A - Interior Design Works - UNHCR PAKISTAN · A - Interior Design Works S.NO. DESCRIPTION OF ITEM QTY. UNIT 1 Demolition & Dismantling a) Block Masonry Walls Demolition of highlighted

ANNEX B – BILL OF QUANTITIES (BOQs) SC/RFP/19/037

Page 1 of 20

A - Interior Design Works

S.NO. DESCRIPTION OF ITEM QTY. UNIT

1 Demolition & Dismantling

a) Block Masonry Walls

Demolition of highlighted block masonry walls including removing of non-required conduits, wires, pipes, disposing the debris from the site etc. complete in all respect.

2544 SFT

b) Flooring

Demolition and extraction of existing flooring along with 3" CC Bed, including removal of non-required conduits, wires, pipes, chipping of existing surface, removal of debris from site etc. complete in all respect.

7370 SFT

c) Raised Floor

Demolition and extraction of existing 12" raised flooring along with CC Bed, including removal of non-required conduits, wires, pipes, chipping of existing surface, removal of all plumbing and debris from site etc. complete in all respect.

475 CFT

d) Doors & Windows

Dismantling and removal of highlighted existing doors and windows including removal of hold fasts, hardware, door and window frames and panels, removal of debris from site etc. complete in all respect.

i Doors 22 NOS

ii Windows & Ventilators 44 NOS

e) Tiles

Removing and chipping of existing dado tiles, in bathrooms, corridors, wards as specified, including cutting, chipping of plaster / bond, removing of debris from site complete in all respect.

3972 SFT

f) Fumigation

Fumigation of entire floor working area along with vertical bathroom plumbing shaft of entire building (6 Floors) with minimum 2-years warranty, fumigated by specialist vendors as approved by Architects / Hospital Management.

1 JOB

2 Block Masonry


Page 2 of 20

Provide and lay machine made block masonry of approved quality at any height, in line level and plumb, setting the blocks in 1:6 cement sand mortar, including filling joints, pointing, niche, curing, placing, scaffolding, including appropriate steel anchors tied to RCC columns/walls, hacking of existing surface for bonding where necessary, wastage, etc., complete in all respect as per drawings specifications and directed by architect, including the cost of anchors (The compressive strength shall be minimum 1000 psi for blocks).

6" thick Solid 2300 SFT

8" thick Solid 2600 SFT

3 Plaster

Provide and apply 1:5 cement sand plaster including G.I. corner beads / plaster stops (all horizontal and vertical exposed corner edges up to required height from FFL), 300mm wide galvanized metal lathe of 18 SWG at the junctions of concrete and block masonry, conduit chases, etc., fixed with masonry nails and G.I. sheet strip, rounded edges where required, grooves where required, smooth finished in line, level, plumb, curing, scaffolding, hacking / chipping of existing surface for bonding where necessary, etc., complete as per drawings, specifications and as directed by the Architects.

1/2" thick 11025 SFT

4 RCC Lintels

Providing, making and placing 6" x 12" reinforced cement concrete lintel complete as per drawings, specifications and as directed by the Architects. This rate also includes all kinds of forms, moulds, lifting, shuttering, curing, rendering, cost of steel reinforcement and finishing the exposed surface (including screening and washing of aggregate).

R.C.C. Lintels 1:2:4 (fc 3000 psi) 150 RFT

5 Paint Works

a) Matt Enamel Paint

Provide and apply Matt Enamel paint (ICI / Jotun) minimum three coats of approved shade over a coat of primer on plastered surface prepared smooth with carborandum stone, filling and the depression with putty including preparation of base etc., complete in all respect as per drawings specifications and as instructed by architect.

7200 SFT

b) Anti-Bacterial Paint


Page 3 of 20

Provide and apply Anti-Bacterial paint (ICI / Jotun) minimum three coats of approved shade over a coat of primer on plastered surface prepared smooth with carborandum stone, filling the depression with putty including preparation of base etc., complete in all respect as per drawings specifications and as instructed by architect.

12500 SFT

c) Vinyl Emulsion Paint

Provide and apply Vinyl Emulsion paint (ICI / Berger) minimum three coats of approved shade over a coat of primer to internal surfaces prepared smooth with carborandum stone, filling the depression with putty including preparation of base including scaffolding, etc. complete in all respect as per drawings specifications and as instructed by architect.

4800 SFT

6 Raised Floor

Provide and construct Raised Floors consisting of following items. (For payment, sub-floor area will be measured)

i- Solid block masonry at the periphery (4" thick)

ii- 1/2" thick 1:4 plaster on walls

iii- Provide and lay in position inverted clay pots

iv- Provide and fill charcoal as per required level

v- Provide and lay 3" 1:3:6 cement concrete floor in required slope

a) 6" Thick From Corridor F.F.L. 200 SFT

b) 12" Thick From Corridor F.F.L. 380 SFT

7 Water Proofing

Water proofing in toilet with up to 7 feet height Cementitious waterproofing treatment by brush application of ICS / Penetron International Ltd or approved equivalent on floor and walls including treatment at the junctions of horizontal & vertical surface, etc., complete in all respect as per drawings and instructions of the Architect.

