Fischer Fbn Anchors

1

2

3

HIGH PERFORMANCE STEEL ANCHORS

fischer Bolt FBNThe flexible anchor – for economical performance.

32

fischer Bolt FBN,zinc plated and passivated steelfischer Bolt FBN with large washer,zinc plated and passivated steelfischer Bolt FBN, A4 stainless steel*fischer Bolt FBN fvz (hot dipped galvanized)*

* not included in approval notice.

4

3

2

1

Installation diagram

Approvals

Suitability

Suitable for:

Concrete so ≥ B15, natural stone with dense structure.

For fixing of:

Metal constructions, metal profiles, sole plates, brackets,railings, windows, gratings, machines, timber constructions(large washer), beams, purlins, supports etc.

Description

The fischer FBN bolt is a more advanced development of theFB and now offers even more scope for application. Inconcrete terms, this means that the FBN can be installedwith a variable embedment depth, i.e. the user has thechoice between the standard embedment depth withmaximum permitted load and an extended useful length witha reduced permitted load. The thread has been extendedwith this in mind.

Installation instructions

� Before tapping in, place the nut in the best position forinstallation (bolt projects approx. 2–3 mm).

� The letter engraved on the head of the anchor is requiredfor approval reasons and identifies the FBN in its installedstate.

Advantages

� Through its variable useful length (see description) and theextended thread, the FBN offers increased scope for use.

� The expansion clip has been improved, resulting in in-creased load values, even in low-quality concrete.

� Anchoring with the FBN is now even more economical.

� The FBN can be anchored with only a few turns.

� A special assortment with a large washer to DIN 440 isavailable for use with wood.

Fire resistanceclassification

F 90

4


fischer Bolt FBN

33

Technical data

Mean ultimate loads and recommended loads for single

anchors of fischer bolt FBN with large axial spacing and

edge distance

Non-cracked concrete

Anchor size M6 M8 M10 M12 M16 M20

Effective anchorage depth heff [mm] 40 35 48 42 50 50 70 64 84 100Drill hole depth h1 � [mm] 55 50 63 60 68 70 90 88 108 131Drill hole diameter do [mm] 6 8 8 10 10 12 12 16 16 20Mean ultimate loads Nu,m and Vu,m [kN]Tensile 0° Nu,m [kN] gvz – – 14.3* 19.2 22.4 25.6 35.0 35.0 47.1 70.1

[kN] fvz – – 15.5* – 20.9 – 35.2* – 47.1 –[kN] A4 10.6* – 16.4 20.5 30.5 30.5 39.9* 38.2 52.8 –

Shear 90° Vu,m [kN] gvz – – 11.3* 16.6* 16.6* 27.6 27.6* 33.4* 33.4* 71.4*[kN] fvz – – 12.3* – 19.1* – 27.6* – 33.4* –[kN] A4 9.0* – 15.1* 24.0* 24.0* 31.6* 31.6* 56.5* 56.5* –

Recommended loads Nrec and Vrec [kN]Tensile 0° Nrec [kN] gvz – 2.5 4.4 4.7 5.8 7.5 10.9 10.9 15.2 20.9

[kN] fvz – – 4.8 – 5.8 – 10.0 – 11.6 –[kN] A4 3.3 – 4.4 4.7 5.8 7.5 10.9 9.2 13.4 –

Shear 90° Vrec [kN] gvz – 3.2 5.3 5.8 7.5 7.5 12.9 16.9 16.9 36.5[kN] fvz – – 6.7 – 7.5 – 12.9 – 16.9 –[kN] A4 4.3 – 5.3 5.8 7.5 7.5 12.9 16.9 16.9 –

Recommended bending moment Mrec [Nm]Mrec [Nm] gvz – 10.5 10.5 21.4 21.4 40.5 40.5 96.0 96.0 194.6

[Nm] fvz – – 13.7 – 29.1 – 40.5 – 96.0 –[Nm] A4 6.5 14.7 14.7 29.7 29.7 46.9 46.9 114.3 114.3 –

Component dimensions, minimum axial spacings and edge distancesMin. axial spacing1) smin [mm] gvz – 35 50 45 55 100 75 140 90 170

fvz – – 50 – 55 – 130 – 85 –A4 40 – 50 50 60 65 80 90 90 –

Min. edge distance1) cmin [mm] gvz – 35 50 55 65 100 90 100 105 150fvz – – 50 – 65 – 100 – 80 –A4 35 – 35 60 55 70 75 80 80 –

Min. structural component thickness hmin [mm] 100 100 100 100 100 100 140 130 170 200

Required torque Tinst [Nm] 7.5 15 15 30 30 50 50 100 100 200

* steel failure1) For min. axial spacing and min. edge distance the above described loads have to be reduced!

