Electrical Components from Inter-Global · lamps fc8t9(22w)g10q xx xx fc12t9(32w) x f8t5 x xx x x x f13t5 x f14t8 x xx x x f15t8 xxxxx xxx x x f17t8 xx x xx x f18t8 xx x xx x f20t8

from Inter-Globalfrom Inter-Global

Electrical Components

ELECTRICAL COMPONENTS TABLE OF CONTENTS

Fluorescent Ballasts Page #

Lamp/Ballast Cross Reference .................................................................................... A1-A2Magnetic Ballasts ...................................................................................................... A3-A8Electronic Ballasts .................................................................................................... A8-A19Nema/ALA Matrix .................................................................................................. A20-A22Warranties .............................................................................................................. A21-A24

Sockets Page #

Ordering Guide............................................................................................................ B1GU24 Base Lampholders ............................................................................................ B2-B5Medium Base Lampholders & Brackets ........................................................................ B6-B14Mogul Base Lampholders .......................................................................................... B15-B16E-27 Medium Base Lampholders .................................................................................. B17Bayonet Lampholders .................................................................................................. B18Halogen Lampholders .................................................................................................. B18

Photocells & Receptacles Page #

Convenience Outlets .................................................................................................... C1Dusk To Dawn Switches .............................................................................................. C1-C2

LAMPS

CFT5W/G23 X X X

CFT7W/G23 X X X X X

CFT9W/G23 X X X X X X X

CFT13W/GX23 X X X X X X X X X

CFQ13W/GX23 X

CFQ13W/GX23 X X X X X X X X

CFQ22W/GX32d X

CFQ28W/GX32d X

FT18W/2G11 X X X

CFT5W/2G7 X

CFT7W/2G7 X

CFT9W/2G7 X

CFT13W/2GX7 X X X

CFTR13W/GX24q X

CFTR18W/GX24q X X X

CFTR26W/GX24q X X

CFTR32W/G24q X X X

CFM18W/2G10 X

CFQ13W/G24q X X X

CFQ18W/G24q X X X

CFQ26W/G24q X X X

CFQ32W/G24q X

IG8

OR

IG8

OP

IG9

O

IG9

OP

IG13

OP

IG13

OS

IG22O

P

IG28

0P

IG12O

22O

IG12O

22O

B

IG13

OSN

F

IG13

CP

IG9

CP

IG9

C

IG13

C

IG13

ML

PS2/80

9M

L120

PS2/813

ML1

20

PS2/83

2EL120

IG5

13

ELS

IG13

20

ELSXH

IG13

20

ELSX

IG25

32ELSX

IG213

20

ELSX

IG226

32ELS

X

COMPACT FLUORESCENT LAMP/BALLAST CROSS REFERENCE

MAGNETIC FLUORESCENT BALLAST ELECTRONIC FLUORESCENT BALLAST

Our LAMP/BALLAST CROSS REFERENCE helps customers identify which Inter-Global ballast operates which specific lamps.

A1

X=

For more information contact our sales department at 1-800-325-7364 or visit www.interglobal-inc.com 1209.1Specifications subject to change without notice. Printed in U.S.A. © 2013 Inter-Global Inc.

LINEAR FLUORESCENT LAMP/BALLAST CROSS REFERENCE

LAMPS

FC8T9(22W)G10q X X X X

FC12T9(32W) X

F8T5 X X X X X X

F13T5 X

F14T8 X X X X X

F15T8 X X X X X X X X X X

F17T8 X X X X X X

F18T8 X X X X X X

F20T8 X X X

F21T8 X

F25T8 X X X X

F28T8 X

F30T8 X X X

F32T8 X X X

F40T8 X X

F40T10 X X

F14T12 X X X X

F15T12 X X X X X

F20T12 X X X X X X X X X

F25T12 X X

F30T12 X X

F40T12 X X

IG8

OR

IG8

O

IG8

OP

IG13

O2

2O

IG9

C

IG9

CP

IG13

O2

2OB

IG15

20

IG13

CW

HB

IG22O

N1

2OP

IG5

13

ELS

IG13

20

EL

IG13

20

ELT9

IG13

20

ELSX

IG13

20

ELSXH

IG13

0ELS

X

IG23

0ELSX

IG25

32ELS

X

IG213

20

ELSX

IG2143

2ELT8

Our LAMP/BALLAST CROSS REFERENCE helps customers identify which Inter-Global ballast operates which specific lamps.

A2

MAGNETIC FLUORESCENT BALLAST ELECTRONIC FLUORESCENT BALLAST

X=


A3

Lamp Data Part # Circuit Electrical Data Physical Data CertificationLine Minimum

Current Input Starting Sound Case Std.Watts Model# Volts Hz (Amps) (Watts) Temp Rating Style Pkg Weight

8 F8T5 bulb ◊ IG80 120 60 0.150 10.4 32˚F A 1 100 28lbs. UL-CUL

F8T5 bulb8&9 CFT9W/G23 ◊ IG80R 120 60 0.150 10.2 32˚F A 1 100 28lbs. UR-CUR

F8T58&9 CFT9W/G23 *◊ IG80P 120 60 0.150 10.4 32˚F A 1 100 28lbs. UL-CUL

CFT7W/G23DULUX7

7&9 F7TT IG90 120 60 0.175 10.4 7W-5˚F/9W25˚F A 1A 100 28lbs. UR-CURF7BX

CFT9W/G23

CFT7W/G23CFT9W/G23DULUX9

7&9 F9TT *IG90P 120 60 0.175 10.4 7W-5˚F/9W25˚F A 1A 100 37lbs. UL-CULF9DTTF9BX

CFT13W/GX23CFQ13W/GX23

13 F13TT *IG130P 120 60 0.300 13.6 32˚F A 1C 50 28lbs. UL-CULF13DTTF13BX

CFT13W/GX2313 CFQ13W/GX23 ◊ IG130S 120 60 0.300 15 32˚F A 1B 50 33lbs. UR-CUR

22 PL22 *◊ IG220P 120 60 0.350 22 32˚F A 1D 100 57lbs. UL-CUL

28 PL28 *◊ IG280P 120 60 0.560 29 32˚F A 1E 50 46lbs. UL-CUL

* Ballast Class P ◊ Non-stocked, Special Order, Call for detailsNOTE: All Ballasts Type 1, Outdoor

OPEN CORE & COIL BALLAST SINGLE LAMP

• Contains no PCBs • Product Specifications

listed below

CASESTYLES A B C D E

1 2 11/16” 2 3/16” 1/2” 1 13/32” 1 11/16”1A 2 1/2” 2“ 9/16“ 1 13/32“ 1 11/16”1B 2 1/2” 2“ 21/32“ 1 13/32“ 1 11/16”1C 2 9/16” 2“ 27/32“ 1 13/32“ 1 11/16”1D 2 11/16“ 2 13/32“ 3/4“ 1 17/32“ 1 31/32”1E 2 7/8“ 2 9/16“ 1 1/10“ 1 21/32“ 1 31/32”

15” LEAD LENGTHS FOR STOCKED BALLASTS. CUSTOM LEAD LENGTHS AVAILABLE. CALL FOR DETAILS.

BALLASTBLACK

BLACK

WHITE

LAMP

STARTER

LINE

For warranty information refer to Inter-Global’s BALLAST LIMITED WARRANTY in the back of the Ballast section of this catalog.


A4

CASESTYLES A B C

3 11/16” 1 21/32” 23A 21/32” 1 13/32” 1 11/16”

OPEN CORE & COIL BALLAST SINGLE LAMP WITHOUT BRACKET



CFT13W/GX2313 CFQ13W/GX23 ◊ IG120-220 120 60 0.260 15 32˚F A 3 100 66lbs. UR-CUR

CFT13W/GX2313 CFQ13W/GX23 *◊ IG120-220B 120 60 0.260 15 32˚F A 3 100 66lbs. UR-CUR

CFT13W/GX2313 CFQ13W/GX23 ◊ IG130SNF 120 60 0.30 15 32˚F A 3A 50 33lbs. UR-CUR

F15T8 120 60 0.26 15.4 32˚F A 3 100 55lbs. UR-CUR15,18,20 F18T8 ◊ IG130-220 120 60 0.23 14.5 32˚F A 3 100 55lbs. UR-CUR

F20T12 120 60 0.22 15.9 32˚F A 3 100 55lbs. UR-CUR

F15T8 120 60 0.26 15.4 32˚F A 3 100 55lbs. UR-CUR15,18,20 F18T8 *◊ IG130-220B 120 60 0.23 14.5 32˚F A 3 100 55lbs. UR-CUR

F20T12 120 60 0.22 15.9 32˚F A 3 100 55lbs. UR-CUR

• Contains no PCBs• Product Specifications listed below

CUSTOM LEAD LENGTHS AVAILABLE. CALL FOR DETAILS.

