DS2 USER MANUAL.pdf

XK3190-DS2

WEIGHING INDICATOR

MANUAL

PLEASE READ THIS MANUAL VERY CAREFULLY

BEFORE USE

FEB 2007

Specifications subject to change without prior notice

1

CONTENTS

1. GETTING STARTED

2. TECHNICAL PARAMETERS AND SPECIFICATIONS

3. LAYOUT OF INDICATOR

4. KEYBOARD AND METROLOGY OPERATION

5. MENU OPERATION

6. INPUT

7. CALIBRATION

8. COMMUNICATION

9. PRINT AND RECORD OPERATION

10. INTERFACE SET UP

11. INFORMATION INDICATION

12. MAINTENANCE AND WARNINGS

APPENDIX

1. GETTING STARTED

CAUTION

This is not a toy. Keep out of reach of children;

This indicator is not an explosion proof device;

This indicator is not a water proof device;

Do not open this indicator, no user serviceable parts inside.

Always contact supplier for service.

1.1 Introduction

Weighing indicator XK3190-DS2 adopts 32-bits fast speed and

high performance ARM processor and effectivemulti-tasks

embedded operating system. Hence its with convenient character

input and personal operating window. Its widely applied in

static weighing system equipped with 1~16 digital load cell.

1.2 Features

With 32--bits fast speed and high performance ARM

processor

With effectivemulti-tasks embedded operating system

With personal operating window

With planar rolling menu management

With plenty parameter setting clew

With error diagnose function

With Num/English character/Chinese character/sign

input method similar to mobile phone input

2

With shortcut recall for common information such as

vehicle NO. and cargo name

Able to connect with digital load cell(ect. HBM)

Auto/manual angle adjustment

Call and display inner code to replace weight observing

and analysis tolerance

Password management and timing power-off function

Able to setup print function for auto/manual; daily/sorted

statistics report printing

Able to setup print function for fast filled weighing bill

Weighing data save/check/delete/ protection in case of

power off

Standard RS232C /RS422/RS485 communication interface

with selectable baud rate

Standard scoreboard interface with 20mA current loop

method

Standard parallel print interface

Able to save 1000 vehicle ID and corresponding tare weight

1000 cargo ID and corresponding cargo name1000 weighing

records

2.TECHNICAL PARAMETERS AND SPECIFICATIONS

Model:XK3190-DS2

Digital load cell connection

-Connection method: RS422/RS485

-Connection distance: About 1000 meters

-Connection quantity:1~16

-Communication protocol of load cell: HBM, YAOHUA,or customized

-Load cell power: DC 12V,0.8A(Max)

Display

-Display method: VFD dot-matrix display(256*64)/LCD

dot-matrix display(240*60)

-Display range:000000~999999(without decimal point)

-Division:1/2/5/10/20/50

Keyboard

-Soft-touched rubber keyboard

-23 keys, 6 extended keys

Clock: real clock

Scoreboard interface

-Signal output method: serial

-Signal: 20mA current loop(constant current)

-Baud rate: 600

-Transfer distance: 2000 meters

Printer interface

-Method: With standard configuration of parallel printer

interface, able to connect with printer model LQ-300KKX-P1131

LQ-1600K

Serial communication interface

-Standard interface: RS232C/RS422/RS485

-Baud rate: 600/1200/2400/4800/9600, communication method

selectable

-Transfer distance: RS232C 30 meters; RS422/RS485 1200

meters

Power supply

-AC 110~220V;50~60HZ

3

-DC 24V

Operation temperature:0~40

Transportation temperature:-25~55

RH: 85RH

Housing

-Stainless steel housing, waterproof

-Size: 250mm*250mm*70mm (without bracket)

-Weight: 3.6KG

3. LAYOUT OF INDICATOR

3.1 Front view of the indicator

3.2 Back view of the indicator

3.3 Side view of the indicator

4

3.4 Window when powered on

Note: This window will appear when indicator is powered on or

when indicator gets no signal from load cell

3.5 Main window(weighing window)

Vehicle NO.: 10 character Cargo No.10 character Time

3.6 Main board description

A2006688 STELL 15:31:20

98765.43 kg

AUTO COMM INDER CODE STABLE NET ZERO

AC POWER

SUPPLY

LOAD CELL

CONNECTION

RS232/422/

485

PRINTER

INTERFACE

5

Note: After open back housing of the indicator, get power supply

cable, communication cable, printer cable through the

water-proof connector, and connect according to the hardware

configuration described in the following chapter.

4. Keyboard and metrology operation

4.1 Keyboard View

4.2 Key description

Key Description

[1/ABC Cargo No.] Setup for cargo no. at weighing mode;

123eric 1 or letter ABC at setup mode;

[2/DEF Vehicle No.] Setup for vehicle no. at weighing mode;

123eric 2 or letter DEF at setup mode;

[3/GHI SETUP] Enter into setup main menu at weighing

mode;

123eric 3 or letter GHI at setup mode;

[4/JKL SUP PRINT] Execute supply printing at weighing mode;

123eric 4 or letter JKL at setup mode;

[5/ MNO REP PRINT] Execute report printing at weighing mode;

123eric 5 or letter MNO at setup mode;

[6/PQR TARE PRESET] Setup for tare preset at weighing mode;

123eric 6 or letter PQR at setup mode;

[7/STU TOTAL PRINT] Execute total printing at weighing mode;

123eric 7 or letter STU at setup mode;

[8/ VWX SAVE PRINT] Execute save printing at weighing mode;

123eric 8 or letter VWX at setup mode;

[9/YZ CALIBRATE] Enter calibration setup at weighing mode;

123eric 9 or letter YZ at setup mode;

[0 BACKLIGHT] Open/Close backlight at non-setup mode;

123eric 0 at setup mode;

[TARE] Execute tare operation at weighing mode;

[ZERO] Execute zero operation at weighing mode;

[INPUT MODE] Switch between input mode at setup mode;

[CHECK] Enter into record checking window;

[INPUT] To input and save for parameter;

[WEIGH] To skip zero calibration while calibration

6

and directly to load calibration;

Directly to main window of weighing at

other setup mode;

[DELETE] Delete record or delete input value digit

by digit;

Enter into record delete menu at weighing

mode;

[ON/OFF] Power on or power off operation;

Press this key for 2~10 seconds to power off

indicator, or else it will execute reset

function;

[SAVE TARE] Enter into save tare window;

[] Direction key, menu or record page up;

[] Direction key, menu or record page down;

[] Direction key, back to former menu or enter

into menu bar at left;

Select left sign at PINYIN or SIGN input

mode;

[] Direction key, enter into next menu or

enter into menu bar at right;

Select right sign at PINYIN or SIGN input

mode;

[F1][F6] Extend function key, invalid currently;

4.3 Metrology operation

4.3.1 Power on and auto zero

A, After powered on, indicator display opening window and

initialize parameter, check communication setup. It enters into

weighing mode automatically. Indicator display error when load

cell connection is abnormal.

B, When power on, if weighs on platform deviates from zero point

but within auto zero range, indicator will perform auto zero.

4.3.2 Manually zero

A, Press [ZERO], indicator will be back to zero, and zero light

will be on;

B, Zero key will only be valid when weighs on platform is within

manual zero range;

C, Zero operation is valid only when stable light is on;

D, If indicator is at net weight mode, press [TARE PRESET] to

set it as 0, and back to weighing mode then zero operation is

valid;

4.3.3 Tare operation

There are three methods to tare:

-Method 1, Normal tare

Press [tare] key when weighing data is positive and stable,

the displayed weighing data will be regarded as tare weight,

then indicator will display 0 and net light is on;

7

-Method 2,Preset tare

Press [TARE PREST] key at weighing status, indicator enter into

tare preset window, the displayed data is the former tare. If

new tare is needed, then input by 123eric key and press [INPUT]

to confirm. Press [] to return back weighing mode;

-Method 3,Call tare weight according to vehicle no.

