1

CONTENTS

 

Chapter 1 Introduction ....................................................................................... 3

1.1 Features ........................................................................................................................................................3

1.2 About the Kit ................................................................................................................................................4

1.3 Getting Help .................................................................................................................................................5

Chapter 2 ICB Architecture ................................................................................. 6

2.1 Layout and Components...............................................................................................................................6

2.2 Block Diagram of the ICB............................................................................................................................7

Chapter 3 Board Components............................................................................. 9

3.1 HSMC Expansion Connector .......................................................................................................................9

3.2 GPIO Interface ...........................................................................................................................................12

3.3 RS-232 Interface ........................................................................................................................................13

3.4 RS-485 Interface ........................................................................................................................................14

3.5 CAN Interface ............................................................................................................................................16

3.6 PIO Interface ..............................................................................................................................................16

Chapter 4 Assembling the ICB........................................................................... 18

4.1 Assemble ICB with DE2-115 .....................................................................................................................18

4.2 Generate ICB Project via DE2-115 System Builder ..................................................................................19

Chapter 5 ICB Demonstrations...........................................................................25

5.1 System Requirements .................................................................................................................................25

5.2 RS-232 Communication .............................................................................................................................25

5.3 RS-485 Loopback Test ...............................................................................................................................27

5.4 CAN Loopback Test ...................................................................................................................................29

Chapter 6 Appendix.......................................................................................... 32

1

2

6.1 Revision History.........................................................................................................................................32

6.2 Copyright Statement...................................................................................................................................32

 

Chapter 1

Introduction

The Industrial Communication Board (ICB-HSMC) is designed to provide common industry standard interfaces for FPGA platforms that support RS-232, RS-485, and CAN connectivity through a High-Speed Mezzanine Connector (HSMC). It allows users to setup a communication network for industrial use through the industrial standard interfaces on the ICB. This board features one RS-232 interface, one GPIO interface, four RS-485 interfaces, two CAN interfaces, and four PIO interfaces. The ICB is an ideal addition to the DE2-115 platform for developing industrial networking solutions on Altera FPGAs.

3

1.11.1 Features Features

Figure 1-1 shows a photograph of the ICB.

Figure 1-1 Layout of the ICB

The key features of the card are listed below:

4

• HSMC Connector • 40-Pin GPIO interface

o 36 user I/Os

• Two 6-Pin PIO interfaces o 4 user I/Os per interface

• 12-Pin PIO interface o 8 user I/Os

• RS-232 interface o Maxim RS-232 transceiver (MAX3238) support streaming transmission up to 250kbps o Complete RS-232 signal interface o 1 male DB9 Connector and one 10-pin header (shares pins with DB9 Connector)

• RS-485 interface o Analog Device isolated RS-485 transceiver (AMD2486), Profibus compliant o Half-duplex transmission with data rate up to 20Mbps o 4 channel transceivers, two channels output with DB9 female connectors and 10-pin

headers (share pins with DB9), two channels output with 10-pin headers

• CAN interface o Maxim Low-Supply-Current CAN transceiver (MAX3051) o High speed operation up to 1Mbps o 2 male DB9 and two 10-pin headers (share pins with Connectors)

• Power o Isolated 5V power supply for RS-485 transceiver bus side o 5V/3.3V power supply

1.21.2 About the Kit About the Kit

The kit will come with the following contents:

• ICB-HSMC • System CD-ROM

The system CD contains technical documents of the ICB, which includes component datasheets, demonstrations illustrating connectivity of the CAN, RS-232 and RS-485 ports, schematic, and user manual.

Figure 1-2 shows the ICB contents.

Figure 1-2 ICB contents

5

1.31.3 Getting Help Getting Help

Here is information of how to get help if you encounter any problems:

• Terasic Technologies • Tel: +886-3-550-8800 • Email: support@terasic.com

Chapter 2

ICB Architecture

This chapter describes the architecture of the ICB including block diagram and components.