1500 SFT

8 Porcelain Tile Flooring


Page 4 of 20

Provide and laying large format full body Porcelain tile (3' x 6' or 4' x 8') of approved sample for flooring, in slope if required, with 1:4 cement sand mortar base of required thickness so as to achieve a minimum overall finished floor thickness of 75mm, setting the tiles with neat cement mortar, grouting the butt joints with approved grout of approved colour (Ressichem or approved equivalent) as per manufacturer's specifications & instructions, including curing, cleaning, hacking / chipping of existing surface for bonding where necessary, etc., complete in all respect as per drawings specifications and as instructed by architect.

a) PT - 01: Basic Rate Rs. 400/sft 7370 SFT

Same as item # 10. above but in bathroom floor and on walls with 1/2" rough plaster, including sealing the joints with Nitoflor FC100 of Fosroc or approved equivalent as per manufacturer's specifications & instructions.

b) PT - 02: Basic Rate Rs. 300/sft 1800 SFT

9 Skirting

Provide and install in position where required, 65mm high approved quality heavy duty PVC skirting (Kaysons, Sarina or approved equivalent) with approved adhesive, etc, complete in all respect as per drawings, specifications and as instructed by the Architect. Base Rate: 280 Rs / Rft

2200 RFT

10 Gypsum Ceiling

Provide and install in position suspended ceiling, consisting of 1/2" thick Gypsum Board (Elephant brand Thailand or approved equivalent) with G.I. suspension system including M.S. Rod hangers red oxide treated with 1ʺx 1ʺ & ½ʺx½ʺ GI angle & 1ʺx 1ʺ T section as shown in drawing including the cost of flush band, cutting of opening for light fixtures / diffusers with making light pelmet/cove of any size in 3/4" thick MDF with rough wood framing including all fixing arrangements, fiber tape on joints, 3 coats of Matt Enamel paint finish (ICI or Berger), primer coat, filling if required with all hardwares, wastage, etc., complete in all respect as per drawings, specifications and as instructed by the Architect. (For payment net flat surface will be measured and Light fixtures & A/C diffusers will be deducted. The rate should include making of light cove/pelmet in MDF).

6500 SFT

11 Aluminium Openable Ceiling


Page 5 of 20

Providing and installing in position aluminium openable slatted ceiling, including 2" x 1" powder coated aluminium slat sections, with 2" gap between sections, fixed in openable frames of 4 ft by 4 ft with SS openable hinges at every 4 ft intervals, in corridor area, powder coated finish in approved colors, cutting, joining, fixing, imported hardware (JB Saeed or equivalent) complete in all respect.(For payment exposed surface area will be measured)

800 SFT

12 MR Gypsum Ceiling

Provide and install in position suspended ceiling, consisting of 1/2" thick Moisture Resistant Gypsum Board (Elephant brand Thailand) with G.I. suspension system including M.S. Rod hangers red oxide treated with 1ʺx 1ʺ & ½ʺx½ʺ GI angle & 1ʺx 1ʺ T section as shown in drawing including the cost of flush band, cutting of opening for light fixtures / diffusers including all fixing arrangements, fiber tape on joints, 3 coats of Matt Enamel paint finish (ICI or Berger), primer coat, filling if required with all hardwares, wastage, etc., complete in all respect as per drawings, specifications and as instructed by the Architect. (For payment net flat surface will be measured and Light fixtures & A/C diffusers will be deducted. The rate should include making of light cove/pelmet in MDF).

550 SFT

13 Gypsum Access Panels

Provide and install 2'x2' gypsum access panel comprising of 1/2" thick gypsum sheet with GI frame and suspension system including all required fixing arrangements, openable mechanism, 3 coats of matt enamel paint complete with all respect as per drawings, specifications as instructed by Architect.

30 NOS.

14 Fixed Glazing

Provide and install in position Fixed Glazing consisting of 12mm thick Tempered Clear Glass (Emirates Glass or approved equivalent) of approved sample, with 2mm thick 2" x 4" aluminium frame sections (Pakistan Cables Aluminium or Equivalent) charcoal grey anodization, including silicon sealant, approved rubber gasket, with all hardwares, wastage, cutting, lifting, scaffolding, white frosting as approved etc, complete as per drawing and instruction of the Architect. (For payment, net exposed Elevation Glazing area will be measured.)

1800 SFT

15 SS Glass Protection Bump Rail


Page 6 of 20

Providing and installing 6" high Stainless Steel protection bump rail in front of all interior glass partitions, including 1" x 1" SS pipe in 10swg, cutting of pipe, argon gas welding, fixing with SS bolts and hardware / accessories, brushed matt SS finish complete in all respect, as approved by the Architect.

