MAX 20

REV. 4.0

DIGITAL EGG INCUBATOR

USER'S MANUAL

How to use Rcom MAX 20

Contents

(1) Rcom 20 Introduction1. Introduction

(2) Safety Precautions

(3) Identification of Parts and Composition

(4) Function of Digital Control & How to Operate

(1) How to Assemble the Incubator / Egg-Turning plate 2. Before use

(2) What is an incubation room?/ Preparation for Incubation

3. Function Settings(1)

(1)

(2) Change Cels.& Fahr.

(3) Temperature & Humidity Setting / How to Set Egg-Turning

(2) Dew Condensation4. Incubation

(2) Troubleshooting

6. Product Information(1) Servicing / Frequently Asked Questions (FAQ)

(3) Specification

Introduction

Before use

Function Settings

Incubation

How to Clean

Product Information

5. How to Clean(1) How to Disassemble(2) How to Clean

Humidity & Air Maintenance during Incubation /Maintenance after Hatching

Incubator Start&Termination /Return to Factory Setting

The result of Hatching can be changed by a large numbers of factors. Autoelex Co., Ltd. & our distributors will not take any responsibility for ‘Loss of eggs or pet/animal lives’ under any circumstances such as ‘Hatching/Brooding failures’, ‘User’s carelessness’, ‘Personal (un-certificated) conversion / alteration’, ‘Arbitrary using out of the machine’s purpose’, ‘Electric power failure’, or ‘Malfunctioning’. Please be sure that the machine works without any problem before placing Eggs or Pets(Animals). Also, we strongly recommend you to read the User’s Manual carefully to minimize of any failure.

Caution : Caution mark against a fault that can cause damage, trouble, or failure of incubation.

Tip : References or useful suggestions in using Rcom product

Mark Explanation

Warning of actions which may be dangerous or cause damage to the incubator.

Prohibited

Do not disassemble.

Do not touch.

It is necessary to keep.

Remove the power cord from outlet.

Ground Connection for preventing electric shock.

Rcom 20

Features

[Main Features]* Outer Temp. Sensor included for Automatic Adjustment of Heating rate responding to Incubation Room Temperature* Superior design with convenient operation* Optimum air circulation technique with 3 strong BLDC fans* Automatic Temp. & Humidity setting and control* Body locking device* Water supplement alarm function* 20 eggs capacity for chicken size eggs ( 52 Quail egg size / 10 Goose egg size)* Antiblastic Humidification method by heating water, which discourages bacterial growth* Double-glazed view window for minimizing the influence of outside temperature* Enhanced reliability by applying Swiss's Sensirion's 3rd generation temperature & humidity sensor* Powerful SMPS application for stable power supply

[Safety Features]* Alarm and display function of abnormal incubator temperature caused by sudden fluctuation of ambient temperature* Incubation data memory function and power outage notification function in case of power failure* Circulation fan cover for safety and electric safety cut-out switch on the upper main body for safety* Heater supporter designed for heater tension control and its safety* Safety cover applied for protecting humidification unit* Humidification unit durability improved by water proof BLDC fan* Alarm function when water needs replenishing

[Easy Features]* No need of separate humidification unit as it included in main body

* Easy attachment and detachment of double-glazed viewing window* Universal egg tray for various size eggs* Slide plate with embossed feature for preventing skid* Variable air vent for adjusting air supply* Bottom body designed for easy cleaning* Roller Dividers, which can safely apply egg turning for expensive or rare eggs. (Option)

Thank you for choosing the Rcom incubator.The Rcom 20 incubator is the first incubator with creditability to have a superior design and functionwhich help in controlling optimum incubation conditions. It has two sensors, one for detecting surrounding environments and the another for internal incubator conditions.The Rcom20 is designed easy to use and simple to use as a customer orientated product, but please remember that the user's incubation knowledge and proper operation are very important for the best incubation result. Therefore, be sure to read this user's manual carefully before you use this incubator. The Rcom 20 offers optimum incubation conditions, but users need to observe and manage all incubation conditions such as species of eggs, temperature or humidity for each incubation period, and an optimum incubation circumstances .

