Embed Size (px)
Citation preview
Contact Details Registration No. HOKLAS 104 Page 1 of 1
104 TEST CAL
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司 ADDRESS 地址
:
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街15-33葵德工業中心第二座二字樓F
ENQUIRY 查詢
: Mr Terrence KWOK Cheuk-lun, Quality Manager 郭卓麟先生，品質管理經理
TELEPHONE 電話
: 2422 6898
FAX 傳真
: 2419 1137
E-MAIL 電郵
CLIENTELE 服務對象
: Public 公眾
Last updated on: 16 May 2016
Scope of Accreditation Registration No. HOKLAS 104 Page 1 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
ADDRESS 地址
Main laboratory : Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street,
Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Test location : Flat 9, G/F, Golden Industrial Building, 16-26 Kwai Tak Street, Kwai Chung,
New Territories, Hong Kong 香港新界葵涌葵德街 16-26 金德工業大厦地下 9 號
ACCREDITED TEST CATEGORY 認可測試類別
: Calibration Services 校正服務 Construction Materials 建築材料
Scope of Accreditation Registration No. HOKLAS 104 Page 2 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat 9, G/F, Golden Industrial Building, 16-26 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 16-26 金德工業大厦地下 9 號
Calibration Services 校正服務
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED@ 特定測試或量度的特性@
CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* 校準和測量能力*
Construction materials testing equipment - Welding gauge used for Calibration in accordance with measuring the dimension in-house method OP-55 of joint before and after for the following parameters : welding Scale measuring bevel angle 1º Scale measuring fixed bevel angle 1º Ruler 0.2 mm Scale measuring gap width 0.06 mm Scale measuring weld width 0.2 mm Scale measuring high low, weld cap and leg 0.5 mm length Scale measuring undercut depth 0.5 mm Scale measuring weld throat 0.5 mm - Welding gauge calibrator Calibration in accordance with set in-house method OP-54 for the following parameters : Step wedge 20 µm Angle wedge 0.2o @
UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.
* THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION.
Scope of Accreditation Registration No. HOKLAS 104 Page 3 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat 9, G/F, Golden Industrial Building, 16-26 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 16-26 金德工業大厦地下 9 號
Calibration Services 校正服務
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED@ 特定測試或量度的特性@
CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* 校準和測量能力*
Length measurements - Dial calipers Calibration in accordance with - Digital calipers in-house method OP-27 over the following range : Up to 330 mm 10 µm - Vernier calipers Calibration in accordance with Cl. B1 of BS 887: 1982 over the following range : Up to 330 mm 31 µm - Coating thickness gauge Calibration in accordance with in-house method OP-75 over the following ranges : Up to 1434.4 μm 0.3 μm to 7.4 μm - Dial gauge Calibration using micrometer head in accordance with Cl. B3 of BS 907: 1965 or Cl. A5 of AS 2103: 1978 over the following range : Up to 50 mm 3.2 µm Calibration using micrometer head and gauge block in accordance with in-house method OP-19 over the following range : Up to 100 mm 3.2 µm @
UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.
* THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION.
Scope of Accreditation Registration No. HOKLAS 104 Page 4 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat 9, G/F, Golden Industrial Building, 16-26 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 16-26 金德工業大厦地下 9 號
Calibration Services 校正服務
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED@ 特定測試或量度的特性@
CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* 校準和測量能力*
Length measurements (cont’d) - Displacement Calibration using micrometer head and gauge measuring device block in accordance with in-house method OP-84 over the following range : Up to 100 mm 3.2 µm - External micrometer Calibration in accordance with App. A of BS 870: 1950 over the following range : Up to 25 mm 2 µm - Extensometer On-site calibration in accordance with BS 3846: 1970 using calibration rig for the following : Grade B for gauge length 100 mm to 200 mm 0.8 μm Grade C for gauge length 10 mm to 200 mm 0.8 μm Grade D for gauge length up to 200 mm 0.8 μm On-site calibration in accordance with BS EN 10002-4: 1995, ISO 9513: 1999 or ISO 9513: 2012 using calibration rig for the following : Class 1 for gauge length 0.8 μm Up to 200 mm On-site calibration in accordance with ASTM E83: 2002 using calibration rig for the following : Class B-1, B-2, C, D and E for gauge length 0.8 μm Up to 200 mm @
UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.
* THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION.
Scope of Accreditation Registration No. HOKLAS 104 Page 5 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat 9, G/F, Golden Industrial Building, 16-26 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 16-26 金德工業大厦地下 9 號
Calibration Services 校正服務
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED@ 特定測試或量度的特性@
CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* 校準和測量能力*
Mass and related measurements - Balance Calibration in accordance with in-house method OP-69 over the following range : Up to 6 kg 0.42 mg to 6.54 mg Above 6 kg to 70 kg 0.008 g to 0.074 g (Calibration is conducted using OIML Class F1 weights from 1 mg to 70 kg) On-site calibration in accordance with in-house method OP-69 over the following range : Up to 6 kg 0.005 mg to 6.54 mg Above 6 kg to 70 kg 0.008 g to 0.074 g (Calibration is conducted using OIML Class F1 weights from 1 mg to 70 kg) - Force measurements - Force measuring device Calibration in accordance with for pile test in-house method OP-18 - load cell over the following ranges : - load cell with hydraulic jack from 300 kN to 16000 kN 0.6 % of reading - Force measuring Calibration in accordance with instrument in in-house method OP-17 compression mode over the following range : from 1 kN to 1500 kN 0.5 % of reading @
UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.
* THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION.
Scope of Accreditation Registration No. HOKLAS 104 Page 6 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat 9, G/F, Golden Industrial Building, 16-26 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 16-26 金德工業大厦地下 9 號
Calibration Services 校正服務
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED@ 特定測試或量度的特性@
CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* 校準和測量能力*
Mass and related measurements (cont'd) - Force measurements (cont'd) - Universal testing machine On-site calibration using true force method or 0.3 % in compression mode indicated force method in accordance with (Calibration is conducted using Grade 1.0 load cell) BS 1610: Part 1: 1992 over the following range : 0.4 kN to 3000 kN On-site calibration using true force method or 0.3 % indicated force method in accordance with (Calibration is conducted using Class 1 load cell) BS EN ISO 7500-1: 1999 or BS EN ISO 7500-1: 2004 over the following range : 0.4 kN to 3000 kN On-site calibration using 0.3% follow-the-force method (Calibration is conducted using elastic calibration or set-the-force method devices) in accordance with ASTM E4: 2002 over the following range : 0.4 kN to 3000 kN @
UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.
* THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION.
Scope of Accreditation Registration No. HOKLAS 104 Page 7 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat 9, G/F, Golden Industrial Building, 16-26 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 16-26 金德工業大厦地下 9 號
Calibration Services 校正服務
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED@ 特定測試或量度的特性@
CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* 校準和測量能力*
Mass and related measurements (cont'd) - Force measurements (cont'd) - Charpy V-notch Impact On-site indirect verification tester in accordance with BS EN 10045-2: 1993 (Cl. 6) or BS EN ISO 148-2: 2008 over the following two absorbed energy levels : Up to 40 J 1.6 J Above 40 J to 300 J 5.7 J - Hardness measurements - Hardness testing machine On-site indirect verification for measuring Vickers hardness in accordance with BS EN ISO 6507-2: 1998 or BS EN ISO 6507-2: 2005 over the following hardness ranges : Up to 225 HV 5 1.6 % 400 HV 5 to 600 HV 5 1.3 % 700 HV 5 to 1000 HV 5 1.2 % Up to 225 HV 10 1.5 % 400 HV 10 to 600 HV 10 1.4 % 700 HV 10 to 1000 HV 10 1.3 % Up to 225 HV 30 1.2 % 400 HV 30 to 600 HV 30 1.2 % 700 HV 30 to 1000 HV 30 1.3 % On-site indirect verification for measuring Rockwell hardness in accordance with BS EN ISO 6508-2: 1999 over the following hardness ranges : 20 HRC to 30 HRC 1.1 HRC 35 HRC to 55 HRC 1.1 HRC 60 HRC to 70 HRC 1.1 HRC @
UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.
* THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION.
