BMW e60 Engine Seals Notebook

Embed Size (px)

Citation preview

  • 8/11/2019 BMW e60 Engine Seals Notebook

    1/24

    Pasted from

    No. Description Supplement Qty From Up To Part Number Price Notes

    1 IGNITION COIL COVERING ZYL. 1-4 1 11127511180 $43.31

    2 IGNITION COIL COVERING ZYL. 5-8 1 11127511181 $43.31

    3 Cover lid 1 Mar-10 11127509328 $7.78

    4 sealing 2 11127518420 $5.69

    5 Screw 4 11127521756 $0.72

    Intake-side

    6 Pulse generator, camshaft 2 12147539172 $116.05

    Exhaust-side

    6 Pulse generator, camshaft 2 12147518628 $116.05 See MH 9790718

    7 O-ring 17X3 4 12141748398 $1.20

    8 Screw 4 11127521756 $0.72

    9 Support 4 11127546661 $3.17

    10 Screw 4 11127521756 $0.72

    Acoustic CoveringWednesday, September 05, 2012

    8:12 PM

    Acoustic Covering Page 1

    http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3821&hg=11&fg=15http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3821&hg=11&fg=15http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3821&hg=11&fg=15
  • 8/11/2019 BMW e60 Engine Seals Notebook

    2/24

    Pasted from

    No. Description Supplement Qty From Up To Part Number Price Notes Ph

    1 Cylinder head cover ZYL. 1-4 1 Nov-06 11127563474 $434.00only in conjunction with

    -- Cable clamp 1 Nov-06 11787549563 $1.04

    -- Vent pipe ZYL. 1-4 1 Nov-06 11617563476 $74.79

    2 Gasket set, cylinder head cover ZYL. 1-4 1 11127513194 $83.31

    3 Cylinder head cover ZYL. 5-8 1 11127522159 $434.00

    4 Gasket set, cylinder head cover ZYL. 5-8 1 11127513195 $83.31

    5 Gasket ring 2 11127502482 $3.35

    6 Rubber grommet 4 11127501588 $1.07

    7 Cable clamp 2 May-10 12527528508 ENDED

    7 Cable clamp 2 7147575208 $0.89

    8 Cable holder ZYL. 5-8 2 12527510935 $1.77

    9 Fastening elements M6X46 10 11127568838 $3.17

    10 Rubber seal 16 11127511582 $2.69

    11 Cap nut M7 8 11127568834 $3.17

    12 Cap nut M7/M5 8 11127568835 $3.17

    13 Repair kit, pressure regulating valve 2 11127547058 $20.24

    Valve/Head CoverWednesday, September 05, 2012

    8:21 PM

    Valve Head Cover Page 2

    http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3258&hg=11&fg=15http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3258&hg=11&fg=15http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3258&hg=11&fg=15
  • 8/11/2019 BMW e60 Engine Seals Notebook

    3/24

    BMW TIS - 11 12 006 Removing and installing/sealing right cylinder head c

    (N62/N62TU)

    11 12 006 Removing and installing/sealing right cylinder head cover

    (N62/N62TU)

    (cylinder bank 1 to 4)

    Remove design cover

    Remove acoustic cover

    Remove centre of assembly partition wall

    Remove electronics box cover.

    Remove electronics box seal.

    These work steps are described in the section Replacing control Remove ignition coil cover.

    Remove intake filter housing (without raw air housing).

    Remove intake hose with air-mass flow sensor

    Note:

    For purposes of clarity, the following work steps are shown on th

    engine after it has been removed.

    Unlock plug (1) and remove.

    Release screws and remove sealing element . Remove sens and .Installation:

    Replace sealing element .Replace sealing rings on sensors and .

    Removing ignition coils.

    Valve Head Cover Page 3

  • 8/11/2019 BMW e60 Engine Seals Notebook

    4/24

    Release both grounding cables.

    Unlock and detach vent hose.

    Unclip cable duct and remove cable from holder.

    Remove servomotor for right eccentric shaft .