1. Introduction (1) Rcom 20 Introduction

1. Introduction

Electrical hazards Be careful the details below when you use.

Setting Cautions Be careful the details below when you use.

Do not pull the cord when taking out the power cord, and keep wet hands away from connecting plug.

Do not use a damaged power cord or loose outlet.

▶ Risk of electric shock or fire.

▶ Risk of electric shock or fire.

Do not insert multiple connecting plugs in an outlet.▶ Risk of fire or electrical overload.

Never pull the plug out of the outlet during the incubation period.▶ Incubation will be interrupted.

Do not twist or crush electric cord.▶ Risk of electric shock or fire.

Cleaning Cautions Be sure to disconnect the electric cordfrom the outlet before cleaning.

Clean the incubator by a soft cloth with a neutral detergent.

Do not spray cleanser directly on the incubator surface.

Do not use chemicals like wax,benzene, alcohol, thinner,aromatic, or lubricant, etc.

Brush away dust on the plug with a dry cloth.

For special cleaning of inner part per year, contact to the service center.▶ If you don't clean the inside ofincubator for a long time, dustcan cause some trouble or a fire.

Do not install under the direct sunlight.

Do not install in dusty or dirty environment.

▶ Risk of fire or interference with the incubation process.

▶ Risk of damage or fire within the incubator.

Do not install in excessively cold or hot conditions, cigarette smoke, etc.

Do not install in moist or humid environment.

▶ Risk of interference with the incubation process.

▶ Risk of fire or electric shock.

Do not use any other non-standard parts except those provided.▶ Risk of damage or hatching failure.

Please ensure that no small objects get intothe holes on the incubator.▶ Risk of electric shock or fire.

Do not disassemble or modify the incubator in any way.▶ Risk if electric shock or fire.

If the incubator soundsstrange or emits smoke contact your service center.▶ Risk of electric shock or fire.

If the incubator requires repair disconnect from the power supply and please contact to your service center.

Clean the incubator thoroughly before storing.

Install away from heat sources.▶ Risk of damage to the incubator case and interference with the incubation process.

Do not turn the incubator upside down.▶ Water will pour out of the incubator, and view window can be dropped or damaged.

Ensure that the incubator is installed on a stable surfaceaway from edges.▶ Risk of damage to incubator and eggs and user from accidental knocks or drops.

Do not cover the ventilating opening. ▶ Inner temperature can rise, interrupting incubation. ▶ Risk of knocking the incubator

or accidental interference with the controls.

Children should be supervisedto ensure that they do not playwith the appliance.

(2) Safety Precautions

Serial No.

(EX:RCM0950278)If you register your information with your machine’s serial number on our web-site(www.Rcom.co.kr), you can get 2 year warranty service.

1. Introduction (3) Identification of Parts and Compositio

Power Connecting (the rear)For connecting power cord.

Identification of Parts

Basic Components

For inlet of air from outside

Air inlet vent

For circulating warm air

Vents for air circulation

Water hole

To facilitate water top-up for the humidity control.

Adjust the space of dividersaccording to egg size.

Digital Control Center

See description ofthe function and operation.

Main Body-1Main Body-2

Locking Button

View Window

For a clear view of the incubation process.(Double Skin Viewing Window)

Egg Tray

Water Cap

Duplicated View Window

Universal Tray Divider(10EA)

View Window

Universal Tray SET

Power Cord

Small eggTray

Standard eggTray

Large eggTray

User's Manual

Easy function operation

Egg-Turning Plate

Rolling Divider SET

Main Body-1 Main Body-2

1. Introduction (4) Function of Digital Control & How to Operate

(Lighting when working)

Humidity DOWN Button

Temp. UP Button Temp. Display Humidity Display

Egg-Turning Setting Button

(Blink with water shortage)

Temp. DOWN Button

Setting Temp. UpCalibration Temp. Up

Setting Temp. DownCalibration Temp. Down

(Lighting when working)Turn on with automatic egg-turning mode.(Blink when working)

- Alarm for water supplement sounds in twice.( First alarm with water shortage / Second alarm after 3 hours )

Water Supplement LampEgg-Turning LampHeater Lamp

Setting value check

Humidification working lamp

Power Failure Alarm Function

Blink with power failure(to remove, press SET button)

Humidity UP Button

Setting Button

Setting Humidity UpCalibration Humidity Up

Setting Humidity DownCalibration Humidity Down

Automatic egg-turning settingor cancellation/ Egg-turning test

Function of Digital Control & How to Operate

What’s ‘Temperature&Humidity Setting’?This is that you set up temp.&humi. As you want to have inside of the machine.

