GETTING IT LOUD

To get oriented, put your RMS meter on the track you want to want yours to sound like (more or less). Listen to a full, loud portion of the song and take a look at the Average RMS:

Now, put the meter on your own song and take a reading. Let's say the unmastered song shows an average RMS of -19. That would mean we have an approximately 10dB defecit to make up. Just for laughs, let's dive right in and make up the gain using Limiter:

You can use the meter to fine tune this, but don't spend too long with that. Switch over to using your ears. A/B the tracks and give a good listen. The loudness is probably in the ballpark now.Pay close attention and you may find that even matching the RMS level very closely, your mix still doesn't sound as loud. This may be because the track you're comparing yours to is exceptionally well mixed, or has been mastered by a professional who has other tricks for maximizing the apparent loudness.

EQ: CHECK THE GAIN

A simple but useful feature of Live's EQ 8 is the Gain control:

It's just a simple volume control, but it comes in handy for A/B-ing your EQ setups. If you're making an EQ adjustment that raises or lowers the volume of a signal noticeably, you can cut or boost the gain a return the signal to the volume it was at before you applied the EQ. If you're not familiar with this process, give it a try. After making your EQ settings, turn off the EQ completely...

...and listen for a gain change. Take a guess at how much you need to adjust the Gain control, then turn the EQ on and off again. Repeat until you the volume sounds the same whether or not the EQ is on. Now you can A/B the signal with and without the EQ while listening to the entire mix and get a real sense of what the EQ is (or isn't doing).

BEAT REPEAT: THE SILENCER

I'm working on a new glitcher/beat masher for my upcoming gigs, and I had the idea to flip the Beat Repeat on its head. What if, instead of having it generate tons of repeated hits, I used it to generate lots of silence. Check it out:

Decay is set to 100%. This means that the repeats fade out to silence almost instantly.Output Mode is set to Ins which means that every time repeats are triggered the original signal is cut out.Gate is set to 6/16 which is longer than the time it takes Decay to fade the repeated signal to silence. When you add these three parameters together, you get a Beat Repeat that triggers silence instead of repeats!Interval and Grid are important here as well. With Interval at 1/8, there's a Chance (77.8% in this case) that silence will occur every 1/8th note of the bar. Grid is set to 1/16 which is slow enough that Decay fades the repeats to silence before you hear them. Try Grid at a faster setting (like 1/96) and you'll hear a buzzing as the repeats fade away.How is this useful? We'll get into that in the next tip.

RACK OF REPEATS

So, now that you've checked out how to make a Beat Repeat insert silence into a sound, what to do with it? Well, what I'm experimenting with is layering and offsetting several Beat Repeats set up in this fashion. Use the Group command to put the Beat Repeat into a Rack, then Duplicate the Chain a couple of times.

Now you'll have three chains all doing roughly the same thing, but not quite - each has a bit of randomness to it.Into the second chain, insert a few effects:

The most important part of this chain is the Simple Delay at the beginning. It's set to 100% Wet and has its Feedback set to zero, so all it's doing is offsetting the second chain by 3/16ths. The Redux is helping to differentiate the sound from the first chain, while the Auto Filter is removing most of the Kick drum (I've been using it primarily on drum loops).Now add effects to the third chain. Again, use a Simple Delay to offset this chain to a different value, and use different processors to differentiate the sound in a another way. Things should start to sound pretty nuts by now.In the next tip, we'll get into adding performance controls.

SLOPPY CLAPS

Since we've been discussing some issues related to Simpler and velocity, I thought I'd show you a rack I made for a remix I'm working on. There's a section of this track where we need a really loose sounding hand clap section. At the moment, it's not practical for me to get a room full of people clapping along, so I've figured out a

way to get a similar result with an Instrument Rack.The first step is to drag a bunch of samples into an empty Instrument Rack, so you get something that looks like this:

Notice that I've panned the samples a bit, and used a few snaps as well for variety. Also, some of the clap samples have a little space at the beginning:

That's a good thing - it adds to the sloppiness. Next, I'll do a little trickery with the velocity. I'm gonna give each of the samples a different velocity sensitivity (30%, 40%, 50%, etc.):

Now, depending on how hard the key or drum pad is hit, different samples will respond differently, making the volume balance of the samples a little different for each hit.This gets us off to a good start, but there are still a few more tricks for adding realism that we'll get into tomorrow.

