Upload
danghanh
View
224
Download
7
Embed Size (px)
Citation preview
* Subject: Repair guide for Auto Turn-Off (Shuts Off) while watching TV.
Service BulletinBulletin Number: GLZ201600160General Information
* Bulletin Registration Date: 2016.05.23 * Effective from Date: 2016.05.23 ~
•Applicable for models OLED65G6**, OLED77G6**
65/60/55/49UH77**, 65/60/55/49UH87**
55/49/43/32LH60/LH66** N*/U*/S*/D* K /N th A i /S th A i /B il
49/43LH57/59**-Z* : EU/CIS, 55/49/43LH59**-T* : Asia / MEA
55/49/43LH57**-U/D/S/C/T* : North America/South America/ Brazil / China / Hongkong / Asia / MEA
55/49/43LH56**-S* : Brazil, 49/43LH58**-C* : China
Applicable in warranty: YES NO Also applicable outside YES NO
* Applicable Serial Number: Produced 16Y Models before April 2016 (Serial number : ~604xxxxxxx)
55/49/43/32LH60/LH66**-N*/U*/S*/D* : Korea/North America/South America/Brazil
55/49/43/32LH60**-C*/T*/P* : Hong Kong/Asia/MEA(Non-Satellite)
55/49/43/32LH60*V/Y/U/Z-T* : MEA / Asia (Satellite)
55/49/43LH58**-N*, 55/49/43LH6420-N*
43/49LF5400-UE, 40LH5300-UA : North America
**LH54*V-Z*, **LH54*V-T*, 32LH53*V-Z*
Technical Information
of warranty:
Applicable only with symptoms YES NObelow:
Applicable with every repair: YES NO
* 2) Problem / Cause RESET IC Defect (DIODES Inc )
* 1) Symptoms / Customer Complaint- Auto Turn-Off during watching TV
* 3) Solution: (Short explanation of the solution)- Check Power-Off History in the IN-START Menu- If there is ‘POWER_OFF_BY_5VMNT’
- RESET IC Defect (DIODES Inc.)
DIODES CO. (N/G) KEC(OK)
- Replace the RESET ICNew reset IC _Part no. : EAN63491301 (KEC) ( MOQ:1K )
1/2
Detail
Original Inspection
(1): While watching TV, TV automatically shuts off While watching TV,
TV SHUTS OFF
Detail
(2): Check whether TV set is in Standby mode
(3): Turn TV on and Check Power Off History in the IN-START menu.Check “POWER_OFF_BY_5V_MNT”on Power off history (In start -> No.3)
CheckTV set is in Standby mode?
N
Y
y
Some other Defect
Check OFF_BY_5V_MNTIn Power off history (In start item No. 3)
Turn off the TV and proceed with re-work guide on the next page. (4): Turn off the TV and proceed using the re-work guide on the next page.
Note: The pages following the procedure on the next page are IC location guides for each chassis encountered.
Rework Guide
Rework guide for Replacing Reset IC (DIODES Company)
Step 1. Add small amount of solder to all pins (3 Points) of Reset IC i ld i iusing soldering iron.
Rework
Step 2. Remove the Reset IC using 2 soldering irons.Using two soldering irons at the same time like tweezers, remove the Reset IC by carefully lifting the IC off the board.y y g
Step 3. Install the new KEC Reset IC using a soldering iron.
Caution Be careful not to touch other components around the reset IC with the soldering iron.
Basic Information
TV
Rework Guide
OLEDG6 Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Platform H15
Company DIODES Apply model OLED G6
Circuit name IC2304/IC2305 Part no Original p/n:
EAN61829903
Rework Guide
Rework 1. Check work order information 2. Check actual ICs on the board.
DIODES KECIC2305 EAN61829903
IC Location Detailed Picture
3 Replace both reset ICs from DIODES Co to KEC3. Replace both reset ICs from DIODES Co. to KECa) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
IC2304
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).
IC2305
Applied Model OLED65G6**OLED77G6**
Cautiona) The Reset IC is very sensitive, please prevent
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
Request
Basic Information
TV
Rework Guide
UH77/87 Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Platform K2L
Company DIODES Apply model UH77.. / 87..
Circuit name IC2304 Part no Original p/n:EAN61829903
Rework Guide
Rework 1. Check work order information 2. Check actual IC on the board.
DIODES KECEAN61829903
IC LocationDetailed Picture
3 Replace reset IC from DIODES Co to KEC
IC2304
3. Replace reset IC from DIODES Co. to KECa) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).
IC2304
65/60/55/49UH77**
Cautiona) The Reset IC is very sensitive, please prevent
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
Applied Model 65/60/55/49UH77**65/60/55/49UH87** Request
Basic Information
TV
Rework Guide
LH60/66 Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Platform M2 webOS
Company DIODES Apply model LH60/66..
Original p/n:
Rework Guide
Rework 1. Check work order information 2. Check actual IC on the board.
DIODES KEC
Circuit name IC2306 Part no Original p/n:EAN61829903
IC Location Detailed Picture
3 Replace reset IC from DIODES Co to KEC3. Replace reset IC from DIODES Co. to KECa) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).
