Upload
michael-stuck
View
216
Download
0
Tags:
Embed Size (px)
DESCRIPTION
Instructions for motorcycle
Citation preview
Michael Stuck
OL # 263
Technical Communications
Professor Cari Ogden
December 27, 2010
Introduction
Description of Equipment
Materials & Equipment Required
Directions for changing the oil
Troubleshooting
This will be what we change the oil in today
The instructions in this pamphlet will help you
change the motor oil in a motorcycle. Following
these steps will ensure a hassle free way to
accomplish this task.
Read each step one at a time until all tasks are
complete. All tools and materials will be
addressed as you progress through the
pamphlet. Each time an oil change is required,
use this pamphlet to complete the task in 10 to
15 minutes.
This document should be used in any situation
that mechanical direction is needed.
Note!
A trained mechanic is a very useful in any
vehicle related task.
Caution!
Before beginning, ensure that the vehicle is
properly secured on level ground. Use proper
eye, ear, and skin protection when encountering
any type of chemicals.
Parts of the motorcycle that will be
used:
Dip Stick/Fill hole
(Located on right side top of engine)
Drain Plug
(Located on bottom of engine)
Oil Sight Glass
(Located on right hand side of engine)
Dip Stick/Fill
Hole
Sight Glass
Drain Plug
Before beginning the oil change gather the following material.
Motorcycle stand or equivalent to secure vehicle
Drain pan to catch old motor oil
3/8 drive ratchet
3/8 inch extension
17mm socket
1 oil funnel
1 qt. 10w-30 motor oil
(owners preferred motor oil may be used)
Stands
Ratchet,
Extension &
Socket
Oil
Drain Pan
Once all the material and parts are located let’s
begin:
1.) Secure motorcycle on level ground. Use
stands to prevent falling.
2.) Place drain pan under motorcycle.
3.) Remove drain plug with 17mm socket.
4.) Allow motor oil to drain until oil stops
draining.
5.) Reinstall drain plug and tighten with 17mm
socket.
Securing
Vehicle
Step 1
Draining oil into pan Steps 2, 3, 4 & 5
Continuing our oil change:
6.) Remove fill plug.
7.)Place oil funnel in fill plug hole.
8.) Poor 1 qt. 10w-30 motor oil into funnel/fill
hole.
Steps 6 & 7
Funnel
Fill Hole
Step 8
Continuing our oil change:
9.) Check oil sight window.
Note!
(Oil should be half way up the window. If not add additional oil up to half way mark.)
10.) Reinstall fill plug.
11.) Start engine for 1 to 2 minutes.
12.) Inspect oil sight window to ensure proper level one last time.
Note!
(Add oil if needed. Does not have to be exactly half way, Not too much though!)
Step 9 Add to Half Way Mark
Steps 10, 11, & 12 Proper oil level
Finishing up:
13.) Clean up materials and dispose of oil
waste.
14.) Enjoy until next oil change is required.
Frequently asked Questions.
Q) I do not have a level area to secure the
vehicle?
A) Level areas are best suited for this task.
Ensure vehicle will not fall over on the area
available.
Q) The drain plug is rounded off and not
loosening?
A) Try using a set of vise grips to clamp on
drain plug. This will eliminate the wrench
slipping and enable the plug to loosen.
Drain Plug
Level Area
Q: The oil has drained for many minutes and continues to drip?
A: There will always be some additional fluid that will be left over. The drain plug can be installed and new oil installed.
Q: The oil is past the very top of the sight glass?
A: If the oil level is overfilled, it should be drained and refilled. More oil than necessary could damage the engine.
Q: Where is the proper place to dispose of old motor oil?
A: Used motor oil may be dropped off at most Oreilly’s Auto Parts Stores and others for proper disposal.