22
2 TeSys contactors 5 Magnetic latching contactors Contactor type CR1 F150 CR1 F185 CR1 F265 Environment Rated insulation voltage (Ui) Conforming to IEC 60158-1, BS 775, 60947-4 V 1000 1000 1000 Conforming to VDE 0110 grC V 1500 1500 1500 Protective treatment Standard version “TH” Special version Ambient air temperature around the device Storage °C - 60…+ 80 For operation at Uc °C - 15…+ 70 Maximum operating altitude Without derating m 3000 Operating positions Without derating ± 5 ° Pole characteristics Number of poles 3 or 4 3 or 4 3 or 4 Rated operational current (Ie) (Ue y 440 V) In AC-3, θ y 40 °C A 150 185 265 In AC-1, θ y 40 °C A 250 275 350 In AC-4, θ y 40 °C A 138 170 245 Rated operational voltage (Ue) Up to V 1000 1000 1000 Frequency limits (sine wave) Of the opeational current Hz 25…200 25…200 25…200 Rated making capacity I rms A 1700 2100 2940 Rated breaking capacity I rms 220…440 V A 1500 1800 2450 500 V A 1200 1600 2200 660/690 V A 1100 1200 1700 1000 V A 450 600 800 Permissible short time rating from cold state, with no current flowing for previous 60 minutes at θ y 40 °C For 1 s A 1200 1500 2200 For 5 s A 1200 1500 2200 For 10 s A 1200 1500 2200 For 30 s A 700 920 1230 For 1 min A 600 740 950 For 3 min A 450 500 620 For 10 min A 350 400 480 Short-circuit protection by fuses θ y 440 V Motor circuit AC-3 (type aM) A 160 200 315 AC-1 circuit (type gG, BS 88) A 250 315 400 Average impedance per pole At lth and 50 Hz m0.45 0.36 0.32 Power dissipated per pole for the above operational currents AC-3 W 6 12 22 AC-1 W 18 26 39 Connection Number of conductors 1 1 1 Cable with lugs mm 2 120 150 240 Cable with connector mm 2 120 150 240 Number of bars 2 2 2 Bar c.s.a. mm 25 x 3 25 x 3 32 x 4 Bolt diameter Ø 8 Ø 8 Ø 10 Tightening torque N.m 18 18 35 Selection : pages 26001/3 to 26001/7 References : pages 26003/2 to 26007/3 Dimensions : pages 26008/2 to 26008/6 Schemes : pages 26008/8 and 26008/9 Selection : pages 26001/3 to 26001/7 References : pages 26003/2 to 26007/3 Dimensions : pages 26008/2 to 26008/6 Schemes : pages 26008/8 and 26008/9 Selection : pages 26001/3 to 26001/7 References : pages 26003/2 to 26007/3 Dimensions : pages 26008/2 to 26008/6 Schemes : pages 26008/8 and 26008/9 Selection : pages 26001/3 to 26001/7 References : pages 26003/2 to 26007/3 Dimensions : pages 26008/2 to 26008/6 Schemes : pages 26008/8 and 26008/9 Characteristics 5 26002-EN_Ver7.0.indd

Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

Embed Size (px)

Citation preview

Page 1: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

2

TeSys contactors 5 Magnetic latching contactors

Contactor type CR1 F150 CR1 F185 CR1 F265

EnvironmentRated insulation voltage (Ui) Conforming to IEC 60158-1,

BS 775, 60947-4V 1000 1000 1000

Conforming to VDE 0110 grC V 1500 1500 1500

Protective treatment Standard version “TH”Special version –

Ambient air temperaturearound the device

Storage °C - 60…+ 80For operation at Uc °C - 15…+ 70

Maximum operating altitude Without derating m 3000

Operating positions Without derating ± 5 °

Pole characteristicsNumber of poles 3 or 4 3 or 4 3 or 4

Rated operational current (Ie)(Ue y 440 V)

In AC-3, θ y 40 °C A 150 185 265In AC-1, θ y 40 °C A 250 275 350In AC-4, θ y 40 °C A 138 170 245

Rated operational voltage (Ue) Up to V 1000 1000 1000

Frequency limits(sine wave)

Of the opeational current Hz 25…200 25…200 25…200

Rated making capacity I rms A 1700 2100 2940

Rated breaking capacity I rms 220…440 V A 1500 1800 2450500 V A 1200 1600 2200660/690 V A 1100 1200 17001000 V A 450 600 800

Permissible short time ratingfrom cold state, with no current fl owing for previous 60 minutes at θ y 40 °C

For 1 s A 1200 1500 2200For 5 s A 1200 1500 2200For 10 s A 1200 1500 2200For 30 s A 700 920 1230For 1 min A 600 740 950For 3 min A 450 500 620For 10 min A 350 400 480

Short-circuit protection by fusesθ y 440 V

Motor circuit AC-3 (type aM) A 160 200 315AC-1 circuit (type gG, BS 88) A 250 315 400

Average impedance per pole At lth and 50 Hz mΩ 0.45 0.36 0.32

Power dissipated per polefor the above operational currents

AC-3 W 6 12 22AC-1 W 18 26 39

Connection Number of conductors 1 1 1Cable with lugs mm2 120 150 240Cable with connector mm2 120 150 240Number of bars 2 2 2Bar c.s.a. mm 25 x 3 25 x 3 32 x 4Bolt diameter Ø 8 Ø 8 Ø 10Tightening torque N.m 18 18 35

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Characteristics 5

26002-EN_Ver7.0.indd

Page 2: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

3

5

CR1 F400 CR1 F500 CR1 F630 CR1 BL CR1 BM CR1 BP CR1 BR

1000 1000 1000 1000 1000 1000 1000

1500 1500 1500 1500 1500 1500 1500

“TH” “TC”– “TH”

- 60…+ 80 - 60…+ 80- 15…+ 70 - 15…+ 60

3000 3000

± 5 ° in relation to normal vertical mounting plane ± 5 ° in relation to normal vertical mounting plane

3 or 4 3 or 4 3 or 4 1, 2, 3 or 4 1, 2, 3 or 4 1, 2, 3 or 4 1, 2, 3 or 4

400 500 630 750 1000 1500 1800500 700 1000 800 1250 2000 2750370 460 560 700 800 1250 15001000 1000 1000 1000 1000 1000 1000

25…200 25…200 25…200 50…60 50…60 50…60 50…60

4500 5000 6740 10 000 10 000 15 000 18 000

4000 5000 6300 10 000 10 000 15 000 18 0003500 4500 5400 9000 9000 12 000 15 0003000 3560 4600 8000 8000 9000 11 0001200 2500 3200 4000 4000 5000 60003600 4200 5050 9600 9600 12 000 15 0003600 4200 5050 9600 9600 12 000 15 0003600 4200 5050 7000 8000 9600 12 0002400 3200 4400 4800 5200 6400 80001700 2400 3400 3500 3800 5200 63001200 1500 2200 2100 2400 3600 44001000 1200 1600 1200 1800 2800 3600400 500 630 800 1200 800 x 2 (1) 1000 x 2 (1)500 800 1000 800 1200 1000 x 2 (1) 1200 x 2 (1)

0.28 0.18 0.12 0.18 0.18 0.13 0.09

45 45 48 88 180 290 36070 88 120 115 280 520 680

2 2 – – – – –150 240 – – – – –– – – – – – –2 2 2 2 2 3 430 x 5 40 x 5 60 x 5 50 x 5 80 x 5 100 x 5 100 x 10Ø 10 Ø 10 Ø 12 4 x Ø 8 4 x Ø 10 4 x Ø 10 4 x Ø 1035 35 58 21 35 35 35

(1) Paralleling of poles must be carried out only in accordance with the fuse manufacturer’s recommendations.

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

5

26002-EN_Ver7.0.indd

Page 3: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

4

TeSys contactors 5 Magnetic latching contactors

Contactor type CR1 F150 CR1 F185 CR1 F265

Control circuit characteristicsRated control circuit voltage (Uc)

a 50 or 60 Hz V 48…415a 400 Hz V 48…220c V 48…220c low consumption V 48…220

Control voltage limits a and c

Latching 0.85…1.1 UcUnlatching 0.85…1.1 Uc

Maximum operating rateat ambient temperature y 40 °C

In operating cycles per hour 120

Mechanical durability In millions of operating cycles 1Average consumption Latching 1-pole VA – – –

50/60 Hz 2-pole VA – – –3-pole VA 1100 1600 16504-pole VA 100 1600 1650

Unlatching 1-pole VA – – –2-pole VA – – –3-pole VA 7.3 8 94-pole VA 7.3 8 9

400 Hz and c Latching 1-pole VA – – –2-pole VA – – –3-pole VA 1260 1750 18004-pole VA 1260 1750 1800

Unlatching 1-pole VA – – –2-pole VA – – –3-pole VA 10 11 124-pole VA 10 11 12

c low consumption

Latching 3/4-pole W 500 500 500Unlatching 3/4-pole W 15 20 40

Average operating time at Uc (1)

Latching ms 35…40 35…40 45…50Unlatching ms 50…100 50…100 50…100

(1) The closing time is measured from the moment the closing coil is energised to initial contact of the main poles. The opening time is measured from the moment the opening coil is energised to the moment the main poles separate.

