Canon EOS Rebel T3i Top Casing Replacement€¦ · Canon EOS Rebel T3i Top Casing Replacement This guide will help you replace the top casing. 作成者: Natalie Crock Canon EOS Rebel

Canon EOS Rebel T3i Top Casing ReplacementThis guide will help you replace the top casing.

作成者: Natalie Crock

Canon EOS Rebel T3i Top Casing Replac… 下書き： 2019-03-09ガイド ID: 50558 -

ã “ã ®æ–‡æ›¸ã ¯2020-02-08 12:24:37 AM (MST)ã «ä½œæˆ ã •ã‚Œã ¾ã —ã Ÿã€‚

© iFixit — CC BY-NC-SA jp.iFixit.com ãƒšãƒ¼ã‚¸14ã ®1

はじめにはじめに

Use this guide to replace the top casing on your Canon EOS Rebel T3i.

ツールツール:Phillips #000 Screwdriver (1)Spudger (1)Tweezers (1)




手順手順 1 — Battery

Locate the battery compartment onthe bottom of the camera.

手順手順 2

Hook your finger onto thecompartment door latch.

Open the battery compartment door.




手順手順 3

Remove the battery from thecompartment.

手順手順 4 — Front Casing

Remove the two 3 mm Phillips #000screws.

Some variations of this camera mayhave one 3mm and one 6mmscrews.

If the rubber eyepiece mount is stillon the camera, remove it beforeattempting to separate the casehalves.




手順手順 5

Remove the three 3 mm Phillips#000 screws.

Remove the single 6 mm Phillips#000 screw.

Some variation of this camera havetwo 3mm and two 6mm screws

手順手順 6

Peel back the grip tape with yourfingernail.

Depending on the age of thecamera, the grip tape will stick backin place with no need for extra glue.




手順手順 7

Remove the four 5 mm Phillips #000screws.

Some variation of this model mayhave three 5mm screws and one6mm

手順手順 8

Slide off the right side of thecamera.

Do not completely separate thebody yet. There are still wires thatmust be disconnected. If the body ispulled apart too quickly, it maycause damage.




手順手順 9

Lift off the USB cover.

Do not completely remove the backof the camera. There are still wiresthat must be disconnected.Removing the back too quickly maycause damage to wires.

When lifting the cover, the only thingresisting your tug is the plug coverstopper. Just pull, you'll be fine.

When replacing it, having the coverssnug on the plate will make it easierto push the whole cover on

手順手順 10

After separating the back, gently liftoff one side of the light blue wirewith the spudger until the connectoris totally removed.

You may feel a slight resistance asyou pull the top of the back cover off,it will click but that is fine.




手順手順 11

With the spudger, remove theorange ribbon cable leading to thecircuit board from the back of thecamera.

手順手順 12





手順手順 13

Remove the single 6 mm and two 3mm Phillips #000 screws.

手順手順 14

Use the spudger to lift the plasticunder the tripod mount.




手順手順 15

Lift the front cover off.

手順手順 16 — Top Casing

Remove the single 4 mm Phillips#000 screw located near the strapmount.




手順手順 17

On the opposite end of the camera,unscrew the screw next to the powerswitch using the same tool.

手順手順 18





手順手順 19

Disconnect this flat cable with aspudger




手順手順 20

Disconnect this tiny plug. Make sureto only pull on the white plastic. Youcan use a dull single-sided razorblade to pry the white plasticconnector from its base.

手順手順 21

Remove the single 11 mm Phillips#000 screw securing the dioptricadjustment knob.

When replacing, make sure you donot tighten the screw too much, asthe knob will be locked in position ifyou do.

Before replacing the knob/screw,make sure the grey plastic mount(screw hole area) is aligned with theouter case. If it is not, it means thelens and the knob are not lined up.With a flat screw driver, give thegrey plastic a few rotations, and itshould fall in place, and realignproperly.




To reassemble your device, follow these instructions in reverse order.

手順手順 22

Use the tweezers to disengage theyellow and red wires from thecamera body.

Some variations of this camera maynot have unplugable wires. Makesure to take note of which cablegoes where if you decide to removethe solder.

手順手順 23

Lift the top casing up and away from the camera.

I'm not sure what this is for, but make sure the black plastic bit (not a cable) goes into the whiteplastic bit, as shown on the picture.

Here is a view of the black plastic bit. It is on the underside of the top cover.




Documents

Canon EOS Rebel T3i Top Casing Replacement€¦ · Canon EOS Rebel T3i Top Casing Replacement This guide will help you replace the top casing. 作成者: Natalie Crock Canon EOS Rebel