Upload
ahmed-sohel
View
1.226
Download
6
Embed Size (px)
DESCRIPTION
DSR 2013-14_E&M
Citation preview
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
Mech/1 Supply of filter media fine quality sand from any
source having effective size 0.45 to 0.70 and
uniformity coefficient within the limit of 1.3 to 1.7
within premises as per IS 8419 Part-I of 1977
including transportation, loading, unloading,
stacking and for all leads.
Cum 7900.00 7900.00 7900.00
Mech/2 Supply of filter media gravels at the departmental
stores of various sizes from 10mm to 40 mm
including all leads, transportation, loading,
unloading, stacking etc complete.
Cum 8250.00 8250.00 8250.00
Mech/3 Removing of Filter Media Sand and Gravel;
including lifting, stacking the same within 50m lead
from filter house.
Cum 300.00 240.00 240.00
Mech/4 Spreading, drying grading, screening in two
different sizes, sieving and washing old filter sand
and gravel with water as per direction, drying and
stacking near filter house including labour, using
MIDC’s sieves (water supplied by MIDC at free of
cost) etc. complete.
Cum 300.00 240.00 240.00
Mech/5 Filling the old and new gravels and fine sand in the
filter beds properly in grades and layers as required
including all labour and tools and plants etc
complete.
Cum 180.00 160.00 160.00
Mech/6 Conveying and laying of filter media sand from
godown / store to filter box for lead uotp 100 mtr.
Cum 90.00 80.00 70.00
2013-2014
MAHARASHTRA INDUSTRIAL DEVELOPMENT CORPORATION
Mechanical-Filter Media
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/A/1
(a)
Dismantling of point wiring carried out in M.S./
PVC conduit pipe in wall or ceiling (Concealed type)
for light, fan, bell, independent plug point, and
refilling the holes with cement mortar and finishing
with paint putty and repainting to match colour of
the wall painting etc.
Point 5.00 5.00 5.00
Dismantling of point wiring carried out in PVC
conduit/ PVC casing and capping on wall for light,
fan, bell and independent plug point, and re-filling
with paint putty and repainting to match colour of
the wall painting etc.
Point 5.00 5.00 5.00
Note :- Dismantling wires under a) and b) above
will be retained by the contractor and shall not be
reused for MIDC’s work.
Elec/A/2
(a)
Dismantling of 11 KV or 22 KV/33 KV CTPT
combine unit from DP after removing connections
from HV & LV side.
No. 1000.00 1000.00 950.00
(b) Dismantling of single phase 11 KV/22 kV/33 KV CT
or PT unit from DP after removing connections from
HV & LV side.
No. 750.00 700.00 650.00
Elec/A/3 Dismantling the existing distribution transformer /
DG set of any capacity from the plinth/pole safely
without any damages and storing in safe place.
KVA 12.00 12.00 12.00
Elec/A/4 Dismantling the existing pole with brackets, clamps,
insulators or stay from the cement concrete
foundation and making the site clear by refilling the
pits with excavated materials and bringing it to the
ground level.
a) HT Pole No. 450.00 430.00 430.00
b) Street Light Pole No. 350.00 350.00 330.00
Elec/A/5 Dismantling the existing overhead line of all sizes
without damaging and making the coils in suitable
sizes and stacking at site.
Per
conduc
tor per
Km.
600.00 575.00 550.00
Removing HT/LT/XLPE underground cables without
damaging from the trenches including required
excavation and refilling the same and making the
coils in suitable sizes and stacking at site.
(a) HT XLPE cable. R.M 50.00 50.00 45.00
(b) LT cable up to 70 Sq.mm. R.M 25.00 25.00 22.00
(c) LT cable above 70 Sq.mm. R.M 30.00 30.00 28.00
Elec/A/6
Electrical-A-Dismantling
(b)
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Note - The item No. Elect/A/6 (b) shall be
considered only when the cost of dismantled cable
i.e. scrap value is more than the cost of dismantling.
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/B/1
(a)
Servicing and overhauling of motors, including
removing from location, dismantling cleaning the
winding, drying, applying, varnish, baking, changing
the bearing if necessary (bearing will be supplied by
MIDC) greasing the bearing, assembling, and giving
satisfactory trials on No load and full load etc.
1. 415 volts, 3 phase upto 5 HP No. 432.00 360.00 360.00
2. 415 volts, 3 phase upto 6 HP to 10 HP No. 792.00 720.00 720.00
3. 415 volts, 3 phase upto 12.5 HP to 20 HP No. 1440.00 1296.00 1296.00
4. 415 volts, 3 phase upto 25 HP to 35 HP No. 2304.00 2160.00 2160.00
5. 415 volts, 3 phase upto 40 HP to 50 HP No. 3024.00 2880.00 2880.00
6. 415 volts, 3 phase upto 60 HP to 100 HP No. 3888.00 3600.00 3600.00
7. 415 volts, 3 phase upto 125 HP to 200 HP No. 4800.00 4320.00 4320.00
8. 415 volts, 3 phase upto 225 HP to 300 HP No. 5400.00 5040.00 5040.00
9. 415 volts, 3 phase upto 300 HP to 400 HP No. 6600.00 5760.00 5760.00
(b) 415 volts, 3 phase upto as above 3.3 KV motors
500 HPto 750 HP.
No. 32400.00 30240.00 30240.00
Elec/B/2 Servicing of LT OCB/ACB including checking,
opening, replacing of oil, adjusting the coils,
replacing of damaged spares (spares and oil to be
supplied by MIDC) etc.
a) 415 volts LT OCB/ACB, No. 576.00 576.00 558.00
100 Amp to 300 Amp.
b) 415 volts LT OCB / ACB, No. 746.40 746.40 732.00
400 Amp to 800 Amp.
c) 415 volts LT OCB / ACB, No. 901.20 901.20 888.00
800 Amp to 1250 Amp.
d) 415 volts LT OCB / ACB, No. 1108.80 1108.80 1092.00
1600 Amp to 2000 Amp.
Elec/B/3 Testing and calibrating of electromagnetic relays
and Electrostatic all kind of relays such as overload,
earth fault, directional, motor protection auxiliary
relays etc.
No 1152.00 1152.00 1094.40
Electrical-B-Servicing of Motors, OCB & Relays
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/B/4 Overhauling & Servicing of monorail/trolly
electrically operated overhead cranes with
oiling, greasing, adjustment & alignment of
breakshoes, electomagnetic switches, pendant
instrument clusters, longitudinal; cross & vercal
travels, ON/OFF i.e., start/ stop mechanism, wire
ropes, chain pulley blocks, slings, safety & or
non reverse rachets, antifriction arrangements
etc. complete with issuance of test certificates
as required by annual inspecting relevant
authorities.
a) Upto 2 M.T. capacity M.T. 2520.00 2520.00 2520.00
b) above 2 M.T. to 5 M.T. capacity M.T. 2400.00 2400.00 2400.00
c) above 5 M.T. to 7.5 M.T. capacity M.T. 2100.00 2100.00 2100.00
d) above 7.5 M.T. to 12.5 M.T. capacity M.T. 1800.00 1800.00 1800.00
e) above 12.5 M.T. to 15 M.T. capacity M.T. 1560.00 1560.00 1560.00
f) above 15 M.T. to 20 M.T. capacity M.T. 1380.00 1380.00 1380.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/C/1 Rewinding and repairs of Squirrel cage induction
motors, 440 V, 3 phase, 50 cycles/sec. 1500 RPM
with B class insulation including baking, varnishing,
painting etc. (The scrap of winding material shall be
retained by rewinder.)
1) 25 HP No 8624.00 8910.00 8910.00
2) 30 HP No 11990.00 11880.00 11770.00
3) 35 HP No 16830.00 16390.00 16280.00
4) 40 HP No 17710.00 17270.00 16830.00
5) 45 HP/ 50 HP No 21010.00 20570.00 19580.00
6) 60 HP No 27060.00 26180.00 25740.00
7) 75 HP No 32560.00 32230.00 31900.00
8) 100 HP No 38830.00 37840.00 37026.00
9) 125 HP No 49720.00 49060.00 48180.00
10) 150 HP No 56100.00 51370.00 51370.00
11) 180/200/215 HP No 66330.00 65450.00 65450.00
12) 225/250 HP No 71940.00 66330.00 66330.00
13) 300 HP No 82280.00 74800.00 74800.00
14) 350/400 HP No 93500.00 85030.00 85030.00
15) 500 HP, 3.3 KV No 487500.00 465000.00 0.00
16) 750 HP, 3.3 KV No 525000.00 0.00 0.00
Note :
1) Add 10% for ‘F’ class insulation in the above
rates, for item 1 to 16 only .
2) Add 20% for higher size of frames such as
CVD 450 frame size in case of 180/200 HP motors,
for item Nos 1 to 14 only.
Elec/C/2 Rewinding of Auto transformers including
dismantling, rewinding with new insulated copper
wire/strips of proper size, varnishing/ backing and
filling with fresh transformer oil, painting assembly
and testing of works and delivery at site.
1) 41 to 60 HP No 13970.00 13530.00 13420.00
Electrical-C-Rewinding of Motors.
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
2) 61 to 80 HP No 16280.00 15840.00 15620.00
3) 81 to 100 HP No 18700.00 18150.00 17930.00
4) 101 to 125 HP No 24200.00 23320.00 22440.00
5) 126 to 150 HP No 26180.00 25630.00 24640.00
6) 151 to 175 HP No 28930.00 28050.00 26840.00
7) 176 to 200 HP No 31790.00 31240.00 30250.00
8) 201 to 250 HP No 40150.00 39710.00 39270.00
9) 251 to 300 HP No 46750.00 46200.00 45980.00
10) 301 to 400 HP No 60720.00 59400.00 59400.00
Elec/C/3 Rewinding of submersible pump motor of all types
and makes upto 15 HP with coated copper wires
and overhauling with minor repairs, testing for the
original speed, HP and no load consumption and
guarantee for one year.
HP 1760.00 1430.00 1430.00
Elec/C/4 Rewinding the motor of the table/pedestal/cabin fan
of all types and make and overhauling including
minor repairs, testing for the original speed with
guarantee for one year including transportation from
site and back.