Nota : the arcing time depends on the circuit switched by the main poles. For 3-phase applications the arcing time is usually less than 10 ms. The load is isolated from the supply after a time equal to the sum of the opening time and the arcing time.

Auxiliary contact characteristicsType of contacts LAD N for contactors CR1 F

Conventional thermal current A 10

Rated insulation voltage(Ui)

Conforming to IEC 60947-5-1 V 690

Connection Flexible or solid conductor with or without cable end

mm2 1 x 1 min; 2 x 2.5 max

Operational power of contacts LAD N for contactors CR1 F

a.c. supply d.c. supplyElectrical durability (valid for up to 3600 operating cycles/hour) on an inductive load such as the coil of an electromagnet: making current (cos ϕ 0.7) = 10 times the power broken (cos ϕ 0.4).

Electrical durability (valid for up to 1200 operating cycles/hour) on an inductive load such as the coil of an electromagnet, without economy resistor, the time constant increasing with the load.

V 48 115 230 400 600 V 48 125 250 440

1 million operating cycles VA 120 280 560 960 1440 W 90 75 68 61Occasional making capacity VA 2600 7000 13 000 15 000 9000 W 700 400 260 220

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Characteristics 5

26002-EN_Ver7.0.indd

Page 4: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

5

5

CR1 F400 CR1 F500 CR1 F630 CR1 BL CR1 BM CR1 BP CR1 BR

48…415 110…50048…220 110…50048…220 110…50048…220 –0.85…1.1 Uc 0.85…1.1 Uc0.85…1.1 Uc 0.85…1.1 Uc120 120

1 1

– – – 650 650 650 650– – – 1100 1100 1100 11001450 1650 2100 1650 1650 1650 16501450 1650 2100 1850 1850 1850 1850– – – 110 110 110 110– – – 125 125 125 12512 9.5 8 165 165 165 16512 9.5 8 175 175 175 175– – – 600 600 600 600– – – 1000 1000 1000 10001600 1800 2300 1500 1500 1500 15001600 1800 2300 1700 1700 1700 1700– – – 100 100 100 100– – – 115 115 115 11516 13 11 150 150 150 15016 13 11 160 160 160 160500 550 620 – – – –70 60 45 – – – –40…75 40…80 40…80 100…150 100…150 100…150 100…15050…100 50…100 50…100 20…40 20…40 20…40 20…40

(1) The closing time is measured from the moment the closing coil is energised to initial contact of the main poles. The opening time is measured from the moment the opening coil is energised to the moment the main poles separate.

Nota : the arcing time depends on the circuit switched by the main poles. For 3-phase applications the arcing time is usually less than 10 ms. The load is isolated from the supply after a time equal to the sum of the opening time and the arcing time.

LAD N for contactors CR1 F ZC4 GM for contactors CR1 B

10 20

690 660

1 x 1 min; 2 x 2.5 max 2 min; 4 max

Operational power of contacts ZC4 GM for contactors CR1 B

a.c. supply d.c. supplyElectrical durability (valid for up to 2400 operating cycles/hour) on an inductive load such as the coil of an electromagnet: making current (cos ϕ 0.7) = 10 times the power broken (cos ϕ 0.4).

Electrical durability (valid for up to 1200 operating cycles/hour) on an inductive load such as the coil of an electromagnet, without economy resistor, the time constant increasing with the load.

V 110127

220 380 415440

500 V 110 120 440 500

1 million operating cycles VA 2000 4000 4000 4000 3500 W 250 250 230 200Occasional making capacity VA 14 000 23 000 35 000 45 000 35 000 W 1600 800 400 360

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

5

26002-EN_Ver7.0.indd

Page 5: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

2

TeSys contactors 5 Magnetic latching contactorsControl circuit: a.c. or d.c. supply

Maximum thermal current in category AC-140 °C

Rated operational current in category AC-3 (440 V max)

Number of poles

Instantaneous auxiliary contacts

Basic reference, to be completed by adding the voltage code (1)

Weight

A A kg250 150 3 – – CR1 F150pp 3.500

4 – – CR1 F1504pp 3.800275 185 3 – – CR1 F185pp 4.600

4 – – CR1 F1854pp 5.400350 265 3 – – CR1 F265pp 7.400

4 – – CR1 F2654pp 8.500500 400 3 – – CR1 F400pp 9.100

4 – – CR1 F4004pp 10.200700 500 3 – – CR1 F500pp 11.300

4 – – CR1 F5004pp 12.9001000 630 3 – – CR1 F630pp 18.600

4 – – CR1 F6304pp 21.500800 750 1 1 2 CR1 BL31p12 32.000

2 1 CR1 BL31p21 32.0003 – CR1 BL31p30 32.000

2 1 2 CR1 BL32p12 45.0002 1 CR1 BL32p21 45.0003 – CR1 BL32p30 45.000

3 1 2 CR1 BL33p12 58.0002 1 CR1 BL33p21 58.0003 – CR1 BL33p30 58.000

4 1 2 CR1 BL34p12 72.0002 1 CR1 BL34p21 72.0003 – CR1 BL34p30 72.000

1250 1000 1 1 2 CR1 BM31p12 31.0002 1 CR1 BM31p21 31.0003 – CR1 BM31p30 31.000

2 1 2 CR1 BM32p12 44.0002 1 CR1 BM32p21 44.0003 – CR1 BM32p30 44.000

3 1 2 CR1 BM33p12 57.0002 1 CR1 BM33p21 57.0003 – CR1 BM33p30 57.000

4 1 2 CR1 BM34p12 71.0002 1 CR1 BM34p21 71.0003 – CR1 BM34p30 71.000

2000 1500 1 1 2 CR1 BP31p12 41.0002 1 CR1 BP31p21 41.0003 – CR1 BP31p30 41.000

2 1 2 CR1 BP32p12 65.0002 1 CR1 BP32p21 65.0003 – CR1 BP32p30 65.000

3 1 2 CR1 BP33p12 94.0002 1 CR1 BP33p21 94.0003 – CR1 BP33p30 94.000

4 1 2 CR1 BP34p12 120.0002 1 CR1 BP34p21 120.0003 – CR1 BP34p30 120.000

2750 1800 1 1 2 CR1 BR31p12 52.0002 1 CR1 BR31p21 52.0003 – CR1 BR31p30 52.000

2 1 2 CR1 BR32p12 85.0002 1 CR1 BR32p21 85.0003 – CR1 BR32p30 85.000

3 1 2 CR1 BR33p12 129.0002 1 CR1 BR33p21 129.0003 – CR1 BR33p30 129.000

4 1 2 CR1 BR34p12 160.0002 1 CR1 BR34p21 160.0003 – CR1 BR34p30 160.000

(1) Standard control circuit voltages: see page opposite.

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26008/2 to 26002/5

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26008/2 to 26002/5

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26008/2 to 26002/5

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26008/2 to 26002/5

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

CR1 F1854

CR1 F500

CR1 BP33

5016

12_1

5016

13_1

5016

14_1

References 5

26003-EN_Ver7.0.indd

Page 6: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

3

TeSys contactors 5 Magnetic latching contactorsAccessories

Accessories for contactors CR1 FDescription Number of

contacts or shrouds

For use on Reference Weight

kgInstantaneous auxiliary contacts

(1) CR1 F LAD N (1) 0.050

Time delay auxiliary contacts

(1) CR1 F LAD p (1) 0.060

Contact blocks with protected terminals for 3-pole contactors (for mounting on contactors with closed arc chamber)

Set of 2 blocks CR1 F150 and CR1 F185

LA9 F103 0.300

Power terminal protection shrouds

Set of 6 shrouds for 3-pole contactors

CR1 F150 and CR1 F185

LA9 F702 0.250

CR1 F265 to CR1 F500

LA9 F703 0.250

CR1 F630 LA9 F704 0.250

Set of 8 shrouds for 4-pole contactors

CR1 F1504 and CR1 F1854

LA9 F707 0.300

CR1 F2654 to CR1 F5004

LA9 F708 0.300

CR1 F6304 LA9 F709 0.300

Description Application Reference

Mechanical interlock and power connections

For assembly of reversing contactors and changeover contactor pairs

See pages 26004/2 and 26004/3

Accessories for contactors CR1 BDescription Application Reference Weight

kgMechanical interlockwith mounting accessories (3)

For vertical assembly of reversing contactors and changeover contactor pairs

EZ2 LB0601 1.560

Kit containing 2 bar mounting brackets

For mounting on 120 or 150 mm centres

LA9 B103 1.620

(1) For maximum number per contactor and complete reference, see page 25010/3.(2) Standard control circuit voltages (for other voltages, please consult your Regional Sales

Offi ce):Volts 48 110 125 127 220 230 240 250 380 400 415 440 500For contactors CR1 Fa 50/60 Hz E7 F7 – G7 M7 M7 U7 – Q7 Q7 N7 – –a 400 Hz E7 F7 – G7 M7 M7 – – – – – – –c E7 F7 – G7 M7 M7 – – – – – – –c low consumption

EZ7 FZ7 – GZ7 MZ7 – – – – – – – –

For contactors CR1 Ba 50…400 Hz – F – G M M U – Q V N R Sc – FD GD – MD – UD UCD – – – RD SD(3) Positive mechanical interlocking between 2 vertically mounted contactors of identical or

different ratings. Connecting rods and cranks assembled on right-hand sides, crank pins on the pole side.Vertical fi xing centre distance between the two contactors: 600 mm.

