOR 9.0 CONCLUSIONES

Las mallas de puesta a tierra diseñadas, cumplen con las exigencias de seguridad sobre tensiones de paso y de contacto, establecidas en la Norma IEEE Std. 80, año 2000.

Los valores obtenidos para las resistencias de cada malla son menores a los 25 [Ohm] establecidos en el documento No. 2325-0000-265-DC-0001, “Criterio de Diseño Eléctrico”, con excepción de las salas # 608 y # 609 de la Planta EW, donde se calcularon 34.90 [Ohm]. Se estima que al utilizar el producto KAM, esta resistencia deberá quedar bajo los 25 [Ohm], de acuerdo con la información técnica del producto.

Ingendesa realizó un estudio de la interconexión de las mallas de puesta a tierra, tanto para la planta EW como SX. El resultado obtenido confirma el buen comportamiento de las mallas interconectadas. (Ver Anexo 4).

10.0 RECOMENDACIONES

La totalidad de la superficie de las mallas deberán estar cubiertas por una capa de grava de 15 [cm] de espesor, con una resistividad mínima de 5000 [Ohm-m].

Debido a los malos valores de resistividades del terreno, y aunque las mallas calculadas cumplen con el valor de resistencia de malla máxima de 25 [Ohm] sin considerar aditivos, (ver párrafo 8), es recomendable el uso del producto KAM, consistente en un tratamiento artificial reductor de resistencias de puesta a tierra.

Page 7: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Enero, 2005 PROYECTO N° 232500 REV. 0 FLUOR

ANEXO 1 RESUMEN DE RESULTADOS

Page 8: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LTDA. MEMORIA DE CALCULO No. 2325-0000-265-CS-0007PROYECTO LIXIVIACION DE SULFUROS 04/01/05PROYECTO No. 2325 REV. 0

RESUMEN DISEÑO DE MALLAS DE TIERRA Salas Eléctricas EW Salas Eléctricas SX Móviles SX

DESCRIPCION Unidad 610, 611-612,613 y 614-615 608 609 606 601 602 627 S. House

NorteS. House

SurS/E Móvil

NorteS/E Móvil

Sur

Longitud X Lx m 82 35 35 30 30 25 25 16 21 26 25.7

Longitud Y Ly m 20 24 24 25 20 42 15 12 8 19.3 27.3

Conductores en X Nx c/u 4 7 7 7 6 9 5 5 4 4 5

Conductores en Y Ny c/u 9 8 8 8 9 5 10 6 8 6 6

Area de la malla S m2 1,640 840 840 750 600 1,050 375 192 168 502 702

Radio equivalente r m 22.8 16.4 16.4 15.5 13.8 18.3 10.9 7.8 7.3 12.6 14.9

Longitud total conductor L m 508 437 437 410 360 435 275 152 148 220 292

Resistividad del suelo capa superior Rho Ohm-m 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000 2,000

Espesor capa superior e m 7.0 7.0 7.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0

Resistividad del suelo capa inferior (sustrato) Rho Ohm-m 230 230 230 200 200 200 200 200 200 200 200

Resistencia de Malla (Laurent) Rm Ohm 25.8 35.2 35.2 37.2 41.7 31.9 53.0 77.1 81.9 48.7 40.3

Cantidad barras (copperweld de 19 mm x 3 metros) N c/u 4 4 4 4 4 4 4 4 4 4 4

Resistencia combinada Malla+Barras (<25 Ohm) Rm Ohm 23.54 34.90 34.90 18.64 19.60 17.07 21.71 24.85 24.95 20.68 19.16

Voltaje del sistema Vs kV 13.8 13.8 13.8 13.8 13.8 13.8 13.8 13.8 13.8 13.8 13.8

Sobrevoltaje sistema pu 1 1 1 1 1 1 1 1 1 1 1

Resistencia de neutro sistema Rn Ohm 40 40 40 40 40 40 40

Rectancia (Zig-Zag) Xn Ohm 40 40 40

Corriente de falla máxima Ig A 199 199 199 200 200 200 2100 200 200 200 200

Corriente de falla ajustada con resistencia de PAT Ig A 172 150 150 136 134 140 367