Press [VEHICLE NO.] at weighing status, indicator enter into

vehicle/tare setup window. After inputting the right vehicle

no., press [INPUT] to call the tare of this vehicle from the

memory. If no need to change the tare of this vehicle, then

press [TARE] to regard the tare as current tare and back to

weighing mode;

5. Menu Operation

5.1 Menu list

KEY MENU SUB-MENU

[Cargo No.] Cargo Name

[Vehicle No.] Vehicle No./ Tare

[SAVE PRINT] Input Vehicle No./

Cargo No.

[TARE PRESET] Preset Tare

[SAVE TARE] Vehicle No./ Tare

[REP PRINT] Daily Report Repot Date

General Report 1

General Report 2

General Report 3

General Report 4

General Report 5

General Report 6

[DELETE] Delete by Time Record Date

Delete by Vehicle

No.

Vehicle No.

Delete by Cargo No. Cargo Name

Delete All RCD

[CALIBRATE] Calibrate PWD

IDT Calibrate Division

Decimal Point

F.S.

Zero point

Load

Angel Adjust

Manual method Quantity of LOCEL

LOCEL Address

Coefficient Adjust

Auto method Quantity of LOCEL

Load Weight

LOCEL Calibrate No. of LOCEL

Note: Setup used by

LOCEL supplier

Zero Point of LOCEL

50% F.S. of LOCEL

F.S. of LOCEL

LOCEL Address LOCEL New Address

8

Change LOCEL ISN

LOCEL Type

Unit

Zero Track Range

Manual Zero Range

Auto Zero Range

Dgtl Filter Int.

Calibrate P of IDT Zero Point

Calibrate

Coefficient

[CHECK] Check by Date Record Date

Check by Vehicle

No.

Vehicle No.

Check by Cargo No. Cargo Name

Check VEHNO of RCD!

Check CARNO of RCD!

Check Ovrload

Record

[SETUP] Prnt Setup Function PWD

Prnt Method

Prnter Type

Prnt Back Zero Rst

Prnt Format

Min. Prnt Weight

Filled Prnt option

Company Name

Comm Setup Comm Method

Comm Address

Baud Rate

Date/Time Setup Calibrate PWD

Date/Time Setup

Date/Time Display

Display Contrast

Cargo No. Enable

Vehicle No. Enable

Calibrate PWD

Change

Timing PWD Change

LOCEL Check

LOCEL Searching

IDT ISN

5.2 Operation mode description

There are three operation modes for user to select which could

offer quick, intelligent and convenient way for operation.

5.2.1 Single key mode

Press one key to execute corresponding operation, keys that

works in this way are: [4/JKL SUP PRINT] [ZERO] [TARE] [0

BACKLIGHT][WEIGH]

Example: press [ZERO] at weighing mode, then indicator would

zero

5.2.2 Single Menu mode

9

For operation that needs value input, press one key, then direct

to value input, keys that works in this way are: [1/ABC Cargo

No.] [2/DEF Vehicle No.] [SAVE TARE] [6/PQR TARE PRESET] [8/

VWX SAVE PRINT]

Example: Press [1/ABC Cargo No.] at weighing mode, it directs

to Cargo Name WINDOW. Input area displays against white while

input mode is displayed at the right top corner. User could

press [INPUT MODE] to switch among different input modes, that

is 123/ABC/PINYIN/SIGN. Press [INPUT] to save while [] to main

window. Cargo Name WINDOW displays like following

5.2.3 Menu bar mode

For these not frequently used and complicated parameters, user

could find parameter according to type through menu bar. There

are five keys that direct to sub menu for more operation

according to function. Menu list is as described above. The

five keys are: [3/GHI SETUP] [CHECK] [5/ MNO REP PRINT] [9/YZ

CALIBRATE] [DELETE]

Example: Press [SETUP] at weighing mode, then operate like

mobile phone style to select the right menu item you want to

setup parameter, then press [INPUT] to parameter setup window

or next menu selection window. It displays like followed window:

Then suppose you select menu item Display Contrast, it displays

like this:

Press [INPUT],then it enters into Display Contrast Window, and

window is as followed:

Press [INPUT] to save while [] to main window

Cargo Name [123]

ValueSteel Code:0

(Input cargo name)

[]Back [INPUT] Confirm

Prnt Setup Display Contrast

Comm Setup Cargo No. Enable

Date/Time Setup Vehicle No. Enable

Date/Time Display []Back [INPUT] Confirm





Display Contrast [123]

Value4

(Input range:0~5)


10

5.3 Menu Operation

5.3.1 Cargo Name Window Setup

Press [Cargo No.] at weighing mode, it displays:

Press [INPUT],

After input cargo name and press [INPUT], indicator will search

whether corresponding code exits, if exits, then it displays

the right code, if not exit, then it creates new code and

displays. If user knows code, then first input code, then

indicator will search the right corresponding cargo name

according to the input code. If indicator cant search the right

cargo name according to code, then it displays error.

Then press [INPUT] to save while [] to main window

Note:

5.3.2 Vehicle No./ Tare Setup

Press [Vehicle No.] or [SAVE TARE] at weighing mode, it

displays:

Press [INPUT],

Press [INPUT],

Input area Input mode Note

Cargo Name 123/ABC/PINYIN/SIGN Max. 10 character

Code 123 Max 3 character

Cargo Name [123]

Cargo NameSteel Code:1

(Input cargo name)


Cargo Name [123]

Cargo NameSteel Code:1

(Input cargo name)


Vehicle No./ Tare [123]

Vehicle No.A12345 Code:0

Tare:1000 kg




Tare:1000 kg


11

After input Vehicle No. and press [INPUT], indicator will

search whether corresponding code exits, if exits, then it

displays the right code, if not exit, then it creates new code

and displays. If user knows code, then first input code, then

indicator will search the right corresponding Vehicle No.

according to the input code. If indicator cant search the right

Vehicle No. according to code, then it displays error.

After input Vehicle No. and code, it will automatically go to

tare set, the tare value is just the tare of the vehicle. If

there is no save, then tare is regarded as 0; if need to change

the tare, then input by 123eric key and press [INPUT] to save,

while [] to main window

If code is 0, it indicates that just weigh for cargo, tare cant

be input.

5.3.3 Input Vehicle No./ Cargo No. Setup (Save and print setup)

Press [SAVE PRINT] at weighing mode, it displays:

Press [INPUT],

Press [INPUT],

Press [INPUT],


Vehicle No. 123/ABC/PINYIN/SIGN Max. 10 character

Code 123 Max 3 character

Tare 123 Max 6 character



Tare:1000 kg


Input Vehicle No./ Cargo No. [123]


Cargo No.:--- kg Code:1














12

After input Vehicle No./Cargo NO. and press [INPUT], indicator

will search whether corresponding code exits, if exits, then

it displays the right code, if not exit, then it creates new

code and displays. If user knows code, then first input code,

then indicator will search the right corresponding Vehicle

No./Cargo No. according to the input code. If indicator cant

search the right Vehicle No./ Cargo No. according to code,

then it displays error.

After 4 input area all finished, press [INPUT] to save and

execute print, while [] to main window

5.3.4 Preset Tare Setup

Press [TARE PRESET] at weighing mode, it displays:

Press [INPUT] to save while [] to main window. If preset tare

is not zero, then indicator displays net weight and net light

is on; if preset tare is zero, then it displays gross weight.