Scope of Accreditation Registration No. HOKLAS 104 Page 8 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat 9, G/F, Golden Industrial Building, 16-26 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 16-26 金德工業大厦地下 9 號
Calibration Services 校正服務
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED@ 特定測試或量度的特性@
CALIBRATION AND MEASUREMENT CAPABILITY (CMC)* 校準和測量能力*
Mass and related measurements (cont’d) - Pressure measurements - Hydraulic pressure Calibration in accordance with indicating instrument in-house method OP-1 and gauge using deadweight tester over the following ranges :- from 0.2 bar to 10 bar 0.01 bar from 10 bar to 1100 bar 0.03 % of reading Calibration in accordance with with in-house method OP-1 using digital pressure calibrator over the following ranges : Up to 206 bar (water as pressure medium) 0.2 % of reading Up to 700 bar (mineral oil as pressure 0.1 bar or 0.2 % of reading, whichever is the greater medium) - Gas pressure indicating Calibration in accordance with instrument and gauge in-house method OP-1 over the following ranges : from -1 bar to 2.5 bar 0.1 % of reading from 2.5 bar to 20 bar 0.3 % of reading - Torque measurements - Manually operated Calibration in accordance with torque wrench BS EN 26789: 1994, ISO 6789: 1992 or in-house method OP-2 over the following ranges : from 1 Nm to 20 Nm 0.24 Nm from 20 Nm to 100 Nm 1 % of reading from 100 Nm to 1000 Nm 0.58 % of reading @
UNLESS OTHERWISE SPECIFIED, ACCREDITED ACTIVITIES ARE CONDUCTED AT THE LABORATORY.
* THE CALIBRATION UNCERTAINTY OF A DEVICE UNDER TEST IS USUALLY REPORTED AT 95% CONFIDENCE LEVEL AND DEPENDS ON BOTH THE CMC OF THE LABORATORY AND THE PERFORMANCE OF THE DEVICE DURING CALIBRATION.
Scope of Accreditation Registration No. HOKLAS 104 Page 9 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Curtain walls & cladding Proof load test of spiders & glass fixing Code of Practice for the Structural Use of Steel (2005) (fixing components) components in the force range Cl. 16.2 up to the force of 1000 kN Code of Practice for the Structural Use of Steel (2011) Cl. 16.2 In-house method OP-70 Metallic materials Bend test of metallic materials BS 1639: 1964 BS EN ISO 7438: 2000 Charpy V-notch impact test of metallic BS EN 10045-1: 1990 materials BS EN ISO 148-1: 2010 ISO 148-1: 2009 BS EN 10045-1: 1990 or BS EN ISO 148-1: 2010 in conjunction with the following specification(s): BS EN 10021: 2006 Cl. 8.3.4.1 BS EN 10025-1: 2004 Cl. 10.2.2 BS EN 10025-2: 2004 Cl. 10.2 BS EN 10025-3: 2004 Cl. 10.2 BS EN 10025-4: 2004 Cl. 10.2 BS EN 10025-5: 2004 Cl. 10.2 BS EN 10025-6: 2004 + A1: 2009 Cl. 10.2 BS EN 10210-1: 2006 Cl. 9.2.3 Hardness test of metallic materials – BS 427: 1990 Vickers hardness test – HV5, HV10 and BS EN 23878: 1993 HV30 BS EN ISO 6507-1: 1998 BS EN ISO 6507-1: 2005
