Upload
others
View
17
Download
0
Embed Size (px)
Citation preview
plat
e
Guide only
Find centre of
door and mark
ready for drilling
25mm latch hole.
1
Door and latch preparation templateImportant NoteDrill hole from both sides of door
to prevent splintering of door face.
Fold
her
e on
doo
r edg
e Tem
plat
e
CL
INSTALLATION OF PASSAGE AND PRIVACY SET
Internal Door Furniture
VELOCITY Internal Door Furniture
R
SRZ Internal Door Furniture
32MM - 45MMDOOR THICKNESS
TM
Mark hole positionready for drilling 2x10mm screw holes.
3
Mark hole position readyfor drilling 16mmfurniture hole.
2
Backset 60mmMark hole positionready for drilling 1x 10mm privacy pin hole. (privacy lever set only)
4
Door and latch preparation template
Important NoteDrill hole from both sides of door to prevent splintering of door face.
Fold
her
e on
doo
r edg
e
Tem
plat
e
CLCut along dashed line
INSTALLATION OF PASSAGE AND PRIVACY SET Internal Door Furniture VELOCITY Internal Door Furniture
R
INSTALLATION OFPASSAGE AND PRIVACY SET
Guide only
32MM - 45MMDOOR THICKNESS
Fold here on door edge
Q50094 1112
Mark hole positionready for drilling 2x10mm screw holes.
3
Mark hole position readyfor drilling 16mmfurniture hole.
2 Find centre of door and mark ready for drilling25mm latch hole.
1
Door preparation and latch installation (steps 1- 9)
Insert latch into 25mm hole.
Mark around latch faceplate and chisel out recess.
Face plate must be flushwith door face.
4
Mark line on the door faceapprox 1000mm from the floor.Cut along - - - dashed line.Fold page on door edge.
Align CL on template withmarked line on door face.
Find centre of door and markready for drilling 25mm latch hole.
Mark hole position ready fordrilling 16mm furniture holeboth sides of door.
Drill 2mm pilot hole for the furniture both side of door.
Insert latch with the curved side of the latch bolt facing in the direction that the door closes.
PRIVACY LATCH ONLY
To reverse the privacy latch bolt handing (for doors thatopen outwards).
Remove the circlip and assemble to opposite side.
Drill 2x 2mm pilot holesand affix screws provided.
Set circlipposition on the exteriordoor side.
Privacy pin on the interiordoor side.
Latchbolt
Circlip
Backset 60mm
2 3 4 5
6 7 8 9
12
3
1 Drill 25mm latch hole todepth of 80mm, ensure holeis drilled squarely.2 Drill a 16mm furniture hole,
Mark hole positionready for drilling 1x 10mm privacy pin hole. (privacy lever set only)
4
4
3 & 4 Drill 3x 10mm holes, from both sides of door to prevent splintering.
Guide only
Find centre of
door and mark
ready for drilling
25mm latch hole.
1
Door and latch preparation templateImportant NoteDrill hole from both sides of door
to prevent splintering of door face.
Fold
her
e on
doo
r edg
e Tem
plat
e
CL
INSTALLATION OF PASSAGE AND PRIVACY SET
Internal Door Furniture
VELOCITY Internal Door Furniture
R
SRZ Internal Door Furniture
32MM - 45MMDOOR THICKNESS
TM
Mark hole positionready for drilling 2x10mm screw holes.
3
Mark hole position readyfor drilling 16mmfurniture hole.
2
Backset 60mmMark hole positionready for drilling 1x 10mm privacy pin hole. (privacy lever set only)
4
1
Tem
Guide
Find centre of
door and mark
ready for drilling
25mm latch hole.
1
Door and latch preparation templateImportant NoteDrill hole from both sides of door
to prevent splintering of door face.
Fold
her
e on
doo
r edg
e Tem
plat
e
CL
INSTALLATION OF PASSAGE AND PRIVACY SET
Internal Door Furniture
VELOCITY Internal Door Furniture
R
SRZ Internal Door Furniture
32MM - 45MMDOOR THICKNESS
TM
Mark hole positionready for drilling 2x10mm screw holes.
3
Mark hole position readyfor drilling 16mmfurniture hole.
2
Backset 60mmMark hole positionready for drilling 1x 10mm privacy pin hole. (privacy lever set only)
4
Face plate
55mm Rose
INSTALLATION OF PASSAGE AND PRIVACY SET Internal Door Furniture VELOCITY Internal Door Furniture
R
INSTALLATION OFPASSAGE ANDPRIVACY SETS
32MM - 45MMDOOR THICKNESS
Q50094 1112
10 11 12 13 14
Passage and Privacy set installation (steps 10 - 21)
Strike preparation and installation (steps 22 - 27)
15 16 17 18 19
20 21
22 23 24 25 26
27 5
Position lever assembly (side with screws) so that it operates downward to retract the latch bolt.
Align spindle into the squareopening in latch, screws pass through screw holes.
Locate opposite lever(side without screws), alignscrew heads through large screw holes in furniture.
Rotate rose furniture toalign screws with countersunkholes.
Lightly tighten fixing srews.Check levers are horizontaland in line with the latch.Then firmly tighten fixing screws.
Pass trim over lever.Push trim to secure.Position removal tab to the bottom.
PRIVACY SET ONLYOn the exterior side of dooralign emergency access holeson trim and furniture.
PRIVACY SET ONLYScrew in the privacy buttonon the interior side of doorthrough hole in trim.
PRIVACY SET ONLYDepressing the privacybutton will lock the (exterior)outside lever.
PRIVACY SET ONLYRotate (interior) insidelever to release privacy lock.
PRIVACY SET ONLYInsert and push pointed tool to gain access from the (exterior) outside when the privacy button is engaged.
Partially close door.Mark centre of latch bolt.Mark horizontal line along the inside face of the doorjamb.
Measure the door thicknessand halve it.
From the door stopalong the horizontal line,measure and mark a verticalline at half the door thickness.
At this point drill 25mm hole,13mm deep into the doorjamb.
Align strike plate centrallyand vertically over this hole.Mark around plate.Chisel out jamb to allowstrike plate to sit flush.
Drill 2x 2mm pilot holes andaffix screws provided.
Door stop
FOR OUTWARD OPENING DOORS
REFER TO STEP 7 & 8.
Emergencyaccess hole
PRIVACY SET (displayed)Parts and assembly
DO NOT REMOVE SCREWS
Privacy button
*
Removal tab
55mm Rose