91

ELECTRICAL CABLE ASSEMBLIES

Fleetcraft Coiled Cable Assemblies• Remains flexible in low temperature• Excellent long life memory.• Tough black jacket resists abrasion, common

commercial degreasers, solvents.• Phillips Die-cast metal plugs with springs.

Heavy Duty, 6 12-Gauge Wires, 1 10-Gauge WireWorking Length Part No.

12 Foot T-E-101018615 Foot T-E-1010188

Economy, 6 14-Gauge Wires, 1 12-Gauge Wire12 Foot T-E-101018515 Foot T-E-1010187

One 10-Gauge, six 12-Gauge WiresOne Angled, one straight plug

Working Length Part No.19 Foot with two 12 inch leads T-E-GR87024

Grote UltraLink Power CordCoiled Cable Assembly19 foot working Length

Extra power delivery for single or doubleconfigurations exceeding minimum legal lamprequirements.

• Remains flexible at -55° to 190° F.• Extra tough urethane jacket material• Completely sealed to prevent corrosion.• Shock proof, solid molded elastomeric plug body.• Exceeds SAE J1067 and J2222 requirements.

PHILLIPS ABS PERMACOIL™

• Comes with two 15-730 plugs.• Bright Green Jacket• Good Abrasion reistance• -87° to +150 temperature range• Good recoil memory,and large finger grips.

Working Length Part No.12 Foot T-E-30-432115 Foot T-E-30-4621

15 Foot with 48" lead T-E-30-4921

92

ELECTRICAL CABLE ASSEMBLIES

Phillips Duracoil TM

Heavy Duty Cable Assemblies• Remains flexible from -87° F to 195° F.• Superior long life memory, flexibility, and

abrasion resistance.• Black jacket with nylon Permaplugs• Standard with anticorrosive lithium grease for

longer life.• Meets or exceeds SAE J560 or J2222.

Heavy Duty, 6 12-Gauge wires, 1 10-Gauge WireWith 2 Metal Plugs with Springs

Working Length Part No.12 Foot with one 6 foot lead T-E-22-9521

With 2 Nylon PermaplugsWorking Length Part No.

15 Foot with one 6 foot lead T-E-22-9720

The Phillips LECTRACOILTM provides the following totractor manufacturers in North America:

(1) 8 Ga. white ground(1) 10 Ga. red stop light(1) 10 Ga. blue (ABS power)(4) 12 Ga. brown, black, yellow, green, for

conventional trailer lighting.LECTRACOILTM 4/12, 2/10, 1/8 Ga.

With 2 PermaplugsWorking Length Part No.

15 ft. T-E-30-962015 ft., With 40" Lead T-E-30-9920

With 2 Metal PlugsWorking Length Part No.

15 ft. T-E-30-9621

Phillips ABS LECTRACOIL TM

The NHTSA approved method for powering trailers and dolly ABS systems requires a separate,constant power circuit (Blue) and a standby circuit (Red). The RP137 issued by the Maintenance Council (TMC)division of the ATA, recommends power availability to the electrical coil cord of the tractor of 10 amps at 12.5 volts forthe blue (auxiliary) and red (stoplight) circuit. The ABS LECTRACOIL TMcomplies with all of the above. TheLECTRACOIL TM is provided with the same durable jacketing as the Duracoil, in a distinctive "lectra green" colorwhich provides instant recognition. Exceeds SAE J2222.

Phillips Duracoil TM

Anti-Lock (FMVSS-121)• 7 conductors in red jacketing• Remains flexible from -87° F to 195° F.• Primarily considered OEM quality by its

distinctive red jacket. Designed to be used forall longer single, double and triple applications.

• Meets SAE J1067• All connector pins are double crimped for

maximum conductivity and durability andmeets SAE J560B.

5/12-Gauge , 1/10-Gauge, 1/8 GaugeWith 2 Permaplugs (Illustration shows 2 metal plugs)

Working Length Part No.15 Foot with 40" lead T-E-32-9920

93

ELECTRICAL CABLE ASSEMBLIES

6/12-Gauge, 1/10-GaugeLength Part No.12 Foot T-E-22-205115 Foot T-E-22-2071

Duraflex Straight Cable Assembly7 Conductor

• Operational from -40° F to 175° F• Plugs equipped with strain-relief springs• Plugs protected with anticorrosive grease• Connector pins meet SAE J560• Rated at 110 amps - continuous service

4 Gauge Fine Strand CopperWorking Length Part No.

12 Foot T-E-23-432515 Foot T-E-23-4625

Single PoleCoiled Lift Gate Cable Assembly

• Operational from -50° F to 150° F• Used for lift gate and remote battery charging

applications - has dark green jacket• Maximum current carrying capacity 200 amps• Coil exceeds SAE J2222• Includes 2 single pole plugs with springs

Six Conductor, 10' Mini-Coil

Phillips Heavy DutyPermacoil Cable Assemblies

• Remains flexible in low temperatures• Excellent long life memory.• Blue jacket with nylon Permaplugs• Standard with anticorrosive lithium grease for

longer life.

