Download Technical Specifications & BOQ

NATIONAL CENTRE FOR SUSTAINABLECOASTAL MANAGEMENTANNA UNIVERSITY, CHENNAI

VOLUME 2OF TENDER DOCUMENTS

BILL OF QUANTITIES FOR PROPOSED INTERIOR LAYOUT

AND TECHNICAL SPECIFICATIONS FORFFLOORING, CARPENTRY, GLAZING,

FABRICATION WORKS, PAINTING, SUSPENDED FALSE CEILING,MODULAR FURNITURE, POWDER COATING

Project : Interiors for NCSCM @ ChennaiOwner : NCSCM

abc

d

efg

h

Notes:

1a.

b.c.

d.

e.

f.

g.h.I.j.k.l.

m.

n.o.p.

q.r.s.

With respect to any brans / makes specified in this document, Contractor is permitted to quote for equivalent brand / make and is to provide details of the same.

The contractor is to note and allow the following preambles in his scope of work.

Timber used shall be kiln seasoned and should be free from shrinkage, warpage even after fabrication of furniture.

For partition anchoring on floor & true ceiling : 75/10 no. sheet metal screw 75mm in length.

All exposed veneer shall be group matched natural cut plain veneer of approved make and shade.

Provision to be made for additional supports and reinforcement that may be required for stability and evenness at where curved partition isconstructed.

Contractor to make provisions of all necessary scaffoldings to facilitate high level installations.Contractor to form openings on partition for services and to seal gaps using silicon sealant.

All exposed vertical laminated surfaces shall be finished with 1.0mm thick laminate of approved make shade unless otherwise specified.

Contractor to use the following screws unless otherwise specified.For partition frame work : 16/8 no. sheet metal screw 16mm in length.

All plywood, blockboard for office areas shall be water resistant, termite/borer proof commercial grade of specified make.All plywood, blockboard for wet areas (toilets/pantry) shall be termite/borer proof and waterproof marine grade of specified make.

Where the use of spring loaded auto closing hinges is specified, the same shall be installed strictly as per manufacturers guidelines and relevanttools required for the same.

All items to have sample approved prior to commencement of mass production.All screws seen out side should be star SS.

Special attention to be paid to Technical specifications.Basic rate shall not include all taxes, delivery, handling charges, wastage & delivered at site.

All exposed veneered, wood surfaces shall be finished with matt melamine polish to approved shade.All exposed edges of plywood, blockboard etc shall be finished with 3mm thick lipping beading of specified wood.

Unless otherwise specified the rates quoted shall be inclusive of the following ~ Cost of material, taxes, transport, labour, overheads and profit &complete finishing etc.,

All internal woodwork shall be treated with anti termite and fire retardant paintAll internal surfaces of cabinets, etc in conventional carpentry works shall be finished with 0.8mm thick matt finished laminate of approvedshade

All under surfaces of furniture (tables, counters, etc) to be finished with 0.8mm thick matt finished laminate of approved shade

All exposed horizontal laminated surfaces shall be finished with 1mm thick laminate of approved make shade unless otherwise specified.

Contractors should factor in their prices for power and water etc. Space will be provided at site for stores but contractor will be responsible for and maintenance of the same.

CARPENTRY, JOINERY WORKS

GENERAL NOTES COVERING BILL OF QUANTITIES

Rates quoted must have full compliance with the following including the cost of grey cement, and white cement.The owner reserves the right to supply or issue price basis for any material item.The owner reserves the right to 'lend' his name for all imported items in order to avail any possible duty exemptions and the said benefit shall goto the owner.The items which are supplied free of cost need to be reconciled at the end of the project based on material constants.

1 RC Design Pvt.Ltd


GENERAL NOTES COVERING BILL OF QUANTITIES

2a.

b

c.

d.

e.

f.

g.

h.I.

j.

k.l.m

nopqrs In the instance of granite/marble floors, the contractor has to obtain prior approval on dry laying. Wet laying to be carried out only on approval.

Not extra cost shall be paid for dry laying.

Pointing to be done using matching coloured grout as specified/directed.All marble flooring/slabs to be polished using tin oxide only.Slurry for marble flooring to be of white cement only.

Base sub-grade/sub-floor to be prepared by cleaning all dust/loose particles, caked mortar droppings, etc by scrubbing with steel wire brushes.Surface to be roughened if so required and surface cleaned with water and kept wet for minimum 12 hours.

Bedding layer of mortar to be provided as directed in the case of 19mm+ slabs to correct level, step as instructed.Finished work to be inclusive of cutting and polishing where specified/applicable.Contractor to be responsible for hiring/operating of all machines/equipment. Approval to be obtained from Project Management consultantbefore operating.

Finished floor must be cured by keeping wet for atleast 1 week after installation.Flooring to be cleaned, waxed or acid washed where applicable and as directed.

If there is a reduction is the basic rate the cost for the same shall be adjusted pro rata in the quoted rates. No increase in basic rates shall beallowed without written approval from the Architect.

For fixing metabox drawer channel : 9.5/6 no. sheet metal screw.For fixing auto closing hinge : 16/6 round philip head screw.FLOORING WORKSReceiving all materials supplied by the Owners / your vendors, unloading, storing at location specified by the project manager. No additionalpayment will be paid for any increase lead from this location conveying to work site & fixing in position. (If any materials supplied by Owner).

All finished flooring shall be covered with plaster of Paris of 6mm thick over a plastic film without any extra cost till handing over to the Owner.

Daily housekeeping of work areas which includes segregation of debris like cement based, plastic, glass, wood and collecting in containersprovided to/by you, at an acceptable location inside the site premises.

Granite slabs should be free of all defects and all grains / patterns shall be properly matched from the same lot. Any colour / lot variation shallbe rejected.

The minimum quality benchmark will be decided by the Owner / Project management consultant / Architect based on mock up samplesbefore commencing the work.

Unless otherwise specified the rates quoted shall be inclusive of the following ~ Cost of material, taxes, transport, labour, overheads and profit,etc.,

For fixing door hinges : 30/8 no. Philip head SS screw.

The basic rate of granite/marble includes supply, taxes and delivery to site, delivered and unloaded to the point of cutting, the same. All granite material shall be "gang saw water cut".

No wastages shall be paid for seperately. The same shall be factored in the quoted rate.

For fixing drawer channel : For bottom channel - 19/6 no., For side - 9.5/6 no. sheet metal screw.

For 6mm thick ply panelling 19/6 no. sheet metal flat head screw, 12mm thick ply panelling 25/8 no. sheet metal flat head screw, for 19mm thick ply panelling 32/8 no. sheet metal screw.

2 RC Design Pvt.Ltd


SL.NO. ITEM DETAILS VENDORS CONFIRMATION

Note:The following is the list of approved make/brand against each product. Where more than one brand has been specified, the names are given in order of preference. Contractor is to quote rates based on the materials of 'first preference' after ascertaining availability, delivery schedules and other parameters affecting delivery. Unless the Contractor stipulates to the contrary in his tender, it shall be assumed that the rates quoted are for materials of first preference.

APPROVED MAKES OF MATERIAL

1 TIMBER AS APPROVED ( BASIC RATE = Rs. 2000/- PER CFT )

2 PLYWOOD COMMERCIAL GRADE

CENTURY

ARCHID PLY

GREEN PLY

APPROVED EQUIVALENT

3 PLYWOOD MARINE GRADE

CENTURY

ARCHID PLY

GREEN PLY

APPROVED EQUIVALENT

4 MDF Both Exterior and Interior Grade

NUWUD

DURATUFF

ASIS

APPROVED EQUIVALENT

3 RC Design Pvt.Ltd


5 DECORATIVE LAMINATES

GREENLAM

MERINO

ARCHID

APPROVED EQUIVALENT

6 WOOD VENEER TIMEX

JACKSON

URO

APPROVED EQUIVALENT

7 SOFTBOARD CELOTEX OR APPROVED EQUIVALENT

8 GLASS, MIRROR MODIFLOAT

ASAHI

SAINTGOBAIN

APPROVED EQUIVALENT

9 HERMETICALLY SEALED DOUBLE GLAZING

IMPACT SAFETY GLASS

GSCTOUGHENED GLASS, NOIDATUFFGLAZE INDIA Pvt Ltd, NAVI MUMBAI

10 ACRYLIC EMULSION PAINT

ICI

ASIAN

APPROVED EQUIVALENT

CENTURY

BERGER

4 RC Design Pvt.Ltd


ASSABLOY

11 SYNTHETIC ENAMEL ICI

ASIAN

APPROVED EQUIVALENT

12 TEXTURED PAINT OIKOS

SPECTRUM HERITAGE

APPROVED EQUIVALENT

13 AUTOMOTIVE PAINT DUCO

ICI

APPROVED EQUIVALENT

14 ANTI-TERMITE PAINT WOOD CARE

WOOD GUARD

APPROVED EQUIVALENT

15 MELAMINE POLISH MRF

LIGHT HOUSE

SHEENLAC

APPROVED EQUIVALENT

16 PATCH FITTINGS DORMA

GEZE

APPROVED EQUIVALENT

BERGER

5 RC Design Pvt.Ltd


ASSABLOY

17 FLOOR SPRING DORMA

APPROVED EQUIVQLENT

GEZE

18 FLOOR SPRING FOR OTHER DOORS

DORMA

APPROVED EQUIVQLENT

GEZE

ASSABLOY

19 EXPOSED DOOR CLOSER

DORMA

GEZE

APPROVED EQUVALENT

APPROVED EQUVALENT

20 BEARING HINGES UNION

HAFELE

APPROVED EQUVALENT

21 MORTISE HANDLE DORMA

GEZE

ASSABLOY

ASSABLOY

6 RC Design Pvt.Ltd


APPROVED EQUVALENT

APPROVED EQUIVALENT

22 DEAD LOCK DORMA

GEZE

23 MORTISE LOCK CYLINDER

DORMA

GEZE

UNION FB 10 SS

DORMA

GEZE

KICH IB 106 SSTOILET DOOR INDICATOR BOLT

27

APPROVED EQUIVALENT

ASSABLOY

DORMA 20mm DIA 450MM LONG "D" TYPE HANDLE

PATCH DOOR HANDLE24

ASSABLOY

ASSABLOY

GEZE 20mm DIA 450MM LONG "D" TYPE HANDLE

ASSABLOY 20mm DIA 450MM LONG "D" TYPE HANDLEAPPROVED EQUIVALENT

APPROVED EQUIVALENT

FLOOR MOUNTED DOOR STOPPER

25

APPROVED EQUIVALENT

CONCEALED TOWER BOLT

26

7 RC Design Pvt.Ltd


CABINET HANDLES KICH96mm CHH 84 S OR APPROVED EQUIVALENT

SCREWSJOINERY WORKS NETTLEFOLD IS 1365, GI

screws

HARDWARE, FITTINGS SS STAR HEAD SCREW AS PER MANUFACTURERS SPECIFICATION

APPROVED EQUIVALENT

GEZE

28 MULTI-PURPOSE LOCK DORSET MP 300 SS WITH 3 KEYS OR APPROVED EQUIVALENTEBCO

29 CABINET HINGE (AUTO CLOSING)

30 DRAWER SLIDE SYSTEM (TELESCOPIC CHANNEL)

EBCO OR APPROVED EQUIVALENT

HAFELE

DORMA

DAZ

APPROVED EQUIVALENT

AUTO DOOR BOLT31

32

U FOAM

KURLON

35 VITRIFIED TILES KAJARIA

NITCO

ASIAN

APPROVED EQUIVALENT

FOAM RUBBER34

33

8 RC Design Pvt.Ltd


APPROVED EQUIVALENT

36 SILICON SEALANT DOW CORNING

APPROVED EQUIVALENT

ULTRAMARK

APPROVED EQUIVALENT

APPROVED EQUIVALENT

FROSTED FILM

BIRLA WHITE

BIRLA 3M

LUMAR

ALUCOBOND

TIMEX BOND

COMPOSITE ALUMINIUM INTERIOR GRADE ( 3MM THICK )

39

KIMCO

40 FABRIC AS PER APPROVED SAMPLE ( BASIC RATE Rs.200/- PER RMT. )

DORMA

HAFELE

ROCKWOOL

UP TWIGA

APPROVED EQUIVALENT

WHITE CEMENT37 JK WHITE CEMENT

38

APPROVED EQUIVALENT

FIBRE GLASS WOOL41

42 110 DEG OPENING AUTO CLOSING HINGES

9 RC Design Pvt.Ltd


APPROVED EQUIVALENT

43 OIL BASED DISTEMPER ASIAN

BERGER

ICI

44 STAINLESS STEEL SAIL STEEL 304 GRADE

APPROVED EQUIVALENT

45 ANTI-STATIC VINYL FLOORING

ARMSTRONG

LG

APPROVED EQUIVALENT

46 VINYL FILM FOR CLADDING

3M

APPROVED EQUIVALENT

47 ALUMINIUM SECTIONS JINDAL

INDAL

APPROVED EQUIVALENT

APPROVED EQUIVALENT

PALLADIO

48 GI SECTION FOR PARTITIONS & FALSE CEILING

INDIA GYPSUM

LAGYP

APPROVED EQUIVALENT

49 GLASS MOSAIC TILE ITALIA

DIAMOND FRAMES

GEZE

10 RC Design Pvt.Ltd


ULTRATECH

CORAMANDLE

APPROVED EQUIVALENT

BIRLA

50 CEMENT - 53 GRADE

51 RMC ULTRATECH

ACC

CORAMANDLE

APPROVED EQUIVALENT

52 STEEL -TMT TATA

JINDAL

SAIL

APPROVED EQUIVALENT

53 STEEL - STRUCTURAL TATA

JINDAL

SAIL

APPROVED EQUIVALENT



SL.No. DESCRIPTION OF WORKS AMOUNT IN RS.

A INTERIOR FITOUT SCOPE

1.00 CIVIL AND INTERIOR

2.00 MODULAR GLASS PARTITION SYSTEM

3.00 MOD. GRID CEILING

4.00 CARPET

5.00 KITECHEN EQUPMENTS

6.00 LOOSE FURNITURE

7.00 MODULAR WORKSTATION

8.00 CHAIRS

9.00 BLINDS

10.00 SIGNEAGE

GRAND TOTAL IN RUPEES EXCLUDING TAX

Add Vat @ _____% on ______%

Add Service Tax @ ______% on _____%

GRAND TOTAL IN RUPEES INCLUDING TAX

GRAND SUMMARY SHEET



SL.No. DESCRIPTION OF WORKS AMOUNT IN RS.

A INTERIOR FITOUT SCOPE

1.00 FLOORING

2.00 FALSE CEILING

3.00 PARTITION

4.00 DOORS


6.00 WALL FINISHES

7.00 MISCELLANEOUS WORKS

8.00 CIVIL WORKS


Add Vat @ _____% on ______%


GRAND TOTAL IN RUPEES INCLUDING TAX

SUMMARY SHEET



Sl.no Description Unit Total Qty Rate Amount REMARKS

1.00 FLOORING

1.01 CHIPPING OF SCREEDChipping of the existing screed avg tkness 20mm - 40mm to take the flooring Cost to include carting of thedebris from the site

sqmR/o

1.02 CERAMIC TILE FLOORING sqm R/o

Providing and laying vitrified tile flooring over 1:4 cement mortar set in cement slurry. Joints between tiling to be filled with approved grout of approved shade as per manufacturers specifications. Rate to include cost for laying tiles to approved pattern, design as directed by Architect, including curing, acid wash, etc.

Quoted rate to include the cost of curing, protection with polythene sheet and POP overlay till hand-over.

Quoted rate to include the cost of Chipping and removing the Existing Flooring , along with shifting the Debris from Site

Consider basic rate of Ceramic Tile at Rs.485/Sqm.(excluding tax).

Mode of Measurement : Laid area will be measured for payment.

1.03 CERAMIC TILE DADOOING sqm 214.00 Providing and laying ceramic tile flooring over 1:4 cement mortar set in cement slurry. Joints between tiling to be filled with approved grout of approved shade as per manufacturers specifications. Rate to include cost for laying tiles to approved pattern, design as directed by Architect, including curing, acid wash, etc.

Consider basic rate of Ceramic Tile at Rs.485/Sqm.(excluding tax).

Mode of Measurement : Laid area will be measured for payment.

1.04 ALUMINIUM SKIRTING Rmt 550.00 Providing & fixing 50mm ht. anodised approved extruded aluminium skirting fixed over masonry wall /opaque partition to proper line & level. The installed skirting shall be provided with approved matchig colour PVC capping, Complete as per manufacturer's specification, installation guidlines & instructions of the Architect.

(Basic cost of the Al skirting to be considered at 325/rmt including tax, including installation

1.05 SS TRANSITION STRIP Rmt 35.00 Providing and fixing SS Transition strip at junction of carpet and granite floor, carpet and vitrified floor etc., , edge buffing and fixing complete. As per the following specification.

IMAGES ARE JUST FOR REFERNCE. THE SCOPE OF WORK WILL BE AS PER THE SPECS

AND DWGS

BILL OF QUANTITIES FOR INTERIOR FIT OUT

PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai DATE : 12.12.2013




SUB TOTAL CARRIED TO SUMMARY

2.00 FALSE CEILING

2.01 GYPSUM FALSE CEILING sqm 1,845.00

Providing and fixing Suspended False Ceiling which includes Gypsum Plaster board 12mm thk., False Ceiling on 24 gauge G.I. frame work which includes Providing. & fixing G.I. perimeter channels 0.55 mm thk 20mmx30mm,web size 27mm along perimeter of ceiling, screw fixed to brick wall/partition with nylon sleeves & screws @ approx 2'0" c/c. Suspending G.I. intermediate channels size 45 mm,0.9 mm thk, flanges of size15mm each from the soffit 1220mm c/c with ceiling angle 25 x10mm x 0.55mm thk fixed to soffit G.I. cleat & steel expansion fasteners.