400 RFT

16 SS Glass Protection Dado Rail

Providing and installing Stainless Steel protection guard rail in front of all interior glass partitions (both sides) and on walls, including 6" x 1/2" wide solid rail, including cutting of sheet, argon gas welding, fixing with SS bolts and hardware / accessories, chamfered edges, brushed matt SS finish complete in all respect, as approved by the Architect.

300 RFT

17 Windows & Ventilators

Provide & install openable & fixed windows and ventilators with flymesh as per drawings, consisting of 2mm thick aluminium frame sections of 2" x 4" and approved sample (Pakistan Cables Aluminium or Equivalent) as shown in drawing, 6mm +12mm gap + 6mm thick tempered tinted glass (Emirates or approved equivalent) in external windows & ventilators with UV Film, approved SS hardwares, lock set, latch, tower bolts, S.S hinges, sliding system of approved quality, including all hardwares, wastage, charcoal grey anodization etc., complete in all respect as per drawings specifications and as instructed by architect. (For payment, frame to frame area will be measured.)

a) W-1 (8'-6" x 6'-6") 20 NOS

b) W-2 (4' x 6'-6") 2 NOS

d) V-1 (5' x 6') 2 NOS

18 Blinds

Provide and install window blinds of approved sample (Protectors or approved equivalent) including lifting and fixing etc., complete in all respects as per drawings, specification instructions of the architect. Basic price of Blinds shall be Rs 350/sft

1200 SFT

19 Wood & Glass Doors


Page 7 of 20

Provide and install 40mm thick Glass door with Wooden Frame, comprising of 2" x 4" and 2" x 8" Oak Wood Sections door leaf, seasoned and solignum treated, 8mm thick tempered glass panels in center, using 2mm thick Charcoal grey Anodized Aluminium Door Frame (2" x 4", Pakistan Cables or approved equivalent), white polish finish on wood, white frosting on glass as approved, including all hardwares, stainless steel hinges / pivots, SS lock set, tower bolts, S.S Screw, S.S bar handles / SS turn handles / SS push plates, wastage, etc, complete in all respect as per drawings specifications and as instructed by architect. For payment, Frame to frame area will be measured. (Base Price of Hardware Rs 20,000 / door)

a) FD-01 (4'-6" x 6'-6") 5 NOS

b) FD-02 (3'-0" x 6'-6") 13 NOS

20 Wooden Flush Laminate Doors

Providing & fixing 40mm thick 50% solid core flush door comprising of 1/8" thick lamination board (Al-Noor or equivalent) pressed on both side on rough wood frame with 6mm thick Oak wood lipping all around, using 16 gauge Charcoal Grey Anodized Aluminium frame (2"x6"), as per door details, including all hardwares, S.S hinges, S.S Handles, S.S Push Plate, Lock Set, Tower Bolts, S.S screws, wastage, seasoning, termite proofing, S.S kick & push plate etc. Complete in all respect as per drawings, specifications and instructions of the architect.

a) GD-01 7 NOS

21 Counter Top in Pharmacy

Provide and install 3/4" thick chemically pre-polished approved Granite with rounded edge of approved sample, fixed with required adhesive over 3/4" thick MDF resting on rough wood frame with grouting & sealing the edges, etc. Complete in all respect as per directed by the Architect or Engineer Incharge. Basic Rate of Granite Rs.900/sft

10 SFT

22 Corrian Storage Ledges

Providing and installing 2" thick, 2' x 2' Corrian Ledges adjacent to every bed, fixed and embedded inside wall, including approved shade of DuPont Corrian wrapped all around, 3/4" Marine ply base inside, clean chamfered edges etc complete in all respect.

50 NOS.

23 Wooden Base & Hanging Cabinet


Page 8 of 20

Provide and install in position Laminate Cabinet, consisting of 3/4" thick laminated MDF shutter and shelves (Alnoor and equivalent), 1/8" thick Laminated MDF backing (Alnoor or equivelent), 1/8" thick PVC lipping, including all hardwares, hinges handles, lockset, wastage, cutting, lifting, etc., complete in all respect as per drawing, specifications and as instructed by the architect. (For payment, Elevation area will be measured)

a) Base Cabinet 800 SFT

b) Hanging Cabinet 600 SFT

24 Vertical Electrical Bed Panels

Providing, making and installing of 6 ft x 18" x 2" deep openable Vertical Electrical Bed Panels, including 14 Guage Powder Coated M/S sheet in 2 ft panels, 3/4" Marine Ply Base, approved SS Screws, 5 Nos Schnieder / Clipsal Switches and sockets on each panel, fixing, cutting, welding, chamfered edges, making holes for oxygen supply, as per drawings and as approved by the architect, complete in all respect.

50 NOS

25 MirrorProvide and install 5mm thick Belgium make mirror with 6mm thick commercial ply backing of approved quality, S.S stud fitting, including all hardwares, wastage, etc, complete in all respect as per drawing, specifications and as instructed by the

Provide and install 5mm thick Belgium make mirror with 6mm thick commercial ply backing of approved quality, S.S stud fitting, including all hardwares, wastage, etc, complete in all respect as per drawing, specifications and as instructed by the architect.