[ Function Operation & Explanation ] If you want to change setting value, keep pressing "SET" button and change the value. put some water after take off label from the back and attach to the window.

How to OperateFunction Explanation

ChangingCels. & Fahr. Changing Cels. & Fahr.

Temp.Setting Setting of needed temp.

Humidity Setting

Egg-TurningInterval Setting

Setting of needed humidity.

How to OFFHumidification

Function

Egg-Turning Test Egg-Turning Test (once)

Initialization(Factory setting) Initialization

Set Humidity as 20%

Egg-Turning Interval Setting as required

20%

2. Before use (1) How to Assemble the Incubator / Egg-turning plate

How to Assemble

110V~120V

BACK

View Window

Egg-Turning Plate

Main Body-1

Universal Tray

Water Cap

Main Body-2

* Fit the water cap.

Gear connecting part

▶ If you do not assemble egg turning place correctly, it can cuase incubator failure.

▶ Gear connecting part of egg turning plate must be on the top side.

▶ Lock the three locking buttons at the front and rear of the incubator.

▶ Insert the power cord in the socket at the back of the main body.

* Fit the water cap. Be careful when you assemble egg turning plate.

2. Before use (2) What is an incubation room? / Preparation for Incubation

※ How to turn off Humidification Function : Set humidity level at RH 20%.

What's an Incubation Room? / Preparation for Incubation

1

2

Insert the electric cord in the connecting jack in the back of the main body and put the main plug into a socket. The FND display will light up and show temperature.

DISTILLEDWATER

Open the watercap and fill the hole with DISTILLED WATER and refill water after about 5 min. again up to the limit line on its inside mark. (If you refill water during the incubation period, humidity goes down temporarily.)

The Incubation Room is a confined space for setting and operating an incubator. Because the incubation room environment has a considerable effect on hatch rate, it's recommended to control the environment for setting up an incubator; there should be little noise and vibration around and temperature ranging 28℃(82.4℉) with small variation in temperature. Especially, if there are frequent occasions when the temperature drops suddenly at night, compared with daytime, be sure to check from time to time and pay attention so that the incubator is not directly exposed to sunlight during daytime.

After filling up with water, never shake or turn over the main body of the incubator, which would cause water to spill inside the body and could cause a breakdown.

In case you use the incubator without adding humidification water or intend to incubate eggs at low humidity under RH 20%, you must stop its humidification function. please turn off the humidity unit if the unit is empty water otherwise, humidity unit will be broke or you may not no longer use the unit. (When using this function, the alarm for sensing water drop will go out.) [See the description of humidification function OFF on Page 12]

During incubation period, check the DISTILLED WATER water levelabout every three days and refill water, if necessary. (After you refill water, check again after 5min. and refill again.)

110V~120V

20

20

2. Before use (2) What is an incubation room? / Preparation for Incubation

About 2mmAbout 2mm

3 Place the eggs to incubate in the egg groove and then close the view window.

※ When you use the 'universal rolling divider' which is sold separately, be careful to adjust the distance of rolling divider so that eggs do not roll out of position. Refer to the picture rignt side.

If you use Mineral water or Tap water for humidification, the humidity unit can be broken easily because of water scales. We strongly recommend you to use only “DISTILLED WATER” for your machine, and Autoelex Co.,Ltd & our distributors do not indemnify for warranty service not only if you have any problem with using mineral water, regular water, tab water and the like but also if you had improper management or handling for your machine. In this case, Autoelex Co.,Ltd. & our distributors will charge for your after service.

Some gap (about 2mm) around the eggs is needed for easy egg turning as shown on the below. ▼

Be careful to close the view window completely; if not, the temperature and humidity will fail to go up.

The egg to incubate must be a fertilized egg. (Refer to the guidebook.)