LAD N

5013

77_1

LAD N

5013

77_1

LA9 F103

5016

16_1

LA9 F103

5016

16_1

LA9 F70p

5016

17_1

LA9 F70p

5016

17_1

EZ2 LB0601

5016

18_1

EZ2 LB0601

5016

18_1

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26008/2 to 26002/5

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26008/2 to 26002/5

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26008/2 to 26002/5

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26008/2 to 26002/5

Dimensions :pages 26008/2 to 26008/6

Schemes :pages 26008/8 and 26008/9

References 5

26003-EN_Ver7.0.indd

Page 7: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

2

TeSys contactors 5 Magnetic latching contactorsComponents for assembling reversing contactors and changeover contactor pairs CR1 FHorizontally or vertically mounted

Horizontally mountedMechanical interlocks Sets of power connections

Reversers assembled using 2 contactors of identical rating, type:CR1 F150CR1 F185CR1 F265CR1 F400CR1 F500CR1 F630

LA9 Fp970

Reversing contactorsLA9 Fp976

3 or 4-pole changeover contactor pairsLA9 Fp977 or LA9 Fp982

Vertically mountedMechanical interlocks

Reversers assembled using 2 contactors of identical rating, type:CR1 F150CR1 F185CR1 F265CR1 F400CR1 F500CR1 F630

LA9 FF4FLA9 FG4G

Assembly A LA9 FH4HLA9 FJ4JLA9 FK4KLA9 FL4L

Assembly C

Reversers assembled using 2 contactors of different ratings, type:CR1 F150CR1 F185CR1 F265CR1 F400CR1 F500CR1 F630

LA9 FG4F

Assembly A LA9 FH4FLA9 FJ4FLA9 FK4FLA9 FL4FLA9 FH4GLA9 FJ4GLA9 FK4GLA9 FL4G

Assembly B

LA9 FJ4HLA9 FK4HLA9 FL4HLA9 FK4JLA9 FL4JLA9 FK4K

Assembly C

Reversers assembled using 3 contactors of identical or different ratings

LA9 Fp4p4p

Warning: the contactor ratings must be in decreasing size from top to bottom.

A1

E1

A2

A1

A2

E1

12

34

56

12

34

56

L1 L2 L3

U V W

A1

E1

A2

A1

A2

E1

12

34

56

12

34

56

L1 L2 L3

U V W

A1

E1

A2

A1

A2

E1

12

34

56

34

56

78

1N

1/L3

1/L2

L2

12

L1

78

1/L1

2/L1

2/L2

2/L3 2N

L3 N

A1

E1

A2

A1

A2

E1

12

34

56

34

56

78

1N

1/L3

1/L2

L2

12

L1

78

1/L1

2/L1

2/L2

2/L3 2N

L3 N

F150F185F265F400F500F630

F150 F185 F265 F400 F500 F630

F185F265F400

F150

F500F630

CR1 F500

CR1 F265

CR1 F185

A

B

C

F150F185F265F400F500F630

F150 F185 F265 F400 F500 F630

F185F265F400

F150

F500F630

CR1 F500

CR1 F265

CR1 F185

A

B

C

Mounting 5

26004-EN_Ver7.0.indd

Page 8: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

3

TeSys contactors 5 Magnetic latching contactorsComponents for assembling reversing contactors and changeover contactor pairs CR1 F

Reversers assembled using 2 contactors of identical ratingContactor type Set of power connections Mechanical interlock

3-pole Reference

4-pole Reference

Weightkg

Kit reference Weightkg

For assembly of 3-pole reversing contactors for motor control (1)

Horizontally mountedCR1 F150 LA9 FF976 – 0.600 LA9 FF970 0.060CR1 F185 LA9 FG976 – 0.780 LA9 FG970 0.060CR1 F265 LA9 FH976 – 1.500 LA9 FJ970 0.140CR1 F400 LA9 FJ976 – 2.100 LA9 FJ970 0.140CR1 F500 LA9 FK976 – 2.350 LA9 FJ970 0.140CR1 F630 LA9 FL976 – 3.800 LA9 FL970 0.150Vertically mounted

CR1 F150 (2) – – LA9 FF4F 0.345CR1 F185 (2) – – LA9 FG4G 0.350CR1 F265 (2) – – LA9 FH4H 1.060CR1 F400 (2) – – LA9 FJ4J 1.200CR1 F500 (2) – – LA9 FK4K 1.200CR1 F630 (2) – – LA9 FL4L 1.220

For assembly of 4-pole changeover contactor pairs Horizontally mountedCR1 F1504 LA9 FF982 LA9 FF977 0.460 LA9 FF970 0.060CR1 F1854 LA9 FG982 LA9 FG977 0.610 LA9 FG970 0.060CR1 F2654 LA9 FH982 LA9 FH977 1.200 LA9 FJ970 0.140CR1 F4004 LA9 FJ982 LA9 FJ977 1.800 LA9 FJ970 0.140CR1 F5004 LA9 FK982 LA9 FK977 2.300 LA9 FJ970 0.140CR1 F6304 LA9 FL982 LA9 FL977 3.400 LA9 FL970 0.150Vertically mounted

CR1 F1504 (2) – – LA9 FF4F 0.345CR1 F1854 (2) – – LA9 FG4G 0.350CR1 F2654 (2) – – LA9 FH4H 1.060CR1 F4004 (2) – – LA9 FJ4J 1.200CR1 F5004 (2) – – LA9 FK4K 1.200CR1 F6304 (2) – – LA9 FL4L 1.220

Reversers assembled using 2 contactors of different ratingsContactor type Mechanical interlockAt bottom At top Kit reference Weight

kgFor assembly of 3 or 4-pole changeover contactor pairs Vertically mounted (3)

CR1 F150 or F1504 CR1 F185 or F1854 LA9 FG4F 0.350CR1 F265 or F2654 LA9 FH4F 0.870CR1 F400 or F4004 LA9 FJ4F 0.930CR1 F500 or F5004 LA9 FK4F 0.940CR1 F630 or F6304 LA9 FL4F 0.940

CR1 F185 or F1854 CR1 F265 or F2654 LA9 FH4G 0.860CR1 F400 or F4004 LA9 FJ4G 0.940CR1 F500 or F5004 LA9 FK4G 0.940CR1 F630 or F6304 LA9 FL4G 0.950

CR1 F265 or F2654 CR1 F400 or F4004 LA9 FJ4H 1.130CR1 F500 or F5004 LA9 FK4H 1.130CR1 F630 or F6304 LA9 FL4H 1.140

CR1 F400 or F4004 CR1 F500 or F5004 LA9 FK4J 1.200CR1 F630 or F6304 LA9 FL4J 1.210

CR1 F500 or F5004 CR1 F630 or F6304 LA9 FL4K 1.210For assembly of 3 or 4-pole reversing contactors Using 3 contactors (vertically mounted)

of identical or different ratingsMechanical interlockKit reference (4)

The contactor ratings must be in decreasing size from top to bottom.

LA9 Fp4p4p

(1) A 3-pole reversing contactor for motor control can be converted into a 3-pole changeover contactor pair by removing the upper connecting links.

(2) All power connections are to be made by the customer.(3) With identical or different number of poles. Power connections to be made by the customer.(4) Complete the reference by replacing the fi rst dot with the code for the upper contactor, the

second dot with the code for the middle contactor and the third dot with the code for the bottom contactor.

Contactors CR1 F150 CR1 F185 CR1 F265 CR1 F400 CR1 F500 CR1 F630Code F G H J K LExample: mechanical interlock for reversing contactor made up of 3 different contactors: CR1 F500 top, CR1 F26 middle and CR1 F185 bottom: LA9 FK4H4G.