If preset tare value is not integer times of division, then

it will round integer times of division

5.3.5 REP PRINT Setup

Press [REP PRINT] at weighing mode, it displays:

Press [][ ] to select the report format. When select Daily

report and press [INPUT], it displays:


Vehicle No. 123/ABC/PINYIN/SIGN Max. 10 character

Code(up) 123 Max 3 character

Cargo No. 123/ABC/PINYIN/SIGN Max. 10 character

Code(down) 123 Max 3 character


Tare 123 Max. 6 character


Tare 123 Max. 6 character

Input area Note

Daily Report Print weighing records by date, 3

shares in different forms

General Report 1~

General Report 6

Print all weighing records in 6

formats. Format, refer to appendix Preset Tare [123]

Tare:0.000 kg

(Input preset tare value)


Daily Report General Report 4

General Report 1 General Report 5

General Report 2 General Report 6

General Report 3 []Back [INPUT] Confirm

13

After input the report date and press [INPUT] it prints out

all records related to the date and back to weighing mode when

printing finishes. Press [] to main window;

When selects the other report format and press [INPUT], it

prints corresponding reports and back to weighing mode; Press

[] to main window;

5.3.6 CALIBRATE Setup

First open the PB seal socket and turn on the calibration

switch .Press [CALIBRATE] at weighing mode, it displays:

After input the right password, and press [INPUT], it directs

to calibration setup window. If password is not right, it

requires to input again after alarm. If you input the wrong

password by 3 times, then it back to weighing mode. Press []

to main window;

Calibration Setup Window

Press [][ ] to turn page:

IDT Calibrate

After select this menu item and press [INPUT], it directs to

the course of calibration:


Date 123 From left to right,

year/month/day, 2 digits for

each item


PWD 123 6 digit password,

default is 888888

Repot Date [123]

Date:06/08/31

(Input the record date you want to print)


Calibrate PWD [123]

PWD:******

(Input correct calibration password)


IDT Calibrate LOCEL Type

Angel Adjust Unit

LOCEL Calibrate Zero Track Range

LOCEL Address Change []Back [INPUT] Confirm

Manual Zero Range

Auto Zero Range

Dgtl Filter Int.

Calibrate P of IDT []Back [INPUT] Confirm

14

First, it displays the division setup window:

After division input and press [INPUT], it displays the decimal

point setup window:

After decimal point inut and press [INPUT], it displays the

full capacity(F.S) setup window:

After F.S. input and press [INPUT], it displays the zero point

calibration window:

Press [INPUT] after AD code is stable while there is no load,

then indicator come to load point calibration window:

After weight is loaded and input by 123eric key, press [INPUT]

when AD code is stable, then it returns back to main menu window

When AD code changes in a small range, then its stable


Decimal point 123 0,1,2,3,4


F.S. 123 Max. 6 character


Division 123 1,2,5,10,20,50 optional


Load 123 Max. 6 character

Division [123]

Division:1

(1,2,5,10,20,50 optional)


Decimal Point [123]

Decimal Point:3

(From 0~4)


F.S. [123]

F.S.:200.000 kg

(Input the full capacity)


Zero point (AD code of LOCEL)

1569 []Back [INPUT] Confirm

Load:200.000 kg [123]


15

Angel Adjust


the course of angel adjust, it displays the Angel Adjust window:

:

Press [][ ] to select the method, and press [INPUT] to confirm;

Note: When load cell is changed, then select manual method to

adjust and setup the relationship of load cell quantity and

address.

Manual method

First, it comes to Quantity of LOCEL window

After input quantity of load cell, press [INPUT], it directs

to LOCEL Address window:

After input address, press [INPUT], it directs to Coefficient

Adjust window. Press [], then it back to Angel Adjust window.

After coefficient is input, press [INPUT] it directs to LOCEL

Address window, Press [], then it back to Angel Adjust window.

In manual method, the cycle 123ber of the two parameters is

decided by the quantity of load cell. When all setup is finished,

it back to Angel Adjust window or press [WEIGH] to weighing

mode.

Input area Note

Manual method Adjust the angel according to known adjust rate

Auto method Adjust the angel according to adjust rate by the

loaded weight


Coefficient 123 6 digits, from .50000~2.00000


Quantity 123 2 digits, from 1~16


Address. 123 2 digits, from 0~63



Manual method

Auto method


Quantity of LOCEL [123]

Quantity:8

(From 1~16)


LOCEL Address (01/08) [123]

Address.:1

(From 0~63)


Coefficient Adjust [123]

Coefficient:1.00450

(From 0.50000~2.00000)


16

Auto method

First, it comes to Quantity of LOCEL window

After input quantity of load cell, press [INPUT], it directs

to Load Weight window:

After load weight and wait until platform is stable, press

[INPUT], it directs to LOCEL ISN window:

After ISN is stable, press [INPUT] it directs to next load weight

window.

Repeat load weight operation, when it reaches the load weight

times(equal to load cell quantity), press [INPUT], indicator

finishes angel adjust.

LOCEL Calibrate

As different load cell supplier offers different load cell

calibration method, hence here only YAOHUA load cell

calibration method is listed. If load cell is not YAOHUA, then

indicator goes back to main window after alarm.

Note: When calibrating for load cell, indicator could only be

connected to 1 pre-calibrate load cell.


the course of load cell calibration, it displays the No. of

LOCEL window:

:




No. 123 2 digits, from 1~16

Quantity of LOCEL [123]

Quantity:6

(From 1~16)


Load Weight (01/08)

(Load weight at assigned location of

platform)


LOCEL ISN(01/08)


Load Weight (02/08)

(Load weight at assigned location of

platform)


No. of LOCEL [123]

No.:1

(From 1~16)


17

After input NO. of load cell and press [INPUT], it displays

the Zero Point of LOCEL window:

Press [INPUT] when there is no load, it directs to 50% F.S.

of LOCEL window after indicator its stable. If indicator didnt

search any load cell, then it returns back to weighing mode

after alarms.

Press [INPUT] when its at 50% F.S. of LOCEL, it directs to

F.S. of LOCEL window after indicator its stable.

Press [INPUT] when its at F.S. of LOCEL, it returns to weighing

mode.

LOCEL Address Change


LOCEL Address Change window:

When changing address for load cell, indicator could only be

connected to 1 load cell. Input new address and press [INPUT],

it directs to LOCEL ISN window


Value 123 Max. 6 digits, without

decimal point


Value 123 Max. 6 digits, without

decimal point


Address 123 2 digits, from 0~63

Zero Point of LOCEL

(Press [INPUT] at no load)


50% F.S. of LOCEL [123]

Value: 2000

(Press [INPUT] after 50% F.S. is loaded)


F.S. of LOCEL [123]

Value: 4000

(Press [INPUT] after F.S. is loaded)


LOCEL New Address [123]

Address: 1

(From 0~63)


LOCEL 01 ISN


18

Press [INPUT] to main menu, while [] to main window

LOCEL Type


LOCEL Type window


UNIT


UNIT window

Press [INPUT] to save while [] to main win

Zero Track Range


Zero Track Range window


Manual Zero Range


Manual Zero Range window


Input area Note

HBM LOCEL Digital load cell Protocol HBM

YAOHUA LOCEL Digital load cell Protocol YAOHUA

Only 1 LOCEL Digital load cell Protocol ONLY 1

Input area Note

KG KG is the unit

T Ton is the unit


Range 123 2 digits, from 0.0~4.5,

0.5 as the interval


Range 123 3 digits,

0,2,4,10,20,40,100

HBM LOCEL

YAOHUA LOCEL

Only 1 LOCEL


KG

T


Zero Track Range [123]

Range: 0.5 e

(From 0.0~4.5, 0.5 as the interval)


Manual Zero Range [123]

Range: 2.0 %

(0,2,4,10,20,40,100)


19

Auto Zero Range


Auto Zero Range window


Dgtl Filter Int.


