Embedded Box PC B O X E R - 6 3 0 1 V S
BOXER-6301VS
Embedded Box PC
Intel Core i5 Processor
2 USB3.0, 2 USB2.0, 3 COM
3 MiniCard, 3 SIM Sockets
BOXER-6301VS Manual 2nd Ed August 11, 2015
Embedded Box PC B O X E R - 6 3 0 1 V S
Copyright Notice This document is copyrighted, 2015. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, or for any infringements upon the rights of third parties that may result from its use.
The material in this document is for product information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, AAEON assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein.
AAEON reserves the right to make changes in the product design without notice to its users.
i
Embedded Box PC B O X E R - 6 3 0 1 V S
Acknowledgments All other products name or trademarks are properties of their respective owners.
AMI is a trademark of American Megatrends Inc.
CFast is a trademark of the Compact Flash Association.
Intel and Core are trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft Corp.
IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.
Please be notified that all other products name or trademarks not be mentioned above are properties of their respective owners.
ii
Embedded Box PC B O X E R - 6 3 0 1 V S
Packing List
Before you begin installing your system, please make sure that the following materials have been shipped:
1 BOXER-6301VS Embedded Box PC
10 M2 x 3mm screws (S1A5003010)
2 Drive bay keys
1 3-pin Phoenix connector (1652003201)
1 Wallmount bracket
1 Product DVD
If any of these items should be missing or damaged, please contact your distributor or sales representative immediately.
iii
Embedded Box PC B O X E R - 6 3 0 1 V S
Safety & Warranty Please read the following safety instructions carefully. It is advised
that you keep this manual for future references
1. Disconnect this device from any AC supply before cleaning.
2. While cleaning, use a damp cloth instead of liquid or spray
detergents.
3. For any pluggable equipment, the power outlet must be
installed near the device and easily accessible.
4. Keep this device away from humidity.
5. Place this device on a solid surface during installation.
Dropping it or letting it fall could cause damage.
6. The openings on the devices enclosure are for dissipating
heat. DO NOT COVER THE OPENINGS.
7. Watch out for high temperatures that may occur during system
operation.
8. Make sure the voltage of the power source is correct before
connecting the device to the power outlet.
9. Position the power cord so that people cannot step on it. Do
not place anything over the power cord.
10. All cautions and warnings on the device should be noted.
11. If the device is not to be used for a long time, disconnect it
from the power supply to avoid damage by transient
over-voltage.
12. Never pour any liquid into the openings. This could cause fires
iv
Embedded Box PC B O X E R - 6 3 0 1 V S
or electric shocks.
13. As most electronic components are sensitive to static electrical
charge, be sure to ground yourself to prevent static charge
when installing the internal components. Use a grounding wrist
strap and contain all electronic components in any
static-shielded devices.
14. If any of the following situations arises, please the contact our
service personnel:
i. Damaged power cord or plug
ii. Liquid intrusion to the device
iii. Exposure to moisture
iv. Device is not working as expected or in a manner as
described in this manual
v. The device is dropped or damaged
vi. Any obvious signs of damage displayed on the device
15. Do not leave this device in an uncontrolled environment where
the storage temperature is below -10C or above 60C to
prevent damage.
v
Embedded Box PC B O X E R - 6 3 0 1 V S
FCC This device complies with Part 15 FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received including
interference that may cause undesired
operation.
Caution: There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions and your local governments recycling or disposal directives.
vi
Embedded Box PC B O X E R - 6 3 0 1 V S
China RoHS Requirements
AAEON Boxer/ Industrial System
(Pb)
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
O
SJ/T 11363-2006 X
SJ/T 11363-2006
vii
Embedded Box PC B O X E R - 6 3 0 1 V S
China RoHS Requirements
Poisonous or Hazardous Substances or Elements in Products AAEON BOXER PC/ Industrial Systems
Component
Poisonous or Hazardous Substances or Elements
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr(VI))
Polybrominated
Biphenyls
(PBB)
Polybrominated
Diphenyl Ethers
(PBDE)
PCB & Other
Components X O O O O O
Wires &
Connectors
for External
Connections
X O O O O O
Chassis X O O O O O
CPU & RAM X O O O O O
Hard Disk X O O O O O
PSU X O O O O O
OThe quantity of poisonous or hazardous substances or elements found in each of the component's parts is below the SJ/T 11363-2006-stipulated requirement. X: The quantity of poisonous or hazardous substances or elements found in at least one of the component's parts is beyond the SJ/T 11363-2006-stipulated requirement. Note: The Environment Friendly Use Period as labeled on this product is applicable under normal usage only
viii
Embedded Box PC B O X E R - 6 3 0 1 V S
Contents Chapter 1 General Information
1.1 Introduction ................................................................ 1-2
1.2 Features .................................................................... 1-3
1.3 Specifications ............................................................ 1-4
1.4 Notes for Windows Users ........................................ 1-7
Chapter 2 Quick Installation Guide
2.1 Safety Precautions .................................................... 2-2
2.2 Dimensions and I/Os ................................................. 2-3
2.3 List of Jumpers .......................................................... 2-5
2.4 List of Connectors ..................................................... 2-6
2.5 Setting Jumpers ........................................................ 2-7
2.6 MiniCard with mSATA / PCIe Selection (JP1) .......... 2-8
2.7 Clear CMOS Jumper (JP10) ..................................... 2-8
2.8 COM2 Pin8 Function Selection (JP11) ..................... 2-8
2.9 10M/100M/1G Ethernet Port 1 (LAN1) ...................... 2-9
2.10 10M/100M/1G Ethernet Port 2 (LAN2) .................... 2-9
2.11 USB 2.0/3.0 Port 1 & 2 (USB) ............................... 2-10
2.12 COM Port 1, 2, 3 (Serial Port) ............................... 2-11
2.13 VGA Ports (VGA) .................................................. 2-13
2.14 SIM Socket 1, 2, 3(SIM) ........................................ 2-15
2.15 Onboard MiniCard Slot (Full Function) (MiniCard1)
....................................................................................... 2-15
2.16 Internal MiniCard Slot (USB Signal) (MiniCard2, 3)
ix
Embedded Box PC B O X E R - 6 3 0 1 V S
....................................................................................... 2-18
2.17 CFast Slot (CFast) ................................................. 2-20
2.18 DDR3L SODIMM Slot (SODIMM) ......................... 2-22
2.19 PoE 1~4 Port (MID-SPAN) (CN4) ......................... 2-22
2.20 PoE Power on/off (POE Power Switch) ................ 2-23
2.21 DC inlet (DC-in) ..................................................... 2-23
2.22 Hardware Installation............................................. 2-23
2.23 Removing the Baseplate ....................................... 2-23
2.24 Installing the GPS/Wifi/3G/4G Module .................. 2-26
2.25 Inserting SIM Cards............................................... 2-28
2.26 Installing 2.5 Storage Devices .......