Illustrations :page 26004/2

Dimensions :pages 26008/4 and 26008/5

Schemes :pages 26008/8 and 26008/9

Illustrations :page 26004/2

Dimensions :pages 26008/4 and 26008/5

Schemes :pages 26008/8 and 26008/9

Illustrations :page 26004/2

Dimensions :pages 26008/4 and 26008/5

Schemes :pages 26008/8 and 26008/9

Illustrations :page 26004/2

Dimensions :pages 26008/4 and 26008/5

Schemes :pages 26008/8 and 26008/9

References 5

26004-EN_Ver7.0.indd

Page 9: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

2

TeSys contactors 5 Magnetic latching contactorsCoils for contactors CR1 F

Standard coilsUsual voltages Resistance of winding

at θ = 20 °CReference Voltage

codeWeight

50…400 Hzor c

50 Hz, 60 Hz Latching Unlatching

V V Ω Ω kgFor contactors CR1 F150

48 – 1.98 230.8 LX0 FF005 E7 0.440110 – 9.35 1453 LX0 FF006 F7 0.440127 – 11.61 1788 LX0 FF007 G7 0.440208 – 23.50 4098 LX0 FF020 L7 0.440220/230 – 37.55 5139 LX0 FF008 M7 0.440– 240 45.16 6544 LX0 FF009 U7 0.440– 380/400 114.10 12 447 LX0 FF010 Q7 0.440– 415 139.50 16 717 LX0 FF011 N7 0.440

For contactors CR1 F18548 – 1,42 220 LX0 FG005 E7 0,560110 – 6.92 1339 LX0 FG006 F7 0.560127 – 8.45 1676 LX0 FG007 G7 0.560208 – 21.30 3169 LX0 FG020 L7 0.560220/230 – 26.27 4729 LX0 FG008 M7 0.560– 240 32.95 4729 LX0 FG009 U7 0.560– 380/400 82.29 11 885 LX0 FG010 Q7 0.560– 415 102.30 14 305 LX0 FG011 N7 0.560

For contactors CR1 F26548 – 1.34 183.4 LX0 FH005 E7 0.780110 – 6.90 1031 LX0 FH006 F7 0.780127 – 8.56 1325 LX0 FH007 G7 0.780208 – 20.20 2654 LX0 FH020 L7 0.780220/230 – 25.77 4090 LX0 FH008 M7 0.780– 240 33.03 5002 LX0 FH009 U7 0.780– 380/400 78.39 11 803 LX0 FH010 Q7 0.780– 415 102.9 15 006 LX0 FH011 N7 0.780

For contactors CR1 F40048 – 1.32 90.5 LX0 FJ005 E7 1.120110 – 8.09 813 LX0 FJ006 F7 1.120127 – 9.79 1027 LX0-FJ007 G7 1.120208 – 24.40 2643 LX0 FJ020 L7 1.120220/230 – 30.14 3309 LX0 FJ008 M7 1.120– 240 37.02 4074 LX0 FJ009 U7 1.120– 380/400 94.80 9380 LX0 FJ010 Q7 1.120– 415 121.10 11 763 LX0 FJ011 N7 1.120

For contactors CR1 F50048 – 1.57 166 LX0 FK005 E7 1.220110 – 7.53 916 LX0 FK006 F7 1.220127 – 9.56 1159 LX0 FK007 G7 1.220208 – 23.60 2981 LX0 FK020 L7 1.220220/230 – 28.81 3733 LX0 FK008 M7 1.220– 240 35.67 4595 LX0 FK009 U7 1.220– 380/400 89.56 10 570 LX0 FK010 Q7 1.220– 415 112.06 13 256 LX0 FK011 N7 1.220

For contactors CR1 F63048 – 0.87 204 LX0 FL005 E7 1.460110 – 5.20 1423 LX0 FL006 F7 1.460127 – 6.45 1830 LX0 FL007 G7 1.460208 – 20.20 2961 LX0 FL020 L7 1.460220/230 – 25.36 4603 LX0 FL008 M7 1.460– 240 25.36 5658 LX0 FL009 U7 1.460– 380/400 60.95 10 676 LX0 FL010 Q7 1.460– 415 77.97 13 003 LX0 FL011 N7 1.460

5014

70_1

LX0 FF009

5014

70_1

LX0 FF009

5014

71_1

LX0 FH009

5014

71_1

LX0 FH009

References 5

26005-EN_Ver8.0.indd

Page 10: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

3

TeSys contactors 5 Magnetic latching contactorsCoils for contactors CR1 F

Special coilsCoils with two windings with common point, allowing the use of two separate power sources for latching and unlatching. Coil voltages at 50 Hz, 60 Hz, 400 Hz or c

Resistance of winding at θ = 20 °C

Reference Voltage code

Weight

Latching Unlatching Latching UnlatchingV V Ω Ω kgFor contactors CR1 F150

220 24 29.5 39.5 LX0 FF224 MB7 0.440

For contactors CR1 F185220 24 26.5 19 LX0 FG224 MB7 0.560

For contactors CR1 F265220 24 26 29.5 LX0 FH224 MB7 0.780

For contactors CR1 F400220 24 30 23 LX0 FJ224 MB7 1.120

For contactors CR1 F500220 24 29 26 LX0 FK224 MB7 1.220

For contactors CR1 F630220 24 26 41 LX0 FL224 MB7 1.460

Coils with low inrush consumptionUsual voltagesc

Resistance of winding at θ = 20 °C

Reference Voltage code

Weight

Latching UnlatchingV Ω Ω kgFor contactors CR1 F150

48 4.56 140.56 LX0 FF055 EZ7 0.440110 22.37 706.44 LX0 FF056 FZ7 0.440127 35.54 1086.36 LX0 FF057 GZ7 0.440220 89.85 3342.51 LX0 FF058 MZ7 0.440

For contactors CR1 F18548 5.19 106.54 LX0 FG055 EZ7 0.570110 25.50 536.26 LX0 FG056 FZ7 0.570127 32.75 732.64 LX0 FG057 GZ7 0.570220 102.44 2378.62 LX0 FG058 MZ7 0.570

For contactors CR1 F26548 5.19 74.26 LX0 FH055 EZ7 0.800110 25 364.61 LX0 FH056 FZ7 0.800127 30.98 458.45 LX0 FH057 GZ7 0.800220 97.89 1344.46 LX0 FH058 MZ7 0.800

For contactors CR1 F40048 5.05 36.36 LX0 FJ055 EZ7 1.150110 25.39 171.49 LX0 FJ056 FZ7 1.150127 31.86 221.20 LX0 FJ057 GZ7 1.150220 98.19 648.79 LX0 FJ058 MZ7 1.150

For contactors CR1 F50048 4.42 41 LX0 FK055 EZ7 1.270110 22.74 193.36 LX0 FK056 FZ7 1.270127 28.25 313.60 LX0 FK057 GZ7 1.270220 85.12 918.68 LX0 FK058 MZ7 1.270

For contactors CR1 F63048 3.94 59.17 LX0 FL055 EZ7 1.500110 19.36 365.33 LX0 FL056 FZ7 1.500127 25.39 452.27 LX0 FL057 GZ7 1.500220 74.44 1071.43 LX0 FL058 MZ7 1.500

5014

72_1

LX0 FF030

5014

72_1

LX0 FF030

References (continued) 5

26005-EN_Ver8.0.indd

Page 11: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

2

TeSys contactors 5 Magnetic latching contactorsCoils for contactors CR1 B

Coils with “TC” treatment (associated accessories, see page opposite)Usual voltages Resistance

at θ = 20 °CReference Weight

c a50…400 Hz

V V Ω kgFor contactors CR1 Bp31

– 110…120 19.7 WB1 KB140 1.120110…125 – 25.2 WB1 KB134 1.120– 220…240 77.2 WB1 KB136 1.120220 – 94 WB1 KB139 1.120250 – 128 WB1 KB125 1.120– 380…400 197 WB1 KB126 1.120– 415…440 257 WB1 KB138 1.120

For contactors CR1 Bp32– 110 9.6 WB1 KB133 1.120110 120…127 11.4 WB1 KB121 1.120125 – 19.7 WB1 KB140 1.120– 220/230 32.5 WB1 KB124 1.120220 240 49.7 WB1 KB122 1.120250 – 77.2 WB1 KB136 1.120– 380…400 128 WB1 KB125 1.120– 415…440 160 WB1 KB137 1.120

For contactors CR1 Bp33– 110 7.2 WB1 KB123 1.120110 120…127 9.6 WB1 KB133 1.120125 – 11.4 WB1 KB121 1.120220 240 32.5 WB1 KB124 1.120250 – 61 WB1 KB135 1.120– 380…415 94 WB1 KB139 1.120– 440 128 WB1 KB125 1.120

For contactors CR1 Bp34– 110 5.8 WB1 KB132 1.120110 120…127 7.2 WB1 KB123 1.120125 – 11.4 WB1 KB121 1.120– 220/230 25.2 WB1 KB134 1.120– 240 32.5 WB1 KB124 1.120250 – 49.7 WB1 KB122 1.120– 380 77.2 WB1 KB136 1.120– 400…440 94 WB1 KB139 1.120

Coils with “TH” treatment (associated accessories, see page opposite)Add suffi x TH to the references selected above. Example: WB1 KB140TH.