6

2.12.1 Layout and Components Layout and Components

The picture of the ICB is shown in Figure 2-1 and Figure 2-2. It depicts the layout of the board and indicates the locations of the connectors and key components.

Figure 2-1 The ICB-HSMC PCB and component diagram (top view)

` Figure 2-2 The ICB-HSMC PCB and component diagram (bottom view)

The following interfaces are provided on the ICB:

• HSMC Connector (J7) • 40-pin GPIO Header (J3) • 6-pin Header (JP1/JP6) • 12-pin Header(JP7) • 10-pin Header (JP2/JP3/JP4/JP5/JP6/JP9/JP10) • DB9 Connector (J1/J2/J4/J5/J6)

7

2.22.2 Block Diagram of the ICB Block Diagram of the ICB

Figure 2-3 shows the block diagram of the ICB-HSMC. The HSMC connector houses all the wires from peripheral interfaces and makes to the FPGA on the main board.

Figure 2-3 Block diagram of ICB-HSMC

8

Chapter 3

Board Components

This chapter describes the components, connectors, and pin assignments on the ICB.

9

3.13.1 HSMC Expansion Connector HSMC Expansion Connector

The HSMC interface provides a mechanism to extend the peripheral set of an FPGA host board by means of a mezzanine card, which can address today’s high speed signaling requirement as well as standard or legacy low-speed device interface support. Table 3-1 lists the pin assignments of the HSMC connector.

Table 3-1 Pin assignments and descriptions on HSMC connector

Pin Numbers Name Direction Description 1-32 - - - 33 HSMC_SDA Input/Output HSMC serial address/data I/O34 HSMC_SCL Output HSMC serial clock 35 HSMC_TCK Output JTAG clock 36 HSMC_TMS Output JTAG mode select 37 HSMC_TDO Input JTAG test data out 38 HSMC_TDI Output JTAG test data in 39 - - - 40 - - - 41 GPIO_DATA34 Input/Output GPIO data 42 GPIO_DATA33 Input/Output GPIO data 43 GPIO_DATA35 Input/Output GPIO data 44 GPIO_DATA32 Input/Output GPIO data 45 VCC3P3 Power Power 3.3V 46 VCC12 Power Power 12V 47 GPIO_DATA4 Input/Output GPIO data 48 GPIO_DATA0 Input/Output GPIO data 49 GPIO_DATA5 Input/Output GPIO data 50 GPIO_DATA1 Input/Output GPIO data 51 VCC3P3 Power Power 3.3V 52 VCC12 Power Power 12V

10

53 GPIO_DATA6 Input/Output GPIO data 54 GPIO_DATA2 Input/Output GPIO data 55 GPIO_DATA7 Input/Output GPIO data 56 GPIO_DATA3 Input/Output GPIO data 57 VCC3P3 Power Power 3.3V 58 VCC12 Power Power 12V 59 GPIO_DATA12 Input/Output GPIO data 60 GPIO_DATA8 Input/Output GPIO data 61 GPIO_DATA13 Input/Output GPIO data 62 GPIO_DATA9 Input/Output GPIO data 63 VCC3P3 Power Power 3.3V 64 VCC12 Power Power 12V 65 GPIO_DATA14 Input/Output GPIO data 66 GPIO_DATA10 Input/Output GPIO data 67 GPIO_DATA15 Input/Output GPIO data 68 GPIO_DATA11 Input/Output GPIO data 69 VCC3P3 Power Power 3.3V 70 VCC12 Power Power 12V 71 GPIO_DATA20 Input/Output GPIO data 72 GPIO_DATA16 Input/Output GPIO data 73 GPIO_DATA21 Input/Output GPIO data 74 GPIO_DATA17 Input/Output GPIO data 75 VCC3P3 Power Power 3.3V 76 VCC12 Power Power 12V 77 GPIO_DATA22 Input/Output GPIO data 78 GPIO_DATA18 Input/Output GPIO data 79 GPIO_DATA23 Input/Output GPIO data 80 GPIO_DATA19 Input/Output GPIO data 81 VCC3P3 Power Power 3.3V 82 VCC12 Power Power 12V 83 GPIO_DATA28 Input/Output GPIO data 84 GPIO_DATA24 Input/Output GPIO data 85 GPIO_DATA29 Input/Output GPIO data 86 GPIO_DATA25 Input/Output GPIO data 87 VCC3P3 Power Power 3.3V 88 VCC12 Power Power 12V 89 GPIO_DATA30 Input/Output GPIO data 90 GPIO_DATA26 Input/Output GPIO data 91 GPIO_DATA31 Input/Output GPIO data 92 GPIO_DATA27 Input/Output GPIO data 93 VCC3P3 Power Power 3.3V 94 VCC12 Power Power 12V 95 RS232_RI Output RS-232 RI 96 RS232_RTS Input RS-232 RTS 97 RS232_CTS Output RS-232 CTS 98 RS232_DTR Input RS-232 DTR 99 VCC3P3 Power Power 3.3V 100 VCC12 Power Power 12V

