30
Model Description MODEL BRAND Printing Specification 1. Trim Size (Format) : 215mm x 280 mm 2. Printing Colors Cover : 2 COLORS (M100%, BLACK) Inside : 1 COLORS (Black) 3. Stock (Paper) Cover : 백상지 100 g/Inside : 백상지 100 g/4. Printing Method : 5. Bindery : Saddle stitch 6. Language : English 7. Number of pages : 28 (Including blank 1page) Part No. 1. 2. Service Guide Specification Changes 4. REV. NO. MM/DD/YY SIGNATURE CHANGE NO. CHANGE CONTENTS 1 2 3 4 5 7 6 SUFFIX LEE H.J 05.12.30 L1550S-SNN L1550S-BNN LG 3828TSL094N KIM J.O 05.12.30 (1) Origin Notification * LGEDI : Printed in Indonesia * LGEWA : Printed in U.K. * LGESP : Printed in Brazil * LGEMX : Printed in Mexico * LGENT : Printed in China * LGEIL : Printed in India 8 Special Instructions 3. Product Name ABEUEP FLATRON L1550S

Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

Embed Size (px)

Citation preview

Page 1: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

담 당 관 리 자

Model Description

MODEL BRAND

Printing Specification

1. Trim Size (Format) : 215mm x 280 mm

2. Printing Colors• Cover : 2 COLORS (M100%, BLACK)• Inside : 1 COLORS (Black)

3. Stock (Paper)• Cover : 백상지 100 g/• Inside : 백상지 100 g/

4. Printing Method : 5. Bindery : Saddle stitch6. Language : English7. Number of pages : 28 (Including blank 1page)

Part No.

1.

2.

Service Guide SpecificationService Guide Specification

Changes 4.

REV.NO. MM/DD/YY SIGNATURE CHANGE NO. CHANGE CONTENTS

1

2

3

4

5

7

6

SUFFIX

LEE H.J05.12.30

L1550S-SNNL1550S-BNN LG

3828TSL094N

KIM J.O05.12.30

(1) Origin Notification* LGEDI : Printed in Indonesia * LGEWA : Printed in U.K.* LGESP : Printed in Brazil * LGEMX : Printed in Mexico* LGENT : Printed in China * LGEIL : Printed in India

8

Special Instructions3.

Product NameABEUEP FLATRON L1550S

Page 2: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

Pagination sheetPagination sheet P/NO. 3828TSL094NTotal pages :28pages

CoverEnglish

2

English

3

English

4

English

….

English

…..

Rear Cover

Front coverInside

blank

English

….

English

22

English

23

English

24

English

25

Rear coverInside

26

Page 3: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

COLOR MONITORSERVICE MANUAL

Website:http://biz.LGservice.comE-mail:http://www.LGEservice.com/techsup.html

CAUTIONBEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS NO. : CL-82

MODEL: L1550S (L1550S-SNN.AB**EP,AN**EP)L1550S (L1550S-BNN.AB**EP,AN**EP)

( ) **Same model for Service

*To apply the MSTAR Chip.

Page 4: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

Blank Page1

Page 5: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 2 -

CONTENTS

SPECIFICATIONS ................................................... 2PRECAUTIONS ....................................................... 3TIMING CHART ....................................................... 7DISASSEMBLY ....................................................... 8BLOCK DIAGRAM ................................................... 9DESCRIPTION OF BLOCK DIAGRAM....................10ADJUSTMENT ...................................................... 12

SERVICE OSD ...................................................... 13

TROUBLESHOOTING GUIDE .............................. 14

WIRING DIAGRAM ............................................... 18

EXPLODED VIEW...................................................19

REPLACEMENT PARTS LIST ...............................21

SCHEMATIC DIAGRAM......................................... 23

1. LCD CHARACTERISTICSType : TFT Color LCD ModuleActive Display Area : 15 inchSize : 326.5(W) x 253.5(H) x 11.2(D)Pixel Pitch : 0.297 (H) x 0.297 (V)Color Depth : 6bit with FRC, 16M clolorsElectrical Interface : LVDSSurface Treatment : Hard-coating(3H), Anti-GlareOperating Mode : Normally White, Transmissive modeBacklight Unit : 2-CCFL

2. OPTICAL CHARACTERISTICS2-1. Viewing Angle by Contrast Ratio ≥ 10CPT TNLeft : 60°min. Right : 70°(Typ)Top : 50°min., 60°(Typ) Bottom : 55°min., 65°(Typ)

LPL TNLeft : 55°min., 65°(Typ) Right : 55°min., 65°(Typ)Top : 40°min., 45°(Typ) Bottom : 50°min., 55°(Typ)

2-2. Luminance : 200(min), 250(Typ)

2-3. Contrast Ratio : 300(min), 400(Typ)

3. SIGNAL (Refer to the Timing Chart)3-1. Sync Signal

• Type : Separate Sync.