Heavy Duty, 6 12-Gauge Wires, 1 10-Gauge WireWorking Length Part No.

12 Foot T-E-22-4320

6 14-Gauge Wires, two 15-610 plugsWorking Length Part No.

10 Foot T-E-19-6710

94

ELECTRICAL WIRE & TRAILER CABLE

PVC Insulated Primary WireColor 14 Gauge 12 Gauge 10 GaugeBlack T-E-2-121 T-E-2-131 T-E-2-141Blue T-E-2-122 T-E-2-132 T-E-2-142Brown T-E-2-123 T-E-2-133 -Green T-E-2-124 T-E-2-134 T-E-2-144Red T-E-2-125 T-E-2-135 T-E-2-145White T-E-2-126 T-E-2-136 T-E-2-146Yellow T-E-2-127 T-E-2-137 T-E-2-147

FleetcraftTM Bulk Trailer CableNo. of Wire

Part No. Wires Gauge PackT-E-1011861 4 14 100'T-E-1011861-500 4 14 500'T-E-1094755 6 14 100'T-E-1094755-500 6 14 500'T-E-1010126 7 6-14/1-12 100'T-E-1010126-500 7 6-14/1-12 500'T-E-1011410 7 6-12/1-10 100'T-E-1011410-500 7 6-12/1-10 500'

Bulk Trailer Cable• Flexible, soft annealed copper wires.• Jacket resists damaging common chemicals• Wire colors meet ATA, TMC, and SAE recommendations

Primary Wire in100 Foot Spools

• Soft Annealed Copper• Resists most chemicals,

moisture, abrasion• SAE J1128

Phillips ABS LECTRAFLEX TM

7 Conductor ABS Cable(1) 8 Ga. white ground(1) 10 Ga. red stop light(1) 10 Ga. blue (ABS power)(4) 12 Ga. brown, black, yellow, green, for

conventional trailer lighting.The LECTRAFLEXTM is provided with the same durablejacketing as the Duracoil, in a distinctive "lectra green"color which provides instant recognition.Exceeds SAE J2222.

7 Conductor LECTRAFLEXTM ABS CableLECTRAFLEXTM 4/12, 2/10, 1/8 Ga.

2 Conductor Jacketed Parallel CableBlack and white conductors, heavy duty

extruded gray jacket over 2 primary conductors.Package Length 100 ft.

Part No. GaugeT-E-2-402 14/2 Ga.T-E-2-403 12/2 Ga.

Part No. T-E-3-327Package Length

100 Foot

Part No. T-E-30-205112 Foot Straight w/15-30 metal plugs

Part No. T-E-30-207130 Foot Straight w/15-30 metal plugs

95

PLASTIC LOOMPolyethylene Split Loom• Split seam feature allows for easy

wire insertion and service.• Excellent for high heat, high

abrasion applications.• UV stabilized, black in color

Part No. I.D. Part No. I.D.T-E-5-023 1/4" T-E-5-029 5/8"T-E-5-025 3/8" T-E-5-030 3/4"T-E-5-027 1/2" T-E-5-032 1"

INSULATED WIRE CONNECTORSWatertight Shrink and Seal

Insulated Ring TerminalsCrimp, heat, and shrink to fit for watertight connection

16 - 14 Gauge (Blue) 12 - 10 Gauge (Yellow)Ring Size Part No. Ring Size Part No.

3/8 T-E-1-1926 1/2 T-E-1-19375/16 T-E-1-1925 3/8 T-E-1-19361/4 T-E-1-1924 5/16 T-E-1-193510 T-E-1-1923 10 T-E-1-19338 T-E-1-1922 8 T-E-1-1932

Stud Hole Sizes8 10 1/4 5/16 3/8 1/2

Watertight Shrink and SealInsulated Butt Connectors

Crimp, heat, and shrink to fit for watertight connection12 - 10 Gauge 16 - 14 Gauge 22- 18 Gauge

(Yellow) (Blue) (Red)Part No. Part No. Part No.