120 SFT

26 Toilet Accessories:

a) Hand dryer (Make Zilver or approved equivalent) 3 NOS

b) SS soap dispensers (Make Zilver or approved equivalent) 5 NOS

c) SS towel rack (Make Zilver or approved equivalent) 3 NOS

d) SS toilet paper holders (Make Zilver or approved equivalent) 6 NOS

e) Coat hooks (Make Zilver or approved equivalent) 12 NOS

f) Wall Mounted WC (Make Porta or approved equivalent) 6 NOS

g) Floor Mounted Hand Wash Basin (Make American Standard or approved equivalent)

6 NOS


Page 9 of 20

h) Wall Mounted Flushing Tank (Grohe or approved equivalent) 6 NOS

i) SS Clothes Line (JB Saeed or approved equivalent) 2 NOS

B - Electrical & Allied Works

ITEM # DESCRIPTION QTY UNIT

SECTION - A WIRING / WIRING ACCESSORIES

Supply, installation, testing & commissioning of following items including all , tools, labor etc required for completion of work as per specifications, details & drawings. Complete in all respects. Please note that all wires and cables shall be FR Cables.

SMALL WIRING FOR LIGHTS

A1 Circuit wiring from respective floor distribution board (DB) to switch board and between switch board to switch board using 2 x 2.5 sq.mm + ECC 1 x 2.5 sqmm, stranded Copper Conductor, color coded , single core PVC insulated wires in 25 mm dia pvc conduit surface or concealed in ceiling slab / wall or as required Complete in all respect as shown in the drawing.

20 No.

A2 Wiring for light point from switch board to first light / fan point using single core PVC insulated, stranded Copper Conductor, color coded wires of 1.5 sq.mm for phase, 2.5 sqmm for common neutral and 1.5 sqmm for common earth in 25 mm dia PVC conduit surface or concealed in ceiling slab / wall as required. Complete in all respect as shown in the drawing.

100 No.

A3 Wiring for light point from point to point using single core PVC insulated, stranded Copper Conductor, color coded wires of 1.5 sq.mm for phase, 2.5 sqmm for common neutral and 1.5 sqmm for common earth in appropriate size of PVC conduit surface/concealed in ceiling slab / wall as required. Complete in all respect as shown in the drawing.

100 No.

WIRING FOR GROUP CONTROL LIGHTS

A4 Wiring for group control light circuits from first light point to respective floor distribution board using following single core PVC insulated, stranded Copper Conductor, color coded wires in 25 mm dia PVC conduit concealed in ceiling slab / wall as required .

a 2 x 2.5 sqmm + ECC, 1 x 2.5 sqmm 3 No.

A5 Wiring for group control light point to light point using following single core PVC insulated, stranded Copper Conductor, color coded wires in 25 mm dia PVC conduit concealed in ceiling slab / wall as required.


Page 10 of 20


WIRING FOR EMERGENCY & EXIT LIGHTS

A6 Circuit wiring for Emergency point from respective floor distribution board (DB) to first light point using single core PVC insulated, stranded Copper Conductor, color coded wires of 2 x 2.5 sq.mm + ECC 1 x 2.5 sqmm in 25 mm dia PVC conduit concealed in ceiling slab / wall as required.

2 No.

A7 Wiring for Emergency light point to light point using single core PVC insulated, stranded Copper Conductor, color coded wires of 2 x 2.5 sq.mm + ECC 1 x 2.5 sqmm in 25 mm dia PVC conduit concealed in ceiling slab / wall as required.

6 No.

WIRING FOR INSECTICUTORS

A8 Circuit wiring for Insecticutors from respective floor distribution board (DB) to first point using single core PVC insulated, stranded Copper Conductor, color coded wires of 2 x 2.5 sq.mm + ECC 1 x 2.5 sqmm in 25 mm dia PVC conduit concealed in ceiling slab / wall as required.

1 No.

A9 Wiring for insecticutors from point to point using single core PVC insulated, stranded Copper Conductor, color coded wires of 2 x 2.5 sq.mm + ECC 1 x 2.5 sqmm in 25 mm dia PVC conduit concealed in ceiling slab / wall as required.

1 No.

SMALL WIRING FOR UTILITY POWER SOCKETS

A10 Circuit wiring from respective floor distribution board (DB) to 5/15 Switch Socket units (first outlet) using following size of single core PVC insulated stranded Copper Conductor, color coded wires in 25 mm dia pvc conduit embedded in floor, concealed in wall as required. Complete in all respect as shown in the drawing.


b 2 x 4.0 sqmm + ECC, 1 x 4.0 sqmm 5 No.

A11 Wiring for 13/15A Switch Socket units from outlet to outlet using following size of single core PVC insulated stranded Copper Conductor, color coded wires in 25 mm dia pvc conduit embedded in floor, concealed in wall as required.


