58
© Renault s.a.s. 2006 "The repair methods given by the manufacturer in this document are based on the technical specifications current when it was prepared. The methods may be modified as a result of changes introduced by the manufacturer in the production of the various component units and accessories from which his vehicles are constructed." All copyrights reserved by Renault. The reproduction or translation in part of whole of the present document, as well as the use of the spare parts reference numbering system, are prohibited without the prior written consent of Renault. 77 11 343 422 JULY 2005 Edition Anglaise Technical Note6029A JAX - JHX, and JH1 or JH3, and RENAULT - JRX, and RENAULT JA3 - JA5 - JH1 - JH3 - JR5 manual gearboxes TWINGO: X06X - KANGOO: XCXX - CLIO II: XBXX - CLIO III: XRXX - MODUS: XPXX - LOGAN: LS0X - MEGANE II: XMXX - LAGUNA II: XGXX Sub-section concerned: 21A This note cancels and replaces Technical Note 3661A and the MR for JH-JR gearboxes of March 2001 Edition 2

Caja Renault Logan

Embed Size (px)

Citation preview

Page 1: Caja Renault Logan

© Renault s.a.s. 2006

"The repair methods given by the manufacturer in this document are based on the technicalspecifications current when it was prepared.

The methods may be modified as a result of changes introduced by the manufacturer in theproduction of the various component units and accessories from which his vehicles areconstructed."

All copyrights reserved by Renault.

The reproduction or translation in part of whole of the present document, as well as the useof the spare parts reference numbering system, are prohibited without the prior writtenconsent of Renault.

77 11 343 422 JULY 2005 Edition Anglaise

Technical Note6029A

JAX - JHX, and JH1 or JH3, and RENAULT - JRX, and RENAULT

JA3 - JA5 - JH1 - JH3 - JR5 manual gearboxes

TWINGO: X06X - KANGOO: XCXX - CLIO II: XBXX - CLIO III: XRXX - MODUS: XPXX - LOGAN: LS0X - MEGANE II: XMXX - LAGUNA II: XGXX

Sub-section concerned: 21A

This note cancels and replaces Technical Note 3661A and the MR for JH-JR gearboxes of March 2001

Edition 2

Page 2: Caja Renault Logan

JA3 - JA5 - JH1 - JH3 - JR5 manualgearboxes

Contents

Page

JA3 - JA5 - JH1 - JH3 - JR5 manual gearboxes ContentsPage

21A MANUAL GEARBOX

Manual gearbox oil: Specifications 21A-1

Manual gearbox: Specifications 21A-2

Manual gearbox: Fault finding 21A-5

Reverse gear switch: Fault finding 21A-6

Manual gearbox: check 21A-7

Special tooling 21A-9

Manual gearbox: Parts and consumables for the repair work 21A-10

Manual gearbox: Precautions for repair 21A-11

Manual gearbox: List and location of components 21A-12

Mechanism housing:Removal 21A-18

Shafts and synchronisers:Removal 21A-21

Shafts and synchronisers: Adjustment 21A-24

Output shaft: Removal - Refitting 21A-27

Manual gearbox differential: Removal - Refitting 21A-31

Manual gearbox differential bearing: Removal - Refitting 21A-34

Pressure plate housing bearing: Removal - Refitting 21A-38

Clutch housing bearing: Removal - Refitting 21A-41

Selector fork shaft ring: Removal - Refitting 21A-45

Manual gearbox selector shaft: Removal - Refitting 21A-46

Shafts and synchronisers: Refitting 21A-47

Mechanism housing: Refitting 21A-51

21A MANUAL GEARBOX

Page 3: Caja Renault Logan

21A-1

MANUAL GEARBOXManual gearbox oil: Specifications

JHX – JRX, and JR5 – JAX, and JA5

21A

Filling

Fill up as far as the fuel filler cap opening.