BALLASTBLACK

BLACK

WHITE

LAMP

STARTER

LINE

* Class B Insulation ◊ Non-stocked, Special Order, Call for details

NOTE: All Ballasts Type 1, Outdoor



CASESTYLES A B C D E F

1 - - 1 3/16” 1 7/16” 2” 2 3/8”2 3 5/64” 2 9/16” 1 1/4” 1 47/64” 2 47/64” 3 5/64”

A5

ENCAPSULATED CORE & COIL BALLAST SINGLE LAMP



CFT13W/GX2313 CFQ13W/G23-2 *IG13CPWH 120 60 0.300 16 32˚F A 2 50 32lbs. UL-CUL

F14T8F14T12

14,15 F15T817,20 F15T12 IG15-20 120 60 0.320 14-20 32˚F A 2 50 32lbs. UL-CUL

F17T8F20T12

F14T1214,15, F14T818,20 F15T8 ◊ IG13CWHB 120 60 0.300 15 32˚F A 2 50 30lbs. UL-CUL

F18T8F20T12

CFT5W/G235,7, CFT7W/G23 *IG9CP 120 60 0.150 10.2 32˚F A 2 50 30lbs. UL-CUL8,9 CFT9W/G23

F8T5

CFT5W/G235,7 CFT7W/G23 IG9C 120 60 0.190 10.2 32˚F A 1 50 30lbs. UR8,9 CFT9W/G23 F8T5

CFT13W/GX2313 CFQ13W/G23-2 IG13C 120 60 0.350 16.0 32˚F A 2 50 33lbs. UR-CUR

• Contains no PCBs• Product Specifications listed below

15” LEAD LENGTHS FOR STOCKED BALLASTS. CUSTOM LEAD LENGTHS AVAILABLE. CALL FOR DETAILS.

BALLASTBLACK

BLACK

WHITE

LAMP

STARTER

LINE

* Ballast Class P ◊ Non-stocked, Special Order, Call for details

NOTE: All Ballasts Type 1, Outdoor



A6

IG220N120P 2 Lamp Ballast

Catalog Circuit Input Type Power Ballast Input SoundNumber Volts Wattage Number Factor Factor Current Rating

IG220N-120P 120 36 MAG. N .70 .75 A

LINEAR FLUORESCENT BALLAST

• Automatic reset able thermal disconnect• Standard leads 105˚C 18AWG wire (customer specified lengths)• Normal Power Factor• Suitable for (2) F15T8 15W, (2) F15T12 15W, or

(2) F20T12 20W lamps• Contains no PCBs

UL and CUL listed

LAMP

LAMP

REDRED

BLUEBLUE

YELLOWYELLOW

BLACKWHITE

LINE

BALLAST

Lamps must be mountedWithin 1/2" of grounded

metal reflector



IG13 Ballast

Wattage Circuit Catalog Type Power Ballast Input Sound Min. StartVolts Number Factor Factor Current Rating Temp

13 120 IG13ML-120 MAG. 0.67 (NPF) 85.1 0.30 A 32˚F

BALLAST SINGLE LAMP

• A reset able thermal disconnect from Texas Instruments• Standard lead length 13” 105˚C 18AWG wire.• Suitable for PLC Quad 13W lamp.• Contains no PCBs

UL and CUL listed

A7



A8

CFT5W/G23 7CFT7W/G23 **PS2/809ML-120 120 MAGNETIC 0.20 .864 7 32˚F White A UL(IFFX), CUL(IFFX7)CFT9W/G23 10

CFT13W/GX23 **PS2/813ML-120CFQ13W/GX23 •PS213ML-120 120 MAGNETIC 0.30 .851 8 32˚F Black B UL(IFFX), CUL(IFFX7)

CFQ26W/G24 106.5CFQ32W/G24

PS2/832EL-120 120 ELECTRONIC 0.45 .920104.8

0˚F Orange C UR(IFFX2), CUR(IFFX8)

POWERSOCKET

• Operating Voltage: 120 VAC ± 10%• Frequency: 60Hz (Electronic 50/60Hz)• Protection: Class P Thermal Protection• Over Current: Fuse (Electronic)

• Min. Starting Temp: 0˚F (-17.78˚C)* 32˚F Min. Starting Temp

• Max. Case Temp: 158˚F (75˚C)• FCC, 47 CFR, Part 18 Consumer Limits (Electronic)

• Power Factor: Normal (MH Models - High)• Lamp Current Crest Factor: <1.7 (Electronic)• End of Lamp Life Protection (Electronic)

• Mounting bracket for Powersocket• Made of steel• Available in white only• FIts all Powersocket models• Solves mounting issues

The Powersocket™ was designed to meet the need of fixturemanufacturers to build competitive compact fluorescent fixtures.Making a high quality, compact fluorescent fixture is no moredifficult or time consuming than building an incandescent fixture.

Suitable for one CFT5W/G23, CFT7W/G23, CFT9W/G23, CFT13W/GX23,CFQ13W/GX23, CFQ26W/G24*, or CFTR32W/G24* lampClass A Sound RatingMagnetic and Electronic Models AvailableSmall compact size

Electronic models are more efficient compared to standard magneticballasts, have end of life lamp protection, and eliminate strobingContains No PCBsRapid Start (Electronic)

Features & Benefits

Lamp Catalog Line Type Line Ballast THD Min Start Color Case ULNumber Volts Current Factor Percent Temp Code Size

8 Series

SPECIFICATIONS

M002PT

** High Power Factor available as special order. • Leads extend from side

2”(5

1mm

)

2.24

”(5

7mm

)

1.85

”(4

7mm

)

1.69

”(4

3mm

)

2.36

”(6

0mm

)

2.69” (68mm)

2.69” (68mm)2.69” (68mm)

1.96

”(5

0mm

)

1.77

”(4

5mm

)

1.69

”(4

3mm

)

1.38

”(3

5mm

)

Leads extended from sideLeads extended

through Bottom Hole

2”(5

1mm

)

2.24

”(5

7mm

)

1.85

”(4

7mm

)

1.69

”(4

3mm

)

2.36

”(6

0mm

)

2.69” (68mm)

2.69” (68mm)2.69” (68mm)

1.96

”(5

0mm

)

1.77

”(4

5mm

)

1.69

”(4

3mm

)

1.38

”(3

5mm

)


through Bottom Hole

US Patent DES 415,103

For warranty information refer to Inter-Global’s BALLAST LIMITED WARRANTYin the back of the Ballast section of this catalog.


2”(5

1mm

)

2.24

”(5

7mm

)

1.85

”(4

7mm

)

1.69

”(4

3mm

)

2.36

”(6

0mm

)

2.69” (68mm)

2.69” (68mm)2.69” (68mm)

1.96

”(5

0mm

)

1.77

”(4

5mm

)

1.69

”(4

3mm

)

1.38

”(3

5mm

)


through Bottom Hole

• One Lamp• Multi-Watt• Small Case Size• Lightweight• Versatile• Energy Saving

• Operating Voltage: 120 VAC ± 10%• Frequency: 50/60Hz• Protection: Class P Inherent Thermal Protection

• Regulatory Approvals: UL, CUL Listed• Over Current: Fuse• Min. Starting Temp: 0˚F (-17.78˚C)

* 32˚F Min. Starting Temp

• Max. Case Temp: 158˚F (75˚C)• FCC, 47 CFR, Part 18 Consumer Limits• Type 1 Outdoor, Normal Power Factor

ELECTRONIC BALLAST

Wide lamp versatility, suitable for one F8T5, F13T5*, CFT5W/2G7,CFT7W/2G7, or CFT9W/2G7 lamp

Class A Sound Rating

End of Lamp Life Protection

More efficient compared to standard magnetic ballasts

Lead wires do not interfere with mounting holes

Contains No PCBs

Eliminates strobing

Thermal potting

Metal enclosure

Rapid Start

Features & Benefits

120 F8T5 0.12 7.4 0.53 1.4 0.55 117.5 0˚F

120 F13T5 0.16 10.6 0.56 1.5 0.65 101.5 32˚F

120 CFT5W/2G7 0.9 5.2 0.50 1.6 0.84 136.1 0˚F

120 CFT7W/2G7 0.11 6.7 0.52 1.5 0.82 123.2 0˚F

120 CFT9W/2G7 0.12 7.5 0.53 1.5 0.81 117.4 0˚F

Line Lamp Line Input Power Crest Ballast THD Min StartVoltage Type Current Power Factor Factor Factor Percent Temp

IG513ELS

SPECIFICATIONS

A9

0.195"(5mm) 0.195"

(5mm)1.04

"(2

6mm

)



A10

ELECTRONIC BALLAST




SPECIFICATIONS

Wide lamp versatility, suitable for one F14T8, F14T12, F15T8, F15T12, F17T8, F18T8, F20T8, F20T12, or FC8T9(22W)G10q lamp.Optional pre-wired plug for CIRCLINE lamps (IG13-20EL/T9)Class A Sound RatingMore efficient compared to standard magnetic ballastsLead wires do not interfere with mounting holes

Contains No PCBsEliminates strobingThermal pottingMetal enclosureRapid Start

Features & Benefits

IG1320EL

1.58

"(4

0mm

)

2.22" (56mm)

0.19"(5mm) 0.19"

(5mm)

120 F14T8 0.15 10 0.55 1.7 0.77 101.1 O˚F120 F14T12 0.15 10 0.55 1.7 0.74 105.6 0˚F120 F15T8 0.16 11 0.56 1.7 0.83 96.3 0˚F120 F15T12 0.16 10 0.55 1.7 0.78 97.1 0˚F120 F17T8 0.19 13 0.57 1.63 0.80 92.5 0˚F120 F18T8 0.18 12 0.57 1.6 0.67 94.7 0˚F120 F20T12 0.18 12 0.57 1.62 0.64 94.6 0˚F120 FC8T9 0.20 12.7 0.53 1.38 0.56 93.2 0˚F



IG1320EL/T9See page A11



ELECTRONIC BALLAST




SPECIFICATIONS

Suitable for one FC8T9 CIRCLINE 22 WATT lamp.