You can buy the ‘Distilled water’ in your local market, and if you have any question, please contact the shop, where you purchased your machine.

TEMP +

TEMP -

How to change Cels. & Fahr.

How to terminate incubation

How to start incubation

110V~120V

110V~120V

110V~120V

HOLD

Keep pressing SET button

▶ Press and buttons at the same time

and CA will show on Temp. display.

Then press button, it will change

as shown on the right.

▶ It is for returning to the factory default setting.

▶ It is for initializing the incubator setting or calibration to the factory settings when you handle the incubator improperly so that the value has changed. Unplug the power supply and hold SET button and re-plug the power supply as shown on picture. Then, rSt will show on the display, and the incubator will be initialized to factory setting.

Re-plug the power supply

▶ If you connect the incubator with power cord, second dot " . " of temp. display is blink with alarm. Press SET to remove blink and then it starts incubation with existing temperature and humidity. [Factory default setting - Temp. : 37.5℃ (99.5℉), Humidity : RH 45%]

▶ After all eggs are hatched, you should REMOVE the power cord for incubation termination. (The incubator has no separate power switch.)

▶ Be sure to turn ON egg turning before incubation starts and turn OFF before 3 days of hatching. At this time, it's recommendable to raise humidity up to 60~70%. [Refer to Egg Turning ON/OFF on Page 13.]

"rSt" will show on the display as below,and the incubator initialize to factory setting.

There can be some smell the first time you use the incubator, that is normal.

Power Failure Notification : When firstly input power, or power failure during incubation, second dot " . " of temp. display is blink with alarm. Press SET to remove.

Return to factory settings

3. Function Settings (1)Incubator Start&Termination /Return to Factory Setting(2) Changing Cels.&Fahr.

(Keep pressing the button)

(Keep pressing the button)

3. Function Settings (3) Temperature & Humidity Setting /How to Set Egg-Turning

▶ In a state of button being pressed, adjust the

humidity you want with or button.

humidity setting will be completed when you remove your

finger from the button, and the present humidity

of the incubator inside will be indicated.

▶ Be sure to set humidity RH 65 ~ 70% from 1~3 days before hatching.

Temperature and humidity can be different from normal setting levels according to the surroundingenvironment. (Refer to a incubation guidebook which is supplied separately.)

Temperature and humidity is optimized when Rcom products are released.We do no recommend customers to recalibrate by their own. If you need to recalibrate, please visit our

Because of low price thermometers and hygrometers are not accurate, e recommend you to use special Ⅱ)

▶ In a state of button being pressed, press button to adjust humidity at RH 19% and, then,

humidification function will be OFF. On the contrary, if you adjust humidity above RH 20%, its function will be ON.

How to Turn ON/OFF Humidification Function

How to Set Humidity

How to Set Temperature

▶ In a state of button being pressed, adjust the

temperature you want with or button.

Temperature setting will be completed when you remove

your finger from the button, and the present

temperature of the incubator inside will be indicated.

▶ In a state of button being pressed, adjust the

humidity you want with or button.

humidity setting will be completed when you remove your

finger from the button, and the present humidity

of the incubator inside will be indicated.

▶ Be sure to set humidity RH 65 ~ 70% from 1~3 days before hatching.

Temperature and humidity can be different from normal setting levels according to the surroundingenvironment. (Refer to a incubation guidebook which is supplied separately.)

If you press SET button, the present setting temperature and humidity will be indicated and, if you remove your finger from the button, the present inner temperature and humidity indicated.

If you set the incubator under a direct ray of light or too cold spot, the incubator temperature can be higher or lower than setting temperature.

In case you use the incubator without adding humidification water or intend to incubate eggs at low humidity under RH 20%, you must stop its humidification function. please turn off the humidity unit if the unit is empty water otherwise, humidity unit will be broke or you may not no longer use the unit.

Temperature and humidity is optimized when Rcom products are released.We do no recommend customers to recalibrate by their own. If you need to recalibrate, please visit our

Because of low price thermometers and hygrometers are not accurate, e recommend you to use special Ⅱ)

How to Set Abnormal High or Low Temperatue Alarm

How to Set Egg Turning ON/OFF

▶ In a state of button being pressed, press

button then the setting will be changed as required.