3-2. Video Input Signal1) Type : R, G, B Analog2) Voltage Level : 0~0.71 Va) Color 0, 0 : 0 Vp-pb) Color 7, 0 : 0.467 Vp-pc) Color 15, 0 : 0.714 Vp-p

3) Input Impedance : 75 Ω

3-3. Operating FrequencyHorizontal : 30 ~ 63kHzVertical : 56 ~ 75Hz

4. Max. ResolutionD-sub Analog : 1024 x 768@75Hz

5. POWER SUPPLY

5-1. Power : AC 100~240V, 50/60Hz , 1.0A

5-2. Power Consumption

6. ENVIRONMENT

6-1. Operating Temperature : 10°C~35°C 6-2. Relative Humidity : 10%~80%6-3. MTBF : 50,000 HRS with 90%

Confidence levelLamp Life : 40,000 Hours(Min)

7. DIMENSIONS (with TILT/SWIVEL)

Width : 356.8 mm (14.05'')Depth : 151.7 mm (5.97'')Height : 359.8 mm (14.17'')

8. WEIGHT (with TILT/SWIVEL)

Net. Weight : 4.1 kg (9.04 lbs)Gross Weight : 5.0 kg (11.02 lbs)

SPECIFICATIONS

MODE

POWER ON (NORMAL)

STAND-BY

SUSPEND

DPMS OFF

H/V SYNC

ON/ON

OFF/ON

ON/OFF

OFF/OFF

POWER CONSUMPTION

less than 25 W

less than 1 W

less than 1 W

less than 1 W

LED COLOR

GREEN

AMBER

AMBER

AMBER

VIDEO

ACTIVE

OFF

OFF

OFF

Page 6: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 3 -

WARNING FOR THE SAFETY-RELATED COMPONENT.

• There are some special components used in LCDmonitor that are important for safety. These parts aremarked on the schematic diagram and thereplacement parts list. It is essential that these criticalparts should be replaced with the manufacturer’sspecified parts to prevent electric shock, fire or otherhazard.

• Do not modify original design without obtaining writtenpermission from manufacturer or you will void theoriginal parts and labor guarantee.

TAKE CARE DURING HANDLING THE LCD MODULEWITH BACKLIGHT UNIT.

• Must mount the module using mounting holes arrangedin four corners.

• Do not press on the panel, edge of the frame stronglyor electric shock as this will result in damage to thescreen.

• Do not scratch or press on the panel with any sharpobjects, such as pencil or pen as this may result indamage to the panel.

• Protect the module from the ESD as it may damage theelectronic circuit (C-MOS).

• Make certain that treatment person’s body aregrounded through wrist band.

• Do not leave the module in high temperature and inareas of high humidity for a long time.

• The module not be exposed to the direct sunlight.

• Avoid contact with water as it may a short circuit withinthe module.

• If the surface of panel become dirty, please wipe it offwith a softmaterial. (Cleaning with a dirty or rough clothmay damage the panel.)

WARNING

BE CAREFUL ELECTRIC SHOCK !

• If you want to replace with the new backlight (CCFL) orinverter circuit, must disconnect the AC adapterbecause high voltage appears at inverter circuit about650Vrms.

• Handle with care wires or connectors of the invertercircuit. If the wires are pressed cause short and mayburn or take fire.

Leakage Current Hot Check Circuit

PRECAUTION

CAUTIONPlease use only a plastic screwdriver to protect yourselffrom shock hazard during service operation.

1.5 Kohm/10W

To Instrument'sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

Page 7: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 4 -

SERVICING PRECAUTIONSCAUTION: Before servicing receivers covered by thisservice manual and its supplements and addenda, readand follow the SAFETY PRECAUTIONS on page 3 of thispublication.NOTE: If unforeseen circumstances create conflictbetween the following servicing precautions and any of thesafety precautions on page 3 of this publication, alwaysfollow the safety precautions. Remember: Safety First.

General Servicing Precautions1. Always unplug the receiver AC power cord from the AC

power source before;a. Removing or reinstalling any component, circuit

board module or any other receiver assembly.b. Disconnecting or reconnecting any receiver electrical

plug or other electrical connection.c. Connecting a test substitute in parallel with an

electrolytic capacitor in the receiver.CAUTION: A wrong part substitution or incorrectpolarity installation of electrolytic capacitors mayresult in an explosion hazard.

d. Discharging the picture tube anode.2. Test high voltage only by measuring it with an

appropriate high voltage meter or other voltagemeasuring device (DVM, FETVOM, etc) equipped witha suitable high voltage probe.Do not test high voltage by "drawing an arc".

3. Discharge the picture tube anode only by (a) firstconnecting one end of an insulated clip lead to thedegaussing or kine aquadag grounding system shieldat the point where the picture tube socket ground leadis connected, and then (b) touch the other end of theinsulated clip lead to the picture tube anode button,using an insulating handle to avoid personal contactwith high voltage.

4. Do not spray chemicals on or near this receiver or anyof its assemblies.

5. Unless specified otherwise in this service manual,clean electrical contacts only by applying the followingmixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator;10% (by volume) Acetone and 90% (by volume)isopropyl alcohol (90%-99% strength)CAUTION: This is a flammable mixture.Unless specified otherwise in this service manual,lubrication of contacts in not required.

6. Do not defeat any plug/socket B+ voltage interlockswith which receivers covered by this service manualmight be equipped.

7. Do not apply AC power to this instrument and/or any ofits electrical assemblies unless all solid-state deviceheat sinks are correctly installed.