Ceiling section of 0.55mm thk having web of 51.5mm & flanges 26 mm each lips 10.5 mm fixed to intermediate channel with connecting clips & perpendicular to int channel @ 457mm c/c.12.5 mm tapered edge Plaster board ( IS 2095-1982 ) screw fixed to ceiling section with 25mm dry wall screws @ 230 mm c/c. Boards to be joint & finished so as to have flush look including filling finishing edges with jointing compound paper tape/cloth gauze & 2 coats of primer suitable for plaster board. Rate to include M.S.framing around A/C ducts where ever necessary.

Rate to include cove to profile, cut-outs for light fixtures, spot lights, smoke detectors, Pelmets, Vertical risers as shown in dwg. and all services cut outs as required. complete as directed by Project manager / Architect.Note: for Light fittings, Grills, diffusers and other cut-outs have to be made with a frame of perimeter channels of size 20mm x 27mm x 30mmx 0.55mm thk, supported suitably. Quoted rate shall also to include the Engineered system made up of primary sections in galvanized steel of 21x35x3600mm in 0.75 bmt gauge. with top cross rails and the system shall be used at 1200mm apart where direct suspenders cannot be used due to over head ducting or any other services.

Mode of measurement : Finished plan ceiling area shall be measured for payment. Any vertical height upto 450mm to be included with the scope which wont be calculated seperately

2.02 LAMINATE CEILING sqm R/oProviding & fabricating Laminate ceiling formed using 25mm X 25mm MS work & vertical support system formed out of M.S angle supports provided at 600mm C/C suspended from the true ceiling. The frame work shall be clad with 19mm thick Ply finished with 1mm thk approved Laminate as per the detailed dwg or the instructions of the Architects. Rate to include 5mm thk '' U '' grooves as per the design.

Mode of measurement : ceiling plan area shall be measured for payment.


3.00 PARTITION

3.01 G.I FRAME WORK - 50mm sqm 950.00 Providing & fixing G.I. frame work for partitions with verticle members at 600mm C/C formed out of 37.5mm X 50mm thick G.I sections of Gypsum India make with horizontal member at the floor & soffit complete as per detail dwg. & manufacturers specification.

Contractor to make provision for fixing all electrical, networking boxes formed out of 12mm thick ply boxing screwed onto partition framework at required heights/levels as directed.

Mode of measurement : Length & height (upto true ceiling) shall be measured for payment.




3.02 ALUMINIUM PARTITION Sqm 15.00 Fabricating and fixing partition frame work consisting of 50mm x 25mm x 1.2mm (with 0.581Kgs / Rmt as per ISStandards of Jindal or equivalent make) thick extruded aluminum box section framework at spacing notexceeding 600mm both ways (horizontal and vertical). Framework formed using 50mm x 25mm x 1.2mm thickextruded aluminum box section connected using 50mm X 25mm X 1.2mm thick "L" angle support cleats fixedwith 12mm galvanized metal screws. Partition framework to be secured to floor, structural support and neareststructural member using galvanized metal screws and wooden dowels.

Contractor to make provision for all electrical, networking boxes which shall be installed on 25mm x 25mm x1.2mm thick extruded aluminum "L" angle screwed onto partition framework at required heights/levels asdirected.

Mode of measurement : Length & height ( up to true celing ) shall be measured for payment.

3.03 12mm THICK MDF SKINNING sqm 626.00 Providing & fixing 12mm thick MDF skinning on existing aluminum frame work using 19mm screws at every 300mm center to center. The MDF skinning is finished using approved metal putty & primer as per detail dwg.

Mode of measurement : Length & height shall be measured for payment.

3.04 12.5mm THICK GYPSUM SKINNING. sqm 1,901.00 Providing & fixing 12.5mm thick taper edge gypsum skinning on existing aluminum frame work using propriety supplied screws at every 300mm center to center. The gypsum skinning is finished using proprietary supplied jointing tape & jointing compound as per manufacturer's specification.

Quoted rate shall include providing 12mm X 25mm Aluminum L-Angle & grooves where ever necessary as per detail dwg.


3.05 CURVED GYPSUM SKINNING sqm R/oProviding & fixing 12.5mm thick tapered edge gypsum skinning for curved partitions on existing partition frame work using proprietary supplied screws at every 600mm center to center. The gypsum skinning to be finished using proprietary supplied jointing tape & jointing compound as per manufacturer's specification.


3.06 12MM COMMERCIAL PLY SKINNING sqm 40.00 Providing & fixing12mm commercial ply skinning for partitions on existing partition frame work using proprietary supplied screws at every 600mm center to center. The skinning to be finished using proprietary supplied jointing tape & jointing compound as per manufacturer's specification.

Mode of measurement : Length & height shall be measured for payment. Location : For floating Storage claddingConsidered basic price for ply = 44/Sqft ( excluding taxes )

3.07 6MM COMMERCIAL PLY SKINNING sqm R/oProviding & fixing 6mm commercial ply skinning for partitions on existing partition frame work or on the existing ply backing using proprietary supplied screws at every 600mm center to center. The skinning to be finished using proprietary supplied jointing tape & jointing compound as per manufacturer's specification.

Mode of measurement : Length & height shall be measured for payment. Location : Writing board

3.08 ROCK WOOL INSULATION sqm 950.00 Providing & fixing 50mm thick Rock wool insulation having a density of 32Kg/CMT for opaque partitions as per detail dwg. Cost to include Plastic cover wrapping .


3.09 GLASS PARTITION sqm 23.00 Fabricating & providing full height glass partition from FFL to 2400mm ht. level formed out of 10mm thick clear toughened glass fixed at flooring level using 16mm x 25mm x 1.2mm thick SS "C" Channel. The void in the SS channel to be filled with approved silicon sealant as per detail dwg. The glass to be fixed to the gypsum partition at false ceiling level using 32mm X 12mm thick MDF beading finished in approved automotive paint.

Contractor to polish / chamfer the edges of the glass & seal the joints between glass with clear silicon sealant. The cost to include providing & Fixing frosted film to the glass as per the design of the Architect's.

Mode of measurement : Length & height up to False ceiling shall be measured for payment.




3.10 VENEER PANELLING sqm 270.00 Providing & fixing veneer paneling formed out of 4mm thick approved veneer fixed over 12mm thick MDF and to be finished in melamine polish, with 6mm SS strips as per the design complete as per instruction of the Architect's.


Consider Basic cost of Veneer @ Rs. 1400/sqm Note : Factory Finished & Polished with Clip on System will be preferred.

3.11 LAMINATE PANELLING sqm R/oProviding & fixing laminate panelling formed out of 1mm thick laminate pressed over 4mm MDF fixed over existing commercial ply/ MDF boxing on all exposed surfaces , complete as per instruction of the Architect's.

Cost to include provididng and fixing 6mm Aluminium "U"Channel @1200mm interval as per the drawing and instructions of the Architect

Mode of measurement : Length & height up to False ceiling shall be measured for payment.Note : Factory Finished with Clip on System will be preferred.Consider Basic cost of Laminate @ Rs. 290/sqm

3.12 WALL PAPER PANELING sqm R/oProviding & fixing approved wall paper paneling over existing gyp/ply partition with necessary surface preparation for receiving the wall paper complete as per detail dwg. & Architect's instruction. Consider Basic rate of Wall paper as Rs.1500.00 Per sq m

Mode of measurement : Installed wall paper shall be measured in length & height for payment.

3.13 LAMINATED GLASS PANELLING sqm 235.00 Providing & fabricating Glass panelling formed using 50mm X 25mm Aluminium Frame work provided at 600mm C/C . The frame work shall be clad with 8mm thick Laminated glass on existing 12mm thk MDF backing ,complete as per the detailed dwg or the instructions of the Architects. Cost to include the U channels

Consider Basic cost of Laminated Glass @ Rs. 2700/sqm ( Excluding taxes )

Mode of Measurement : Cladded Glass area will be measured for payment.




3.14 PICCOLO CERAMIC TILE sqm 32.00 Providing & fixing Ceramic tile dado of approved make & colour fixed over masonry/partition using solid bed of BALCEM (Polymer modified cementations adhesive) & BAL ADMIX AD1 (Polymer modified liquid). Joints between tiling to be filled with approved grout of approved shade as per manufacturers specifications.

Consider Basic cost of Piccolo Tile @ Rs. 3015/sqm ( Excluding taxes )Mode of Measurement : Cladded tile area will be measured for payment.

3.15 CURVED MDF PANELLING - DUCO FINISHED sqm R/oProviding & fabricating Panelling on ExistingCurved Wooden Frame Work . The frame work shall be clad with 6+6 mm thick Flexi Ply & 4m thk MDF finished with approved Colour Duco Paint . ,complete as per the detailed dwg or the instructions of the Architects.

3.16 ACOUSTIC PANELLING sqm R/oProviding and fixing Acoustic Panels over existing partition / wall with ply backing with required beading on allsides . Thickness: 9 mmDimension: 1200 mm X 2400 mmDensity: 237 kg/m3 (Testing method: ASTM D 1752)Techno Acoustic™ Wall Panel is lightweight and flexible along with excellent tension/compression stiffness.

The tile maintains its dimensions in high humidity and temperature.

The color of the tile maintained even in long term exposure to sunlight (over 4th grade in 240 hrs at 100°C).

The surface of the tile is resistant to surface wetting (rate of resistance to surface wetting: 99.6%) thereforeinhabitation of various germs and molds is inhibited.Furthermore, the panel can be easily cut into any desired shape.

Consider Basic cost of Acoustic Panel @ Rs. 3010/sqm ( Excluding taxes )Mode of Measurement : Cladded area will be measured for payment.

3.17 MIRROR PANELLING sqm 120.00 6mm thick Mirror to be cladded on existing 12mm thk MDF backing ,complete as per the detailed dwg or the instructions of the Architects. Mode of Measurement : Cladded Glass area will be measured for payment.

3.18 MDF JALI WORK PANELLING - DUCO FINISHED Sqm 9.00 Providing & fabricating Jali work Partition made of 25 mm MDF finished in Mettalic Duco paint to be fixed tothe floor and ceiling . ,complete as per the detailed dwg or the instructions of the Architects.

Cost also to include Design and Lazer Cutting on theMDF , and MS supports above False ceiling up to true ceiling .

Mode of measurement : Length & height upto Height of the Jali Work Partition shall be measured for payment.

3.18 MODUALR PARTITION FOR TOILET nos 67.00 Provididng and Fixing Modular Toilet Partition with the following SpecificationModel Type : Top Hung SeriesThickness of Compact Laminate :12 mm ThickSize of Cubicle : 1550mm x 1130mmDoor Size : 800mma) SS Top Railb) Hinges – Gravity to closec) Privacy Thumb turn c/w Occupancy Indicatord) Coat Hooke) Door Knobf) Adjustable legi) Rubber Door Stopper Liningj) Screws & Wall PlugApproved Make : Merino





4.00 DOORS

4.01 SINGLE LEAF SINGLE SWING HONEY COMB FLUSH DOOR WITHOUT FRAME

a) Opening size: D1 - 1000mm X 2400mm ( Location : meeting rooms , trainning rooms, pantry, store, gym , musicetc )(Vision panel - 100 x 950)

nos -

Shutter : Fabricating & fixing single leaf single swing flush door 33mm thk with honeycomb core of 25mm and 4mm prelaminated MDF on both sides of approved make, The shutter edges have a 25 x 75 mm pine wood frame with 6 x 33 mm wooden edge binding

Hardware : one no SS mortise lock of " Dorma /Geze/ Ingersol rand " with , 4nos ss bearing hinges of Haffle/ Union make , 1 no exposed door closure of approved make, one no floor mounted SS door stopper.

Frame : No frame . The shutter to be fixed to the portal with fixing details as shown in the detailed dwgs

4.02 SINGLE LEAF SINGLE SWING FLUSH DOOR WITH FRAME Nos 66.00 a) Opening size: D2 - 1100mm X 2400mm (Vision panel - 100 x 950) Nos 4.00

b) Opening size: D3 - 900mm X 2400mm

Shutter : Fabricating & fixing single leaf single swing flush door 38mm thk of approved make, finished with 1mm thick laminate of approved make & colour on both sides. The shutter edges shall be lipped in 8mm thick approved timber beading melamine polished.

Hardware : one no SS mortise lock of Dorma / Geze / Equiv with , 4nos ss bearing hinges of Dorma/ Geze make , door closure of aproved make, one no floor mounted SS door stopper.

Frame : Frame should be formed out of 50mm X 100mm approved timber melamine polished with 38mm wide x 12mm deep rebate.

Fixing of Frame : Frame should be fixed to masonry wall using M.S holdfast / for partitions using wooden screws with clear anti-termite treatment for the conceled portion frame.

4.03 SINGLE LEAF SLIDING DOOR Nos 18.00 a) Opening size: D2 - 1000mm X 2400mm

Shutter : Fabricating & fixing single leaf single swing flush door 38mm thk of approved make, finished with 1mm thick laminate of approved make & colour on both sides. The shutter edges shall be lipped in 8mm thick approved timber beading melamine polished. the shutters to be fixed with required sliding tracks Dorma/ Geze make

Hardware : one no SS handle from outside and dead latch from inside Dorma/ Geze make ,

4.03 SINGLE LEAF GLASS DOOR WITH FLOOR SPRINGa) Opening size: SD2 - 1000mm X 2400mm nos R/o

Shutter : Providing & fixing glass door mounted over approved Glass Hinges . The shutter to be formed out of 12mm thick clear toughened glass. The glass shutter should be polished on the edges.

Hardware : DORMA Hardware’s like, one no’s floor mounted SS bush of approved make, floor spring(BTS 84 of Dorma make) with spindle of Dorma / approved make. Top patch with pivot of Dorma / approved make, bottom patch with pivot of Dorma / approved make, cost also to include door stopper, complete as per the details and instructions of the Architect.

4.04 DOUBLE LEAF GLASS DOOR WITH FLOOR SPRINGa) Opening size: SD1 - 1800mm X 2400mm nos R/ob) Opening size: SD2 - 2000mm X 2400mm nos - Shutter : Providing & fixing glass door mounted over approved Glass Hinges . The shutter to be formed out of 12mm thick clear toughened glass. The glass shutter should be polished on the edges.

Hardware : DORMA Hardware’s like, two no’s floor mounted SS bush of approved make, floor spring(BTS 84 of Dorma make) with spindle of Dorma / approved make. Top patch with pivot of Dorma / approved make,




4.05 FIRE DOOR

2HR. FIRE RATED DOOR

Opening size: - D11: 1500mm X 2400mm (With vision panel of wired glass of 10mm thk) - Double Leaf nos 1.00 Opening size: - D5 : 1100mm X 2400mm (With vision panel of wired glass of 10mm thk)- - Single Leaf nos 30.00

Providing and fixing in position Fire Rated Metal door with pressed steel frame and shutter as per manufacturer ’s details and as mentioned in the drawings including fixing ironmongery etc of MPP System Schroders make. This includes providing and fixing brush steel finished iron mongery like Ball bearing Hinges, Mortise Locks, Handles, Push Plates, Bolts, Door Closer, etc. (Dorma/ Geze/ Ingersoll /Shakti rand make) as indicated in the detail drawings and all surfaces of doors shall be finished with 2 coats of Fire rating paint over a coat of primer to achieve the fire rating as indicated in the detail drawings.

The door finished Fire retardant polish, steel pressed shutter with 2 Hour Fire rating of Single Shutter and vision panel . Complete as per design and instructions of the Architects.

Complete as per instruction of the Architect's

4.06 METAL DOOR WITH GRILL SHUTTERS Nos 2.00 Opening size: - D11: 1500mm X 2400mm Double Leaf Providing and fixing in position Metal door with grill shutter as per details in the drawings including fixing ironmongery etc. The frame to be made of 100mm x75mm MS box sections The Shutters to be grill which is welded to the Outer frame made of 50mm x50mm MS box sections This includes providing and fixing brush steel finished iron mongery like Ball bearing Hinges, Locks, Handles, Push Plates, Bolts, etc. (Dorma/ Geze/ Ingersoll /Shakti rand make) as indicated in the detail drawings and all surfaces of doors shall be finished with 2 coats of enamel paint over a coat of primer

4.06 ELECTRICAL DB SHAFT DOOR sqm 10.00 Providing & fabricating Electrical DB doors.

Shutter: The shutter of the Electrical trap door to be formed out of 25mm thick commercial ply finished in 1mm thick approved laminate on both sides. The edge of the shutter to be lipped with 8mm thick approved timber beading finished in approved automotive paint.

.

Frame: The frame to be formed out of 50mm X 50mm approved timber finished in approved automotive paint supported with 50mm X 50mm timber frame work from true ceiling.

Hardware: Approved SS butt hinges of approved make, 1no. Duct lock of approved make each shutter, tower bolt of approved make.

4.07 SHAFT DOOR nos R/oProviding & fabricating Shaft doors. - 600 x 2700mmShutter: The shutter of the shaft door to be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate on both sides. The edge of the shutter to be lipped with 8mm thick approved timber beading finished in approved automotive paint.

Frame: The frame to be formed out of 50mm X 50mm approved timber finished in approved automotive paint supported with 50mm X 50mm timber frame work from true ceiling.

Hardware: Approved SS butt hinges of approved make, 1no. Duct lock of approved make each shutter, tower bolt of approved make.Cost to include provididng and fixing 5mm Aluminium "U"Channel in Vertical position as per the drawing and instructions of the Architect



5.01 STORAGE sqm 10.00

Providing & fabricating 450mm deep floating storage formed out of 19mm thick MDF finished in 1mm thick approved laminate consisting of storage with shutter, & 1mm thick approved laminate inside. The shutter of the storage shall be formed out of 19mm thick MDF finished in 1mm thick approved laminate on the external side. with 1mm thick approved laminate on the inside mounted over spring loaded auto closing hinges of approved make, tower bolt. The Storage to accomodate Shelf made of 19mm thk MDF finished with approved laminate as per the dwg .The exposed edges of the storage shall be lipped using approved timber beading formed to shape melamine polished, complete as per detail dwg. & Architects instruction.

Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos. chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos. heavy duty SS ball catch, 100mm C type brushed SS handle

Mode of measurement : Length & height of the storage shall be measured for payment.