▶ What is Abnormal High or Low Temperature Alarm? It is alarm soulds when incubator temperature is higer or lower than setting value because of various reasons such as room temperature change or disorder of temperature controlling system.

▶ Egg Turning Test : If you press button for

about 5 seconds, egg turning test will be effected once.

(Keep pressing the button)

repeat

* Max. abnormal temp. alarm limit (0.0 ~ 5.0℃ Default Setting:2.0℃) * Min. abnormal temp. alarm limit (0.0 ~ -5.0℃ Default Setting:-3.0℃)

5Sec. Set required high range with

UP / DOWN button

Set required low range with

UP / DOWN button

Save setting and pass to current temp. & humi.

indication

Save setting and pass to

low humi. set

Be sure to set TURNING OFF 3 days before hatching.

▶ Plese press button over 5 seconds

to turn ON or OFF egg turning melody.

3. Function Settings (3) Temperature & Humidity Setting /How to Set Egg-Turning

4. Incubation (1) Humidity & Air Maintenance during Incubation / Maintenance after Hatching

(2) Dew Condensation

When the baby chickens hatch out, please move them into a brooder.

This is a naturally occurring phenomenon when there is a significant difference in temperature between inside and outside of the incubator during incubation period. If this occurs, water may form in inside bottom of the main body of the incubator(bottom part).

Maintenance after Hatching

Dew Condensation

Humidity & Air Maintenance During Incubation▶ When hatching, humidity should be relatively high to prevent the thin membrane from drying out or hardening before hatching.

▶ When hatching, it's recommended not to open the lid often. This is because if you open the lid often humidity will be rapidly decreased and it will take a long time to regain the proper humidity.

▶ It's very important to maintain humidity higher 1~2 days before hatching than the early and middle incubation periods. Humidity requirements during incubation are RH 45~55% for waterfowl, RH 40~45% for poultry and RH 35~45% for parrot, in general. One day before hatching, all kinds of birds need about RH 65% humidity and sometimes need higher than that. However, in areas of high ambient humidity, lower levels of humidity may be needed during incubation.

Incubator internal temperature is 37℃ (99.5℉) or more, and hatching room temperature is below 28℃, in that case, RH 70% humidity is may not be able. The difference of ±5% humidity value may occur from the humidity sensors difference, and there are no problems at hatching

It's very important to keep humidity higher than RH 60% before hatching 3days.

▶ As there is some difference in chick feed for each kind of bird, so it's desirable to obtain useful information about the chicks before hatching.

Be sure to use a three-wavelength 20W bulb. If you use a bulb over 20W. temperature goes up, possibly killing the chick or causing a fire. If there is too much water and a chick would falls into water, its feathers get wet and it can be died of loss of body heat. Here, dry feathers with a hairdryer. etcBe sure to use a three-wavelength 20W bulb :In case breeding room size 370 x 270 x 130(mm)

Hatcher : The machine for egg-hatching. Operate it 1~3 days before egg-hatching. (Rcom MARU H&B) Brooder : The machine makes baby chickens or birds warm up against cold or cool environment. You can set up proper temperature and humidity. (Rcom MARU H&B / Rcom Brooder Series)

Please do not try to egg-hatching in the incubator. It makes your incubator broken or faulty, and we do not give you free warranty service. (Please move all the eggs 1~3 days before hatching into Hatcher or Brooder.)

▶ It is necessary to use a brooder for baby chicken or bird since they are too week against cold or cool environment. If you try egg-hatching in your incubator, there would be lots of germs, feathers, which causes of low egg hatching possibility for your next hatching. Also, they can make your incubator broken or faulty. We strongly recommend you to use independent Hatcher or Brooder for egg-hatching. If you have any faulty or broken because of not using independent Hatcher or Brooder, we do not serve you the free warranty service. In other words, you have to pay for the service charge. To make a simple Hatcher or Brooder, please refer to the our web-site (www.Rcom.co.kr).

Unlock and remove the locking buttons for three parts at the front and back of incubator by pulling them forward.