    Unfasten screws.

    Remove spacer upwards.Replace seal.

    Remove injection pipe .

    Release screw connections (1, 2, 3 and 4).

    Remove cylinder-head cover.

    Installation:

    Note installation direction of sealing ring .Groove in sealing ring points outwards.

    Replace sealing ring and press into cylinder head cover unflush.

    Installation:

    Replace seal (1).

    Align gasket loosely in cover groove. Starting at corner rasecure gasket in cover groove and press into groove soit is free of tension.

    Installation:

    Make sure sliding rails are correctly seated when mounting on

    cylinder head.

    Valve Head Cover Page 4

  • 8/11/2019 BMW e60 Engine Seals Notebook

    5/24

    Installation:

    Replace spark plug domes.

    Coat rubber seals on spark plug dome with anti-friction rubbcoating.

    Installation:

    Install spark plug domes in cylinder head.When fitting cylinder head cover:

    Align spark plug domes to cylinder head cover.

    Installation:

    Clean seal residue from sealing surfaces.

    Coat contact surfaces of joint with Drei Bond 1209 (refer to BMW

    Parts Service).

    Installation:

    Clean seal residue from sealing surfaces.

    Apply a thin, uniform bead of Drei Bond 1209 sealing agent (refe

    BMW Parts Service) to transition area of half-moon sections.

    Replace sealing elements .

    Installation:

    Make sure gasket is correctly seated at sides and on rear side of

    cylinder head.

    Installation:

    Screw connections (1, 2, 3 and 4) of cylinder head cover are

    different .Replace screw connections .Move cylinder head cover with gasket into assembly position.

    Secure cylinder head cover, starting with screw connection ffront .Tighten down screw connections (1, 2 and 3) in diagonal sequen

    from inside to outside.

    Valve Head Cover Page 5

    http://tis.spaghetticoder.org/s/view.pl?1/07/45/46
  • 8/11/2019 BMW e60 Engine Seals Notebook

    6/24

    Pasted from

    BMW TIS - 11 12 005 Removing and installing/sealing left cylinder head co

    (N62/N62TU)

    11 12 005 Removing and installing/sealing left cylinder head cover

    (N62/N62TU)(cylinder bank 5 to 8)

    Necessary preliminary tasks:

    Remove design cover

    Remove acoustic cover

    Remove centre engine compartment partition wall

    Remove ignition coil cover

    BMW ALPINA B7 vehicles:

    - Remove radial compressorNote:

    For purposes of clarity, the following work steps are shown on th

    engine after it has been removed.

    Unclip cable holder with cables.Pull tank venting valve off holder.

    Unlock plug (1) and remove.

    Release screws and remove sealing element .Remove sensors and .Installation:

    Replace sealing element .Replace sealing rings on sensors and .

    Removing ignition coils.

    Valve Head Cover Page 6

    http://tis.spaghetticoder.org/s/view.pl?1/07/45/46http://tis.spaghetticoder.org/s/view.pl?1/07/45/46http://tis.spaghetticoder.org/s/view.pl?1/07/45/46
  • 8/11/2019 BMW e60 Engine Seals Notebook

    7/24

    Release both grounding cables.

    Unlock and detach vent hose.

    Unclip cable duct and remove cable from holder.

    Remove servomotor for left eccentric shaft .

    Unfasten screws.

    Remove spacer upwards.Installation:

    Replace sealing ring.

    Remove injection pipe

    Release screw connections (1, 2, 3 and 4).

    If necessary, pull out oil dipstick.

    Remove cylinder head cover.

    Installation:

    Note installation direction of sealing ring .Groove in sealing ring points outwards.

    Replace sealing ring and press into cylinder head cover unflush.

    Installation:

    Replace seal (1).

    Align gasket loosely in cover groove. Starting at corner rasecure gasket in cover groove and press into groove soit is free of tension.

    Installation:

    Replace spark plug domes.

    Coat rubber seals on spark plug dome with anti-friction rubbcoating.