Type Capacity (litres) Viscosity reference

JA3 - JH1 - JH3 2.8 TRJ 75W80

JA5 - JR5 2.5 TRJ 75W80

92081

Page 4: Caja Renault Logan

21A-2

MANUAL GEARBOXManual gearbox: Specifications

JRX, and JR5 – JAX, and JA5

21A GEAR RANGE: JA5 / JR5

Suffix First Second Third Fourth Fifth Reversegear

Finaldrive

Spee-dome-ter

Sequential gearbox

JA5-001 11/41 21/43 28/37 35/34 41/31 11/39 16/55 None

JR5 open differential gearbox

JR5-011 11/37 22/41 28/37 34/35 39/32 11/39 15/61 None

JR5 closed differential gearbox

JR5-102 11/41 21/43 28/37 35/34 41/31 11/39 15/56 None

JR5-103 11/41 21/43 28/37 35/34 41/31 11/39 15/58 None

JR5-104 11/41 21/43 28/39 31/34 37/33 11/39 15/61 None

JR5-108 11/41 21/43 28/37 35/34 42/31 11/39 15/56 None

JR5-110 11/41 21/43 28/37 35/34 41/31 11/39 15/58 None

JR5-113 11/41 21/43 28/37 35/34 41/31 11/39 16/57 None

JR5-116 11/41 21/43 28/37 35/34 41/31 11/39 16/55 21/19

JR5-118 11/41 21/43 28/37 35/34 42/31 11/39 15/56 None

JR5-119 11/41 21/43 28/37 35/34 41/31 11/39 15/56 None

JR5-120 11/41 21/43 28/37 35/34 41/31 11/39 17/56 None

JR5-123 11/41 21/43 28/37 35/34 41/31 11/39 16/57 None

JR5-124 11/41 21/43 28/37 35/34 41/31 11/39 16/55 None

JR5-125 11/41 21/43 28/37 35/34 39/32 11/39 14/63 None

JR5-126 11/37 22/41 28/37 35/34 42/31 11/39 15/58 21/19

JR5-128 11/41 21/43 28/37 35/34 41/31 11/39 16/55 None

JR5-129 11/41 21/43 28/37 35/34 39/32 11/39 14/63 None

JR5-131 11/41 21/43 28/37 35/34 42/31 11/39 15/61 None

JR5-144 11/37 22/41 28/37 35/34 42/31 11/39 15/58 21/18

JR5-145 11/41 22/43 28/37 35/34 41/31 11/39 16/55 21/18

JR5-150 11/41 21/43 28/37 35/34 42/31 11/39 15/58 None

Page 5: Caja Renault Logan

21A-3

MANUAL GEARBOXManual gearbox: Specifications

JAX, and JA3 – JHX

21A GEAR RANGE: JA3 / JH1 / JH3

Suffix First Second Third Fourth Fifth Reversegear

Finaldrive

Spee-dome-ter

Sequential gearbox

JA3-001 11/41 21/43 28/39 34/35 39/32 11/39 14/61 None

JH1 open differential gearbox

JH1 -004 11/37 22/41 28/37 34/35 39/32 11/39 14/59 21/19

JH1 -013 11/37 22/41 28/37 34/35 39/32 11/39 15/61 21/19

JH1 -014 11/37 22/41 28/37 30/29 39/32 11/39 15/58 21/19

JH1 -015 11/37 22/41 28/37 30/29 41/31 11/39 15/56 21/19

JH1 -016 11/37 22/41 28/37 34/35 39/32 11/39 14/59 None

JH1 -017 11/37 22/41 28/37 34/35 39/32 11/39 15/61 None

JH1 -018 11/37 22/41 28/37 30/29 41/31 11/39 15/56 21/19

JH1 -053 11/41 21/43 28/39 34/35 39/31 11/39 14/59 22/18

JH3 open differential gearbox

JH3-052 11/41 21/43 28/39 34/35 39/32 11/39 14/59 22/18

JH3-053 11/37 22/41 28/37 30/29 42/41 11/39 15/58 22/18

JH3-054 11/41 21/43 28/37 30/29 41/31 11/39 14/63 22/18

JH3-056 11/41 21/43 28/37 30/29 41/31 11/39 14/61 22/18

JR3 closed differential gearbox

JH3-105 11/41 21/43 28/39 31/34 37/33 11/39 14/59 None

JH3-106 11/41 21/43 28/39 34/35 39/32 11/39 14/63 None

JH3-128 11/41 21/43 28/39 34/35 39/32 11/39 14/61 None

JH3-129 11/41 21/43 28/39 31/34 37/33 11/39 15/61 None

JH3-131 11/41 21/43 28/39 31/34 37/33 11/39 15/58 None

JH3-132 11/37 22/41 28/37 30/29 42/41 11/39 15/58 None

JH3-137 11/41 21/43 28/39 31/34 37/33 11/39 14/59 None

JH3-141 11/37 22/41 28/37 30/29 42/41 11/39 15/58 None

JH3-142 11/41 21/43 28/39 31/34 37/33 11/39 15/61 None

JH3-143 11/41 21/43 28/39 31/34 37/33 11/39 15/61 None

JH3-144 11/41 21/43 28/39 31/34 37/33 11/39 15/61 None

Page 6: Caja Renault Logan

21A-4

MANUAL GEARBOXManual gearbox: Specifications

JAX, and JA3 – JHX

21A

JH3-145 11/37 22/41 28/37 30/29 42/31 11/39 16:57 None

JH3-150 11/37 22/41 28/37 30/29 42/41 11/39 15/58 None

JH3-154 11/41 21/43 28/39 31/34 37/33 11/39 16/61 None

JH3-155 11/41 21/43 28/39 31/34 37/33 11/39 15/58 None

JH3-172 11/41 21/43 28/39 31/34 37/33 11/39 15/61 None

Suffix First Second Third Fourth Fifth Reversegear

Finaldrive

Spee-dome-ter

Page 7: Caja Renault Logan

21A-5

MANUAL GEARBOXManual gearbox: Fault finding

JHX – JRX, and JR5 – JAX, and JA5

21AFault finding

The numbers indicate the order of priority for fault fin-ding.

Faults: (afterchecking theclutch)

Oil levelorgrade

Externalcontrol

Syn-chroni-sation

Gearing Selectorrod hub

Internalcontrol

Bea-rings

Engine-gear-boxsupport

Gear grinding 1 2 3 4

One or moregears cannot beselected

2 1 3 3 3 3

Jumping out ofgear

1 2 2 3

One or moregears jammed

2 1

Noisy 1 3 2

Page 8: Caja Renault Logan

21A-6

MANUAL GEARBOXReverse gear switch: Fault finding

JAX – JHX – JRX, and JR5

21A

Check the dual-function Reversing/Gear engagedswitch (1) using a multimeter and internal connections(2) (3) (4) .

114296 114545

Selected gear Continuity between 2and 3

Continuity between 2and 4

Reverse gear Yes No

Gears engaged No No

Neutral No Yes

Page 9: Caja Renault Logan

21A-7

MANUAL GEARBOXManual gearbox: check

JAX – JHX – JRX, and JR5

21AGearing:

When checking, make sure that you pay particularattention to the appearance of the teeth, especiallythat of the chamfers and claws.

Check that:

- the teeth (1) are neither broken nor chipped,

- the claws (2) are not broken, chipped or worn,

- the friction cone (3) shows no sign of being scrat-ched or blue stains,

- the inner wall (4) shows no sign of sticking or wear.

Selector rod hub:

Check:

- the selector rod slides into the hub without any pro-blem,

- that the cotters (5) are in good condition.

Synchroniser ring:

Check that the claw teeth (6) show no sign of wearor any fractures.

To check that the synchroniser ring is working cor-rectly, push the ring on the friction cone and rotate(7) : the ring should not turn. If it does turn, replacethe synchroniser ring.

100413 101896

100414

Page 10: Caja Renault Logan

21A-8

MANUAL GEARBOXManual gearbox: check

JAX – JHX – JRX, and JR5

21ABearing:

Make sure the bearings (8) are rotating properly.

If a bearing rotates unevenly or noisily, it must be re-placed.

100411

Page 11: Caja Renault Logan

21A-9

MANUAL GEARBOXSpecial tooling

JAX – JHX – JRX, and JR5

21ASpecial tooling required

Suffix Description Part no.