Scope of Accreditation Registration No. HOKLAS 104 Page 10 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Metallic materials Breaking force test of steel wire ropes BS EN 12385-1: 2002 +A1: 2008 Cl. 6.4.1 (cont’d) in the force range of 0.4 kN to 1500 kN BS EN 12385-1: 2002 +A1: 2008 Cl. 6.4.1 with modifications in conjunction with the following specification(s): BS EN 12385-4: 2002 + A1: 2008 BS EN 12385-5: 2002 BS EN 12385-6: 2004 BS EN 12385-7: 2002 BS EN 12385-8: 2002 BS EN 12385-9: 2002 BS EN 12385-10: 2003 + A1: 2008 Tensile test of metallic materials in the force BS 18: 1987 range of 0.4 kN to 1500 kN BS EN 10002-1: 2001 ASTM E8M-01 BS EN ISO 6892-1: 2009 ISO 6892-1: 2009 BS 18: 1987 in conjunction with the following specification(s): BS 4360: 1990 Cl. 23 BS EN 10002-1: 2001 or BS EN ISO 6892-1: 2009 in conjunction with the following specification(s): BS EN 10021: 2006 Cl. 8.3.4.1 BS EN 10025: 1990 Cl. 8.7.2.1 BS EN 10025-1: 2004 Cl. 10.2.1 BS EN 10025-2: 2004 Cl. 10.2 BS EN 10025-3: 2004 Cl. 10.2 BS EN 10025-4: 2004 Cl. 10.2 BS EN 10025-5: 2004 Cl. 10.2 BS EN 10025-6: 2004 + A1: 2009 Cl. 10.2 BS EN 10113-1: 1993 Cl. 8.6.2.1 BS EN 10113-2: 1993 Cl. 8.6 BS EN 10113-3: 1993 Cl. 8.6 BS EN 10137-1: 1996 Cl. 8.6.2.1 BS EN 10137-2: 1996 Cl. 8.6 BS EN 10137-3: 1996 Cl. 8.6 BS EN 10155: 1993 Cl. 8.7.2.1 BS EN 10210-1: 2006 Cl. 9.2.2
Scope of Accreditation Registration No. HOKLAS 104 Page 11 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Metallic materials Charpy V-notch impact test of fasteners BS EN 10045-1: 1990 or BS EN ISO 148-1: 2010 (cont’d) in conjunction with the following specification(s): BS EN 14399-1: 2005 Cl. 5.3 BS EN 14399-1: 2015 Cl. 5.3 BS EN 14399-3: 2005 Cl. 3.2 BS EN 14399-3: 2015 Cl. 3.2 BS EN 14399-4: 2005 Cl. 3.2 BS EN 14399-4: 2015 Cl. 3.2 BS EN 14399-7: 2007 + A1: 2010 Cl. 4.3 BS EN 14399-8: 2007 + A1: 2010 Cl. 4.3 BS EN 14399-10: 2009 Cl. 4.2 BS EN 15048-1: 2007 Cl. 5.3 BS EN ISO 148-1: 2010 in conjunction with the following specification(s): BS EN ISO 898-1: 2009 Cl. 9.14 BS EN ISO 898-1: 2013 Cl. 9.14 Proof load test of fasteners in the force range BS EN ISO 898-1: 1999 Cl. 8.5 of 0.4 kN to 1500 kN BS EN ISO 898-1: 2009 Cl. 9.6 BS EN ISO 898-1: 2013 Cl. 9.6 BS EN ISO 898-1: 1999 in conjunction with the following specification(s): BS 3692: 2001 Cl. 19.2 BS 3692: 2014 Cl. 21 BS 4190: 2001 Cl. 15.2 BS 4190: 2014 Cl. 15.2 BS EN 14399-1: 2005 Cl. 5.3 BS EN 14399-1: 2015 Cl. 5.3 BS EN 14399-3: 2005 Cl. 3.2 BS EN 14399-3: 2015 Cl. 3.2 BS EN 14399-4: 2005 Cl. 3.2 BS EN 14399-4: 2015 Cl. 3.2 BS EN 14399-7: 2007 + A1: 2010 Cl. 4.3 BS EN 14399-8: 2007 + A1: 2010 Cl. 4.3 BS EN 14399-10: 2009 Cl. 4.2 BS EN 15048-1: 2007 Cl. 5.3
Scope of Accreditation Registration No. HOKLAS 104 Page 12 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Metallic materials Tensile test of fasteners in the force range of BS EN 10002-1: 2001 (cont’d) 0.4 kN to 1500 kN in conjunction with the following specification(s): BS EN ISO 898-1: 1999 Cl. 8.1 & 8.2 BS EN ISO 3506-1: 1998 Cl. 6.2.2, 6.2.3 & 6.2.4 BS EN ISO 6892-1: 2009 in conjunction with the following specification(s): BS EN ISO 898-1: 2009 Cl. 9.2, 9.3, 9.4, 9.5 & 9.7 BS EN ISO 898-1: 2013 Cl. 9.2, 9.3, 9.4, 9.5 & 9.7 BS EN ISO 3506-1: 2009 Cl. 7.2 BS EN ISO 898-1: 1999, BS EN 10002-1: 2001 in conjunction with the following specification(s): BS 3692: 