T-E-1-1963 T-E-1-1962 T-E-1-1961

Crimp Type Vinyl Insulated Ring TerminalsTo avoid corrosion from moisture, heat shrink tubing is

recommended after crimping for a watertight connection.12-10 Gauge (Yellow) 16 - 14 Gauge (Blue)Ring Size Part No. Ring Size Part No.

3/8 T-E-1-2126 3/8 T-E-1-21455/16 T-E-1-2125 5/16 T-E-1-21461/4 T-E-1-2124 1/4 T-E-1-214410 T-E-1-2123 10 T-E-1-21438 T-E-1-2122 8 T-E-1-2147

6 T-E-1-2142

Stud Hole Sizes6 8 10 1/4 5/16 3/8

Crimp and heat for a watertight connection

Crimp and heat for a watertight connection

To avoid corrosion from moisture, heat shrink tubing isrecommended after crimping for a watertight connection.

Crimp Type Insulated Butt ConnectorsTo avoid corrosion from moisture, heat shrink tubing is

recommended after crimping for a watertight connection.Vinyl Insulation Nylon Insulation

Gauge Part No. Gauge Part No.12 - 10 (Yellow) T-E-1-2620 12 - 10 (Yellow) T-E-1-226316 - 14 (Blue) T-E-1-2640 16 - 14 (Blue) T-E-1-226222 - 18 (Red) T-E-1-2660 22 - 18 (Red) T-E-1-2261

LOOM

96

INSULATED WIRE CONNECTORS

Crimp Type Slide Terminals12 - 10 Ga. (Yellow) 16 - 14 Ga. (Blue)Vinyl Nylon Vinyl Nylon

T-E-1-2312 T-E-1-2274 T-E-1-2314 T-E-1-2272

12 - 10 Ga. (Yellow) 16 - 14 Ga. (Blue)Vinyl Nylon Vinyl Nylon

T-E-1-2273 T-E-1-2273 T-E-1-2324 T-E-1-2271

3 Way TerminalFor 16 - 14 Gauge Wire

Part No. T-E-1-2193

Self Stripping Quick Lock ConnectorsWire Size Color Part No.18 - 14 Ga. Blue T-E-1-2335

Economy Crimp Type Insulated Butt ConnectorsPlastic PVC insulated sleeve in quantities of 100

Gauge Part No.12 - 10 (Yellow) T-E-YB10016 - 14 (Blue) T-E-BB10022 - 18 (Red) T-E-RB100Our economy connectors - quality at a lower price.

NYLON CABLE TIES

Standard Cable TiesMax. Tensile

Bundle Strength PackLength Color Dia. (lbs.) Size Part No.

4" Natural 4" 18 100 T-E-1-40018" Natural 2" 50 100 T-E-GR83-6818

151/4" Natural 4" 50 100 T-E-GR83-6826151/4" Natural 4" 120 100 T-E-GR83-6828

21" Black 6" 175 25 T-E-T150MOX2

Economy ConnectorWire Size Color Part No. Pack Qty.18 - 14 Ga. White T-E-BC50 50

Spade Type WIre ConectorPart No. Gauge Stud Size

T-E-1-2443 16-14 Ga 10 Spade

97

BATTERY AND STARTER CABLE

Part No. Size Strands Color O. D.T-E-3-503 4 Ga. 133 x 26 Red .390T-E-3-504 4 Ga. 133 x 26 Black .395T-E-3-505 2 Ga. 133 x 24 Red .435T-E-3-506 2 Ga. 133 x 24 Black .435T-E-3-510 1/0 Ga. 133 x 21 Black .555T-E-3-511 2/0 Ga. 259 x 23 Red .595T-E-3-512 2/0 Ga. 259 x 23 Black .595T-E-3-514 3/0 Ga. 259 x 22 Black .670

Battery And Starter Cable

• 25 Foot lengths• Rope stranded for increased flexibility• Made of soft annealed, fully stranded

copper conductors

BATTERY TERMINALS

Crimpable Copper90 Right Angle

Part Wire PostNo. Gauge Type

T-E-7-535 2/0 Pos.

Crimpable CopperClosed End Elbow Right

Part Wire PostNo. Gauge Type

T-E-7-557 2/0 Neg.