8. Always connect the test receiver ground lead to thereceiver chassis ground before connecting the testreceiver positive lead.Always remove the test receiver ground lead last.

9. Use with this receiver only the test fixtures specified inthis service manual.CAUTION: Do not connect the test fixture ground strapto any heat sink in this receiver.

Electrostatically Sensitive (ES) DevicesSome semiconductor (solid-state) devices can bedamaged easily by static electricity. Such componentscommonly are called Electrostatically Sensitive (ES)Devices. Examples of typical ES devices are integratedcircuits and some field-effect transistors andsemiconductor "chip" components. The followingtechniques should be used to help reduce the incidence ofcomponent damage caused by static by static electricity.1. Immediately before handling any semiconductor

component or semiconductor-equipped assembly, drainoff any electrostatic charge on your body by touching aknown earth ground. Alternatively, obtain and wear acommercially available discharging wrist strap device,which should be removed to prevent potential shockreasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped withES devices, place the assembly on a conductivesurface such as aluminum foil, to prevent electrostaticcharge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder orunsolder ES devices.

4. Use only an anti-static type solder removal device.Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient todamage ES devices.

5. Do not use freon-propelled chemicals. These cangenerate electrical charges sufficient to damage ESdevices.

6. Do not remove a replacement ES device from itsprotective package until immediately before you areready to install it. (Most replacement ES devices arepackaged with leads electrically shorted together byconductive foam, aluminum foil or comparableconductive material).

7. Immediately before removing the protective materialfrom the leads of a replacement ES device, touch theprotective material to the chassis or circuit assemblyinto which the device will be installed.CAUTION: Be sure no power is applied to the chassisor circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackagedreplacement ES devices. (Otherwise harmless motionsuch as the brushing together of your clothes fabric orthe lifting of your foot from a carpeted floor cangenerate static electricity sufficient to damage an ESdevice.)

Page 8: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 5 -

General Soldering Guidelines1. Use a grounded-tip, low-wattage soldering iron and

appropriate tip size and shape that will maintain tiptemperature within the range or 500。F to 600。F.

2. Use an appropriate gauge of RMA resin-core soldercomposed of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.4. Thoroughly clean the surfaces to be soldered. Use a

mall wire-bristle (0.5 inch, or 1.25cm) brush with ametal handle.Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering techniquea. Allow the soldering iron t ip to reach normal

temperature.(500。F to 600。F)

b. Heat the component lead until the solder melts.c. Quickly draw the melted solder with an anti-static,

suction-type solder removal device or with solderbraid.CAUTION: Work quickly to avoid overheating thecircuitboard printed foil.

6. Use the following soldering technique.a. Allow the soldering iron tip to reach a normal

temperature (500。F to 600。F)b. First, hold the soldering iron tip and solder the strand

against the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction ofthe component lead and the printed circuit foil, andhold it there only until the solder flows onto andaround both the component lead and the foil.CAUTION: Work quickly to avoid overheating thecircuit board printed foil.

d. Closely inspect the solder area and remove anyexcess or splashed solder with a small wire-bristlebrush.

IC Remove/ReplacementSome chassis circuit boards have slotted holes (oblong)through which the IC leads are inserted and then bent flatagainst the circuit foil. When holes are the slotted type,the following technique should be used to remove andreplace the IC. When working with boards using thefamiliar round hole, use the standard technique asoutlined in paragraphs 5 and 6 above.

Removal1. Desolder and straighten each IC lead in one operation

by gently prying up on the lead with the soldering irontip as the solder melts.

2. Draw away the melted solder with an anti-staticsuction-type solder removal device (or with solderbraid) before removing the IC.

Replacement1. Carefully insert the replacement IC in the circuit board.2. Carefully bend each IC lead against the circuit foil pad

and solder it.3. Clean the soldered areas with a small wire-bristle

brush. (It is not necessary to reapply acrylic coating tothe areas).

"Small-Signal" Discrete TransistorRemoval/Replacement1. Remove the defective transistor by clipping its leads as

close as possible to the component body.2. Bend into a "U" shape the end of each of three leads

remaining on the circuit board.3. Bend into a "U" shape the replacement transistor leads.4. Connect the replacement transistor leads to the

corresponding leads extending from the circuit boardand crimp the "U" with long nose pliers to insure metalto metal contact then solder each connection.

Power Output, Transistor DeviceRemoval/Replacement1. Heat and remove all solder from around the transistor

leads.2. Remove the heat sink mounting screw (if so equipped).3. Carefully remove the transistor from the heat sink of the

circuit board.4. Insert new transistor in the circuit board.5. Solder each transistor lead, and clip off excess lead.6. Replace heat sink.

Diode Removal/Replacement1. Remove defective diode by clipping its leads as close

as possible to diode body.2. Bend the two remaining leads perpendicular y to the

circuit board.3. Observing diode polarity, wrap each lead of the new

diode around the corresponding lead on the circuitboard.

4. Securely crimp each connection and solder it.5. Inspect (on the circuit board copper side) the solder

joints of the two "original" leads. If they are not shiny,reheat them and if necessary, apply additional solder.