2001 Cl. 19.2 BS 3692: 2014 Cl. 21 BS 4190: 2001 Cl. 15.2 BS 4190: 2014 Cl. 15.2 BS EN 14399-1: 2005 Cl. 5.3 BS EN 14399-1: 2015 Cl. 5.3 BS EN 14399-3: 2005 Cl. 3.2 BS EN 14399-3: 2015 Cl. 3.2 BS EN 14399-4: 2005 Cl. 3.2 BS EN 14399-4: 2015 Cl. 3.2 BS EN 14399-7: 2007 + A1: 2010 Cl. 4.3 BS EN 14399-8: 2007 + A1: 2010 Cl. 4.3 BS EN 14399-10: 2009 Cl. 4.2 BS EN 15048-1: 2007 Cl. 5.3 Tensile test of fasteners in the force range of BS EN ISO 3506-1: 1998, BS EN 10002-1: 2001 0.4 kN to 1500 kN in conjunction with the following specification(s): BS EN 15048-1: 2007 Cl. 5.3 Tensile test of fastener/nut assemblies in the BS EN ISO 15048-2: 2007 Cl. 5 force range of 0.4 kN to 1500 kN
Scope of Accreditation Registration No. HOKLAS 104 Page 13 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Metallic materials Proof load test of nuts in the force range of BS 3692: 2001 Annex C.1 (cont’d) 0.4 kN to 1500 kN BS 3692: 2014 Annex C.1 BS 4190: 2001 Annex A.1 BS 4190: 2014 Annex A.1 BS EN 20898-2: 1994 Cl. 8.1 BS EN ISO 898-2: 2012 Cl. 9.1 BS EN ISO 898-6: 1996 Cl. 8.1 BS EN 20898-2: 1994 in conjunction with the following specification(s): BS EN 14399-1: 2005 Cl. 5.3 BS EN 14399-1: 2015 Cl. 5.3 BS EN 14399-3: 2005 Cl. 4.2 BS EN 14399-3: 2015 Cl. 4.2 BS EN 14399-4: 2005 Cl. 4.2 BS EN 14399-4: 2015 Cl. 4.2 BS EN 14399-7: 2007 + A1: 2010 Cl. 5.2 BS EN 14399-8: 2007 + A1: 2010 Cl. 5.2 BS EN 14399-10: 2009 Cl. 5.2 BS EN 15048-1: 2007 Cl. 5.3 BS EN 20898-2: 1994, BS EN ISO 898-6: 1996 in conjunction with the following specification(s): BS EN ISO 3506-2: 1998 Cl. 6.2 BS EN ISO 898-2: 2012 in conjunction with the following specification(s): BS EN ISO 3506-2: 2009 Cl. 7.2 BS EN ISO 3506-2: 1998 in conjunction with the following specification(s): BS EN 15048-1: 2007 Cl. 5.3
Scope of Accreditation Registration No. HOKLAS 104 Page 14 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Metallic materials Ultrasonic test of metallic materials BS 5996: 1993 (non-destructive) BS EN 10160: 1999 Metallic materials & Ultrasonic thickness measurement of BS EN 14127: 2004 non-metallic materials metallic materials and non-metallic (non-destructive) materials Structural fixings Proof load test of anchor bolts, cast-in fixings BS 5080-1: 1993 Cl. 7.1.1 & 7.1.3 (fixing components) and channel inserts up to 1000 kN In-house method OP-16 Tightening torque test of anchor bolts up to In-house method OP-79 1000 Nm Tightening torque control method of BS 4604-1: 1970 Cl. 4.3 fastener/nut assemblies up to 1000 kN BS 4604-2: 1970 Cl. 4.2
Scope of Accreditation Registration No. HOKLAS 104 Page 15 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Welds Bend test on welds in metallic materials BS 4872: Part 1: 1982 Cl. 19.2 & 19.3 (destructive) BS EN 910: 1996 BS EN ISO 5173: 2010 + A1: 2011 Charpy V-notch impact test on welds in BS EN 10045-1: 1990 or BS EN ISO 148-1: 2010 metallic materials in conjunction with the following specification(s): BS EN 875: 1995 BS EN ISO 148-1: 2010 in conjunction with the following specification(s): BS EN ISO 9016: 2012 Cruciform test on welds in metallic