Crimpable CopperPost Type

Part Wire PostNo. Gauge Type

T-E-7-511 1/0 PosT-E-7-513 1/0 Neg

PosNeg

T-E-7-515 2/0T-E-7-517 2/0

3/8" Stud MountedGroup 31

Single BarrelPart WireNo. Gauge

T-E-7-574 2/0

3/8" NutCorrosion resistant nut

for Group 31terminal securement

Part No. T-E-7-186

Lead Charging PostFor 3/8" Stud TypePart No. T-E-7-155

Tin Plated CopperGround Lugs

• Flared Opening• Crimp or Solder

Part StudNo. Gauge Size

T-E-7-203 2/0 PosT-E-7-204 2/0 Neg

Heavy Duty All CopperGround Lugs

• Flared Opening• Crimp or SolderPart StudNo. Gauge Size

T-E-7-102 4 1/4"T-E-7-103 4 5/16"T-E-7-104 2 3/8"T-E-7-107 1/0 3/8"T-E-7-109 2/0 3/8"T-E-7-110 2/0 1/2"T-E-7-111 3/0 5/16"T-E-7-112 3/0 3/8"T-E-7-113 3/0 1/2"T-E-7-114 4/0 3/8"T-E-7-115 4/0 1/2"

Battery to BatteryCable, Group 31 (A)

Part No. Gauge LengthT-E-058-118 2 8"

Battery to Battery Cable, Group 31

Ground Strap

2/0 copper terminals with shrink tubing

Ground Strap (B) Part No. Gauge Length

T-E-9-150 4 12"

Circuit Breaker150 AMP Manual ResetPart No. T-E-54-872PL

98

SHRINK TUBING, ACCESSORIESAn easy to use tubing that shrinks without melting - justslip over wire or splice and heat. Inner wall melts,providing a moistureproof connection.

• Color Coded• Insulates wire splices• Reinforces the terminal/wire connection

Single Wall for Primary WireI. D. I. D. Wire

Part No. Before After Color SizeT-E-6-102 1/8" 1/16" Red 18T-E-6-104 3/16" 1/8" Blue 16-14T-E-6-106 1/4' 1/8" Yellow 12-10

Dual Wall for Primary WireI. D. I. D. Wire

Part No. Before After Color SizeT-E-6-202 3/8" 1/8" Black 8T-E-6-204 1/2" 1/8" Black 6-2T-E-6-206 11/8' 3/8" Black 4/0-1T-E-6-207 11/8" 3/8" Red 4/0-1

ELECTRICAL TAPE BATTERY POST CLEANER

Heavy Duty batteryPost & Terminal BrushPart No. T-E-4-120

All Purpose GradeVinyl Electrical Tape7 Mil, 3/4" Wide,60 Foot RollsUL ListedPart No. T-E-10200ET

SWITCHESPush - Pull SwitchExtra Heavy Duty 2 Position6 - 28 Volts - 75 Amp S.P.S.T.Off-On Heavy duty die castbody, chrome plated knob,copper terminals. Mountingstem 5/8" long,15/32" diameter.Part No. T-E-35-306

Push - Pull SwitchModerate duty, 2 position.Off-On 25 amp at 6V,15 Amp at 12V.Mounting stem 5/8" long,7/16" diameter.Ivory plastic knob.Part No. T-E-35-300

Push - Pull SwitchHeavy DutyMounts through 5/8" diameterhole. Illuminated knob, 20 ampcapacity, single pole normallyopen circuit.Part No. T-E-TL102

Toggle Switches6 - 24V, 50 AmpMOM On-Off MOM OnS.P.D.T. 3 Positions/ 3 ScrewTerminalsPart No. T-E-34-215

On-Off-On S.P.D.T. 3 Positions/3Screw TerminalsPart No. T-E-34-218

Toggle Switch6 - 24V, 50 Amp.On - Off S.P.S.T.2 Positions,2 Screw TerminalsPart No. T-E-34-212

Toggle Switch6 - 24V, 50 Amp.On - Off S.P.S.T.2 Positions,2 Screw Terminals11/2" Long Bat handlePart No. T-E-34-213

Keyed On/Off Switch2 hole mounting patternPart No. T-E-31-602

99

SWITCHES

Toggle Switch6 - 24V, 50 AmpOn-Off S.P.S.T.2 Positions,2 Screw TerminalsPart No. T-E-34-571

Toggle Switch6 - 24V, 50 AmpOn-Off-On S.P.D.T.3 Positions3 Screw TerminalsPart No. T-E-34-573

Toggle Switch6 - 24V, 50 AmpMOM On-Off MOM OnS.P.D.T. 3 Positions/3 Screw TerminalsPart No. T-E-34-575

Toggle Switch6 - 24V, 50 AmpOn-On D.P.D.T.2 Positions6 Screw TerminalsPart No. T-E-34-576

Toggle Switch6 - 24V, 50 AmpOn-Off-On D.P.D.T.2 Positions6 Screw TerminalsPart No. T-E-34-577

Ignition Starter Switch4 position - 2 keys supplied.Terminal nuts, lock washers, hexback nut, knurled face nutsupplied, diecast housing.Fits panel with 3/4" hole.Part No. T-E-31-103

SwitchBackup LampUniversal type.2 threaded studs.Part No. T-E-21-361

SwitchBackup Lamp2 screwterminals.