    Valve Head Cover Page 7

  • 8/11/2019 BMW e60 Engine Seals Notebook

    8/24

    Installation:

    Install spark plug domes in cylinder head.

    When fitting cylinder head cover:

    Align spark plug domes to cylinder head cover.

    Installation:

    Clean seal residue from sealing surfaces.Coat contact surfaces of joint with Drei Bond 1209 (refer to BMW

    Parts Service).

    Installation:

    Clean seal residue from sealing surfaces.

    Apply a thin, uniform bead of Drei Bond 1209 sealing agent (refe

    BMW Parts Service) to transition area of half-moon sections.

    Replace sealing elements .

    Installation:

    Make sure gasket is correctly seated at sides and on rear side of

    cylinder head.

    Installation:

    Screw connections (1, 2, 3 and 4) of cylinder head cover are

    different.

    Replace screw connections .Insert screw connections (1, 2 and 3) without pretension and alig

    cover.

    Tighten down screw connections (1, 2 and 3) in diagonal sequenc

    from inside to outside.

    Pasted from

    BMW TIS - 12 13 511 Replacing ignition coil (N62)

    12 13 511 Replacing ignition coil (N62)

    Valve Head Cover Page 8

    http://tis.spaghetticoder.org/s/view.pl?1/07/45/43http://tis.spaghetticoder.org/s/view.pl?1/07/45/43http://tis.spaghetticoder.org/s/view.pl?1/07/45/43
  • 8/11/2019 BMW e60 Engine Seals Notebook

    9/24

    Necessary preliminary tasks:

    Remove acoustic cover .

    BMW ALPINA B7 vehicles:

    - Remove radial compressor .

    Pull ignition coil covers out of rubber

    grommets.

    Unlock plug fastener of ignition coil.

    Disconnect plug.Pull out ignition coil .This procedure is applicable to all ignition coils.

    Valve Head Cover Page 9

  • 8/11/2019 BMW e60 Engine Seals Notebook

    10/24

    Installation:

    Insert rubber seal on ignition coils betweenguides.

    Note:

    Read out fault memory of DME control unit.

    Check stored fault messages.

    Rectify faults.

    Now clear the fault memory.

    Switch off ignition.Pasted from

    Valve Head Cover Page 10

    http://tis.spaghetticoder.org/s/view.pl?1/07/45/75http://tis.spaghetticoder.org/s/view.pl?1/07/45/75http://tis.spaghetticoder.org/s/view.pl?1/07/45/75
  • 8/11/2019 BMW e60 Engine Seals Notebook

    11/24

    Sponsored links

    Pasted from

    No. Description Supplement Qty From Up To Part Number Price Notes

    1 Cylinder Head Gasket Asbestos-Free 0,75MM 2 11127513944 $103.85

    1 Cylinder Head Gasket Asbestos-Free 1,05MM (+0,3) 2 11127513945 $119.83

    2 Set Bolt Cylinder Head 2 11127583113 $42.00

    3 Washer 20 11127550856 $0.65

    4 Torx bolt M8X45 4 11127511073 $1.07

    ONLY APPLIES TO CYLINDER 1-4

    5 Shackle 1 11127511609 $4.22

    ONLY APPLIES TO CYLINDER 5-8

    6 Shackle 1 Mar-05 11127511610 $3.14

    7 Hex bolt M8X20-ZNNIV SI 4 Mar-05 7119903039

    8 non-return valve M14X1,5 6 11367539857 $21.87

    9 O-ring 9,5X2,5MM 2 11367507729 $2.92

    10 Connector M8X1 2 11127507532 $4.92

    11 Gasket ring A8X11,5-AL 2 7119963041 $0.57

    12 Spark plug pipe 8 11127570219 $27.00

    13 OIL PRESSURE SWITCH M12X1,5 1 12617568480 $11.70 +core

    13 OIL PRESSURE SWITCH M12X1,5 1 12617620512 +core

    14 Gasket Set Cylinder Head Asbestos Free 1 11127518017 $430.17

    Cylinder HeadWednesday, September 05, 2012

    8:31 PM

    Cylinder Head Attach Page 11

    http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3257&hg=11&fg=15http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3257&hg=11&fg=15http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3257&hg=11&fg=15
  • 8/11/2019 BMW e60 Engine Seals Notebook