5.02 OPEN SHELF STORAGE - LIBRARY sqm 6.00

Providing & fabricating 450mm deep storage formed out of 19mm thick MDF finished in 1mm thick approved laminate consisting of shelves without shutter, & finished with 1mm thick approved laminate on all sides . The storage to have 50 mm recessed skirting The exposed edges of the storage shall be lipped using approved timber beading matching to the laminate, complete as per detail dwg. & Architects instruction.


5.03 PANTRY COUNTER - GRANITE TOP sqm R/oFabricating and fixing low height storage cabinet of height 850mm and depth 750mm formed of 19mm marine grade plywood formwork/carcass and 1 Nos. internal shelf of 19mm marine ply. Shutter of storage unit to be made of 19mm thk MDF finished with 1mm thk laminate The shutter shall be mounted on 3Nos.. of approved spring loaded auto closing hinges of approved make. The rear backing of the storage shall be formed of 8mm thick marine plywood.




Low height cabinet to be topped with 20mm thick approved Granite counter sandwitched at the edge to form a fascia of 40mm thick affixed to carcass with exposed edge profiled full round and polished to high gloss with 1.2mm thick. X 50mm height skirting formed out of 19mm thk marine ply & finished in 1.2mm thick SS brushed finish sheet as per detail dwg.

Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos. chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos. heavy duty SS ball catch, 100mm C type brushed SS handle. Th shutter to be cladded with 6mm thk Toughned Glass with approved colour vinyl Backing with necessary fixture

Consider BasicGranite @ Rs. 2000/sqm


5.04 PANTRY COUNTER - GRANITE TOP sqm 10.00

Fabricating and fixing low height storage cabinet of height 850mm and depth 650mm formed of 19mm marine grade plywood formwork/carcass and 1 Nos. internal shelf of 19mm marine ply. Shutter of storage unit to be made of 19mm thk MDF finished with 1mm thk laminate The shutter shall be mounted on 3Nos.. of approved spring loaded auto closing hinges of approved make. The rear backing of the storage shall be formed of 8mm thick marine plywood.

Low height cabinet to be topped with 20mm thick approved Granite counter sandwitched at the edge to form a fascia of 40mm thick affixed to carcass with exposed edge profiled full round and polished to high gloss with 1.2mm thick. X 50mm height skirting formed out of 19mm thk marine ply & finished in 1.2mm thick SS brushed finish sheet as per detail dwg.

Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos. chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos. heavy duty SS ball catch, 100mm C type brushed SS handle. Th shutter to be cladded with 6mm thk Toughned Glass with approved colour vinyl Backing with necessary fixture

Consider BasicGranite @ Rs. 2000/sqm

Mode of measurement : Length & height of the storage shall be measured for payment. (Studio Unit )

5.05 OVERHEAD STORAGE sqm 10.00 450mm deep X 600mm ht.Providing & fabricating storage 450mm deep formed out of 19mm thick commercial ply finished in 1mm thick approved laminate on both side. The shelves of the storage shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate mounted over SS adjustable pins. Shutter of storage unit to be of Hettich Glass shutter approved colour Vinyl backed with frame Code no : 2-0033 mounted using approved clip-on hinges of approved make, complete as per detail dwg. Architect's instruction. (Studio Unit )

5.06 CONFERENCE ROOM STORAGE sqm 11.00 Providing & fabricating veneered storage 450mm depth formed out of 19mm thick commercial ply finished in 1mm thick approved Veneer on the external side, on the internal side using 1mm thick approved laminate. The storage shall be provided with shelve formed out of 19mm thick approved laminate finished in 1mm thick approved laminate, edges of the shelves shall be finished in 1mm thick approved laminate. The shelves of the storage shall be mounted using approved SS adjustable pins. The shutter of the storage shall be formed out of 19mm thick commercial ply finished in 4mm thick approved veneer on the external side with 1mm thick approved veneer on the inside mounted over spring loaded auto closing hinges of approved make, tower bolt. The exposed edges of the storage shall be lipped using approved timber beading formed to shape melamine polished, complete as per detail dwg. & Architects instruction. 450mm ht Floating storage to be supported on

5.07 FULL HEIGHT STORAGE sqm 285.00

Providing & fabricating laminated storage 600mm depth formed out of 19mm thick commercial ply finished in 1mm thick approved Laminate on all the external sides, and finished on the internal side using 1mm thick approved laminate. The storage shall be provided with shelve formed out of 19mm thick approved laminate finished in 1mm thick approved laminate, edges of the shelves shall be finished in 1mm thick approved laminate. The shelves of the storage shall be mounted using approved SS adjustable pins. The shutter of the storage shall be formed out of 19mm thick commercial ply finished in 1mm laminate of approved colour on the external and inside surfaces , mounted over spring loaded auto closing hinges of approved make, tower bolt. The exposed edges of the storage shall be lipped using approved timber beading formed to shape melamine polished. The storage supported on SS legs ,. complete as per detail dwg. & Architects instruction. Ht= 1200mm

5.08 FULL HEIGHT STORAGE- OPEN SHELF - LIBRARY sqm 270.00




Providing & fabricating laminated storage 450mm depth formed out of 19mm thick commercial ply with open shelves. All the Shelves and internal surfaces to be finished in 1 mm tk laminate . Both outer exposed vertical sides of the storage to be finished in 4mm thick Veneer and all other exposed external surafgaces to be finished in 1 mm laminate The storage shall be provided with shelve formed out of 19mm thick approved laminate finished in 1mm thick approved laminate, edges of the shelves shall be finished in 1mm thick approved laminate. The shelves of the storage shall be mounted using approved SS adjustable pins. The exposed edges of the storage shall be lipped using approved timber beading formed to shape melamine polished. complete as per detail dwg. & Architects instruction. Ht=2400mm . The storage to have sharing intermediate vetical wall.

5.09 OVERHEAD STORAGE FOR REPRO sqm 19.00 450mm deep X 750mm ht.

Providing & fabricating storage 450mm deep formed out of 19mm thick commercial ply finished in 1mm thick approved laminate on both side. The shelves of the storage shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate mounted over SS adjustable pins. The shutter of the storage shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate on the external side and inside, mounted over spring loaded auto closing hinges of approved make, tower bolt. of approved make, complete as per detail dwg. Architect's instruction.

5.10 REPRO STORAGE sqm 20.00 Providing & fabricating storages 600mm depth of ht 750mm formed out of 19mm thick commercial ply finished in 1mm thick approved laminate. The top shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate, exposed edge of the table shall be lipped using approved timber beading formed to shape melamine polished. The shutter of the storage shall be formed out of 19mm thick ply, finished in 1mm thick approved laminate mounted using Auto closing hinges of approved make. The shutter shall be provided Finger Grooves for opening. The storage shall be provided with shelf formed out of 19mm thick commercial ply finished All internal surfaces to be post laminated with 0.8mm thick matt finished laminate of approved shade. All exposed surfaces (underside, topside to be finished with 1mm thick decorative laminate of approved shade.

Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessary tools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos. chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos. heavy duty SS ball catch, complete as per the drawing / instructions of the Architect.

5.11 UNDER COUNTER STORAGE FOR PANTRY sqm 35.00

450/600mm deep X 850mm ht.Providing & fabricating storage 450mm deep formed out of 19mm thick marine ply finished in 1mm thick approved laminate on both side. The shelves of the storage shall be formed out of 19mm thick marine ply finished in 1mm thick approved laminate mounted over SS adjustable pins. The shutter of the storage shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate on the external side and inside, mounted over spring loaded auto closing hinges of approved make, tower bolt. of approved make, complete as per detail dwg. Architect's instruction.

5.12 MEDIUM HT STORAGE sqm -

450/625mm deep X 1200mm ht.Providing & fabricating storage 450mm deep formed out of 19mm thick commercial ply finished in 1mm thick approved laminate on both side. The shelves of the storage shall be formed out of 19mm thick marine ply finished in 1mm thick approved laminate mounted over SS adjustable pins. The shutter of the storage shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate on the external side and inside, mounted over spring loaded auto closing hinges of approved make, tower bolt. of approved make, complete as per detail dwg. Architect's instruction.

5.13 SLOTTED ANGLE SHELVES Sqm 375.00 Providing & installing Slotted angle storage of 800mm deep X 2100mm ht. with shelves at 420mm center tocenter. Rate to include providing necessary rack panels, screws, hardwares, face plates, corner brackets, otheraccessories etc as detailed in the technical specifications part. The finish shall be of powder coated paint finish.Approved make: Godrej or approved equivalent




5.14 RECEPTION TABLE nos 1.00 Dimensions: 3600mm X 750 mm X 1050mm ht.

Table top: Table top of 750 mm wide to be formed out of of 19mm thick commercial ply clad with 6mm thick approved Corian, complete as per detail dwg. & Architect's instruction.

Modesty panel: Modesty shall be formed out of 19mm thick commercial ply boxing finished in 6mm thk approved Veneer Finish from outside and 1 mm tk laminate from inside. Provision for Cove lighting to be done as per dwg Complete as per detail dwg. & Architects instruction. Cost to include providing & fixing 6mm thk SS inlays as shown in the drawing.

Storage Unit : Providing and fixing Pedestal unit 2 nos of 620mm X 550mm X 650mm ht. made out of 19mm thk Commercial Ply finished with 1mm thk approved laminate . Drawer unit to have 2 drawers and 1 shutter made out of 19mm thk commercial ply finished with approved 1mm thk laminate , mounted on approved drawer channel, central locking, approved handle. Complete as per the detailed dwg and instructions of the Architect.

Transaction Counter : 20mm tk Transaction Counter to be made up of commercial finished with 12mm thk approved Corian as per the detailed desing & instuctions of the Architect.

Consider Basic cost of 6mm Corian @ Rs. 7000/sqm Consider Basic cost of 12mm Corian @ Rs. 13450/sqm

5.15 SECURITY TABLE - LAMINATE FINISH nos 1Dimensions : 2000mm X 750 mm X 900mm ht.

Table top: Table top of 650 mm wide to be formed out of of 19mm thick commercial ply clad with laminate on the top and edges and with approved laminate below the table top , complete as per detail dwg. & Architect's instruction.

Modesty panel: Modesty Panel 900mm high shall be formed out of 19mm thick commercial ply boxing finished in 1mm thk approved Laminate finish from outside & from inside .as shown in the drawing.Provision for Cove lighting to be done as per dwg Complete as per detail dwg To have 50mm high recessed Al Skirting per dwg Complete as per detail dwg. & Architects instruction.

Storage Unit : Providing and fixing Mobile Pedestal unit1no of Size 620mm X 550mm X 650mm ht. made out of 19mm thk Commercial Ply finished with 1mm thk approved laminate . Drawer unit to have 4 nos drawers made out of 19mm thk commercial ply finished with approved 1mm thk laminate , mounted on approved drawer channel, central locking, approved handle. Complete as per the detailed dwg and instructions of the Architect.

Consider Basic cost of Laminate @ Rs. 290/sqm

5.16 CONVENTION HALL TABLE - LAMINATE FINISH Rmt 41Dimensions : 600mm deep X 900mm ht.Table top: Table top of 600 mm wide to be formed out of of 19mm thick commercial ply clad with laminate on the top and edges and with approved laminate below the table top , complete as per detail dwg. & Architect's instruction.

Modesty panel: Modesty Panel 900mm high shall be formed out of 19mm thick commercial ply boxing finished in 1mm thk approved Laminate finish from outside & from inside .as shown in the drawing.Provision for Cove lighting to be done as per dwg Complete as per detail dwg To have 50mm high recessed Al Skirting per dwg Complete as per detail dwg. & Architects instruction.

Consider Basic cost of Laminate @ Rs. 290/sqm Mode of measurement Running length

5.17 BOARD ROOM TABLE - V SHAPED - 12 seater Nos 1.00

Dimension: 3610mm x 1800mm x 750mm

Providing and Fabricating Board room Table in 40mm tk block board finished in approved white Leatherite laminate

Table top: The table top to be formed out of 19mm thick commercial ply cladd using white leatherite laminate. The edge of the table to be provided with same laminate finish The top to house cable trough for cable management with 19mm thk ply openable as per details, complete as per detail dwg.

Base: The base of the table shall consist of 19mm tk commercial ply boxing finshed in laminate with 4mm groove with foam backingwith 50mm SS skirting as shown in the dwg, complete as per detail dwg.

5.18 SMALL RECEPTION TABLE - LAMINATE FINISHED

Dimensions: - 1500 mm X 600 mm X 1050mm ht. Nos 1.00 Dimensions: - 1300 mm X 600 mm X 1050mm ht. Nos 1.00

Counter top: Counter top to be formed of 50mm x50mm 2mm thk M.S frame work welded together to be cladded with19mm thick commercial ply to make boxing of 75mm thk finished with 1 mm thk approved laminate from all sides Modesty panel: Modesty Panel 900mm high shall be formed out of 19mm thick commercial ply boxing finished in 1mm thk approved Laminate finish from outside & from inside .as shown in the drawing.Provision for Cove lighting to be done as per dwg Complete as per detail dwg To have 50mm high recessed Al Skirting per dwg Complete as per detail dwg. & Architects instruction.




5.19 SMALL RECEPTION TABLE - VENEER FINISHEDDimensions: - 1500 mm X 600 mm X 1050mm ht. Nos 1.00 Counter top: Counter top to be formed of 50mm x50mm 2mm thk M.S frame work welded together to be cladded with19mm thick commercial ply to make boxing of 75mm thk finished with4 mm tk Veneer Finish from all sides

Base : The counter top to be supported 50mm dia by SS legs

5.20 RUNNING COUNTER rm 50.00

Providing & fabricating counter top made up of 25mm thick commercial ply finished with 1mm thk approved Laminate , 600mm deep. All the exposed edges to finished with approved edge binding , the table top shall be supported by 50mm dia M.S supports powder coated. complete as per Architect's instruction.

5.21 WARDROBE - VENEER FINISH Sqm 86.00 Providing & fabricating Wardrobe units for each Bedroom , formed out of 19mm thick commercial ply finished in 4mm thick approved Veneer Melamine polished consisting of two shutters, & 1mm thick approved laminate inside. The shutter of the Wardrobe shall be formed out of 19mm thick commercial ply finished in 4mm thick approved veneer melamine polished on the external side. with 1mm thick approved laminate on the inside mounted over spring loaded auto closing hinges of approved make, tower bolt. The exposed edges of the wardrobe shall be lipped using approved timber beading formed to shape melamine polished, also to include S.S. hanger rod, etc., complete as per detail dwg. & Architects instruction.




5.22 COT & MATRESS Nos 13Cot -Provide and fix Cot of size 2000x 1500 x 450mm comprising of approved timber with stainless steel vertical supports, 12mm thick ply base for the bed including necessary framing, head board with 100mm x100mm Engraved Teak wwod frame inside with 19mm ply finished with approved fabric around the headboard, The base shall be formed out of 50mm square Brushed finish SS support,complete in all respect as shown on drawings to meet Architect's approval. Rate shall include for the 6" thick foamed matress of approved make with bed spread and pillows,complete as per the dwg and the instructions of the Architects.

Side table -Providing & fabricating 2 NOS OF side table of size 400 X 400X400 MM formed out of 19mm thick commercial ply finished in 1mm thick approved laminate with edge lipping. The base shall be formed out of 50mm square Brushed finish SS support, complete as per detail dwg. & Architect's Instruction

5.23 T V LEDGE Nos 17Providing and fabricating Desk in Living rooms made up of 19mm commercial ply finished with 1mm thkapproved laminate , complete in all respect as shown on drawing to meet Architect's approval

SIZE: 1600MMX450MMX300MM

5.24 RUNNING COUNTER TABLE - Veneer finished Rmt 31Providing & fabricating counter top made up of 25mm thick commercial ply finished with 4mm thk approved Veneer , 550mm deep. All the exposed edges to finished with approved edge binding , the table top shall be supported by 50mm dia M.S supports powder coated. complete as per Architect's instruction.

5.25 DINING TABLEProviding and Fabricating Dining Table in 19 mm Perlaminated MDF.

Table top: The table top to be formed out of 19mm thick Prelaminated MDF, complete as per the Dwg or instructions of the Architects.

Base: The base of the table shall consist of SS legs fabricated using, 25mm square SS pipe sections framed together by welding tie bracers below the table top, complete as per the dwg & the instructions of the Architects.

Size:2800 x 900mm x900mm mm Nos 4

Size:2500 x 1000mm x900mm mm Nos 1


6.00 WALL FINISHESNote:Contractor shall protect the entire furniture provided by him or other agencies before starting the painting / punning work and shall be held responsible for any stains or damage including aluminum windows, AC grilles,

6.01 POP WALL PUNNING sqm 40.00 Providing and applying Plaster of Paris punning of average thickness 12mm to existing wall surfaces in true level and plumb complete as directed.

6.02 ACRYLIC EMULSION PAINT TY 1 sqm 10,900.00 Providing and applying acrylic emulsion paint finish to walls, blocked partitions, and plasterboard ceiling surfaces of approved shade, texture.

Existing wall surfaces to be prepare by scraping away any loose particles, dust, etc by washing and scrubbing and 1 coat of primer approved by manufacturer applied. The wall surfaces are then smoothened using putty approved by the manufacturers. Surfaces are then sandpapered to achieve a smooth finish and two or more coats of paint are applied as per manufacturer's specification.

6.03 TEXTURE PAINTING sqm R/oProviding and applying of approved shade as per drawings / directions & manufacturer specification.

Consider basic rate of texture paint at Rs. 970/- per Sqmt.

6.04 SPRAY PAINTING Sqm 0

Providing and spray painting of enamel paint on the service ducts of approved shade as per drawings / directions & manufacturer specification.


7.00 MISCELLANEOUS WORKS7.01 PELMET FOR BLINDS Rmt. 400.00

Providing and fixing Pelmet for blinds, made out of 19mm thick MDF, exposed edges of the pelmet shall be finished in approved enamel paint. The pelmet shall be in reversed "L" shape and shall be 150mm x 150mm in ht. The rate quoted shall be including fixing the pelmet with GI support @ 1200mm c/c anchor bolted to the structural ceiling etc., complete as per detail drawings.