B.VI. 22-01 Bearing extractor tool 00 01 216 401

B.VI. 31-01 Set of drifts for roll pins 00 01 259 401

B.VI. 945 Differential oil seal fitting tool (JH open differential) 00 00 094 500

B.VI. 946 Stop ring on sunwheel fitting tool 00 00 094 600

B.VI. 949 Roll pin removal/refitting tool 00 00 094 900

B.VI. 1000-01 Fixed fifth gear extractor 00 00 100 001

B.VI. 1057 Differential locking tool 00 00 105 700

B.VI. 1058 Differential oil seal fitting tool (JR open differential) 00 00 105 800

B.VI. 1059 Differential bearing fitting tool 00 00 105 900

B.VI. 1161 Pre-adjustment washers and dial gauge support plate 00 00 116 100

B.VI. 1165 Output shaft bearing extraction tool 00 00 116 500

B.VI. 1170 Input shaft fifth hub extractor 00 00 117 000

B.VI. 1175 Fixed fifth gear fitting bolt 00 00 117 500

B.VI 1527 Backing plate for output shaft adjustment 00 00 152 700

B.VI. 1554 JC7 gearbox repair kit 00 00 155 400

B.VI. 1570 Tool for fitting locating balls 00 00 157 000

B.VI. 1576 Tool for fitting bearings on pressure plate housings 00 00 157 600

B.VI. 1581 Gearbox mounting 00 00 158 100

B.VI. 1601 Input shaft bearing fitting tool 00 00 160 100

B.VI. 1666 Differential oil seal fitting tool (JH/JR closed differential) 00 00 166 600

Page 12: Caja Renault Logan

21A-10

MANUAL GEARBOXManual gearbox: Parts and consumables for the repair work

JAX – JHX – JRX, and JR5

21AI - PARTS ALWAYS TO BE REPLACED

The following parts must be replaced with new ones af-ter being removed:

- lip seals,

- O-rings,

- lock rings,

- roll pins,

- input and output shaft bearing circlips,

- selector rod springs,

- hydraulic clutch slave cylinder.

II - CONSUMABLES

Component concerned Type of product Quantity Part no.

Immerse all parts Gearbox oil

Housing assembly Sealing resin 25 ml cartridge 77 11 237 640

Switch threading Sealing resin 25 ml cartridge 77 11 237 640

Fifth fixed gear Loctite FRENBLOC 24 cc bottle 77 01 394 071

Page 13: Caja Renault Logan

21A-11

MANUAL GEARBOXManual gearbox: Precautions for repair

JAX – JHX – JRX, and JR5

21AAll work on the gearbox must be carried out in cleanconditions.

Clean the gearbox carefully before opening it.

Operations on the gearbox must be carried out on aclean workbench or in a clean workshop.

During breaks, cover the open gearbox carefully to pre-vent foreign bodies from entering it.

Dismantle and handle the parts on a workbench with ashockproof coating (rubber or thick plastic).

Submerge all synchronising and rotating parts in a re-commended oil.

Observe the tightening torques.

Carry out the specified adjustments or settings with ca-re.

Be sure to properly refit parts in the same order and po-sition after removal.

Mark the selector rods against the hubs before they areremoved.

Make sure that the gearbox interior is kept free fromdust or contamination when refitting.

The seals must be completely clean, undamaged andfree from grease.

Tools used to refit seals must be clean and free fromany grease.

Note:

Respect the type of bearings fitted to the gearbox.There are three types of bearing for different gear-box suffixes (NTN - SNR - TIMKEN). They are notinterchangeable.

Page 14: Caja Renault Logan

21A-12

MANUAL GEARBOXManual gearbox: List and location of components

JAX, and JA3 – JHX

21A

(1) Oil deflector

(2) Bearing

(3) Output shaft

(4) First gear sprocket

(5) Synchroniser ring

(6) First/second selector rod hub

(7) Spring

(8) Roller

(9) Lock ring

(10) Splined washer

(11) Second gear sprocket

(12) Third gear sprocket

(13) Third-fourth selector rod hub

(14) Fourth gear sprocket

(15) Lock washer

(16) Retaining clip

(17) Bearing

(18) Fifth gear sprocket

(19) Output shaft bolt (70 Nm)

(20) Bearing guide

(21) Input shaft

(22) Retaining clip

(23) Bearing

(24) Lock washer

(25) Gear supporting ring

(26) Fifth gear sprocket

(27) Synchroniser ring

(28) Spring

(29) Selector rod hub

(30) Spring

(31) Friction cone

(32) Synchroniser ring

(33) Washer

(34) Input shaft nut (190 Nm)

101388

Page 15: Caja Renault Logan

21A-13

MANUAL GEARBOXManual gearbox: List and location of components

JAX, and JA3 – JHX

21A

(35) Differential seal

(36) Bearing

(37) Differential

(38) Speedometer sprocket (if fitted to the vehicle)

(39) Planet wheel

(40) Sunwheel

(41) Axis

(42) Shaft retaining spring

(43) Friction shell

(44) Selector shaft

(45) Gear shift catch

(46) Reverse gear brake fork and shaft

(47) Fifth gear fork and shaft

(48) Pin

(49) Reverse gear shaft

(50) Third/fourth gear fork and shaft

(51) Ring

(52) Lock shaft

(53) First/second gear fork and shaft

(54) Retaining ball cartridge

(55) Selector shaft bolt (20 Nm)

(56) Reverse gear fork shaft bolt (25 Nm)

(57) Pressure plate housing

(58) Filler plug

(59) Spacer

(60) Oil gutter channel

(61) Breather pipe

(62) Reverse gear sensor

(63) O-ring

(64) Fifth gear housing

(65) Gearbox bell housing bolt (25 Nm)

(66) Fifth gear housing bolt (25 Nm)

101393

101390

101391

Page 16: Caja Renault Logan

21A-14

MANUAL GEARBOXManual gearbox: List and location of components

JAX, and JA3 – JHX

21A

(67) Clutch housing

(68) Drain plug (25 Nm).

(69) Magnet

(70) Hydraulic bearing

(71) Bearing mounting bolt (21 Nm).