Contains No PCBsEliminates strobingThermal pottingMetal enclosureRapid Start

Features & Benefits

IG1320EL/T9

PLUG FOR CIRCLINE LAMPS

0.19"(5mm)

0.19"(5mm)

3.107" (79mm)

1.74

5"(4

4mm

)

120 FC8T9 0.2 12.7 .531 1.38 0.56 93.2 0˚F


• One Lamp• Pre-Wired With Plug• Small Case Size• Lightweight

A11




Wide lamp versatility, suitable for one CFQ13W/G24q, CFT13W/2GX7,CFM13W/G24q, F14T8, F14T12, F15T8, F15T12, F17T8, F18T8, CFTR18W/GX24,CFQ18W/G24q, FT18W/2G11, F20T8, F20T12, or FC8T9(22W)G10q lampClass A Sound RatingEnd of Lamp Life ProtectionMore efficient compared to standard magnetic ballastsLead wires do not interfere with mounting holes

Contains No PCBs

Eliminates strobing

Thermal potting

Metal enclosure

Rapid Start

Features & Benefits

IG1320ELSX

1.87

"(4

7mm

)

3.095" (79mm)

0.19"(5mm) 0.19"

(5mm)

120 CFQ13W/G24q 0.19 13.4 0.57 1.57 0.98 113.7 0˚F120 CFT13W/2GX7 0.16 10.2 0.54 1.52 0.70 124.1 0˚F120 CFQ18W/G24q 0.20 14.7 0.57 1.55 0.83 112.3 0˚F120 F14T8 0.15 10 0.55 1.7 0.77 126 O˚F120 F14T12 0.15 10 0.55 1.7 0.74 131 0˚F120 F15T8 0.16 11 0.56 1.7 0.83 118.5 0˚F120 F15T12 0.16 10 0.55 1.7 0.78 124.1 0˚F120 F17T8 0.19 13 0.57 1.5 0.80 113.2 0˚F120 F18T8 0.18 12 0.57 1.6 0.67 112.6 0˚F120 F20T12 0.18 12 0.57 1.62 0.64 116.5 0˚F





SPECIFICATIONS

A12

ELECTRONIC BALLAST


ENERGY STARPARTNER

SCAN THE QR CODE TO THE LEFT TO ACCESS THE ENERGY STAR SUB COMPONENT DATABASE.


ELECTRONIC BALLAST

A13

• One Lamp• Multi-Watt• Small Case Size• High Heat• Lightweight• Energy Saving

Wide lamp versatility, suitable for one CFQ13W/G24q, CFT13W/2GX7,CFM13W/G24q, F14T8, F14T12, F15T8, F15T12, F17T8, F18T8, CFTR18W/GX24,CFQ18W/G24q, FT18W/2G11, F20T8, F20T12, or FC8T9(22W)G10q lampClass A Sound RatingEnd of Lamp Life ProtectionMore efficient compared to standard magnetic ballastsLead wires do not interfere with mounting holes

Contains No PCBs

Eliminates strobing

Thermal potting

Metal enclosure

Rapid Start

Features & Benefits

IG1320ELSXH

0.19"(5mm) 0.19"

(5mm)

3.095" (79mm)

1.2"

(30m

m)

1.87

"(4

7mm

)




SPECIFICATIONS

120 CFQ13W/G24q 0.19 13.2 0.56 1.58 0.98 113.7 0˚F120 CFT13W/2GX7 0.16 10.2 0.54 1.52 0.70 124.1 0˚F120 CFQ18W/G24q 0.20 14.7 0.57 1.55 0.83 112.3 0˚F120 F14T8 0.15 10 0.55 1.7 0.77 126 O˚F120 F14T12 0.15 10 0.55 1.7 0.74 131 0˚F120 F15T8 0.16 11 0.56 1.7 0.83 118.5 0˚F120 F15T12 0.16 10 0.55 1.7 0.78 124.1 0˚F120 F17T8 0.19 12.8 0.56 1.48 0.77 113.2 0˚F120 F18T8 0.18 12 0.57 1.6 0.67 112.6 0˚F120 F20T12 0.18 12 0.57 1.62 0.64 116.5 0˚F


ENERGY STARPARTNER

For warranty information refer to Inter-Global’s BALLAST LIMITED WARRANTY in the back of the Ballast section of this catalog.SCAN THE QR CODE TO THE LEFT TO ACCESS THE ENERGY STAR SUB COMPONENT DATABASE.


A14

ELECTRONIC BALLAST

SPECIFICATIONS• Operating Voltage: 120 VAC ± 10%• Frequency: 50/60Hz• Protection: Class P Inherent Thermal Protection



• Two Lamp• Multi-Watt• Small Case Size• High Heat• Lightweight• Energy Saving

Wide lamp versatility, suitable for two F15T8, F17T8, F20T12,CFQ13W/G24q, CFTR13W/GX24q, CFT13W/2GX7, CFQ18W/G24q,CFTR18W/GX24q, FT18W/2G11, or CFM18W/2G10 lamps




Contains No PCBs

Eliminates strobing

Thermal potting

Metal enclosure

Rapid Start

Features & Benefits

IG21320ELSX

Weight: 9.6 oz. Case Quantity: 40pcs Case Weight: 32 lbs Standard Lead Length: black/white-12” blue/red-27” yellow-27”

1.10

"(2

8mm

)

1.96

"(5

0mm

)

0.19

"(5

mm

)

1.89

"(4

8mm

)

1.5"

(38m

m)

0.19" (5mm) dia.

3.775" (96mm)

5.07" (129mm)

120 F15T8 0.323 20.3 0.52 1.7 0.58 114 0˚F120 F17T8 0.446 21.3 0.52 1.5 0.56 114.2 0˚F120 F20T12 0.338 22.2 0.55 1.7 0.50 114.2 0˚F120 CFQ13W/G24q 0.40 23.2 0.53 1.48 0.83 114.4 0˚F120 CFTR13W/GX24q 0.38 23.9 0.52 1.6 0.84 114.3 0˚F120 CFT13W/2GX7 0.30 17.4 0.50 1.49 0.66 114.5 0˚F120 CFQ18W/G24q 0.42 26.7 0.545 1.44 0.76 115.4 0˚F120 CFTR18W/GX24q 0.44 28.1 0.53 1.5 0.75 114.9 0˚F120 FT18W/2G11 0.35 21.4 0.508 1.7 0.58 115 0˚F120 CFM18W/2G10 0.32 20.0 0.50 1.7 0.56 115.3 0˚F


ENERGY STARPARTNER



A15

ELECTRONIC BALLAST


• Regulatory Approvals: UL, CUL Listed• Min. Starting Temp: 0˚F (-17.78˚C)• Max. Case Temp: 194˚F (90˚C)

• Over Current: Fuse• FCC, 47 CFR, Part 18 Consumer Limits• Type 1 Outdoor, Normal Power Factor

• One Lamp• Multi-Watt• Small Case Size• High Heat• Lightweight• Energy Saving

Wide lamp versatility, suitable for one F25T8, CFQ26W/G24q,CFTR26W/GX24q, or CFTR32W/GX24q lamp




Contains No PCBs

Eliminates strobing

Thermal potting

Metal enclosure

Rapid Start

Features & Benefits

IG2532ELSX

SPECIFICATIONS

4.72”(120mm)

4.33”(110mm)

Weight: 6.7oz. Case Quantity: 50pcs Case Weight: 25.5 lbs Standard Lead Length: black/white-12” blue/red-27”

.68”

(17.5mm)

1.06

”(2

7mm

)

0.19

"(5

mm

)

0.19

"(5

mm

)

1.57

"(4

0mm

)

3.95" (100mm)

120 F25T8 0.34 22.0 0.54 1.60 0.80 104.6 0˚F

120 CFQ26W/G24q 0.29 22.0 0.555 1.58 0.83 107.2 0˚F

120 CFTR26W/GX24q 0.33 21.0 0.553 1.66 0.74 106.5 0˚F

120 CFTR32W/GX24q 0.36 23.0 0.563 1.57 0.69 104.5 0˚F


ENERGY STARPARTNER



A16


• Regulatory Approvals: UL, CUL Listed• Min. Starting Temp: 0˚F (-17.78˚C)• Max. Case Temp: 194˚F (90˚C)

• Over Current: Fuse• FCC, 47 CFR, Part 18 Consumer Limits• Type 1 Outdoor, Normal Power Factor

• Two Lamp• Multi-Watt• Small Case Size• High Heat• Lightweight• Energy Saving

Wide lamp versatility, suitable for two CFQ26W/G24q,CFTR26W/GX24q, or CFTR32W/GX24q lamps





Contains No PCBs

Eliminates strobing

Thermal potting

Metal enclosure

Rapid Start

Features & Benefits

IG22632ELSX

SPECIFICATIONS2.25”

(57mm)

Weight: 14 oz. Case Quantity: 40pcs Case Weight: 29.5 lbs Standard Lead Length: black/white-12” blue/red/yellow-12”

4.35" (110mm)

5.23" (133mm)

0.19

"(5

mm

)

2.45

"(6

2mm

)

1.06

"(2

7mm

)

120 CFQ26W/G24q 0.57 44.5 0.513 1.46 0.86 119.6 0˚F

120 CFTR26W/GX24q 0.56 44.7 0.513 1.49 0.77 119.9 0˚F

120 CFTR32W/GX24q 0.62 48.2 0.521 1.43 0.69 118.9 0˚F


ELECTRONIC BALLAST

ENERGY STARPARTNER



A17

ELECTRONIC BALLAST


• Regulatory Approvals: UL, CUL Listed• Min. Starting Temp: 0˚F (-17.78˚C)

* 32˚F Min. Starting Temp

• Max. Case Temp: 158˚F (75˚C)• Over Current: Fuse• Type 1 Outdoor, Normal Power Factor


Wide lamp versatility, suitable for one F25T8, F25T12, F30T8,F30T12, *FC12T9(32W), *F32T8, *F34T12, *F40T8, *F40T10,or *F40T12 lamp





Contains No PCBs

Eliminates strobing

Thermal potting

Metal enclosure

Rapid Start

Features & Benefits

IG130ELSX

SPECIFICATIONS

0.2"

(5m

m)

1.87

"(4

7mm

)

1.2"

(30m

m)

120 F25T8 0.45 22.7 0.50 1.39 0.90 117.9 0˚F120 F25T12 0.45 26.8 0.50 1.54 1.01 116.2 0˚F120 F30T8 0.45 27.3 0.50 1.33 0.90 117.4 0˚F120 F30T12 0.45 27.6 0.50 1.50 0.91 117.3 0˚F120 F32T8 0.49 27.8 0.53 1.32 0.80 118.8 32˚F120 F34T12 0.46 27.9 0.50 1.50 0.81 117.5 32˚F120 F40T12 0.56 28.0 0.50 1.40 0.73 118.4 32˚F


ENERGY STARPARTNER



A18

ELECTRONIC BALLAST



* 32˚F Min. Operating Temp


• Two Lamp• Multi-Watt• Small Case Size• Lightweight• Versatile• Energy Saving

Wide lamp versatility, suitable for two F25T8, F25T12, F30T8,F30T12, *F32T8, *F34T12, *F40T8, *F40T10, or *F40T12 lamps





Contains No PCBs

Eliminates strobing

Thermal potting

Metal enclosure

Rapid Start

Features & Benefits

IG230ELSX

SPECIFICATIONS

0.19" (5mm) dia.