7.02 PELMET FOR PULL DOWN SCREEN Rmt. 45.00

Providing and fixing Pelmet for pull down screen in meeting rooms, made out of 19mm waterproof ply for top and 12mm for sides. The pelmet shall be in reversed "U" shape and shall be 200mm x 250mm in size. The rate quoted shall be including fixing the pelmet with GI support @ 1200mm c/c anchor bolted to the structural ceiling, making the the pelmet ready to receive acrylic emulsion paint etc., complete as per drawings.

7.03 SOFT BOARD PANEL sqm 80.00 Providing and fixing Soft Board Panel over existing partition / wall with 12mm marine ply backing and 12mm thick. soft board (Cellotex- VOC FREE) with Gripper System.edges of the soft board to be finished with0 .5mm laminate to get better finish of corners as directed by the Architect. Consider Basic Price of fabric Rs. 250/Rmt excluding tax, delivery onsite and wastage.

7.04 KEY CHEST Sqm 3.00 Providing & fabricating storages formed out of 19mm thick commercial ply finished in 1mm thick approved

laminate. The top shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate,exposed edge of the table shall be lipped using approved Edge Binding. The shutter of the storage shall beformed out of 19mm thick ply frame and 5mm thk Glass with wooden beading allround, finished in 1mm thickapproved laminate.

Providing & fabricating storages formed out of 19mm thick commercial ply finished in 1mm thick approvedlaminate. The top shall be formed out of 19mm thick commercial ply finished in 1mm thick approved laminate,exposed edge of the table shall be lipped using approved Edge Binding. The shutter of the storage shall beformed out of 19mm thick ply frame and 5mm thk Glass with wooden beading allround, finished in 1mm thickapproved laminate. Storage to be complete with hardware installed as directed to consist of the following. Shutter to have auto-closing spring loaded hinge of approved make installed strictly as per manufacturers guidelines. All necessarytools should be strictly used for correct installation of hinges. Each set of shutters to be provided with 1 Nos.chrome finished multi-purpose lock of approved make, 75mm medium sized stainless steel tower bolt, 1 Nos.heavy duty SS ball catch, complete as per the drawing / instructions of the Architect. Cost also to includeprovididng and fixing SS Hookes to hang key bunches complete as per the instructions of the Architect .


7.04 ACOUSTIC FABRIC PANEL sqm R/oProviding and fixing fabric Panel over existing partition / wall with 12mm ply on which Acoustic Soft board ( Techno Acoustic panels ) is fixed & covered with approved Fabric with required Gripper System (Cellotex) required for the design elements as directed by the Architect. Consider Cost also to include providing and fixing 200mm wide Band finished with SS Brush Finish Laminate.

Consider Basic Cost of Acoustic panel @ Rs 1720/ sqm And basic cost of fabric @ 300/Rmt

7.05 GLASS WRITING BOARD PANELING sqm - Providing & fixing 8mm thick coloured Lacqured glass mounted over existing 12mm thick commercial ply backing projected 150mm from wall/partition face with Manet fittings of approved make. complete as per the detail drawing and instruction of the Architect.

Consider Basic Cost of Laqured Glass @ Rs. 4100 / sqm

7.06 FROSTING FILM sqm 127.00 Providing & fixing printed frosting film of 3M make of crystal range with approved image printed on the film as per design & installed over the glass partition as per manufacturer's specification & installation guidelines. Vendor shall include wastage while quoting. Vendor shall provide 10 year warranty as per manufacturer's guidelines.

Consider the Basic cost of film at Rs. 900 / sqmMode of measurement : Installed film shall be measured in length & height for payment.

7.07 PEN HOLDER 300mm x 150mm nos 20.00 Providing & fabricating 150mm Pen Holder formed out of 2 thick SS Sheet formed to shape and fixed, complete as per detail dwg.

7.11 VINYL GRAPHICS sqm 100.00 Providing & fixing vinyl Clear printed graphic film fixed using film adhesive. Vendor shall include wastage while quoting. Vendor shall provide 3 year warranty as per manufacturer's guidelines. Basic Rate- 1900/Sq.mt

7.12 WINDOW CILL sqm R/oProviding & fabricating 300mm wide x 1030 height ledge formed out of 19mm thick MDF formed to shape finished in approved laminate , complete as per detail dwg.




7.13 PLANTER BOX - LAMINATEDsize : 1200mmwide x 450mm deep x 450mm ht Nos 4.00 Planter box shall be fabricated using 19 mm waterproof ply . The boxing shall be cladded with laminate on all inner sides & External surface approved colour . The top to be lipped with 25mm x 12 mm approved timber beading creating a groove of 8mm in-between. The top of the boxing to be cladded with 19mm ply and to have cutout of 300mm dia at regular intervals as per enclosed drawing etc complete as per Architect's instruction. The boxing to be supported by 40mm x40mm MS box sections powder coated to grey ht 600mm as per the detailed dwg.

7.14 MDF BOXING sqm 20.00

Providing and fixing ply boxing using 19mm MDF of thikness from 150mm to 400mm on salwood frame work of section 50mmx50mm, etc..complete as per the drawigns and instrucions of the Architects.

7.15 ROLLER SHUTTERS Sqm 30Supply and fixing Rolling shutters made of Zinc Aluminum powder coated shutter of approved make, the shutter will be of Perforated type interlocked together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with hand operated lever operation complete including the cost of providing and fixing necessary wire springs and M.S. top cover including providing and Finishing with powder coated to approved shade for all sections prepared and applied as per manufacturer's specifications including preparation of surface, etc. complete all as per detail drawing. Detailed Proposal, calculations & Shop drawings for approval shall be submitted for Architects approval. This also includes plywood boxing finished in laminate of size 600 x 300mm as per the detailed drawings up to false ceiling.

7.16 PEBBLES kg 100.00

Providing & supplying of medium size white color pebbles as per the instructions of the Architect

7.17 BAMBOO SHOOTS nos

Providing and fixing Bamboo Shoots 25mm dia 7'-0" , as per the instructions of the Architects.

7.21 TRAP DOOR nos R/o

Providing and Fixing Trap Door of AMF Make 600 x 1200mm , complete as per the manufacturers instructions .

7.23 PLUMBING WORKS LS - Providng & Fixing Plumbing works for Pantry , including provididng supplying GI Pipes 25mm, PVC Pipes 75mm , with all necessary fixtures complete to connect from the point to the point provided by the builder. ( 2 nos of pantry per floor )

7.24 RAMP sqm - Providing and fixing Ramp in 19mm thick. Commercial ply, finished in anti-static laminate of approved shade as directed over a hardwood framework of 50mm x 50mm at the corners or as directed by the Architect .

7.25 STEPS sqm - Providing and fixing steps with 300mm tread & 150mm riser in 19mm thick. Commercial ply, finished in anti-static laminate of approved shade as directed over a hardwood framework of 50mm x 50mm at the corners or as directed by the Architect

7.26 MS RAILING -Café rm 12.00 Providing and fixing MS staircase railing 1050mm high with Verticals 100 mm flats spaced at 1000 mm regular intervals The horizontal members consists of 100mm Flats (2 nos ) and 10mm dia MS bars ( 4 nos ) welded to vertical as per the detailed dwg , Horizontal Supports are spaced at 148mm. All members to be powder coated, At the Top of the railing to have one no of 50mm dia MS pipe powder coated as shown in the drawing. ., complete including cost of materials, labour, Handling of machineries and electrical charges, etc., complete as per specifications.

7.27 RAILING FOR THE STAIRCASE Rm 8050mm dia Ms powder coated Single Railing fixed to the wall as shown in the drawing. ., complete including cost of materials, labour, Handling of machineries and electrical charges, etc., complete as per specifications.

7.28 CORNER GUARDS Providing and fixing Anodised Aluminium 25mm x25mm corner guards to the column edges Rmt 800

7.27 3M FLOOR MATTS

Providing and Supplying 3M floor matts /surface

Main Entrance - 3M Terra duty/Surface - Size - 4000mm x 900mm nos R/o

7.28 PLANTS nos 48.00 Providing & supplying of Plants with pots as per the instructions of the ArchitectConsider the Basic Price of Plant as 200/No




7.29 CEMENT POTSSupply of Cement Pots as per Manufacturers specifications as directed by the Architect.

CONICAL - 300mm dia 325mm ht nos 12.00 RECANGULAR - 900 x 350 x 450mm nos 8.00 CONICAL - 600mm dia 900mm ht nos 28.00 Basic Cost : Consider Basic cost of Rectangular at Rs. 6000 / no Excluding TransportationBasic Cost : Consider Basic cost of 300mmdia Conical at Rs. 3000/ no Excluding TransportationBasic Cost : Consider Basic cost of 600mmdia Conical at Rs. 7500 / no Excluding Transportation


8.00 CIVIL WORKS8.01 DEMOLITION OF 150mm / 200MM THICK SIZE-SOLID BLOCK MASONRY sqm

Demolition of 200mm thick SBM wall with the plastering, doors etc including carting away the same as directed by the Engineer-in-charge.

8.02 CONTRUCTION OF 150MM THICK SIZE-AEROCON BLOCK MASONRY sqm 11.00 Providing and constructing Aerocon block masonry of size 400x150x200mm and strength not less than 35 Kg/sqm in superstructure including cost of materials, labour charges, scaffolding, curing complete as per specifications.

8.03 CONSTRUCTION OF 100MM THK SIZE-SOLID BLOCK MASONRY sqm 84.00 Providing and constructing Solid block masonry of size 400x200x100mm and strength not less than 35 Kg/sqm in superstructure including cost of materials, labour charges, scaffolding, curing complete as per specifications.

8.04 PLASTERING sqm 190.00

Providing 15mm thick plastering in single coat with cement morter 1:3 to block masonry including rounding off corners whereever required, smooth rendering with lime, providing and removing scaffolding, including the cost of materials, labour, curing complete as per specifications.




8.05 WATER PROOFING sqm R/oProviding waterproofing for the Walls by surface method in two layers in cement mortar 1:4 of thickness 35mm for floor, 25mm for walls till floor level and 18mm till 300mm above / below floor level with waterproof admixture as per manufacturer's specification with a minimum guarantee of 10 years including the cost of hydro testing of the area etc complete.

Make : Fosroc , Sika India Pvt.Ltd

8.06 R.C.C LINTEL150mm x 200mm rm 8.50 Providing and laying Reinforced Cement Concrete of M25 grade at all levels, using river sand, 20 mm and down size coarse aggregates, including all leads and lifts, vibrating, scaffolding wherever necessary, curing and hacking as directed, including cost of required steel , necessary shuttering, centering and staging (approved by the engineer)

8.07 PCC SCREED CONCRETE sqm R/oProviding & laying plain cement concrete 1:3:6 for a mimumum thickness of 20 to 40mm over prepared bed with 12mm down size aggregates including the cost of all materials, labour, compaction, levelling, at all levels, leads and lifts, curing, shuttering etc complete as per instruction of Engineer-in charge

Mode of Measurementy : only plan area to be measured for payment]

- 8.08 HOUSE KEEPING LS 1.00

Providing house-keeping support with General House keeping for the entire site including clearing of wastes out of the premesis in regular basis inclusive of all dedicated labour and supervisory personnel at all times of work, across the entire facility. Cost to include all equipment, consumables, protective and safety measures, etc. complete. The site shall be kept clean to the complete satisfaction and based on instructions from the Project Managers.

-




SL No Particulars Unit QTY Rate Amount

1.00 GLASS PARTITION SYSTEM sqm 235.00Supply & Installation of Full Height Glass Partition System of 10mm toughened glass with proprietary Slimline partition systems of as per Manufacturers specification as verticals and horizontals at top and bottom with option for installing glass & glass to glass joint with other required accessories from FFL to 2700mm as per the drawing.and instructions of the Architects.

Mode of measurement : Length & height up to False ceiling shall be measured for payment.

2.00 SINGLE LEAF GLASS DOORSize : D7 - 900 x 2400mm Nos 14.00Size : D1 - 1100 x 2400mm Nos 19.00Supply & Fixing of Single Leaf Glass door. Door frame formed out of Standard Sections as per Manufacturers Specification.Complete as per details and instructions of the Architect.

Shutter : Providing & fixing glass door formed out of 10mm thick clear toughned glass. The glass shutter should be polished on the edges.

Hardwares to be usedDoor ClosureGEZE - TS 3000/Dorma - TS 92/Assabloy - YDC 3025Note - Door When opened should lock @ 90 deg.Door Hinges - Dorma / Geze / Assaabloy/Propreitory Mortise LockGEZE - Studio Rondo/Dorma - Studio Gala/Assabloy - GL - 02 Note:Tolerence of Door from Floor should be Maximum 4mmSaddle Plate to be Provided as per the Access Control RequirementSS floor Stop

3.00 DOUBLE LEAF GLASS DOORSize : D15: 1100 x 2400mm nos R/oSize : D 16 : 1500 x 2400mm nos 4.00Supply & Fixing of Double Leaf Glass door. Door frame formed out of Standard Sections as per Manufacturers Specification.Complete as per details and instructions of the Architect.

Shutter : Providing & fixing glass door formed out of 10mm thick clear toughned glass. The glass should be polished on the edges.

Hardwares to be usedDoor ClosureGEZE - TS 3000/Dorma - TS 92/Assabloy - YDC 3025Note - Door When opened should lock @ 90 deg.Door Hinges - Dorma / Geze / Assaabloy/Propreitory Door handle : 2 sets of 600 mm high and 22mm dia. Dorma/ Geze/ AssabloyCorner patch Lock ( Dorma/ GEZE/ Assabloy )

Note:Tolerence of Door from Floor should be Maximum 4mmSaddle Plate to be Provided as per the Access Control Requirement SS floor Stop

BILL OF QUANTITIES FOR GLASS PARTITION SYSTEM

PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai

DATE : 12.12.2013



SL No Particulars Unit QTY Rate Amount 4.00 SINGLE LEAF SINGLE SWING FLUSH DOOR

a) Opening size: D13 - 800mm X 2400mm nos 18.00

a) Opening size: D8 - 900mm X 2400mm (With Vision Panel 75 X 900mm) nos 11.00

b) Opening size: D12 - 1000mm X 2400mm (With Vision Panel 75 X 900mm) nos 1.00

Supply & Fixing of Single Leaf Flush door. Door frame formed out of Standard Sections as per Manufacturers Specification.Complete as per details and instructions of the Architect.

Shutter : Fabricating & fixing single leaf single swing flush door 42mm thk of apporved make, finished with 1mm thick laminate of approved make & colour on both sides. The shutter edges shall be lipped in 8mm thick approved timber beading melamine polished.

Hardwares to be usedConcealed Door ClosureGEZE - Boxer 224Dorma - TS 92Assabloy - Yale YIC5124HO Concealed Cam Action Power Adjustable Door closer, Size 2-4, Hold Open, Silver

Note - Door When opened should lock @ 90 deg.Door HingesGEZE - Ball Bearing Hinges 100mm x 100mm x 3mm

Dorma - Ball Bearing Hinges 100mm x 100mm x 3mm

Assabloy - Ball Bearing Hinge Y2BB-030 100mm x 100mm x 3mm

Mortise Lock with Half Cylinder with Lever HandleGEZE Dorma Assabloy / YaleAccessoriesAuto Matic Door BottomPerimeter Sill - GTS88 from Pemco to match the door colourNote:Tolerence of Door from Floor should be Maximum 4mm SS floor Stop



SL No Particulars Unit QTY Rate Amount 5.00 SINGLE LEAF SINGLE SWING FLUSH DOOR- VENEER

a) Opening size: D14: 1100mm X 2400mm (With Vision Panel 200 X 950) nos 13.00

Supply & Fixing of Single Leaf Flush door. Door frame formed out of Standard Sections as per Manufacturers Specification.Complete as per details and instructions of the Architect.

Shutter : Fabricating & fixing single leaf single swing flush door 42mm thk of approved make, finished with 4mm thick veneer of approved colour on both sides, melamine polished . The shutter edges shall be lipped in 8mm thick approved timber beading melamine polished.

Hardwares to be usedConcealed Door ClosureGEZE - Boxer 224Dorma - TS 92Assabloy - Yale YIC5124HO Concealed Cam Action Power Adjustable Door closer, Size 2-4, Hold Open, Silver

Note - Door When opened should lock @ 90 deg.Door HingesGEZE - Ball Bearing Hinges 100mm x 100mm x 3mmDorma - Ball Bearing Hinges 100mm x 100mm x 3mmAssabloy - Ball Bearing Hinge Y2BB-030 100mm x 100mm x 3mmMortise Lock with Half Cylinder with Lever HandleGEZE Dorma Assabloy / YaleAccessoriesAuto Matic Door BottomPerimeter Sill - GTS88 from Pemco to match the door colourNote:Tolerence of Door from Floor should be Maximum 4mm SS floor Stop

6.00 DOUBLE LEAF SINGLE SWING FLUSH DOORa) Opening size: D6 - 1500mm X 2400mm with Vision Panel nos 32.00a) Opening size: D9 - 1800mm X 2400mm with Vision Panel nos 10.00Supply & Fixing of Double Leaf Flush door. Door frame formed out of Standard Sections as per Manufacturers Specification.Complete as per details and instructions of the Architect.

Shutter : Fabricating & fixing double leaf single swing flush door 42mm thk finished with 1mm thick laminate of approved make & colour on both sides. The shutter edges shall be lipped in 8mm thick approved timber beading melamine polished.

Hardwares to be usedConcealed Door Closure : 2 seats of door closure GEZE - Boxer 224/ Dorma - TS 92/Assabloy :Yale YIC5124HO

Note - Door When opened should lock @ 90 deg.