101392

Page 17: Caja Renault Logan

21A-15

MANUAL GEARBOXManual gearbox: List and location of components

JRX, and JR5 – JAX, and JA5

21A

(1) Oil deflector

(2) Bearing

(3) Output shaft

(4) First gear sprocket

(5) Synchroniser ring

(6) Spring

(7) First/second selector rod hub

(8) Synchroniser ring

(9) Gear supporting ring

(10) Second gear sprocket

(11) Splined washer

(12) Gear supporting ring

(13) Third-gear sprocket

(14) Synchroniser ring

(15) Third-fourth selector rod hub

(16) Synchroniser ring

(17) Gear supporting ring

(18) Fourth gear sprocket

(19) Adjustment washer

(20) Bearing

(21) Fifth gear sprocket

(22) Output shaft bolt (70 Nm)

(23) Bearing guide

(24) Input shaft

(25) Retaining clip

(26) Bearing

(27) Lock washer

(28) Gear supporting ring

(29) Fifth gear sprocket

(30) Synchroniser ring

(31) Spring

(32) Selector rod hub

(33) Spring

(34) Friction cone

(35) Synchroniser ring

(36) Washer

101389

Page 18: Caja Renault Logan

21A-16

MANUAL GEARBOXManual gearbox: List and location of components

JRX, and JR5 – JAX, and JA5

21A (37) Input shaft nut (190 Nm)

(38) Differential seal

(39) Bearing

(40) Differential

(41) Speedometer sprocket (if fitted to the vehicle)

(42) Planet wheel

(43) Sunwheel

(44) Axis

(45) Shaft retaining spring

(46) Friction shell

(47) Selector shaft

(48) Gear shift catch

(49) Reverse gear brake fork and shaft

(50) Fifth gear fork and shaft

(51) Pin

(52) Reverse gear shaft

(53) Third/fourth gear fork and shaft

(54) Ring

(55) Lock shaft

(56) First/second gear fork and shaft

(57) Retaining ball cartridge

(58) Selector shaft bolt (20 Nm)

(59) Reverse gear fork shaft bolt (25 Nm)

(60) Pressure plate housing

(61) Filler plug

(62) Spacer

(63) Oil gutter channel

(64) Breather pipe

(65) Reverse gear sensor

(66) O-ring

(67) Fifth gear housing

(68) Gearbox bell housing bolt (25 Nm)

(69) Fifth gear housing bolt (25 Nm)

101393

101390

101391

Page 19: Caja Renault Logan

21A-17

MANUAL GEARBOXManual gearbox: List and location of components

JRX, and JR5 – JAX, and JA5

21A

(70) Clutch housing

(71) Drain plug (25 Nm).

(72) Magnet

(73) Hydraulic bearing

(74) Bearing mounting bolt (21 Nm).

101392

Page 20: Caja Renault Logan

21A-18

MANUAL GEARBOXMechanism housing:Removal

JAX – JHX – JRX, and JR5

21A

REMOVAL

Fit the support plate (Bvi. 1581) (1) on a Desvilstand.

Remove:

- the clutch slave cylinder (2) ,

- the internal gear box bell housing bolts (3) ,

Remove the fifth gear housing along the horizontalaxis of the gearbox b (1) , because it comprisesa lubrication channel located in the bore of the pri-mary shaft.

Special tooling required

Bvi. 1581 JHX–JRX

Support for all types ofJ gearboxes.

Bvi. 31-01 JHX–JRX

Set of 3 roll pin drifts(5mm diameter rollpins).

Bvi. 1170 JHX–JRX

Extractor for 5th speedgear hub.

Bvi. 22-01 JHX–JRX

Extractor body withoutcover.

Bvi. 1000-01 JAX –JRX–JHX

5th fixed gear extrac-tor.

114295

114294

114296

Page 21: Caja Renault Logan

21A-19

MANUAL GEARBOXMechanism housing:Removal

JAX – JHX – JRX, and JR5

21A

Remove the mounting bolts (4) from the mounting ofthe reversing brake fork (where fitted).

Drive out the pin of the fifth gear fork using the (Bvi.31-01) .

Change into third gear using the gear lever.

Change into fifth gear by sliding the fifth gear forkalong its axis.

Remove:

- the output shaft bolt (5) ,

- the input shaft nut (6)

- the fifth gear fork and selector rod assembly (7)

Position the sliding assembly of the (Bvi. 1170) (8)

Rotate the tool so that the splines are opposite thoseof the input shaft hub.

Remove the fifth gear hub.

Remove the fifth fixed gear using the (Bvi. 22-01)(10) and the (Bvi. 1000-01) (9) .

Remove the gearbox bell housing bolts.

100408 114299

114300

Page 22: Caja Renault Logan

21A-20

MANUAL GEARBOXMechanism housing:Removal

JAX – JHX – JRX, and JR5

21A

Remove the reverse gear switch (11)

Remove the retaining pin of the reverse gear shaft(12) (if fitted).

Engage third gear.

Lift and remove the mechanism housing.

114741

Page 23: Caja Renault Logan

21A-21

MANUAL GEARBOXShafts and synchronisers:Removal

JAX – JHX – JRX

21A

CLOSED DIFFERENTIAL GEARBOX

Remove the fourth-gear sprocket (1) .

Remove the third/fourth gear "shaft/fork and selectorrod" assembly while gently lifting the primary shaft(2)

Remove the input shaft (3) .

Remove the output shaft (4) t.

Special tooling required

Bvi. 949 JHX–JRX

Tool for removing/refit-ting Mecanindus pinsfor selector fork shafts

101131

101130

101129

101128

Page 24: Caja Renault Logan

21A-22

MANUAL GEARBOXShafts and synchronisers:Removal

JAX – JHX – JRX

21A

Remove:

- the first/second gear shaft and fork (5) ,

- the fifth gear shaft (6) .

Remove the pin from the reverse gear assembly.

Remove:

- the reverse gear assembly (7)

- the differential (8) .

OPEN DIFFERENTIAL GEARBOX

Rotate the reverse gear shaft to the left (9) .

Remove the fifth gear shaft (10) .

Lift the input shaft slightly (11) .

Remove the reverse gear shaft (12) .

101127

101126

114739

114738

Page 25: Caja Renault Logan

21A-23

MANUAL GEARBOXShafts and synchronisers:Removal

JAX – JHX – JRX

21A

Remove the roll pin from the third/fourth gear usingthe (Bvi. 949) (13) .