SMALL WIRING FOR CONDITIONED POWER SOCKETS

A12 Circuit wiring from respective UPS Power panel (UDB) to 13A flat Switch Socket units (first outlet) using following size of single core PVC insulated stranded Copper Conductor, color coded wires in 25mm dia PVC conduit embedded in floor, concealed in wall as required Complete with all accessories as shown in the drawing.



Page 11 of 20

POWER WIRING FOR HAND DRYERS

A13 Wiring for Hand Dryers from respective floor distribution board (DB) to Unit using 3C, 2.5 sqmm PVC insulated stranded Copper Conductor, color coded wires in appropriate size of pvc conduit / already installed cable trays above false ceiling as shown in the drawings.

4 No.

A14 Wiring for Decorative Wall type Split Air-conditioning Units from respective floor DBs to indoor Evaporator or outdoor condensing unit at roof using following size of single core PVC insulated, color coded stranded Copper Conductor wires in 25 mm dia PVC conduit concealed in ceiling slab, wall as required Complete with all accessories as shown in the drawing.

a For 1.0 Ton Split AC Units 2 x 4 Sqmm + ECC, 1 x 4 Sqmm PVC

3 No.

b For 2.0 Ton Split AC Units 2 x 6 Sqmm + ECC, 1 x 6 Sqmm PVC

25 No.

SECTION - B

CABLE RACEWAYS / CONTAINMENT

Providing, fabrication, installation of following Solid / perforated type cable trays / Cable Ladders including cover as shown in the drawings. The cable routing solution must be made of 16 gauge metal sheet MS/Imported GI sheet, Rust Treated and Powder Quoted in required color including factory manufactured proper bends and Up links to ensure proper bend radius of cables. Item also includes all mounting accessories required to properly support the system suspended from ceiling slab / on wall brackets. All supporting system shall be painted with required color.

GI CABLE TRAYS POWDER COATED

B1 150mm x 100mm GI Cable Tray with Cover 100 Rft



CONDUITS & ACCESSORIES

Supply and installation of following size of PVC/UPVC conduits including all accessories such as junction box, bend, socket etc. Complete in all respect. Conduits for main sub main power and communication cabling. Item shall includes excavation, backfilling and compaction of floor upto the entire satisfaction of architect and consultant. Item includes duct banks for all conduits passing through the roads as per details and specifications.

PVC CONDUITS

B4 25mm dia PVC Conduit 1,500 Rft.


Page 12 of 20

B5 32mm dia PVC Conduit 1,000 Rft.

PULL BOXES / JUNCTION BOXES

B6 Supply and installation of following powder coated MS / GI Junction boxes / Intersection units including cover for power & communication cabling system as shown in drawings. The pull boxes shall be concealed in wall / surface type as prescribed and advised by the consultant.

B7 Flush Wall 200mm x 200 mm x 75 mm Pull Boxes for cable pulling like Data Junction Boxes, CCTV Junction Boxes, Ups power Junction Boxes (UDB), Communication Pull Boxes etc. with open able door type cover, made with 16SWG MS Sheet Powder Coated.

8 No.

SECTION - C

WIRING DEVICES / RECEPTACLES

Supply, installation and commissioning of following wiring devices / light control switches / power receptacles as per BS Standards including 16 SWG MS Powder Coated back boxes, flush with wall as shown in drawings and details.

LIGHT CONTROLLED SWITCHES

C1 One Gang 1 way 10A Switch 7 No.

C2 Two Gang 1 way 10A Switch 8 No.

C3 Three Gang 1 way 10A Switch 20 No.

C4 Four Gang 1 way 10A Switch 30 No.

C5 Five Gang 1 way 10A Switch 20 No.

FAN CONTROLLED DIMMERS

C6 One Gang Fan Dimmer 5 No.

C7 Two Gang Fan Dimmer 5 No.

UTILITY / CONDITIONED POWER RECEPTACLES

C8 13A, Multi Pin Switch Socket Unit 60 No.

C9 15A, Simplex Round 3-Pin Switch Socket Unit 30 No.

C10 13A, Simplex Flat 3-Pin Switch Socket Unit 50 No.

C11 13A, Duplex Flat 3-Pin Switch Socket Unit 50 No.

INDUSTRIAL SOCKETS WITH PLUGS

C12 16A 3-Pin Wall Industrial Sockets with male type connecting plugs

4 No.


Page 13 of 20

C13 32A 3-Pin Wall Industrial Sockets with male type connecting plugs

4 No.

SECTION - D

LIGHTING FIXTURES & FITTINGS

Supply, installation , testing and commissioning of following lighting fixtures including all accessories like electronic ballast, lamps, mountings steel rope etc. Complete in all respects.

D1 Recessed Ceiling LED Panel Light Fixture, 600x600mm having 45W LED Panel, 4000K as approved by architect.

100 No.

D2 Surface Ceiling / Wall mouted LED Batten Light Fixture, 1200mm having 28W LED, 4000K as approved by architect.

20 No.

D3 Recessed Ceiling round LED Down light Fixture, 18W, 4000K as approved by architect.