No 495.00 456.50 456.50
Elec/C/5 Rewinding the motor of the ceiling fan of all types
and makes and over hauling including minor repairs
or replacing bush bearing screws etc and testing for
original speed with guarantee for one year.
a) For 900mm sweep No 495.00 456.50 456.50
b) For 1200mm/1400mm sweep. No 495.00 456.50 456.50
c) Exhaust fan 900/1400 RPM 300 mm sweep. No 495.00 429.00 429.00
d) Exhaust fan 900/1400 RPM 375 mm sweep. No 550.00 495.00 495.00
e) Exhaust fan 900/1400 RPM 450 mm sweep. No 660.00 539.00 539.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/D/1 Point wiring
Point wiring for light/fan/ 5 A socket/call bell points
with 2 x 1.5 + 1 x 1.0 sq.mm copper multistrand
660/1100 V grade PVC insulated wires in 2 mm
thick PVC concealed conduits with MS 16 SWG
switch boards, painted from both sides with white
decolam switch plates, 5 A SP switches 3 pin
Socket. Holders/ Ceiling rose etc complete conduits
in slabs inside the rooms/ areas for light and fans
have been laid and are to be used clipping, making
chase etc wherever required should be considered.
(Material bearing IS mark whereas applicable).
a) Light points/Fan points. Point 660.00 660.00 660.00
b)Call bell points. Point 950.00 950.00 950.00
c) 5 A, 3 pin socket outlets on switchboard. Point 72.00 72.00 72.00
d) 5 A, 3 pin socket outlets independent. Point 660.00 660.00 660.00
Elec/D/2 Point wiring for light/fan/ 5 A socket / call bell points
with 2 x 1.5 + 1 x 1.0 sq.mm copper multi strand
660/1100 V grade PVC insulated wires in PVC
casing and capping/ PVC conduit on wall, or
suitable size with white decolam switch plates, 5 A
SP switches 3 pin socket/holders/ceiling rose etc on
wall or ceiling.
a) Light points/fan points Point 350.00 350.00 335.00
b) Call bell points. Point 375.00 375.00 350.00
c) 5 A, 3 pin socket outlets on switchboard. Point 72.00 72.00 66.00
d) 5 A, 3 pin socket outlets independent Point 330.00 330.00 315.00
Elec/D/3 Mains wiring…
A) Mains wiring for lighting and 15 A point circuits
taken through concealed 2 mm thick PVC conduit
pipes of required dia meter in wall/floor including
necessary chasing.
a) 2 x 2.5+1x1.5 sq.mm Cu multistrand wires. R.M 100.00 100.00 95.00
b) 2 x 4.0+1x1.5 sq.mm Cu multistrand wires. R.M 145.00 145.00 130.00
c) 4x4.0+2 x 1.5 sq.mm Cu multisrand wires. R.M 210.00 210.00 200.00
d) 4 x 6.0 +2 x 1.5 sq.mm Cu multistrand wires. R.M 265.00 265.00 250.00
Electrical-D-Point wiring and mains
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/D/3 Mains wiring…
B) Mains wiring for lighting and 15 A power points
taken through PVC, casing and capping over the
walls.
a) 2 x 2.5+1x1.5 sq.mm Cu multistrand wires. R.M 85.00 85.00 75.00
b) 2 x 4.0+1x1.5 sq.mm Cu multistrand wires. R.M 110.00 110.00 105.00
c) 4x4.0+2 x 1.5 sq.mm Cu multisrand wires. R.M 190.00 190.00 175.00
d) 4 x 6.0 +2 x 1.5 sq.mm Cu multistrand wires. R.M 250.00 250.00 240.00
Elec/D/4 Supplying and erecting PVC insulated wire with 1.1
KV grade with ISI mark laid in provided
conduit/casing-n-caping / pole/ bus bar or any other
purpose with necessary bakelite/ Rubber bushes
sleeve and connected to apparatus in an approved
manner.
A)Alluminum wire
a) 2 x 1.5sq.mm / stranded R.M 26.00 25.00 23.00
b) 2 x 2.5sq.mm R.M 33.00 33.00 31.00
c) 2 x 4 sq.mm R.M 37.00 37.00 35.00
d) 2 x 6 sq.mm R.M 44.00 44.00 42.00
e) 2 x 10 sq.mm R.M 59.00 59.00 55.00
f) 3 x 2.5sq.mm R.M 35.00 35.00 33.00
g) 3 x 4 sq.mm R.M 46.00 46.00 44.00
h) 3 x 6sq.mm R.M 58.00 58.00 55.00
i) 3 x 10 sq.mm R.M 75.00 75.00 72.00
j) 4 x 16 sq.mm R.M 121.00 121.00 116.00
k) 4 x 25sq.mm R.M 165.00 165.00 154.00
l) 4 x 35sq.mm R.M 200.00 200.00 190.00
B) Copperwire
a) 2 x 1.5sq.mm R.M 31.00 31.00 29.00
b) 2 x 2.5sq.mm R.M 50.00 50.00 46.00
c) 2 x 4 sq.mm R.M 77.00 77.00 73.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
d) 2 x 6 sq.mm R.M 138.00 138.00 130.00
e) 2 x 10 sq.mm R.M 220.00 220.00 209.00
f) 3 x 2.5sq.mm R.M 66.00 66.00 63.00
g) 3 x 4 sq.mm R.M 105.00 105.00 100.00
h) 3 x 6sq.mm R.M 190.00 190.00 180.00
i) 3 x 10 sq.mm R.M 325.00 325.00 310.00
j) 4 x 16 sq.mm R.M 550.00 550.00 525.00
C) 1x2.5 sq.mm. Solid alluminum PVC wire in green
colour as earth wire.
R.M 15.00 15.00 14.00
Elec/D/5 Supplying and laying conduit bearing ISI mark with
required accessories for drawing wire and duly
sealed at joints to make the complete piping
erected on wall/ceiling with spaces, saddles,
clamps to pipe complete.
A) Rigid PVC conduit (IS 3419)
a) 20mm dia R.M 28.00 28.00 25.00
b) 25mm dia R.M 37.00 37.00 35.00
c) 32mm dia R.M 61.00 61.00 57.00
d) 50mm dia R.M. 72.00 72.00 66.00
B) PVC Casing - n - caping (BS 4678 part-4)
a) 20mm dia R.M 22.00 22.00 21.00
b) 25mm dia R.M 29.00 29.00 26.00
c) 32mm dia R.M 40.00 40.00 37.00
d) 40mm dia R.M 46.00 46.00 44.00
C) Hot dipped galvanisd steel conduit
a) 20mm dia R.M 110.00 110.00 105.00
b) 25mm dia R.M 145.00 145.00 135.00
c)32mm dia R.M 200.00 200.00 190.00
D) PVC corrugated flexible conduit
a) 16mm dia R.M 8.00 8.00 8.00
b) 20mm dia R.M 10.00 10.00 9.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
c) 25mm dia R.M 13.00 13.00 12.00
d) 32mm dia R.M 17.00 17.00 15.00
Elec/D/6 Concealing of conduit pipe in wall or ceiling with
making grooves and plastering with cement mortar
and finishing the surface to match the background
with continuous 14 SWG annealed bare copper
wire as earth wire erected with copper earth clips to
make the pipe electrically continuous in an
approved manner ..
a) 20mm dia… R.M 17.00 17.00 15.00
b) 25mm dia.. R.M 19.00 19.00 18.00
c) 32mm dia… R.M 22.00 22.00 21.00
Note -
1) Concealing of conduit pipe shall not be carried
out on partition or 155 mm thick wall
2) No concealed wiring work shall be carried out
without explicit permission from concern S. E.
3) The depth of groove in BM work shall be equal to
outer dia meter of conduit & 20mm thick plaster
shall form a cover. For example in case of 20mm
dia conduit, the groove depth in BM shall be 20mm
& in plaster 20mm forming total groove depth
40mm from the surface of wall.
Elec/D/7 Supplying and erecting electrical switch with
embossing / stickers for purpose identification work
on provided board.
a) 6 Amp. Plain / bell push No. 18.00 18.00 17.00
b) 15 Amp. Plain No. 50.00 50.00 46.00
c) 6A,p. socket 3 pin No. 21.00 21.00 20.00
d) 15 Amp. 3 pin socket No. 46.00 46.00 44.00
e) 6 & 16Amp. 6 pin No. 110.00 110.00 105.00
f) Ceiling rose / batten holder/ slanting holder No. 18.00 18.00 17.00
Elec/D/8 Supplying and erecting switch board on wall with
required material.
a) TW pasted with sunmica (single) Sq.m. 770.00 770.00 732.00
b) TW pasted with sunmica (folding) Sq.m. 1045.00 1045.00 996.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
c) PVC board Sq.m. 815.00 815.00 780.00
Elec/D/9 Supplying and erecting compact fluo lamp 250 V.
[similar to Philips make cat no PLS 10]
a) Upto 5 W No 100.00 100.00 100.00
b) 7/9 W No 100.00 100.00 100.00
c) 10 W No. 100.00 100.00 100.00
d) 11 W No. 100.00 100.00 100.00
e) 18 W No. 200.00 200.00 200.00
Elec/D/10 Supplying and erecting compact fluorescent lamp
250 V integral type complete with ceramic mounted
by adapter.
a) 7 W No. 145.00 145.00 145.00
b) 11W No. 150.00 150.00 145.00
c) 15W No. 155.00 155.00 155.00
d) 18/20W No. 205.00 205.00 205.00
Elec/D/11 Supplying and erecting igniter for 250 volts HPSV
lamps 70/150/250/400 watts
No. 180.00 180.00 180.00
Elec/D/12 Supplying and erecting polyester compound heavy-
duty copper wound ballast 250 V for HPSV lamps.
a) 70W No. 500.00 500.00 500.00
b) 150W No. 880.00 880.00 880.00
c) 250W No. 1200.00 1200.00 1200.00
d) 400 W No. 1650.00 1650.00 1650.00
Elec/D/13 a) Supplying and erecting 250 V approved make
low watt loss polyester compound heavy-duty
copper wound choke for 18/20/36/40 W fluorescent
tubes.
No. 175.00 175.00 175.00
b) Supplying and erecting electronic ballast of
approved make having operating range 100 to 300
volts with surge suppression not less than 9 kV and
with RF filter confirming to IS 13021 ( Part-I)
suitable for 1 x 40 watt flou. Tube fitting.