Dgtl Filter Int. window


Calibrate P of IDT


Calibrate P of IDT window

Press [INPUT], it directs to the Calibrate Coefficient window:


Range 123 3 digits,

0,2,4,10,20,40,100


Value 123 Max. 6 digits, its only

changed when replace indicator

without re-calibration and

its changed according to the

replaced indicator


Int. 123 1 digit, from 0~4

The bigger the value is,

the better stability and

lower response speed it is


Value 123 Max. 6 digits, its only

changed when replace indicator

without re-calibration and

its changed according to the

replaced indicator

Auto Zero Range [123]

Range: 2.0 %

(0,2,4,10,20,40,100)


Dgtl Filter Int. [123]

Int.: 2

(From 0~4)


Zero Point [123]

Value: 2145

(Input AD code at zero point)


Calibrate Coefficient [123]

Value: 0.44336

Input Calibrate Coefficient)


20

Note: The menu also directs to check or modification for

calibrated indicator.

5.3.7 Setup Window

Press [SETUP] at weighing mode, it displays:

Press [][ ] to turn page:

Prnt Setup


Function PWD window

Press [INPUT], it directs to Prnt Setup window

Prnt Method


Prnt Method window

Press [input] after select, indicator save the setup. Press

[] to main menu while press [WEIGH] to main window.


PWD 123 6 digits, default is

888888

Input area Note

Auto Prnt Auto print and save current weighing data

Manual Prnt Press [SAVE PRINT]or [SUP PRINT], then it can

print and save current weighing data





Calibrate PWD Change IDT ISN

Timing PWD Change

LOCEL Check

LOCEL Searching []Back [INPUT] Confirm

Function PWD [123]

PWD:

(Input correct function password)


Prnt Method Min. Prnt Weight

Prnter Type Filled Prnt option

Prnt Back Zero Rst Company Name

Prnt Format []Back [INPUT] Confirm

Auto Prnt

Manual Prnt


21

Prnter Type


Prnter Type window

Prnt Back Zero Rst


Prnt Back Zero Rst window

Prnt Format


Prnt Format window

Min. Prnt Weight


Min. Prnt Weight window

Input area Note

Prnt Invalid! Printing function forbidden

Panasonic KX-P1131 Panasonic KX-P1131 printer is chosen

EPSON LQ300K EPSON LQ300K is chosen

EPSON LQ-1600K EPSON LQ-1600K is chosen


Value 123 3 digits, from 0~100, 0 means

print only when indicator is

back to zero; while 100 means

print without any restrict.

Input area Note

Record Format Print report in record format

1 Link Format Print report in 1 link format



Prnt Invalid!

Panasonic KX-P1131

EPSON LQ300K

EPSON LQ-1600K []Back [INPUT] Confirm

Prnt Back Zero Rst [123]

Value: 0 %

(Input restrict range 0~100)


Record Format

1 Link Format

2 Link Format

3 Link Format []Back [INPUT] Confirm

22

Filled Prnt option


Filled Prnt option window

Company Name


Company Name window

Company name can be printed out on weighing bill.

Comm Setup


Comm Setup window

Comm Method


Comm Method window


Value 123 Max. 6 digit, the min. print

weight should be more than 10e,

Input area Note

Fill Format Disable Printer wont adopt fill format

Fill Format Enable Printer will adopt fill format


Name 123/ABC/PINYIN/SIGN Max. 23 character

Min. Prnt Weight [123]

Value: 0.010 kg

(>=10 e)


Fill Format Disable

Fill Format Enable


Company Name [123]

Name: Yaohua Weighing

(Input company name)


Comm Method

Comm Address

Baud Rate


Command Method

Continuous Method


23

Comm Address


Comm Address window

Baud Rate


Baud Rate window

Date/Time Setup


Function PWD window

Press [INPUT], and it directs to

After input date and press [INPUT],it directs to:

Input area Note

Command Method Indicator communicates with PC in

command method

Continuous Method Indicator communicates with PC in

continuous method


PWD 123 6 digits, default is

888888


Address 123 Max. 2 digits, from 1~26


Value 123 Max. 4

digits,600,1200,2400,4800,9600

Comm Address [123]

Adddress:1

(From 1~26)


Baud Rate [123]

Value:1200 b/s

(600,1200,2400,4800,9600)


Function PWD [123]

PWD:

(Input correct function password)


Date/Time Setup [123]

Date:06/08/31

Time:20:16:53


24

Date/Time Display


Date/Time Display window

Display Contrast


Display Contrast window

Cargo No. Enable


Cargo No. Enable window


Date 123 From left to right:

Year/Month/Day

Time 123 From left to right:

Hour/Minute/Second

Input area Note

Display Time Display time at weighing window

Display Date Display date at weighing window

No display No display for time or date at all


Value 123 Max. 1 digit, from 0~5

0 means LCD/VED contrast lowest

5 means LCD/VED contrast highest

Input area Note

Cargo No. Enable Cargo No. can be set up and printed out

Cargo No. Disable Cargo No. cant be set up and printed out

Date/Time Setup [123]

Date:06/08/31

Time:20:16:53


Display Time

Display Date

No Display


Display Contrast [123]

Value:4

(From 0~5)


Cargo No. Enable

Cargo No. Disable

[]Back []Select [INPUT]

Confirm

25

Vehicle No. Enable


Vehicle No. Enable window

Calibrate PWD Change


Calibrate PWD Change window

After input the original password, if password is right, then

it directs to next step of Calibrate PWD Change window, or else

it requires to input again after alarms. Indicator goes back

to main menu after 3 times wrong input.

After input new calibration password and press [INPUT], it

appears again:

The new password input two times should be the same.

Timing PWD Change


Calibration PWD window

Input area Note

Vehicle No. Enable Vehicle No. can be set up and printed out

Vehicle No. Disable Vehicle No. cant be set up and printed out


PWD 123 6 digits,


PWD 123 6 digits,

Vehicle No. Enable

Vehicle No. Disable

[]Back []Select [INPUT] Confirm

Calibrate PWD Change [123]

PWD:

(Input the original calibration password)



PWD:

(Input new calibration password)



PWD:

(Input new calibration password again)


Calibration PWD [123]

PWD:

(Input the correct calibration password)


26

After input the calibration password, if password is right,

then it directs to next step of Timing power off Date window,

or else it requires to input again after alarms. Indicator goes

back to main menu after 3 times wrong input.

LOCEL Check


LOCE NO. window

Input the No. of load cell you want to check and press [INPUT],it

directs to LOCEL ISN window

Press [INPUT], indicator will display ISN of all load cell one

by one.

LOCEL Searching


LOCE Searching window

After search finishes, if there is load cell searched, it

displays:

0101: 01 stands for the No. of load cell while 01 stands for

the address of load cell, the max. NO. of load cell is equal

to the quantity of load cell.


PWD 123 6 digits,


Date 123 6 digits, from left to right:

Year/Month/Day


No. 123 2 digits, from

1~16

Timing power off Date [123]

Date: 99/99/99

(Input the timing date for power off )


LOCEL NO. [123]

No.: 1

(From 1~16 )


LOCEL 01 ISN


LOCEL Searching! Please Wait!

LOCEL Searching( No./Add.)

0101 0202 0303 0404 0505 0606

0707 0808 0909 1010 1111 1212

1313 1414 1515 1616 []Back

27

If there is no load cell searched, it displays:

IDT ISN


IDT ISN window

Check


Check window

Check by Date


Check by date window

After input the date, press [INPUT],it displays:

Input area Note

Check by Date Check record by date

Check by Vehicle No. Check record by vehicle no.

Check by Cargo No. Check record by cargo no.

Check VEHNO of RCD! Check the vehicle no. of the record

Check CARNO of RCD! Check the cargo no. of the record

Check Ovrload Record Check overload records



Year/Month/Day

Non-con!