50 No.

EMERGENCY / EXIT LIGHTS/INSECTICUTORS

D4 Recessed Ceiling / Surface Self Contained Round Emergency Light having 1W LED as approved by architect.

10 No.

D5 Surface Ceiling / Wall Self Contained Emergency Light having 3W LED as approved by architect.

4 No.

INSECT KILLER LIGHTS

D6 Ceiling suspended two way insecticutor light complete with 2x20 watt UV lamps and base tray / collector as approved by architect.

4 No.

CEILING / WALL BRACKET / EXHAUST FANS

D7 Ceiling Mounted 2' x 2' Size of Fans (Voldam / Airflow) 35 No.

D8 Exhaust Fan 12" 10 No.

SECTION - E

DISTRIBUTION PANELS / SWITCHBOARDS

Supply, installation, testing and commissioning of following distribution panels in accordance with the attached single line diagrams and layout plans. The panels shall be made with 14/16 SWG sheet steel housing , powder coated after antirust primers. The Copper Bus Bars shall be tin electroplated with protective color coded heat shrink sleeves. All distribution panels shall for indoor installations but provided with gas kits. Contractor has to submit the shop drawings prior to fabrication for client's approval.

E1 DB LP 1 No.


Page 14 of 20

E2 DB UPS 1 No.

E3 DB AC 1 No.

SECTION - F

MAIN / SUB MAIN CABLES

Supply, installation, Testing, Termination and Commissioning of following single core / multi-core PVC insulated Copper Conductor Cables for main/sub-main power distribution system as shown in the schematic drawings in already installed Cable trays etc. Work also includes necessary termination accessories like compression lugs, color coded sleeves, identification tags etc.

Note : The quantities shown in the boq are estimated based on design drawings. Contractor has to take accurate measurements at site prior to procurement of material.

F1 FROM DB LP TO DB AC 4C, 50 Sqmm PVC/XLPE/PVC + ECC, 1x25 Sqmm PVC

120 Rft

F2 FROM DB LP TO DB UPS 4C, 25 Sqmm PVC/XLPE/PVC + ECC, 1x16 Sqmm PVC

120 Rft

F3 FOR UPS IN OR OUT CABLE 4C, 10 Sqmm PVC/PVC CABLE

100 Rft

SECTION - G

VOICE & DATA COMMUNICATION SYSTEM

Supply, installation , testing and commissioning of following items for voice and data communication system including all material , labor , tools , accessories etc. Complete in all respects. Item includes termination of all cables at respective patch panels / racks / TJBs as shown in the drawings and instructed by consultant.

HORIZONTAL VOICE & DATA CABLING

G1 Category 6 , UTP Cables, for data communication system at local workstations in 25mm dia PVC conduits/already installed cable trays as shown in the layout plan and schematic diagrams. Work includes all terminations, management and tagging at both ends.

4,000 Rft

G2 Category 6 , UTP Cables, for voice communication system at local workstations in 25mm dia PVC conduits/already installed cable trays as shown in the layout plan and schematic diagrams. Work includes all terminations, management and tagging at both ends.

2,000 Rft

INFORMATION OUTLETS

G3 Workstation wall mounted Information outlet having Duplex Face plate with 1No. CAT-6 RJ-45 socket for data communication system including shuttered click-ins, labels, jacks etc. Complete in all respects with cable identification tags.

24 No.


Page 15 of 20

G4 Workstation wall mounted Information outlet having Duplex Face plate with 1No. CAT-6 RJ-45 socket for voice communication system including shuttered click-ins, labels, jacks etc. Complete in all respects with cable identification tags.

4 No.

COMMUNICATION RACKS

G5 Supply, installation and connecting-up of imported 9U, 19" wall mounted rack complete with perforated front and back door panels as required and with all accessories including back boards, frame, cable management troughs, labels, label holder, cable guide etc. with lockable doors, of size sufficient to accommodate 19" rack mountable servers, patch panels & active networking equipments. The cabinet includes vertical fingure cable manager; air duct.The rack must have internal independent grounding system which could be plugged with the main grounding system of the data center. .

1 No.

PATCH PANELS & CABLE MANANGEMENT

G6 24 Port , 19 inch Patch Panel for data communication, Straight, Flush Mount, 1 RU equipped with 24 Nos. Cat-6 Unshielded RJ45 information outlet including labeling complete in all respect.

1 No.

G7 24 Port , 19 inch Patch Panel for voice communication, Straight, Flush Mount, 1 RU equipped with 24 Nos. Cat-6 Unshielded RJ45 information outlet including labeling complete in all respect.

1 No.

G8 Front & Rear Cable Management for above patch panels. 2 No.

MDF & TELEPHONE JUNCTION BOXES

G9 MAIN DISTRIBUTION FRAME MDF (Main Distribution Frame) for termination of PTCL Trunk Lines made with 16SWG powder coated MS sheet, weather proof housing having 100 pair fused links including surge protectors for each pair.