Remove the third-forth gear "shaft and fork" assem-bly (14) .

Simultaneously remove the first/second gear "inputshaft - output shaft - fork"assembly (15) .

Do not forget to retrieve the interlock pins (16) .

114730

114744

114727

Page 26: Caja Renault Logan

21A-24

MANUAL GEARBOXShafts and synchronisers: Adjustment

JAX, and JA3 – JRX, and JR5 – JHX

21A

I - ADJUSTMENT OF THE PRE-TENSION OF THE TAPERED BEARINGS OF THE OUTPUT SHAFT

Only put the output shaft in the clutch housing to-gether with its bearings and the pretensioningwasher of the (Bvi. 1161) 1.60 mm in size (largeouter diameter

Position the mechanism housing.

Position and tighten to torque the gearbox bellhousing bolts ( 25 Nm )

Fit:

- the backplate (Bvi. 1527) (1) .

- the bolt (2) .

Fit the backplate of tool (Bvi. 1161) secured with twobolts and fit a dial gauge (3) .

Adjustment:

- Rotate the output shaft several times to fit the bea-rings.

- Set the dial gauge to zero.

Special tooling required

Bvi. 1161 JHX–JRX

Steel plate to attachDTI gauge and 0.6and 1.6 standardwrench.

Bvi. 1527 JHX–JRX

Plate for adjustingclearance of input andoutput shafts.

Tightening torquesm

the gearbox bell hou-sing bolts

25 Nm

gearbox bell housingbolts

25 Nm

Note:

This adjustment only needs to be carried outwhen replacing the housings or output shaft.

114316

114325

Page 27: Caja Renault Logan

21A-25

MANUAL GEARBOXShafts and synchronisers: Adjustment

JAX, and JA3 – JRX, and JR5 – JHX

21A- Pull the output shaft upwards b (1) using twoscrewdrivers as levers.

- Take a reading from the dial gauge.

- Repeat this operation three times.

- Calculate the average of the readings.

CALCULATE THE THICKNESS OF THE BEARINGS' PRETENSIONING WASHER

Prescribed value + value of the pre-setting washer +average of the readings on the dial gauge = value ofthe pretensioning washer.

example: (value in mm)

0.26 + 1.60 + 0.49 = 2.35

II - ADJUSTMENT OF THE PRE-TENSION OF THE TAPERED BEARINGS OF THE INPUT SHAFT

Only put the input shaft in the clutch housing to-gether with its bearings and the pre-setting washerof the (Bvi. 1161) 0.62 mm in size (small outer dia-meter

Position the mechanism housing.

Position and tighten to torque the gearbox bell hou-sing bolts ( 25 Nm )

Fit:

- the backplate (Bvi. 1527) (4) ,

- the lock washer (5) ,

- the gear supporting ring (6)

- the fully tightened nut (7) .

Note:

A set of washers with a total thickness rangingfrom 2.15 mm to 2.43 mm in gradations of 0.04mm is supplied as a spare part.

Note:

This adjustment only needs to be carried outwhen replacing the housings or input shaft.

114728

Page 28: Caja Renault Logan

21A-26

MANUAL GEARBOXShafts and synchronisers: Adjustment

JAX, and JA3 – JRX, and JR5 – JHX

21A

Fit the support plate of the (Bvi. 1161) secured withtwo bolts and fit a dial gauge with a magnetic stand.

Rotate the input shaft several times to fit the bea-rings.

Set the dial gauge to zero.

Pull the input shaft upwards using two screwdriversas levers.

Take a reading from the dial gauge.

Repeat three times and calculate the average ofthree readings.

CALCULATE THE THICKNESS OF THE BEARINGS' PRETENSIONING WASHER

Prescribed value + value of the pretensioningwasher + average of the readings on the dial gauge= value of the pretensioning washer.

Example: (value in mm)

0 + 0.62 + 0.48 = 1.10

114729

Note:

A set of washers with a total thickness rangingfrom 0.86 mm to 1.30 mm in gradations of 0.04mm is supplied as a spare part.

Page 29: Caja Renault Logan

21A-27

MANUAL GEARBOXOutput shaft: Removal - Refitting

JAX, and JA3 – JHX, and JH3

21AREMOVAL

Mount the output shaft in a vice fitted with jaws.

Remove:

- the fourth gear sprocket (1)

- the third/fourth gear selector rod hub (2) .

Remove:

- the lock ring (3) and fit a new one in every case,

- the splined washer (4) .

Remove:

- the third gear sprocket (5)

- the splined washer (6) .

Remove:

- the lock ring (7) and fit a new one in every case,

- the splined washer (8) .

114310

114315

114314

114313

Page 30: Caja Renault Logan

21A-28

MANUAL GEARBOXOutput shaft: Removal - Refitting

JAX, and JA3 – JHX, and JH3

21A

Remove:

- the second gear sprocket (9)

- the splined washer (10) .

Remove:

- the lock ring (11) and fit a new one in every case,

- the first/second gear selector rod hub (12) .

- the first gear sprocket (13) .

REFITTING

Proceed in the reverse order to remove.

Oil the synchroniser rings.

114312

114311

Note:

The lock rings must be systematically replaced.

100410

WARNING

Make sure that the notches on the double conesynchroniser are correctly positioned.

Page 31: Caja Renault Logan

21A-29

MANUAL GEARBOXOutput shaft: Removal - Refitting

JAX, and JA5 – JRX, and JR5

21AREMOVAL

REMOVAL OF THE GEAR ASSEMBLY

The rings supporting the second, third and fourthgears are fitted tightened. These shall be systemati-cally replaced during refitting.

Remove:

- the bearing,

- the setting washer,

- the fourth gear sprocket

- the third-fourth gear selector rod assembly,

- the "gear supporting ring, hub and third gear sproc-ket" assembly using an extractor and a press andlifting it from underneath the claw teeth of the thirdgear sprocket (1) .

Remove the "gear supporting ring, first and secondgear sprockets - hub - selector rod" assembly usingan extractor and a press and lifting it from under-neath the first gear sprocket (2) .

