Upload
eric-cui
View
70
Download
2
Embed Size (px)
Citation preview
AWE-16A ELECTRO-SPARK DEPOSITION WELDING MACHINE
AN EASY WAY TO REPAIR YOUR CASTING DEFECTS & SAVING YOUR COST
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD 1
There are blow hole defects and sand hole defects problems for all foundries.
Normally around 5-15% will have such problems (gray iron/ductile iron
castings and non-ferro castings). Most of the defects will appear after machining.
All of the defect castings will become foundry returns if they can not be repaired. For re-melting those foundry returns will have more cost - power
consumption / labour cost / raw material cost etc.
To use ATOM AWE-16A welding machine will repair those defect castings and save your cost up to 10-30%
ATOM AWE-16A is suitable for: Ductile iron casting / Gray iron casting / Aluminum casting / Copper casting and other non-ferro castings.
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD 2
1: CASTING DEFECTS REPAIRING
Foundry mould need to be repaired frequently, due to some damages will happen to make the surface not smooth any more, this will affect the final
products.
Instead of replace with a new mould, to use ATOM AWE-16A welding machine will repair those problems, after polishing the damaged mould will be just like a new one.
Different welding rod materials are available for different metals.
It can also be used for repairing machinery parts and hydraulic equipments.
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD 3
2: FOUNDRY MOULD REPAIRING
High technology : Over 20 improvements, Use chopped wave soft switch
technology and DSC processor, digital control and very accurate output.
Power : Inverter power, energy conservation, environmental protection, high
efficiency, stable, light and smart.
High precision welding : Big current output range, Suitable for Ductile Iron;
Gray Iron; Stainless Steel and Non-ferrous metal (Aluminum , Copper etc. ), can
repair blow hole and sand hole defects, welding speed more quickly.
High welding intensity : With high single point power output, each point of
welding material is combined with the welding molten state to the substrate ,
forming metallurgical combination, produce very strong combination, minimal
chromatic aberration. Easy to operating, any one without professional training
can use and no pollution while using.
Other usage : Can also be used for repairing of mould; hydraulic equipments;
machineries etc.
AWE-16A PARAMETERSMODEL: AWE-16A INPUT VOLTAGE: AC220V
POWER OUTPUT: 1200W VOLTAGE RANGE: 10-100V
FREQUENCY: 50-500HZ OUTPUT PERCENTAGE: 10-100%
NET WEIGHT: 23KGS MACHINE SIZE: 405*210*450MM
ELECTRODE DIA.: 1.0-3.2MM
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD 4
3: MAIN FEATURES AND ADVANTAGES
HIGH SPEED WELDING, FIX HOLE SIZE FROM SEVERAL MICROMETER TO SEVERAL MILLIMETER
HIGH WELDING STRENGTH, NO ANNEALING AND DEFORMATION.
ONLY 1200W PORWER OUTPUT, BUT 3 TIMES FASTER THAN SIMILAR 3000W WELDING EQUIPMENTS. ENERGY SAVING AND STABLE PERFORMANCE.
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD 5
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD 6
1: GRAY IRON CASTING WELDING PERFORMANCE
2: DUCTILE IRON CASTING WELDING PERFORMANCE
3: ALUMINUM WELDING PERFORMANCE
4: WELDING PERFORMANCE
Defect hole After welding After polishing
Defect hole After welding After polishing
Defect hole After welding After polishing
Advantage of AWE-16A compare to ARGON-ARC WELDING and LASER BEAM WELDING
ITEMS AWE-16A ARGON-ARC WELDINGLASER BEAM
WELDING
1, Heat output to mold low very high low
2, Deformation and undercut to the mold no big small
3, Binding strength to the parent material good good good
4, Welding thickness of surfacing (mm) 1mm >0.3mm
5, Welding thickness control very easy very difficult difficult
6, Difficulty of welding on the edges and corners very easy easy very easy
7, Difficulty of pinhole fix easy easy easy
8, Difficulty of fix hold bottom and side very easy difficult difficult
9, Welding speed fast very fast fast
10, Fine welding method easy by hand need EDM machine easy by hand
11, Fine welding time required short time long time middle time
12, Fix defect size small to big middle to big small
13, Machine size small middle big
14, Fix at scene able not able not able
15, Welding direction front / up / down down down
16, Preheat required no need required no need
17, Material match steel;aluminum;copper; alloy etc. steel and aluminum steel and aluminum
18, Consumption materials
all kinds of steel stick only welding stick only welding stick
19, Protection gas argon argon argon
20, Welding cost very cheap very expensive normal
21, Equipment price normal cheap expensive
22, Operation safety safe strong ultraviolet rays radiation rays
YES
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD 7
5: COMPARE TO OTHER WELDING MACHINE
Working principle of AWE-16A:
Electro-spark deposition process is to use the high-energy power stored and release instantly between electrode and matrix with high frequency release, through air ionization channels formed between the electrode and matrix to generate an instant high temperature, high pressure micro-region. While ion state of the electrode materials in micro-melt into the matrix, forming metallurgical combination. Not only due to quenching of metal surface to form martensite, and also deposition process of the narrow transition region to form ultra-fine austenitic organization. So electro-spark deposition process is not normal welding or coating process.
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD. Address: No.16, Liaoyang East Road, Qingdao, China.
Contact: Mr.Eric Cui Email: [email protected]
Phone: 008618661811965 www.atomwelding.com www.welding-machine.cn
QINGDAO ATOM WELDING EQUIPMENTS CO.,LTD 8
6: CONTACT
mailto:[email protected]?subject=http://www.atomwelding.comhttp://www.welding-machine.cn