SL No Particulars Unit QTY Rate Amount Door HingesGEZE - Ball Bearing Hinges 100mm x 100mm x 3mm

Dorma - Ball Bearing Hinges 100mm x 100mm x 3mm

Assabloy - Ball Bearing Hinge Y2BB-030 100mm x 100mm x 3mm

Door handle : 2 sets of 600 mm high and 22mm dia. Make : GEZE /DORMA / ASSABLOY

Dead lock : ( Dorma/ GEZE/ Assabloy )AccessoriesNote:Tolerence of Door from Floor should be Maximum 4mm SS floor Stop

GRAND TOTAL IN RUPEES EXCLUDING TAX -

Add Vat @ _____% on ______%


GRAND TOTAL IN RUPEES INCLUDING TAX -



PROJECT : National Centre for Sustainable Coastal Management Anna University , Chennai

OWNER : NCSCM

BILL OF QUANTITIES FOR MODULAR GRID CEILING

General Notes:Scope - Work shall include the furnishing of all materials, equipment and labour to install the complete ceiling system.

It is the contractors/suppliers responsibility to ensure that materials delivered to the installation site are safeguarded from the time of their purchase until they hand over the finished ceiling. It is desirable to store materials in a flat, clean, dry and secure space.

Controlled ventilation should be used to disperse moisture laden air.

Ceiling system shall be installed by a sub-contractor thoroughly experienced with this type of installation and approved by the manufacturer. The contractor to inspect premises prior to commencement of work and verify that the building is ready for installation.

Dust and loose particles should be removed by brushing or with a vacuum cleaner. Any pencil marks etc can be removed using ordinary pencil eraser. All damaged tiles to be replaced by the contractor.

Spot lights and other luminaires should not be supported by or on the ceiling tiles.

Suspension wire must always be mechanically pre-straightened prior to use and should not be less than 2mm dia.

The Modular Ceiling tiles which are removed for the installation of other service works shall be given back to the owner.

The Vendor has go through the co-ordinated service drawings to enable them to understand better the needs for additional engineered supports from the structural slab for supporting their Grid supports at no extra cost, wherever wide ducts and services run. Minor changes in the locations of services have been considered.



Sl.No. DESCRIPTION Unit Qty Rate (Rs.)

Amount (Rs.)

1.00 GRID CEILING 0.5/0.6 NRC sqm 315.00

Providing & installing Commercial type suspended modular ceiling consisting of

General requisitesGrids width: 15mm plain Tee grid finished in approved shade. The main Runners & cross Tees to have "stab" installation system made of corrosion-protected high tensile steel OR approved equivalent.

Tile specification :Tile type: Lay-in ceiling typeTile size: 600mm X 600mm X 15mm thk.Edge detail: Square EdgeLight reflectance: up to 0.90 ( 90% )Humidity resistance: 95% RHColor: White similar to RAL 9010Surface burning characters: Class1, BS 476:Part 7:1987Smoke Developed: 0 & Flame Spread = 5 as per ULThermal conductivity: 0.052 - .057 W/mkNRC: 0.5/0.6Thikness/Weight : 4.5 Kg/m2CAC: 34 dBSurface Pattern : Plain with random perforationsCeiling Suspension SystemProprietary supplied ceiling suspension system to consist of 2mm or 3mm GI suspension rod/wire with adjustable adjustable threaded "J" bolt of 3mm dia securely affixed to structural ceiling using soffit angle fixing bracket and 10mm dia hook type anchor fastener. Ceiling suspension system to be fixed at interval (grid) of 1200mm in both directions.

Proprietary supplied Grid System to consist of Main Runners @ 600mm and joined by Cross Tees @ 600mm to form overall grid opening of 600mm x 600mm. Additional cross tees are to be placed where appropriate for light fixtures, AC diffusers.

The grid system used shall be hot dipped galvanized steel sections, with exposed surfaces chemically cleaned and capped prefinished in high - gloss polyester enamel with two coat system on cold rolled steel.




Amount (Rs.)

Grid member sizesMain runners : 15mm X 40mm X 0.38mmCross tees : 15mm X 40mm X 0.38mmPerimeter section : 14mm X 20mm X 0.43mmFalse ceiling will be measured on horizontal plane only. Horizontal plane measurements are to be inclusive of all vertical drops, edge moldings, fascias, etc.

All extra tiles occupied by lights and diffusers to be returned to Owner.

Rate quoted to include all cut-outs required for light fixtures, smoke detectors and other services cut-outs complete as directed by Architect.

2.00 AXIOM TRIM Rm 340.00 Providing & installing Axiom Trim of 100mm height as per manufacturer's standards,specification & installation guidlines. Axiom trim consists of Classic Axiom 50mm trimchannel, Axiom T Bar connection clip, Axiom hanging clip, Axiom splice plate, etc., as perthe instruction of the Architect.


Add Vat @ _____% on ______%





1

2

3

4

5

6


Amount (Rs.)

1.00 CARPET TILE FLOORING TYPE : 1 sqm 955.00 Providing and laying of Carpet Tile over the specified area with following specification. The floor which recieves the carpet to be thourougly cleaned as per manufacturer's specification. The carpet is to be laid over a bed of manufacturer's approved adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing and clearing away of residual material to a location as directed. The rate shall also include supplying and laying of a protective layer of PVC or HDPE sheet of 50 microns thickness, held together with scotch tape. The laid carpet to be vacuumed after the removal of protective cover/on commissioning. If after the protective layer is removed and stains observed in the carpet because of in adequate protection, the same shall be shampooed and made good to the satisfaction of the project managers. The measurements of carpet will be the actual laid area.

.

Carpet floor shall be installed by a thoroughly experienced vendor and the type of installation shall be as per manufacturer's specifications. The Vendorshall inspect the premises prior to commencement of work and verify that the building is ready for installation.

PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai Date : 12-12-2013

Carpets to be laid as per the pattern indicated on drawing. All octroi ,frieght & handling to be accounted for and no additional amount shall be paidfor the same. Rate to be inclusive of covering of carpet with 125 micron single layer plastic cover & sealing of joints with tape. Any pencil marks etc.,shall be removed using ordinary pencil eraser. All damaged portions to be replaced free of cost.

It is the Vendor's / supplier's responsibility to check the area of the each type of flooring material before placing the order.

Areas like partitions thickness or columns that is not carpeted shll not be included in the payable costs.

BILL OF QUANTITIES FOR CARPET

General Note :Scope - Work shall include the furnishing of all materials, equipment and labour to install the complete Carpet system with the manufacturer's approved adhesive.

It is the Vendor's / supplier's responsibility to ensure that materials delivered on site is on the decided date by the project team & it is safeguarded fromthe time of his purchase until he hands over the finished flooring. It is desirable to store materials in a pred-decided flat, clean and dry surface.




Amount (Rs.)

Providing & laying carpet tile with following specification:Style: Tile carpetConstruction : Tufted Textured LoopFiber Product: 100% Solution Dye PPGauge: 39.4/10cm. (1/12)Finish Pile Thickness: 7.49mm +/- 0.5Production yarn weight: 20 ozDye Method: 100% solution DyedPrimary backing: Action BackTuft Bind: As per ASTM StandardsDelamination Strength: As per ASTM StandardsStatic Control: As per ASTM StandardsSoil retardant: ProtekAnti-Microbial:Alphasan Built in ProtectionMoisture Control: YesElectrostatic propensity: less than 3.5KV-Permanent Cond

Flammability( Radient Panel ASTM-E-662): >_0.45 ( Class I)


Add Vat @ _____% on ______%






Date : 12-12-2013

FS1 Work Table With Sink 1650 X 600 X (850+150) MM Ht 4

FS2 Work Top Deep Freezer 1200 X 600 X 850 MM Ht 1

FS3 4 Door Vertical Refrigerator 1

FS4 Work Table with u/s 1200 X 600 X 850 MM Ht 2

FS5 Fruit Storge Rack 1200 X 600 X 1800MM Ht 2

BOQ FOR KITCHEN EQUIPMENTS.

Sl. No. Item Description Image (Not exactly - Sizes Differ) Overall Size (in mm) Total Qty Unit Price Amount




PC Plate Pick-Up Counter with OHS 1500 X 600 X 1800MM Ht 2

S1 Plate Pick-Up Counter with Spoon Sterilizer & Tray Slide & Acrylic Canopy

1200x (650+300) x (850+600) mm Ht. 1

S26 Cont. Bain Marie Counter with Tray Slide & Acrylic Canopy 2100x (650+300) x (850+600) mm Ht. 1

S3Service Counter with 2 Cont & Tray Slide & Acrylic Canopy 450x (650+300) x (850+600) mm Ht. 1

DW1 Soiled Dish Landing Table with Chute 1500 X 600 X 850 MM Ht 1

DW2 3 Sink Dish Washing Unit 1800 X 700 X (850+150) MM Ht 1

DW3 Dish Un-Loading Table 600mm x550mm X (850+150) MM Ht 1




DW4 Clean Plates Landing & Wiping Table with U/S 1500 X 700 X (850+150) MM Ht R/o

DW5 Plate Storage Rack 1050 x 500 x 1800mm Ht. 1

T B R TWO BURNER COOKING RANGE 1200 x 600 x 850mm Ht. 2

IS IDLI STEAMER [4-COMPARTMENT]- STEAM 1

DS DOSA TOP GRIDDLE RANGE [with drain, C.I. Plate] 1

4 UNIT KOLGA STAND FOR DOSA BATTER 1

-

- GRAND TOTAL IN RUPEES INCLUDING TAX


Add Vat @ _____% on ______%




SL.NO ITEM SPECIFICATIONS IMAGE QTY (NOS) RATE AMOUNT REMARKS

1 RECEPTION LOUNGE

Providing and Fixing Barcelona Design Sofa With High Density Foam for Seat and Back , wrapped with approved colour Leather , with SS Legs as per the Image attached.

16.00

2 SINGLE SEATER SOFA - Cabins

Providing and Fixing Design Sofa With High Density Foam for Seat and Back , wrapped with approved colour Fabric , with SS Legs as per the Image attached.

52.00

3 TWO SEATER SOFA

Providing and Fixing Design Sofa With High Density Foam for Seat and Back , wrapped with approved colour Fabric , with SS Legs as per the Image attached.

8.00

4 SINGLE SEATER SOFA - Cabins

Providing and Fixing Design Sofa With High Density Foam for Seat and Back , wrapped with approved colour Leather , with SS Legs as per the Image attached.

6.00

5 CENTRE TABLE 1200mm x 600mm Providing and Fixing Centre Table Made of White laminated glass top with SS base finish complete as per the image attached

12.00

6 CENTRE TABLE 900mm x 600mm Providing and Fixing Centre Table Made of White laminated glass top with SS base finish complete as per the image attached

14.00


Date : 12-12-2013

LOOSE FURNITURE FOR NCSCM




7 SOFA

Providing and Fixing Design Sofa With High Density Foam for Seat and Back , wrapped with approved colour Leatherite , with SS Base as per the Image attached.

8.00

8 CENTRE TABLE CIRCULAR TABLE -750mm dia

Providing and Fixing Corian Table top , with SS Base as per the Image attached.

4.00

9 CAFETERIA CHAIRSProviding and Fixing Chair made up of High Density Moulded PVC Base , with Square Wooden Legs as per the image attached

74.00

10 CAFETERIA TABLES- 4 Seater Providing and Fixng Dinig Table of Size 900mm x 900 mm Isotop with SS Rectangular Base Brush Finish.

17.00




11 CAFETERIA TABLES - 6 Seater Provididng and Fixng Dinig Table of Size 1600mm x 900 mm Isotop with SS Rectangula Base Brush Finish.

1.00

12 POUFS - TYPE 1

Providing and Fixing Pouffs With High Density Foam for Seat , 450mm ht wrapped with approved colour Leather , with SS Legs as per the Image attached.

40.00

13 POUFS - TYPE 2

Providing and Fixing Pouffs With High Density Foam for Seat , wrapped with approved colour Leather , with SS Legs as per the Image attached.

20.00

14 POUFS - TYPE 3Providing and Fixing Pouffs With High Density Foam for Seat , wrapped with approved colour Leather , as per the Image attached.

5.00

15 Chairs

Provididng and Fixing Wooden Chairs with approved Timber finished with approved colour Polish as per the image attached. The cost also to include providing and fixing seat with high density foam wrapped with approved Leather ., complete as per the image attached.

34.00

0

0

Add ED @ ________%

Add Vat @ ________%

TOTAL AMOUNT WITH TAXES

TOTAL AMOUNT WITHOUT TAXES



1.00 WORKSTATION 261.00 Nos

Dimension: 1500mm X 1300mm X 1200mm ht. - Providing and installation of Modular workstation of 1200mm ht .

All metal surface to be MS Powder Coating finish

All complete as per the attached drawing.

Consider Basic Rate of Fabric @ Rs.500/rmt

Providing & Fixing CPU Holder underneath the table of Size 180 x 420 x 370mm made of MS powder caoted Sheet with Side perforation Panel for Ventilation . Complete with all necessary hardwares.as shown in the dwg and instructions of the Architect.

REFERENCE IMAGE

Table tops 600mm deep to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge. Top to have have Flip top to access the Electrical & Network Sockets, as per the dwg.

The panel in front of table top shall be of 8mm thk Laminated Glass as per detail dwg. The panel to have MS Powder coated bottom frame as per manufacturers specs . The side panel shall be Detachable / slidable Panel made of 12mm thk Magnetic soft board wrapped with approved Fabric with MS Powder coated frame as per manufacturers specs. Refer Drawing for Details.

The ends of the table top to be supported by Storage made of size 1350 mm x 450mm x 450mm Made of 19mm thk Prelaminated Partical Board as per manufacturers specs. This will include understructure support made of MS Powder coated tubular section of the workstation. The Top of the Storage to be provided with 50mm thk foam wrapped with approved Fabric as shown in the dwg.

All trims shall be of approved profile MS Powder Coated finish150 mm x 450mm Cable tray and Cable riser box made up of MS sheet powder coated to be provided below the table top as shown in dwg with seperation for data and power. The cable tray will house electrical sockets and data ports and will be accesable to user with Rotatable flip top with approved colour opening to 180 deg. as indicated in the drawing

PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai DATE : 12.12.2013

BILL OF QUANTITIES FOR WORKSTATION & MODULAR FURNITURES

Sl.No. DESCRIPTION QTY UNIT RATE AMOUNT



REFERENCE IMAGE Sl.No. DESCRIPTION QTY UNIT RATE AMOUNT

2.00 CUBICLE 58.00 NosDimensions: 1200mm X 750mm X 750mm ht.

3.00 SECRETARY TABLE 2.00 nosDimensions: 1250mm X 750mm X 750mm ht.

4.00 CABIN TABLE 11.00 nosDimensions: 1800mm X 750mm X 750mm ht.

Back Storage unit: The table to consist of storage unit of size 1800 mm X 450 mm X 750mm consisting filing cabinet finished with approved 1 mm laminate inside and outside with necessary approved hardware complete as per detail dwg.

Base: The base of the table shall consist of MS Powder coated legs as per manufacturers spec and matching with the legs provided for the workstation, with levellers complete as per detailed dwg.

Side Storage unit: The table to consist of storage unit of size 1500 mm X 450 mm X 750mm consisting filing cabinet finished with approved 1 mm laminate inside and outside with necessary approved hardware complete as per detail dwg.

Back Storage unit: The table to consist of storage unit of size 2100 mm X 450 mm X 750mm consisting filing cabinet finished with approved 1 mm laminate inside and outside with necessary approved hardware complete as per detail dwg.

Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.Cost also to include provididng and fixing 75mm dia Grommets 1no for each Table



Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.Cost also to include providing and fixing 75mm dia Grommets 1no for each Table

Base: The base of the table shall consist of MS Powder coated legs with panel below the table top as per manufacturers spec and Powder coating match with the legs provided for the workstation, with levellers complete as per detailed dwg.

Side Storage unit: The table to consist of side storage unit of size 3200 mm X 450 mmX 1200mm consisting filing cabinet with approved 1 mm laminate inside and outside with necessary approved hardware complete as per detail dwg.

Front Storage unit: The table to consist of Front storage unit of size 1370mm x 450mm x 1200mm consisting filing cabinet with approved 1 mm laminate inside and outside with necessary approved hardware complete as per detail dwg.

Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.Cost also to include providing and fixing 75mm dia Grommets 1no for each Table




5.00 TRAVEL DESK 1.00 nosDimensions: 1800mm X 750mm X 750mm ht.

6.00 GREEN ROOM TABLE /SECURITY TABLE/ RECORD ROOM 6.00 nosDimensions: 1200mm X 600mm X 750mm ht.

7.00 LINEAR TABLE - LIBRARY 8.00 nos

Dimensions: 1800mm X 1200mm X 750mm ht.

8.00 LINEAR TABLE- (DIGITAL IMAGE PROCESSING AREA) 16.00 nos

Dimensions: 1750mm X 800mm X 750mm ht.


Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical sockets and data ports and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.




Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical sockets and data ports and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.





Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge




9.00 CIRCULAR DISCUSSION TABLEDimension: 7500mm dia 3.00 Nos

. Dimension: 900mm dia 3.00 Nos

Dimension: 1500mm dia 3.00 Nos

10.00 DEPUTY DIRECTOR CABIN TABLE 1.00 nosDimensions: 2400mm X 900mm X 750mm ht.

11.00 DIRECTOR CABIN TABLE 1.00 nosDimensions: 2400mm X 900mm X 750mm ht.

12.00 CONFERENCE TABLE - 14 SEATER 5.00 Nos

Dimension: 4500mm x1200m

13.00 CONFERENCE TABLE - 12 SEATER 2.00 NosDimension: 3750mm x1000m

Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.Base: The base of the table shall consist of MS Powder Coated legs as permanufacturers spec and matching with the legs provided for the workstation with levellers complete as per detailed dwg.

Wire Management : Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical sockets and data ports and will be accesable to user with a flap . MS powder coated vertical raceways to be provided for electrical and networking.

Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.

Base: The base of the table shall consist of MS Powder Coated legs as permanufacturers spec and matching with the legs provided for the workstation with levellers complete as per detailed dwg.


Table top: 25mm tk table tops to be finished in approved Veneer. The table top to have a Post Formed Edge.