REFITTING

REFITTING THE GEAR ASSEMBLY

When reassembling, use a hot plate set at 150˚C .

114342

114343

Page 32: Caja Renault Logan

21A-30

MANUAL GEARBOXOutput shaft: Removal - Refitting

JAX, and JA5 – JRX, and JR5

21A

Place the new sprocket rings on the hot plate.

Heat the sprocket rings for 15 min , with the ther-mostat set at 150˚C .

Proceed in the reverse order to removal.

Refit the new sprocket rings using a tube with an in-ternal diameter of 33 mm until they are resting onthe hub.

Oil the synchroniser rings.

Make sure that the notches on the double cone syn-chroniser are correctly positioned.

114344

100410

Page 33: Caja Renault Logan

21A-31

MANUAL GEARBOXManual gearbox differential: Removal - Refitting

JHX – JRX, and JR5

21A

REMOVAL

JH type with open differential

Removal of lock ring:

- fit a shim underneath the crownwheel,

- push the housing using a press to release the lockring,

- remove the lock ring (1) .

Remove the differential using the sunwheel as asupport (2) .

JR type with open differential

Lock the differential using the (Bvi. 1057) .

Remove:

- the mounting nut,

- the differential using the sunwheel as a support.

Special tooling required

Bvi. 1057 JHX–JRX

Differential locking tool

Bvi. 946 JHX–JRX

Mandrel for fitting loc-king spring ring onsunwheel.

Tightening torquesm

differential mountingnut

130 Nm

114747

114761

114746

Page 34: Caja Renault Logan

21A-32

MANUAL GEARBOXManual gearbox differential: Removal - Refitting

JHX – JRX, and JR5

21AREFITTING

JH type with open differential

Refitting the lock ring:

- Fit a shim underneath the differential,

- Put the lock ring (3) on the shoulder (4) of the (Bvi.946) (5) ,

- Put the (Bvi. 946) (5) on the shoulder (4) ,

- Push the assembly using the press until the lockring falls into place.

JR type with open differential

Refit the differential in the housing.

Fit the (lightly oiled) bearing.

Fit the pretensioning washer

Fit the mounting nut and pre-tighten to 20 Nm

Rotate the differential several times to position thebearings.

Refit the (Bvi. 1057) .

Tighten to torque the differential mounting nut (130 Nm )

Remove the (Bvi. 1057) and rotate the differentialseveral times.

114756

114746

Page 35: Caja Renault Logan

21A-33

MANUAL GEARBOXManual gearbox differential: Removal - Refitting

JHX – JRX, and JR5

21AAdjusting the pretensioning of the bearings

The differential must rotate under a load of between:

- 5 Nm and 20 Nm if bearings are being reused,

- 16 Nm and 32 Nm if bearings are new. .

If the adjustment is not correct, determine the thic-kness of the shim, bearing in mind that pre-tensionincreases by 7 - 8 Nm with a reduction in thicknessof the setting washer of 0.05 mm and vice versa.

114763

Page 36: Caja Renault Logan

21A-34

MANUAL GEARBOXManual gearbox differential bearing: Removal - Refitting

JRX, and JR5 – JAX – JHX

21A

REMOVAL OF CLOSED DIFFERENTIAL GEARBOX BEARINGS

Remove the bearing races using a roll pin punch.

Remove the bearings using an extractor.

REFITTING OF CLOSED DIFFERENTIAL GEARBOX BEARINGS

Refit the bearing using a tube with a diameter of 40mm (1) .

Special tooling required

Bvi. 1554 JRX Tool kit for repairingJC7 gearboxes.

Bvi. 1059 JHX–JRX

Differential bearingbushes fitting kit

114292

114290

114291

Page 37: Caja Renault Logan

21A-35

MANUAL GEARBOXManual gearbox differential bearing: Removal - Refitting

JRX, and JR5 – JAX – JHX

21A

Refit the bearing races using tools C and F in the kit(Bvi. 1554) (2) .

REMOVAL OF OPEN DIFFERENTIAL GEARBOX BEARINGS

JH type on crownwheel side

Insert a small bar (3) in the casing and place it flat onthe bearing (4) .

Extract the bearing (4) using the press and a tube (5).

JH type on sunwheel side

Remove the bearing's lock ring (6) .

Withdraw the bearing (7) using the press and tube of50 mm (8) through the inside of the housing.

JR type on crownwheel side

Remove the bearing with an extractor.

Withdraw the bearing cups though the inside of thehousing using a roll pin punch.

114293

114751

114752

114762

Page 38: Caja Renault Logan

21A-36

MANUAL GEARBOXManual gearbox differential bearing: Removal - Refitting

JRX, and JR5 – JAX – JHX

21AREFITTING OPEN DIFFERENTIAL GEARBOX BEARINGS

JH type on crownwheel side

Refit the bearing using the press and the (Bvi. 1059)(9) using the external bearing bush as a support

JH type on sunwheel side

Refit the bearing using a tube with a diameter of 65mm (11) .

Refit a new lock ring on the bearing.

114757

Note:

The bearing's sealing race (10) must be facingthe side opposite the crownwheel

114753

Note:

The bearing's sealing race (12) must be facingthe side opposite the crownwheel

Page 39: Caja Renault Logan

21A-37

MANUAL GEARBOXManual gearbox differential bearing: Removal - Refitting

JRX, and JR5 – JAX – JHX

21AJR type on crownwheel side

Refit the bearing using the press and the (Bvi. 1059)(13) .

JR type on crownwheel side

Refit the large bearing's cup using the press and the(Bvi. 1059) (14) .

JR type on sunwheel side

Refit the small bearing's cup using the press and the(Bvi. 1059) (15) .

114758

114759

114760

Page 40: Caja Renault Logan

21A-38

MANUAL GEARBOXPressure plate housing bearing: Removal - Refitting

JAX, and JA3 – JHX

21A

REMOVAL

Remove the circlips b (1) .

Remove the bearing from inside the housing usingthe (Bvi. 1576) (1) .

REFITTING

Place the new circlips in their respective housings.

Fit the bearings using the (Bvi. 1576)

Knock the tool with the bearing in using a small ham-mer.