No. 385.00 385.00 365.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/D/14 Supplying 18/20/36/40 watts tube starter 250 volts No. 8.00 8.00 8.00
Elec/D/15 Supplying and erecting bulk head fitting with fine
finished cast aluminum enamel painted body with
20 mm conduit entry and clear glass/prismatic glass
with guard and complete water tight hinged with
locking screw, suitable porcelain holder to house
metal filament lamp upto 100 watt erected in
position on polished double T.W. block/or 20 mm
dia H .G. conduit 30 cm in length suitable grouted in
wall.
a) Bulk head fitting. No. 145.00 145.00 145.00
b) Delux type No. 245.00 245.00 245.00
Elec/D/16 Supplying and erecting call bell with double coil
suitable for erected on polished TW block.
a) Backelite No. 45.00 45.00 42.00
b) Dingdong No. 77.00 77.00 72.00
c) Luminous No. 145.00 145.00 135.00
Elec/D/17 Supplying & erecting energy saving E+(1-4ft) 28W
stand along/retrofit tube fitting with 28W tube
complete with E.G.P. wings reflector & electronic
inbuilt circuit ballast, 130 to 325 V. A. C. complete in
an approved manner.
No. 935.00 935.00 935.00
Elec/D/18 Supplying & erecting make 1 x 28 watt T-5 Energy
efficient fluorescent tube light fitting (EETLF) Box
type complete with electronic ballat and lamp
holders duly wired ready to use for 230 volts, 50 Hz,
single phase AC supply to IS : 10322 as per quality
requirements and erected on varnished TW blocks
with flexible wire twin core 24/0,2 mm and with T-5
energy efficient tubular fluorescent lamp and
marking Sr. No. and date of erection.
No. 1000.00 1000.00 1000.00
Elec/D/19 Supplying and erecting ceiling fan with double ball
bearing and with condenser AC 230, V 50 cycles
complete erected in position with necessary flexible
copper leads of required color and with regulator,
canopy and down rod upto 300 mm in length in
provided hook/clamp with necessary rubber
bushing, clamps nuts and bolts etc and marking Sr.
No. and date of erection.
a)1200 mm sweep No 1320.00 1320.00 1320.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/D/20 Supplying and erecting electronic step type dimmer
/ speed controller complete erected on provided
switch board…
a) 300/450W No. 140.00 140.00 140.00
b) 600W No. 165.00 165.00 165.00
Elec/D/21 Supplying and erecting Exhaust fan heavy duty 230
V, AC 50 cycles with condenser complete erected in
position with necessary material. Fan motor with
moisture proof treatment and ‘E’ class insulation
and marking Sr. No and date of erection.
a) 200mm 1400 RPM No. 1100.00 1100.00 1100.00
b) 225mm 1400 RPM No. 1200.00 1200.00 1200.00
Elec/D/22 Supplying and erecting Electronic static digital
energy meter 230 volts 50 cycles AC 5./10/20/40
Amps class I ISI marked with stepper motor counter
and metal/polycarbonate enclosure with meter with
LCD display complete erected on polished TW
board duly wired with required size of weather proof
PVC wires duly tested for class II accuracy.
No. 1750.00 1750.00 1750.00
Elec/D/23 Supplying and erecting Electronic Static digital
energy meter 440- volts 50 cycles AC 3 phase
4wire 10/20/30/40/50/60 Amps class I ISI marked
with stteper motor counter and metal /polycarbonate
enclosure with metal with LCD display complete
erected on polished TW board duly wired with
required size of weather proof PVC wires duly
tested for class II accuracy.
No. 2530.00 2530.00 2530.00
Elec/D/24 Supplying and erecting Anchor type D.P. switch
heavy-duty surface type/flush type 32 A. 250 V. with
indicator lamp erected on double T.W block
covered with sun mica.
No. 145.00 130.00 130.00
Elec/D/25 Supplying and erecting metal clad 18 gauge CRCA
sheet distribution board approved make 250V
having kit-kat pattern HC type porcelain fuse
bridges 16 A per way an neutral bar connector
complete erected on iron frame/ TW plank or board.
a) 2 way No 275.00 250.00 250.00
b) 3 way No 300.00 275.00 275.00
c) 4 way No 330.00 300.00 300.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
d) 6 way No. 500.00 440.00 440.00
e) 8 way No. 550.00 500.00 500.00
Elec/D/26 Supplying and erecting metal clad 18 gauge CRCA
sheet steel distribution board approved make
415/500 V. 3 way having kit-kat pattern HC type
porcelain fuse bridges 16 A. per way and neutral
bar connector complete erected on iron frame/TW
plank or Board.
a) 16 A 3way No. 1270.00 1160.00 1160.00
b) 16 A 4way No. 1550.00 1430.00 1430.00
c) 16A 6way No. 1800.00 1650.00 1650.00
d) 16A 8way No. 2400.00 2300.00 2300.00
e) 32A 3 way No. 1700.00 1600.00 1600.00
f) 32A 4 way No. 1800.00 1720.00 1720.00
g) 32A 6 way No. 2550.00 2400.00 2400.00
h) 32A 8 way No. 3200.00 3050.00 3050.00
Elec/D/27 Supplying and erecting and marking miniature
circuit breaker conforming to IS 8828 of 1996,
single pole 0.5 Amp to 5 Amp with required wiring
connections and lugs etc in provided distribution
board.
a) Single pole 0.5A to 5 A No. 200.00 200.00 200.00
b) Single pole 6A to 32 A No. 150.00 150.00 150.00
c) Single pole 40A to 63 A No. 275.00 275.00 275.00
d) double pole 6A to 32A No. 460.00 400.00 400.00
e) double pole 40A to 63A No. 700.00 580.00 580.00
f) Triple pole 6A to 32A No. 700.00 600.00 600.00
g) Triple pole 40A to 63A No. 970.00 870.00 870.00
h) Four pole 6 A to 32A No. 940.00 825.00 825.00
I) Four pole 40A to 63A No. 1320.00 1160.00 1160.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/D/28 Supplying and erecting PVC unarmoured cable
1100 V grade with ISI mark stranded/solid
aluminium conductor complete erected on 12 mm ,
thick TW batten duly varnished/ painted and with 32
SWG 8 mm aluminium link clips and brass nails on
wall/ ceiling RCC slab with continuous 12 SWG GI
earth wire in an approved manner.
a) 2 core x 2.5 sq.mm. RM 44.00 42.00 42.00
b) 2 core x 4 sq.mm. RM 55.00 53.00 53.00
c) 2 core x 6 sq.mm. R.M 66.00 64.00 64.00
d) 2 core x 10 sq.mm. R.M 75.00 70.00 70.00
Elec/D/29 Supplying and erecting PVC unarmoured cable
1100 V grade with ISI mark stranded/solid copper
conductor complete erected on 12 mm , thick TW
batten duly varnished/ painted and with 32 SWG 8
mm aluminium link clips and brass nails on wall/
ceiling RCC slab with continuous 12 SWG GI earth
wire in an approved manner.
a)2 core x 2.5 sq.mm. R.M 75.00 70.00 70.00
b) 2 core x 4 sq.mm. R.M 100.00 95.00 95.00
c) 2 core x 6 sq.mm. R.M 150.00 140.00 140.00
d) 2 core x 10 sq.mm. R.M 240.00 230.00 230.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/E/1/ A Removing the sludge from the jackwell and
disposing upto a lead of 100 mtr.
a) For lift upto 5 m height. Cum 198.00 198.00 186.00
b) For lift above 5m and upto 10 m height. Cum 228.00 228.00 216.00
c) For lift above 10 m &upto 15 m height. Cum 264.00 264.00 252.00
d) For lift above 15 m height. Cum 300.00 300.00 288.00
Elect/E/1/B Removing the sludge from the CLF/ Sump and
disposing upto a lead of 100 mtr.
Cum 120.00 120.00 114.00
Elec/E/2 Painting of electrical, mechanical machinery such
as pump sets, panels, motors, compressors, surge
arrestors, transformers, HT and LT breakers,
including rubbing down oil paint, cleaning with
emery papers and making the surface clean to
receive the paints and providing and applying one
coat of primer and two coats of synthetic super
enamel painting conforming to IS of approved
colour and shade, including scaffolding, if
necessary.
Sqm 90.00 90.00 85.00
Elec/E/3 Oil filtering of the transformer including testing of oil
samples, submitting test results before and after
filtering, to and fro transportation, sludge removal
etc complete at each location.
a) IF the total quantity is less than Liter 12.00 12.00 12.00
200 litre at each location
b) IF the total quantity is less than
500 litre at each location Liter 10.00 9.00 9.00
c) IF the total quantity is less than
1500 litre at each location Liter 8.00 9.00 9.00
.
d) IF the total quantity is more than
1500 litre at each location Liter 7.00 8.00 8.00
Elec/E/4 Supply of filtered transformer oil with test certificate Liter 150.00 150.00 150.00
Elec/E/5 Providing and supplying at departmental store Plain
PVC pipes(Working pressure 6 kg/cm2) as per
latest BS/IS specifications including cost of
transportation and bearing ISI mark.
a) 25mm dia R.M 19.00 19.00 18.00
b) 40mm dia R.M 35.00 35.00 33.00
Electrical-E-Miscellaneous Items.
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
c) 50mm dia R.M 50.00 50.00 47.00
d) 63mm dia R.M 80.00 80.00 75.00
e) 75mm dia R.M 115.00 115.00 110.00
f) 100mm dia R.M 200.00 200.00 190.00
Elec/E/6 Providing and supplying PVC 90 degree
bend(Working pressure 6 kg/cm2) including cost of
transportation of specials at departmental store etc
as per BS/IS specifications bearing ISI mark.
a) 25mm dia No. 37.00 37.00 35.00
b) 40mm dia No. 45.00 45.00 42.00
c) 50mm dia No. 53.00 53.00 50.00
d) 63mm dia No. 60.00 60.00 57.00
e) 75mm dia No. 75.00 75.00 70.00
f) 100mm dia No. 90.00 90.00 85.00
Elec/E/7 Providing and supplying PVC flanges(Working
pressure 6 kg/cm2) at departmental store including
cost of transportation and testing etc as per latest
BS/IS specification bearing IS mark.
a) 25mm dia No. 76.00 76.00 72.00
b) 40mm dia No. 87.00 87.00 82.00
c) 50mm dia No. 109.00 109.00 102.00
d) 63mm dia No. 127.00 127.00 120.00
e) 75mm dia No. 152.00 152.00 144.00
f) 100mm dia No. 176.00 176.00 167.00
Elec/E/8 Providing and supplying departmental store PVC
Tee (Working pressure 6 kg/cm2)including cost of
transportation etc as per latest BS/IS specifications
bearing IS mark.
a) 25mm dia No. 60.00 60.00 57.00
b) 40mm dia No. 69.00 69.00 65.00
c) 50mm dia No. 93.00 93.00 88.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
d) 63mm dia No. 104.00 104.00 98.00
e) 75mm dia No. 112.00 112.00 105.00
f) 100mm dia No. 127.00 127.00 120.00
Elec/E/9 Providing and supplying departmental store PVC
valve (Working pressure 6 kg/cm2) including cost of
transportation etc as per latest BS/IS specifications
bearing IS mark.
a) 25mm dia No. 656.00 656.00 625.00
b) 40mm dia No. 725.00 725.00 690.00
c) 50mm dia No. 790.00 790.00 750.00
d) 63mm dia No. 968.00 968.00 920.00
e) 75mm dia No. 1040.00 1040.00 990.00
f) 100mm dia No. 1282.00 1282.00 1220.00
Elec/E/10 Providing and supplying departmental store PVC
socket.(Working pressure 6 kg/cm2) Adopter
including cost of transportation etc as per latest
BS/IS specifications bearing IS mark.
a) 25mm dia No. 39.00 39.00 37.00
b) 40mm dia No. 46.00 46.00 43.00
c) 50mm dia No. 60.00 60.00 57.00
d) 63mm dia No. 71.00 71.00 67.00
e) 75mm dia No. 82.00 82.00 78.00
f) 100mm dia No. 98.00 98.00 93.00
Elec/E/11 Providing and applying Apcolite paint and painting
of letters of given size as per requirement on MS
name boards including red oxide paint on back side
of board.