How to disassemble and clean the incubator

1

2

3

110V~120V

▶ Pull out the electric cord from the connecting jack and also take out the plug from the outlet.

▶ When using humidification function, a lot of alien matter sticks to the humidification heating element ⓐ. This may not cause failure, but when terminating incubation please clean the humidifying heater lightly with a soft brush.

▶ If you place the main body(upper part) on the floor, please don't let the humidification heating part touch with the floor.

The bottom part of incubator should be thoroughly cleaned with water and dried. The upper part should be naturally dried in the well-ventilated place for about one day to remove moisture left inside of the incubator after hatching thoroughly.

back

Don't turn off the power soon after using the incubator, as this may cause a break down due to moisture left inside the main controller. At this time, it's better to firstly remove the water inside of the incubator and dry by operating it for 1hour and then turn it off or open the view window and dry it naturally for 2~3 hours and, then, re-operate it, which may lengthen the life time of incubator.(Set humidification function OFF. / Refer to the page 12.)

Don't clean the product with organic solvents such as benzene, thinner, etc. which may cause deformation or decoloration of the plastic parts.

If you inflict impact on the humidification heating part or scrape it with a sharp instrument, the humidifying heater will be damaged.

We kindly recommend you to use distilled waterIn order to reduce a foreign substance on the humidifying heater device.

5. How to Clean (1) How to Disassemble

4

5

Start the vacuum cleaner to remove the dust as shown on the right and thoroughly shake out the minute dust with a fine brush.

If you finish cleaning the incubator, reassemble it in the reverse order of disassembly. Wipe out outside the main body with a wet cloth and dry it in a cool and well-ventilated place beforestorage.

In case the incubator clean status is poor which may cause fan noisy or stopping.

If the incubator goes through incubations several times, feather, dust, shell, etc. accumulate inside the main body, which may cause a break down, so be sure to clean the product before storage.

Don't clean the product with organic solvents such as benzene, thinner, etc. which may cause deformation or decoloration.

[Refer to How to assemble on Page 8.]

Cleaningthe fan

5. How to Clean (2) How to Clean

(1) Servicing / Frequently Asked Questions (FAQ)6. Product Information

Frequently Asked Questions (FAQ)

Servicing

All our Rcom digital incubators of Autoelex Co., Ltd. are made by precision systems under strict quality control. But occasionally some defective products are found on the way of their distribution. If any problem occurs, then please contact Rcom service center or distributorsin your country. We will do our best to solve the problems, if any, for you. This product is designed in modular mode, so for its repair, if any, a qualified person can replace the part concerned with ease.

* Complaint Department : 82-55-337-2560 ＊E-mail Receipt : Rcom@Rcom.co.kr

Troubles Expected Causes (Possibility) Countermeasures

In case hatching rateis low

When a chick hatchesout earlier than expected or a deformed chickhatches out

When a chick hatchesout later thanexpected

When hatching datesare so different fromeach egg (When all chicks don't hatch out at the same time but over along period)

When intending to hatching various eggsat the same time

Setting temperature highEgg turning was not operating normally

Setting temperature low

Eggs stored for different lengths of time Diffferent incubation temperatures

Incubation days are different, so hatching rate falls down.

Eggs might be contaminated by chicks that hatched first.

When the egg is an unfertilized egg.Getting infected by germsWrong incubation setting Health condition of mother birdImproper egg turning

Inspect the egg to check possibility of egg surviving.

Disinfect the incubator. Check all settings of incubator.

Especially, check them focusing on the temperature.

Review care of health of mother bird. Check if egg turning is normal.

Minimize the time to store egg properly. Check Temperature difference

in the incubator. (sunlight, temp of incubation room, etc.)

Mark hatching date on eggs and move them to other incubator (brooder) just on the marked date.

In case of putting in many eggs at the same time, it's convenient to prepare a spare incubator available as a brooder

Lower temp. setting of the incubator about 0.5 (1 ) ex) 37.5℃ (99.5℉) 37.0℃ (98.6℉)

Check if egg turning function is OFF

Raise temp. setting of the incubator about 0.5 (1 )

ex) 37.0℃ (98.6℉) 37.5℃ (99.5℉)

Troubleshooting

CIRCUMSTANCE ITEMS TO BE CONFIRMED SOLUTIONS

Alarm sounds withHI indication(abnormal high temp.)