JH type open differential gearbox

the lock rings have various shapes:

- lock ring for the input shaft (2) .

- lock ring for the output shaft (3)

Special tooling required

Bvi. 1576 JHX– JAX

Pressure plate hou-sing bearing refittingmandrel.

114288

114767

Page 41: Caja Renault Logan

21A-39

MANUAL GEARBOXPressure plate housing bearing: Removal - Refitting

JAX, and JA5 – JRX, and JR5

21A

REMOVAL

I - REMOVAL OF THE BEARING ON THE INPUT SHAFT SIDE

Remove the circlips.

Remove the bearing from inside the housing usingthe (Bvi. 1576) at (1) .

II - REMOVAL OF THE BEARING CUP ON THE OUTPUT SHAFT SIDE

Remove the bearing cup on the output shaft sideusing a tube with a diameter of 55 mm .

REFITTING

I - REFIT THE BEARING ON THE INPUT SHAFT SIDE

Fit a new circlip.

Fit the bearing using the (Bvi. 1576)

Special tooling required

Bvi. 1576 JAX Pressure plate hou-sing bearing refittingmandrel.

101140

101141

Page 42: Caja Renault Logan

21A-40

MANUAL GEARBOXPressure plate housing bearing: Removal - Refitting

JAX, and JA5 – JRX, and JR5

21AII - REFITTING OF THE BEARING CUP ON THE OUTPUT SHAFT SIDE

Refit the bearing using a tube with a diameter of 60mm .

101139

Page 43: Caja Renault Logan

21A-41

MANUAL GEARBOXClutch housing bearing: Removal - Refitting

JAX, and JA3 – JHX

21A

REMOVAL

I - OUTPUT SHAFT BEARING

Cut the base of the plastic hollow tube located at thecentre of the bearing.

Position the (Bvi. 1165) (1) .

Remove the output shaft bearing from the clutchhousing.

II - INPUT SHAFT BEARING

Remove the bearing cup on the input shaft sideusing a press and a tube with a diameter of 38 mm(2) .

Special tooling required

Bvi. 1165 JHX For extracting outputshaft bearing onclutch/differential hou-sing.

Bvi. 1601 JHX Primary shaft oil sealfitting tool.

114304

114302

Page 44: Caja Renault Logan

21A-42

MANUAL GEARBOXClutch housing bearing: Removal - Refitting

JAX, and JA3 – JHX

21AREFITTING

I - OUTPUT SHAFT BEARING

Fit a new deflector.

Refit the output shaft bearing so that it is flush withthe inner surface of the clutch housing.

Crimp the output shaft bearing on the clutch housingusing a chisel.

II - INPUT SHAFT BEARING

Refit the bearing cup on the input shaft side using apress and the (Bvi. 1601) (3) .114301

114303

Page 45: Caja Renault Logan

21A-43

MANUAL GEARBOXClutch housing bearing: Removal - Refitting

JAX, and JA5 – JRX, and JR5

21A

REMOVAL

I - OUTPUT SHAFT BEARING CUP

Cut the base of the deflector plastic hollow needlelocated at the centre of the cup.

Remove the output shaft bearing cup from the clutchcasing using a slide hammer.

II - INPUT SHAFT BEARING

Remove by pressing the input shaft bearing using a∅∅∅∅ 38 mm (1) tube.

REFITTING

I - OUTPUT SHAFT BEARING CUP

Fit a new deflector.

Replace the output shaft bearing cup using a ∅∅∅∅ 55mm (2) tube.

Special tooling required

Bvi. 1601 JRX–JRX

Primary shaft oil sealfitting tool.

101137

114302

101138

Page 46: Caja Renault Logan

21A-44

MANUAL GEARBOXClutch housing bearing: Removal - Refitting

JAX, and JA5 – JRX, and JR5

21AII - INPUT SHAFT BEARING

Replace the input shaft bearing using tool (Bvi.1601) (3) .

114303

Page 47: Caja Renault Logan

21A-45

MANUAL GEARBOXSelector fork shaft ring: Removal - Refitting

JAX – JHX – JRX, and JR5

21AREMOVAL

Remove the rings with a slide hammer.

REFITTING

Refit the rings using a 14.5 mm tube down to thethrust bearing.

100400

100401

Page 48: Caja Renault Logan

21A-46

MANUAL GEARBOXManual gearbox selector shaft: Removal - Refitting

JAX – JHX – JRX, and JR5

21A

REMOVAL

Unpin the selector finger (1) .

Remove:

- the mounting bolts (2) ,

- the switch assembly.

REFITTING

Replace the O-ring. (3)

Proceed in the reverse order to removal.

Tighten to torque the switch mounting bolts ( 21Nm ) .

Tightening torquesm

switch mounting bolts 21 Nm

114305

114306

100407

Page 49: Caja Renault Logan

21A-47

MANUAL GEARBOXShafts and synchronisers: Refitting

JRX, and JR5 – JAX – JHX

21A

GEARBOX WITH ENCLOSED DIFFERENTIAL

Refit:

- the differential (1) ,

- the output shaft fitted with the "first-second" fork (2).

Refit:

- the input shaft, (3)

- the reverse gear assembly (4) .

Refit the inhibitor shafts (5) .

Special tooling required

Bvi. 949 JHX–JRX

Tool for removing/refit-ting Mecanindus pinsfor selector fork shafts

101132

101134

114308

Page 50: Caja Renault Logan

21A-48

MANUAL GEARBOXShafts and synchronisers: Refitting

JRX, and JR5 – JAX – JHX

21A

Refit:

- the fifth gear shaft (6) ,

- the third-fourth gear "selector rod - fork" assembly(7) ,

- turn the reverse gear shaft to position the fifth gearfork in the reverse gear shaft recess (8) .

Pin the reverse gear shaft (9) .

Engage third gear.

Insert:

- the springs (10) ,

- the rollers (11) .

Refit:

- the fourth gear sprocket (12) with its synchronisa-tion,

- the calibration washer,

- the output shaft bearing

101135

114289

101136

101131

Page 51: Caja Renault Logan

21A-49

MANUAL GEARBOXShafts and synchronisers: Refitting

JRX, and JR5 – JAX – JHX

21AGEARBOX WITH OPEN DIFFERENTIAL

Simultaneously position the input and output shaftsfitted with the first-second fork (13) (14) (15) .