Sqm 363.00 363.00 345.40
Elec/E12 Providing and applying Apcolite paint and painting
of letters of given size as per requirement on Civil
structures.
Sqm 220.00 220.00 209.00
Elec/E13 Providing and fixing copper lightening arrestor
including copper rod, upper terminal with spike,
tape conductor, copper earth plate excavating,
laying the conductor with clamps and refilling the pit
with salt and coal powder etc complete.
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
a) Copper strip of 20mm x 3mm (including required
scaffolding)
Kg 605.00 605.00 605.00
b) GI strip of 25mm x 3mm (including required
scaffolding)
Kg 247.50 247.50 220.00
c) Copper rod with spike with required clamp &
foundation
No 2090.00 2090.00 2013.00
d) Copper plate earthing having plate size 450mmx
450mmx 5mm with required salt & coal powder
including excavation & refilling.
No 4070.00 4070.00 3850.00
Elec/E14 Supplying & erecting bank of all polypropylene
(APP type) condensers with the standard
capacities of 1,2,3,5,7, 10,12.5 & 15 KVAR units of
PF correction for operation on 3 phase 50 cycles
400/440V (+10%) with externally discharging
resistances, earthing terminals & built on angle iron
or channel iron frame work & provided with
terminal cover box complete erected on provided
iron bracket or on floor duly tested by licensee.
(Make Probodhan, Univarsal, Madhav, Shrim,
Epcos.)
per
KVAR
592.00 592.00 592.00
Elec/E/15 Supplying & erecting bank of mixdielectric
condensers with the standard capacities of
1,2,3,5,7, 10,12.5 & 15 KVAR units of PF correction
for operation on 3 phase 50 cycles 400/440V
(+10%) with externally discharging resistances,
earthing terminals & built on angle iron or channel
iron frame work & provided with terminal cover box
complete erected on provided iron bracket or on
floor duly tested by licensee.
per
KVAR
700.00 700.00 700.00
Elec/E/16 Fabrication of spares for the pumping
machinery suitable to match with the existing
fitments & as per actual site conditions
including cost of material, salvage, machining,
labour, taxes & duties, incidentals, overheads,
packing & forwarding etc. complete as per
designation given below.
A) Housing or Casing
1) Mild Steel Kg. 300.00 300.00 300.00
2) Cast Steel Kg. 322.50 322.50 322.50
3) Cast Iron Kg. 352.50 352.50 352.50
B) Axle or Shaft
1) Mild Steel Kg. 255.00 255.00 255.00
2) EN-8 Kg. 277.50 277.50 277.50
3) Stainless Steel -304 or 410 Kg. 555.00 555.00 555.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
4) Stainless Steel -316 Kg. 735.00 735.00 735.00
C) Threaded Sleeve
1) Mild Steel Kg. 270.00 270.00 270.00
2) EN-8 Kg. 300.00 300.00 300.00
3) Stainless Steel -304 or 410 Kg. 570.00 570.00 570.00
4) Stainless Steel -316 Kg. 750.00 750.00 750.00
D) Plain/ Collared Bush
1) Mild Steel Kg. 232.50 232.50 232.50
2) Cast Iron / EN-8 Kg. 262.50 262.50 262.50
3) Stainless Steel -304 or 410 Kg. 525.00 525.00 525.00
4) Stainless Steel -316 Kg. 705.00 705.00 705.00
5) Gun Metal Kg. 877.50 877.50 877.50
6) Neoprene rubber Kg. 525.00 525.00 525.00
E) Check / Lock Nut
1) Mild Steel Kg. 262.50 262.50 262.50
2) EN-8 Kg. 292.50 292.50 292.50
3) Stainless Steel -304 or 410 Kg. 562.50 562.50 562.50
4) Stainless Steel -316 Kg. 742.50 742.50 742.50
F) Wearing / Seat Ring
1) Mild Steel Kg. 502.50 502.50 502.50
2) EN-8 Kg. 540.00 540.00 540.00
3) Stainless Steel -304 or 410 Kg. 843.00 843.00 843.00
4) Stainless Steel -316 Kg. 1042.50 1042.50 1042.50
5) Gun Metal Kg. 1200.00 1200.00 1200.00
G) Threaded Coupling
1) EN-8 Kg. 300.00 300.00 300.00
2) Stainless Steel -304 or 410 Kg. 570.00 570.00 570.00
3) Stainless Steel -316 Kg. 750.00 750.00 750.00
Elec/E/17 Fabrication of spindle for sluice valve of any
size including cost of material & labour with
necessary machining such as cutting, facing,
threading, match with existing couter part &
facilitate for interchangeability.
a) EN-8 Kg. 320.00 320.00 320.00
b) Stainless Steel -304 or 410 Kg. 510.00 510.00 510.00
c) Stainless Steel -316 Kg. 660.00 660.00 660.00
d) Gun Metal Kg. 850.00 850.00 850.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/E/18 Dismantling & overhauling of Vertical Turbine
pumps from the position having 10 mtrs.
suspended length (from Bell Mount to Discharge
Head.), cleaning, checking, aligning, assembling
i.e., refitting, commissioning with trial run on no
load & full load for at least 30 minutes including
replacement of spare parts, fastners (which
shall be made available by MIDC at free of cost
at site of work) etc. complete as per site
requirements.
a) 10 H.P. to 50 H. H.P. 100.00 100.00 100.00
b) above 50 H.P. to 120 H.P. H.P. 90.00 90.00 90.00
c) above 120 H.P. to 225 H.P. H.P. 80.00 80.00 80.00
d) above 225 H.P. to 500 H.P. H.P. 70.00 70.00 70.00
e) aboe 500 H.P. to 800 H.P. H.P. 60.00 60.00 60.00
Note : For ± suspended length, vary the above
unit rate per metre at ±5% according.
Elec/E/19 Monthly inspection & servicing of D.G. set with
panel covering replacement of damaged/ worn
out misc. spare parts, oil seals, packings, oil &
fuel filters, engine tune up, with apprpriate
alingment, cleaning of radiators, colling fins etc.
complete with due commissioning & trial run
with at least 30 minutes on full load (spares &
consumables shall be provided by MIDC at free
of cost at site of work.
a) from 10 KVA to 30 KVA KVA 17.50 17.50 17.50
b) above 30 KVA to 75 KVA KVA 15.00 15.00 15.00
c) above 75 KVA to 200 KVA KVA 12.50 12.50 12.50
d) above 200 KVA to 320 KVA KVA 9.00 9.00 9.00
e) above 320 KVA to 500 KVA KVA 7.50 7.50 7.50
Elect/E/20 Monthly inspection & servicing of split/ window
type air conditioning unit including operations
of remote control set, cleaning of air filters ,
checking of copper tubing, checking of gas
pressure and refilling of gas as per requirement
and replacement of minor worn out parts .
a) 1.0 T capacity 400.00 400.00 400.00
b) 1.5 T capacity 500.00 500.00 500.00
c) 2.0 T capacity 600.00 600.00 600.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/F/1 Supplying and erecting steel tubular swaged pole
as per IS-2713 part-II complete erected in C.C.
foundation duly painted with two coats of red oxide
paint and one coat of bituminous paint for the length
to be embedded in ground and plinth and erected in
position with CI/MS base plate of 30 x 30 x 0.6 cm
thick at the bottom welded, complete..(C.C. and
excavation shall be paid separately under relevant
items.)
a)Pole 139.7 x114.3x 88.9 mm dia with 4.5 x 4.5 x
3.25mm thickness, (5 + 2 + 2 mtr) length
respectively total 11 mtr long ( wt-113 kg)
No. 9500.00 9400.00 9300.00
9544.46
b)Pole 139.7 x114.3x 88.9 mm dia with 4.5 x 4.5 x
3.25mm thickness, ( 5.60 + 2.7 + 2.7 mtr) length
respectively total 11 mtr long ( wt-140 kg)
No. 11825.00 11500.00 11500.00
c)GI pipe pole B Class 75/80mm dia without
painting.
R.M 825.00 785.00 785.00
d)MS pipe pole B Class 75/80mm dia with two
coats of red oxide.
R.M 715.00 670.00 670.00
Elec/F/2 Supplying and erecting streetlight bracket on the
top of the pole with 15 cm welded corner support of
suitable size of MS sheet 3 mm thick complete with
6 mm dia set screw duly painted with one coat of
red oxide paint complete erected.
a) Made from 25mm dia B class GI pipe 1.2 mtr in
length welded to the pole cap 4mm thick 30 cm in
length.
No 360.00 330.00 330.00
b) Made from 40mm dia ‘B’ class GI pipe 1. 2 mtr in
length welded to pole cap 4 mm thick 30 cm in
length.
No 415.00 385.00 385.00
c) Made from 40mm dia ‘B’ class GI pipe 2.00 mtr
length welded to pole cap size 100 mm dia and 30
cm long for single fitting.
No 605.00 560.00 550.00
d) Made from 40mm dia ‘B’ class GI pipe 2.00 mtr
length welded to pole cap size 100 mm dia and 30
cm long for double fitting.