IC2306 IC2306
Applied Model
55/49/43/32LH60/LH66**-N*/U*/S*/D*: Korea/North America/South America/Brazil55/49/43/32LH60**-C*/T*/P*: Hong Kong/Asia/MEA(Non Satellite)
Cautiona) The Reset IC is very sensitive, please prevent
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
: Hong Kong/Asia/MEA(Non-Satellite)Request
Basic Information Rework Guide
TVLH60 Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Chassis M2 webOS
Company DIODES Apply model LH60
Circuit name IC2306 Part no Original p/n:EAN61829903
Rework Guide
Rework 1. Check work order information 2. Check actual IC on the board.
DIODES KECEAN61829903
3 Replace reset IC from DIODES Co to KEC
IC LocationDetailed Picture
3. Replace reset IC from DIODES Co. to KECa) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).a) The Reset IC is very sensitive, please prevent
Applied Model 55/49/43/32LH60*V/Y/U/Z-T*: MEA / Asia (Satellite)
Caution) y , p p
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
IC2306IC2306
pp: MEA / Asia (Satellite) Request
Basic Information Rework Guide
TVLH57/59 Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Chassis M2 webOS/Smart
Company DIODES Apply model 55/49/43LH57/59..
Circuit name IC2306 Part no Original p/n:EAN61829903
Rework Guide
Rework 1. Check work order information 2. Check actual IC on the board.
DIODES KECEAN61829903
3 Replace reset IC from DIODES Co to KEC
IC Location Detailed Picture
3. Replace reset IC from DIODES Co. to KECa) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).IC2306 IC2306
Applied Model 49/43LH57/59**-Z* : EU/CIS
Cautiona) The Reset IC is very sensitive, please prevent
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
IC2306 IC2306
Applied Model 55/49/43LH59**-T* : Asia / MEARequest
Basic Information
TV
Rework Guide
LH56/57/58 Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Platform M2 Smart
Company DIODES Apply model 55/49/43LH5**
Original p/n:
Rework Guide
Rework 1. Check work order information 2. Check actual IC on the board.
DIODES KEC
Circuit name IC2306 Part no Original p/n:EAN61829903
IC Location Detailed Picture
3 Replace reset IC from DIODES Co to KEC3. Replace reset IC from DIODES Co. to KECa) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).IC2306
Applied Model
55/49/43LH57**-U/D/S/C/T* : : North America/South America/ Brazil /China / Hongkong / Asia / MEA
Cautiona) The Reset IC is very sensitive, please prevent
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
IC2306
Applied Model China / Hongkong / Asia / MEA55/49/43LH56**-S* : Brazil49/43LH58**-C* : China Request
Basic Information
TV
Rework Guide
LH58/6420 Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Platform M1A (DTV)
Company DIODES Apply model LH58/64
Circuit name IC401 Part no Original p/n:EAN61829903
Rework Guide
Rework 1. Check work order information 2. Check actual IC on the board.
DIODES KECEAN61829903
IC Location Detailed Picture
3 Replace reset IC from DIODES Co to KEC3. Replace reset IC from DIODES Co. to KECa) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).
) Th R t IC i iti l t
IC401
IC401
Applied Model 55/49/43LH58**-N*55/49/43LH6420 N*
Cautiona) The Reset IC is very sensitive, please prevent
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
IC401
55/49/43LH6420-NRequest
Basic Information
TV
Rework Guide
LF53/5400-UE Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Platform M1L (DTV)
Company DIODES Apply model 43/49LF5400-UE40LH5300-UA
Rework Guide
Rework 1. Check work order information 2. Check actual IC on the board.
DIODES KEC
Circuit name IC203 Part no Original p/n:EAN61829903
IC Location Detailed Picture3 Replace reset IC from DIODES Co to KEC3. Replace reset IC from DIODES Co. to KEC
a) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).a) The Reset IC is er sensiti e please pre ent
IC203
IC203
Applied ModelNorth America43/49LF5400-UE
Cautiona) The Reset IC is very sensitive, please prevent
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
pp40LH5300-UA Request
Basic Information
TV
Rework Guide
LH53*V-Z/54*VZ, VT Rework guide for Reset IC Replacement (DIODES Company)
Basic Information
IC Name Reset IC Platform M1AP
Company DIODES Apply model LH54/32LH53
Rework Guide
Rework 1. Check work order information 2. Check actual IC on the board.
DIODES KEC
Circuit name IC401 Part no Original p/n:EAN61829903
IC Location Detailed Picture3 Replace reset IC from DIODES Co to KEC
IC4013. Replace reset IC from DIODES Co. to KEC
a) KEC Part no. : EAN63491301b) When you are soldering, please prevent another
side defect, (don’t touch nearby parts)4. Perform function test to the board after rework.5. Place a Red Mark on S/N label of the Main board.
1. IC Level : Moisture Sensitivity Level (MSL) 3 Level (860F / 300C, 60%↓).a) The Reset IC is very sensitive, please preventIC401
Applied Model**LH54*V-Z***LH54*V-T*
Cautiona) The Reset IC is very sensitive, please prevent
ESD damage.b) Store any remaining ICs in vacuum packing.
2. To prevent ESD damage : Wear Wristlet, check Soldering Iron Ground.
pp32LH53*V-Z* Request