Fuse and Conventional ResistorRemoval/Replacement1. Clip each fuse or resistor lead at top of the circuit board

hollow stake.2. Securely crimp the leads of replacement component

around notch at stake top.3. Solder the connections.

CAUTION: Maintain original spacing between thereplaced component and adjacent components and thecircuit board to prevent excessive componenttemperatures.

Page 9: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 6 -

Circuit Board Foil RepairExcessive heat applied to the copper foil of any printedcircuit board will weaken the adhesive that bonds the foilto the circuit board causing the foil to separate from or"l i f t-off" the board. The following guidelines andprocedures should be followed whenever this condition isencountered.

At IC ConnectionsTo repair a defective copper pattern at IC connections usethe following procedure to install a jumper wire on thecopper pattern side of the circuit board. (Use thistechnique only on IC connections).

1. Carefully remove the damaged copper pattern with asharp knife. (Remove only as much copper asabsolutely necessary).

2. carefully scratch away the solder resist and acryliccoating (if used) from the end of the remaining copperpattern.

3. Bend a small "U" in one end of a small gauge jumperwire and carefully crimp it around the IC pin. Solder theIC connection.

4. Route the jumper wire along the path of the out-awaycopper pattern and let it overlap the previously scrapedend of the good copper pattern. Solder the overlappedarea and clip off any excess jumper wire.

At Other ConnectionsUse the following technique to repair the defective copperpattern at connections other than IC Pins. This techniqueinvolves the installation of a jumper wire on thecomponent side of the circuit board.1. Remove the defective copper pattern with a sharp

knife.Remove at least 1/4 inch of copper, to ensure that ahazardous condition will not exist if the jumper wireopens.

2. Trace along the copper pattern from both sides of thepattern break and locate the nearest component that isdirectly connected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the leadof the nearest component on one side of the patternbreak to the lead of the nearest component on theother side.Carefully crimp and solder the connections.CAUTION: Be sure the insulated jumper wire isdressed so the it does not touch components or sharpedges.

Page 10: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

TIMING CHART

- 7 -

<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >>

VIDEO

SYNC

B

C

E

A

D

MODE H / VSync

PolarityFrequency

TotalPeriod

( E )

Blanking Time ( B )

DotClock

1 H(Pixels) + 25.175 31.468 KHz 800 640 16 96 48 640 x 350

V(Lines) - 70.0 Hz 449 350 37 2 60

2 H(Pixels) - 28.322 31.468 KHz 900 720 17 108 55 720 x 400

V(Lines) + 70.0 Hz 449 400 13 2 34 (TEXT)

3 H(Pixels) - 25.175 31.469 KHz 800 640 16 96 48 640 x 480

V(Lines) - 60.0 Hz 525 480 10 2 33

4 H(Pixels) - 30.24 35.00 KHz 864 640 64 64 96 640 x 480

V(Lines) - 66.67 Hz 525 480 3 3 39

5 H(Pixels) - 31.5 37.861 KHz 832 640 24 40 128 640 x 480

V(Lines) - 72.8 Hz 520 480 9 3 28

6 H(Pixels) - 31.5 37.50KHz 840 640 16 64 120 640 x 480

V(Lines) - 75.0 Hz 500 480 1 3 16

7 H(Pixels) + 36.0 35.156 KHz 1024 800 24 72 128 800 x 600

V(Lines) + 56.25 Hz 625 600 1 2 22

8 H(Pixels) + 40.0 37.879 KHz 1056 800 40 128 88 800 x 600

V(Lines) + 60.3 Hz 628 600 1 4 23

9 H(Pixels) + 50.0 48.077 KHz 1040 800 56 120 64 800 x 600

V(Lines) + 72.188 Hz 666 600 37 6 23

10 H(Pixels) + 49.5 46.875 KHz 1056 800 16 80 160 800 x 600

V(Lines) + 75.0 Hz 625 600 1 3 21

11 H(Pixels) - 57.2832 49.725 KHz 1152 832 32 64 224 832 x 624

V(Lines) - 74.55 Hz 667 624 1 3 39 (MAC)

12 H(Pixels) - 65 48.363 KHz 1344 1024 24 136 160 1024 x 768

V(Lines) - 60.0 Hz 806 768 3 6 29

13 H(Pixels) - 75 56.476 KHz 1328 1024 24 136 144 1024 x 768

V(Lines) - 70.0 Hz 806 768 3 6 29

14 H(Pixels) + 78.75 60.023 KHz 1312 1024 16 96 176 1024 x 768

V(Lines) + 75.0 Hz 800 768 1 3 28

VideoActive

Time ( A )

SyncDuration

( D )

FrontPorch ( C )

Resolution

Page 11: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 8 -

DISASSEMBLY

Remove the screws.

Remove the 6 screws from each up of metal frame.

# 1

1. Pull the front cover upward.2. Then, let the all latches are separated.3. Put the front face down.

Remove Al-tape from control pcb fix.Pell off Al-tape from panel.

# 2

# 3 # 4

# 5 # 6

Remove the 4 screws from each side of metalframe.

Disassemble back cover.