materials BS 709: 1983 (A1, A2 & A3) Cl. 5.2 Fracture test on welds in metallic materials BS 709: 1983 (A1, A2 & A3) Cl. 8 BS 4872: Part 1: 1982 Cl. 19.4 & 19.5 BS EN 1320: 1997 BS EN ISO 9017: 2013 Hardness test on welds in metallic materials – BS EN ISO 6507-1: 2005 Vickers hardness test – HV5 and HV10 in conjunction with the following specification(s): BS EN 1043-1: 1996 BS EN ISO 9015-1: 2011 Macroscopic examination on welds in metallic BS 4872-1: 1982 Cl. 19.1 materials BS 7123: 1989 Cl. 12.3.6 BS EN 1321: 1997 BS EN ISO 17639: 2013 Tensile test on welds in metallic materials BS 7123: 1989 Cl. 12.3.5 in the force range of 0.4 kN to 1500 kN BS EN 10002-1: 2001 or BS EN ISO 6892-1: 2009 in conjunction with the following specification(s): BS EN 876: 1995 BS EN 895: 1995 BS EN ISO 4136: 2012 BS EN ISO 5178: 2011
Scope of Accreditation Registration No. HOKLAS 104 Page 16 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Welds Visual examination BS 5289: 1976 (non-destructive) BS EN 970: 1997 ISO 17637: 2003 BS EN ISO 17637: 2011 Magnetic particle test BS 6072: 1981 (1986) (Magnetic flow method colour contrast technique using permanent magnets, D.C. & A.C. yokes) BS EN 1290: 1998 (Magnetic flow method colour contrast technique using permanent magnets, D.C. & A.C. yokes) BS EN ISO 9934-1:2001 (Magnetic flow method colour contrast technique using permanent magnets, D.C. & A.C. yokes) BS EN ISO 9934-1:2015 (Magnetic flow method colour contrast technique using permanent magnets, D.C. & A.C. yokes) ISO 17638: 2003 (Magnetic flow method colour contrast technique, using permanent magnets, D.C. & A.C. yokes) BS EN ISO 17638: 2009 (Magnetic flow method colour contrast technique, using permanent magnets, D.C. & A.C. yokes) Liquid penetrant test BS 6443: 1984 (Colour contrast method) BS EN 571-1: 1997 (Colour contrast method) BS EN ISO 3452-1: 2013 (Colour contrast method) ISO 3452-1: 2013 (Colour contrast method) Ultrasonic test BS 3923: Part 1: 1986 (butt welds in plates and pipes, ‘T’- joint welds, nozzle welds & node welds) BS EN 1714: 1998 (butt welds in plates and pipes, ‘T’- joint welds, nozzle welds & node welds) ISO 17640: 2010 (Butt welds in plates and pipes, ‘T’ joint welds, nozzle welds & node welds) BS EN ISO 17640: 2010 (Butt welds in plates and pipes, ‘T’ joint welds nozzle welds & node welds)
Scope of Accreditation Registration No. HOKLAS 104 Page 17 of 17 Issue Date: 22 February 2017 Ref: HOKLAS104-89
A.E.S. Destructive and Non-Destructive Testing Limited 安捷材料試驗有限公司
104 TEST CAL
Flat F, 2/F, Block 2, Kwai Tak Industrial Centre, 15-33 Kwai Tak Street, Kwai Chung, New Territories, Hong Kong 香港新界葵涌葵德街 15-33 葵德工業中心第二座二字樓 F
Construction Materials 建築材料
ITEM TESTED OR MEASURED 測試或量度項目
SPECIFIC TEST OR PROPERTY MEASURED 特定測試或量度的特性
SPECIFICATION, STANDARD METHOD OR TECHNIQUE USED
規範、標準方法或應用技術 Welds Radiographic examination BS EN 1435: 1997 (Gamma Ray & X-ray) (non-destructive) BS 2600: Part 1: 1983 (Gamma Ray & X-ray) (cont’d) BS 2910: 1986 (Gamma ray & X-ray) BS EN ISO 17636-1: 2013 (Gamma ray & X-ray) ISO 17636-1: 2013 (Gamma ray & X-ray)