11

101 PIO1_DATA0 Input/Output PIO1 data 102 PIO0_DATA0 Input/Output PIO0 data 103 PIO1_DATA1 Input/Output PIO1 data 104 PIO0_DATA1 Input/Output PIO0 data 105 VCC3P3 Power Power 3.3V 106 VCC12 Power Power 12V 107 PIO1_DATA2 Input/Output PIO1 data 108 PIO0_DATA2 Input/Output PIO0 data

109 PIO1_DATA3 Input/Output PIO1 data 110 PIO0_DATA3 Input/Output PIO0 data 111 VCC3P3 Power Power 3.3V 112 VCC12 Power Power 12V 113 PIO3_DATA0 Input/Output PIO3 data 114 PIO2_DATA0 Input/Output PIO2 data 115 PIO3_DATA1 Input/Output PIO3 data 116 PIO2_DATA1 Input/Output PIO2 data 117 VCC3P3 Power Power 3.3V 118 VCC12 Power Power 12V 119 PIO3_DATA2 Input/Output PIO3 data 120 PIO2_DATA2 Input/Output PIO2 data 121 PIO3_DATA3 Input/Output PIO3 data 122 PIO2_DATA3 Input/Output PIO2 data 123 VCC3P3 Power Power 3.3V 124 VCC12 Power Power 12V 125 RS485_2_RXD Input RS-485 channel 2 RXD 126 RS485_0_RXD Input RS-485 channel 0 RXD 127 RS485_2_TXD Output RS-485 channel 2 TXD 128 RS485_0_TXD Output RS-485 channel 0 TXD 129 VCC3P3 Power Power 3.3V 130 VCC12 Power Power 12V 131 RS485_2_RTS Output RS-485 channel 2 RTS 132 RS485_0_RTS Output RS-485 channel 0 RTS 133 RS485_3_RXD Input RS-485 channel 3 RXD 134 RS485_1_RXD Input RS-485 channel 1 RXD 135 VCC3P3 Power Power 3.3V 136 VCC12 Power Power 12V 137 RS485_3_TXD Output RS-485 channel 3 TXD 138 RS485_1_TXD Output RS-485 channel 1 TXD 139 RS485_3_RTS Output RS-485 channel 3 RTS 140 RS485_1_RTS Output RS-485 channel 1 RTS 141 VCC3P3 Power Power 3.3V 142 VCC12 Power Power 12V 143 RS232_DSR Output RS-232 DSR 144 POWER_VALID Output RS-485 0,1,2,3 power valid 145 RS232_TXD Output RS-232 TXD 146 RS232_DCD Output RS-232 DCD 147 VCC3P3 Power Power 3.3V