# 7

Page 12: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 9 -

D-S

UB

TS

U16

AL

incl

ud

ing

(AD

C/L

VD

S/S

CA

LE

R/IN

PU

T S

WIT

CH

ING

/TM

DS

)

MT

V31

2M

ICO

M

LC

D M

od

ule

R,G

,B

dif

fere

nti

al

LIP

S5V

3.3

V

AC

In

pu

t

TS

U16

AL

&T

R(K

TA12

73)

12V

R,G

,B, H

/V S

ync

1.8

V

3.3

V1

1.8

V

3.3

V1

3.3V

Reg

. 7

8D33

5V

3.3

V1

3.3V

Reg

. 7

8D33

5V 3.3

V

LVD

S(L

ow

Vo

ltag

eD

iffe

ren

tial

Sig

nal

ing

)

BLOCK DIAGRAM

Page 13: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 10 -

DESCRIPTION OF BLOCK DIAGRAM

1. Video Controller Part.This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to thedigital video signal using a pixel clock.The pixel clock for each mode is generated by the PLL.The range of the pixel clock is from 25MHz to 78.75MHz.This part consists of the Scaler, ADC and TMDS receiver .The Scaler gets the video signal converted analog to digital, interpolates input to 1024 x 768 resolution signal andoutputs 8-bit R, G, B signal to transmitter.

2. Power Part.This part consists of the two 3.3V regulator to convert power which is provided 12V, 5V in Power board and Micom.3.3V is provided for LCD panel.Also, 5V is converted 3.3V by regulator and 3.3V and 1.8V are provided for scaler. Converted power is provided for IC in the main board.

3. MICOM Part.This part consists of EEPROM IC which stores control data and the Micom.The Micom distinguishes polarity and frequency of the H/V sync supplied from signal cable.The controlled data of each modes is stored in EEPROM.

Page 14: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 11 -

EMICOMPONENTS

LINE100 ~ 240V

INPUT RECTIFIERAND FILTER

ENERGYTRANSFER

OUTPUT RECTIFIERAND FILTER

12V

5V

GND

SIGNALCOLLENT-

ION

PHOTO- COUPLERISOLATION

HVDC 100KHz

PRIMARY SECONDARY

50 ~ 60Hz

PWMCOMTROLCIRCUIT

Operation description_LIPS

LIPS Board Block Diagram

1. EMI components.This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, thecircuit included a line-filter, across line capacitor and of course the primary protection fuse.

2. Input rectifier and filter.This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.

3. Energy Transfer.This part function is transfer the primary energy to secondary through a power transformer.

4. Output rectifier and filter.This part function is to make a pulse width modulation control and to provide the driver signal to power switch, toadjust the duty cycle during different AC input and output loading condition to achive the dc output stablize, and alsothe over power protection is also monitor by this part.

5. Photo-Coupler isolation.This part function is to feed back the DC output changing status through a photo transistor to primary controller toachieve the stabilized DC output voltage.

6. Signal collection.This part function is to collect the any change from the DC output and feed back to the primary through phototransistor.

Page 15: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 12 -

ADJUSTMENT

Windows EDID V1.0 User Manual

Operating System: MS Windows 98, 2000, XPPort Setup: Windows 98 => Don’t need setup

Windows 2000, XP => Need to Port Setup.This program is available to LCD Monitor only.

1. Port Setupa) Copy “UserPort.sys” file to

“c:\WINNT\system32\drivers” folderb) Run Userport.exe

c) Remove all default numberd) Add 300-3FF

e) Click Start button.f) Click Exit button.

2. EDID Read & Write1) Run WinEDID.exe

2) Edit Week of Manufacture, Year of Manufacture, Serial Numbera) Input User Info Datab) Click “Update” buttonc) Click “ Write” button

Page 16: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 13 -

220

IBMCompatible PCVideo Signal

Generator

PARALLEL PORT

Power inlet (required)

Power LED

ST Switch

Power Select Switch(110V/220V)

Con

trol

Lin

e

Not u

sed

RS232

C

PARAL

LEL

V-SY

NC

POW

ER

ST

VGS

MONITOR

E

E

V-Sync On/Off Switch(Switch must be ON.)

F

F

A

A

BB

C

C

15105

5

69

1

1

1

14

13

25

6

5V

5V

5V

4.7K4.7K

4.7K

74LS06

74LS06

OFF ON

OFF

ON

11

Figure 1. Cable Connection

SERVICE OSD

1) Turn off the power switch at the front side of the display.

2) Wait for about 5 seconds and press MENU, POWER switch with 1 second interval.

3) The SVC OSD menu contains additional menus that the User OSD menu as described below.

a) Auto Color : W/B balance and Automatically sets the gain and offset value.b) NVRAM INIT : EEPROM initialize.(24C08)c) CLEAR ETI : To initialize using time.d) AGING : Select Aging mode(on/off).e) R/G/B-9300K : Allows you to set the R/G/B-9300K value manually.f) R/G/B-6500K : Allows you to set the R/G/B-6500K value manually.g) R/G/B-Offset : Allows you to set the R/G/B-Offset value manually.(Analog Only) h) R/G/B-Gain : Allows you to set the R/G/B-Gain value manually.(Analog Only)i) MODULE : To select applied module.