5014

73_1

WB1 KBppp

5014

73_1

WB1 KBppp

References 5

26006-EN_Ver7.0.indd

Page 12: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

3

TeSys contactors 5 Magnetic latching contactorsCoils for contactors CR1 B

Accessories for use with coils (1)Coils(“TC” or “TH”)

Additional resistors (2) Automatic coil cut-out contact (3)

Rectifi er (4)

R1 Reference R2 Reference Nb Reference ReferenceΩ Ω

For contactors CR1 Bp31WB1 KB140 68 DR2 SC0068 47 DR2 SC0047 2 ZC4 GM2 or

ZC4 GM8 DR5 TE1U

WB1 KB134 68 DR2 SC0068 68 DR2 SC0068 2 ZC4 GM2 or ZC4 GM8

WB1 KB136 220 DR2 SC0220 180 DR2 SC0180 2 ZC4 GM2 or ZC4 GM8

DR5 TE1U

WB1 KB139 270 DR2 SC0270 220 DR2 SC0220 2 ZC4 GM2 or ZC4 GM8

WB1 KB125 330 DR2 SC0330 270 DR2 SC0270 3 ZC4 GM2 or ZC4 GM8

WB1 KB126 470 DR2 SC0470 470 DR2 SC0470 3 ZC4 GM2 or ZC4 GM8

DR5 TE1S

WB1 KB138 1000 DR2 SC1000 470 DR2 SC0470 3 ZC4 GM2 or ZC4 GM8

DR5 TE1S

For contactors CR1 Bp32WB1 KB133 10 DR2 SC0010 33 DR2 SC0033 1 PR4 FB0011 DR5 TE1U

WB1 KB121 47 DR2 SC0047 39 DR2 SC0039 1 PR4 FB0010 DR5 TE1U

WB1 KB140 100 DR2 SC0100 47 DR2 SC0047 1 PR4 FB0009 –

WB1 KB124 120 DR2 SC0120 120 DR2 SC0120 1 PR4 FB0007 DR5 TE1U

WB1 KB122 220 DR2 SC0220 150 DR2 SC0150 1 PR4 FB0007 DR5 TE1U

WB1 KB136 330 DR2 SC0330 220 DR2 SC0220 1 PR4 FB0006 –

WB1 KB125 470 DR2 SC0470 470 DR2 SC0470 1 PR4 FB0005 DR5 TE1S

WB1 KB137 680 DR2 SC0680 560 DR2 SC0560 1 PR4 FB0004 DR5 TE1S

For contactors CR1 Bp33WB1 KB123 39 DR2 SC0039 27 DR2 SC0027 1 PR4 FB0012 DR5 TE1U

WB1 KB133 47 DR2 SC0047 39 DR2 SC0039 1 PR4 FB0011 DR5 TE1U

WB1 KB121 56 DR2 SC0056 47 DR2 SC0047 1 PR4 FB0010 –

WB1 KB124 180 DR2-SC0180 120 DR2 SC0120 1 PR4 FB0008 DR5 TE1U

WB1 KB135 270 DR2 SC0270 270 DR2 SC0270 1 PR4 FB0006 –

WB1 KB139 470 DR2 SC0470 390 DR2 SC0390 1 PR4 FB0005 DR5 TE1S

WB1 KB125 680 DR2-SC0680 470 DR2 SC0470 1 PR4 FB0004 DR5 TE1S

For contactors CR1 Bp34WB1 KB132 33 DR2 SC0033 27 DR2 SC0027 1 PR4 FB0014

DR5 TE1U

WB1 KB123 47 DR2 SC0047 33 DR2 SC0033 1 PR4 FB0012 DR5 TE1U

WB1 KB121 56 DR2 SC0056 56 DR2 SC0056 1 PR4 FB0010 –

WB1 KB134 150 DR2 SC0150 120 DR2 SC0120 1 PR4 FB0008 DR5 TE1U

WB1 KB124 180 DR2-SC0180 150 DR2 SC0150 1 PR4 FB0007 DR5 TE1U

WB1 KB122 270 DR2 SC0270 220 DR2 SC0220 1 PR4 FB0007 –

WB1 KB136 390 DR2 SC0390 390 DR2 SC0390 1 PR4 FB0006 DR5 TE1S

WB1 KB139 560 DR2 SC0560 470 DR2 SC0470 1 PR4 FB0005 DR5 TE1S

(1) For connections, see page 26008/9.(2) Weight of resistors DR2 SCpppp : 0.030 kg.(3) Weight of automatic coil cut-out contacts: ZC4 GMp : 0.030 kg and PR4 FB00pp : 0.600 kg.(4) Weight of rectifi er DR5 TE1p : 0.100 kg. The rectifi er is for use on a.c. only.

5014

75_1

ZC4 GM2

5014

75_1

ZC4 GM2

5014

74_1

DR2 SC0220

5014

74_1

DR2 SC0220

5014

76_1

PR4 FB0014

5014

76_1

PR4 FB0014

5014

77_1

DR5 TE1U

5014

77_1

DR5 TE1U

References (continued) 5

26006-EN_Ver7.0.indd

Page 13: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

2

TeSys contactors 5 Magnetic latching contactorsAccessories and replacement parts for contactors CR1 F

ReferencesDescription For contactor Reference Weight

kgComplete sets of contacts for 3 or 4 poles (1)

3-pole CR1 F150 LA5 FF431 0.270

CR1 F185 LA5 FG431 0.350

CR1 F265 LA5 FH431 0.660

CR1 F400 LA5 F400803 0.660

CR1 F500 LA5 F500803 0.660

CR1 F630 LA5 F630803 0.660

4-pole CR1 F1504 LA5 FF441 0.360

CR1 F1854 LA5 FG441 0.465

CR1 F2654 LA5 FH441 0.880

CR1 F4004 LA5 F400804 0.465

CR1 F5004 LA5 F500804 0.465

CR1 F6304 LA5 F630804 0.465

Arc chambers 3-pole CR1 F150 LA5 F15050 0.490

CR1 F185 LA5 F18550 0.670

CR1 F265 LA5 F26550 0.920

CR1 F400 LA5 F40050 1.300

CR1 F500 LA5 F50050 1.850

CR1 F630 LA5 F63050 3.150

4-pole CR1 F1504 LA5 F150450 0.660

CR1 F1854 LA5 F185450 0.910

CR1 F2654 LA5 F265450 1.220

CR1 F4004 LA5 F400450 1.740

CR1 F5004 LA5 F500450 2.500

CR1 F6304 LA5 F630450 4.200

(1) Set containing the following (per pole): 2 fi xed contacts, 1 moving contact , 2 defl ectors, 1 back-plate, clamping screws and washers.

5014

78_1

LA5 FG431

5014

78_1

LA5 FG431

5014

79_1

LA5 F40050

5014

79_1

LA5 F40050

References 5

26007-EN_Ver7.0.indd

Page 14: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

3

TeSys contactors 5 Magnetic latching contactorsAccessories and replacement parts for contactors CR1 B

References (continued)Description For

contactorsNumber of sets required per pole

Unit reference of set

Weightkg

Sets of contacts(1 moving contact, 1 fi xed contact)

CR1 BL 1 PA1 LB80 0.420

CR1 BM 1 PA1 LB80 0.420

CR1 BP 2 PA1 LB80 0.420

CR1 BR 3 PA1 LB80 0.420

Description For contactors

Composition Reference Weightkg

Moving contact only(for one fi nger)

All ratings – PA1 LB75 0.220

Fixed contact only(for one fi nger)

All ratings – PA1 LB76 0.200

Blow-out horn only(for 1 fi nger)

All ratings – PA1 LB89 0.120

Arc chambers(for a single pole)

CR1 BL – PA1 LB50 3.700

CR1 BM – PA1 LB50 3.700

CR1 BP – PA1 PB50 6.200

CR1 BR – PA1 RB50 8.500

Auxiliary contact blocks

All ratings 1 N/O contact - normal

ZC4 GM1 0.030

All ratings 1 N/C contact - normal

ZC4 GM2 0.030

All ratings 1 N/O contact- gold fl ashed

ZC4 GM9 0.030

All ratings 1 N/C contact- gold fl ashed

ZC4 GM8 0.030

N/C polefor automatic cut-out coil

All ratings – PR4 FB00pp (1) 0.600

Set of moving and fi xed contacts for N/C pole

All ratings – PV1 FA80 0.035

Arc chamber for N/C pole

All ratings – PN1 FB50 0.220

Electromagnet All ratings – ET1 KB50 10.600

Description For contactors

No. of parts required

Reference Weightkg

Return springs for moving part of electromagnet

CR1 B(1 pole)

1 DV1 RT292 0.050

CR1 B(2, 3 or 4 poles)

2 DV1 RT292 0.050

N/O pole springs CR1 BL, BM or BP

1 per pole DV1 RC201 0.020

CR1 BR 1 per pole DV1 RC155 0.020

(1) Reference to be completed, see page 26006/3.