ReplacesKenworth, K30133, Freightliner 06-10525, Mack 1MR2297, othersPart No. T-E-21-361

Momentary Start Switch60 amps at 12V, 40 amps at 24V.Weather and dustproof.

Part No. T-E-24-360

RockerSwitchUniversal,snap in typemountingbracket.35A-12V Red

pilot light. On - Off S.P.S.T.2pos/3 screw terminals. Whiteactuator, nickel plated bezel.Part No. T-E-34-305

Dimmer SwitchUniversal - with 3 flatscrew terminals and4 bullet terminalssupplied in separatehardware kit. 3screw terminals.Part No. T-E-52-250

Replaces Delco-remy 465-A, B, E, H, J, K,R, S, V, W, X, Z; 471P, R, T, W, Z,1997002, 3, 6, 7, 8, 9, 10, 11

Dimmer SwitchFloor mounted type,3 special terminals.Part No. T-E-52-251

Replaces: American Motors 3156124,3160926, Chrysler 1841895, 1881938,2291202, Ford B9A-13532A (2701524)

Dimmer SwitchFloor mounted type,3 special terminalsPart No. T-E-52-252

Replaces: Ford COTF-13A024A,COTZ-13A024A

Dimmer SwitchSpecial floormounted type, 3special terminals forplug connection.Part No. T-E-52-253

Replaces: Delco-Remy 1997028, 1997031,1997035, 1997036, 1997037, 3841892,GM 538446, 539288, 578005

ACCOFF

IGN & ACC

IGN

START

Breakaway SwitchReinforced nylon case, silvercontact points, nylon pull pin.

Part No. T-E-BE2010

100

SWITCHESMaster Disconnect Switch

Lever operated - 6 - 36V;180 amps continuous capacity;1000 amps in rush. S.P.S.T. (Off-On)

2 stud terminals forbattery circuit only. Doesnot disconnect alternatoror generator filed circuit.On vehicles equippedwith alternators enginemust be shut off to avoidpotential damage toalternator diodes.Instruction sheet included.Part No. T-E-51-302

Master Disconnect SwitchLever operated - 6 - 36V;D.P.S.T. (Off-On) 4 stud terminalsfor battery and alternator or generator field circuit.Designed to break alternator generator circuit priorto battery circuit disconnect. Use for gasoline and oiltank trucks as well as other applications.

Two 3/8" and two 10-32copper alloy stud terminals.Instruction sheet included.Part No. T-E-51-304

Axle Switch2 positions, both on controls. High andlow axle ranges. Die cast bodyprotected by rubber cover. Threefemale terminals to receive bulletterminals. Large red knob. For use

with eaton 2 speedrear axle.

Part No. T-E-52-261.NGI )1(TRATS

SWITCH

BAT. STARTER

Starter Solenoid SwitchUniversal - 12V applications -grounded base, flat bracket,internally grounded to housing, otherend connected to small terminal.Part No. T-E-52-305

Starter Solenoid Switch12V grounded base, flat bracket,breather cap.Part No. T-E-52-306

.NGI )1(TRATSSWITCH

BAT. STARTER

Replaces: Ford C7AF-11450A,C6AZ-11450A, C9AZ-11450A

)S(.TAB STARTSWITCH

BAT. STARTER

Solenoid SwitchContinuous duty. Solinoid insulated.

With hardware.Flat bracketPart No. T-E-52-307

Replaces: Delco 1114218, 223; Prestolite15-132, 133, 236, 311, SAS-4201, 4202,4213, 5203

Heavy Duty 2 to 18 Bulb Turn SignalSwitch with High/Low Beam

• 6 - 12V, eighteen 32 c. p. bulbs• Universal replacement with lift handle

headlight dimmer• Black finish• Grease-free contact area• Harness sold separately

