Configurare SIAE

7/27/2019 Configurare SIAE

http://slidepdf.com/reader/full/configurare-siae 1/33



AL Compact PDH Radio

3 LAN

LCT DescriptionPART 1

Connecting to LCT – Equipment -

Connexion to LCT – Software –

PC: USB Cable

Click on Connect



Login to equipment

Equipment @ IP

SYSTEM

SIAEMICR

To avoid each time to

enter Password

Connexion

Connexion from one or more IP@

from a file (See P45)

Clique on OK to accede tothe LCT software



PART 2

LCT Windows

Description of the Menu Bar

From Left to Write:Connect / DisconnectConnect - Contains the commands to activate the connection with every equipment preseinto the network.Disconnect - Allows deactivating the connection.

Login

Contains the commands to activate the login with one or more remote equipment pres

into the Equipment list area.Logout

Contains the commands to deactivate the login with one or more remote equipment presinto the Equipment list area.

Refresh

Contains the commands to request the updating of the information present into Equipment list area.



EquipmentContains the commands to check the configuration, composition, functional status etc. ofthe equipment selected into the Equipment list area.

NetworkContains the commands for the management of the users that can use the program.

OptionContains the commands to customize the program (number of signals that can be stored

into the alarm history, connection modes and parameters, etc.).

ToolsContains the command to save, open, display, transfer a configuration file, the commandfor the management of the “remote equipment” list and the command to display themonitoring files (alarms and PM measurements) detected with the Siae Alarm &Performance Monitoring program

Menu Equipment:

Menu Equipment description

LCT Interface,

they allow opening the equipment graphical interface (Local Craft Terminal or LoOperator Manager).

Properties,

it allows checking the features (network identification code, addresses, reference date/timetc.) and executing the software reset of the equipment.

View Current Alarms,

it allows checking the current alarms.



Alarm Severity Config,

it allows changing the forwarding status of the alarms/trap and the seriousness lecoupled with the alarms.

View Active Manual Operation,

it allows checking the actually activated manual operations and setting the time (timeo

after which the forcing operations are automatically deactivated.History Events Realignment,

it allows realigning the information relevant to the alarms, memorized into the disk of PC and displayed into the Alarm History Log area, with the ones really present into selected equipment.

Version,

it allows checking the version and executing the updating of the equipmsoftware/firmware.

Performances,

it allows checking the list of the Performance Monitoring measurements available for tselected equipment type, the status (activated or deactivated) of each single measuremand the relevant results.

Units,

it allows checking the characteristics of the hardware that composes the equipment.

Diagnosis,

it allows running the diagnostics program which, analyzing the active alarms of the selectequipment, returns the possible causes that have triggered the alarms themselves.

Communication Setup,

it allows checking and changing the connection parameters (IP address, baud rate, routtable, OSPF parameters, etc.) used by the equipment.

IP/OSI Table Alignment,

it allows copying the elements present into the “remote element list” of the local equipmeinto the “Remote Element List” of the selected equipment.

Disable/Enable,

it allows disabling and then re-enabling again the connection of a equipment with tprogram.

Equipment Features Management, (Optional)

allows checking the functionalities (capacity and additional service channels, managemof OSPF protocol, etc.) enabled for the selected equipment.

Warning. This command is available only for equipment of PDH-AL type.



Equipment Inventory Report,

allows saving to file the configuration and the network parameters of the selecequipment.

PART 3LCT InterfaceTo access to the LCT Interface: Equipment LCT Interface

Interface LCT



Description of the higher part of the LCT interface

Channel and Frequencies Transmit and receive.

Lower Parity Higher Parity

Channel 7 Channel 7’



Configuration 1+ 0

Configuration: Equipment configuration

ODUIDU ODU IDU



Modulation / Capacity

The choice between 4,16 QAM et 8,16, 32 et 64 M Bits is made only locally

Link ID CapacityThe choice between 4,16 QAM et 8,16, 32 et 64 M Bits s is made on remote site first and secondly locally



Tributary: 16x2Mbits on Equipment situated on thfront of panel de l’IDU

Tributary: Put into service one of 16x2Mbits 2 MBits



Click on switch to

declare the 2MBits Tributary

channel.