148 VCC12 Power Power 12V 149 CAN1_T Output CAN channel 1 TXD 150 CAN0_T Output CAN channel 0 TXD 151 CAN1_R Input CAN channel 1 RXD 152 CAN0_R Input CAN channel 0 RXD 153 VCC3P3 Power Power 3.3V 154 VCC12 Power Power 12V 155 - - - 156 RS232_RXD Input RS-232 RXD 157 - - - 158 - - - 159 VCC3P3 Power Power 3.3V 160 GND Power Power Ground

12

3.23.2 GPIO Interface GPIO Interface

This section describes the GPIO interface on the ICB

The ICB contains a GPIO interface with a 40-pin header. Figure 3-1 shows the pin names defined on the GPIO connector used in general purpose applications. For pin mapping information between the GPIO and HSMC connector, please refer to Table 3-1, using pin names here as indexes.

Figure 3-1 Pin names defined on GPIO connector

GPIO is widely used for housing various application needs such as video processing or image acquisition, etc. It supports up to 50MHz data rate using a reliable cable connection. Each data pin on the GPIO is connected to an extra protection circuit made up of two clamping diodes and one serial resistor. Figure 3-2 shows the protection circuitry that is on each of the 36 data pins on the 40-pin header.

Figure 3-2 Protection circuit for data pins on GPIO

13

3.33.3 RS-232 Interface RS-232 Interface

This section describes the RS-232 interface on the ICB-HSMC.

The ICB provides a full featured RS-232 interface using a Maxim 3238 chip with a guaranteed data rate of 250 Kbps. Figure 3-3 shows the I/O connectors J4 and JP8 for the RS-232 signals.

Figure 3-3 Wiring between the HSMC and RS-232 interface

The male RS-232 connector provides the industrial standard cabling interface, in addition to a 10-pin header used for simple communication conditions where a specific cable is not needed.

14

3.43.4 RS-485 Interface RS-485 Interface

This section describes RS-485 interface on the ICB-HSMC.

There are four RS-485 links from the HSMC connector to two female DB9 connectors and four 10-pin headers. Two of the 10-pin headers share pins with the two DB9 connectors. Within the four ports, two ports are compliant with the profibus specification and are suitable of using as physical link in industrial multi-terminal control applications. Figure 3-4 shows the hardware wiring between the HSMC and one RS-485 channel.

Figure 3-4 Wiring between HSMC and RS-485 interface

Table 3-2 gives the pin assignments on 10-pin headers and DB9 connectors for RS-485 signals.

Table 3-2 Pin assignments and descriptions for RS-485 interfaces

RS-485 Channel Signal Name 10-pin Header DB9 connector RS485_0_A 5(JP3) 3(J2) RS485_0_B 6(JP3) 8(J2) RS485_0_RTS_CON 7(JP3) 4(J2) VCC5_ISO 2(JP3) 6(J2)

Channel 0 (Profibus compliance)*

GND 9(JP3) 5(J2) RS485_1_A 6(JP2) 8(J1) RS485_1_B 5(JP2) 3(J1) RS485_1_RTS_CON 7(JP2) 4(J1) VCC5_ISO 2(JP2) 6(J1)

Channel 1

GND 9(JP2) 5(J1) RS485_2_A 5(JP5) - RS485_2_B 6(JP5) - RS485_2_RTS_CON 7(JP5) - VCC5_ISO 2(JP5) -

Channel 2 (Profibus compliance)*

GND 9(JP5) - RS485_3_A 6(JP4) - RS485_3_B 5(JP4) - RS485_3_RTS_CON 7(JP4) - VCC5_ISO 2(JP4) -

Channel 3

GND 9(JP4) - *Note, the Profibus implementation is not fully tested on the ICB.

15

16

3.53.5 CAN Interface CAN Interface

This section describes the CAN interface on the ICB-HSMC.