5014

80_1

PA1 LB80(PA1 LB76 + PA1 LB75)

5014

80_1

PA1 LB80(PA1 LB76 + PA1 LB75)

PA1 LB89

5014

82_1

PA1 LB89

5014

82_1

5014

83_1

PA1 LB50

5014

83_1

PA1 LB50

5014

81_1

ZC4 GM1

5014

81_1

ZC4 GM1

5014

84_1

PR4 FB004pp

5014

84_1

PR4 FB004pp

References (continued) 5

26007-EN_Ver7.0.indd

Page 15: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

2

TeSys contactors 5 Magnetic latching contactors CR1 F

CR1 F150 to F500Common side view CR1 F150, F185, F265 CR1 F400, F500

CR1 F150 F185 F265 CR1 F400 F5003P 4P 3P 4P 3P 4P 3P 4P 3P 4P

a 163.5 201.5 168.5 208.5 201.5 244.5 a 213 261 233 288b 170 170 174 174 203 203 G min. 66 66 66 66b1 137 137 137 137 145 145 b 206 206 238 238b2 301 301 305 305 370 370 b2 375 375 400 400c 171 171 181 181 213 213 c 219 219 232 232f 131 131 130 130 147 147 f 146 146 150 150G 106 143 111 151 142 190 G supplied 80 80 80 140G1 80 80 80 80 96 96 G max. 102 150 120 175J 106 106 106 106 106 106 G1 supplied 170 170 170 230J1 120 120 120 120 120 120 G1 min. 156 156 156 156L 107 107 113.5 113.5 141 141 G1 max. 192 240 210 265M 150 150 154 154 178 178 J 12 60 32 27P 40 40 40 40 48 48 L 145 145 146 146Q 26 26 29 29 39 34 M 181 181 208 208Q1 57.5 55.5 59.5 59.5 66.5 66.5 P 48 48 55 55S 20 20 20 20 25 25 Q 43 43 47 47S1 27 27 34 34 38 38 Q1 74 74 77 77Y 44 44 38.5 30.5 30.5 21.5 S 25 25 30 30Z 13.5 13.5 13.5 13.5 15.5 15.5f = minimum distance required for coil removal. f = minimum distance required for coil removal.X1: Minimum electrical clearance according to operational voltage and breaking capacity. X1: Minimum electrical clearance according to operational

voltage and breaking capacity.Voltage in V 200…500 660…1000 Voltage in V 200…500 660…1000

CR1 F150 10 15 CR1 F400 15 20CR1 F185 10 15 CR1 F500 15 20CR1 F265 10 15(1) Power terminal protection shroud.CR1 F630

CR1 F630 3P 4Pa 309 389G supplied 180 240G min. 100 150G max. 195 275J1 61 81Q 60 60Q1 89 89X1: Min. electrical clearance according to operational voltage and breaking capacity.Voltage in V X1

200…500 20690…1000 30(1) Power terminal protection shroud.(2) Minimum distance required for coil

removal.

J J1b1=

=

G1GZ

= =Y

3xØ6,5

Lc

(1)

=b

=b2

X1

X1

S1

Qa

P P Q1f

M

SF150 M8x25F185 M8x25F265 M10x35

J J1b1=

=

G1GZ

= =Y

3xØ6,5

Lc

(1)

=b

=b2

X1

X1

S1

Qa

P P Q1f

M

SF150 M8x25F185 M8x25F265 M10x35

Q1a

PQ Pf

M

44,5S6xM10x35

GG123,5 J

120

==

180

==

8xØ8,5

Q1a

PQ Pf

M

44,5S6xM10x35

GG123,5 J

120

==

180

==

8xØ8,5

155

=30

4=

(1)

197255

280

X1

464

72

X1

Q18080Q

264

181 (2)

64406xM12x45

a

180

==

J1G60,5

4xØ10,5

155

=30

4=

(1)

197255

280

X1

464

72

X1

Q18080Q

264

181 (2)

64406xM12x45

a

180

==

J1G60,5

4xØ10,5

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Dimensions 5

26008-EN_Ver7.0.indd

Page 16: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

3

TeSys contactors 5 Magnetic latching contactors CR1 F

CR1 F150…F265Panel mounted On pre-slotted mounting plate AM1 PA, PB, PC On rails DZ5 MB on 120 mm centres

CR1 F150 F185 F265 CR1 F150 F185 F265 CR1 F150 F185 F265c 3P 171 181 213 c 3P 171 181 213 c 3P 171 181 213

4P 171 181 213 4P 171 181 213 4P 171 181 213G 3P 80 80 96 G 3P 80 80 96 G 3P 80 80 96

4P 80 80 96 4P 80 80 96 4P 80 80 96J 3P 26.5 29 44.5

4P 45 49 68.5J1 3P 57 59.5 61.5

4P 75.5 79.5 85.5(1) Power terminal protection shroud.CR1 F150…F650

On 2 notched uprights AM1 ECppp

CR1 F150 F185 F265 F400 F500 F630c 3P 171 181 213 213 226 250

4P 171 181 213 213 226 250G (M6) 3P 80 80 96 – – –

4P 80 80 96 – – –G1 (Ø 8.5) 3P – – – 80 80 –

4P – – – 80 140 –G2 (Ø 10.5) 3P – – – – – 180

4P – – – – – 240(1) AF1 CDppp or AF1 VAppp.(2) This AM1 EC200 upright is required when G2 or G3 is greater than 700 mm (please consult your Regional Sales Offi ce).

3xØ6,5

c

J G=

J1

=

110

=

=

(1) 3xØ6,5

c

J G=

J1

=

110

=

=

(1)

c

AF1 EA6

110

G

c

AF1 EA6

110

G DZ5 MF5

c

G

110

120

15

DZ5 MF5

c

G

110

120

15

c 25

(1)

120

(2)

Ø10,5

AM1 EC200 AF1 CD081 + AF1 VC820

AM1 EC200

AF1 CD061+AF1 VA618

AF1 CD061 AF1 VA618M6

LA9 F100

AF1 CD101+AF1 VC10

AF1 CD081+AF1 VC820

Ø8,5M6

AM1 EC200

110

35

180

G

= =

G

AF1 VA618M6

G1

G2

G3

c 25

(1)

120

(2)

Ø10,5

AM1 EC200 AF1 CD081 + AF1 VC820

AM1 EC200

AF1 CD061+AF1 VA618

AF1 CD061 AF1 VA618M6

LA9 F100

AF1 CD101+AF1 VC10

AF1 CD081+AF1 VC820

Ø8,5M6

AM1 EC200

110

35

180

G

= =

G

AF1 VA618M6

G1

G2

G3

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Mounting 5

26008-EN_Ver7.0.indd

Page 17: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

4

TeSys contactors 5 Magnetic latching contactors CR1 F

Reversing contactors 2 x CR1 F150…F265 Reversing contactors 2 x CR1 F400…F630Horizontally mounted

2 x CR1 F150 F185 F265 2 x CR1 F400 F500 F630a 3P 345 357 425 a 3P 446 485 636

4P 422 437 521 4P 542 595 796b 3P 170 174 203 b 3P 206 238 304

4P 170 174 203 4P 206 238 304G1 3P 80 80 96 G 3P 80 80 180

4P 80 80 96 4P 80 140 240J 3P 71 78 109 G1 3P 170 170 –

4P 111 118 157 4P 170 230 –J1 3P 57 59.5 61.5 J 3P 157 156 139

4P 75.5 79.5 85.5 4P 157 156 139P1 3P 71 78 100 J1 3P 64.5 84.5 68.5

4P 71 78 100 4P 112.5 79.5 68.5J2 3P 67 66 –

4P 67 66 –J3 3P 19.5 39.5 –

4P 67.5 34.5 –P1 3P 107 112 137

4P 107 112 137(1) Except F630: 4 x Ø 10.5.(2) Except F630: 180.