Resistencia cables de guardia Rc Ohm 10 10 10 10

Corriente de falla considerando interconexión (*) Ig A 49 49 56 59

Tiempo despeje de falla s 1.0 1.0 1.0 1.0 1.0 1.0 0.1 1.0 1.0 1.0 1.0

Factor de diseño 1 1 1 1 1 1 1 1 1 1 1

Corriente de Falla para diseño A 175 155 155 160 150 160 400 80 80 80 80

(*) : Se considera la conexión con la malla de tierra de la subestación principal a través de los cables de guardia.

Page 9: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Enero, 2005 PROYECTO N° 232500 REV. 0 FLUOR

ANEXO 2 REPORTES DEL ETAP

Page 10: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: SALA#608

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #608

IEEE Std 80-2000

Number of Ground Conductors: 15

Number of Ground Rods: 4

Total Length of Ground Conductors: 437.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SALA#608

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\EW-Sala#608\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 11: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: SALA#608

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #608

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.150 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 7.00 Dry soil 230.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 35.0 24.0 7 8 Shape: Rectangular 5.0 4.0 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

15 437.0 $43,700 4 12.0 $400 $44,100

Page 12: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: SALA#608

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #608

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

34.897 5235.3 761.6 865.5 555.8 3114.2 88.0 17.8

Total Fault Current: 0.150 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.150 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 13: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: SALA#609

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #609

IEEE Std 80-2000

Number of Ground Conductors: 15

Number of Ground Rods: 4

Total Length of Ground Conductors: 437.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SALA#609

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\EW-Sala#609\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 14: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: SALA#609

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #609

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.150 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 7.00 Dry soil 230.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 35.0 24.0 7 8 Shape: Rectangular 5.0 4.0 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

15 437.0 $43,700 4 12.0 $400 $44,100

Page 15: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: SALA#609

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #609

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

34.897 5235.3 761.6 865.5 555.8 3114.2 88.0 17.8

Total Fault Current: 0.150 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.150 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 16: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: SALAS#610-a-615

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

MALLA DE TIERRA SALAS ELECTRICAS #s 610, 611-612, 613 Y 614-615

IEEE Std 80-2000

Number of Ground Conductors: 13

Number of Ground Rods: 4

Total Length of Ground Conductors: 508.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SALAS#610-a-615

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\EW-Salas#610-a-615\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 17: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: SALAS#610-a-615

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

MALLA DE TIERRA SALAS ELECTRICAS #s 610, 611-612, 613 Y 614-615

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.150 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 7.00 Dry soil 230.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 82.0 20.0 4 9 Shape: Rectangular 10.3 6.7 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

13 508.0 $50,800 4 12.0 $400 $51,200

Page 18: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA EW

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: SALAS#610-a-615

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

MALLA DE TIERRA SALAS ELECTRICAS #s 610, 611-612, 613 Y 614-615

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

23.542 3531.9 730.6 865.5 334.7 3114.2 84.4 10.7

Total Fault Current: 0.150 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.150 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 19: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: SALA#601

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #601

IEEE Std 80-2000

Number of Ground Conductors: 15

Number of Ground Rods: 4

Total Length of Ground Conductors: 360.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SALA#601

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\SX-Sala#601\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 20: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: SALA#601

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #601

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.150 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 2.00 Dry soil 200.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 30.0 20.0 6 9 Shape: Rectangular 3.7 4.0 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

15 360.0 $36,000 4 12.0 $400 $36,400

Page 21: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: SALA#601

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #601

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

19.597 2940.0 855.0 865.5 694.5 3114.2 98.8 22.3

Total Fault Current: 0.150 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.150 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 22: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: SALA#602

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #602

IEEE Std 80-2000

Number of Ground Conductors: 14

Number of Ground Rods: 4

Total Length of Ground Conductors: 435.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SALA#602