Page 17: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 14 -

TROUBLESHOOTING GUIDE

1. NO POWER

NO POWER(POWER INDICATOR OFF)

CHECK KEY CONTROLCONNECTOR ROUTINE

CHECK U201

NO

NO

NO

CHECK POWER BOARD,AND FIND OUT A SHORTPOINT AS OPENING EACH POWER LINE

CHECK 5VS LINE(OPEN CHECK)

CHECK 3.3V LINE

NOCHECK X-TAL

YES

YES

YES

YES

CHECK J707 VOLTAGE PIN5, PIN6 (5V)?

CHECK U501 PIN VOLTAGE

(5V) ?

IS U201 PIN90 (3.3V) VOLTAGE ?

CHECK U201 PIN 96 PULSE

1

NO PROBLEM

1

Waveforms

U201-#96

Page 18: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 15 -

2. NO RASTER (OSD IS NOT DISPLAYED) – LIPS

NO RASTER(OSD IS NOT DISPLAYED)

NO

NO

NO

NO

REPLACE CCFL LAMPIN THE LCD MODULE

CHECK POWER BOARD,AND FIND OUT A SHORTPOINT AS OPENING EACH POWER LINE

CHECK MICOM INVON/OFF PORT.

1. CONFIRM BRIGHTNESSOSD CONTRL STATE.

2. CHECK MICOM DIM-ADJ PORT

LIPS

YES

YES

YES

YES

J707PIN5, PIN6

5V?

J707 PIN22.5V?

J707 PIN15V?

CHECK PULSE AS

CONTACTING SCOPE PROBE TO CAUTION LABEL.

(CONTACT PROBE TO CAUTION LABEL.

CAN YOU SEE PULSE AT YOUR SCOPE?

Page 19: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 16 -

3. NO RASTER (OSD IS NOT DISPLAYED) – Mstar

NO RASTER(OSD IS NOT DISPLAYED)

NO

NO

NO

TROUBLE IN CABLE OR LCD MODULE

CHECK U801 (17", 19")CHECK U803 (15")

1. CHECK PIN122, 123 SOLDERING CONDITION

2. CHECK X5013. TROUBLE IN U201

CHECK CONNECTIONLINE FROM D-SUB TOU501

YES

YES

YES

U201PIN 18, 90

3.3V?

U201 PIN96, 97

OSCILLATE AS12MHZ?

U501PIN43 IS 48KHz H-SYNC?PIN44 IS 60Hz V-SYNC?IS PULSE APPEARED

AT SIGNAL PINS?AT MODE 12?

1

2

1 2

Waveforms

U201-#96, 97 U501-#43 H-SYNC 2 U501-#44 V-SYNC

Page 20: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 17 -

4. TROUBLE IN DPM

TROUBLE IN DPM

NO

NO

TROUBLE IN U501

CHECK PC PC IS NOT GOINGINTO DPM OFF MODE

CHECK H/V SYNC LINE

YES

YES

CHECK R216, R217R778, R781

CHECKU501 PIN 43.44SYNC PULSE ?

3

3

Waveforms

R216, R778 H-Sync 3 R217, R781 V-Sync

Page 21: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 18 -

WIRING DIAGRAM

6631T11012R

6631T11022C

Page 22: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

EXPLODED VIEW

- 19 -

010

060

020

070 08

0

090

040 05

0

100

110

030

Page 23: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 20 -

EXPLODED VIEW PARTS LIST

DescriptionPart No.Ref. No.