1.91

5"(4

9mm

)

0.19

"(5

mm

)

1.17

5"(3

0mm

)

120 F25T8 0.70 50.6 0.507 1.39 1.0 119.2 0˚F120 F25T12 0.58 36.8 0.53 1.50 0.74 119.5 0˚F120 F30T8 0.70 46.6 0.55 1.50 0.78 119.1 0˚F120 F30T12 0.63 41.4 0.54 1.40 0.70 119.7 0˚F120 F32T8 0.80 61.5 0.53 1.40 0.90 117.3 32˚F120 F34T12 0.66 43.6 0.55 1.40 0.66 119.3 32˚F


ENERGY STARPARTNER



A19

SPECIFICATIONS• Operating Voltage: 120 VAC• Frequency: 50/60Hz• Protection: Class P Inherent Thermal Protection



• One or Two Lamp• Multi-Watt• Energy Saving

Wide lamp versatility, suitable for one or two F14T8, F15T8, F17T8,F21T8, F25T8, F28T8, F30T8 or F32T8 lampsClass A Sound RatingMore efficient compared to standard magnetic ballasts

Contains No PCBsEliminates strobingThermal pottingMetal enclosureInstant Start

Features & Benefits

IG21432ELT8

1.22”

(31m

m)

1.77”

(45m

m)

9.57” (243.1mm)

black/white-24” red-50” blue-34”Weight: 20 oz. Case Quantity: 30pcs Case Weight: 38 lbs Standard Lead Length:

7.5" (191mm)

1.25

"(3

2mm

)

0.33

"(8

mm

)

1.91

"(4

9mm

)

120 1 X F14T8 0.23 17.46 0.63 1.49 0.79 115.1 0˚F120 2 X F14T8 0.30 23.02 0.64 1.51 0.57 111.8 0˚F120 1 X F15T8 0.26 20.16 0.64 1.49 0.79 111.8 0˚F120 2 X F15T8 0.35 26.97 0.63 1.53 0.70 113.0 0˚F120 1 X F17T8 0.30 23.20 0.64 1.49 0.92 111.0 0˚F120 2 X F17T8 0.43 32.43 0.63 1.55 0.78 114.1 0˚F120 1 X F21T8 0.38 28.88 0.63 1.50 0.88 112.9 0˚F120 2 X F21T8 0.50 37.64 0.62 1.57 0.77 114.3 0˚F120 1 X F25T8 0.41 30.74 0.63 1.49 0.89 113.3 0˚F120 2 X F25T8 0.58 43.24 0.62 1.60 0.78 113.9 0˚F120 1 X F28T8 0.44 33.03 0.63 1.49 0.91 113.9 0˚F120 2 X F28T8 0.64 47.77 0.62 1.59 0.79 113.3 0˚F120 1 X F30T8 0.41 30.60 0.63 1.50 0.77 113.7 0˚F120 2 X F30T8 0.59 43.98 0.62 1.59 0.66 113.7 0˚F120 1 X F32T8 0.49 32.5 0.50 1.54 0.94 114.1 0˚F120 2 X F32T8 0.76 52.5 0.55 1.63 0.79 111.5 0˚F


ELECTRONIC BALLAST

ENERGY STARPARTNER



A20

Ballast Model IG13-20ELSX IG13-20ELSX IG13-20ELSX IG13-20ELSX IG230ELSX IG230ELSX IG130ELSX IG130ELSX

Number of Lamps 1 1 1 1 2 2 1 1

Lamp Type CFQ13W/G24q CFQ18W/G24q CFT13W/2GX7 F17T8 F32T8 F25T8 F32T8 F25T8

Min. Initial 673 886 739 831 2315 1778 2345 1230Lamp Lumens

Min. Lumens 50 50 50 50 70 70 70 50Per Watt

Input Power 13.2 14.7 10.2 12.8 61.5 50.6 27.8 22.7(Watts)

Ballast 0.98 0.83 0.7 0.77 0.9 1.0 0.8 0.9Factor

Lamp Start 153 17 9.3 480 52 52 38 97Time (ms)

Power 0.563 0.569 0.54 0.563 0.53 0.507 0.53 0.5Factor

Lamp Current 1.58 1.55 1.52 1.48 1.4 1.39 1.32 1.39Crest Factor

Ballast Hot 2” 2” 2” 2” 1.7” 1.7” 3.5” 3.5”Spot Location

Max. Ballast 75 75 75 75 75 75 75 75Case Temp(˚C)

FCC Yes Yes Yes Yes Yes Yes Yes YesRequirements

Ballast 23.8 25.4 20.67 23.5 29.3 26.1 26.8 24.3Frequency(kHz)

Transient Yes Yes Yes Yes Yes Yes Yes YesProtection

End of Life Yes Yes Yes N/A N/A N/A N/A N/AProtection (EOL)

Max # of Lamps 1 1 1 N/A N/A N/A N/A N/AShutdown at EOL

Dimming No No No No No No No NoCapable

Safety Yes Yes Yes Yes Yes Yes Yes YesListing

Line Voltage Socket No No No No No No No NoStandard Design

NEMA (NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION)ALA (AMERICAN LIGHTING ASSOCIATION) Ballasts listed in this table meet the ballast-controlled performance requirements in the ENERGY STAR Program Requirements for ResidentialLight Fixtures, version 4.0. Data in this matrix is subject to change.

More information can be found at www.nema.org/lampballastmatrix/ballasts.html

NEMA/ALA BALLAST MATRIX


SCAN THE QR CODE TO THE RIGHT TO ACCESS THEENERGY STAR SUB COMPONENT DATABASE.

A21

Ballast Model IG213-20ELSX IG213-20ELSX IG213-20ELSX IG213-20ELSX IG25-32ELSX IG25-32ELSX IG25-32ELSX

Number of Lamps 2 2 2 2 1 1 1

Lamp Type CFQ13W/G24q CFQ18W/G24q CFT13W/2GX7 F17T8 CFQ26W/G24d CFTR26W/GX24q CFTR32W/GX24q

Min. Initial 693 1054 659 1141 1325 1419 2000Lamp Lumens

Min. Lumens 50 60 50 60 50 50 60Per Watt

Input Power 23 26.7 17.4 21.3 22 21 23(Watts)

Ballast 0.83 0.76 0.66 0.56 0.83 0.74 0.69Factor

Lamp Start 499 163 17 355 22 40 187Time (ms)

Power 0.53 0.545 0.5 0.52 0.555 0.553 0.563Factor

Lamp Current 1.48 1.44 1.49 1.48 1.58 1.66 1.57Crest Factor

Ballast Hot 0.65” 0.65” 0.65” 0.65” 3.3” 3.3” 3.3”Spot Location

Max. Ballast 90 90 90 90 90 90 90Case Temp(˚C)

FCC Yes Yes Yes Yes Yes Yes YesRequirements

Ballast 25 27 22 26 22 21 22Frequency(kHz)

Transient Yes Yes Yes Yes Yes Yes YesProtection

End of Life Yes Yes Yes N/A Yes Yes YesProtection (EOL)

Max # of Lamps 2 2 2 N/A 1 1 1Shutdown at EOL

Dimming No No No No No No NoCapable

Safety Yes Yes Yes Yes Yes Yes YesListing

Line Voltage Socket No No No No No No NoStandard Design

NEMA/ALA BALLAST MATRIX CONTINUED





Ballast Model IG226-32ELSX IG226-32ELSX IG226-32ELSX IG214-32ELT8 IG214-32ELT8

Number of Lamps 2 2 2 2 1

Lamp Type CFQ26W/G24d CFTR26W/GX24q CFTR32W/GX24q F32T8 F32T8

Min. Initial 1552 1742 2096 2326 2425Lamp Lumens

Min. Lumens 60 60 60 70 70Per Watt

Input Power 44.5 44.7 48.2 52.5 32.5(Watts)

Ballast 0.86 0.77 0.69 0.79 0.94Factor

Lamp Start 57 187 136 300 280Time (ms)

Power 0.513 0.513 0.521 0.55 0.5Factor

Lamp Current 1.46 1.51 1.43 1.7 1.7Crest Factor

Ballast Hot 2.7” 2.7” 2.7” 3.2” 3.2”Spot Location

Max. Ballast 90 90 90 75 75Case Temp(˚C)

FCC Yes Yes Yes Yes YesRequirements

Ballast 25 25 26 44.4 32.5Frequency(kHz)

Transient Yes Yes Yes Yes YesProtection

End of Life Yes Yes Yes N/A N/AProtection (EOL)

Max # of Lamps 2 2 2 N/A N/AShutdown at EOL

Dimming No No No No NoCapable

Safety Yes Yes Yes Yes YesListing

Line Voltage Socket No No No No NoStandard Design

NEMA/ALA BALLAST MATRIX CONTINUED

A22For more information contact our sales department at 1-800-325-7364 or visit www.interglobal-inc.com 1209.1

Specifications subject to change without notice. Printed in U.S.A. © 2013 Inter-Global Inc.