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\SX-Sala#602\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 23: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: SALA#602

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #602

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.160 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 2.00 Dry soil 200.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 25.0 42.0 9 5 Shape: Rectangular 6.3 5.3 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

14 435.0 $43,500 4 12.0 $400 $43,900

Page 24: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: SALA#602

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #602

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

17.074 2732.3 847.7 865.5 508.5 3114.2 97.9 16.3

Total Fault Current: 0.160 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.160 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 25: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: SALA#606

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #606

IEEE Std 80-2000

Number of Ground Conductors: 15

Number of Ground Rods: 4

Total Length of Ground Conductors: 410.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SALA#606

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\SX-Sala#606\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 26: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: SALA#606

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #606

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.160 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 2.00 Dry soil 200.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 30.0 25.0 7 8 Shape: Rectangular 4.3 4.2 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

15 410.0 $41,000 4 12.0 $400 $41,400

Page 27: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: SALA#606

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SALA ELECTRICA #606

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

18.638 2982.6 842.6 865.5 644.4 3114.2 97.4 20.7

Total Fault Current: 0.160 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.160 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 28: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: INOCULACION

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - PLANTA DE INOCULACION

IEEE Std 80-2000

Number of Ground Conductors: 15

Number of Ground Rods: 4

Total Length of Ground Conductors: 275.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: INOCULACION

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\SX-Inoculacion\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 29: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: INOCULACION

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - PLANTA DE INOCULACION

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.400 0.10 0.10 0.10 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 2.00 Dry soil 200.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 25.0 15.0 5 10 Shape: Rectangular 2.8 3.8 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

15 275.0 $27,500 4 12.0 $400 $27,900

Page 30: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: INOCULACION

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - PLANTA DE INOCULACION

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

21.705 8695.8 2709.9 2,737.1 2497.9 9847.8 99.0 25.4

Total Fault Current: 0.400 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.401 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.002

Page 31: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename:

SWITCH-HOUSE-NORTE

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SWITCH HOUSE PLATAFORMA NORTE

IEEE Std 80-2000

Number of Ground Conductors: 11

Number of Ground Rods: 4

Total Length of Ground Conductors: 152.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SWITCH-HOUSE-NORTE

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\SX-SwitchHouse-Norte\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 32: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename:

SWITCH-HOUSE-NORTE

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SWITCH HOUSE PLATAFORMA NORTE

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.080 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 2.00 Dry soil 200.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 16.0 12.0 5 6 Shape: Rectangular 3.2 3.0 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

11 152.0 $15,200 4 12.0 $400 $15,600

Page 33: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename:

SWITCH-HOUSE-NORTE

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SWITCH HOUSE PLATAFORMA NORTE

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

24.848 1988.2 828.6 865.5 756.5 3114.2 95.7 24.3

Total Fault Current: 0.080 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.080 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 34: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename:

SWITCH-HOUSE-SUR

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SWITCH HOUSE PLATAFORMA SUR

IEEE Std 80-2000

Number of Ground Conductors: 12

Number of Ground Rods: 4

Total Length of Ground Conductors: 148.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SWITCH-HOUSE-SUR

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\SX-SwitchHouse-Sur\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 35: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename:

SWITCH-HOUSE-SUR

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SWITCH HOUSE PLATAFORMA SUR

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.080 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 2.00 Dry soil 200.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 21.0 8.0 4 8 Shape: Rectangular 3.0 2.7 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

12 148.0 $14,800 4 12.0 $400 $15,200

Page 36: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename:

SWITCH-HOUSE-SUR

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SWITCH HOUSE PLATAFORMA SUR

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

24.951 1996.4 820.6 865.5 798.5 3114.2 94.8 25.6

Total Fault Current: 0.080 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.080 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 37: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: SE-MOVILES-NORTE

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SUBESTACIONES MOVILES PLATAFORMA NORTE

IEEE Std 80-2000

Number of Ground Conductors: 10

Number of Ground Rods: 4

Total Length of Ground Conductors: 220.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SE-MOVILES-NORTE