Base: The base of the table shall consist of SS legs as permanufacturers spec with levellers complete as per detailed dwg.

Side Storage unit: The table to consist of storage unit of size 1500mm X 450 mmX 750mm consisting filing cabinet finished with 1 mm laminate inside and with 4mm Veneer from outside with necessary hardware as approved complete as per detail dwg.

Table top: 25mm tk table tops to be finished in approved Veneer. The table top to have a Post Formed Edge.

Base: The base of the table shall consist of SS legs as permanufacturers spec with levellers complete as per detailed dwg.

Back Storage unit: The table to consist of storage unit of size 2400mm X 450 mmX 750mm consisting filing cabinet finished with 1 mm laminate inside and with 4mm Veneer from outside with necessary hardware as approved complete as per detail dwg.

Table top: Table tops to be made of 25mm thk approved Prelaminated Partical Board. The table top to have a Post Formed Edge.Base: The base of the table shall consist of MS Powder Coated legs as permanufacturers spec and matching with the legs provided for the workstation with levellers complete as per detailed dwg.

Cable tray in MS powdercoated finish to be provided below the table top as shown in dwg The cable tray will house electrical sockets and data ports and will be accesable to user with a flap .

Cost also to include provididng and Fixing 50mm dia Spine as per Manufacturers specs.




14.00 CONFERENCE TABLE - 10 SEATER 1.00 Nos

Dimension: 3100mm x1450m

15.00 WORKSHOP TABLE 1 Nos

Dimension: C SHAPED (3975mm x3750mm x 3975 mm ) x 100mm deep

16.00 TRAINNING ROOM TABLE 30.00 nosDIMENSION : 1300mmx 600mm x 750mm ht

17.00 PEDESTAL 314 nos

DIMENSION : 450mmx 450mm x 670mm ht MDF pedestal

-

Add ED @ ______%

Add Vat @ ________%

-

All junctions of column and workstation clusters shall be as per drawings issued by the Architects office. Where ever required partition shall be turned in order to facilitate networking / electrical cables to be drawn. This component must be taken into consideration while quoting for the workstation.

TOTAL WITH TAXES

Note:

Sizes may change as per site conditions & Architect ’s / Project Manager’s instruction.The vendor to submit BOM with component cost along with this quote.The vendor to submit the image & drawing of the workstation along with this quote.Laminate / fabric / Powder coated Metal surface colour as per samples approved by the Architect / Owner / Project manager.

Providing & Fixing Training room Table with following specification


Base: The base of the table shall consist of MS Powder Coated legs as per manufacturers spec and matching with the legs provided for the workstation with levellers complete as per detailed dwg.

Wire Management : 150 mm x 450mm MS powder coated Cable tray and Cable riser box to be provided below the table top as shown in dwg with seperation for data and power. The cable tray will house electrical sockets and data ports and will be accesable to user with Rotatable flip top with approved colour opening to 180 deg. One table to be shared by two.

Providing & placing in position Pedestal unit of 450mm X 450mm X 675mm ht. Pedestals are made from 19mm thk prelaminated Partical Board with matching colour Edge binding. Drawer unit shall consist of 2nos 19mm thk prelaminated Partical Board with approved colour edge binding of 300mm & 350mm ht. over foolscap filing drawers have full extension ball bearing slides. The drawers shall be provided with 19mm thick prelaminated Partical Board fascia with matching colour edge binding. Mobile pedestals to have an anti-tilt caster and all pedestals shall have a Individual locking system. All pedestals and flipper bins have quality locks with removable inner cylinders and are master keyed up to 2000 different combinations.

TOTAL WITHOUT TAXES









Sl.No. Description Unit Qty Rate Amount

1 Supplying & placing in position medium back chair with following specification. Nos 728.00

2 Supplying & placing in position medium back chair with following specification. Nos 111.00

Castors: Twin wheel high resistant polyamide castors.

Seat rest: Two Pieces of PP Plastic injection seat shells connected by 4 nos of self tapping screws. 50 mm range of adjustment of slideable seat. Common mounting opening ready with M6 nut for all different type of mechanisims, arms and backbones. Seatrest with polyurithene cout heavy duty foam and upholstered with approved Fabric.

Back rest: The medium back rest in fabric over frame. The back rest to have provision of height adjustable backrest for an optimum adjustment of the lumbar support, to be either by turning knob or push- button. upholstered with mesh - white colour/ approved colour

Mechanism: Synchronised moment of back and seat A 2 to 1 ratio and pivot point under the front rdge of seat. Pivotal pressure point of backrest provides full support in upright and any reclining posture . Tilt lock in multiple position and has reclining angle of 160 the reclining tension of backrest Gas lift: 100mm strocke imported pneumatic gas lift with 130mm range height adjustment and thrust force 400 newton.

Arm rest: P.P Plastic injection arm height adjustable ( 60mm range of adjustment) and arm support angle ( 180 Degree) swivelable possibility

Base: Chrome finished legs with nylon castors

Back rest: The medium back rest in fabric over frame. The back rest to have provision of height adjustable backrest for an optimum adjustment of the lumbar support, to be either by turning knob or push- button. upholstered with mesh

Mechanism: Synchronised moment of back and seat A 2 to 1 ratio and pivot point under the front rdge of seat. Pivotal pressure point of backrest provides full support in upright and any reclining posture . Tilt lock in multiple position and has reclining angle of 160 the reclining tension of backrest Gas lift: 100mm strocke imported pneumatic gas lift with 130mm range height adjustment and thrust force 400 newton.Arm rest: P.P Plastic injection arm height adjustable ( 60mm range of adjustment) and arm support angle ( 180 Degree) swivelable possibility

Base: MS powder coated base with high tonnage compression available in natural polished finish

Castors: Twin wheel high resistant polyamide castors.


Date : 12-12-2013 BILL OF QUANTITIES FOR CHAIRS

REFERENCE

Seat rest: Two Pieces of PP Plastic injection seat shells connected by 4 nos of self tapping screws. 50 mm range of adjustment of slideable seat. Common mounting opening ready with M6 nut for all different type of mechanisims, arms and backbones. Seatrest with polyurithene cout heavy



Sl.No. Description Unit Qty Rate Amount REFERENCE 3 Supplying & placing in position High back chair with following specification.

Nos 10.00

4 AUDITORIUM CHAIRS Nos 285.00

.

Supply and installation of ready made Auditorium chair foldable with steel frame,foam padding on seat and back,duly upholstered with rexin cloth by Godrej or Featherlite or equivalent, as per drawing specification and instruction of designer.

-

Add ED @ ______%

Add Vat @ _______%

GRAND TOTAL -

Arm rest: P.P Plastic injection arm height adjustable ( 60mm range of adjustment) and arm support angle ( 180 Degree) swivelable possibilityBase: Chrome finished legs with nylon castors Castors: Twin wheel high resistant polyamide castors.

TOTAL WITHOUT TAXES

Seat rest: Two Pieces of PP Plastic injection seat shells connected by 4 nos of self tapping screws. 50 mm range of adjustment of slideable seat. Common mounting opening ready with M6 nut for all different type of mechanisims, arms and backbones. Seatrest with polyurithene cout foam and Back rest: The High back rest in fabric over frame. The back rest to have provision of height adjustable backrest for an optimum adjustment of the lumbar support, to be either by turning knob or push- button. upholstered with Mesh

Mechanism: Synchronised moment of back and seat A 2 to 1 ratio and pivot point under the front rdge of seat. Pivotal pressure point of backrest provides full support in upright and any reclining posture . Tilt lock in multiple position and has reclining angle of 160 the reclining tension of backrest Gas lift: 100mm strocke imported pneumatic gas lift with 130mm range height adjustment and thrust force 400 newton.Head rest: Headrest to have height adjustable to support the neck upright or reclined with polyurithene cout foam and upholstered with mesh



SL.NO DESCRIPTION UNIT QTY RATE Rs. AMOUNT Rs.

1 ROLLER BLINDS - with Spring Booster System sqm 1830.00

Bottom rail: shall be round aluminium tube, anodized, with a diameter of 20mm & thickness of .5mm

Operation: Manual rollerRoller tube: Shall be extruded aluminium. The outside diameter of the tube shall be 25mm or 34mm depending upon the application.

Chain Drive Unit: Shall be of a high engineering grade moulded plastic with steel support pin enclosed in a plastic housing, and inserted into a control tube end. It shall be driven a ball chain pulley attached to a specially designed clutch mechanism, forming a continuous loop. It can be positioned on the left or right hand side of the shade. The shade when lowering or raising shall be automatically locked in position upon release of the ball chain by the clutch with its built in friction lock.

Chain Drive Idler end: Shall be of moulded plastic with a steel location pin enclosed in a plastic housing. The plug shall be inserted into the tube end.

Chain Drive installation Brackets: The installation brackets shall be Zinc plated steel supplied in pairs. One bracket in each pairs is used for the control side of the shade (side with the ball chain). The other bracket is used for the rotator or idler end side.

Ball Chain: Shall be 2mm Diameter PVC cord with 3mm diameter acetal balls moulded co-axially to it on 7.5mm pitch to form a continuous loop. It is used for raising or lowering the shade.

PROJECT : National Centre for Sustainable Coastal Management , (NCSCM ) , Anna University , Chennai Date : 12-12-2013

BILL OF QUANTITIES FOR BLINDS

Providing & fixing in position Roller Blinds of approved shade with following technical specification.Mechanism details:



SL.NO DESCRIPTION UNIT QTY RATE Rs. AMOUNT Rs.

-

Add Vat @ _____% on _____%

Add Service Tax @ _____% on ______%

GRAND TOTAL -

TOTAL WITHOUT TAXES

Weave : Basket weave 2/2Thickness of fabric : 0.55mm +/-5%

Consider the Basic Cost @ Rs . 900 / sqmApproved Make : Mac , Louverline , Grorich, Rosselle

Fabric width : 250 cm Rubbing fastness : DryFire rating : NFPA 701 Moisture Resistance : YesOpenness factor : 3%Fabric Descreption : SCREEN VISION 8%

Fabric specification:Fabric description : Combine visual comfort and thermal performance - Screen fabric for internal roller blinds - Two sides, two functions to combine visual comfort and thermal performance.

Fabric Weight ( g/m2 ) : 475 g/m2 +/- 10%

Composition : 84.5% PVC , 15.5% PolyesterLight Fastness : 7/8



SL.NO. DESCRIPTION UNIT Total Qty TYPE OF SIGNAGE SIZE RATE AMOUNT REFERENCE IMAGE

I SIGNAGES

Providing & fixing in position Signages with the following specifications.

1 Company Name Signage as per design- Reception set 1.00 Mounted 900 x 600mm Providing and fixing signage 1nos of size 900mm x 600mm letters with Logo- SS Brush Steel Logo

2 ALPHABETS ON LIBRARY STORAGE Nos 16.00 Mounted 75mm x 75mm Providing and fixing Alphabet signage of size150mm tk x 150mm x 25mm tk letters MS finish powder coated

3 Office Area Signages Nos 235.00 Mounted 300 x 75mmProviding and fixeing signage with 2mm thk SS brush finished plate withBlack vinyl sticker names fixed on the door with Birla 3M double sidedsticker as per the approved sample.

4 Rest Room ( Gents , Ladies & Handicap) Nos 60.00 Mounted 130x 150mmProviding and fixeing signage with 3mm thk ACP Sheet SS brush finishedplate with SS Symbol fixed with Birla 3M double sided sticker as per theapproved sample.

5 Push & Pull Signage on Glass Door Nos 75.00 Mounted 100 x 50mm

3mm thk brushed finished logo with viny sticker fixed with screws. as perapproved sample.


Date : 12-12-2013

BILL OF QUANTITIES FOR SIGNAGE WORKS



SL.NO. DESCRIPTION UNIT Total Qty TYPE OF SIGNAGE SIZE RATE AMOUNT REFERENCE IMAGE

6 Rest room way indicator Nos 22.00 suspended from the false ceiling

150mmX 300mm

Providing signage of 3mm thk SS brush finish ACP/Sunboard with vinylsticker on both sides as per design . Signage to be suspended from falseceiling using SS chain, as per image attached.

7 Emergency Exit Nos 65.00 suspended from the false ceiling

150mmX 300mm

Provididng & Fixing Emergency Exit signage , Power lit as per the Image

TOTAL WITHOUT TAXES -

Add Vat @ ______ % on ______%

Add Service Tax @ _______% on _______%

TOTAL WITH TAXES -

Note : The Exact Signages of Each type to be cross cheked at site beforeproduction.


Project: Interior fitout for NCSCM Client : NCSCM

58

1.0 FLOORING 1.1 CERAMIC TILE / VITRIFIED TILE FLOORING / DADOING / SKIRTING

The ceramic tile shall be of approved quality, make, color, size and shape. On the approval of the sample by the PM, the order for the tiles shall be placed from one source and procurement done preferably from one batch/consignment to prevent any shape variation. Tiles to be sorted out at site before laying.

The floor surface over which the tiles are to be laid shall be properly cleaned and wetted. 3 to 6 mm Solid bed of BALCEM GOLDSTAR (POLYMER MODIFIED CEMENTITIOUS ADHESIVE) & in conjunction with BAL-ADMIX AD1 (POLYMER MODIFIED LIQUID) shall be applied over an area adequate to accommodate about 20 tiles at a time. Tiles shall be washed clean and pressed on to the grout and gently tapped in its proper position. The tiles shall be placed perfectly side by side so as to have fine joints truly vertical and horizontal and in level with adjoining tiles.

The joints shall be as specified in the drawing, if grooves are to be provided, it shall not exceed 1.5mm or as specified in the drawing, and shall be done using spacers of approved quality. The excess content slurry bulging/oozing out in joints shall be removed by wiping immediately. Joints between the tiles to be filled with BAL GROUT to match the color of tiles as per the manufacturers’ specifications.

Thereafter, the joints shall be raked out to the required depth and loose cement/mortal shall be revved and joints shall be cleaned. Joints between the tiles to be filled with BAL GROUT to match the color of tiles as per the manufacturers specifications. (color as approved by PM) to match the color of tiles.

In the case of dado the wall surface shall be cleaned and plastered with CM 1:4 to a thickness of not less than 10 mm to form a uniform backing surface and finished rough and allowed to harden.

The tiles, which have been soaked in water, shall be cleaned and cement paste of butter like consistency applied to the backside of tiles and the tiles shall be pressed on the wall face and gently tapped in its position. In this way tiles shall be placed one after another starting from the bottom line and lay upwards.

The joints shall be truly vertical and horizontal, where required spacers – glass strips or ceramic strips – are used to achieve spacing between tiles of width as specified in the drawing, and the tile surface shall be of infirm level in all directions without any depressions and dulling which shall be tested by a straight edge as directed by PMC.

Curing and pointing of tiles in Dado shall be carried out as specified for flooring and as directed by PMC.

1.4 PRE POLISHED/FLAMED GRANITE SLABS IN FLOORING.

The granite shall be of approved color & shall be out of sufficient lot to cover particular area to avoid lot/shade variation.


59

Granite slab shall be quarried stones, hard, sound, durable and free from weathering and decay and defects like cavities, cracks, holes injurious veins, patches of soft materials and such other defects adversely affecting its strength and its appearance. The hardness of the Granite slab shall be as per IS. The pre-polished/flamed granite shall be selected and approved by the PMC. The pre-polished/Flamed Granite sample approved shall be brought by the Contractor in adequate quality and from one single batch/source so as to ensure that the grains and shade of entire flooring laid is homogeneous and consistent. The size and shape of the granite slab shall be cut as per the Drawings/instructions of PMC, edges being true and square. The exposed edges of the slab are to be polished at site or in factory. Cutting of Granite slabs shall be done using machines as approved by the PMC. The rate should include protection coat of POP over polythene till handing over. The rates shall be inclusive of machine-polished edges and groove if ordered.

Mortar shall be composed of cement and sand, unless otherwise specified. All mortar shall be prepared in accordance with IS 2250. The proportions of mortar measured by volume shall be as specified.

A layer of mortar shall be spread on full width over a suitable length of the lower course. Each slab shall be properly bedded and set in position by gently taping with handle or trowel or wooden mallet. The inside faces shall be buttered with mortar before the next slab is laid and pressed against it. The joints may be either paper cut or with spacing width. In case spacing is provided between slabs, the mortar in the joints shall be raked out and pointed (type of joint as specified by PMC or drawings) with cement slurry mixed with coloring pigment (the color of the pigment and its proportion to be mixed with the cement as specified) to match the shade of the granite. The curing shall be for a minimum period of 7 days after laying and pointing.

1.5 GRANITE LAYING IN STAIRCASE TREADS, LANDING AND RISERS

The laying of granite in Staircase treads, landing and Risers shall be similar to laying of granite flooring as above, except that.

The slabs cut shall be from one single piece, joints shall be paper joint, the

edges shall be treated as shown in drawings. Anti skid grooves shall be provided for every Tread and Landing as per Detail

drawing. the treads and Landing shall be projecting a minimum of 20mm from the top face of the riser.

The cut is to be polished either in site or at factory. The edge of the treads shall be fully bull nosed / chamfered & polished to

gloss as per detail dwg. 1.6 GRANITE SKIRTING

The pre polished granite shall confirm to the specification or requirement as that of Granite used in flooring/staircase. The thickness of the Granite used shall be 20mm thick and it is fixed over a backing coat of cement mortar of 1:4 of 12mm thick with a cement paste backed on the back of the granite tile.


60

The height of the skirting shall be 100mm or as specified the top edge of the skirting shall be treated as shown in the drawing.

The joints of the granite strip used in skirting are to be less in numbers and it shall be paper cut joint. The paste oozing out is wiped in a cloth and washed with water. The curing is to be for a minimum period of 7 days.

1.7 SKIRTING SS skirting over ply: - fabricating and fixing 50 mm high SS skirting clad over 12mm

thick marine ply using epoxy adhesive.


61

2.1.0 CARPENTRY / JOINERY Scope of work includes Materials such as wood, labor for joinery of wooden frame and shutter, fixing of the frame and shutter, fixing of laminates or veneer, fittings and fixtures and such other related carpentry works.