[]Back

250000 []Back

Check by Date Check CARNO of RCD!

Check by Vehicle No. Check Ovrload Record

Check by Cargo No.

Check VEHNO of RCD! []Back [INPUT] Confirm

Record Date [123]

Date: 06/04/12

(Input the record date for check )


0001/0020 06/04/12 12:32:30

Vehicle NO.:A12345 Cargo No.:Steel

GW:2000kg Tare:50kg

NW:1950kg [] Page Down

28

Press [], it shows the next record by this date:

Press [DELETE] to delete the record while you are checking

Check by Vehicle NO.


Check by Vehicle NO. window

After input the vehicle no. or code, press [INPUT],it displays:

Press [], it shows the next record by this vehicle no.:


Check by Cargo NO.


Check by Cargo NO. window

After input the cargo no. or code, press [INPUT],it displays:

Press [], it shows the next record by this cargo no.:


No. 123/ABC/PINYIN/SIGN Max.10 character

Code 123 Max. 3 character


No. 123/ABC/PINYIN/SIGN Max.10 character

Code 123 Max. 3 character

0002/0020 06/04/12 12:40:30


GW:2050kg Tare:50kg


Vehicle NO. [123]

No.: A12345 Code:0

(Input the vehicle no. of the record )


0001/0020 06/04/12 12:40:30


GW:2050kg Tare:50kg


0002/0020 06/04/12 12:45:30


GW:2050kg Tare:50kg


Cargo NO. [123]

No.: Steel Code:1

(Input the cargo no. of the record )


0001/0030 06/04/12 12:32:30


GW:2000kg Tare:50kg


29


Check VEHNO of RCD!


Check VEHNO of RCD window

Press [] [] to turn page

Check CARNO of RCD!


Check CARNO of RCD window


Check Ovrload Record


Check Ovrload Record window


Delete

After select this menu item, it directs to Delete window

Input area Note

Delete by Time Delete record by time

Delete by Vehicle No. Delete record by vehicle no.

Delete by Cargo No. Delete record by cargo no.

Delete All RCD Delete all record in indicator

0002/0030 06/04/12 12:40:30


GW:2050kg Tare:50kg


0001/0009

Vehicle No.: B12345 Code:001

Tare:0.000kg

[]Back [] Page Down

0001/0004

Cargo No.: Steel Code:001

[]Back [] Page Down

0001/0002

Date:06/11/13 Time:15:26:48

GW:223 394kg

[]Back [] Page Down

Delete by Time

Delete by Vehicle No.

Delete by Cargo No.

Delete All RCD []Back [INPUT] Confirm

30

Delete by Time


Delete by Time window

After input the date, press [INPUT],it displays:

Press [INPUT], then delete the record, press [], then cancel

delete operation

Delete by Vehicle No.


Delete by Vehicle NO. window

After input the vehicle no. and code no, or directly press

[INPUT],it displays:


delete operation

Delete by Cargo No.


Delete by Cargo NO. window

After input the cargo name and code no, or directly press

[INPUT],it displays:


delete operation



Year/Month/Day

Record Date [123]

Date: 06/04/12

(Input the record date for delete )


Record by this time deleted?


Vehicle NO. [123]

No: A12345 Code:1

(Input the vehicle no. of record for delete )


Record by VEHNO. deleted?


Cargo Name. [123]

Name: Steel Code:1

(Input the cargo name of record for delete )


Record by CARNO. deleted?


31

Delete all record


Delete all record window


delete operation

6. Character Input

6.1 Brief Introduction

Xk3190 DS2 supports NUM(123), English(ABC), Chinese (PINYIN)

and Sign to input the character, user can input the required

information through compound inputting. It is quite similar

to the popular cell phones T9 input method. Also Chinese PINYIN

has the function to index the words which have several different

pronunciations, can successfully raise the efficiency.

6.2 Operation

When input VEHICLE NO, CARGO, COMPANY NAME etc, you can use

Number, English, Chinese PINYIN and Sign to mix input the

records, other parameters only support the number input. When

allow compound inputs, press [INPUT MODE] key to switch the

input way. Press [DELETE] key can delete the inputs character

by character.

Screen up-right

corner shows

Input Status

123 Number inputs

ABC English inputs [Capital]

abc English inputs [Small]

PINYIN Chinese PINYIN

.?! Sign

1 Number Inputs

Press the related Number key can input the number

2 English inputs[Capital] / English inputs[small]

First press [INPUT MODE] key to switch the input to English

inputs [Capital] or English inputs [small], after that you can

input the information by press the key which signed the related

letter. E.g. if you want to input letter C, just press key

[1/ABC].

1Continuously press the same character key in 1 second interval,

the input letter will be switched within that keys letter

range.

E.g.Continuously press the key [1/ABC] in 1 second, the

inputted letter will be switched among A.B.C and finally get

one.

2Press the key over 1 second interval, then you will get the

keys related first letter after each press. If u want to input

the other letter of that key, please repeat the 1) operation

to continuously press the same character key in 1 second

interval and select that requested letter.

E.g.: if u want to input HAI, please continuously press [3/GHI]

twice within 1 second and get H, after 1 second press [1/ABC]

All record deleted?


32

get A, and again after 1 second continuously press [3/GHI] three

times to get I. It is finished.

3 Chinese PINYIN inputs

First press [INPUT MODE] to switch the input to Chinese PINYIN.

1Directly press the key according to the PINYIN sequence of

the required Chinese character, then the bottom part of the

screen will display one or more right PINYIN which match the

request and will show their related Chinese characters.

2 Presskey to select the demanded PINYIN. After

selection, the PINYIN color will be highlighted. (The related

Chinese character will be changed according to Pinyins

selection)

3 Presskey to select the required Chinese character.

After selection the Chinese character color will be highlighted.

(Each row can display 15 Chinese characters. When the quantity

of the character which match the request was exceeding 15,

indicator will automatically turn to next or last row. All

PINYIN and Chinese character can be displayed circularly).

4 When get the required Chinese character, press [INPUT] key,

the indicator will put the selected character to the input area

and the cursor will wait for next inputs. When all inputs

finished, press [INPUT] key to save the inputted characters

which listed inside the input area.

E.g. if you want to input the Chinese word seaChinese PINYIN

was hai, then press the following key3/GHI1/ABC

3/GHI by sequenceno need to care about the time interval.

The bottom of the screen will display two PINYIN which match

your type, that is gaiand hai. Presskey to select hai,

you can find out the related Chinese character at bottom of

the screen. Presskey twice to select Chinese character

sea and finally pressINPUT to put sea to the input area.

4 Sign inputs

First pressINPUT MODEswitch to Sign inputs

1 The bottom of the screen will display all the signs waiting

for your selection. Pressto select the required signs,

after select the signet color will turn to highlighted. Press

INPUTKeyIndicator will put the selected signs into the

input area, and automatically turn back to the PINYIN inputs

waiting for input another Chinese Character.

2 If u want to continue input the signs, please pressINPUT

MODEkey to switch the input status, select Sign and input the

required sign. When finish the inputting please press [INPUT]

to save the information inside the input area.

E.g.If you want to input pressINPUT MODEswitch to

the sign inputs. The bottom of the screen will display a series

of the signs, press 5 times to get ?, pressINPUT

key to put the into the input area. At the same time the

input status back to PINYIN inputs.

Chapter 7 Calibration

7.1Calibration Setting

First turn on the seal baseadjust the inside calibration switch

to allow the calibration. In weighing modepress9/YZ

Calibrate,the indicator shows:

33

After input the correct password, pressINPUTto enter the

Calibration setting window. If the password inputted is wrong,

system will ask user to re-input, indicator will automatically

back to weighing mode after 3 times continuously wrong typing.