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\SX-SE-Moviles-Norte\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 38: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: SE-MOVILES-NORTE

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SUBESTACIONES MOVILES PLATAFORMA NORTE

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.080 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 2.00 Dry soil 200.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 26.0 19.3 4 6 Shape: Rectangular 5.2 6.4 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

10 219.8 $21,980 4 12.0 $400 $22,380

Page 39: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: SE-MOVILES-NORTE

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SUBESTACIONES MOVILES PLATAFORMA NORTE

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

20.676 1654.4 716.9 865.5 404.0 3114.2 82.8 13.0

Total Fault Current: 0.080 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.080 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 40: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 1

SN: 88FDI30132

Filename: SE-MOVILES-SUR

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SUBESTACIONES MOVILES PLATAFORMA SUR

IEEE Std 80-2000

Number of Ground Conductors: 11

Number of Ground Rods: 4

Total Length of Ground Conductors: 292.00 m

Total Length of Ground Rods: 12.00 m

Frequency: 50.0

Unit System: Metric

Project Filename: SE-MOVILES-SUR

Output Filename: D:\ETAP470\PowerStation\2325-Mallas de tierra\SX-SE-Moviles-Sur\Grid1_Untitled.GR1

Ground Grid Systems

ETAP PowerStation

Electrical Transient Analyzer Program

Page 41: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 2

SN: 88FDI30132

Filename: SE-MOVILES-SUR

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SUBESTACIONES MOVILES PLATAFORMA SUR

Ground Grid Input Data

System Data:

kg

for

Factor

Fault

Factor

CpSf TsTc

kA

Total

Body CurrentConductorsDuration °C

Available

for

Tf

Ground

for Sizing

Total Fault

Fault Duration (Seconds)

%

Projection

%

Division

X/R

Short-Circuit Current

Current

Ambient

Temp.WeightFreq.

Hz

50.0 50 40.00 0.10 0.080 1.00 1.00 1.00 100.0 100.0

Soil Data:

mmW.m W.mW.m

Resistivity

Lower Layer Soil

Resistivity Depth

MaterialTypeMaterial Type

Upper Layer Soil

DepthResistivity

Surface Material

Material Type

Gravel 5000.0 0.15 Dry soil 2000.0 2.00 Dry soil 200.0

Type %

Conductivity

1/°C

@ 20 °C

ar Factor

K0 @

0 °C

Temperature

Fusing

°C

Resistivity of

Ground Conductor

@ 20°C

mW.cm

Capacity

Per Unit Volume

J/(cm³.°C)

Thermal

Conductor/Rod

Material Constants:

Copper, annealed soft-drawn 100.0 0.00393 234.0 1083.0 1.72 3.42Conductor & Rod

Rod Data:

m Rods $/Rod

Cost

Arrangement

No. ofLength

cm

Diameter

1.9 3.0 4 Rods in Grid Corners 100.0

Grid Configuration:

mm² Lx Ly Direction

Grid Length m

Depth

m

Size

Conductor

in X

Direction

in Y

Number of Conductors

Direction

in X

Direction

in Y

Separation m

$/m

Cost

95 0.7 25.7 27.3 5 6 Shape: Rectangular 5.1 6.8 100.00

Cost:

Total

CostCostm

Total LengthTotal

No.

RodConductor

Costm

Total LengthTotal

No.

11 292.3 $29,230 4 12.0 $400 $29,630

Page 42: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Location: MINERA ESCONDIDA - PLANTA SX