The board features two CAN links from the HSMC connector to two DB9 male connectors and two 10-pin headers. These two 10-pin headers share the same pins with two DB9 connectors. Figure 3-5 shows the connections between the HSMC and the CAN interface through a CAN transceiver chip.

Figure 3-5 Wiring between HSMC and CAN interface

Table 3-3 gives the pin assignments on 10-pin headers and DB9 connectors for CAN signals.

Table 3-3 Pin assignments and descriptions for CAN interfaces

CAN Channel Signal Name 10-pin Header DB9 Connector CANH 4(JP10) 7(J6) CANL 3(JP10) 2(J6) Channel 0 GND 2,5(JP10) 3,5,6(J6) CANH 4(JP9) 7(J5) CANL 3(JP9) 2(J5) Channel 1 GND 2,5(JP9) 3,5,6(J5)

3.63.6 PIO Interface PIO Interface

This section describes the PIO interface on the ICB-HSMC.

The board has four PIO links from the HSMC connector with two 6-pin ports and one 12-pin port (dual PIO link). The 6-pin PIO port not only provides four general-purpose I/Os but also has one 3.3V power supply and one ground pin. Figure 3-6 gives the related schematic of the PIO connector.

Figure 3-6 Wiring between HSMC and PIO interface

17

Chapter 4

Assembling the ICB

This chapter gives instructions for connecting the ICB to versatile host boards.

18

4.14.1 Assemble ICB with DE2-115 Assemble ICB with DE2-115

For connecting the ICB to the DE2-115 board, plug the ICB to the HSMC ‘socket’ (JP8) of the DE2-115 board. Users could additionally screw on and tighten the connection for extra mechanical stability. Figure 4-1 shows the assembled hardware.

Figure 4-1 Assembling ICB with DE2-115 board

Note that the ICB is designed to use the 3.3V or 2.5V I/O signaling standard. Before powering on the DE2-115 board, set the desired I/O standard for the HSMC connector. Figure 4-2 shows the header for setting the HSMC power supply voltage.

Figure 4-2 HSMC VCCIO supply voltage setting header (JP7)

19

4.24.2 Generate ICB Project via DE2-115 System Builder Generate ICB Project via DE2-115 System Builder

The DE2-115 board comes with a useful utility that helps users generate top level design and pin assignment files that include specific HSMC daughter card information. The automatically generated top level design and Quartus II setting file eliminate potential common mistakes encountered when manually typing in the signal wires between DE2-115 and daughter card.

Install and launch the DE2-115 System Builder

The DE2-115 System Builder is available from the DE2-115 system CD-ROM, under the DE2_115_tools folder. Users can copy the entire folder to a host PC without installing the utility. Before using the DE2-115 System Builder, execute the DE2_115_SystemBuilder.exe on the host computer as shown in Figure 4-3.

Figure 4-3 The DE2-115 System Builder window

Input Project Name

Input project name as show in Figure 4-4.

Project Name: Type in an appropriate name here, it will automatically be assigned as the name of your top-level design entity.

20

Figure 4-4 The DE2-115 Board Type and Project Name

System Configuration

Under System Configuration, users can enable the desired components on the FPGA host board as shown in Figure 4-5. If the component is enabled, the DE2-115 System Builder will automatically generate the associated pin assignments, including the pin names, pin locations, pin directions, and I/O standards.

21

Figure 4-5 System Configuration Group

HSMC Expansion

Figure 4-6 illustrates the usage of the DE2-115 System Builder specifying ICB connecting to the HSMC interface. This will automatically generate wiring connections between the host board and ICB-HSMC.

22

Figure 4-6 HSMC Expansion Group

The “Prefix Name” is an optional feature that denotes the pin name of the daughter card assigned in your design. Users may leave this field empty.

Figure 4-7 illustrates the generated top level design file contains information on the ICB-HSMC connections.