Alarm sounds withLO indication(abnormal low temp.)

Connect the cord again. Check the main socket with any other

electric appliances. Try to insert to another outlet.

Check electric cord is properly connected. Check if there is a power outage. Check whether the plug is damaged.

Temperature will not go high enough.

No signs of power to the incubator.

Check your setting temperature. Check the air circulation FAN is working. Initialize the incubator.

[Refer to the page 11]

Set the temperature as required. Take the power plug out of the outlet, and

disassemble the main body for cleaning around the air circulation fan with brush.

Supply water. Set the humidity again as required.

Check your setting humidity. Close the view window again after checking. Initialize the incubator. [Refer to the page 11]

Humidity will notgo high enough.

Egg-Turning fails to work.

Check that the Egg-turning stoppage is not activated. (Egg-turning lamp lighting)

Check that there are no foreign items on the egg turning tray.

Check if egg turning plate is assembled correctly. [Refer to the page 9]

If you need to turn the eggs, you can manually re-start egg-turning.

Unplug the power supply and disassemble the main body for cleaning the egg turning tray and gear.

Assemble egg turning plate as the picture on page 9.

Dew foams inthe incubator.

Check the incubator is not placed too cold circumstances.

When you turn OFF incubator and then turn on.

Move the incubator to where the ambient air temperature is over 28℃ (82.4℉)

Dew condensation is normal. Dry the incubator completely under well ventilated place.

Take out the plug out of the outlet and disassemble the main body and clean around the air circulation fan with brush.

Check if there is any hatching debris such as feather or eggs-shell in the incubator FAN.

The machine makessome noise.- It is normal that the machine emits some sounds because it uses air circulation fan for working.

Check that you have not overfilled the incubator. Check that the incubator placed on inclined

surface. Check if it is Dew condensation

Water leaks from the machine.

Do not fill water over LIMIT indication. Place incubator under a level surface.

Check if room temperature is too high Check if incubator is exposed to the direct

rays of sun

Check if room temperature is too low Check if incubator heater(temperature controlling-

system) is normally working

Adjust room temperature 28℃ (82.4℉) Install incubator without the direct rays of sun Return incubator to factory setting [Refer to page 11]

Adjust room temperature 28℃ (82.4℉) Place thermometer inside of incubator and check

if setting temperature is correct Return incubator to factory setting [Refer to page 11]

If you need detail self diagnosis, please click “self diagnosis” on our website.

Be sure that the incubator works without any problem before placing eggs in the incubator.

6. Product Information (2) Troubleshooting

6. Product Information (3) Specification

1-1 NAME : Rcom MAX 201-2 MODEL NO. : MX-20Specification

Egg-Turning Interval

Temp. limits

Working Temperature Ideal:20 ~ 25[ Min. 15[ / Max. 30[

Power

Humidity Limits

Power Consumption

20.0 ~ 42.0[

AC 100 ~ 120[V], 50/60[Hz]AC 220 ~ 240[V], 50/60[Hz]

20 ~ 70[%] ( It can be changed according to the conditions )

Various according to the tray

Capacity

Net Weight

Size

4.35[kg]

Fuse Standard 250[V] 2.0[A] ( 5 20[mm])

(W)500 410 160 [mm]

Average. 48[W] MAX. 65[W]

For all size egg

Small Standard Large

:

:::

:

:::

Various sized egg incubation isavailable52 [EA] ( Quail egg size )20 [EA] ( Chick egg size )10 [EA] ( Goose egg size )

(Included)

(option)

(option)

(option)

Universal tray

Small egg trayStandard egg trayLarge egg tray

Register your product Serial No. on our website for free 2 years gurantee. Refer to website for how to register. (Free 1 years gurantee in case not registerd.)