1 No.

G10 TJB (TELEPHONE JUNCTION BOXES) Following Telephone Junction Boxes (TJBs) made with 16 SWG Sheet Steel Housing powder coated having connecting strips for horizontal voice cabling.

a 50 Pair 1 No.

PATCH CORDS

Category-6 Factory Certified tangle free RJ-45 to RJ-45 type patch / drop cords in required colors having following lengths for interconnection of switches and patch panels.

G11 1 meter long patch cords for data 24 No.

G12 3 meter long drop cord for data 24 No.

PATCH CORDS VOICE


Page 16 of 20

Supply, Installation and connecting-up patch cords of Cat-6 UTP, 4-Pair (RJ-45 to 110 Connector molded type plugs) factory certified (in required color). from patch panel to Rack Mounted Tag Blocks for voice communication system

G13 1 meter long patch cords for voice 4 No.

BACKBONE CABLING VOICE COMMUNICATION

Following multipair, 0.6 mm Armored Cat-3/Cat-5 Telephone Cable for connectivity of TJB/MDF/Com Racks in appropriate size of UPVC Class D Conduit including excavation, back filling and compaction as per details given in the drawings including tagging, termination, testing and commissioning at both ends.

G14 10 Pair 300 Rft

TESTING & COMMISSIONING

G15 Comprehensive Testing and commissioning Report of complete structured cabling system including written warranties from the Principal Manufacturer. (3 Copies)

1 Job

SECTION - H

GROUNDING & BONDING

Providing , installation , testing and commissioning of following items for earthing & bonding system of complete data center including all material, boring, labor, tools, transportation, accessories etc. Complete in all respects including detailed test reports.

EARTH STATIONS

H1 Providing fixing and connecting of earthing set which consist of one copper rod of size 20mm dia 3 meters long buried at 20 meter below the ground level buried at least 3 meter away from the nearest foundation the earth lead shall be of 2 Nos.70mm2 stranded copper conductor drawn in 50mm dia G.I pipe from the earthing rod to the panels transformer earth pit including Boring / digging as required and refilling the earth pits with necessary lime powder wooden cool as requires and approved electrical inspector IEE regulation and confirming to the Specification including make of earth pit with cast iron manhole cover 150mm x 150mm.

2 No.

EARTH CONNECTING POINTS

H2 Earth Connecting Point 300 mm x 50 mm x 5 mm electroplated Copper bar , as shown in drawings. Bar shall be provided with holes suitable for installation of required earth leads. The test bar shall be enclosed in powder coated metal enclosure as approved by the client.

2 No.

EARTH LEADS / CONDUCTORS


Page 17 of 20

Following green pvc insulated / bare copper, earthing conductors/leads for earth stations and equipment grounding in appropriate size of UPVC conduit as shown in the drawings.

H3 1C, 70 Sqmm PVC Insulated Copper Conductor 300 Rft

SECTION - I

UNINTRUPTIBLE POWER SUPPLY (UPS)

I1 Microprocessor based On Line Double Conversion, True Sinusoidal 6 KVA UPS, in free standing tower casing including maintenance free dry batteries suitable for 60 minutes back up at full load. The UPS shall be single phase in and single phase out. The UPS should have built in automatic by pass switch, LCD Display, event logging memory, LED Alarms. Complete in all respects with all protection devices. (APC MAKE / MG MAKE)

1 No.

SECTION - J

IP CCTV SECURITY SURVEILLANCE SYSTEM

Supply, Installation, testing and commissioning of following items for IP based CCTV System including but not limited to the description given here under including all power and communication accessories, housings, mounting brackets, suspension rods etc. required for completion of the system.

CCTV WALL CAMERA (TYPE-A)

J1 Surface mounted, 3.5-8 mm Varifocal lens Dome type PoE I.P Camera with day and night feature having resolution 1280x960 pixels with live and recording quality of 10 fps, along with all mounting accessories complete in all respects.

8 No.

CCTV WALL CAMERA (TYPE-B)

J2 Wall bracket, 2.8-10 mm Varifocal lens Box type PoE I.P Camera with day and night feature having resolution 1280x960 pixels with live and recording quality of 10 fps, along with all mounting accessories complete in all respects.

8 No.

NETWORK POE SWITCH

J3 16 Port 100 Mbps PoE Network Switch 1 No.

NETWORK VIDEO RECORDER

J4 Network Video Recorder, NVR with 16-channels Video input. The NVR shall be equipped with LAN / WAN facility. NVRs should have minimum 30 days storage capacity, RW CD Drive. Complete with all connecting cords and accessories using CMS Software.

1 No.

CCTV WIRING

J5 Wiring for CCTV System using CAT-6 cables in 25 mm dia Fire Rated conduit from NVR to Network Switch and from Network switch to all Cameras as shown in the schematic diagram. Complete in all respects.

16 No.

TESTING, COMMISSIONING & TRAINING


Page 18 of 20

J6 Programming, testing and commissioning of whole system as per the client requirement including training of client's representatives. Complete set of all manual shall be provide at the time of commissioning.