Engineer: FLUOR CHILE S.A. Study Case: GRD1

4.7.0C

Page: 3

SN: 88FDI30132

Filename: SE-MOVILES-SUR

Project: LIXIVIACION DE SULFUROS

ETAP PowerStation

Contract: 2325

Date: 12-01-2004

DISEÑO DE MALLA DE TIERRA - SUBESTACIONES MOVILES PLATAFORMA SUR

Ground Grid Summary Report

%

Calculated

%

CalculatedPotential Rise

Rg

Step PotentialTouch Potential

VoltsVoltsVoltsVolts

Tolerable CalculatedTolerable Calculated

Volts

Ground

GPR

Ohm

Resistance

Ground

19.162 1533.2 582.1 865.5 329.6 3114.2 67.3 10.6

Total Fault Current: 0.080 kA Reflection Factor (K): -0.429

Maximum Grid Current: 0.080 kA Surface Layer Derating Factor (Cs): 0.862

Decrement Factor (Df): 1.000

Page 43: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Enero, 2005 PROYECTO N° 232500 REV. 0 FLUOR

ANEXO 3 RESUMEN MEDICIONES DE RESISTIVIDAD EN ESCONDIDA

Page 44: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Sondeo Lugar ρ1 e1 ρ2 e2 ρ3 e3 ρ4 e4 ρ sustrato e sustrato

[Ωm] [m] [Ωm] [m] [Ωm] [m] [Ωm] [m] [Ωm] [m]

1 S/E Bombeo 2 55 k 0,95 m 8,5 k 2,85 m 2,0 k 0,95 m - - 20 infinito

2 S/E Bombeo 2 180 k 0,50 m 1,8 k 5,00 m - - - - 110 infinito

3 S/E Bombeo 3 700 k 0,90 m 9 k 4,50 m 50,0 k 2,70 m - - 700 infinito

4 S/E Bombeo 3 900 k 1,20 m 22 k 7,20 m - - - - 1.500 infinito

5 S/E Bombeo 4 30.000 k 0,80 m 800 k 1,60 m 100,0 k 8,00 m - - 4.000 infinito

6 S/E Bombeo 4 18.000 k 2,00 m 1.000 k 4,00 m - - - - 3.500 infinito

7 N-118.300 E-15.500 13 k 0,60 m 2,8 k 1,20 m 5,5 k 4,20 m - - 1.400 infinito

8 N-116.800 E-14.000 18 k 0,80 m 6,5 k 2,40 m 1,2 k 4,00 m - - 300 infinito

9 N-115.300 E-13.000 6,5 k 0,40 m 0,1 k 0,80 m 0,8 k 4,80 m - - 200 infinito

10 N-113.000 E-14.200 6,0 k 0,50 m 1,4 k 1,00 m 5,0 k 4,00 m - - 100 infinito

11 N-111.600 E-13.700 6,5 k 0,60 m 0,3 k 3,00 m - - - - 800 infinito

12 S/E Súlfuros N-S 15 k 0,50 m 5,0 k 2,50 m 2,5 k 2,50 m - - 230 infinito

13 S/E Súlfuros E-O 15 k 0,30 m 5,0 k 2,10 m 2,5 k 5,40 m - - 230 infinito

14 N-112.300 E-14.500 6,5 k 0,60 m 0,3 k 3,00 m - - - - 800 infinito

15 N-111.500 E-17.000 100 k 0,50 m 1,4 k 5,00 m - - - - 200 infinito

16 N-111.500 E-19.000 0,05 k 0,90 m 4,5 k 1,80 m - - - - 25 infinito

17 N-111.500 E-20.500 4,5 k 1,00 m 5,0 k 3,00 m 2,0 k 5,00 m - - 120 infinito

18 N-111.500 E-21.500 10 k 0,50 m 6,0 k 1,50 m 0,8 k 2,50 m 3,0 k 10,00 m 200 infinito

19 N-110.500 E-22.300 4,6 k 0,60 m 1,1 k 6,00 m 0,4 k 1,80 m - - 150 infinito

20 N-109.000 E-22.700 2,6 k 0,80 m 0,73 k 4,80 m - - - - 220 infinito

21 S/E Lixiviación (1) 0,6 k 0,60 m 1,6 k 1,80 m 0,2 k 4,80 m - - 60 infinito

22 S/E Lixiviación (2) 0,55 k 2,00 m 0,3 k 4,00 m - - - - 60 infinito

Nota: Sustrato es la capa más profunda del corte geoeléctrico.