3091TKL157C CABINET ASSEMBLY, L1550 BRAND 3090TKL140 SILVER-Europe,Singapore,U.K

3091TKL157E CABINET ASSEMBLY, L1550 BRAND 3090TKL140 SILVER, AUSTRALIA, LIFE IS GOOD

3091TKL157D CABINET ASSEMBLY, L1550 BRAND 3090TKL140 SILVER, C-C/SKD

3091TKL157G CABINET ASSEMBLY, L1550 BRAND 3090TKL140 BLACK

6304FCP005A LCD(LIQUID CRYSTAL DISPLAY), CLAA150XP01 CHUNGHWA PICTURE TUBES LTD. TFT COLOR 0/3/3 DOT,250NT/16MS/PSWG

6304FLP156A LCD(LIQUID CRYSTAL DISPLAY), LM150X08-A4NA LG PHILPS TFT COLOR PSWG,LVDS,16MS,SS S D-IC LPL NJ,250NITS

3809TKL110A BACK COVER ASSEMBLY, L1550 3808TKL112 .-SILVER

3809TKL110B BACK COVER ASSEMBLY, L1550 3808TKL112 A-C/SKD-Europe,U.K,Russia

3809TKL110F BACK COVER ASSEMBLY, L1550 3808TKL112 SVC LABEL FOR LATIN AMERICA, E-C/SKD-Panama,Mexico

3809TKL110G BACK COVER ASSEMBLY, L1550 3808TKL112 ABS350 9930(BLACK)-Singapore

3809TKL110J BACK COVER ASSEMBLY, L1550 3808TKL112 ABS350 9930(BK) SVC LABEL FOR LATIN AMERICA-Panama

3043TKK241A TILT SWIVEL ASSEMBLY, L1550 . TILT STAND BODY

3043TKK241B TILT SWIVEL ASSEMBLY, L1550 . TILT STAND BODY, A-C/SKD

3043TKK242A TILT SWIVEL ASSEMBLY, L1550 . TILT STAND BASE

3043TKK242B TILT SWIVEL ASSEMBLY, L1550 . TILT STAND BASE, A-C/SKD

6871TSTA51A PWB(PCB) ASSEMBLY,SUB, L1550SN CONTROL TOTAL BRAND GUMI LF

6871TSTA51C PWB(PCB) ASSEMBLY,SUB, L1550SN CONTROL TOTAL BRAND LGEDI LF-C/SKD-Europe,U.K

6871TSTA51B PWB(PCB) ASSEMBLY,SUB, L1550SN CONTROL TOTAL BRAND LGENT LF-C/SKD-Russia

6871TSTA51D PWB(PCB) ASSEMBLY,SUB, L1550SN CONTROL TOTAL BRAND LGEMX LF-C/SKD-Panama,Mexico

4951TKS219B METAL ASSEMBLY, FRAME L1550S AU, CPT TN

4951TKS219A METAL ASSEMBLY, FRAME L1550S-LPL TN

4951TKS219C METAL ASSEMBLY, FRAME L1550S LPL A-C/SKD

6871TPT282E PWB(PCB) ASSEMBLY,POWER, M-CHASSIS 15INCH C306 68PF 450V POWER TOTAL LIEN CHANG PB FREE

3313TL5128A MAIN TOTAL ASSEMBLY, L1550SN BRAND MST LPL CL-82 LF

3313TL5128F MAIN TOTAL ASSEMBLY, L1550SN.KNEUEPD BRAND CL-82 LF-C/SKD-Europe,U.K

3313TL5128C MAIN TOTAL ASSEMBLY, L1550SN.KNRUEPT BRAND CL-82 LF-C/SKD-Russia

3313TL5128G MAIN TOTAL ASSEMBLY, L1550SN.KNMXEPM BRAND CL-82 LF-C/SKD-Panama,Mexico

4951TKS218A METAL ASSEMBLY, FRAME L1550 REAR FRAME ASSY

4951TKS218B METAL ASSEMBLY, FRAME L1550 REAR FRAME ASSY, A-C/SKD

6410TEW010A POWER CORD, LP34A+LS60 LONGWELL VDE/SEMKO 1870MM WALL CD/PB FREE BLACK-For Europe

6410TSW003A POWER CORD, LP-23A+LS-13 LONGWELL SAA 1870MM WALL CD/PB FREE BLACK-For Australia,Russia

6410TBW004A POWER CORD, LP-61+LS-60 LONGWELL BSI 1870MM WALL CD/PB FREE BLACK-For Singapore,U.K

6410TUW008A POWER CORD, LP31+LS13 LONGWELL UL/CSA 1870MM WALL CD/PB FREE BLACK-For-Mexico,Panama

6410TCW007A POWER CORD, LSG-31+LS-70 LONGWELL CCC 1870MM WALL CD/PB FREE BLACK-For China

010

020

030

040

050

060

070

080

090

100

110

Page 24: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 21 -

DATE: 2005. 12. 16. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION

C204 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC205 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC206 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC207 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC211 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC213 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC214 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC215 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC216 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC217 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC218 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC219 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC220 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC221 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC222 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC223 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC224 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC225 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC226 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC230 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC231 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC232 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC233 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC240 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC251 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC503 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC504 0CH8106F611 10UF 16V M 85STD(CYL) R/TPC506 0CC030CK01A 3PF 1608 50V 0.25 PF R/TP NPC507 0CC180CK41A 18PF 1608 50V 5% R/TP NP0C508 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC701 0CK105CD56A 1UF 1608 10V 10% R/TP X7RC707 0CC680CK41A 68PF 1608 50V 5% R/TP NP0C708 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC709 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC717 0CC101CK41A 100PF 1608 50V 5% R/TP NP0C718 0CC101CK41A 100PF 1608 50V 5% R/TP NP0C727 0CK105CD56A 1UF 1608 10V 10% R/TP X7RC732 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC733 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC734 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC735 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC744 0CC680CK41A 68PF 1608 50V 5% R/TP NP0C803 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"C803 0CE107EF628 "100UF KMG,RD 16V 20% FM2.5 T"-C/SKD-For Mexico,PaanamaC809 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(YC812 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"C812 0CE107EF628 "100UF KMG,RD 16V 20% FM2.5 T"-C/SKD-For Mexico,PanamaC814 0CE107EF610 "100UF KMG,RD 16V 20% FL BULK"C814 0CE107EF628 "100UF KMG,RD 16V 20% FM2.5 T"-C/SKD-For Mexico,PanamaC817 0CK105CD56A 1UF 1608 10V 10% R/TP X7RC818 0CK333CK56A 33000PF 1608 50V 10% R/TP X7C819 0CK105CD56A 1UF 1608 10V 10% R/TP X7R

DATE: 2005. 12. 16. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION

D701 0DSIH00018A "ENKMC2837-T112,LF ISAHAYA R/"D702 0DSIH00018A "ENKMC2837-T112,LF ISAHAYA R/"D706 0DSIH00018A "ENKMC2837-T112,LF ISAHAYA R/"ZD701 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"ZD702 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"ZD703 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"ZD704 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"ZD711 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"ZD712 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"