110/

120

==

=

G1 J1

3xØ6,5

==

G1

=

J1 J

3xØ6,5

a

b

P1

110/

120

==

=

G1 J1

3xØ6,5

==

G1

=

J1 J

3xØ6,5

a

b

P1

G

G1 J3

120

(2)

==

180

==

8xØ8,5 (1)

b

GJ1 J1

J2

J

G1J3

8xØ8,5 (1) P1

a

G

G1 J3

120

(2)

==

180

==

8xØ8,5 (1)

b

GJ1 J1

J2

J

G1J3

8xØ8,5 (1) P1

a

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Mounting (continued) 5

26008-EN_Ver7.0.indd

Page 18: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

5

TeSys contactors 5 Magnetic latching contactors CR1 F

Reversing contactorsVertically mounted with mechanical interlock LA9 Fppp.2 contactors CR1 F of identical or different ratings (CR1 F150…F630), see pages 26004/2 and 26004/3.Assembly A Assembly B Assembly C

(1) Mechanical interlock shaft.(2) For assembly of contactors of different ratings only.(3) 3 x Ø 6.5 mm for CR1 F150…F265.(4) 3 x Ø 6.5 mm for CR1 F265.(5) Mechanical interlock guide bracket.(6) 4 x Ø 8.5 mm for CR1 F400, F500 or 4 x Ø 10.5 mm.Assembly type A B CLA9 F F4F G4F G4G H4F J4F K4F L4F H4G J4G K4G L4G H4H J4H K4H L4H J4J K4J L4J K4K L4K L4L

G1 3P – – – 96 80 80 180 96 80 80 180 96 80 80 180 80 80 180 80 180 1804P – – – 96 80 140 240 96 80 140 240 96 80 140 240 80 140 240 140 240 240

G2 3P – – – – – – – – – – – 96 96 96 96 80 80 80 80 80 1804P – – – – – – – – – – – 96 96 96 96 80 80 80 140 140 240

G3 3P 0 3 0 21 45 45 35 19 42 42 33 0 23 23 14 0 0 9 (7) 0 9 (7) 04P 0 4 0 27 26 26 17 23 22 22 13 0 0 0 9 (7) 0 0 9 (7) 0 9 (7) 0

G4 3P – – – – – – – – – – – 60 60 60 60 83 83 83 83 83 744P – – – – – – – – – – – 83 83 83 83 83 83 83 83 83 74

G5 3P – – – 60 83 83 74 60 83 83 74 60 83 83 74 83 83 74 83 74 744P – – – 83 83 83 74 83 83 83 74 83 83 83 74 83 83 74 83 74 74

H min. 200 210 220 240 250 270 310 250 250 270 310 250 260 280 330 260 280 325 300 345 380max. 310 300 310 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380 380

H1 min. 80 90 100 110 80 100 140 120 90 110 150 130 110 130 170 60 100 140 120 160 200max. 190 180 190 250 210 210 210 250 220 220 220 260 230 230 220 200 200 195 200 195 200

J1 3P 133 134 134 149.5 137 157 241 149.5 137 157 241 149.5 137 157 24 137 157 241 157 244 2414P 145 146 146 164.5 185 212 321 164.5 185 212 321 164.5 185 212 321 185 212 321 212 321 321

J2 3P 133 133 134 183 133 183 133 134 134 134 134 142.5 149.5 149.5 149.5 137 137 137 157 157 2414P 145 145 146 145 145 145 145 146 146 146 146 164.5 164.5 164.5 164.5 185 185 185 212 212 312

J3 3P 48.5 53 53 – – – – – – – – – – – – – – – – – –4P 67 73 73 – – – – – – – – – – – – – – – – – –

J4 3P 48.5 54 53 48.5 48.5 48.5 48.5 53 53 53 53 – – – – – – – – – –4P 67 69 73 67 67 67 67 73 73 73 73 – – – – – – – – – –

(7) In this case, G4 is greater than G5.

F33

0F

265

H1

120

F

400

F50

0F

630

180

F33

0F

265

120

F

400

F50

0F

630

180

J1G3(2)

(6)

G2G4

J2

12,59

= =

(4)

(6)

G1G512,5

H

(1)

(5)

(1)(5)

= =

F33

0F

265

180

H1

120

F

400

F50

0F

630

180

G1G512,5

J1G3(2)

80J4

(3)

= =

(6)

(4)

H

(1)

(1)

9

(5)

J2

120

120

H1

80J4

J2

J1G3(2)

= =

(3)

= =

(3)

80J3

H

(1)

(1)

F33

0F

265

H1

120

F

400

F50

0F

630

180

F33

0F

265

120

F

400

F50

0F

630

180

J1G3(2)

(6)

G2G4

J2

12,59

= =

(4)

(6)

G1G512,5

H

(1)

(5)

(1)(5)

= =

F33

0F

265

180

H1

120

F

400

F50

0F

630

180

G1G512,5

J1G3(2)

80J4

(3)

= =

(6)

(4)

H

(1)

(1)

9

(5)

J2

120

120

H1

80J4

J2

J1G3(2)

= =

(3)

= =

(3)

80J3

H

(1)

(1)

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :page 26004/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :page 26004/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :page 26004/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :page 26004/3

Schemes :pages 26008/8 and 26008/9

Mounting (continued) 5

26008-EN_Ver7.0.indd

Page 19: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

6

TeSys contactors 5 Magnetic latching contactors CR1 B

Contactors CR1 B Single-pole, 2-pole or 3-pole 4-poleCommon side view

CR1 BL CR1 BM CR1 BP CR1 BR1P 2P 3P 4P 1P 2P 3P 4P 1P 2P 3P 4P 1P 2P 3P 4P

a 50 50 50 50 63 63 63 63 100 100 100 100 125 125 125 125b 59 59 59 59 55 55 55 55 55 55 55 55 50 50 50 50c 16 16 16 16 20 20 20 20 20 20 20 20 25 25 25 25L 345 445 540 760 345 445 540 760 385 540 760 1065 445 635 885 1065M 285 385 480 – 285 385 480 – 325 480 700 – 385 575 825 –M1 – – – 308 – – – 308 – – – 455 – – – 455M2 – – – 392 – – – 392 – – – 550 – – – 550N 121 121 121 121 125 125 125 125 125 125 125 125 130 130 130 130P 100 100 100 100 100 100 100 100 150 150 150 150 195 195 195 195Q1 100 100 100 100 100 100 100 100 110 110 110 110 123 123 123 123R 122 122 122 122 157 157 157 157 173 173 173 173 173 173 173 173S 10 10 10 10 17 17 17 17 20 20 20 20 20 20 20 20T 30 30 30 30 30 30 30 30 60 60 60 60 60 60 60 60Ø 9 9 9 9 11 11 11 11 11 11 11 11 11 11 11 11Minimum electrical clearance

Values X1 and X2 are given for a breaking capacity of 10 In (3-phase a current). 3-phase a voltage CR1 BL CR1 BM CR1 BP CR1 BR

380-415-440 V X1 100 100 150 200X2 150 150 200 250

500 V X1 100 100 150 200X2 150 150 220 250

600 V X1 150 150 200 200X2 200 200 250 250

1000 V X1 200 200 200 250X2 250 250 250 300

Mechanical interlock for assembly of vertically mounted reversing contactorsEZ2 LB0601

a

TS Ø

T

260

R

290185N85

cb

c

365

a

TS Ø

T

260

R

290185N85

cb

c

365

44 P P Q1

30

15

30M

L

1535

0

44 P P Q1

30

15

30M

L

1535

0

350

P

30

15

30M1

L

P Q151

M2

15

350

P

30

15

30M1

L

P Q151

M2

15

X2

X1

X2

X1

A =

(E

–112

) 48

8

E =

600

A =

(E

–112

) 48

8

E =

600

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Dimensions 5

26008-EN_Ver7.0.indd

Page 20: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

7

TeSys contactors 5 Magnetic latching contactors CR1 B

Complete poleAdjustment of pick-up travel and pull-in travel

1 Moving circuit2 Coil3 Moving circuit4 Return spring

N/O pole adjustment

1 Fixed contact2 Moving contact3 Pull-in gap adjustment4 Adjustment of application force5 Pole spring

N/C automatic coil cut-out pole adjustment

1 Fixed contact2 Moving contact3 Opening gap adjustment4 Adjustment of application force5 Pole spring

a.c. or d.c. supply with economy resistor (and rectifi er on a)Contactor type CR1 BL CR1 BM CR1 BP CR1 BR

Electromagnet(EB5 KB50)

Pick-up travel (E) mm 30 30 30 30Pull-in travel (e) mm 10 10 10 10

Coil(WB1 KB)

Pull-in voltage V 0.75 Uc 0.75 Uc 0.75 Uc –Drop-out voltage V 0.3…0.5 Uc 0.3…0.5 Uc 0.3…0.5 Uc 0.3…0.5 Uc

N/O power pole(PA1)

Application force (F) to contact per pole

daN 30 30 30 (1) 30 (2)

N/C automatic coil cut-out pole(PR4)

Application force (F) daN 0.9 0.9 0.9 0.9Opening gap (b) with electromagnet closed

mm 3.5 ± 0.5 3.5 ± 0.5 3.5 ± 0.5 3.5 ± 0.5

(1) Each pole has 2 contacts: the force must be applied evenly to each of these contacts.(2) Each pole has 3 contacts: the force must be applied evenly to each of these contacts.