2.1.1 MATERIALS.

Wood for Furniture shall be approved, seasoned and I class Steam Beachwood. It shall be fairly uniform in color and texture. It shall be free from blemishes, hollow pockets and knots, spinals or twisted grain, warp and any kind of decay or insect attack, cupcakes, door holes, splits, cracks, pinholes, wormholes etc.

Wood shall be kiln seasoned before being planed to the required sizes, in accordance with IS 401-1982.

Samples of seasoned wood and Commercial Boards/Plywood’s shall be submitted to PM for approval, before placing order. The contract shall get the wood and Commercial Board/Plywood sample tested in an approved laboratory. If desired by the PM, the Contractor shall submit all information such as manufactures/brand name, test certificate etc.,

The contractor shall submit test certificate in support of the kiln seasoning including ASCII treatment for the entire quantity of timber required for the work from the factory where seasoning has been done. Commercial Flush Shutters of thickness 19/32/33 mm & 45 mm and of size as specified in drawings shall be solid core type with block board core and shall conform to IS 2202 1983 – part I (specification for wooden flush door shutters solid core type) IS 1003 part 1 and 2, IS 3097. Flush door shutters shall be free from twist or warp in plane, and the four edges of the shutter shall be square. Both faces of shutter shall be sand papered to a smooth and even texture. Tolerance on nominal thickness shall be + 0.8 mm. Thickness of shutter shall be uniform throughout with the variation not exceeding + 0.8 mm when measured at any two points.

All commercial shutters shall be internally lipped using approved wood, pressed and ready from the Factory directly. In the case of double leafed shutters, rebating shall be as indicated in drawings and directed by the PMC. Where separate lipping is provided, the depth of lipping at the meeting of styles shall not be less than 35mm.

Shutters shall not be damaged during transportation, storage and fixing. Damaged shutters shall be rejected and shall be replaced with new shutter as directed by the PMC whose decisions will be final and binding in this regard. From the time the shutters are procured to the time they are taken up for fixing in position, the shutters shall be stored in a proper manner with adequate supports so as to avoid damages to any part, particularly the edges.

The Flush shutter shall be laminated with plastic laminate sheet or veneer, whose samples shall be submitted along with manufacturers’ brand name, test certificate etc to the PMC for approval before placing order. The laminate/veneer sheet is protected with building paper until ready for use.

2.1.2 MOISTURE CONTENT


62

The average moisture content of all the WOODEN samples from a lot shall be within + 4% and moisture content of individual samples + 6% of the maximum permissible moisture content. For this purpose the site of work shall be deemed to fall under climatic zone II. Seasoned wood as per IS 1141 –1973 and IS 287 – 1973 shall be basis of acceptance.

2.1.3 WORKMANSHIP

Timber sections for frames shall be planed smoothened to accuracy on all sides to the full dimension, rebated, rounded, chamfered or moulded as shown in drawings or as directed by PM without patching or plugging of any kind before they are framed and jointed. A tolerance of + 2 mm shall be allowed in the finished cross sectional dimensions. The joints shall be of mortise and tendon or tongue & groove type simple, neat and strong. Joints shall fit in fully and accurately without wedging or filling. The joints shall be glued, framed, put together and pinned with hardwood or pins not less than 10 mm dia, sash bars if any shall have metered joint with styles. Putty where used shall conform to IS 419-1967 and shall be a homogeneous paste and shall be free of dust, grit and other visible impurities.

After the frames are put together, they shall be pressed in position by means of a press. The contact surfaces of tendon and mortise joints shall be treated (before putting together) with bulk type synthetic resin adhesive of a make approved by the PM. Rails, which are more than 180 mm in width, shall have 2 tenens. Styles and shutters shall be made out of a single piece and shall have a 12 mm groove to receive panels.

Before the frames are fixed in position, these shall be inspected and passed by the PM. The frame shall be placed in proper position, secured to walls or columns as the case may be, with bimetallic fasteners, iron hold fasts etc. as shown in drawings and directed by the PM. In case of doorframes with sills are provided, these sills shall be embedded/sunk in the floor for full thickness of the floor. The doorframes without sills, while being placed in position, shall be suitably strutted and wedged in order to prevent warping during construction. The frame shall be protected for damage during construction.

Where glazed openings are indicated, the size, thickness and type of glazing shall be provided as in the drawings and shall be lipped internally with S. Beech wood. Shutters shall have provision for mortise locks where so indicated on drawings or as directed by the PM.

Shutters shall be checked after fixing for proper location, alignment and swinging. After fixing all the fittings the shutters shall be tried again for proper closure, handling and easy movement etc., and any defects noticed should be immediately rectified as directed.

2.1.4 PRE LAMINATION / VENEERING TREATMENT

Before Lamination/Veneering the Commercial Flush board with Laminate/ Veneer sheet, the surface to be laminated/veneered should be thoroughly cleaned, all cracks and nails holes filled as directed. The laminate sheet shall be fixed using approved quality adhesive recommended by the manufacturer and applied strictly in accordance to their instruction/specifications. The adhesive shall be applied in a thin layer and while still tacky, it shall be spread evenly with steel in both directions to


63

assume full contact with the adhesive / Fevicol / SR. A constant and even pressure is applied for not less than 24 hours to ensure good bonding of the sheet to the board. The laminate/veneer surface shall be cleaned as recommended by the manufacturer of all stains/ adhesive marks etc.

2.1.5 SURFACE TREATMENT

All Wooden and Veneered surface shall be water cut melamine finished after it has been approved and passed by the PM. All portions of timber built into masonry or abutting a concrete portion of the building or buried in ground shall be coated with boiling coal tar or other type of approved wood preservative or primer before fixing them in position.

2.1.6 FITTINGS AND FIXTURES

All fittings and fixtures for the doors, storage and worktops shall be as indicated in the schedule shown in the drawings. The samples along with manufacturer’s / brand name, test certificate etc, shall be submitted to the PM for approval before placing order.

2.1.7 LOUVERS FIXED TO FRAMES.

The louvers shall be of wood, glass or any other materials as specified in the drawings. These shall be fixed in grooves made in the frame or shutter. The Venetian blades shall slope down towards the outside at an angle of 45° or as shown in drawings. These shall overlap each other by about half of their widths. Beading shall be fixed all around the openings for louvers as indicated in the drawings.

2.2 PARTITIONS 2.2.1 GI CORE PARTITION

50 X 25 GI sections can be used for framework having vertical members at 600mm c/c fixed with horizontal noggins at floor and soffit and the centers, wherever required in line and level, 12.5mm tapered edge. Gypboard (Conforming to IS –2095-1982) is then screw fixed to either side of timber frame with 25mm long drywall screws at 300mm c/c with joints staggered to avoid through joints. Finally the face layer of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with jointing compound, paper tape and two coats of primer suitable for Gypboard (as per recommended practices of India gypsum or equivalent.)

2.2.2 FULLHEIGHT GYPBOARD PARTITION: Full Height Partitions to be fabricated using 25 x 50mm GI section framework @ 600 c/c bothways with horizontal noggings at floor and soffit, on both side skinning with 12.5mm Tapered edge gyp board (IS-2095/1982), in line and level screw fixed to either side of GI section with 25mm long dry wall screws 300mm c/c with joints staggered to avoid through joints finished so to have flush look with jointing compound paper tape and two coats of primer suitable for Gyp board as per recommended practices. complete and Glass wool insulation of 50mm thk inside the partition filled with Kimco/Rockwool insulation as per dwg. All electrical/network


64

switch boxes, niches to be boxed/packed with adequate reinforcement using plywood. 12mm GI channel to be provided at intersection of two materials.

2.2.3 FULL HEIGHT- DOUBLE GYPSUM PARTITION: Full Height Double Gypsum Partitions of 136mm thk to be fabricated using 25 x 50mm GI section framework @ 600 c/c bothways with horizontal noggings at floor and soffit, on both side skinning with 12.5mm Tapered edge gyp board (IS-2095/1982), in line and level screw fixed to either side of GI section with 25mm long dry wall screws 300mm c/c with joints staggered to avoid through joints finished so to have flush look with jointing compound paper tape and two coats of primer suitable for Gyp board as per recommended practices. complete and Glass wool insulation of 50mm thk inside the partition filled with Kimco/Rockwool insulation as dwg. All electrical/network switch boxes, niches to be boxed/packed with adequate reinforcement using plywood and also 12 mm GI channel to be provided at intersection of two materials.

2.2.4 FULL HEIGHT HALF- GLAZED PARTITION:

Same as in full height partition but partly glazed partition with (10mm thk toughened clear glass) above 2100 mm from floor till 3000mm ht. & with Gypsum partition below as per Gypsum partition specifications etc., Complete as directed with in fill of Kimco or Rockwool insulation and also 12 mm GI channel to be provided at intersection of two materials.

2.2.5 PARTLY HEIGHT DOUBLE GLAZED PARTITION Same as in full height double gypsum partition but partly Double glazed partition of 136mm thk. with (10mm thk toughened clear glass) above 2100 mm from floor till 3000mm ht. & with Gypsum partition below as per Gypsum partition specifications etc., Complete as directed with in fill of Kimco or Rockwool insulation and also 12 mm GI channel to be provided at intersection of two materials.

2.2.6 FULL HEIGHT GLAZED PARTITION Full Height Double Glazed Partitions to be provided with 10mm thk toughened glass using 25mm x 25mm x 2mm thk SS C channel on top and bottom, including cutting groove in the floor to fit C channel and the gap is filled with GE silicon gel and top with MS frame work to fix the C channel and painting the MS framework with enamel paint, compete as per dwg., and directions

2.2.7 FULL HEIGHT LAMINATED GLAZED PARTITION Providing and fixing Full Height laminated glass partition in combination of 5mm thk etched glass, 5mm thk clear glass and 2mm thk raisen laminate fixed using glass fins on top and with 25mm x 25mm SS C-Channel in the floor and filling the gap with GE silicon sealant at the bottom, Complete as per dwg., and directed.

2.2.8 PARTITION ABOVE FALSE CEILING: Partition above false ceiling with GI frame of 25mm x50 mm at 600mm x 600mm c/c. Frame to be fixed to ceiling. All internal frame members to be screw fixed. Internal voids to be glass wool in filled for sound proofing. No finishing required. Provide required cutout for Return Air passage.

2.2.9 MEDIUM HEIGHT PARTITION:

Medium height partition, 75 mm thick with GI frame of 25mm x50 mm sections at 600mm x 600mm c/c, faced both sides with 12mm thk Gypboard with 10mm x 10mm grooves (made using AL “L” angles) at all ends. Frames to be fixed to the floor. Inside


65

voids to be filled with 50 mm thk panels of glass wool/ rock wool. All gypsum board edges to be protected with aluminum angles. Partition to include Approved skirting at floor level. All internal frame members to be screw fixed.

2.3 STORAGE: 2.3.1 FULL HEIGHT STORAGE: LAMINTED:

Full height storage with top, bottom to be made out of 19-mm pre laminated board / ply with Approved veneer / laminate lipping. Back to be provided of 8-mm thick pre laminated board. The sides of the storage to be made of 19 mm thk pre laminated. All shelves to be adjustable and made of 19 mm thk commercial ply. Openable shutters to be made out of 19-mm thk board with balanced shutter with 1 mm thk Approved laminate or 4mm thick approved veneer fixed on all sides. Shutters to be fixed complete with all necessary fittings like hinges,brass ball catch, SS cranked tower bolts, locks, handles of specified make and size as per details.

2.3.2 FULL HEIGHT STORAGE –VENEERED:

As per item No 9.1.1 but with 19 mm balanced shutter with 4mm thick Approved veneer melamine polished on the outside and all inside surfaces laminated in Approved laminate.

2.3.3 MEDIUM HEIGHT STORAGE:

M.H storage to be formed out 19mm pre laminated board, with Approved veneer lipping finished on all sides. Provide 19 mm pre laminated shelves as directed. The Top, sides and shutters of the storage to be made out of 19 mm thk veneered comm. Ply. All shelves to be adjustable or as directed by Architect. Openable Shutters to be hung with spring loaded hinges of specified make, inside surface to be finished with laminate and fixed complete with all necessary fittings like hinges, brass ball catch, tower bolts, locks, handles of specified make and size as per details. All the surfaces shall be laminated / veneered.

2.3.4 LOW HEIGHT STORAGE (Veneered):

Low height storage of 900 mm ht as per details and specifications of item no. 9.1.3 with approved veneer. Openable Shutters to be hung with spring loaded hinges of specified make, inside surface to be finished with laminate and fixed complete with all necessary fittings like hinges, ball catch, tower bolts, locks, handles of specified make and size as per details.

2.3.5 LOW HEIGHT STORAGE (Granite Top):

Low height storage as per details and specifications of item no 9.1.3 but with top in 19 mm thk granite of approved shade with machine cut and polished edges.

2.3.6 OVER HEAD STORAGE:

As per item 9.1.3 but hung onto wall and with bottom faced with laminate/veneer and detailed as per the drawing.


66

3.1.0 GLAZING

The following Indian Standards shall be followed

IS 1761 – 1960 Specifications for transparent sheet glass for glazing and framing purposes.

IS 2835 –1975 Specification for transparent sheet glass. IS 5437 –1969 Specification for wired and figured glass

IS 419 – 1967 Specifications for putty for use on window frames IS 3548 –1966 Code of practice for glazing in Buildings IS 1200 – 1970 (Part XIV)

The glass shall be transparent and free from blisters, stones, scratches and bubbles so as to give a clear visibility throughout the glass. The sheet glass should not show any distortion of light when tested according to the method prescribed in Appendix ‘B’ in IS 1761-1960. The cut size of sheet glass shall be within the following tolerance, on both length and width of the prescribed cut size.

Thickness Tolerance on cut size

Mm 2.5 and below + 1.5 3.0 and above + 2.0

The thickness of sheet glass when tested according to the method prescribed in Appendix –C in IS 1761 – 1960, shall be as follows, within the tolerance indicated against each.

The size for glazing shall allow a clearance of 2.5 mm between the edges of the glass and the wood or metal surrounds. The clearance may be increased, provided the depth of the reedit or groove is sufficient to provide not less than 15-mm cover to the glass. The detailed process of glazing shall be as specified in IS3548 –1966 code of practice for glazing in building.

All stains form the surface shall be removed and cleaned with thinner. The edge of glass or glazing sheet when rounded shall render a uniform look throughout the length and shall be neatly finished.


67

4.1.0 FABRICATION WORK/ STAINLESS STEEL WORKS 4.1.1 FABRICATION TOLERANCES

Unless otherwise shown on the drawing, the fabricating tolerances shall generally be as follows:

Straightness: compression members shall not deviate from straightness by more than 1/1000 of the axial length between points, which are to be laterally supported.

Completed members shall be free from twist bends and open joints. Sharp links or bends shall be cause for rejection of materiel.

Length: of 1 mm is permissible in the overall length of members with parts of the structure, shall have a variation for the detailed length not greater than 2 mm for members 10 meters or less in length and not greater than 3 mm for members over 10 meters in length.

4.1.2 STAINLESS STEEL WORKS

All stainless steel used should be conforming to BE 316 in brushed finish.

The stainless steel pipes shall be procured from approved manufacture and of approved grade. The quality of stainless steel sheet and pipe shall be approved by PM before proceeding with execution any item of work. The surface finish of the entire component used in executing the item should be brushed finished

4.1.3 HAND RAIL

The pipe used for handrail shall be of 14 gauges thick. All joints to be done with welding only of TIG (tungsten inert Gas). The welded links are to be ground and organ buffed to get the original finish of the surface of the material welded. The joints or junctions where two pieces are joined/welded to be precisely cut and then welded, SS Bal Acrylic emulsion s and 10mm thk toughened glass. The fixing details of the handrail shall be as specified in the drawing or instructed by PM / Architect.


68

5.1.0 PAINTING 5.1.1 CEMENT PRIMER

The surface shall be thoroughly cleaned of suet etc., and be allowed to dry for at least 48 hours. It shall than be rubbed thoroughly with sand paper to give a smooth and even surface. Any unevenness shall be made good by applying putty, made of plaster of Paris mixed with water on the entire surface including filling up the undulation and then sand paper the same after it is dry.

The cement primer shall preferably be applied by brushing and not by spraying. Horizontal strokes shall be given first, and vertical strokes shall be applied immediately afterwards. The entire operation shall constitute one coat. The surface shall be financed as smooth as possible leaving no brush marks.

5.1.2 ACRYLIC EMULSION PAINTS.

Acrylic emulsion paint of approved brand and manufacture shall be used. The primer where used as on new work shall be oil-based primer. These shall be of the same manufacture as the plastic emulsion or as approved by PM. Only sufficient quantity of paint required for days work shall be prepared.

The paint and primer shall be brought be brought by the Contractor in sealed tins in sufficient quantities and from one single batch/consignment, and the same shall be kept in the joint custody of the Contractor and the PM. The empty tins shall not be removed from the site of work till this item of work has been completed and passed by the PM.

Preparation of the Surface: the scaffolding used for painting should be erected taking care not to rest on the walls so as to avoid any damage to the wall surface. For new work the surface shall be thoroughly cleaned of dust, old white or color washes by washing and scrubbing. The surface shall then be allowed to dry for at least 48 hours. It shall then be sand papered to give a smooth and even surface. Any unevenness shall be made good by applying putty, (made of ingredients plaster of Paris, chalk powder, primer, paint etc., mixed as specified or directed by the PM) on the entire surface including filling up the undulation and then sand papering the same after it is dry.

One coat of sealer and two coats of Acrylic emulsion paint are to be applied. The application is done using good quality approved make brush. On the final application, roller is used to get a better and acceptable finish (the roller application is done on smooth wall surface only). At places where required, the application of paints is done on granular finished surface, in which case no application of putty and sand papering is required. The work is to be carried out under direct Guinness and instructions from the manufacturers whose expert advice and supervision are to be made available in order to achieve the high-grade finish. The painters employed for this work must be capable of producing the highest standard of workmanship required. If the finish is of doubtful nature, the contractor shall have to rectify the entire, at his own cost, to the satisfaction of the PM.