Part No. T-E-GR48282

Turn Signal Switch, Flat Black• 12V• 10 Wire harness• Signal arm features built-in push

button high/low beam selector switch• 10 bulb capacity for hazard warning,

5 bulbs per side for turn signalflashing

Part No. TL129Replacement relay for TL905

Part No. T-E-TL905Part No. T-E-TL900

• Surpasses SAE J589 & J910 standards for turn & hazard functions• Improved, light weight, nylon housing & handle• Capable of flashing 18 lamps in hazard mode (9 lamps per side for turn

signal flashing)• 960 wiper options include 7 speed intermittent, two speed

(hi/low) or omitted• 961 wiper option includes two speeds (hi/low)• Improved design eliminates premature breakage & component wear• Feature Lift-to-Dim & Flash-to-Pass options• Brake overrides hazard function lights when brake pedal is depressed• Material: Glass filled nylon housing

960 Series Self-Canceling Turn Signal Switches

Part No. T-E-TL91250Turn Signal Switch

Turn Signal Switch, Flat Black• 12V• 7 Wire harness• Heavy Duty Die Cast Housing• Durable Die Cast Handle• Heavy Duty flare tab for hazard warning• Heavy gauge mounting strap and hardware• Pilot Light for Turn Signal and Hazard• 10 bulb capacity for hazard warning,

5 bulbs per side for turn signal flashing

101

FLASHERS

Signal Stat 12V Everflash2 Prong Flasher16 Bulb capacity for hazard warning.Flashes up to eight 32 cp bulbs per sideplus pilot bulb. 35 amp capacity at 12V.Low profile 11/4" height above terminals.PermastatTM housing. Plug-in mounting oruse 2 mounting holes on 29/16" centersPart No. T-E-TL242

SPADE TYPE FUSES, MISCELLANEOUS CIRCUIT BREAKERS

Part No. Desc ColorT-E-091173 ATO 3 VioletT-E-091175 ATO 5 TanT-E-091177 ATO 71/2 BrownT-E-091180 ATO 10 RedT-E-091181 ATO 15 BlueT-E-091182 ATO 20 YellowT-E-091183 ATO 25 ClearT-E-091184 ATO 30 Green

ATO®

Spade TypeFuses

Direct replacement forATO and ATC style fusesEliminates replacement ofburned out fusesSpecial "snap-off" bladedesign helps minimizeinventoryMeets requirements ofSAE J553C Type l*

Part No. Amp RatingT-E-091072 15T-E-091073 20T-E-091074 25T-E-091075 30

Application GuidePosition Length Vehicle

A .75 Ford TruckB .50 GMC, Ford,

NavistarC .30 Kenworth*Type 1 breakers are designed

to continuously cycle or resetduring an overload situation.

Circuit BreakersUniversal - Meets SAEJ553

Automatic resetLess Mounting BracketPart No. Amp RatingT-E-54-115 15T-E-54-120 20T-E-54-125 25T-E-54-130 30T-E-54-140 40

Blade Type Circuit Breakers

Circuit BreakersUniversal - Meets SAE J553

Automatic resetWith Mounting Bracket

Part No. Amp Rating(A) T-E-54-220 20(A) T-E-54-230 30(B) T-E-54-520 25(B) T-E-54-530 30

(B)

(A)

Snap-In Circuit Breakers12 Volt remote reset circuitbreaker. Replaces glass stylefuses in existing fuse blocks.Opens automatically onoverload. Remains open forprotection until trouble iscorrected.

AmpPart No. RatingT-E-54-410 10T-E-54-415 15T-E-54-420 20T-E-54-430 30T-E-54-440 40

They both have 1-10 Load Lamps,250 total watts, and a frequency of 70-100 FPM

Part No. DescriptionT-E-EL-12 2 Pin, 12VT-E-EL-13 3 Pin, 12V

Operates at 12V or 24VElectronics are sealed in epoxycompound which dissipates heatfrom die cast aluminum housing.Short circuit protected with self-resetting feature. 5 year limitedwarranty. Rated for 35 amp load orsixteen 32/3 cp bulbs. No groundwire required. Meets DOT FMVSS108 and SAEJ945 and J590b.

Part No. T-E-TL97231 Ultraflash w/o audible signalPart No. T-E-TL97232 Ultraflash w/ audible signal

Truck-Lite Ultraflash Heavy DutyElectronic FlasherSolid state

TRIDON Extended Life SuperDuty Electronic SignalFlashers For trucks,buses, RV's andpassenger cars.