It decrease the

If no 2M Bitsare not

connected on

this Port

At nearly the same time, this action

has to be performed on Remote and Local side,

For this short period, the alarm De-

multiplexer will appear, and disappeared when the local and

remote tributary shall be activated or deactivated.



Independent loop on 16 x 2 M Bits line side and Radiside

Radio Branch

Frequency Change only Locally

2M Bits

loop

2Mbits

Radio

1) To select other

frequency, use the lift

on the left of theWindows

Frequency to bechanged is in red

2) Click on Lock

Channel

3) Click on Apply



Link Branch

Frequency Change on the link, both remote and local side with one click on local side

Radio Branch: Power Manual Mode and Automatic Mode

Automatic: ATCPThis allowed to limited the

transmit Power ²of transmitter:

-To preserve frominterferences other microwave

-To limit the consum tion



Radio Branch: SettingCarrier on/off. Tx on/off. Power supply on/off



Configurare-LAN:

LAN 1:







LAN 2:







LAN 3:







INTERNAL PORT:







ETHERNET SWITCH:



Virtual-Lan configuration:



Adaugare VLAN 1.

Vid = 1

LAN 1 = Ena. Untagged

LAN 2 = Disable LAN 3 = Disable

PORT 1 = Ena. Tagged

Apply

Adaugare VLAN 2.

Vid = 2

LAN 1 = Disable


LAN 3 = Disable


Apply

Adaugare VLAN 3.

Vid =3

LAN 1 = Disable LAN 2 = Disable



Apply



Cum trebuie sa arate configuratia finala dupa adaugarea celor 3 Vlan-uri:



Ex. Configurare SIAE:

Ex. Wo IT:

Ip Management : IP 172.17.64.70,Net Mask 255.255.255.224, Def.Gw 172.17.64.65IP RAU A : IP 172.17.37.49,Net Mask 255.255.255.252

IP RAU B : IP 172.17.37.50,Net Mask 255.255.255.252Radio 1USER:SYSTEM

PASS:SIAEMICR

Radio 1/2USER:SYSTEM

PASS:SIAEMICRO

Radio A Equipment type ALC (NMS=Q3)

1.Equipment /Properties : Radio A / Agent IP: 172.17.64.70

Comunication Setup / Port Configuration

IP Eth : 172.17.64.70

255.255.255.224

LCT PPP : 1.0.0.1

255.255.255.252

PPP RADIO : 172.17.37.49

255.255.255.252

Client

Set Values /Store

2.Comunication Setup/ Stored Routing TableRouting Table : 2.0.0.0

255.255.255.252

Next Hop 172.17.37.50 pe RadioDef.Gateway: 172.17.64.65 pe LAN

3.Tools/Subnetwork Configutaion Wizard(se foloseste pt ca A sa vada B)

New Configutation/Add Station

Add Element 1 :IP 172.17.64.70 Managed by SCTAdd Element 2 :IP 172.17.37.50 Remote Link

Actul Configuration se bifeaza Station/Send



Radio B Equipment type ALC (NMS=Q3)

1. Equipment /Properties : Radio B / Agent IP: 172.17.37.50

Comunication Setup / Port Configuration

IP Eth : 10.17.1.1 ?????? nu conteaza

255.255.255.252 nu conteaza

LCT PPP : 2.0.0.1255.255.255.252

PPP RADIO : 172.17.37.50

255.255.255.252

Client

Set Values /Store

2.Comunication Setup/ Stored Routing TableRouting Table : -

Def.Gateway: 172.17.37.49 pe Radio

3.Tools/Subnetwork Configutaion Wizard(se foloseste pt ca B sa vada A)Add Station

Add Element 1 :IP 172.17.37.50 Managed by SCT

Add Element 2 :IP 172.17.64.70 Remote Link

Actul Configuration se bifeaza Station/SendOBS.

Se reseteaza echipamentul 1-2 minute

Equipment /Comunication Setup / Port Configuration / Set Values /Store/Restart1.Equipment type ALC (NMS=Q3)

2.Equipment type AL plus (NMS=Q3 - 2porturi cu rol de switch)

View Active Manual Operation (mentenanta)

Marius Cavai- Dobresc

Documents

Configurare SIAE