A23

Inter-Global warrants that its fluorescent ballast shall be free from defects in material and workmanship and will be of the designated kind and quality for the

assigned period listed below from the date of manufacture.

Inter-Global makes no warranty whatsoever with respect to any ballast not installed and operated in accordance with the current edition of the National Electrical

Code, the standards of safety of Underwriters Laboratories, the standards of the American National Standards Institute and specific instructions provided by Inter-

Global for installation and operation of the ballast.

If it appears within the said warranty period that any Inter-Global ballast does not meet the warranty specified above, the purchaser must give written notice of

their warranty claim and return the ballast, at the purchaser's expense to Inter-Global or an authorized sales representative in purchaser's geographic area.. Within

sixty (60) days of receipt, Inter-Global shall at its expense and option correct any defects by either repairing or replacing the defective part(s) or the ballast. This war-

ranty is not applicable to any ballast subjected to abnormal stresses, operating conditions and operating conditions including lamp mismatch applications.

TEMPERATURE ON BALLAST CASE SHOULD NOT EXCEED THE MAXIMUM TEMPERATURE SPECIFIED ABOVE . Inter-Global cannot be responsible for

non Inter-Global equipment which is attached to or used in conjunction with the ballast and all such equipment is expressly excluded from Inter-Global's warranty.

The foregoing warranty is exclusive of all other statutory written or oral warranties and no other warranties of any kind, statutory or otherwise, are given or here-

in expressed. INTER-GLOBAL HEREBY DISCLAIMS ANY IMPLIED STATUTORY WARRANTY OR IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE.

Under no circumstances whether as a result of breach of contract, breach of warranty, tort strict liability or otherwise, will Inter-Global or any distributor or sales

representative be liable for consequential, incidental, special or exemplary damages, including but not limited to loss of profits, loss of use or damage to any property

or equipment, cost of capital, cost of substitutes, products facilities or services, down time cost or claims of purchaser's customers.

The Liability of Inter-Global or any distributor or sales representative on all claims of any kind for any loss or damage arising out of, resulting from or concerning

any aspect of this limited warranty, from the ballast furnished, shall not exceed the price of the specific ballast which gives rise to the claims.

REPAIR OR REPLACEMENT FOR BALLAST UNDER WARRANTY

Step 1 Contact Inter-Global within 30 days of discovery to explain the nature of the defect:

BY MAIL - Inter-Global Warranties, 6333 Etzel Avenue, St. Louis, MO 63133-1998

BY PHONE - 1-800-325-7364

BY FAX - 314-721-6333

BY E-MAIL - [email protected]

Step 2 You may be instructed to send some or all of the units back for evaluation. In some cases a complete lighting fixture will be required for testing. You will

be given a Return Authorization (RGA) Number. This number must appear on all cartons, packaging slips, debit memos and other correspondence. No

merchandise will be accepted without a valid RGA number marking the shipment. The ballast must be returned freight prepaid-COLLECT

SHIPMENTS WILL BE REFUSED.

RETURN MERCHANDISE TO 6333 ETZEL AVE., ST. LOUIS, MO 63133-1998

Step 3 The returned ballast will be evaluated by Inter-Global to determine if it is covered under the Limited Warranty.

BALLAST UNDER WARRANTY - When all of the following conditions exist, the returned ballast will be considered under warranty

and will be repaired or replaced at the option of Inter-Global.

1. The ballast was manufactured less than the specific warranty period earlier than the date of return.

2. It is determined by Inter-Global that the ballast was installed and operated in accordance with the current edition of the National Electrical

Code, the standards for safety of Underwriter's Laboratories, Inc. the standards of the American National Standards Institute and the specific

inst ructions provided by Inter-Global for installation and operation of the ballast.

3. The ballast does not operate according to Inter-Global specifications, due to defects in material or workmanship.

4. The ballast manufacturing date code has not been altered or is not missing (DATE CODE - Each ballast is marked with a date code

in the form of a sticker or stamped into the case depending on the type of unit). The first two digits represent the year, and the next two digits represent

the month of the year of manufacture.

5. The ballast was not damaged due to physical abuse and was returned in adequate packaging to prevent damage to the ballast.

BALLAST NOT UNDER WARRANTY - Any ballast determined by Inter-Global not to be under warranty will be returned to the

customer (freight paid by customer), or destroyed, at the customer's option.

Part Number Warranted for this Period

IG9O 3 Years (maximum case temp. of 90°C)

IG9OP 3 Years (maximum case temp. of 90°C)

IG9CP 3 Years (maximum case temp. of 90°C)

PS2/809ML-120 3 Years (maximum case temp. of 75°C)


IG13CPWH 3 Years (maximum case temp. of 90°C)

PS2/813ML-120 3 Years (maximum case temp. of 75°C)

PS213ML-120 3 Years (maximum case temp. of 75°C)

IG13ML-120 3 Years (maximum case temp. of 90°C)

IG13MH-120 3 Years (maximum case temp. of 90°C)

IG15-20 3 Years (maximum case temp. of 90°C)


IG220N-120P 3 Years (maximum case temp. of 90°C)

BALLAST LIMITED WARRANTY

Part Number Warranted for this Period

IG5-13ELS 2 Years (maximum case temp. of 75°C)

IG13-20EL 2 Years (maximum case temp. of 75°C)

IG13-20EL/T9 2 Years (maximum case temp. of 75°C)

IG13-20ELSX 2 Years (maximum case temp. of 75°C)

IG13-20ELSXH 2 Years (maximum case temp. of 90°C)

IG130ELSX 2 Years (maximum case temp. of 75°C)




IG230ELSX 2 Years (maximum case temp. of 75°C)

PS2/832EL-120 2 Years (maximum case temp. of 75°C)

IG214-32ELT8 2 Years (maximum case temp. of 75°C)


ORDERING GUIDE

For Lampholders with SingleBrackets

For Harness Set Lampholders

For Lampholders with DoubleBrackets

Body Series NumberBracket Number

Description to include wire length, wire type, screwshell type if different thanaluminum (STD) dimensions for stripping leads.Ground Wire (“G” with ground, “O” without ground wire)Bracket Type

201 012 A G 10” 105˚ B&W PLST LDS STR 12.77mm

Number of LampholdersBody Series NumberBracket Number

Description to include wire length, wire type, screwshell type if different thanaluminum (STD) dimensions for stripping leads.Ground Wire (“G” with ground, “O” without ground wire)Bracket Type

2X 202 002 Q G 10” 105˚ B&W PLST LDS STR 12.77mm SKTS 6” C to C

Body Series NumberTop Bracket NumberTop Bracket Type

Description to include wire length, wire type, screwshell type if different thanaluminum (STD) dimensions for stripping leads.Ground Wire (“G” with ground, “O” without ground wire)Bottom Bracket TypeBottom Bracket Number

3WO 039 E 163 T G 8” 105˚ B&W PLST LDS STR 12.77mm

B1For more information contact our sales department at 1-800-325-7364 or visit www.interglobal-inc.com 1209.1


Part Number Dimensions Photo

GU26I

GU27F

◊ GU28C

GU28D

• Molded white phenolic GU24 base socket with threaded male, threadedfemale or rivet type brackets.

• Standard leads are 12” long, AWM 18 gauge 1050 plastic insulated wire.• Custom lead lengths and 1500 C sleeving available upon request.*• Custom lead configurations available upon request.*• Ground wire available upon request.*• Bracket types available are listed on pages B2-B5.• Standard packed 400 to a carton.UL CUL Listed, Suitable for Damp Locations 660W, 600V

B2

GU24 BASE LAMPHOLDERS

0.47”(12mm)

0.94”(24mm)

1.53”(39mm)

Series GU GU24 Lampholder

BRACKET TYPES FOR GU24 LAMPHOLDERS

0.472"(12mm)

1.551"(39.4mm) 1.535"

(39mm)

1.024"(26mm)

0.374"(9.5mm)

1.535"(39mm)1.181"

(30mm)

0.906"(23mm)

0.374"(9.5mm)

1.535"(39mm)

0.374"(9.5mm)

1.063"(27mm)

NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS

ASK ABOUTGU24 MODELS

GU24 MODELSAVAILABLE

CLEARPRISMATICAVAILABLE

*additional charges apply

◊ Non-stocked, Special Order, Call for details

NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS






GU28K

GU28KS

◊ GU28KN

GU36C

◊ GU36D

◊ GU37F


B3

1.102"(28mm)

1.114"(28.3mm)

1.535"(39mm)

1.417"(36mm)

0.374"(9.5mm)

1.535"(39mm)

1.102"(28mm)

1.114"(28.3mm)

1.441"(36.6mm)

1.535"(39mm)1.044"

(26.5mm)

1.575"(40mm)

1.457"(37mm)

1.417"(36mm)

2.476"(62.9mm)

0.374"(9.5mm)

1.535"(39mm)1.083"

(27.5mm)

1.449"(36.8mm)0.236"

(6mm)