Refit the inhibitor shafts (16) .

Gently lift the input and output shafts and fit the third-fourth fork.

Pin the fork using tool (Bvi. 949) (17) .

Fit the reverse gear shaft (18) while raising the inputshaft.

114744

114308

114730

114740

Page 52: Caja Renault Logan

21A-50

MANUAL GEARBOXShafts and synchronisers: Refitting

JRX, and JR5 – JAX – JHX

21A

Be sure to fit:

- the centring bushes (19) ,

- the magnet (20) .

Fit the timing rings and the conical bearings for gear-box JH3 and JR5.

114745

Page 53: Caja Renault Logan

21A-51

MANUAL GEARBOXMechanism housing: Refitting

JAX – JHX – JRX, and JR5

21AREFITTING

Fit the first-second, third-fourth and fifth gear shaftlocating ball cartridges into the gearbox housing.

Fit the springs and balls for gearbox not fitted with aball cartridge.

Engage the ball assemblies using the (Bvi. 1570)(27) .

Special tooling required

Bvi. 1570 JHX–JRX

Tools for fitting selec-tor fork shaft lockingsystems.

Bvi. 1175 JAX –JRX–JHX

Bolt for fitting 5thspeed fixed gear.

Bvi. 1666 JAX –JHX–JRX

Tool for fitting differen-tial seals.

Bvi. 945 JHX Mandrel for fittingsunwheel seal.

Bvi. 1058 JRX Mandrel for fittinggearbox output seal,differential side

Tightening torquesm

gearbox bell housingbolts

25 Nm

reverse gear switch 25 Nm

mounting bolt for thereverse gear fork brac-ket

25 Nm

output shaft bolt 80 Nm

input shaft nut 190 Nm

bolts mounting the fifthgear casing on the gear-box

25 Nm

bolts mounting theclutch slave cylinder onthe gearbox

21 Nm

114307

114748

Page 54: Caja Renault Logan

21A-52

MANUAL GEARBOXMechanism housing: Refitting

JAX – JHX – JRX, and JR5

21A

Engage third gear.

Check the positioning:

- of the centring dowels (1) ,

- of the magnet (2) .

Apply a bead of SEALING RESIN to the joint face.

Refit the gearbox housing, guiding the shift finger (3)into the fork of the third gear (4) .

Engage the locating ball for the fifth gear shaft forgearboxes not fitted with a locating ball cartridge.

Insert the reverse gear shaft retaining shaft (if fitted).

100406

114309

114743

114741

Page 55: Caja Renault Logan

21A-53

MANUAL GEARBOXMechanism housing: Refitting

JAX – JHX – JRX, and JR5

21A

Pretighten the gearbox bell housing bolts.

Turn the input shaft to ensure correct engagement ofthe bearings.

Tighten the gearbox bell housing bolts ( 25 Nm ) .

Apply three drops of LOCTITE FRENBLOC to thegrooves on the fifth gear fixed gear.

Fit the fifth gear fixed gear using the (Bvi. 1175) (5) .

Refit the reverse gear switch (6) .

Tighten to torque the reverse gear switch ( 25 Nm) .

Old type fifth gear assembly:

On the input shaft, refit the fifth gear module compri-sing:

- the support washer (7) (large face on gear side),

- the gear supporting ring (8) ,

- the fifth gear pinion fitted with its synchroniser ring(9) ,

- the fifth gear selector rod fitted with its spring (10) .

114298 114287

Page 56: Caja Renault Logan

21A-54

MANUAL GEARBOXMechanism housing: Refitting

JAX – JHX – JRX, and JR5

21ANew KYOWA fifth gear assembly

On the input shaft, refit the fifth gear module compri-sing:

- the support washer (7) (large face on gear side),

- the gear supporting ring (8) ,

- the fifth gear pinion (9) fitted with its synchronisa-tion ring (11) ,

- the fifth gear selector rod (12) fitted with two syn-chroniser levers (13) ,

- the fifth gear lock washer (14) .

Refit:

- the fifth gear selector rod - fork assembly (15) ,

- the synchronisation of the reverse gear (16) (onlyfor the old type fifth gear assembly),

- the fifth gear fork (17) (only for the old type fifthgear assembly).

Tighten to torque the mounting bolt for the rever-se gear fork bracket ( 25 Nm ) (18) (only for the oldtype fifth gear assembly).

Slide the fifth gear fork b (1) on its shaft to enga-ge fifth gear.

114642

Note:

The KYOWA fifth gear assembly may replace theold type fifth gear assembly.

An assembly kit is available as a replacementpart.

100409

Page 57: Caja Renault Logan

21A-55

MANUAL GEARBOXMechanism housing: Refitting

JAX – JHX – JRX, and JR5

21A

Fit:

- the output shaft bolt (19) ,

- the input shaft nut (20) .

Tighten to torque:

- the output shaft bolt ( 80 Nm ) (19) .

- the input shaft nut ( 190 Nm ) (20) .

Shift into neutral.

Pin the fifth gear fork (21) .

Fit a new O-ring to the fifth gear casing.

Refit the fifth gear casing on the gearbox (22) .

Tighten to torque the bolts mounting the fifth gearcasing on the gearbox ( 25 Nm ) (23) .

GEARBOX WITH ENCLOSED DIFFERENTIAL

Refit the new seals around the differential outputusing the (Bvi. 1666) (24)

100408 114295

21503

Page 58: Caja Renault Logan

21A-56

MANUAL GEARBOXMechanism housing: Refitting

JAX – JHX – JRX, and JR5

21AGEARBOX WITH OPEN DIFFERENTIAL

Refit a new seal at the differential output using the(Bvi. 945) (28) for JH gearboxes.

Refit a new seal at the differential output using the(Bvi. 1058) (29) and the cone of the (Bvi. 945) forJR gearboxes.

Refit the clutch slave cylinder (25) .

Tighten to torque the bolts mounting the clutchslave cylinder on the gearbox ( 21 Nm ) (26) .

114755

114764

114294