5.1.3 TEXTURED PAINTING


69

All textured paint to confirm to specific IS. The paints of specific make/manufacture that are mentioned in the specifications are to be used. The textured paints may be of exterior / interior grades as specified.

The surface is prepared free of dust/dirt/grease and other foreign matters. The scaffolding is to be done as for the other type of painting.

Texture finish painting is a wall coating available in different readily available textures finishes and colors and is a substitute to conventional wall finishes. These paints can be texture recessed raised, granular smooth etc. dinettes. The glossy can be achieved by adding marble powder to the required proportion.

As far as possible only ready mixed color/shades is used directly unless until a shade difference is required, which is achieved using strainers of approved make and color, mixed in approved proportion.

The thickness of granule used in the textured paint is 2.5mm. This finish can be applied on any surface of finish like cement plaster, good surface of brick masonry and also already painted surface. The textured finish acts as better fire retardant coat against the conventional type of painting. This paint is also anti-fungus and anti-corrosive.

The finish needs a minimum of 3 hours to dry and shall be ready to use after 24 hours.

The application is either done with brush or spray gun or trowel (also manual pressure on the trowel) or roller depending on the required finish and as per the manufacturers’ instruction. The applicator should be skilled and specially trained by the manufacturer of the particular texture paint to do such work.

Basically the application process is

Application of base coat either one or two depending on the required finish of the selected texture. The color of the base coat is to be approved by the PM / Architect.

Application of ready mixed paint is by any of the already mentioned type i.e. by brush spay trowel, roller etc. depending on the type of finished required.

5.1.4 PAINTING STEEL SURFACES

The contractor shall purchase synthetic enamel paint of approved quality make color and shade.

All steel surfaces shall be thoroughly cleaned of all dirt, grease and rust. Any small areas, which become inaccessible after assembly, shall be painted before assembly. The surface shall be perfectly dry before painting. The priming coat for steelwork shall be applied after the surface has been prepared. After the priming coat has dried all blowholes and dents shall be filled with metal paste and surface smoothed with sandpaper.

Wherever shop primer painting is damaged, the surface shall be thoroughly cleaned and touched up with corresponding primer.

Site painting shall not be done in frosty or foggy weather or when humidity is such as to cause condensation on the surface to be painted.


70

The contractor shall take care to clean thoroughly all stains of paint on glasses, walls, fittings, fixtures etc. by applying turpentine on thinner.

5.1.5 POWDER COATING.

The powder coating to be done on steel / aluminum surface shall be epoxy hi bird or pure polyester. The Finish shall be Matt, glossy /semi-glossy, textured or structure types which shall be as approved by the PM. The variation in thickness of coating shade of the color and finishes shall be achieved varying the temperature of heating.

The process of coating is basically.

Degreasing Watering Picking/chromatin Water rising Phosphating Oven heating and Cooling at room temperature etc.

The quality / color / shade of the powder used shall be of reputed approved manufacturer. The contractor shall submit to the PM a sample for approval before finally placing an order. The thickness of powder coating shall be based on the surface being coated and the resilience to weathering effects required for the particular item. The thickness of coating varies from a minimum 20 microns to maximum to 60 microns. The temperature of oven heating shall be around 185°C. The specialists/manufacturers’ specification in using the product shall strictly be adhered to in preference to the specification in the contract.

5.1.6 VAPOCURING

Vapocuring finish shall be done for Metal surfaces exposed to both interior and exterior atmosphere. The putty material, hardener, base coats material, Polyurethane coat material and the paints used shall strictly be in accordance with the manufacturers’ specification.

The quality/color/shade to be applied shall be as per drawings. The Contractor shall submit to the PM a sample for approval before finally placing an order. The quality of coating is based on the surface being coated, the resilience to weathering effects required for the particular item as approved by the PM. The Specialists/Manufacturers’ specification in using the product shall strictly be adhered to, in preference to the specification in the contract.

Heating shall be at 70°C. Temperature may be varied depending on the hardener added with the color in specified recommended proportion. The surface to be vapocured should be first made free from dust, dirt, grease or any such foreign material. The porches of Vapocuring shall be done under a dust free environment and basically consist of

Preparation of the surface Putty Work Spray coat either mixed with hardener or other wise Heat treatment


71

Polyurethane coating, etc. 5.1.7 MELAMINE FINISHING

Melamine finishing shall be done on wooden surfaces. The finish shall be Matt, glossy, semi glossy type which shall be as approved by the PM.

All uneven and rough surfaces shall be rubbed-using sandpaper of the required grades till a smooth surface is obtained and the surface shall then be well dusted. The nail marks/ pores in the wood shall be filled with wood filler and the surface shall be rubbed with the required grade of sandpaper so that the entire surface is uniformly smooth. After preparing the surface as specified above, application of a sealer coat shall be done. Wherever necessary the pores in the wood shall be again filled with wood filler and the surface shall be rubbed with the required grade of sandpaper in the presence of water so that the entire surface is uniformly smooth. Staining as required shall be done manually, application of second coat of sealers shall be done. Finally 3 coats of Melamine spraying, strictly under dust free condition, shall be done, after which the surface is buffed with Wax & Oil.

The Specialists/Manufacture’s specification/instruction in using the product shall strictly be adhered to, in preference to the specification in the contract. It is preferable to carry out the process under warm weather condition. The spray gun before/after using shall be cleared thoroughly using thinner or spirit.


72

6.0 FALSE CEILING 6.1.0 SUSPENDED FALSE CEILING: GYPSUM

False ceiling should be carried out with lightweight boards made of basic materials like aerated gypsum treated with special additives, and both sides are covered with a special off white/white color paper. The size, thickness and texture of the board or tile available is as per the manufacturer details.

The Gypsum boards or tiles should confirm to IS 2542-1981 and IS 2095-21982 physical properties of Gypsum board should confirm to: Density: nominal in a dry state = 807.10 kg/m Fire resistance: 12.5mm = ½ hour resistance. Material classified as class

1 surface soared of flame test as per BC476 PART –7 1971

Sound insulation: The average rate of noise reduction between frequencies of 100 Hz is 35.6 dB for a partition 75 mm or 97 mm thickness with a 12.5mm board on each face 38.5. DB for a partition as above but including 265 mm of mineral wool in the cavity 42.5 BD for a 100mm partition comprising of two layers of 12.5-mm board on each side.

Gypsum board is basically available with the properties as below. Thickness in mm

Width in mm Weight in kg/Mt

Thermal conductivity

Thermal resistance in m K.W

9.5 610& 1220 8.0 0.16 0.06 12.5 610.1220 10.5 0.16 0.08

Gypsum board should be flexible enough to resist any crack due to limited movement of a building.

False ceiling should present unbroken surface and desirable continuity may be varied by treatment of joints with wood or plastic or PVC or metal or any other such material strips.

Off loading of gypsum is only advisable on small boards and may be carried by one man but generally two men will be required and this will reduce the risk of damage to the boards. Boards are manually carried on edge.

When storing boards, care should be taken to keep in a dried and covered place sheltered from rain and avoid dampness from floors. They should be supported on wooden battens, which should not be more than 45 cm apart on a flat surface.

Deformed gypsum boards (because of poor handling or storage) are difficult to erect. It is suggested that the board is stacked in different piles according to size and thickness so that the work can be carried out more effectively in terms of time. Care should be taken not to stack the piles too high. Gyp board should never be stacked on edge for a long period as this can cause deformation.

Gypboard can easily be either longitudinally or transversally cut. A cut should be made in the face side of the board by means of a retable knife. A line may be ruled


73

prior to cutting or with practice. The rule may be drawn down the board at the required distance from the edge whilst the board is scored with a knife at the edge of the rule. The board should then be pressed with both hands and gypsum score will break in the line with the cut in the side face. The board should then be turned over and the side paper be cut with the knife.

Gypboard may be cut using a normal saw. A fret saw or an electric tool may also be used for the cutting of curves. When large quantities of board are to be cut, the use of a circular handsaw is advisable.

Electrical or manual carpenter’s tools as those employed in the cutting of wood may be used for making cutouts in gypsum board. A drill should be used when making holes for electrical installation thermostat boxes, etc. For holes of diameter less than 50mm high speed steel drill should be used.

The edge of the board can be pared off using planes. A file may also be used to level off any irregularities, which may remain after cutting. The edge of both papers, faces may be trimmed by using fine sand paper

Gypboard may also be used to line curved areas. The curvature radius shall be 60cm for 9.5mm board and 100cms for 12.5-mm board. 30 to 60 minutes before application to curved areas, both sides of the gyp board should be sprayed with water until they are damp. The board should then be bent very slowly and carefully, and fixed in to position. Before joining the boards should be completely dry

The ceiling is suspended using systems made of G.l. The suspended ceiling may be heavy duty (load bearing ceiling on which a person can walk over a ladder for maintenance purpose) or light duty (non loading bearing). Both these systems may be either with a layer of vinyl film laminated.

On completion of the erection of the grid work, care should be taken to see to it that the bottom face of the grid work is on true water level or to the required gradient or profile

Where light fittings, access panels and similar components are incorporated as a part of the design requirement, consideration must be given to maintaining the integrity of the ceiling. The fire and sound insulation are also important factors.

The joining treatment of two-gyp board is described below

TAPERED EDGE JOINT: A continuous thin band of jointing compound of gyp board joining compound is applied to the trough of the tapered edge point. The joint tape is then pressed in to the band of jointing compound, firmly embedded and free from tapered air bubbles with sufficient jointing materials under the tape to ensure good adhesion

Immediately after the tape has been fixed, a new layer of material is applied over it, flush with the surface of the board. Before the material begins to stiffen the jointing sponge should be moistened and surplus material wiped from the edge of the joint without disturbing the main joint filling. The sponge should be rinsed occasionally to


74

prevent material setting in it. Once the material is dried any slight depression in the surface can be filled again and projection cut back

When the material has dried about 1 hour after application, a thin layer of jointing compound is applied in a broad brand 200mm wide. The edges of this band should be immediately feathered with a slight damp joining sponge. When the joint material has completely dried another application is made 250mm wide and feathered out as before. It is important that the first coat of finish is allowed to dry before the final coat is applied

CUT EDGES: A finish similar to that achieved with the tapered edge

board can be obtained with cut edge boards or acute edges and tapered edge board. The cut edge should slightly sanded to remove any burrs The edge of the adjoining boards is cut to make v-groove with a sharp knife. The joints are flush with the face of the board, using gyp board jointing compound. The gap must be filled solidly back to the framework. The coat is applied and joint tape bedded in it as tightly as possible, leaving sufficient material behind the tape to ensure good adhesion and to eliminate air bubble. Gyp board jointing compound is then applied with a sponge. When this has dried a second application of 200mm wide is applied and the edges are feathered out. Wider feathered out of the joint will overcome slight misalignment of cut ends and edge joints.

NAIL AND SCREW SPOTTINGS:

This process fills any indentation left by the hammer or screw head when fixing the board. With the layer of jointing compound which is struck off level with the face of the board and allow drying. The operation is completed with one more similar application.

SURFACE TREATMENT:

When the jointing is dry, one coat of gyp board dry wall topcoat is applied to the entire surface using the medium pile roller, and brush or entirely by brush.

All the accessories like the ceiling section, perimeter channels, intermediate channels, clips, cleats jointing compound jointing tape screws nails etc used in erecting the false ceiling should be recommended by the manufacturer and under the instruction or guidance of the manufacturer

The type of board –size, texture, edge finish or the type tiles used should be strictly as per the approved selection of the PM / Architect.

6.2.0 GYPSUM BOARD WALL LINING


75

This lining is done either on to masonry insulation natural or any other material using specified thickness Gypsum board manufactured by approved agency. Specified GI section of appropriate gauge is screwed on to the surface to be lined with gypsum board and subsequently board is dry screwed on to the sections. The joining of boards, treating of joints and surface finishing is similar to that the false ceiling.


76

7.0 TECHNICAL SPECIFICATIONS FOR THE MODULAR FURNITURE 7.1 WORK STATIONS

1. Table top : Standard table top height – 750mm (including table top thickness of 25mm) 2. Work surface shall be 1500 mm long x 600 mm deep made up of 25mm thick laminated plain

particle board with post formed edges. 3. Table top to have powder coated Flip top to access the Electrical & Network Sockets. 4. The edges of work surface shall be provided with post formed edges. 5. Non‐working edges of the work surface shall be provided with machine pressed 0.5mm thick

PVC lipping / edge binding. 6. Cable tray and Cable riser box made up of MS sheet powder coated to be provided below

the table top with separation for data and power. The cable tray will house electrical sockets and data ports and will be accessible to user with Rotatable flip top with approved colour opening to 180 deg.

7. The panel in front of table top shall be of 8mm the Laminated Glass .The panel to have MS Powder coated bottom frame. The side panel shall be Detachable / sliding panel made of 12mm thick Magnetic soft board wrapped with approved fabric with MS Powder coated frame.

8. Storage: size 1350 mm x 450mm x 450mm made of 19mm thk prelaminated particle Board. This will include under structure support made of MS Powder coated tubular section of the workstation.

9. The Top of the Storage to be provided with 50mm thk foam wrapped with approved Fabric for seating purpose

10. CPU Holder : Fixed below the table top of size 180 x 420 x 370mm made of MS powder coated sheet with side perforation panel for ventilation complete with all necessary hardware.

7.2 CUBICLE


77

1. Table top : Standard table top height – 750mm (including table top thickness of 25mm) 2. Table top to be made of 25mm thk approved pre‐laminated particle board. The table top to

have a Post Formed Edge. 3. Table top to have 75mm dia Grommet 1no to access the Electrical & Network cables. 4. The edges of work surface shall be provided with post formed edges. 5. Non‐working edges of the work surface shall be provided with machine pressed 0.5mm thick

PVC lipping / edge binding. 6. Base : The base of the table shall consist of MS Powder coated legs with panel below the

table top which is powder coated matching to the legs 7. Storage: The cubicle to have a side storage and a front storage. 8. Side Storage of size: 3200 mm x 450 mm x 1200mm consisting filing cabinet. 9. Front storage of size: 1370mm x 450mm x 1200mm consisting filing cabinet. 10. The storages are made of 19mm tk prelaminated board which is finished by 1mm tk

laminate from inside and outside with necessary hardware . All the edges to be provided with machine pressed 0.5mm thick PVC lipping / edge binding.

7.3. CABIN TABLE

1. Table top : Standard table top height – 750mm (including table top thickness of 25mm) 2. Table tops to be made of 25mm thk approved pre‐laminated particle board. The table top to

have a Post Formed Edge. 3. The table top shall be factory‐made, pre laminated board with laminate of 1mm thickness 4. Table top to 75mm dia Grommets 1no to access the cables. 5. The edges of work surface shall be provided with post formed edges. 6. Non‐working edges of the work surface shall be provided with machine pressed 0.5mm thick

PVC lipping / edge binding. 7. Base : The base of the table shall consist of MS Powder coated legs with panel below the

table top which is powder coated matching to the legs 8. Storage: The cubicle to have side storage and a back storage. 9. Side Storage of size: 1000 mm X 450 mm X 750mm consisting filing cabinet. 10. Front storage of size: 1800 mm X 450 mm X 750mm consisting filing cabinet. 11. The storages are made of 19mm tk prelaminated board which is finished by 1mm tk

laminate from inside and outside with necessary hardware . All the edges to be provided with machine pressed 0.5mm thick PVC lipping / edge binding

7.4. CONFERENCE TABLES

1. Table top : Standard table top height – 750mm (including table top thickness of 25mm) 2. Table tops to be made of 25mm thk approved pre‐laminated particle board. The table top to

have a Post Formed Edge. 3. The top shall be factory‐made, laminated with laminate of 1mm thickness 4. Bottom shall have a backing laminate of minimum 0.6mm thickness. 5. Base: The base of the table shall consist of MS Powder Coated legs. 6. Cable management: Cable tray in MS powder coated finish to be provided below the table

top .The cable tray will house electrical sockets and data ports and will be accessible to user with a flap .The table also to have MS powder coated vertical for electrical and networking cable entry.

7.5. DIRECTOR TABLES


78

1. Table top : Standard table top height – 750mm (including table top thickness of 25mm) 2. Table tops to be made of 25mm thk approved particle board finished in Veneer polished in

melamine . The table top to have a Post Formed Edge. 3. Base: The base of the table shall consist of SS legs as per manufacturer’s specs.’ 4. Side storage : size 1500mm X 450 mm X 750mm consisting filing cabinet finished with 1 mm

laminate inside and with 4mm Veneer from outside with necessary hardware

7.6 PEDESTAL

1. Pedestal unit of size: 450mm X 450mm X 675mm ht. 2. Pedestals are made from 19mm thk prelaminated Particle Board with matching colour Edge

binding. 3. Drawer unit shall consist of 2nos 19mm thk prelaminated particle Board with approved

colour edge binding of 300mm & 350mm ht. over foolscap filing drawers have full extension ball bearing slides.

4. The drawers shall be provided with 19mm thick prelaminated particle board fascia with matching colour edge binding.

5. Mobile pedestals to have an anti‐tilt castor and all pedestals shall have an individual locking system.

6. All pedestals and flipper bins have quality locks with removable inner cylinders and are master keyed up to 2000 different combinations.


79

8.0. SPECIFICATION OF POWDER COATING (a) Powder coating shall be with Epoxy powder of a standard shade or as required. (b) The specific gravity of powder should be such that it gives DFT (Dry Film Thickness) of 50 – 60 micron. (c) It should withstand salt spray test of not less than 1000 hrs as per ASTM‐ B‐ 117. (d) SCRATCH HARDNESS TEST as per DIN 53153 shall be conducted and results should be such that no scratch shall show bare metal with a load of 3 kgs. (e) The following seven step phosphating process treatment shall be conducted before powder coating. (i) Hot water rinse (ii) Knock of Degreasing (iii) De‐rusting (iv) Cold water rinse (v) Activation (vi) Phosphating (vii) Passivation.

Documents

Download Technical Specifications & BOQ