23

Figure 4-7 Top level design file includes ICB-HSMC information

24

Chapter 5

ICB Demonstrations

This chapter mainly depicts how to use the ICB through a set of demonstrations located on the software CD. From running the demonstrations, users will know how to implement codes on the DE2-115 for controlling the ICB-HSMC. The demos include communication between RS-232 and PC, RS-485 loopback test, and CAN loopback test.

25

5.15.1 System Requirements System Requirements

Here are boards and connecting wires used to run the demonstrations:

• DE2-115 board 1 • ICB-HSMC 1 • RS232 cable (DB9 female-female cross cable) 1 • Connecting wires 4

5.25.2 RS-232 Communication RS-232 Communication

This demonstration illustrates how to construct a communication channel between a PC and RS-232 port on the ICB card. Set up of the RS-232 port as follows:

• Baud rate: 9600 bps • Data bits: 8 bits • Stop bit: none • Parity check bit: 1 bit

The demonstration also provides PC-side UART terminal communication software using the above parameters. The software running on the PC transmits characters out to the RS-232 port on ICB. Through the HSMC connector, the UART controller implemented on the DE2-115 board buffers the received characters and then sends back to the RS-232 link. The terminal software on PC side senses the receive channel and displays the information in a software window. The system block diagram is shown in Figure 5-1.

Figure 5-1 Block diagram of RS-232 communication

Demonstration source code

• Project Directory: \Demonstrations\DE2_115_ICB_RS232 • Bit Stream Used: DE2_115_ICB_RS232.sof

PC terminal software

• Software Directory: \Demonstrations\DE2_115_ICB_RS232\SW • Executable File : UartTerminal.exe

Demonstration batch file

• Batch File Folder: \Demonstrations\DE2_115_ICB_RS232\demo_batch • Batch File: DE2_115_ICB_RS232.bat, test_bashrc • FPGA Configuration File: DE2_115_ICB_RS232.sof

Demonstration setup:

• Assemble the ICB with the DE2-115. • Power on the DE2-115 board. The green LED (D40) near the HSMC connector will indicate a

valid connection. • Connect the DE2-115 to the PC using the USB-Blaster cable and then run the demo batch

DE2_115_ICB_RS232.bat under the \Demonstrations\ DE2_115_ICB_RS232\demo_ batch\ folder.

• Connect the RS-232 port on the ICB to the PC using a DB9 female-to-female cross cable (Tx and Rx lines are cross connected on two headers to form a peer-to-peer connection).

• Run the UartTerminal.exe on the PC, and then select COM1 as the transceiver channel. The software will initiate COM1 and display the success information as shown in Figure 5-2.

• Input characters for transmission in the edit box and then press Transmit. • Press Receive for showing the received data.

26

Figure 5-2 Terminal software interface

27

5.35.3 RS-485 Loopback Test RS-485 Loopback Test

This demonstration illustrates a loopback test through RS-485 interfaces using the UART protocol. Channel 0 of the RS-485 interface (marked as Profibus-1) connects to RS-485 channel 1. Software running on Nios II will first set channel 0 on transmit state and channel 1 on receive state, then it initiates one data transfer with its content set by SW7-0 through channel 0. Once the data is received by the RS-485 controller on channel 1 side, software will set channel 1 on transmit state and channel 0 on receive state then sends data back to the loop. The RS-485 controller on channel 0 side finally gets the passed back data and compares it to the original data. The same procedure will be carried out for channel 2 and 3 except transmit data is set by SW15-8. The result will be indicated on HEX3-0 and HEX7-4 as well as Nios II IDE. Figure 5-3 shows the block diagram of the test system.