0.413"(10.5mm)

0.161"(4.1mm)

0.402"(10.2mm)

◊ Non-stocked, Special Order, Call for details

NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS






GU46G

GU51H

◊ GU56C

◊ GU56D

◊ GU94L

B4


0.374"(9.5mm)

3.008"(76.4mm)

1.969"(50mm)

1.535"(39mm)

3.008"(76.4mm)

1.969"(50mm)

0.374"(9.5mm)

1.535"(39mm)

3.701"(94mm)

0.433"(11mm)

0.374"(9.5mm)

0.602"(15.3mm)

4.516"(114.7mm)

1.535"(39mm)

2.366"(60.1mm)

1.535"(39mm)

2"(50.8mm)

0.378"(9.6mm)

NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




◊ Non-stocked, Special Order, Call for detailsFor more information contact our sales department at 1-800-325-7364 or visit www.interglobal-inc.com 1209.1



GU101M

GU201A

GU205A

◊ GU305A


B5

1.535"(39mm)

0.937"(23.8mm)

1.535"(39mm)

1.150"(29.2mm)

0.244"(6.2mm)

2.102"(53.4mm)

0.374"(9.5mm)

2.260"(57.4mm)

1.535"(39mm)

0.386"(9.8mm)

1.535"(39mm)

3.996"(101.5mm)

0.382"(9.7mm)

0.433"(11mm)

4.764"(121mm)

3.291"(83.6mm)

1.339"(34mm)

NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




NOWIN STOCK

NEW

COMINGAUGUST 08

COMINGSOON

COMINGJUNE 08

ASK ABOUTT5 MODELS




◊ Non-stocked, Special Order, Call for detailsFor more information contact our sales department at 1-800-325-7364 or visit www.interglobal-inc.com 1209.1


B6

Series 301 Tapered Porcelain Lampholder

• Unglazed porcelain body on E26 medium base lampholder with threaded male,threaded female or rivet type brackets.

• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plastic insulated wire.(Bare copper ground wire available upon request.)

• Standard screw shells are aluminum.(Brass and nickel plated brass available at extra cost.)

• Bracket types available are listed on page B7.• Standard packed 200 to a carton.UL and CUL Listed, 660W, 250V

• Molded black phenolic E26 medium base lampholder with threaded male,threaded female or rivet type brackets.

• Terminal screws are 6-3/2 backed out and installed into contacts.• Standard screw shells are aluminum.

(Brass and nickel plated brass available at extra cost.)• Bracket types available are listed on page B7.• Standard packed 400 to a carton.UL Listed, 660W, 250V

MEDIUM BASE LAMPHOLDERS

• Molded black phenolic E26 medium base socket with threaded male, threadedfemale or rivet type brackets.

• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plastic insulated wire.• Ground wire available upon request. Standard screw shells are aluminum.

(Brass and nickel plated brass available at extra cost.)• Bracket types available are listed on page B7.• Standard packed 400 to a carton.UL Listed, 660W, 250V

Series 303 Porcelain Lampholder

• Unglazed porcelain body on E26 medium base lampholder with threaded male,threaded female or rivet type brackets.

• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plastic insulated wire.(Bare copper ground wire available upon request.)


• Bracket types available are listed on page B7.• Standard packed 200 to a carton.UL and CUL Listed, 660W, 250V

Series 201 Phenolic Lampholder

Series 275 Phenolic Lampholder with Screw Terminals

Non-stocked, Special Order, Call for details





Bracket Type M

Bracket Type L

Bracket Type O

Bracket Type J

Bracket Type F

BRACKET TYPES FOR SERIES 201, 275, 301 & 303

Bracket Type A

Bracket Type B

Bracket Type Number L B A Description

A 012 45mm - - 1/8”- 27” Female Threaded ExtrusionA 013 49mm - - “A 014 51mm - - “A 015 52mm - - “A 016 54mm - - “A 017 61mm - - “A 018 48mm - - “

B 029 47mm 7.90mm - 1/8”- 27” Male Threaded NippleB 030 47mm 9.52mm - “B 031 47mm 12.70mm - “B 032 47mm 15.88mm - “B 033 49mm 7.90mm - “B 034 49mm 9.52mm - “B 035 49mm 12.70mm - “B 036 49mm 15.88mm - “B 037 51mm 7.90mm - “B 038 51mm 9.52mm -- “B 039 51mm 12.70mm - “B 040 51mm 15.88mm - “B 041 52mm 7.90mm - “B 042 52mm 9.52mm -- “B 043 52mm 12.70mm - “B 044 52mm 15.88mm - “B 045 60mm 7.90mm - “B 046 60mm 9.52mm - “B 047 60mm 12.70mm - “B 048 60mm 15.88mm - “

F 001 29mm 7.90mm 27mm 1/8”- 27” Male Threaded NippleF 002 29mm 9.52mm 27mm “F 003 29mm 12.70mm 27mm “F 004 29mm 15.88mm 27mm “F 005 29mm 7.90mm 34mm “F 006 29mm 9.52mm 34mm “F 007 29mm 12.70mm 34mm “F 008 29mm 15.88mm 34mm “F 009 29mm 7.90mm 41mm “F 010 29mm 9.52mm 41mm “F 011 29mm 12.70mm 41mm “F 012 29mm 15.88mm 41mm “F 013 29mm 7.90mm 85mm “F 014 29mm 9.52mm 85mm “F 015 29mm 12.70mm 85mm “F 016 29mm 15.88mm 85mm “

M 001 18mm 18˚ 25mm Double Snap SpringM 002 18mm 18˚ 26mm “

J 001 15mm 9.5mm 38mm 1/8”- 27” Male Threaded NippleJ 002 15mm 9.5mm 43mm “J 003 15mm 9.5mm 51mm “

L 001 15mm - 78mm 4mm Dia. Hole

O 003 37mm - 30mm “



B8


Series 302 Tapered Porcelain Lampholder


• Unglazed porcelain body on E26 medium base lampholder with snap spring brackets.• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plastic insulated wire.(Bare copper ground wire available upon request.)


• Bracket types available are listed on page B8 and B9.• Standard packed 200 to a carton.UL and CUL Listed, 660W, 250V

• Molded black phenolic E26 medium base socket with snap spring brackets.• Standard lead types are AWM 18 gauge 1050, 1250,

1500 plastic insulated wire.• Ground wire available upon request. Standard screw shells are

aluminum. (Brass and nickel plated brass available at extra cost.)• Bracket types available are listed on page B8 and B9.• Standard packed 400 to a carton.UL Listed, 660W, 250V

• Unglazed porcelain body on E26 medium base lampholder with snap spring brackets.• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plastic insulated wire.• Ground wire available upon request. Standard screw shells are aluminum.

(Brass and nickel plated brass available at extra cost.)• Bracket types available are listed on page B8 and B9.• Standard packed 200 to a carton.UL and CUL Listed, 660W, 250V

MEDIUM BASE LAMPHOLDERS WITH SNAP SPRING BRACKETS

Series 202 Harness Set (UR, CUR)

Series 202

BRACKET TYPES FOR SERIES 202, 302 & 304

Bracket Type C

Bracket Type Number L B A DescriptionC 049 19mm 5˚ - Single Snap SpringC 050 19mm 6˚ - “C 051 19mm 10˚ - “C 052 19mm 15˚ - “C 053 19mm 20˚ - “C 054 21mm 5˚ - “C 055 21mm 6˚ - “C 056 21mm 10˚ - “C 057 21mm 15˚ - “C 058 21mm 20˚ - “C 059 24mm 5˚ - “C 060 24mm 6˚ - “C 061 24mm 10˚ - “C 062 24mm 15˚ - “C 063 24mm 20˚ - “C 064 35mm 5˚ - “C 065 35mm 6˚ - “C 066 35mm 10˚ - “



Bracket Type K

Bracket Type Q

Bracket Type Number L B A Description

C 067 35mm 15˚ - Single Snap SpringC 068 35mm 20˚ - “C 069 49mm 5˚ - “C 070 49mm 6˚ - “C 071 49mm 10˚ - “C 072 49mm 15˚ - “C 073 49mm 20˚ - “C 074 50mm 5˚ - “C 075 50mm 6˚ - “C 076 50mm 10˚ - “C 077 50mm 15˚ - “C 078 50mm 20˚ - “C 079 52mm 5˚ - “C 080 52mm 6˚ - “C 081 52mm 10˚ - “C 082 52mm 15˚ - “C 083 52mm 20˚ - “

I 001 45mm - - “

K 003 48mm 26mm 31mm Harness Set Snap Spring

Q 002 45mm 36mm - “

D 019 19mm 5˚ - Single Snap SpringD 020 19mm 6˚ - “D 021 19mm 10˚ - “D 022 19mm 15˚ - “D 023 19mm 20˚ - “D 024 21mm 5˚ - “D 025 21mm 6˚ - “D 026 21mm 10˚ - “D 027 21mm 15˚ - “D 028 21mm 20˚ - “D 029 24mm 5˚ - “D 030 24mm 6˚ - “D 031 24mm 10˚ - “D 032 24mm 15˚ - “D 033 24mm 20˚ - “D 034 35mm 5˚ - “D 035 35mm 6˚ - “D 036 35mm 10˚ - “D 037 35mm 15˚ - “D 038 35mm 20˚ - “D 039 49mm 5˚ - “D 040 49mm 6˚ - “D 041 49mm 10˚ - “D 042 49mm 15˚ - “D 043 49mm 20˚ - “D 044 50mm 5˚ - “D 045 50mm 6˚ - “D 046 50mm 10˚ - “D 047 50mm 15˚ - “D 048 50mm 20˚ - “D 049 52mm 5˚ - “D 050 52mm 6˚ - “D 051 52mm 10˚ - “D 052 52mm 15˚ - “D 053 52mm 20˚ - “

H 003 74mm 5mm - Special Snap Spring

G 003 70mm 22mm - “G 004 74mm 22mm - “

Bracket Type I

BRACKET TYPES FOR SERIES 202, 302 & 304 (CONTINUED)

Bracket Type H

Bracket Type G

Bracket Type D



B10

• Molded black phenolic E26 medium base socket with snap spring bracket.• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plastic insulated wire.• Ground wire available upon request. Standard screw shells are

aluminum.(Brass and nickel plated brass available at extra cost.)• Bracket types available are listed on page B10.• Standard packed 400 to a carton.UL Listed, 660W, 250V

Series 305A Porcelain Lampholder



• Unglazed porcelain body on E26 medium base lampholder with snap spring bracket.• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plastic insulated wire.