E

e

1

2

3

4

E

e

1

2

3

4

F

1

2

3

45

F

1

2

3

45

b

F

1

2

3

4

5

b

F

1

2

3

4

5

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Schemes :pages 26008/8 and 26008/9

5013

91_1

Adjustment characteristics 5

26008-EN_Ver7.0.indd

Page 21: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

8

TeSys contactors 5 Magnetic latching contactors CR1 F

Contactors CR1 F 3-pole 4-pole

Instantaneous auxiliary contacts (References : page 25010/3)1 N/O LAD N10 (1) 1 N/C LAD N01 (1) 1 N/O + 1 N/C LAD N11 2 N/O LAD N20 2 N/C LAD N02 2 N/O + 2 N/C LAD N22

1 N/O + 3 N/C LAD N13 4 N/O LAD N40 4 N/C LAD N04 2 N/O + 2 N/C of which 1 N/O + 1 N/C make before break LAD C22

3 N/O + 1 N/C LAD N31

(1) Items in brackets refer to blocks mounted on right-hand side of contactor.Instantaneous auxiliary contacts conforming to standard EN 50012 (References: page 25010/3)

1 N/O +1 N/CLAD N11P

1 N/O +1 N/CLAD N11G

2 N/O + 2 N/CLAD N22P

2 N/O + 2 N/CLAD N22G

Front mounting add-on contact blocks - Dust and damp protected instantaneous auxiliary contacts (References : page 25010/3)2 N/O (24-50 V)LA1 DX20

2 N/O (5-24 V)LA1 DY20

2 N/O protected (24-50 V) 2 N/O standardLA1 DZ40

2 N/O protected (24-50 V) + 1 N/O + 1 N/C standardLA1 DZ31

Time delay auxiliary contacts (References : page 25010/3)On-delay 1 N/O + 1 N/C LAD Tp Off-delay 1 N/O + 1 N/C LAD Rp On-delay 1 N/C + 1 N/O break before make

LAD Sp

3-pole reversing contactors 2 x CR1 F150…F630 4-pole reversing contactors 2 x CR1 F1504…F6304

Vertically mounted contactors using 2 contactors of identical or different ratings

A1

A2

E1

1/L1

T1/

2

3/L2

T2/

4

5/L3

T3/

6

A1

A2

E1

1/L1

T1/

2

3/L2

T2/

4

5/L3

T3/

6

A1

A2

E1

1/L1

T1/

2

3/L2

T2/

4

5/L3

T3/

6

7/L4

T4/

8

A1

A2

E1

1/L1

T1/

2

3/L2

T2/

4

5/L3

T3/

6

7/L4

T4/

8

43 N

O44

43/N

O

(94)

(93)

43 N

O44

43/N

O

(94)

(93) 42

41/N

C

(91)

(92)

4241

/NC

(91)

(92)

53/N

O54 62

61/N

C

53/N

O54 62

61/N

C

63/N

O64

53/N

O54

63/N

O64

53/N

O54 52

51/N

C

6261

/NC

5251

/NC

6261

/NC

7271

/NC

6261

/NC

83/N

O84

53/N

O54 72

71/N

C

6261

/NC

83/N

O84

53/N

O54

7271

/NC

6261

/NC

53/N

O54 82

81/N

C

7271

/NC

6261

/NC

53/N

O54 82

81/N

C

83/N

O84

73/N

O74

63/N

O64

53/N

O54

83/N

O84

73/N

O74

63/N

O64

53/N

O54 52

51/N

C

6261

/NC

7271

/NC

8281

/NC

5251

/NC

6261

/NC

7271

/NC

8281

/NC

53/N

O54

61/N

C62

87/N

O88

75/N

C76

53/N

O54

61/N

C62

87/N

O88

75/N

C76 62

61/N

C

83/N

O84

73/N

O74

53/N

O54 62

61/N

C

83/N

O84

73/N

O74

53/N

O54

2221

/NC

13/N

O14 22

21/N

C

13/N

O14 32

31/N

C

43/N

O4432

31/N

C

43/N

O44 22

21/N

C

3231

/NC

13/N

O14

43/N

O4422

21/N

C

3231

/NC

13/N

O14

43/N

O44 32

31/N

C

4241

/NC

63/N

O64

53/N

O5432

31/N

C

4241

/NC

63/N

O64

53/N

O54

53/N

O54

63/N

O64

53/N

O54

63/N

O64

53/N

O54

63/N

O64

53/N

O54

63/N

O64

53/N

O54

83/N

O84

63/N

O64

73/N

O74

53/N

O54

83/N

O84

63/N

O64

73/N

O74 62

61/N

C

53/N

O54

83/N

O84

73/N

O7462

61/N

C

53/N

O54

83/N

O84

73/N

O74

55/N

C56

67/N

O68

55/N

C56

67/N

O68 66

65/N

C

57/N

O58 66

65/N

C

57/N

O58

67/N

O68

55/N

C56

67/N

O68

55/N

C56

A1

A2

E1

A1

A2

E1

12

34

56

L1 L2 L3

12

34

56

U V W

Horizontally mounted A1

A2

E1

A1

A2

E1

12

34

56

L1 L2 L3

12

34

56

U V W

Horizontally mounted A1

A2

E1

A1

A2

E1

12

34

56

1N

1/L3

1/L2

12

34

56

L1 L2 L3

78

1/L1

2/L1

2/L2

2/L3

78

N2N

A1

A2

E1

A1

A2

E1

12

34

56

1N

1/L3

1/L2

12

34

56

L1 L2 L3

78

1/L1

2/L1

2/L2

2/L3

78

N2N

A1

A2

E1

12

34

1/L1

1/L2

12

34

2/L1

2/L2

56

1/L3

56

2/L3

A1

A2

E1

L3L2L1

A1

A2

E1

12

34

1/L1

1/L2

12

34

2/L1

2/L2

56

1/L3

56

2/L3

A1

A2

E1

L3L2L1

A1

A2

E1

12

34

78

1/L1

1/L2 1N

12

34

78

2/L1

2/L2

2N

56

1/L3

56

2/L3

A1

A2

E1

L3L2L1

N

A1

A2

E1

12

34

78

1/L1

1/L2 1N

12

34

78

2/L1

2/L2

2N

56

1/L3

56

2/L3

A1

A2

E1

L3L2L1

N

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 and 26008/5

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 and 26008/5

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 and 26008/5

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Dimensions :pages 26008/2 and 26008/5

Schemes 5

26008-EN_Ver7.0.indd

Page 22: Characteristics TeSys contactors Magnetic latching contactorskatalog.schneider-electric.cz/dsmapp/data/pdf/CZ/TL1/Stykac_CRF1.pdf · Magnetic latching contactors Contactor type CR1

9

TeSys contactors 5 Magnetic latching contactors

Contactors CR1 BCR1 Bp31p12 CR1 Bp31p21 CR1 Bp31p30

CR1 Bp32p12 CR1 Bp32p21 CR1 Bp32p30

CR1 Bp33p12 CR1 Bp33p21 CR1 Bp33p30

CR1 Bp34p12 CR1 Bp34p21 CR1 Bp34p30

Wiring schemesContactors CR1 F and CR1 B with thermal overload relay

Contactors CR1 F

Connectors CR1 B

(1) automatic coil cut-out contact ZC4 GM or PR4 FB00ppS1: latching pushbuttonS2: unlatching pushbutton

Coils for contactors CR1 FPushbutton control Scheme of internal circuit

Switch control

Warning: terminal A2 is common to both windings in all cases.

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

A1

A2

2 4 6

L1 L2 L3

1 3 5

– KM1

U W

M 3 c

V

1 3 5

2 4 6

– F1

2 4 6

L1 L2 L3

1 3 5

– KM1

U W

M 3 c

V

1 3 5

2 4 6

– F1

1314

– KM1

9596

– F1

1314

– S1

9798

1314

– S2

A1

E1

A2

– KM1

– KM1:1

– KM1:5

1314

– KM1

9596

– F1

1314

– S1

9798

1314

– S2

A1

E1

A2

– KM1

– KM1:1

– KM1:5

9695

1314

– S1

1314

– KM1

A1

A2

R1

9798

R2

– F1

21

– KM1

KM1:

1

KM1:

5

(1)

2122

– S2

9695

1314

– S1

1314

– KM1

A1

A2

R1

9798

R2

– F1

21

– KM1

KM1:

1

KM1:

5

(1)

2122

– S2

A1

A2

CR1

E1

a(–)/c a(+)/c

A1

A2

CR1

E1

a(–)/c a(+)/c

Ø A1

Ø E1

Ø A2

Unlatching winding

Ø A1

Ø E1

Ø A2

Unlatching windingA

1A

2

CR1

E1

CR1

a(–)/c a(+)/c

A1

A2

CR1

E1

CR1

a(–)/c a(+)/c

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Dimensions :page 26008/6

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Dimensions :page 26008/6

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Dimensions :page 26008/6

Selection :pages 26001/3 to 26001/7

Characteristics :pages 26002/2 to 26002/5

References :pages 26003/2 to 26007/3

Dimensions :page 26008/6

Start

Stop

Start/Stop

Latching winding

Schemes (continued) 5

26008-EN_Ver7.0.indd