Round 2 Prong Flasher12V. Flashes up to three 32 cpbulbs per side, plus pilot bulb.Flashes up to six 32 cp bulbsfor hazard warning. Aluminumhousing.Part No. T-E-552

20 Lamp Heavy DutyElectronic Flasher

• 60 - 120 Flashes per minute• 11 - 15V DC• Only one moving part• Fits standard round socket• 100 hours of continuous

operationPart No. T-E-GR44710

12 Lamp ElectromechanicalFlasher

• 60 - 120 Flashes per minute• 11 - 15V DC• Fits standard round socket• 100 hours of continuous

operationPart No. T-E-GR44530

102

6 & 7 Way ReceptacleWith split pins• 20 amp circuit breakers• For surface mount• Projects 2.56" from

mounting surface• Mounting gasket

includedPart No. T-E-BE24220

W/O Adaptor HousingPart No. Circuit BreakersT-E-BE24015 15 ampT-E-BE24020 20 AmpT-E-BE24030 30 ampT-E-BE24000 None

7 Way Receptacle with Circuit BreakersWith and Without Adaptor Housing

Style A W/Adaptor Housing

Part No. Circuit BreakersT-E-BE24120 20 Amp

Style BW/O Adaptor Housing

Part No. Circuit BreakersT-E-BE24001 None

Style A

Style B

7 Way ReceptacleRing Terminal Type• Housing made of Engineering

Grade Composite• 5°slant for drainage• Lifetime warranty - If cover

breaks off, unit will bereplaced.

• Brass split pinsPart No. T-E-BE23707

7 Way ReceptaclePlug-In Type• Housing made of Engineering

Grade Composite• 5°slant for drainage• Lifetime warranty - If cover

breaks off, unit will bereplaced.

• Brass split pinsPart No. T-E-BE23705

Receptacle Boot• Weather-guard universal

boot• Neoprene - maximum

protection against weatherand ozone

Part No. T-E-15-740

Replacement Cover Kits For Style A (New Style)

Part No. T-E-BQ20014 (Shown)For Style B (New Style)

Part No. T-E-BQ24002

ELECTRICAL PLUGS AND RECEPTACLES

7 Way Nylon Plug• Nylon housing• 100% Brass pins• Uses standard 15-711

replacement insert• Cable guard and compression

cable clamp preventsaccidental cable pull out -the harder it's pulled, thetighter it gets

• Exceeds SAE J560BPart No. T-E-16-730

STA-DRYTM ReceptaclesExclusive design to preventmoisture from entering electricalcircuits. Virtually eliminatescorrosion.• Nylon Housing• Pins insert molded to stay

watertight* Extended barrel for added cable

support

Wire InsertionPart No. T-E-16-720

Ring TerminationPart No. T-E-16-722

Sta-Dry SocketBullet Terminal

Part No. T-E-16-724

103

ELECTRICAL PLUGS AND RECEPTACLES

7 Way Zinc Die Cast Plugs• 100% brass floating pins• Large finger grips• Large interior for ease of wiring• Positive direct drive cable clamp

Part No. DescriptionT-E-15-730 With Spring GuardT-E-15-710 Without Spring Guard

7 Way Zinc Die CastReceptacles• Full opening lid for ease of

plug insertion• Slanted 5 degrees for moisture

drainage• Easily field serviceable• Machined brass pins• Stainless steel lid spring and

hinge pin

Part No. DescriptionT-E-15-720 2-Hole Mount (Shown)T-E-15-722 3-Hole MountT-E-15-724 Insert

7 Way InsertFor 15-720, 15-722Part No. T-E-15-724

STA-DRYTM ReceptaclesWith and Without Circuit Breakers

Glass Filled Nylon and Zinc Die Cast• Waterproof• Molded Insert• Stainless lid spring and hinge pin• Neoprene gaskets• Stackable ground post

Zinc Die CastWith extended barrel for added plug supportWithout 20 Amp 30 AmpBreakers Breakers BreakersT-E-15-760 T-E-15-762 T-E-15-763

Glass Filled NylonWithout 20 Amp 30 AmpBreakers Breakers Breakers

T-E-16-760 T-E-16-762 T-E-16-763

Standard Die Cast Receptacle Housing17/8" Deep, Includes: 15-766 Gasket, 15-765Grommet,2 Hex mounting boltsPart No. T-E-15-769

4 & 6 Way Zinc Die Cast Electrical Plugs

4 Way PlugLess cable guardPart No. T-E-15-410

4 Way Plugwith Cable GuardPart No. T-E-15-430

4 Way ReceptaclePart No. T-E-15-400

6 Way ReceptaclePart No. T-E-15-600Nose Box Adaptor Plate

Multiple mounting holes allow for easy installation.Part No. T-E-15-770

104

Zinc Die Cast 6 Way PlugLess spring guardPart No. T-E-15-610

Zinc Die Cast 6 Way PlugWith spring guardPart No. T-E-15-630

ELECTRICAL PLUGS AND RECEPTACLES

ISO 3731 ABS ReceptacleSanctioned by the Truck Manufacturers Association(T.M.A.) and the truck Trailer Manufacturers Association(T.T.M.A.) as the optional and separate ABS connector.Currently extensively used in Europe as the ABSconnector.Built to specifications per the International StandardsOrganization. (ISO)For applications requiring a separate ABS power andwarning light, such as on triple combination vehicles.