DUPE THAT LOOP

Since I've been talking about the MIDI editor for the last two days, I'm going to take this opportunity to answer a question that a reader asked about the best way to duplicate loops during MIDI editing.When programming parts, it's very common to start with a 1 bar loop to get the basic feel, then duplicate that loop out to two, four or eight bars to create some

variations. There are lots of ways to get this done - I'll show you mine. It's nice and quick, and requires very little use of the mouse.Once you've got your one bar loop programmed, click on the Loop Brace. This will turn it's horizontal bar solid black, and highlight the entire bar in yellow as seen below.

Now it's time to duplicate the loop, which we'll do using the Duplicate Time command (cmd+shift+D on the Mac). We could just as easily use Duplicate, but that would move the loop. Duplicate Time leaves the loop position alone. To make the pattern four bars long, you would use Duplicate Time three times. Zoom all the way out, and you'll have something that looks like this:

The final step is to extend the loop length to four bars. Cmd+up arrow (Mac) or Ctrl+up arrow (PC) doubles the length of the loop, so double the length of the loop twice and you're there. Remember that the loop has to be selected (as shown above) for this command to work. That's it! Now you've created a nice four bar loop with a minimum of fuss, and you're ready to start programming variations.

A LITTLE BUZZED

Here's a simple trick to get a little glitch into your sampled drums. Set up Simpler like this:

What you're seeing here is a snare hit with a short loop at the end. Instead of having a natural decay, the hit will buzz at the end.First, make sure that the Loop switch is turned on.Length specifies the end point of the loop while Loop is used to dial in where the looping begins.Whether or not you hear the loop depends on the length of the midi note that triggers it.

So, in this example the first note will produce a straight snare hit, because the note cuts off before the loop begins. The second sustains longer so you'll hear the buzzing towards the end.

A LITTLE MORE BUZZED

The interesting thing about setting loops in Simpler is that the Loop parameter is specified as a percentage of the sample's Length. In other words, if Loop is set to 20%, you'll always be looping the last 20% of the sample regardless of what Length is set to. This means that adjusting Length adjusts both the loop's start and end points and changes the length of the loop. (Try it).What this also means is that you can get some very interesting and strange results by automating the length parameter.

Above you'll see that I've created a clip envelope for the Length parameter, which is going to cause all sorts of different loop positions and times.

I've also Unlinked the envelope which means that the envelope's length is now independent of the length of the MIDI clip. The Length of the envelope is set to an odd value (1.0.1) which means that its position will shift relative to the MIDI clip over many bars, producing a wide variety of results.

PRODUCING FOR THE GIG

Lately, I've been doing a fair amount of "speed production" while on the road. This just means producing tracks with only my live set in mind. Rather than try to create something that develops over 4-7 minutes and is ready to release, I'll create material that works really well for two minutes during a performance.I typically would do this in a separate Set, export a stereo file, then bring it into the performance Set. But lately I've found a better way: work directly in the performance set. The advantage here is that I can listen to other material in my set while developing the new beat. This is really helpful because it allows me to hear how everything will mix together. The trick to keeping this manageable is to use Group tracks:

The tracks at the far left are two Group tracks containing two different production sessions. My normal performance set begins with the track named "1 - Tracks".The advantage here is that you can unfold the group to work on the new beat...

...or fold it to treat the scenes as if they were clips. The group track also serves as a master channel so you can listen with some limiting to get it up to the volume of finished songs.Once you've got your basic material for the new track together, just grab the group track and drag it into the browser to save the new song as its own Set.

Now the group can be deleted from your performance set.There's lots more details to discuss regarding this process...more tips to follow...

LISTEN TO THE STEREO STUFF

As I've mentioned in prior tips, the Utility device can be used to remove all of the mono information from a signal so you can hear the purely stereo information. Just set Width to 200%:

Something I like to do is listen to my reference tracks at 200% just to get a sense of how "wide" they are, or more specifically how much panning and stereo effects are in the mix for a particular track.Just like it's important to contrast sounds that are bright and dark, etc. it's also important to know how to contrast pure mono sounds with panned sounds and sounds that use stereo effects to create width. However, it's also instructive to notice that some great sounding tracks are almost completely mono! All you hear at 200% is a little bit of reverb...Pay close attention to what you hear. Hihats? Snare? Sound FX? Reverb? Bet you don't hear any kick or serious low frequencies of any sort. (let's keep those mono, people!) If you need to get a little more stereo width into your life, make sure to explore Simple Delay, Grain Delay, reverb, chorus, auto filter (with the LFO), flanger, phaser, etc...