No 1155.00 1100.00 1045.00
Electrical-F-Street Light Items.
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/F/3 Supplying and erecting streetlight brackets for
erection side entry w.p. fitting/ MV fitting/ SV fitting
of any capacity erected on pole with ‘B” Class GI
pipes of required length erected with 2 nos of 40 x 5
mm MS flat clamps and with suitable nut and bolts
etc duly painted with two coats of red oxide and 2
coats of aluminum paint.
a) 25mm dia GI pipe… R.M 240.00 220.00 220.00
b) 40mm dia GI pipe.. R.M 310.00 275.00 275.00
Elec/F/4 Supplying and erecting streetlight HPSV lamp fitting
having deep drawn one piece aluminum body nickel
chrome plate reflector with clear glass and
electronics Igniter etc with necessary wiring
complete with accessories such as copper wound
choke, condenser etc ( Excluding lamp).
a) 70 watt HPSV… No. 2000.00 2000.00 2000.00
b) Suitable for 70 watt HPSV with built in energy
saving dynamic power saving device. (DPSD)
No. 3000.00 3000.00 3000.00
c)Suitable for 150 watt HPSV… No. 3600.00 3600.00 3600.00
d) Suitable for 150 watt HPSV with built in energy
saving dynamic power saving device. (DPSD)
No. 4600.00 4600.00 4600.00
Elec/F/5 Supplying fluorescent tube light.
a) 600mm 20/ 18 Wt. No. 50.00 50.00 50.00
b) 1200mm 40W / 36W No. 55.00 55.00 55.00
Elec/F/6 Supplying and erecting HPSV lamp 3 pin
BC/scrwed cap head type 250 volts.
a) 70W No. 350.00 350.00 350.00
b) 150W No. 475.00 475.00 475.00
c) 250W No. 525.00 525.00 525.00
Elec/F/7 Supplying and erecting blended lamp 250 volts 160
watt.
No. 275.00 275.00 275.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/F/8 Supplying and erecting FRP box permanent gray
color with 15 Amp 250 volts porcelain base kit Kat
fuse and top with bakelite connector strip 4 way
having locking arrangement with lock and key with
arrangements for incoming and out going cables of
the bottom of the box and out going wire leads at
the rear side with necessary fixing arrangements for
the erection on the poles with suitable size clamps
provided with nuts, bolts and washers etc complete
with work MIDC embossed.
a) 300mm x 200mm x 125mm, 2.7mm thick No. 435.00 435.00 435.00
b) 250mm x 200mm x 100mm, 2.7mm thick No. 320.00 320.00 320.00
c) 150mm x 125mm x 100mm, 2.7mm thick No. 285.00 285.00 285.00
Elec/F/9 Supplying and erecting ISI mark GI pipe A class
erected for enclosing PVC armored cable on wall or
pole with clamps and upper end closed with TW
bush and sealed with compound
a) 25mm dia R.M 185.00 185.00 185.00
b) 40mm dia R.M 235.00 235.00 235.00
c) 50mm dia R.M 320.00 295.00 295.00
d) 80mm dia R.M 495.00 465.00 465.00
Elec/F/10 Supplying and erecting PVC armored cable 1100 V
grade with ISI mark stranded / solid aluminum with
continues 12 SWG GI earth wire complete erected
on wall with saddles and spaces, erected on pole
with clamps or in provided trench in an approved
manner.
a) 2 core x 2.5 sq.mm R.M 65.00 65.00 65.00
b) 2 core x 4 sq.mm R.M 70.00 70.00 70.00
c) 2 core x 6 sq.mm R.M 85.00 85.00 85.00
d) 2 core x 10 sq.mm R.M 100.00 100.00 100.00
e) 4 core x 4 sq.mm R.M 100.00 100.00 100.00
f) 4 core x 6 sq.mm R.M 110.00 100.00 100.00
g) 4 core x 10 sq.mm R.M 120.00 110.00 110.00
h) 4 core x 16 sq.mm R.M 155.00 140.00 140.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
i) 3.5/4 core x 25 sq.mm R.M 160.00 160.00 160.00
j) 3.5 core x 35 sq.mm R.M 200.00 200.00 200.00
k) 3.5 core x 50 sq.mm R.M 270.00 270.00 270.00
l) 3.5 core x 70 sq.mm R.M 355.00 325.00 325.00
m) 3.5 core x 95 sq.mm R.M 500.00 450.00 450.00
n) 3.5 core x 120 sq.mm R.M 600.00 600.00 600.00
o) 3.5 core x 150 sq.mm R.M 720.00 720.00 720.00
p) 3.5 core x 185 sq.mm R.M 750.00 750.00 750.00
q) 3.5 core x 240 sq.mm R.M 1100.00 1100.00 1100.00
r) 3.5 core x 300 sq.mm R.M 1420.00 1420.00 1420.00
s) 3.5 core x 400 sq.mm R.M 1650.00 1500.00 1500.00
Elec/F/11 Supplying and erecting heavy duty flange type
brass cable glands with brass washers rubber rings
complete erected with cable ends and leads
connected.
a) For 2 to 4 core 2.5 sq.mm. / 2 to 4 core 4.5
sq.mm. / 2 core 6 sq.mm. PVC armoured cable
No. 17.00 17.00 17.00
b) For 3 to 4core 6sq.mm. /2 to 4core 10sq.mm. No. 28.00 28.00 28.00
c) For 4 core 16 sq.mm. & 25 sq.mm. No. 50.00 50.00 50.00
d) 3.5/4 core x 35 sq.mm No. 66.00 66.00 66.00
e) 3.5/4 core x 50 sq.mm No. 83.00 84.00 85.00
f) 3.5/4 core x 70 sq.mm No. 88.00 88.00 88.00
g) 3.5/4 core x 95 sq.mm No. 99.00 99.00 99.00
h) 3.5/4 core x 120 sq.mm No. 110.00 110.00 110.00
i) 3.5/4 core x 150 sq.mm No. 121.00 121.00 121.00
j) 3.5/4 core x 185 sq.mm No. 160.00 160.00 160.00
k) 3.5/4 core x 240 sq.mm No. 182.00 182.00 182.00
l) 3.5/4 core x 300 sq.mm No. 220.00 198.00 198.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
m) 3.5/4 core x 400 sq.mm No. 300.00 275.00 275.00
Elec/F/12 Supplying and erecting crimping type alluminium
lugs confirming to IS : suitable for cable evenly
crimped with high pressure tool & connected to
switch gear with brass / cadmium plated nut bolts in
an approved manner.
a) upto 16 sq.mm. No. 4.00 4.00 4.00
b) For 25 sq.mm. No. 5.00 5.00 5.00
c) For 35 sq.mm. No. 7.00 7.00 7.00
d) For 50 sq.mm. No. 9.00 9.00 9.00
e) For 70 sq.mm. No. 10.00 10.00 10.00
f) For 95 sq.mm. No. 12.00 12.00 12.00
g) For 120 sq.mm. No. 16.00 16.00 16.00
h) For 150 sq.mm. No. 22.00 22.00 22.00
I)For 185 sq.mm. No. 28.00 28.00 28.00
j) For 225 sq.mm. No. 38.00 38.00 38.00
k) For 240 sq.mm. No. 40.00 40.00 40.00
l) For 300 sq.mm. No. 60.00 60.00 60.00
m)For 400 sq.mm. No. 77.00 77.00 77.00
Elec/F/13 Supplying and erecting pipe type earthing with
40mm dia 2.5 mtr. long GI pipe or 20mm dia GI rod
burried in earth with necessary double GI earth wire
no. 8 SWG complete erected & connected to
nearest switch gear / earth terminal.
No 630.00 630.00 600.00
Elec/F/14 Providing cement concrete for foundation or for
concrete filling in M-10 CC duly plastered with
necessary curing for pole foundation/ muffing.
Cum 2400.00 2400.00 2400.00
Elec/F/15 Making trench of 0.97 mtr deep including Providing
and laying screened sand bed of 20 cm thick and
bricks placed on the top of the cable width wise all
over the run and backfilling the excavated earth
without stone or hard material and making the
surface proper.
R.M 100.00 100.00 100.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elect/F/16
(A)
Making trench in soft soil in suitable width for laying
HT XLPE cable of 22 KV upto 400 Sq.mm with red
bricks, sand bedding & RCC half round covering
pipes etc. all over the run and back filling the
excavated earth without stones or hard material and
making the surface proper with 20 cm crown on the
top (Size of trench 1 mtr x 0.50 Mtr)
R.M 360.00 360.00 330.00
Elec/F/17 Providing, supplying and erecting feeder pillar
fabricated out of 18 SWG GI sheet including cutting,
bending, drilling, welding, riveting etc and painting
with one coat of red oxide paint and two coats of
enamel paint.
Sqm 1000.00 900.00 900.00
Elec/F/18 Supplying and erecting hylem sheet/ ebonite
sheet…
a) 3mm thick Sqm 415.00 415.00 395.00
b) 6 mm thick Sqm 770.00 770.00 730.00
Elec/F/19 Supplying and erecting MS angle frame work for
erection of panel board or other purpose with
bending, cutting, drilling and welding complete with
one coat of red oxide and two coats enamel paint.
Kg 75.00 75.00 75.00
Elec/F/20 Supplying and erecting self-locking arrangement
with keys, made of brass duly erected, flush with
surface of panel board.
No 125.00 125.00 118.00
Elec/F/21 Supplying and erecting iron clad/metal clad switch
with fuse and neutral link conduit entry erected on
angle iron frame.
a) 240/ 250V 16A. No. 310.00 310.00 310.00
b) 240/ 250V 32A. No. 530.00 530.00 530.00
c) 240/ 250V 63A. No. 1480.00 1480.00 1480.00
d) 415/ 500V 16A. No. 660.00 660.00 660.00
e) 415/ 500V 32A. No. 900.00 900.00 900.00
f) 415/ 500V 63A. No. 2000.00 2000.00 2000.00
g) 415/ 500V 100A. No. 4700.00 4700.00 4700.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/F/22A Supplying and erecting Quartz Electronic time
switch 24 hours dial to work on 250 volt 50 cycle AC
having built in rechargeable nickel cadmium
batteries to run the time switch on failure of supply
having switch contact rating upto 16 A to use
independently or in conjunction with contactor .