Also you can pressto directly back to weighing mode.

Calibration setting window

Presskey to page up and down

First we should make the angel adjustment, the detail as

follows:

1Angel adjustment

Pressto select corners difference adjustment item

inside the calibration setting windowpressINPUTto enter

the corner difference adjustment window.


Set the

password

value

Number Input 6 digit password, each* means

1 digit.

If input the number over 6 digit,

indicator only keep the first 6 digit.

Default password is 888888

Settings Set description

Manual Use the available load cells adjustment

coefficient to adjust the corners difference

Auto Through adding the weight, indicator will

re-calculate the load cells adjustment

coefficient to adjust the corners difference.

Calibration PWD 123

Value******

(Use Number key to input the right

Calibration PWD)

RETURN INPUTOK

IDT Calibrate Locel type

Angel adjust Weighing unit

LOCEL calibration Zero track range

LOCEL Address Change select INPUTOk

Manual zero range

Auto zero range

Dgtl filter Int

Calibrate P of IDT select INPUTok

Suppose the digital load cell had calibrated before send out,

and was connected correctly with the indicator. Also we select

the right brand of the load cell in Type of the LOCEL setting

menu,if not setplease refer to Chapter four Menu set up

to do the related settings.

Manual

Auto

return select INPUTok

When you know the digital load cells adjustment coefficient,

you can use manual setting. This way is normally applied to

the situation when changing a new indicator and no need to

re-calibrate it with the weight. The detail operation can refer

to Chapter four, here we only introduce how to automatically

adjust the angel difference.

34

Presskey to chooseAutopressINPUTkey to enter LOCEL

quantity setting window.


Set value Number Can input 2 digit number maximum,

LOCEL quantity was limited within

116pcs

After input the Load cell quantity, pressINPUTkey to enter

weight loading operation, if u presskey, indicator will

back to the previous window:

Load the weight onside the instructed position of the platform,

after load for a while when stable, pressINPUTkey to enter

the LOCEL inner code window:

After ISN stable pressINPUTindicator will mention you to

enter the next weight loading status:

Load the weight circularly to finish the operationwhen reach

the regulated loading times,(loading times equals to the LOCEL

quantity which you set)pressINPUTkeyindicator will finish

the corner difference adjustment and return to the upper menu.

If you presskey during the corner difference operation

then the operation will be canceled and return to the upper

menu.

After finish the Angel adjustment, the indicator start to

calibrate, the details listed below:

7.2. Calibration

In standard setting windowpressto move the highlight

on to termIndicator calibrationpressINPUTto enter into

Calibration window.

First show you the division setting,

Quantity of LOCEL 123

Value8

(Input range116)

Return INPUTok

Load weight (01/08)

(load the weight onside the

instructed position of the

platform)

Return INPUTOK

Load weight (02/08)

(load the weight onside the

instructed position of the

platform)

Return INPUTOK

LOCEL ISN (01/08)

1998202

Return INPUTOK

Division 123

Value1

(1,2,5,10,20,50 optional)

Return INPUTOK

35

After the division setting pressINPUTto set the decimal

points

Input area Input Mode Note

Value Number Decimal points only accept the

input of 01234Other number

input will be error alerted.

After input the digit rates, pressINPUTto enter F.S settings,


Value Number Allow to input 6 BITS number maximum

After input the F.S, pressINPUTto enter Zero confirm window,

Under no load status waiting for the A/D code stable then

pressINPUTindicator enter into load weight window.

Please load the standard weight, input the related weight value

and waiting for the A.D code getting stablethen pressINPUT

key to finish the calibration. Indicator will return to the

standard calibration window.

PressWeighingkey to return to the weighing mode. If the LOCEL

does not have the problem, you can get the accurate weight at

present. Please note if the AD code not drift too muchwe can

assume the AD code is stable.


Value Number The divisions only accept the

input of 125102050Other

number input will be error

alerted


Value Number Allow to input 6 BITS number maximum

Decimal points 123

Value3

(0,1,2,3,4 optional)

Return INPUTOK

F.S 123

Value200.000 kg

(Input the F.S value)

Return INPUTOK

Load weight200.000 kg 123

298568

Return INPUTOK

Zero (LOCEL A/D code)

1569

Return INPUTOK

Normally, after the above steps, indicator calibration was

finished!! Other measurement parameter should be following the

indicators default set. If you want special requirement, please

set accordingly refer to Chapter four.

36

Chapter 8 Communication

8.1Serial communication interface

XK3190DS2 weighing indicator can communicate in data with PC

through serial communication interface. The communication mode

includes continuous mode and command mode. In command mode one

PC can communicate with several indicators.

8.1.1 Connection:

. The communication interface is a 15 pin RS232 socket.

The signal of each pin is detailed in figure 7-1 (pin

6, 7, 8.for RS232C; pin 1, 2,3,4,8 for RS422C). The serial

communication shares the same socket with scoreboard.

. The 4-pin shield wire is recommended.

Figure (8-1) Serial communication output and scoreboard

interface

8.1.2 Signal parameter

. Signal: RS232/RS422/RS485

. Baud rate: 300/600/900/1200/2400/4800/9600

. Address: 26 (A ~ Z)

8.1.3. Continuous mode for serial communication

The data sent are the current weight which the indicator

shows(G.W or N.W)each frame including 12 group of data, the

format listed below:

N Related contents and the notes

1 02(XON) BEGIN

2 +/- SIGN

3 Weight information HIGH


Weight information

Weight information

8 Weight information LOW

9 Decimal points RIGHT TO LEFT04

10 XOR CALIBRATON 4 BITS HIGH

11 XOR CALIBRATION 4 BITS LOW

12 03(X0FF) END

Note

! Make sure that communication interface output lead and

computer are correctly connected, if there is something

wrong with connection, damage will happen to output port

of instrument and input port of computer, sometimes, the

damage is so big that instrument and, computer and

corresponding peripherals are got involved

! Necessary computer technology and programming expertise

are required for computer communication, which should be

participated and instructed by professionals.

Non-professional staff is supposed not to be involved in

this regard.

This connection way was only suitable for the factorys

communication protocolif the customers have their own special request, please set the wire according to chapter

ones detail!

37

XOR23 89

8.1.4. Command mode for serial communication

Indicator sends out the related data according to the upper

apparatus command. Each command sends out, indicator will send

one frame of data.


1 02XON Begin

2 AZ Address

3 AI Command AShaking hands

Command BRead gross weight

Command CRead tare

Command DRead net weight

Command EGet truck number

Command FGet goods number

Command GDelete all records

Command HZero

Command ITare

4 XOR Calibration High 4 bits

5 XOR Calibration Low 4 bits

6 03XOFF END

Output contents of the indicator


1 02XON Begin

2 AZ Address

3 AI Command AShaking hands

Command BOutputting gross weight

Command COutputting tare

Command DOutputting net weight

Command EOutputting truck number

Command FOutputting goods number

Command GNone

Command HNone

Command INone

4 Outputting proper data according to command





Outputting proper data according to command

Outputting proper data according to command

N-1 Outputting proper data according to command

N Outputting proper data according to command

N+1 XOR Calibration High 4 bits

N+2 XOR Calibration Low 4 bits

N+3 03XOFF END

The output contents (4n) Command A None Each frame including 6

sets of data

Command B Gross weight: Each frame including 14

sets of data 4 Sign (Positive or

negative) 511 Gross

Weight6 bits and 1 bit decimal

Command C Tare Each frame including 14 sets of data 4 Sign

(Positive or

negative) 511 Tare6 bits

and 1 bit decimal Command D Net weight Each frame including 14

sets of data 4 Sign (Positive or

negative)

38

511 Net Weight6 bits and 1 bit decimal

Command Outputting truck number 413: 10 Characters

Total output 16

characters Can including Chineseone Chinese take up two

characters, If truck number was less

than 10 characters, you

could use space to

compensate

Command Outputting goods number:

413: 10 Characters

Total output 16

characters Can including Chineseone Chinese take up two

characters, If goods number was less

than 10 characters, you

could use space to

compensate

XOR231011

NOTE. The definition of the higher or lower 4 bits for the

XOR calibration.