    12/24

    only in conjunction with

    -- Gasket Steel 2 11617521181 $36.04

    Gasket set without cyl.head gasket

    Cylinder Head Attach Page 12

  • 8/11/2019 BMW e60 Engine Seals Notebook

    13/24

    Sponsored lin

    Pasted from

    No. Description Supplement Qty From Up To Part Number Price Notes Phot

    2 Vent pipe ZYL. 1-4 1 Oct-04 Nov-04 11617532514 ENDED

    2 Vent pipe ZYL. 1-4 1 Oct-04 Nov-06 11617547185 $55.65

    only in conjunction with

    -- Vent pipe ZYL. 5-8 1 Oct-04 Nov-06 11617547186 $55.65

    3 Vent pipe ZYL. 5-8 1 Oct-04 Nov-04 11617532515 ENDED

    3 Vent pipe ZYL. 5-8 1 Oct-04 Nov-06 11617547186 $55.65

    only in conjunction with

    -- Vent pipe ZYL. 1-4 1 Oct-04 Nov-06 11617547185 $55.65

    Vent PipesWednesday, September 05, 2012

    8:40 PM

    Vent Pi es Pa e 13

    http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3259&hg=11&fg=15http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3259&hg=11&fg=15http://www.realoem.com/bmw/showphoto.do?id=11617547185http://www.realoem.com/bmw/showphoto.do?id=11617547186http://www.realoem.com/bmw/showphoto.do?id=11617547186http://www.realoem.com/bmw/showphoto.do?id=11617547185http://www.realoem.com/bmw/showphoto.do?id=11617547185http://www.realoem.com/bmw/showphoto.do?id=11617547186http://www.realoem.com/bmw/showphoto.do?id=11617547186http://www.realoem.com/bmw/showphoto.do?id=11617547185http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3259&hg=11&fg=15
  • 8/11/2019 BMW e60 Engine Seals Notebook

    14/24

    Sponsored links

    Pasted from

    No. Description Supplement Qty From Up To Part Number Price Notes

    1 Eccentric shaft ZYL. 1-4 1 11377541880 $748.19 +core

    1 Eccentric shaft ZYL. 5-8 1 11377541883 $748.19 +core

    2 Needle bearing 8 Jul-10 11377500978 ENDED

    2 Needle bearing 8 11377615379

    3 Magnetic wheel 2 11377534164 $50.82

    4 Fillister-head screw f magnetic wheel M6X20-A2 2 7119903465 $0.74

    5 Eccentric shaft sensor 2 11377527017 $367.58

    6 Isa screw with washer M5X16-Z1-ZNS 6 7129902329 $0.60

    7 Oil spray tube ZYL. 1-4 1 11427504496 $31.28

    7 Oil spray tube ZYL. 5-8 1 11427504497 $31.28

    8 Fixing clamp 8 11427507967 $0.35

    9 Hex bolt M7X8 4 11427512942 $0.61

    10 Hex bolt M8X50 2 11317501744 $1.07

    11 Actuator 2 11377548389 $295.22

    12 Fillister-head screw M5X12-ZNNIV SI 8 7119902859 $2.35

    13 Spacer 2 11377514508 $12.85

    14 O-ring 53,0X2,0MM 2 7119903596 $2.51

    Camshaft ActuatorWednesday, September 05, 2012

    8:42 PM

    Camshaft Actuator Page 14

    http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3606&hg=11&fg=25http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3606&hg=11&fg=25http://www.realoem.com/bmw/showparts.do?model=NB33&mospid=47759&btnr=11_3606&hg=11&fg=25
  • 8/11/2019 BMW e60 Engine Seals Notebook