No. 2500.00 2500.00 2100.00
Elec/F/22B Supplying and erecting programmable digital
almanac timer microcontroller based with real time
clear to operate on derived switch "ON" and switch
"OF" street light as per daily sunset and sunrise
respectively automatically having four digit LED
continuous time display relay O/P 230V/ 10Amp
with 10 year battery backup & manual over drive
facility capable to drive different capacity contactors
timer erected in M.S. box in an approved manner.
No. 4060.00 4060.00 4060.00
Elec/F/23 Supplying and erecting power contactor for time
switch complete erected with necessary material.
a) 250 V 16 A No. 950.00 950.00 950.00
b) 250V 32A No. 2100.00 2100.00 2100.00
c) 440V 16 A No. 1000.00 1000.00 1000.00
d) 440V 40A No. 3200.00 3200.00 3200.00
e) 440 V 70 A No 4500.00 4500.00 4500.00
Elec/F/24 Providing and erecting 6 mtr. Height galvanised
(BSEN, ISO 1461) Octogonal pole with bottom of
130 mm, A/F top 70 mm A/F on provided foundation
as per PWD's Specification No. OH-PL/PSC.
No 8500.00 8500.00 8500.00
Elect/F/25 Providing and erecting 7 mtr. Height galvanised
(BSEN, ISO 1461) Octogonal pole with bottom of
130 mm, A/F top 70 mm A/F on provided foundation
as per PWD's Specification No. OH-PL/PSC.
No 9500.00 9500.00 9500.00
Elect/F/26 Providing and erecting 8 mtr. Height galvanised
(BSEN, ISO 1461) Octogonal pole with bottom of
135 mm, A/F top 70 mm A/F on provided foundation
as per PWD's Specification No. OH-PL/PSC.
No 11400.00 11400.00 11400.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elect/F/27 Providing and erecting 9 mtr. Height galvanised
(BSEN, ISO 1461) Octogonal pole with bottom of
155 mm, A/F top 70 mm A/F on provided foundation
as per PWD's Specification No. OH-PL/PSC.
No 13500.00 13500.00 13500.00
Elect./F/28 Supplying and erecting streetlight energy efficient T-
5 streetlight fittings suitable for 4x14 W T-5 lamps
with power factor > 0.95. The fitting canopy is
made of deep drown CRCA, MS sheet powder
coated in colour provided with serrated acrylic
diffuser and gasket including lamps.
No 3500.00 3500.00 3500.00
Elect/F/29 Supplying and erecting streetlight energy efficient T-
5 streetlight fittings suitable for 2x24W T-5 lamps
with power factor > 0.95. The fitting canopy is
made of deep drown CRCA, MS sheet powder
coated in colour provided with serrated acrylic
diffuser and gasket including lamps.
No. 2200.00 2200.00 2200.00
Elect/F/30 Supplying and erecting streetlight energy efficient T-
5 streetlight fittings suitable for 4x24W T-5 lamps
with power factor > 0.95. The fitting canopy is
made of deep drown CRCA, MS sheet powder
coated in colour provided with serrated acrylic
diffuser and gasket including lamps.
No. 4500.00 4500.00 4500.00
Elect/F/31 Designing and casting M-20 R.C.C. foundation
suitable octoganal pole considering the safe soil
bearing capacity at site 10T/Sq.m including
excavation, foundation nuts bolts etc in an
approved manner.
a) for 8 and 9 mtr octoganal pole ( Size 0.6 x 0.6 x
2.0 )
No. 7250.00 7000.00 7000.00
b) for 6 and 7 mtr octoganal pole ( Size 0.6 x 0.6 x
1.5 )
No. 5750.00 5500.00 5500.00
Elect/F/32 Maintence of street lights including Highmast
including providing licensed Electrician wireman &
labours for day to day checking, identifing &
rectifying the the faults in street light system,
replacing of burnt accessories of street light
fixtures, FRP box, cable wires pipes etc.as directed
by Engineer-in charge( Materials such as
lamp,chock,ignitors,wires,FRP box pipes etc.will be
supplied by MIDC)
C) Streetlights upto 1500 Nos Per
month/
pole
60.00 50.00 50.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
d) Streetlights above 1500 Nos Per
month/
pole
50.00 45.00 45.00
Elect/F/33 Supplying and erecting T-5 14 W Energy Efficient
fluoroscent tube on existing fitting.
No. 110.00 110.00 110.00
Elect/F/34 Supplying and erecting T-5 24 W Energy Efficient
fluoroscent tube on existing fitting.
No. 160.00 160.00 160.00
Eect/F/35 Supplying and erecting electronic 14 W choke. No. 250.00 250.00 250.00
Elect/F/36 Supplying and erecting electronic 24 W choke. No. 300.00 300.00 300.00
Elec/G/1 Supplying and erecting approved make 3 phase, 50
c/s Oil immersed and naturally cooled, outdoor type/
indoor type copper wound transformer connected
delta on HV side and star on LV side with additional
neutral brought out on load side, rating with HV
tapping plus or minus 2.5%-5% continuously rated
for full load and temperature rise not exceeding 45°
C by the resistance of the winding after continues
run at full load rating complete with the following
standard mounting…
1) OFF load tap changing switch
2) Oil conservation with filling holes and cap and
plain oil level gauge
3) Silicagel dehydrating breather
4) Oil drain-valve .
5) Thermometer pocket.
6) Oil filter valve.
7) Lifting arrangement.
8) Two earthing terminals
9) Diagram and rating plate.
10) First filling oil with dielectric strength of 50 kV /
No break.
11) Four bi-directional plain rollers.
12) Air vent
13) Explosion vent.
Electrical-G- Sub Station
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
The terminal arrangement bushings, with
lugs/cable ends box on HV side cable end box on
LV side complete with test certificates from
manufacturers and completely erected on provided
plinth or on pole as per direction. (The transformer
shall be tested at factory in presence of
Departmental Engineer before dispatch to site).
A) 11 KV / 433 V
a) 63KVA No. 154031.00 154031.00 154031.00
b) 100KVA No. 193643.00 193643.00 193643.00
c) 160KVA No. 275369.00 275369.00 275369.00
d) 200KVA No. 313910.00 313910.00 313910.00
e) 250KVA No. 363079.00 363079.00 363079.00
f) 315KVA No. 449981.00 449981.00 449981.00
g) 400KVA No. 472792.00 472792.00 472792.00
h) 500KVA No. 609159.00 609159.00 609159.00
i) 630KVA No. 709891.00 709891.00 709891.00
B) 22KV/433V
a) 63KVA No. 169429.00 169429.00 169429.00
b) 100KVA No. 219164.00 219164.00 219164.00
c) 160KVA No. 308173.00 308173.00 308173.00
d) 200KVA No. 359449.00 359449.00 359449.00
e) 250KVA No. 412401.00 412401.00 412401.00
f) 315KVA No. 497622.00 497622.00 497622.00
g) 400KVA No. 506563.00 506563.00 506563.00
h) 500KVA No. 678308.00 678308.00 678308.00
i) 630KVA No. 747993.00 747993.00 747993.00
Elec/G/2 Supplying and erecting conductor erected for
overhead line with stringing with proper size of
aluminum binding wire and suitable size of P.G
clamps for jumpering etc complete.
A) All Alluminium….
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
a) 7/1.96mm (Rose) R.M 17.00 17.00 17.00
b) 7/2.21mm (Gnat) R.M 21.00 21.00 21.00
c) 7/2.48mm (Iris) R.M 26.00 26.00 26.00
d) 7/2.78mm (Pansy) R.M 33.00 33.00 33.00
e) 7/3.1mm (Ant) R.M 41.00 41.00 41.00
B) ASCR
a) 6/1-2.11mm (Squire)) R.M 22.00 22.00 22.00
b) 6/1-2.59mm (Weasel) R.M 31.00 31.00 31.00
c) 6/1-3.6mm (Ferrot)) R.M 42.00 42.00 42.00
d) 6/1-3.66mm (Mink) R.M 62.00 62.00 62.00
e) 6/1-4.726mm (DOG) R.M 77.00 77.00 77.00
C) 8 SWG GI wire R.M 9.50 9.50 9.50
Elec/G/3 Supplying and erecting, approved make thyrite type
lightening arresters, with necessary ancillary
material, complete erected on provided cross arm
and connected to the over-head line (similar to
Catalog No. 22A-09 of IGE make) distribution class
a) for 11 KV supply No. 2800.00 2800.00 2800.00
b) for 22 KV supply No. 5530.00 5530.00 5530.00
Elec/G/4 Supplying and erecting disc type insulator suitable
for overhead line, complete erected with suitable
hardware on provided cross arm.
a) for 11 KV No. 1290.00 1290.00 1290.00
b) for 22 KV No. 1968.00 1968.00 1968.00
Elec/G/5 Supplying and erecting pin type insulator suitable
for overhead line complete erected with suitable
hard ware on provided cross arm.
a) for 11 KV No. 318.00 318.00 318.00
b) for 22 KV No. 885.00 885.00 885.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/G/6 Supplying and erecting approved make outdoor
type gang operate air break, triple pole switch 200
amperes, capacity with 3 post pin type insulator per
phase, mounted in horizontal or vertical position on
provided cross arm with adequate length of GI pipe
for operating handle erected on extended square
shaft. The operating handle provided with lock and
key at suitable height from ground level with
necessary clamp (Kiran/Pactil make only.)
a) for 11 KV No. 16258.00 16258.00 16258.00
b) for 22 KV No. 25661.00 25661.00 25661.00
Elec/G/7 Supplying and erecting approved make, out door
drop out fuse with insulator compete with fuse
holders, fuse barrel with metal fitting, fuse element
mounted on MS channel with working current of 15
Amps capacity complete erected on provided cross
arm
a) for 11 KV No. 8703.00 8703.00 8703.00
b) for 22 KV No. 14592.00 14592.00 14592.00
Elec/G/8 Supplying and erecting strips used for earthing on
wall and /or any other purpose with necessary
clamps fixed on wall painted with bituminous paint
in an approved manner.
a) Alluminium. Kg 332.00 332.00 332.00
b) Copper Kg 617.00 617.00 617.00
c) GI Kg 99.00 99.00 99.00
Elec/G/9 Supplying and erecting wires used for earthing on
wall and /or any other purpose with necessary
clamps fixed on wall painted with bituminous paint
in an approved manner.
a) Copper Kg 602.00 602.00 602.00
b) GI Kg 99.00 99.00 99.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/G/10 Supplying and erecting galvanized cast iron plate
size 60 x 60 x 0.6 cms buried in specifically
prepared earth pit 1.5 mtr below ground with 40 kg
charcoal and salt with alternate layers of charcoal
and slat with 19m dia GI pipe with funnel with a wire
mesh for watering and brick masonry block CI cover
complete as per para 7.3 of IS 3043 with necessary
length of double GI earth wire No. 6 SWG bolted
with lug to the plate and covered in 12mm dia GI
pipe 2.5 mtr long complete to the nearest
switchgear with end socket as per directions and
duly tested by earth tester and recording the results.