1 Job

SECTION - K

PUBLIC ADDRESS SYSTEM

Supply & installation of following items for Public Address Control System as per details provided in the Specifications and Drawings including all accessories. Complete in all respects.

AMPLIFIERS

K1 Providing & Installation of 120W Mixer / Power Amplifier / 6 Microphone and 2 Aux input 220V Acer Version, Complete System.

1 No.

CEILING SPEAKERS

K2 Recessed Ceiling Speakers for public address system, 6W with tappings and matching 100V transformer, powder coated metal grill. The speaker shall be provided with a protective steel fire dome. Complete with all accessories.

8 No.

WALL / COLUMN SPEAKERS

K3 12 W Bracket mounting column speaker intended for high quality speech reproduction with sealed enclosure protective against moisture and dust. The speaker shall have output power adjustments for full, half and quarter power outputs.

2 No.

LOCAL CALL STATIONS

K4 2 Zone Call Station for local announcement / in department announcement. The Call Station shall have metal base, a flexible microphone stem with microphone and zone selection and LED Indication Lights for standby by, active and priority indications.

1 No.

MICROPHONE OUTLETS

K5 Micro phone outlet including 16 SWG sheet steel back box. 2 No.

TESTING AND COMMISSIONING

K6 Programming , testing and commissioning of the complete system as per the system specifications and instructions of consultant/architect.

1 Job

SECTION - L

CONVENTIONAL FIRE ALARM DETECTION SYSTEM

Providing, installation, testing and commissioning of following items for complete Addressable Intelligent fire alarm system including smoke detectors, call stations, sounders etc. complete in all respects.

WIRING FOR FIRE ALARM SYSTEM


Page 19 of 20

L1 Wiring for Addressable Fire Alarm System using 2C, 1.5 Sqmm shielded fire rated cables in 25mm dia pvc conduit from FACP to each devices in looping arrangement as shown in the layout plan. Complete will all conduit accessories, saddles, junction boxes, bends etc.

26 No.

CONVENTIONAL FIRE ALARM CONTROL PANEL

L2 Fire Alarm Control Panel flush in wall, 4 Zone Conventional suitable to support minimum 30 devices per zone. The panel shall be equipped with built in maintenance free sealed batteries having minimum 3 hours back up. The panel should be able to configure at site without additional hardware and capable to support excess sounders as per schematic diagram via additional power modules has to be part of FACP. If required for fire alarm sounder Complete will all mounting accessories as described in the specifications.

1 No.

PHOTOELECTRIC SMOKE DETECTORS

L3 Conventional Optical Smoke Detectors including base having built in short circuit isolator, incorporating a pulsing LED located in labyrinth with in the housing of the detector. Sensing of the detector shall be adjustable via software.

20 No.

HEAT DETECTOR

L4 Conventional Optical Rate of Rise Heat Detectors including base having built in short circuit isolator, incorporating a pulsing LED located in labyrinth with in the housing of the detector. Sensing of the detector shall be adjustable via software.

2 No.

MANUAL CALL STATION

L5 Conventional Break Glass type Manual Call Station having a built in short circuit isolator & built in micro processor to ensure a response time of max. 1 sec. It also incorporates an indication LED fleshed after pressing the button to acknowledge the activation & key operation facility for testing purposes.

2 No.

SOUNDER WITH FLASHER

L6 Conventional electronic sounder with flasher, minimum sound output 90-100 db at 1meter with frequencies for variety of sounds as required. Sounder shall have built in short circuit isolator, configured via software.

2 No.

TESTING, COMMISSIONING & TRAINING

L7 Testing, commissioning and training of Fire Alarm and Detection System in presence of consultant and client including submission of certified test report. Item includes comprehensive training of end user for safe operation and support.

1 Job

SECTION - M

AIR CONDITIONING SYSTEM


Page 20 of 20

M1 Supply and Installation of VRF Units, including testing and commissioning of refridgerant piping complete. Gree / Haier / Media

a 2 x 25 Ton VRF Units (Rate Quoted Per Ton) 50 ton

SECTION - N

BED HEAD UNITS

BED HEAD UNIT TYPE-D (CONTINUOUS)

N1 Patient Bed Head Unit (continuous wall mounted) having isolated channel / rail for medical gas supplies and electrical services. Each Bed shall have up and down lights (28W), On Off Switch with cord, 4No. Medical Gas Outlets, 4x13A Multipin sockets outlets (13/15A), equipotential earth stud etc. Complete with all mounting accessories as approved by architect and consultant.

20 No.

N2 Emergency Gas Stopping Valves. 1 No.

N3 Gas Pressure Meter. 1 No.

N4 Supply, Installation, Testing and Commissioning of gas outlets copper piping make Muller, complete in all respect.

2000 Rft.

END

Documents

A - Interior Design Works - UNHCR PAKISTAN · A - Interior Design Works S.NO. DESCRIPTION OF ITEM QTY. UNIT 1 Demolition & Dismantling a) Block Masonry Walls Demolition of highlighted