“Big Red” TEFC-950L

Combination Loaded Container Handler / ForkliftPreliminary SpecificationsRated Container Capacity 77,000-lbs. (34,927 kg) For 3-high Stacking

102.75-in. (2,610 mm) Center of Load

Rated Fork Lift Capacity 83,500-lbs. (37,876 kg)

48-in. (1,219 mm) Load Center

225-in. (5,715 mm) Wheelbase

�

“Big Red” TEFC-950L Combination Loaded Container Handler / Forklift

Manufacturer’s Name TAYLOR

Manufacturer’s Designation TEFC-950L Combination Container Handler / Forklift

Container Handlerw/Std. 7-ft. (2.1 m) Forks

Forkliftw/Std. 7-ft. (2.1 m) Forks

English Metric English MetricRated Fork Lift Capacity At 48-in. (1,219 mm) Center Of Load lb (kg) N/A N/A 83,500 37,876

Rated 3-high Stacking Capacity At 102.75-in. (2,610 mm) Center Of Load (Ctr. Of Load To Ctr. Of Axle) lb (kg) 77,000 34,927 N/A N/A

Load Moment With Forks in-lb (m-kg) N/A N/A 9,205,875 106,065

Load Moment With Attachment in-lb (m-kg) 7,911,750 91,155 N/A N/A

Tractive Effort At Stall lb (kN) 45,462 202 45,462 202

Drive Axle lb (kg) 112,200 50,894 86,300 39,146Vehicle Weight - Empty

Steer Axle lb (kg) 50,300 22,816 58,500 26,536

Drive Axle lb (kg) 224,363 101,771 210,715 95,580Vehicle Weight - Loaded

Steer Axle lb (kg) 15,136 6,866 17,585 7,977

Attachment Weight (2040-FTP) lb (kg) 17,800 8,074 17,800 8,074

Empty % 26.5Gradeability At 0.9 Coef.

Loaded % 16.7

Center Of Truck % 46Grade Clearance

Rear Overhang % 70

Tires 18.00 R25 Radial

Machine Dimensions

1 - Width Across Counterweight in (mm) 120 3,048

2 - Tread Width, Drive Axle in (mm) 128 3,251

3 - Width Over Drive Tires in (mm) 172 4,369

4 - Outside Turn Radius (Tailswing) in (mm) 295 7,493

5 - Inside Turn Radius in (mm) 10 254

6 - Height To Top Of Cab in (mm) 162 4,115

7 - Height To Top Of Counterweight in (mm) 81 2,057

8 - Steer Axle CL To Rear Of Counterweight in (mm) 43 1,092

9 - Wheelbase in (mm) 225 5,715

10 - Underclearance in (mm) 12 305

11 - Drive Axle CL To Carriage Face in (mm) 62.25 1,581

11A - Drive Axle CL To Face Of Minimum in (mm) 54.75 1,39111A - Drive Axle CL To Face Of 8-ft. (2.4 m) Wide Container Maximum With Reach in (mm) 61.25 1,556

12 - Overall Length in (mm) 330.25 8,388

Attachment Dimensions 20-ft. (6.1 m) Container 40-ft. (12.2 m) Container

Expanded in (mm) 480 12,19213 - Length Of Attachment (Nominal)

Retracted in (mm) 240 6,096

14 - Width Of Attachment in (mm) 96 2,438

15 - Inner Mast Face To Side Of Minimum in (mm) 17 43215 - Inner Mast Face To Side Of 8-ft. (2.4 m) Wide Container Maximum With Reach in (mm) 23.5 597

16 - Turn Radius, Far Corner (Retracted) in (mm) 263 6,680 368 9,347

17 - Turn Radius, Near Corner (Retracted) in (mm) 153 3,886 206 5,232

18 - Sideshift (In Carriage) ± in (mm) 9 229

19 - Slewing (5�) in (mm) 25 635 50 1,270

20 - Pile Slope, 3� End To End (Non-powered) in (mm) 10.2 259 20.4 518

21 - Length Of ISO Twistlock Below Attachment (Nominal) in (mm) 4 102

22 - Top Of Fork To Tip Of Twistlock in (mm) 48 1,219

23 - Fork Spread (Outside) in (mm) 146.5 3,721

Travel And Lift Speeds Empty Loaded

Travel Speed (Max) - Forward And Reverse mph (km/h) 13.9 22.4 12 19.3

Lift Speed (Max) fpm (m/s) 41 0.2 39 0.2

33-ft. Mast (10.1 m) Upright Dimensions Minimum Maximum

Fully Lowered in (mm) 305.5 7,760A - Height To Top Of Mast

Fully Raised in (mm) 503.5 12,789

B - Height To Top Of Carriage in (mm) 99.25 2,521 495.25 12,579

C - Height To Tip Of Twistlock in (mm) –42 (belowground)

–1,067 (belowground) 354 8,992

NOTE: Performance specifications are for machines equipped as described on the back page of this specification sheet. Performancespecifications are affected by the condition of the vehicle, its components, and the nature and condition of the operating area. If thesespecifications are critical, the proposed application should be discussed with your Taylor sales representative.

“Big Red” TEFC-950L Combination Loaded Container Handler / Forklift

B

B

C

C

1415

11A

12

9

19

8

7

6

A

A

2220

2233

13

21

1

4

18

16

18

19

17

5

Twistlock Detail

10

EngineCummins QSM11-330 (meets all 2001 EPA Tier II emissionsregulations) electronic turbocharged, charged air after cooled (air toair) diesel engine has 330 (246 kW) gross brake horsepower at2100 rpm and 340 (254 kW) gross horsepower at 1800 rpm. The4-cycle in-line 6 cylinder engine has 661 cubic inch (11 liter)displacement. The bore is 4.92 in. (108 mm) x 5.79 in. (146 mm)stroke. Peak torque is 1170 ft.-lbs (1586 N-m) at 1400 rpm (SAEJ1349). This peak torque is maintained from 1100 to 1400 rpm.Standard features are electronic diagnostic and maintenancemonitor, fuel/water separator and engine/transmission protectionsystems. The fuel tank capacity is 125 gallons (473 L).