No. 2214.00 2214.00 2214.00
Elec/G/11 Supplying and erecting GI stay set for poles,
including loop insulators at inaccessible height
complete with anchor plate 150 x 150 x 6mm
straining screws GI stay wire 7/8 SWG GI stay rod
20 mm x 1.8 mtr length and pole clamps duly
erected in provided cement concrete foundation.
No. 1390.00 1390.00 1390.00
Elec/G/12 Providing printed instruction chart for treating
persons suffering from electric shock, printed in
English & Marathi and duly framed with front
glasses.
No 69.00 69.00 69.00
Elec/G/13 Providing pair of duly tested rubber hand gloves
suitable for working on 22 kV supply.
Pair 435.00 435.00 435.00
Elec/G/14 Supply of fire bucket round bottom duly painted, 9
liters capacity and filled with dry sand and kept on
provided stand or wall hook.
No 402.00 402.00 402.00
Elec/G/15 Providing floor mounting stand for keeping 4 nos of
bucket 5’ in length 3’ in height made out of 30 x 30
x 4 mm angle iron welded with 4 hooks and duly
painted with one coat of red lead and two coats of
silver paint.
No 1841.00 1841.00 1841.00
Elec/G/16 Supplying and erecting wall hook 9” projection for
keeping fire buckets made out of 15mm dia MS rod
grouted in wall to a depth of minimum 15 cms.
No 49.00 49.00 49.00
Elec/G/17 Supplying standard first aid box with all the
standard contents.
No. 323.00 323.00 323.00
Elec/G/18 Supplying rubber matting and required length and
breadth with good insulation property for 11 kV.
a) 3mm thick sq.m 640.00 640.00 610.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
b) 6mm thick sq.m 1100.00 1100.00 1040.00
Elec/G/19 Supplying and erecting DCP type fire extinguisher 5
kg CAP cartridge type with GM cartridge type with
GM cap 150 gram CO2 gas cartridge power
brackets conforming to IS 2171-85 and having
complete erected with necessary clamps made
from 50 x 6 mm MS flat with nuts and bolts grouted
in wall complete.
No. 2414.00 2414.00 2414.00
Elec/G/20 Supplying and erecting ABC powder type 'Cease
Fire' type fire extinguisher as per IS : 13849 of 1
kg capacity with necessary clamp for erection
on wall.
No 1709.00 1709.00 1709.00
Elec/G/21 Supplying and erecting fencing of section having
size 2450mm in hight from ground level and
1200mm width by using angle iron size 50 x 50 x 6
mm erected in i.e. foundation 15 x 15 x 40 cms
deep. The section of frame shall be fitted with flat
iron supports of size 25 x 6 mm on top bottom and
middel and chin link jali of 3.26 mm dia/ 10 SWG GI
hard wire mesh of 50 x 50 mm to the angle iron at
every distance of 30 cm by iron slad complete duly
painted with.
No 2493.00 2493.00 2493.00
Elec/G/22 Supplying and erecting 50 x 50 x 6 mm angle iron
as corner support 0.5 mtr away from the fence
support fixed at the middle of the fencing frame and
the other side in CC foundation of 15 x 15 x 40 cms
complete duly painted with one coat of red oxide
and two coats of aluminum paint.
No 948.00 948.00 948.00
Elec/G/23 Supplying and erecting double leaf hinged door
each 150 cms in width x 185 cms in height using
25mm dia ‘B’ grade ISI market GI pipe from all four
sides with necessary bends with cross supports of
angle iron 45 x 45 x 5 mm with the door leaf
covered with chain link jali 50 x 50 mm made from
3.26 mm dia/10 SWG GI wire with necessary flat
iron covering all around with necessary number of
spikes of size 10mm dia at top and bottom at
150mm apart to match the height of fencing. The
door shall have heavy latches and side channels of
100 x50 x5 mm locking arrangement with lock of
Godrej Navtal, medium size with duplicate keys, the
fencing complete erected with anti corrosive red
oxide paint and two coats of prescribed enamel
paint/silver paint. The channel iron of size 100 x 50
mm x 2.5 mtrs length shall be provided and erected
at both sides of gate ( door of 3 mt x 1.85 mtr.)
No 7821.00 7821.00 7821.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/G/24 Scrapping the existing paint & Painting of steel
tubular pole / RSJ / channel/ pipe pole with brackets
with 1 coat of red oxide paint and 2 coats of
aluminum paint.
R.M 41.00 41.00 41.00
Elec/G/25 Spray painting to distribution transformer on field
with one coat of red oxide and two coats of best
quality enamel paint without any damages in an
approved manner.
a) Upto 200 KVA capacity. Job 2156.00 2156.00 2156.00
b) Above 200 KVA capacity Job 3091.00 3091.00 3091.00
Elec/G/26 Painting to fencing of transformer sub-stn including
all supports, ironwork and doors from both sides
with two coats of aluminum paint in an approved
manner.
Sqm 104.00 104.00 104.00
Elec/G/27 Providing and erecting individual CT & PT unit on
provided cross arm with necessary fixing
arrangement and earthing terminals.
a) 11 KV CT No. 10725.00 10700.00 10190.00
b) 11 KV PT No. 11935.00 11900.00 11340.00
c) 22 KV CT No. 11935.00 11900.00 11340.00
d) 22 KV PT No. 12600.00 12000.00 11970.00
Elec/G/28 Providing, erecting 2 x 2.5 sq.mm multi-strand
copper armoured cable (for CT & PT unit) with
necessary clamping arrangement.
R.M 130.00 130.00 120.00
Elec/G/29 Inspection of faulty distribution transformer 11 kV or
22 kv on HV side, 433 V on LV side upto 500 KVA
capacity in workshop in presence of authority by
opening top cover disconnecting HV & LV studs, tap
changer connections, taking out core along with
winding for inspection and carrying out necessary
tests on HV, LV side, oil, tap-changer etc checking
breather, body condition etc and submitting
inspection report and quotation for repairs.
(excluding transportation)
Job 1400.00 1400.00 1400.00
Elec/G/30 Erecting 11 kv or 22 kV on HV side 433 V on LV
side upto 500 KVA capacity hired/ provided
transformer on existing plint/ DP structure, making
connections on HV/LV side in approved manner,
carrying out necessary tests before and after
charging to required load to satisfaction.
Job 3500.00 3500.00 3500.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/G/31 Supplying and erecting XLPE armoured cable for
11 kV with ISI mark standard aluminium wire
erected on pole with 25/3 MS clamps/ provided
trench/ laid in provided pipe in an approved manner
a) 3 core x 70 sq.mm R.M 750.00 750.00 750.00
b) 3 core x 95 sq.mm R.M 875.00 875.00 875.00
c) 3 core x 120 sq.mm R.M 1000.00 1000.00 1000.00
d) 3 core x 150 sq.mm R.M 1100.00 1100.00 1100.00
e) 3 core x 185 sq.mm R.M 1300.00 1300.00 1300.00
f) 3 core x 240 sq.mm R.M 1600.00 1600.00 1600.00
g) 3 core x 300 sq.mm R.M 1800.00 1800.00 1800.00
h) 3 core x 400 sq.mm R.M 2200.00 2200.00 2200.00
Elec/G/32 Supplying and erecting XLPE armoured cable for
22 kV with ISI mark standard aluminium wire
erected on pole with 25/3 MS clamps/ provided
trench/ laid in provided pipe in an approved
manner.
a) 3 core x 70 sq.mm R.M 1100.00 1100.00 1100.00
b) 3 core x 95 sq.mm R.M 1150.00 1150.00 1150.00
c) 3 core x 120 sq.mm R.M 1300.00 1300.00 1500.00
d) 3 core x 150 sq.mm R.M 1400.00 1400.00 1400.00
e) 3 core x 185 sq.mm R.M 1500.00 1500.00 1500.00
f) 3 core x 240 sq.mm R.M 1800.00 1800.00 1800.00
g) 3 core x 300 sq.mm R.M 2000.00 2000.00 2000.00
h) 3 core x 400 sq.mm R.M 2300.00 2300.00 2300.00
Elec/G/33 Supplying and erecting XLPE armoured cable for
33 kV with ISI mark standard aluminium wire
erected on pole with 25/3 MS clamps/ provided
trench/ laid in provided pipe in an approved
manner.
a) 3 core x 70 sq.mm R.M 1550.00 1550.00 1550.00
.
b) 3 core x 95 sq.mm R.M 1600.00 1600.00 1600.00
c) 3 core x 120 sq.mm R.M 1700.00 1700.00 1700.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
d) 3 core x 150 sq.mm R.M 1800.00 1800.00 2200.00
e) 3 core x 185 sq.mm R.M 1900.00 1900.00 1900.00
f) 3 core x 240 sq.mm R.M 2000.00 2000.00 2000.00
g) 3 core x 300 sq.mm R.M 2100.00 2100.00 2100.00
h) 3 core x 400 sq.mm R.M 2400.00 2400.00 2400.00
Elec/G/34 Supplying and jointing XLPE cable jointing kit
straight through type for 11 kV XLPE cable.
a) 70/95 sq.mm. Cable No. 19000.00 19000.00 18050.00
b) 120 to 185 sq.mm. Cable No. 22700.00 22700.00 21550.00
c) 240 to 400 sq.mm. Cable No. 25000.00 25000.00 23750.00
Elec/G/35 Supplying and jointing XLPE cable jointing kit
straight through type for 22 kV XLPE cable.
a) 70/95 sq.mm. Cable No. 34000.00 34000.00 32300.00
b) 120 to 150 sq.mm. Cable No. 36000.00 36000.00 34200.00
c) 185 to 240 sq.mm. Cable No. 39000.00 39000.00 37000.00
d) 300 to 400 sq.mm. Cable No. 51300.00 51300.00 48700.00
Elec/G/36 Supplying and jointing XLPE cable jointing kit
straight through type for 33 kV XLPE cable.