Figure 5-3 Block diagram of the RS-485 loopback test

Demonstration source code

• Project Directory: \Demonstrations\ DE2_115_ICB_RS485 • Bit Stream Used: DE2_115_ICB_RS485.sof • NIOS II Workspace: \Demonstrations\ DE2_115_ICB_RS485\software

Demonstration batch file

• Batch File Folder: \Demonstrations\DE2_115_ICB_RS485\demo_batch • Batch File: DE2_115_ICB_RS485.bat, test_bashrc • FPGA Configuration File: DE2_115_ICB_RS485.sof

Demonstration setup:

• Connect ICB to DE2-115. • Establish the loopback by connecting RS-485 channel 0 with channel 1. Note profibus ports

(JP3, JP5) have wires A & B swapped. Figure 5-4 shows the wiring diagram for two loops. • Power on DE2-115 board. Validate the connection by examining the status of the green LED

near the HSMC connector. • Change the transmit contents by setting the values of SW7-0 for loop pair 1(channel 0 and 1),

SW15-8 for loop pair 2(channel 2 and 3). • Connect the DE2-115 to the PC using USB-Blaster cable, and execute

DE2_115_ICB_RS485.bat under the \Demonstrations\ DE2_115_ICB_RS485\demo_batch\ folder.

• The prompt window will give test result information as shown in Figure 5-5. • On the DE2-115 board, HEX3-0 indicates loopback information between channel 0 and 1.

HEX7-4 indicates loopback information between channel 2 and 3. Table 5-1 depicts the information indicated on the HEXs.

Figure 5-4 Wiring for the RS-485 loopbacks

28

Figure 5-5 Test results on the prompt window

Table 5-1 Loopback test result on HEXs for RS-485

Test Pass Info. Test failed info.

S-<test data*> FAIL

*test data represents the value set by SW15-8 or SW7-0.

29

5.45.4 CAN Loopback Test CAN Loopback Test

This demonstration illustrates how to construct a communication loop between two CAN interfaces where one initiates the data transfer and the other receives data then sends it back to the loop. SW7-0 is used to set up the transmit data contents. The data loopback flow for CAN is the same as RS-485. In this demonstration, the Nios II processor in the FPGA on the DE2-115 board takes charge of the control work and gives the test result information. The block diagram of the CAN loopback test is as shown in Figure 5-6.

Figure 5-6 Block diagram of CAN loopback test

Demonstration source code

• Project Directory: \Demonstrations\ DE2_115_ICB_CAN • Bit Stream Used: DE2_115_ICB_CAN.sof • NIOS II Workspace: \Demonstrations\ DE2_115_ICB_CAN\software

Demonstration batch file

• Batch File Folder: \Demonstrations\DE2_115_ICB_ CAN\ demo_batch • Batch File: DE2_115_ICB_ CAN.bat, test_bashrc • FPGA Configuration File: DE2_115_ICB_ CAN.sof • NIOS II Program: DE2_115_ICB_ CAN.elf

Demonstration setup:

• Connect ICB to DE2-115. • Connect ‘H’ and ‘L’ wire of CAN 0 and CAN1 respectively. Figure 5-7 shows the wiring

manner for the CAN loopback test. • Power on DE2-115 board. Validate the connection by examining the status of the green LED

near the HSMC connector. • Set the transmitting data for the loop by toggling SW7-0. • Execute the DE2_115_ICB_CAN.bat in the \Demonstrations\ DE2_115_ICB_CAN \demo

batch\ folder. • The prompt window will display the test result information as shown in Figure 5-8. • HEX3-0 on the DE2-115 also prints out the loopback test information. Table 5-2 depicts the

information indicated on the HEXs.

30

Figure 5-7 Wiring for CAN loopback test

Figure 5-8 Prompt information while running the test

Table 5-2 Loopback test result on HEXs for CAN

Test Pass Info. Test failed info.

S-<test data*> FAIL

*test data represents the value set by SW7-0.

31

Chapter 6

Appendix

32

6.16.1 Revision History Revision History

Version Change Log V1.0 Initial Version (Preliminary)

6.26.2 Copyright Statement Copyright Statement

Copyright © 2010 Terasic Technologies. All rights reserved.