Air CleanerThe 2-stage, heavy-duty, dry air cleaner with restriction indicatoris easily serviced.

Cooling SystemThe deaeration tank, with a sight gauge for checking coolantlevel, provides optimum engine cooling.

Electrical, Instrumentation, and AccessoriesThe one-piece instrument panel is pre-wired to accommodateheavy-duty accessories and flips down for easy servicing. Allwiring is color coded.The unit has a 12-volt electrical system. Standard equipmentincludes a full-kill engine / transmission protection system,key-type anti-restart ignition system, two 220 amp-hourbatteries, 100-amp alternator, main battery disconnect switch,mechanical pressure gauges, electrical temperature gauges,thermal reset circuit breakers, and lighted instruments.Eight worklights (four front, two rear, two on the attachment),key-switch actuated amber strobe light, forward alarm,reverse-actuated warning alarm, rear-view mirror, and air hornare standard.Gauges include fuel level, ammeter, hourmeter, air pressure,engine oil pressure, engine coolant temperature, transmissionoil pressure, transmission oil temperature, seat belt light, low airlight, engine service required light, engine system fault light,engine shutting down light and parking brake light.

TransmissionThe three-speed, fully reversing, modulated, powershifttransmission has declutch with brakes behind the declutchfeature and electric shift control. The filler pipe dipstick andlarge, heavy-duty oil filter are easily accessible. Separateair-to-oil cooler. The integrally built torque converter hasconstant-mesh gear sets actuated by hydraulic clutch packs.

Drive AxleThe high-stability, wide stance, planetary drive axle’s housing isbolted to the frame.

Steer AxleThe single-cylinder steer axle design with tapered wheel andkingpin bearings is fully sealed and never needs adjusting.

Brake SystemThe internal force-cooled, wet disc service brakes areair-actuated. The drive-line brake is spring applied for parking.

Power SteeringThe hydrostatic steering system provides constant response atall engine speeds.

ChassisThe all-welded frame has an integral, sloped counterweight.Hinged doors provide easy access to all service points. The

elevated, center mount operator and overhead guard with2-door cab tilts forward to aid in engine removal. The cab isequipped with a 25,000 BTU heater, front windshield wiper, anddefroster fan. The adjustable air suspension seat hasadjustable-angle armrests and an operator seat belt.

Hydraulic SystemThe large capacity hydraulic tank has a spin-on tank breather,dual wire-mesh stainers, and a full-flow, 10-micron, return-linefilter with a replaceable element in the tank. The filter conditionindicator is mounted on the instrument panel. The tank refillcapacity is 195 gallons (738 L).The gear-type pumps are converter driven. Control valves areseparate, stacked, spool-type. The tilt-lock valve prevents mastdrift and torsional stress.The self-aligning, bearing-mounted, lift cylinders have chromeplated rods and self-adjusting packing. The pilot operatedcontrols are conveniently located. The valves are controlledwith hydraulic remotes. An accumulator is standard.

Mast, Carriage, and RollersThe 33-ft. (10 m) ULTRA-VU mast provides the operator withmaximum visibility; the telescopic, nested-channel mast hastwo multiple-leaf lift chains and is constructed of high-strengthsteel for minimum weight. Two lifting eyes and bolt-on capspermit safe, easy removal.The 148-in. (3,759 mm) “C” type side shift carriage andattachment are constructed of high-strength steel and designedfor high visibility.Carriage side rollers are adjustable to compensate for wear. Allrollers can be lubricated.

ForksForged from heat treated alloy steel for lift truck specifications.Fork size: 6-in. x12-in. x 84-in. (152 mm x 305 mm x 2,134 mm)

Container AttachmentExpandable, fork-mounted container handling attachment forhandling loaded 20’ through 53’ (6.1 m through 16.1 m) ISOcontainers in widths of 8’ (2.4 m) and 8’ 6” (2.6 m) with amaximum weight of 77,000-lbs. Includes all hydraulics,electrical circuitry, and an electrical signal system for operationof the attachment. The attachment has 18-in. (458 mm) of sideshift total, (9-in (229 mm) in each direction), 5° of slew on eachend, 6.5-in. (165 mm) of reach on each side of the attachment,and 3° of non-powered pile slope. Containers more than 40’(12.2 m) long must have the standard 40’ (12.2 m) ISO pickuppoints. Controls in the cab energize valves on the attachment tooperate side shift, twistlocks, expansion, and left and right handslew. A twistlock safety interlock system ensures correct lockingprocedure. Signal lights are amber, green, and red. Twoworklights are standard. Double stack guide arms set for 8’6”(2.6 m) wide containers are standard.

This vehicle is certified to meet the applicable design and performance criteriarequired for Powered Industrial Trucks in OSHA Safety and Health Standards, Title29 CFR, Part 1910.178, and the applicable design and performance requirementsin ANSI B56.1 that were in effect at the time of manufacture. These standards alsoapply to the user and should be adhered to while operating this vehicle.

All specifications are subject to change without notice. Some operating datamay be affected by the condition of the operating area. If these specifications arecritical, contact the factory.

“Big Red” TEFC-950L Combination Loaded Container Handler / Forklift

Taylor Machine Works, Inc.Printed in U.S.A.

K1 (9/02)

650 North Church AvenueLouisville, Mississippi 39339-2017

Phone (662) 773-3421 Fax (662) 773-9146