If the higher 4 or lower 4 bits for the XOR calibration is not

more than nine, you should add 30h and have it transmitted into

ASCII code. Otherwise, you should add 37h and have it

transmitted into alphabet ASCII code. For example, when the

higher 4 bits for the XOR calibration is 6, you can add 30h.

Obviously 36 will be transmitted as ASII code 6. Also, when

the higher 4 bits for the XOR calibration is B, you can add

37h, and 42h will be transmitted as ASCII code B

8.2 CONNECT INDICATOR WITH SCOREBOARD

8.2.1 The scoreboard interface adopts 15pin D type socket (share with the serial communication interface. (Ref. Figure

8-1, pin 9 and pin 10)

(This way was current loop output, and was the standard wire

connection after products were finished)

8.2.2 The current loop signal of the scoreboard is 20mA, output

is binary serial, and the baud rate is 600. Each frame of

date has 11 bits, including one initial bit (0), 8 data bits

(the lower one precedes the higher), one sign bit and one

stop bit.

8.2.3 A set of data is transmitted every 100ms, including 3

frames of data. (Ref. figure - 8-2).

Make sure that scoreboard and output leads are connected

correctly. If there is something wrong with connection,

damage will happen to output port of instrument and input

port of scoreboard, sometimes, the damage is so big to

influence the instrument and scoreboard. Only specially

provided connecting cable is allowed to be use.

39

Figure823 frame of data

Data of the first frame:

The sign bit is zero

X: D0, D1,D2 -------positions of decimal point (0-4)

Y: D3 ------------------weight sign (1-negative, 0-positive)

D4 ---------------------standby bit

G18-G16: ------data of the weight

Data of the second frame:

The sign bit is zero

G15~G8: data of the weight

Data of the third frame:

The sign bit is one

G7~G0: Data of the weight

G0~G18: 19 binary bits for the weight from lower to higher bit.

Chapter 9 Print and record operation

9.1 connect to the Printer

9.1.1 The printer interface is standard paralleled output and

adopts 25-pin RS232 socket. Hereunder is the definition of 25

pins socket. (Ref. figure 9-1)

(Figure 9-1) Printer signal

40

9.2 Save and print the weighing record

9.2.1Indicator allows the truck number and the goods number

to 10 characters (1 Chinese take up 2 characters). It can save

1000 truck number and 1000 goods number maximum.

9.2.2The indicator saves and prints data simultaneously.

Namely, while saving each full set of records, it will print

them out in the meantime. (If the PRINT SET is enabled.)

9.2.3. There are three methods for saving data.

i. Empty-truck saving fist, then full-truck saving. Or

full-truck saving first, then empty-truck saving. It

means a full set of records will be constituted through

saving twice.

ii. When weighing a full-truck and having the knowledge of

the tare previously, saving once is enough to constitute

a full set of records.

iii. When weighing the goods instead of the truck on-loaded,

saving once can usually constitute a full set of records.

9.2.4. Saving and printing procedures

In weighing mode, pressSAVE PRINTindicator enters the below window:

NotePrint function cannot be put into use until properly set.

1. The output lead of the printing interface in the indicator must

be connected to the printer accurately and only specially

provided printer connecting wire is allowed to be used.

Otherwise, the indicator output port and the printer input port

will be damaged, sometimes, the damage is so big that the

instrument and printer are got involved.

2. Before using the printer, please make sure that the cable is

correctly connected at first, and then turn on instrument, in

the end, power on printer. After printing, power off printer

at first, then turn off instrument, in the end, takes off the

cable. If the order is reversed, damage may happen to instrument

and printer.

3. Please choose the recommended printers, in that there are a

great variety of printers with different performances and

compatibilities.

4. Printer must be connected to ground; otherwise, damage will

happen to indicator and printer.

5. Printer signal earth is prohibited to be connected with the

power earth, otherwise will seriously damage the indicator as

well as the printer

In order to identify the three cases mentioned above, the

following assumptions are made in XK3190DS2 indicator:

1 If 0 is set for the truck number, it indicates that the

weighted is not a truck with goods, but the goods. Tare cannot

be set, it should be 0 only. The related truck number also cannot

be deleted, when indicator display or printing the truck number

will be shown as ----------

2 If the indicating light of TARE is on, it means the tare has

been informed. Therefore, saving once could constitute a full

set of records.

3 If the truck number is not zero, together with the indicating

light being off (In gross weight display mode), You need save

twice to constitute a full of set of records.

41

After input the vehicle No., please pressInputkey

The code was automatically get according to the vehicle No.,

if you do not input the vehicle No. before, you can input the

CODE here, then pressINPUTkey

After input the Cargo No.pressINPUTkey

The code was automatically get according to the Cargo No.,

if u do not input the Cargo no. before, you can input the CODE

here, then pressINPUTkeyindicator will save and print.

NOTE:

(1) When input area show highlight, it means you can input data

here. You can chose to input the data in Vehicle/cargo no. and

the CODE area.

(2If you input the data inside the area of Vehicle/cargo no.,

after pressINPUT, indicator will automatically check if any

related code existed inside the Ram. If yes, then indicator will

display the related code; if no, indicator will automatically

make and display a new code. If the user knew the code related

to vehicle/cargo no., you can directly input the code inside

the code area and the indicator will automatically check the

related vehicle /Cargo No. and display them, this can avoid the

relatively complex inputting. Vehicle/Cargo No. can be mix

inputted among English/PINYIN/Number, pressINPUT MODEkey can

switch the inputting mode. After finish the inputting inside

four areas, pressINPUT to save the record and getting print.


Vehicle no Number/English/PI

NYIN/Sign

Maximum 10 characters1

Chinese take up 2 characters

Code (V) Number Maximum 3 bits number

Cargo no Number/English/PI

NYIN/Sign

Maximum 10 characters1

Chinese take up 2 characters

Code (C) Number Maximum 3 bits number

Input vehicle No./tare 123

Vehicle No.xxxx CODE1

Cargo No.--- CODE1

Return InputOK

Input vehicle No. /tare 123


Cargo No.--- CODE1

Return InputOK



Cargo No.--- CODE1

Return InputOK



Cargo No.--- CODE1

Return InputOK

42

If you presscan cancel the printing and return to the weighing

mode.

(3 Saving data could be set with or without Vehicle

number(detail set can refer to the Chapter Four). If you save

the data without the Vehicle No, then the Vehicle no. will be

Zero and cannot be changed.

4Saving data could be set with or without Cargo number(detail

set can refer to the Chapter Four). If you save the data without

the Cargo No, then the Cargo no. will be Zero and cannot be

changed.

5You can not save the record when weighing record unstable or GW0 or NW0.

9.2.5. Automatic saving and printing

1. The print setting for automatic saving is detailed

in PRINT SETTING section.

2. While automatic saving and printing, saving twice

mode does not exist.

3. When automatic saving, Vehicle number and goods

number saved are those set before.

4. Three conditions listed below for the value of

automatic saving:

. When the indicating light of TARE is on, the

current value will be saved into the set of

records.

. When the indicating light of TARE is off, the

indicator will automatically search its

memory for the right tare value corresponding

to the vehicle number and save it into the

set of records.

. When the indicating light of TARE is off and

the tare value corresponding to the vehicle

number does not exist, 0 would be saved as

the tare value in the set of records.