    15/24

    15 Torx bolt M5X30-A2 8 7129900465 $1.54

    16 AT-Valvetronic control unit 1 11377575654 $473.05

    17 Socket housing, blue 1 12527515464 $6.70

    only in conjunction with

    -- Rubber grommet 9 12527503411 $0.18

    -- Terminal socket for MLK 1,2 0,35 MM/AG 9 12527564537 $0.50

    BMW TIS - 11 37 024 Removing and installing/replacing servomotor for right

    eccentric shaft (N62/N62TU)

    11 37 024 Removing and installing/replacing servomotor for right

    eccentric shaft (N62/N62TU)

    Important!

    Follow instructions issued by diagnosis tester.

    Risk of damage to intermediate shaft.

    (cylinder bank 1 to 4)

    Necessary preliminary tasks:

    Connect diagnosis tester

    Remove acoustic cover

    Remove ignition coil cover

    Important!

    Follow instructions issued by diagnosis tester.Unlock plug on servomotor and disconnect.

    Unfasten screws.

    Rotate servomotor until no longer engaged in splinteeth of eccentric shaft.

    Camshaft Actuator Page 15

  • 8/11/2019 BMW e60 Engine Seals Notebook

    16/24

    Installation:

    Replace sealing ring on spacer.

    Install servomotor and screw in up to spacer.Rotate servomotor into correct installation positionInstall and tighten down screws.

    Installation:

    Read out fault memory of control unit of Digital Motor

    Electronics (DME).

    Check stored fault messages.

    Rectify faults.

    Now clear the fault memory.

    Pasted from

    BMW TIS - 11 37 022 Removing and installing/replacing servomotor for left

    eccentric shaft (N62/N62TU)

    11 37 022 Removing and installing/replacing servomotor for left

    eccentric shaft (N62/N62TU)

    Important!

    Follow instructions issued by diagnosis tester.

    Risk of damage to intermediate shaft.

    (cylinder bank 5 to 8)

    Necessary preliminary tasks:

    Connect diagnosis tester.

    Remove acoustic cover

    Remove ignition coil cover

    Important!Follow instructions issued by diagnosis tester.

    Unlock plug on servomotor and disconnect.

    Camshaft Actuator Page 16

    http://tis.spaghetticoder.org/s/view.pl?1/07/45/44http://tis.spaghetticoder.org/s/view.pl?1/07/45/44http://tis.spaghetticoder.org/s/view.pl?1/07/45/44
  • 8/11/2019 BMW e60 Engine Seals Notebook

    17/24

    Unfasten screws.

    Rotate servomotor until no longer engaged in splinteeth of eccentric shaft.

    Installation:

    Replace sealing ring on spacer.

    Install servomotor and screw in up to spacer.Rotate servomotor into correct installation positionInstall and tighten down screws.

    Installation:Read out fault memory of control unit of Digital Motor

    Electronics (DME).

    Check stored fault messages.

    Rectify faults.

    Now clear the fault memory.

    Pasted from

    Camshaft Actuator Page 17

    http://tis.spaghetticoder.org/s/view.pl?1/07/45/41http://tis.spaghetticoder.org/s/view.pl?1/07/45/41http://tis.spaghetticoder.org/s/view.pl?1/07/45/41
  • 8/11/2019 BMW e60 Engine Seals Notebook

    18/24

    Pasted from

    No. Description Supplement Qty From Up To Part Number Price Notes Pho

    1 Timing case cover, top 1 11147506419 $96.98

    2 Gasket Steel 1 11147506424 $12.02

    3 Timing case cover, top 1 11147506422 $96.98

    4 Gasket Steel 1 11147506425 $12.02

    5 Torx bolt M6X20-ZNNIV SI 12 7129905568 $0.44

    6 Torx bolt M6X35-ZNNIV SI 4 7129905572 $0.71

    7 Solenoid valve (SOLV) 4 11367560462 $118.05

    8 O-ring 21,29X1,78 4 11367546379 $1.85