(Bare copper ground wire available upon request.)• Standard screw shells are aluminum.

(Brass and nickel plated brass available at extra cost.)• Available with thermal protector. (UR, CUR, 600W, 250VAC)• Bracket types available are listed on page B10.• Standard packed 100 to a carton.UL and CUL Listed, 660W, 250V

• Unglazed porcelain body on E26 medium base lampholder with snap spring bracket.• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plastic insulated wire.• Ground wire available upon request. Standard screw shells are

aluminum. (Brass and nickel plated brass available at extra cost.)• Bracket types available are listed on page B10.• Standard packed 200 to a carton.UL and CUL Listed, 660W, 250V

SNAPIN KEYLESS MEDIUM BASE LAMPHOLDERS

HOLE PATTERN

HOLE PATTERN

HOLE PATTERN

OPTIONAL THERMALPROTECTOR COVER

ALSO AVAILABLE WITHTERMINAL SCREWS

BRACKET TYPES FOR SERIES 205, 305, 307, 405 & 407

Bracket Type Number Description

N 001 205, 305 and 405 only Single Snap SpringN 002 307 and 407 only “

Bracket Type N





Series 407 4kV Porcelain Lampholder



• Unglazed porcelain E26 medium base with cap for 1/8” and 1/4” female IP thread outer thread body and standard cap and insulation disk.

• Standard lead types are AWM 18 gauge 1050, 1250,1500 plastic insulated wire.

• Ground wire available upon request.• Standard screw shells are aluminum. (Brass and nickel

plated brass available at extra cost.)• Standard packed 200 to a carton.UL and CUL listed, 660W, 250V

KEYLESS MEDIUM BASE PORCELAIN LAMPHOLDERS

• Glazed or unglazed porcelain E26 medium base with 6-32 insertand with snap spring bracket specially adapted for recess box use.

• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plasticinsulated wire. (Bare copper ground wire available upon request.)


• Standard packed 200 to a carton.UL and CUL listed, 660W, 220V

SNAPIN MEDIUM BASE PORCELAN LAMPHOLDERS

Bracket Type Number L B A

K 004 41mm 57mm 32mm

• Unglazed porcelain body on E26 medium base lampholder with 4kV pulse rating and snap spring bracket.

• Standard lead types are AWM 16 gauge type SF-2 wire.• Standard screw shells are nickel plated brass. • Bracket types available are listed on page B10.• Standard packed 100 to a carton.UL and CUL listed, 660W, 600V

• Unglazed porcelain body on E26 medium base lampholder with 4kV pulse rating and snap spring bracket.

• Standard lead types are AWM 16 gauge type SF-2 wire.• Standard screw shells are nickel plated brass. • Bracket types available are listed on page B10.• Standard packed 200 to a carton.UL and CUL listed, 660W, 600V

HOLE PATTERN

HOLE PATTERN

B11

1/8 or 1/4 NPTEND CAPS AVAILABLE






B12



• Glazed or Unglazed porcelain E26 medium base with 1/8” or 1/4” threadedaluminum for cap (IP cap female threads) and insulation disk.

• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plasticinsulated wire. Also available with SPT-1 1050 brown or blackor 2000 glass braided silicone rubber insulated wire.(Bare copper ground wire available upon request.)

• Standard screw shells are aluminum. (Brass and nickelplated brass available at extra cost.)


• Unglazed porcelain E26 medium base with 8-32 bushing for mounting.• Standard lead types are AWM 18 gauge 1050, 1250, 1500

plastic insulated wire. (Ground wire available upon request.)• Standard screw shells are aluminum. (Brass and nickel

plated brass available at extra cost.)• Standard packed 200 to a carton.UL and CUL listed, 660W, 250V




• Glazed or unglazed porcelain E26 medium base with 6-32 cernterscrew for mounting. Hole in center contact for easy attachment tohousing. Specially designed for assembly in outdoor castings.

• Standard lead types are AWM 18 gauge 1050, 1250, 1500 plasticinsulated wire. (Ground wire available upon request.)

• Standard screw shells are aluminum. (Brass and nickelplated brass available at extra cost.)


• Glazed or unglazed porcelain E26 medium base with two 6-32 bushingsfor mounting.

• Standard lead types are AWM 18 gauge 1050, 1250, 1500

plastic insulated wire.• Standard screw shells are aluminum.

(Brass and nickel plated brass available at extra cost.)• Standard packed 200 to a carton.UR, CUR Recognized, 660W, 250V







• Glazed or unglazed porcelain E26 medium base with8-32 bushing for mounting.


plastic insulated wire.• Standard screw shells are aluminum.

(Brass and nickel plated brass available at extra cost.)• Standard packed 200 to a carton.UR, CUR Recognized, 660W, 250V




• Glazed or unglazed porcelain E26 medium base, 4kV pulserating with 6-32 center screw for mounting.

• 2000 glass braided silicon insulated wire.• Standard screw shells are nickel plated brass. • Standard packed 200 to a carton.UL and CUL listed, 660W, 600V

• Unglazed porcelain E26 medium base with 8-32 bushingin centerfor attachment.


plastic insulated wire.200˚ glass braided silicone rubber wire also available.


• Standard packed 200 to a carton.UR, CUR Recognized, 660W, 250V


03002 Thermal Protector Cover

• Use instead of heat shrink tubing.• Can be mounted directly to fixture.

B13






B14

KEYLESS MEDIUM BASE 4KV PORCELAN LAMPHOLDERS

Series 471B 4kV Porcelain Lampholder


Series 470A 4kV Porcelain Lampholder

• Glazed or unglazed porcelain E26 medium base, 4kV pulse rating with 2 6-32 bushings for mounting.

• Standard lead types are AWM 16 gauge type SF-2 wire.• Standard screw shells are nickel plated brass. • Open or closed wireway porcelain body.• Standard packed 200 to a carton.UR, CUR Recognized, 660W, 600V

• Glazed or unglazed porcelain E26 medium base, 4kV pulse rating with 2 6-32 bushings for mounting.

• Standard lead types are AWM 16 gauge type SF-2 wire.• Standard screw shells are nickel plated brass. • Standard packed 200 to a carton.UR, CUR Recognized, 660W, 600V

• Glazed or unglazed porcelain E26 medium base, 4kV pulse rating with 2 6-32mounting screws on 7/8 inch centers.

• Standard lead types are AWM 16 gauge type SF-2 wire.• Standard screw shells are nickel plated brass. • Open or closed wireway porcelain body.• Standard packed 200 to a carton.UL and CUL listed, 660W, 600V

Series 614B 4kV Porcelain Lampholder With Lugs

• Porcelain body, E26 Medium Base with 2 6-32 bushings on 3/4 inch centers and 2 lugs for attachment of leads.

• Standard screw shells are nickel plated brass. • Electrical Rating: 660W, 600V, 4kV Pulse Rated.• Standard packed 100 to a carton.UR, CUR Recognized, 600W, 600V

NEW DESIGN LAMPHOLDER WITH LUGS

1/8, 1/4 or 3/8 NPTEND CAPS AVAILABLE

1/8, 1/4 or 3/8 NPTEND CAPS AVAILABLE

1/8, 1/4 or 3/8 NPTEND CAPS AVAILABLENon-stocked, Special Order, Call for details







MOGUL BASE PORCELAIN LAMPHOLDERS

• Glazed or unglazed porcelain base with lamp gripsand 2 8-32 screws for mounting.

• Standard lead types are AWM 16 gauge type SF-2 wire.• Standard screw shells are nickel plated brass. • Open or closed wireway porcelain body.• Standard packed 100 to a carton.UL and CUL listed, 1500W, 600V

• Glazed or unglazed porcelain, 4kV pulse rating with lamp gripsand 2 8-32 bushings on 1 3/8 inch centers.

• Standard lead types are AWM 16 gauge type SF-2 wire.• Standard screw shells are nickel plated brass. • Open or closed wireway porcelain body.• Standard packed 100 to a carton.UR, CUR Recognized, 1500W, 600V

Series 570U 4kV Porcelain Lampholder

Series 571U 4kV Porcelain Lampholder

• Glazed porcelain, 4kV pulse rating with 2 8-32 bushings on 34.93mm centers.

• Standard lead types are AWM 14 gauge type SF-2 wire.• Nickel plated brass screw shell with lamp grips.• 600V, 1500W• Standard packed 50 to a carton.UR, CUR Recognized, 1500W, 600V

• Glazed porcelain, 4kV pulse rating with 2 8-32 screws on 34.93mm centers.