You will be asking for service charge if you are in below cases.1. Broken or Problem caused by ‘No cleaning’ or ‘Improper handling’2. Broken or problem caused by ‘Not using distilled water’3. Broken or problem caused by ‘Trying Bird hatching in incubator’ (Please don’t try bird hatching in incubator. Please use Hatcher during bird hatching.)4. Broken or problem caused by ‘Wrong controling(Using)’5. Broken or Problem caused by using the machine out of User’s Manual.6. Broken or problem caused by ‘Customer’s mistake or fault’

※ Product Registration ProceduresIf you are a new member of Rcom, you need to log in our website at www.Rcom.co.kr1. Click “SIGN UP” on top of the right corner.2. Fill out the information on the blanks.

If you already registered your information on the Rcom website, please log in to www.Rcom.co.kr.1. Click “Login” on top of the right corner.2. Select “Customer” and click “Register Products”.3. Fill out the information on the blanks.

You will need below information to register on our website.1. Your name2. Your (home/company) address & Email address, country3. Your product(model) name & Serial number4. Date of purchase & Name of purchased shop you bought from

Partly spare parts are not on the parts list.

Names of goods(*.Compatible)Image Part No Names of goods

(*.Compatible)Image Part No

H20-F201-10 H20 Body

H20-A202-10 H20 Bottom ASM

H20-F203-10 H20 Slide

H20-A200-10 H20 Window ASM

H20-A218P-10

H20-A218U-10

H20 PRO M ain PCB ASM

H20 M ain PCB USB ASM

H20-A218M -10 H20 M AX M ain PCB ASM

H20-A219-10 H20 SM PS PCB ASM

RCM -A310-10 T H V 2 Sens orASM

H20-F206-10 H20 M ainPCB Cover

H50-H611-10 H50 HumiHeater Cover

H20-A216-10 H20 Humidity Unit ASM

RCM -700-10 Sil icon T ube

K20-H512-10 Heat Support -A

H50-H612-10 Heat Support- B

H20-A234L-10H20-A234H-10

H20 Sil icon 110HEAT ER

ASM H20 Sil icon220HEAT ER ASM

H20-AF212-10 H20 FrontLock ASM

H20-AF211-10 H20 RearLock ASM

H20-F240-10 H20 Air Fin

H20-F229-10 H20 Water Cap

Rcom USB 20, PRO 20, MAX 20 PART LIST

Rcom USB 20, PRO 20, MAX 20 PART LIST

Partly spare parts are not on the parts list.

Names of goods(*.Compatible)Image Part No Names of goods

(*.Compatible)Image Part No

H20-F237-10(Option)

H20 Brooding T ray(*For reptileincubator)

H20-F210-10 H20 Univers alT ray

H20-F233-10 ABSDivider(No.2)

H20-F234-10(option) H20 Roller

Divide

H20-F208-10 H20 StandardT ray

H20-F207-10 H20 Large T ray

H20-F209-10 H20 Small T ray

H20-F219M -10(R90-F219M -10)

H20 M AX M embrane SW(R90 M ax type)

H20-F219P-10(R90-F219M -10)

H20 PRO M embrane SW(R90 Pro type)

H20-F224-10 H20 Pinion Gear

H20-F223-10 330 Geard M otor

H20-F214-10 Humi BLDC FAN40

H20-F226-10 BLDC FAN50

H20-304XX-10 Pow er Coard(8)

H20-H686-10 H20 Rubber Foot

H20-F239-10 H20 Sty rofoam Ball

H20-F244-10(Option) H20 Hatching Pad

RCM -347-10 USB Cable

Rcom PRO MINI (PX-03)

Rcom MAX 20 (MX-20) Rcom PRO 20 (PX-20)

Rcom KINGSURO MAX 20 (MX-SURO)

Rcom reptiles MAX 60 (MX-R60)Rcom reptiles PRO 90 (PX-R90)

Rcom Incubator Series

Rcom reptiles MAX 60 (MX-R60)

PUMP POWERPOWER INLET

Rcom BROODER&ICU(MX-BS500(N))

Rcom DIGILOG(PX-V1)

Rcom DIGILOG2(PX-V2)

Rcom MAX 50 (MX-50) Rcom PRO 50 (PX-50)

PUMP POWERPOWER INLET

WATER

PULL OPEN

WATER

PULL OPEN

SELLER

www.Rcom.co.kr

MANUFACTURER