a) 70 sq.mm. Cable No. 39000.00 39000.00 37000.00
b) 95 to 150 sq.mm. Cable No. 44000.00 44000.00 41800.00
c) 185 to 300 sq.mm. Cable No. 67700.00 67700.00 64300.00
d) 400 sq.mm. Cable No. 75000.00 75000.00 71250.00
Elec/G/37 Supplying and jointing XLPE cable jointing kit (end
termination kit.) for 11 kV XLPE cable
a) Indoor type
1) 70 to 95 sq.mm. Cable No. 7000.00 7000.00 7000.00
2) 120 to 185 sq.mm. Cable No. 7500.00 7500.00 7500.00
3) 240 to 300 sq.mm. Cable No. 8300.00 8300.00 8300.00
4) 400 sq.mm. Cable No. 8800.00 8800.00 8800.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
b)Outdoor type
1) 70 to 95 sq.mm. Cable No. 11500.00 11500.00 11500.00
2) 120 to 185 sq.mm. Cable No. 12000.00 12000.00 12000.00
3) 240 to 300 sq.mm. Cable No. 13000.00 13000.00 13000.00
4) 400 sq.mm. Cable No. 14000.00 14000.00 14000.00
Elec/G/38 Supplying and jointing XLPE cable jointing kit (end
termination kit.) for 22 kV XLPE cable.
a) Indoor type
1) 70 to 120 sq.mm. Cable No. 9400.00 9400.00 9400.00
2) 150 to 185 sq.mm. Cable No. 11000.00 11000.00 11000.00
3) 240 to 400 sq.mm. Cable No. 13000.00 13000.00 13000.00
b)Outdoor type
1) 70 to 120 sq.mm. Cable No. 15000.00 15000.00 15000.00
2) 150 to 185 sq.mm. Cable No. 17000.00 17000.00 17000.00
3) 240 to 400 sq.mm. Cable No. 22000.00 22000.00 22000.00
Elec/G/39 Supplying and jointing XLPE cable jointing kit (end
termination kit.) for 33 kV XLPE cable.
a) Indoor type
1) 70 to 95 sq.mm. Cable No. 12000.00 12000.00 12000.00
2) 120 to 185 sq.mm. Cable No. 19000.00 19000.00 19000.00
3) 240 to 400 sq.mm. Cable No. 21000.00 21000.00 21000.00
b) Outdoor type
1) 70 to 95 sq.mm. Cable No. 20000.00 20000.00 20000.00
2) 120 to 185 sq.mm. Cable No. 26000.00 26000.00 26000.00
3) 240 to 400 sq.mm. Cable No. 34000.00 34000.00 34000.00
Note :- For structural steel work refer item of civil
DSR
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/G/40 Supplying and erecting rolled steel Joist (girder)
pole of 116 x 100 x 11 m. Long (as per IS-2062) for
H.T. line / D.P. structure with proper allignment and
keeping it in truely vertical position and erected in
provided C.C. foundation and plinth with
arrangement for connecting earth terminals of
suitable size. The pole shall be burried atleast 1.80
m. Below the ground level.
No. 17000.00 17000.00 17000.00
NOTE :- Rates for 9/10/12 m. Poles can be worked
out on running meter basis accordingly.
Elec/G/41 Supplying and erecting rolled steel Joist (girder)
pole of 125 x 70 x 8 m. Long (as per IS-2062) for
L.T. line with proper allignment and keeping it in
truely vertical position and erected in provided C.C.
foundation and plinth with arrangement for
connecting earth terminals of suitable size. The
pole shall be burried atleast 1.50 m. Below the
ground level.
No. 8000.00 8000.00 8000.00
NOTE :- Rates for 9/10/11 m. Poles can be worked
out on running meter basis accordingly.
Elec/G/42 Supplying and erecting including fabrication of MS
brackets, V cross arms, single pole cut point,
support structures out of suitable channels / angles
etc.complete.
Kg. 65.00 65.00 60.00
Elec/H/1 Supplying at departmental store and testing at site
Bi-directional elevated type high intensity runway
edge light fixture & threshold light fixture complete
with lens holder, lens clamping mechanism, pre
focus lamp holder, central column assembly,
breakable coupling, gaskets, two pin secondary
lead, base plate with six Nos of stainless steel bolts,
spring and plain washers, 200 W. 6.6 Amp/6.6
Amp 50 Hz 5000 V, clear asymmetrical lens, 2
nos. filters and all other accessories complete in all
respect confirming to the FAA specification with Bi-
pin halogen lamp 200 watt, 6.6 Amp suitable for
HIRL fitting complete as required.
No. 11884.00 11884.00 11300.00
Electrical -H-Night Landing of Air Strips.
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Elec/H/2 Supplying at departmental store and testing at work
site omni-directional elevated type medium intensity
/ apron/edge turning pad light fixture complete with
lens holder, lens clamping mechanism, pre focus
lamp holder, central column assembly, breakable
coupling, gaskets, two pin secondary lead, base
plate with six nos. stainless steel bolts, spring and
plain washers, 45 watt, 6.6/6.6 Amp. 50 Hz, 5000
Volt series type tubular runway lamp (T-10) of 1000
hours Burning average life with P-28S capacity
confirming to the FAA specifications complete with
blue lens and all other accessories complete in all
respects as required.
No. 7605.00 7605.00 7300.00
Elec/H/3 Supplying at departmental store and testing at work
site PAPI (comprising of 4 assemblies in a set at
each end) for 6.6 Amp series current system
complete with 3 nos. 200 W, 6.6 amps lamps
assembly halogen lamps, holder/ pins adjustable
legs with breakable couplings, filters, spreader
assembly, secondary leads of standard length (2.5
meters) with plugs and dust proof housing with air
filter etc. 200 w, 6.6/ 6.6 Amp 50 Hz, 5000 V,
complete with all accessories as per FAA
specifications L-880 & L-881 ready for installation
as required with the help of provided set of special
tools & alignment device set
Set 426778.00 426778.00 402700.00
Elec/H/4 Supplying at departmental store and testing at work
site 16 sq. mm., 5 KV grade PVC insulated and
PVC sheathed, stranded copper conductor, un-
armoured single core, airport lighting cable
confirming to IS 1554 Part-II with up to date
amendments.
R.M 174.00 174.00 160.00
Elec/H/5 Supplying at departmental store and testing at work
site 6 sq. mm., 5 KV grade PVC insulated and PVC
sheathed, stranded copper conductor, un-armoured
single core, airport lighting cable confirming to IS
1554 Part-II with up to date amendments.
R.M 112.00 112.00 105.00
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Supplying at departmental store and testing at work
site 6.6 Amp 5 KV of series type air port lighting
isolating transformer encapsulated on polyester
resign finally moulded in neoprene type rubber with
primary and secondary connection leads in C.I.
Transformer housing box water tight round type
metal container of outside dia 300 mm and 450
height made of 10 mm thick all round except on top
surface which is 15 mm thick cast iron moulding
suitable to receive a light fitting base plate on the
top and underground housing associated with
transformer power cable and having a clear hole
centre at one side surface centre 3" above bottom
surface suit able to receive 2" dia "B" class G.I. pipe
and check nuts having two earth bolts of M 10 x 30
mm welded inside near the hole (4" away from the
hole central) and having a drain hole at the bottom
suitably taped to receive//2" dia "B" class G.I. pipe
and having a clear opening of 220 mm at the top
surface and 6 Nos M 10 tapered holes at the hole
centre of 260 mm to receive light fitting base plate
and bolts as required.
a) For 200 watt isolating transformer No 7801.00 7801.00 7300.00
b) For 45 watt isolating transformer No 7301.00 7301.00 7100.00
Elec/H/7 Supply of 5 KV grade plug and receptacle of type 1
class "B" connector and suitable for field
attachment with 5 KV grade PVC insulated PVC
sheathed Single core 16 Sq.mm. copper conductor
cable confirming to the specified specification etc.
Complete as required.
No. 596.00 596.00 570.00
Elec/H/8 Supplying at departmental store and testing at work
site indoor type air cooled constant current
regulator thyristor control electronic type suitable for
use on 415 V, 50 Hz input A.C. system with output
power of 30 KW at 6.6 Amp. With 5 step variation of
current output (6.6, 5.2, 4.1, 3.4 and 2.8 Amps.)
suitable for local and remote control operation with
suitable control supply complete with digital output
ammeter (0-10 A) over current, over voltage, earth
fault protections and earth leakage meter, positive
back indication equipment complete with 5 KV
grade current transformer of rating 20-10/1 A and
relay contacts, inter connection with multi-core
control cable, junction box etc. complete in all
respect as required.
Set 370344.00 370344.00 352500.00
Elec/H/6
Item No. Descriptions Unit
Mumbai Pune/
Nanded
Nagpur
2013-2014
Ele/H/9 Supplying at departmental store and testing at work
site indoor type air cooled constant current regulator
thyristor control electronic type suitable for use on
230 or 415 V, 50 Hz input A.C. system with output
power of 4 KW at 6.6 Amp. With 3 step variation of
current output (6.6, 4.1 and 2.8 Amps.) suitable for
local and remote control operation with suitable
control supply complete with digital output ammeter
(0-10 A) over current, over voltage, earth fault
protections and earth leakage meter, positive back
indication equipment complete with 5 KV grade
current transformer of rating 20-10/1 A and relay
contacts, inter connection with multi-core control
cable, junction box etc. complete in all respect as
required.
Set 158719.00 158719.00 151700.00
Ele/H/10 Supplying at departmental store and testing at work
site underground/ aboveground of 37 core 2.5
sq.mm. cooper conductor control cable of 1.1 KV
grade PVC insulated and PVC sheathed armoured
cable confirming to IS 1554 Part-I 1976 with upto
date amendments complete as required.
R.M 999.00 999.00 800.00
Ele/H/11 Supplying at departmental store and testing at work
site HT straight through joint with epoxy resin
including ferrules and other jointing materials for
PVC insulated and PVC sheathed copper conductor
single core cable 5 KV grade 16 sq.mm. size
complete as required.
Set 1389.00 1389.00 970.00
Ele/H/12 Supplying at departmental store and testing at work
site HT straight through joint with epoxy resin
including ferrules and other jointing materials for
PVC insulated and PVC sheathed copper conductor
single core cable 5 KV grade 6 sq.mm. size
complete as required.
Set 1310.00 1310.00 970.00
Ele/H/13 Supplying at departmental store and testing at work
site Junction box for remote control operation with
37 core cable etc complete
Set 4785.00 4785.00 3560.00