• Standard lead types are AWM 14 gauge type SF-2 wire.• Nickel plated brass screw shell with lamp grips.• 600V, 1500W• Standard packed 50 to a carton.UL, CUL Listed, 1500W, 600V

• SERIES 570U & 571U• FOR OPEN RATED METAL HALIDE LAMPS• 4kV PULSE RATING• GRIP LOCKS U.S. Patent No. 7,178,969



B15






Non-stocked, Special Order, Call for detailsFor more information contact our sales department at 1-800-325-7364 or visit www.interglobal-inc.com 1209.1


B16

MOGUL BASE PORCELAIN LAMPHOLDERS



NEW DESIGN MOGUL SOCKET• SERIES 670 & 671• GRIP LOCK & POSITION ORIENTED IN 1 MODEL• 5kV PULSE RATING



• Glazed or unglazed porcelain, 5kV pulse rating with 28-32 screws on 34.93mm centers.

• Standard lead types are AWM 14 gauge type SF-2 wire.• Nickel plated brass screw shell with lamp grips. Also suitable

for position oriented lamp (see illustration above).• 600V, 1500W• Standard packed 50 to a carton.UL, CUL Listed, 1500W, 600V

• Glazed or unglazed porcelain, 5kV pulse rating with 28-32 bushings on 34.93mm centers.

• Standard lead types are AWM 14 gauge type SF-2 wire.• Nickel plated brass screw shell with lamp grips. Also suitable

for position oriented lamp (see illustration above).• 600V, 1500W• Standard packed 50 to a carton.UR, CUR Recognized, 1500W, 600V




E27 MEDIUM BASE LAMPHOLDERS

Series 502, 504 & 505 Porcelain Lampholders

• Unglazed porcelain phenolic E27medium base lampholder withassorted brackets.

• Standard lead types are AWM 18 gauge1050, & 1250 plastic insulated wire.Green ground wire availableon request.

• Standard screw shells are aluminum.Brass & nickel plated availableat extra cost.

• Bracket types available arelisted below.

• Standard packed 400 to a carton.

Bracket Type N

Bracket Type G Bracket Type HBracket Type A

Bracket Type Number L B DescriptionN 102 30mm - Snap Spring Bracket

G 104 80mm - Special Snap Bracket

H 102 38mm - “

A 101 38mm - 1/8”-27” Female Threaded Extrusion

BRACKET TYPES FOR SERIES E27 MEDIUM BASE

Series 502 Series 504 Series 505

B17



B18

BA15D Bayonet Type Lampholders

TL8PI MiniCan Halogen Lampholder

TL8PB & TL8PD Miniature Halogen Lampholders

HALOGEN LAMPHOLDERS

• These compact lampholders for G5.3 bi-pin halogen lamps are ideally suited forapplications with limited space. They feature a ceramic base with mica cover.

• Product Specifications listed below.

UR, CUR Recognized

• Miniature bi-pin quartz halogenlampholders are designed formulti-base usage and accept G4,GX5.3, and G6.35 basedesignations. They have ceramicbodies with mica covers.

• Product Specifications listed below.UR, CUR Recognized

• Mini-Can lampholder for use withsingle-end halogen T-4 lamps.

• Product Specifications listed below.

UR, CUR Recognized

Catalog Number Wiring Lamp/Base Type Rating

TL-8PA 6”, No. 18 SF-2 200˚C 600V (tinned inners) G5.3 bi-pin 250V-100W

TL-8PJ/K 6”, No. 18 SF-2 200˚C 600V (tinned inners) G5.3 bi-pin 250V-100W

TL-8PB 6”, No. 18 AWM SEW-1 appliance wire 200˚C G4 (MR11), G6.35 250V-100W

TL-8PD 6”, No. 18 AWM SEW-1 appliance wire 200˚C G4 (MR11), G6.35, GX5.3 (MR16) 250V-100W

TL-8PI 12”, No. 18 SF-1 200˚C black and white T4 250V-100W

TL-8PD

TL-8PA

TL-8PK

TL-8PJ/K

TL-8PB

• Bayonet type lampholders for BA15d base lamps• Nickel plated metal shell design• 12”, No. 18 AWG SEW-1 200˚C 300V wire.

UR Recognized

BAYONET LAMPHOLDERS

TL8PA, TL8PK & TL8PJ/K Compact Halogen Lampholders






PC08 Incandescent & Fluorescent Dusk To Dawn Switch

S830 Convenience Outlet

• Fully adjustable two piece cover helps to eliminate strobing caused by light reflected off nearby surfaces• Fits Inter-Global PC-08 Dusk to Dawn Switch• Standard Packed 500 to a carton

0.715”(18.2mm)

1.505”(37.8mm)

1.36”(34.3mm)

0.605” (15.37mm)

0.3125” (7.9mm)

14”(35cm)

1500 C Leads

PC-08

0.715”(18.2mm)

1.505”(37.8mm)

1.36”(34.3mm)

0.605” (15.37mm)

0.3125” (7.9mm)

14”(35cm)

ROTATES 360˚

• Maximum Wattage: Incandescent - 120V, Up to 300 WattsGU24/Fluorescent - 120V, Up to 39 Watts

• Can be used with Electronic and Magnetic Ballast• Electronic Circuit with Mechanical Switching Relay• UR, CUR Recognized• Standard Packed 250 to a carton

LeadStyle Colors Height Width Length LengthPC-08 Black 1.3” .67” 1.45” 14”

CONVENIENCE OUTLETS

• UL Listed, 120V, 15A• Sets include all items shown in drawings. Sets shipped in bulk.• Standard Packed 100 to a carton.• Product Specifications listed below.

1050 C Leads

3 WireConvenience

OutletGasketFlat Head Countersunk

Self Tapping Screw 6-32 X 1”

1050 C Leads

2” (50.8mm)

3.125”(80mm)

.625”(15.9mm)

DUSK TO DAWN SWITCHES

LeadStyle Colors Height Width Deep LengthS830BC Black 3.125” 2” .625” 7.25”S830PC White 3.125” 2” .625” 7.25”

• UL Listed, 125V, 15A• Standard Packed 500 to a carton.• Product Specifications listed below. LeadStyle Colors Height Width Deep Length

15-040BK Black 1” 1” .625” 6.0”15-040WH White 1” 1” .625” 6.0”

Style Colors03-003 Black

03-003WHT White

0.750” (18mm)

0.5625” (14mm)

C1

03003 Dusk To Dawn Switch Swivel Hood and Base

15040 Grounded Convenience Outlet

• Maximum Wattage: Incandescent - 120V, Up to 300 Watts• Can be used with Electronic and Magnetic Ballast• Electronic Circuit W/Mechanical Switching Relay• UL, CUL Listed• Standard Packed 100 to a carton

300WATT

1500 C Leads

LeadStyle Colors Height Width Length LengthS822BC Black 1.687” 1.06” 2” 8” WIRING DIAGRAM

0.715”(18.2mm)

1.505”(37.8mm)

1.36”(34.3mm)

0.605” (15.37mm)

0.3125” (7.9mm)

14”(35cm)

S822BC Incandescent Dusk To Dawn Switch

WIRING DIAGRAM

0.715”(18.2mm)

1.505”(37.8mm)

1.36”(34.3mm)

0.605” (15.37mm)

0.3125” (7.9mm)

14”(35cm)


LeadStyle Colors Height Width Length Length

PTOSW7 Black 1.375” .75” 1.875” 12.5/9”

1.1”(28mm)

1.93”(49mm)

8”(203.2mm)12”

(304.8mm)

1500 C Leads

8.5”(215.9mm)12.5”

(317.5mm)

1500 C Leads

8.5”(215.9mm)12.5”

(317.5mm)

1500 C Leads

PTOSW4

03-024 (Clear)sold seperately

K005BRsold seperately

PTOSW7

PTOSW5

CAUTION: Photocells are not designed for use with external power factor correcting capacitors. For your specific needs, please call Inter-Global on your application. Inter-Global cannotbe responsible for non-Inter-Global equipment which is attached to or used in conjunction with the photocells and all such equipment is expressly excluded from Inter-Global's warranty.

• Maximum Wattage: 120V, Up to 60 Watts• Electronic Circuit• UL Recognized Component Photo Electric Switch• Standard Packed 500 to a carton• Not for use with Fluorescent Lighting

• Maximum Wattage: 120V, Up to 13 Watts• For use with Magnetic Fluorescent Ballast Only• Electronic Circuit• UL Recognized Component Photo Electric Switch• Standard Packed 500 to a carton

• Maximum Wattage: 120V, Up to 13 Watts• For use with Magnetic Fluorescent Ballast Only• Electronic Circuit• UL Recognized Component Photo Electric Switch• Standard Packed 500 to a carton

1.1”(28mm)

1.93”(49mm)

8”(203.2mm)12”

(304.8mm)

1500 C LeadsPTOSW2

• Maximum Wattage: 120V, Up to 60 Watts• Electronic Circuit• UL Recognized Component Photo Electric Switch• Standard Packed 500 to a carton• Not for use with Fluorescent Lighting


PTOSW2 Black 1.06” 1” 1.875” 12.5/8.5”

DUSK TO DAWN SWITCHES (CONTINUED)

C2

PTOSW2 Incandescent Dusk To Dawn Switch

PTOSW4 Magnetic Fluorescent Dusk To Dawn Switch

PTOSW5 Magnetic Fluorescent Dusk To Dawn Switch

PTOSW7 Incandescent Dusk To Dawn Switch


PTOSW5 Black 1.375” .75” 1.875” 12.5/9”


PTOSW4 Black 1.06” 1” 1.875” 12.5/8.5”








Documents

Electrical Components from Inter-Global · lamps fc8t9(22w)g10q xx xx fc12t9(32w) x f8t5 x xx x x x f13t5 x f14t8 x xx x x f15t8 xxxxx xxx x x f17t8 xx x xx x f18t8 xx x xx x f20t8