Q502 0IKE704200H KIA7042AP TO-92 TP 4.2 VOLT.U201 0IPRPM3017A "TSU16AL-LF MSTAR 100P,QFP TR"U501 0IZZTSZ710A L1550SN MST MICOM ASSY MTV31U501 0IZZTSZ710B L1550S-SNN MST MICOM ASSY MT-C/SKD-For ChinaU502 0ICS240813B "CAT24WC08J-TE13 8P,SOIC R/TP"U801 0IPMGKE011A KIA78D33F KEC DPAK R/TP 3.3VU803 0IPMGKE011A KIA78D33F KEC DPAK R/TP 3.3V

Q503 0TRIH80001A "RT1C3904-T112,LF ISAHAYA R/T"Q503 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP-C/SKD-For Russia,ChinaQ504 0TRIH80001A "RT1C3904-T112,LF ISAHAYA R/T"Q504 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP-C/SKD-For Russia,ChinaQ505 0TRIH80001A "RT1C3904-T112,LF ISAHAYA R/T"Q505 0TR390409AE FAIRCHILD KST3904(LGEMTF) TP-C/SKD-For Russia,ChinaQ703 0TR390609FA FAIRCHILD KST3906-MTF TP SOTQ704 0TR390609FA FAIRCHILD KST3906-MTF TP SOTQ803 0TR127309AA KTA1273 TP KEC TO92 -Y(KTA96U802 0TFVI80067A SI3865BDV(E3) VISHAY R/TP TS

R201 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TPR202 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TPR203 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TPR207 0RJ3900D677 390 OHM 1/10 W 5% 1608 R/TPR208 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TPR209 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TPR210 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TPR216 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR217 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR220 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR240 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TPR501 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR503 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR506 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR508 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR519 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR520 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR521 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP

REPLACEMENT PARTS LIST

CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.

* NOTE : S SAFETY MarkAL ALTERNATIVE PARTS

MAIN BOARDCAPACITORS

DIODEs

ICs

TRANSISTOR

RESISTORs

Page 25: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

DATE: 2005. 12. 16. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION

R522 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR523 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR530 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TPR534 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR535 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TPR537 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TPR543 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR544 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR545 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TPR547 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TPR548 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TPR549 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TPR555 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TPR557 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TPR560 0RJ4702D677 47000 OHM 1/10 W 5% 1608 R/TR701 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TPR702 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TPR703 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TPR704 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TPR706 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TPR708 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TPR709 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TPR712 0RJ0102D677 10 OHM 1/10 W 5% 1608 R/TPR716 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR717 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR722 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TPR723 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TPR724 0RJ0332D677 33 OHM 1/10 W 5% 1608 R/TPR726 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TPR727 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TPR735 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR737 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR744 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR747 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR749 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR751 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TPR752 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TPR753 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TPR754 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TPR755 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TPR770 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR771 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR778 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TPR779 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TPR781 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TPR802 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR808 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TPR814 0RJ2202D677 22K OHM 1/10 W 5% 1608 R/TPR815 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TPR816 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TPR823 0RX0470J609 0.47 OHM 1 W 5% TA52R824 0RJ0272D677 27 OHM 1/10 W 5% 1608 R/TPR825 0RJ2000D677 200 OHM 1/10 W 5% 1608 R/TP

X501 6212AA2004A HC-49U TXC 12.0MHZ +/- 30 PP

C1 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7RC2 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R

DATE: 2005. 12. 16. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION

LED1 0DLLT0208AA LITEON LTST-C155KGJSKT R/TPR1 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR2 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPR3 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TPR4 0RJ2001D677 2K OHM 1/10 W 5% 1608 R/TPR5 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TPSW1 6600TR1002A SKQGACE010 J-ALPS NON 12V 50SW2 6600TR1002A SKQGACE010 J-ALPS NON 12V 50SW3 6600TR1002A SKQGACE010 J-ALPS NON 12V 50SW4 6600TR1002A SKQGACE010 J-ALPS NON 12V 50SW5 6600TR1002A SKQGACE010 J-ALPS NON 12V 50ZD1 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"ZD2 0DZ560009GB "BZT52C5V6S-(F),LF DIODES R/T"

- 22 -

OTHERs

CONTROL BOARD

Page 26: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 23 -

SCHEMATIC DIAGRAM

1. TSU56AL / TSU16AL

1

Wavefo

rms

U201-#96, 97

3R

216, R778 H

-Sync

3R

217, R781 V

-Sync

1

3

Page 27: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 24 -

2. MICOM

2U

501-#43 H-S

YN

C2

U501-#44 V

-SY

NC

Wavefo

rms

2

Page 28: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 25 -

3.POWER

Page 29: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

- 26 -

4. CONNECTOR & JACKS

3

Wavefo

rms

R216, R

778 H-S

ync3

R217, R

781 V-S

ync

3

Page 30: Esquema Lg Tft-lcd Color Monitor Flatron l1550s-Snn, l1550s- Bnn

Dec. 2005P/NO : 3828TSL094N Printed in Korea