Single Pole PlugWith Strain ReliefSpringZinc Die Cast4 Gauge maximumCopper battery lug toinsure contactPart No. T-E-15-335

Dual Pole PlugPart No. T-E-15-336

Grote Ultra-Pin Receptacles2 & 3 Hole Mount

• Die cast zinc• Barrel slanted to drain moisture• Mounting holes slotted for universal fit• Floating pins for easy alignment• Kit contains retrofit plug-in

terminal kit consisting of9 terminals and 9 boots

• Weather-tight

2 Hole MountWith terminal kit Part No. T-E-GR87270Receptacle only Part No. T-E-GR87250

3 Hole MountWith terminal kit Part No. T-E-GR87240Receptacle only Part No. T-E-GR87220

Door HingeRepair KitDoor is diecast zinc

Solid brass pinKit contains

hinge pin, doorand spring

Part No. T-E-GR99680

Socket Breakerw/o breakers

Part No. T-E-16-860

7-Way Socketw/ring terminal

Part No. T-E-16-822

7-Way Receptaclew/QCS bullets & lock

Part No. T-E-16-826

Single PoleReceptacleZinc Die CastCopper batterylug to insurecontactStainlesshinge pinand springPart No. T-E-15-320

Dual PolePart No. T-E-15-326

Single Deep Nose Box

Part No. T-E-16-775

Dual Deep Nose BoxPart No. T-E-16-777

105

Truck-Lite 7 Way Receptacle• Made of GE Noryl - tough, nonconductive,

corrosion-resistant• Cadmium plated

floating brass pins• For use with ring

type terminals• Direct wired ground• Circuits identified by

both color codesand embossing

Standard 7 Way Body,Solid Pins:Part No. T-E-TL50860Standard 7 Way Body, Split Pins:Part No. T-E-TL50861Receptacle With 20A Circuit Breakers, Solid Pins:Part No. T-E-TL50864Receptacle w/15 amp circuit breakers, split pinsPart No. T-E-TL50863Receptacle With 20A Circuit Breakers, Split Pins:Part No. T-E-TL50865Receptacle w/threaded stacking studs, solid pinsPart No. T-E-TL50866Receptacle With Threaded stacking Studs, Split Pins:Part No. T-E-TL50867

Truck-Lite Flush Mount 7 Way Receptacle• Made of GE Noryl - tough,

nonconductive,corrosion-resistant

• Cadmium platedfloating brass pins

• For use with ringtype terminals

• Direct wired ground• Circuits identified

by both color codesand embossing

Standard 7 Way Receptacle, 2 Hole Flange, SplitPins:Part No. T-E-TL50869

Truck-Lite Nose Box• Made of foam polycarbonate• Chemical resistant, virtually indestructible• Internal electrical contacts are sealed to

eliminate corrosion• Available with or without circuit breakers• Main cable hookup

terminals arecolor identified

Nose Box WithoutCircuit Breakers:Part No. T-E-TL50805Nose Box With15A Circuit Breakers:Part No. T-E-TL50806Parts:Cap latch for7-Way Receptacle:Part No. T-E-TL50808Cover:Part No. T-E-TL50809

Surface Mounting Adaptor Boxes• Made of Noryl to allow surface mount of large

receptacles• Molded-in brass inserts for receptacle mounting• Available in deep (2" inside depth) or shallow

(1.25" inside depth)• Bottom entry or back entry versions

Shallow Adaptor Box,Bottom Access:Part No. T-E-TL50880Deep Adaptor Box,Bottom Access:Part No. T-E-TL50882Deep Adaptor Box,Back Access:Part No. T-E-TL50883

Cover Service Kit• 4 piece service kit for

all receptacles• Noryl cover,

steel hinge pin,stainless steelspring andshaft retainer

Part No. T-E-TL50875

Mounting holes on4.50" centers

Housing4.38"H X 5.12"

4.130"Centers6.19"

5.760"

4.88"

ELECTRICAL PLUGS AND RECEPTACLES

2.96" Centers