La resistividad está expresada en [ ohm m ]. El sufijo "k" representa a [ kilo ohm m ].

S/E Lixiviación (1) y (2) son dos posiciones, separadas unos 50 [m] entre sí, en el sector asignado a dicha subestación.

RESULTADOS CAMPAÑA DE MEDICIÓN DE RESISTIVIDAD EN ESCONDIDA (marzo - mayo 2004)

Page 45: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

MINERA ESCONDIDA LIMITADA Memoria de Cálculo N° 2325-0000-265-CS-0007 PROYECTO LIXIVIACIÓN DE SÚLFUROS Enero, 2005 PROYECTO N° 232500 REV. 0 FLUOR

ANEXO 4 RESULTADOS DEL ANALISIS DE LA INTERCONEXION DE MALLAS DE PUESTA A

TIERRA (CORREO ELECTRONICO DE INGENDESA)

Page 46: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Cesar Pontt10-06-2004 15:44

To: Jaime Munoz/SN/FD/FluorCorp@FluorCorp

cc: Roberto Falck/SN/FD/FluorCorp@FluorCorp

Subject: Envío del resultado del análisis de la Interconexión de Mallas de Tierra.Lixiviación de sulfuros.

.....

----- Forwarded by Cesar Pontt/SN/FD/FluorCorp on 06/10/2004 03:51 PM -----

"Jofre Olate, Guillermo Reinaldo, INGENDESA" <[email protected]>06/10/2004 03:55 PM

To: [email protected]

cc: "Gonzalez Gomez, Sergio Ivan, INGENDESA" <[email protected]>

Subject: Envío del resultado del análisis de la Interconexión de Mallas de Tierra.Lixiviación de sulfuros.

.....

César:

A continuación nuestros comentarios de las mallas interconectadas deSulfuros y Lixiviación.

1. Malla interconectada de Sulfuros.

Se ha simulado en CYMGRD, la totalidad de las mallas presentadas en losplanos de Fluor N°2325-4700-265-DW-4303 "Proyecto lixiviación de sulfuros.Electrobtención. Interconexión malla de puesta a tierra. Planta." El valorcalculado de resistencia de puesta a tierra de las mallas interconectadases: 2.50 ohm.

Adicionalmente, se han verificado las condiciones de seguridad de latotalidad de las mallas interconectadas y hemos detectado que en la Sala deCalentadores y en el Edificio de Electrobtención la tensión de contacto estapor sobre lo permitido por la norma IEEE Std 80. En este sentido, cuandosimulamos las mallas del plano N°2325-4700-265-DW-4303, agregando losconductores indicados en el plano revisado, las tensiones de contacto detodos los sectores interconectados quedan dentro de lo permitido por lanorma IEEE Std 80.

Se concluye que de acuerdo al plano N°2325-4700-265-DW-4303, para cumplircon lo exigido en la norma IEEE Std 80, se deben realizar las modificacionesindicadas en el.

2. Malla interconectada de Lixiviación.

Se ha simulado en CYMGRD, la totalidad de las mallas presentadas en losplanos de Fluor N°2325-4700-265-DW-4304 "Proyecto lixiviación de sulfuros.Area planta SX - Piscinas PLS / Refino. Interconexión malla de puesta atierra. Planta." El valor calculado de resistencia de puesta a tierra de lasmallas interconectadas es: 2.20 ohm.

Adicionalmente, se han verificado las condiciones de seguridad de latotalidad de las mallas interconectadas, comprobándose que todos lossectores interconectados cumplen con los requisitos de seguridad de la normaIEEE Std 80.

Page 47: 2325-0000-265-CS-0007-0 - Calc Mallas Puesta a Tierra).pdf

Se concluye que de acuerdo al plano N°2325-4700-265-DW-4304, se cumple conla norma IEEE Std 80 y no sería necesario modificarlo.

Atentamente,

Guillermo Jofré OlateTeléfonos: 634 7266 (anexo 4286) 630 8286 (directo)Faxes : 635 4070 (central) 665 1810 (directo)