9.2.6. If the vehicle numbers are more than 1000, the indicator

will display RCD FUL!, you should delete some Vehicle number

or all the records refer to 8.3. If the records surpass 1000,

the indicator will delete the earliest one automatically.

9.3Examples for Print operation

9.3.1One time preset tare and print the weight bill

Step Situation Operation Display Note

1 Cargo

loaded

Press key

[tare

preset]

Preset tare

Setting

interface

2 Input

Preset

tare

E.g1000 Set value1.000 kg

3 pressINPUT Save value, preset tare

effective

4 press back to weighing mode

5 presssave print

Inputting

vehicle

no./cargo

no.

interface

6 Inputting

vehicle

No.

E.g.A1245 pressInputto save

Vehicle

No.A1245 If you want to

keep the

original

vehicle no.

please

directly

press

43

INPUT. 7 pressINPUT Enter CODE

area 8 Input

Vehicle

No. CODE

1If you do not input

the vehicle

NO.

Please input

the code.

2. If you

input the

vehicle No.

then no need

to input

code.

CODE1 1If you input the vehicle

No. the code

Will

automatically

got. Press

INPUT go to next step 2If you do not input the

vehicle

number,

please input

here.

9 pressINPUT Start to set the cargo

no.

10 Input

The

Cargo

number

E.g.Iron pressinputto save

Cargo No.Iron

If you want to

keep the

original

cargo

number,

please

directly

press

INPUT key 11 pressINPUT Enter CODE

area

12 Input

Cargo

No.

CODE

1If you do not input

the cargo

no. please

the code. 2 If you input the

cargo no.

then no

CODE0 1If you input the vehicle

No. the code

will

automatical

ly got.

Press

INPUT go to next

need to

input

code.

step 2If you do not input the

vehicle

number,

please input

here.

13 pressINPUT save the code

and start to

print

9.3.2 One time manual operation to print the weight bill Step Situation Operation Display Note

1 PressSAVE

PRINT

Vehicle

No./Carg

o No.

Inputtin

g

Press the key in

the weighing

mode.

2 press

INPUT

No need to input

the vehicle

number,

directly press

theINPUTkey

to enter the

code area:

3 Input

vehicle

number zero

Inputting

0

Code0 Vehicle

No.0was

fitted to

express the

weight of the

goods, this

vehicle no.

44

cannot be

deleted

4 press

INPUT

Save the code

and entering

the cargo no.

setting

5 Input cargo

No.

E.g.:

steel

press

INPUTto

save

Cargo

No.:

steel

pressINPUTto

use original

cargo No.

6 press

INPUT

enter code

program

7 input cargo

No. code

1 input

code if

cargo No.

was not

inputted

2 skip

this step

if cargo

No. was

inputted

code0 1 code will be

generated

automatically

if the cargo No.

has been

inputted, press

INPUTto skip

2.Input code if

the cargo No.

was not inputted

8 press

INPUT

save the code,

start to print

weighing ticket

9.3.3 print weighing ticket(two storage method, loaded

vehicle after empty vehicle, or empty vehicle after loaded

vehicle)

step situation operation display Note

1 Prepare the

empty

vehicle(unti

l the stable

light on)

pressSAVE

PRINT

input

vehicle

No./Cargo

No.

Press keys

on the

weighing

mode.

2 input new

vehicle No.

E.g.: A1245

pressINPUT

to save

vehicle

No.: A1245

press

INPUTto

use the

original

vehicle No.

3 pressINPUT enter code

program

4 input

vehicle No.

code

1.input code

if the

vehicle No.

has not been

inputted

2 skip this

step if the

vehicle No.

has been

inputted

code1 1 the code

will be

generated

automatica

lly if the

vehicle no.

has been

inputted,

press

INPUTto

skip

2Input the

code if the

vehicle No.

has not

been

inputted

45

5 pressINPUT save the

code, enter

cargo no.

setting

6 input cargo

no.

e.g.: steel

pressINPUT

to save

cargo no.:

steel

press

INPUTto

use the

original

cargo no.

7 pressINPUT enter code

program

8 input cargo

no. code

1 input code

if the cargo

no. has not

been

inputted

2skip this

step if the

cargo no. has

been

inputted

code 1 the code

will be

generated

automatica

lly if the

cargo no.

has been

inputted,

press

INPUTto

skip

2Input the

code if the

cargo no.

has not

been

inputted

9 pressINPUT the record

is not

save the

code,

complete,

please

complete!

return the

weighing

mode

10 Prepare the

loaded

vehicle(unti

l the stable

light on)

pressSAVE

PRINT

input

vehicle

no./cargo

no.

display the

last

vehicle

no., cargo

no.

11 vehicle no.

input status

pressINPUT Skip

12 vehicle no.

code input

status

pressINPUT Skip

13 cargo no.

input status

pressINPUT Skip

14 cargo no.

code input

status

pressINPUT printing

now! pls

wait

press

INPUTto

print the

weighing

ticket

Note: the operation is the same when the empty vehicle are

weighed after the loaded vehicle

9.3.4 Auto-print the weighing ticket when tare is preset step situation operation display Note

1 follow the

operation

instructio

n of the

menu, set

the print

46

method to

be

auto-prin

t, press

weighto

return the

weighing

mode

2 Input the

preset tare e.g.100 Preset value

100 kg

3 press

INPUT save the

preset

value,

preset tare

is effected

4 press return the weighing

mode

5 prepare the

loaded

vehicle(unt

il the stable

light is on)

display

weight 400 kg

100 vehicle

weight

500,decrea

se tare100

6 Printing now!

please wait

auto-print

the

weighing

ticket when

the weight

is stable

9.3.5 Print weighing ticket use the tare according to vehicle

no.

step situation operation display Note

1 vehicle no.,

tare have

been preset

available

in the

indicator

2 bring the

loaded

vehicle(unti

l the stable

light is on)

Pre

Vehicle

No

Vehicle

no./tare

preset mode

display the

original

vehicle no.

and tare

3 input the

wanted

vehicle no.

e.g. A00123

press

INPUTto

save

Vehicle no.

A00123

if the

original

vehicle no.

matches,

press

TAREto

confirm

4 Press

INPUT

enter

vehicle no.

code

setting

5 input the

wanted

vehicle no.

code

Press

INPUT

1 if the

vehicle no.

has been

imputed,

press

INPUT

directly.

2 if the

47

vehicle no.

has not been

inputted,

then input

it here and

save by

pressing

INPUT

6 PressTARE return the

weighing

mode and

display the

net weight,

NW light on

the weight

after

decreasing

the tare

7 PressSAVE

PRINT

input

vehicle

no./cargo

no.

press keys

in weighing

mode

8 input the new

vehicle no.

e.g.A1245

press

INPUTto

save

Vehicle

no. A1245

press

INPUTto

use the

original

vehicle no.

9 press

INPUT

enter code

setting

10 input the

vehicle no.

code

1 input

code if the

vehicle no.

has not been

inputted

code** 1 the code

will be

generated

automatical

ly if the

2 skip this

step if the

vehicle no.

has been

inputted

vehicle no.

has been

inputted,

press

INPUTto

skip

2 Input the

code if the

vehicle no.

has not been

inputted

11 press

INPUT

save the

code, enter

cargo no.

setting

12 Input cargo

no.

e.g.steel,

press

INPUTto

save

Cargo no.

steel

press

INPUTto

use the

original

cargo no.

13 press

INPUT

enter the

code

setting

14 input the

cargo no.

code

1 input the

code if the

cargo no.

has not been

inputted

2 skip this

step if the

code0 1 the code

will be

generated

automatical

ly if the

cargo no.

has been

48

cargo no.

has been

inputted

inputted,

Documents

DS2 USER MANUAL.pdf