(See “Technical Handbook” or design software “CC-Compufix”)

All load values apply for: concrete compressive strength fc,200 = 30 N/mm2

no edge or spacing influences.Recommended loads: material safety factors γM and safety factor for load γL = 1.4 are included.

Material safety factor γM depends on type of anchor.

The conditions of application differ from those given in the European Technical Approval. For further detailed information about European Technical Approvals please contact fischer technicalservice department.

FBN – fvz (hot dipped galvanized)

do td hef l tfix MMin.drill-hole Min.depth for Anchor- Max.

Steel Drill through age Overall fixing Qty.fvz* � fixing depth length thickness Thread per

Type Art. No. mm mm mm mm mm � x length pack

FBN 8x60 HDG* 57525 8 55 35 60 5 M 8 x 23 100FBN 8x75 HDG* 57526 8 73 48 75 10 M 8 x 41 50FBN 8x115 HDG* 57527 8 113 48 115 50 M 8 x 81 50FBN 8x165 HDG* 57528 8 163 48 165 100 M 8 x 130 25FBN 10x70 HDG* 57529 10 65 42 70 5 M10 x 31 50FBN 10x90 HDG* 57530 10 83 50 90 15 M10 x 51 50FBN 10x125 HDG* 57531 10 118 50 125 50 M10 x 87 20FBN 10x175 HDG* 57532 10 168 50 175 100 M10 x 134 20FBN 10x215 HDG* 57533 10 208 50 215 140 M10 x 174 20FBN 12x85 HGD* 57534 12 75 50 85 5 M12 x 41 20FBN 12x115 HDG* 57535 12 105 70 115 15 M12 x 71 20FBN 12x130 HDG* 57536 12 120 70 130 30 M12 x 86 20FBN 12x145 HDG* 57537 12 135 70 145 45 M12 x 103 20FBN 12x200 HDG* 57538 12 190 70 200 100 M12 x 157 20FBN 16x110 HDG* 57539 16 98 64 110 10 M16 x 54 10FBN 16x145 HDG* 57540 16 133 84 145 25 M16 x 89 10FBN 16x170 HDG* 57541 16 158 84 170 50 M16 x 114 10FBN 16x220 HDG* 57542 16 208 84 220 100 M16 x 166 10

* Not included in approval notice.

FBN – with large washer according to DIN 440, outside diameter approx. 3.5 x d

do td hef l tfix MMin.drill-hole Min.

Im- depth for Anchor- Max.print Drill through age Overall fixing Qty.on � fixing depth length thickness Thread per

Type head Art. No. mm mm mm mm mm � x length pack

FBN 12x180 GS N 45160 12 170 70/50 180 80/100 M12 x 137 20FBN 12x200 GS P 45161 12 190 70/50 200 100/120 M12 x 157 20FBN 12x220 GS R 45162 12 210 70/50 220 120/140 M12 x 177 20FBN 12x240 GS S 45163 12 230 70/50 240 140/160 M12 x 100 10FBN 12x260 GS T 45164 12 250 70/50 260 160/180 M12 x 100 10FBN 12x300 GS V 45165 12 290 70/50 300 200/220 M12 x 100 10FBN 12x350 GS W 45166 12 340 70/50 350 250/270 M12 x 100 10FBN 16x220 GS P 45167 16 208 84/64 220 100/120 M16 x 166 10FBN 16x260 GS S 45168 16 248 84/64 260 140/160 M16 x 100 10FBN 16x280 GS T 45169 16 268 84/64 280 160/180 M16 x 100 10FBN 16x320 GS V 45170 16 308 84/64 320 200/220 M16 x 100 10FBN 16x370 GS W 45171 16 358 84/64 370 250/270 M16 x 100 10FBN 16x420 GS X 45172 16 408 84/64 420 300/320 M16 x 100 10

1) Min. embedment depth for maximum permitted load/the minimum embedment depth can bereduced to . . . for the extended effective length and reduced load.

2) Embedment length for maximum permissible load/embedment length for reduced load.

FBN – zinc plated and passivated steel FBN – A4 stainless steel

do td hef l tfix MMin.drill-hole

Im- depth for Min. Max.print Steel Steel Drill through anchorage Overall- fixing Qty.on gvz A4* � fixing depth length thickness Thread per

Type head Art. No. Art. No. mm mm mm mm mm � x length pack

FBN 6x40* – 45130 – 6 45 20 40 5 M 6 x 16 100FBN 6x55* – 45136 – 6 50 25 55 10 M 6 x 30 100FBN 6x70 – – 69087 6 65 40 70 10 M 6 x 25 100FBN 6x75* – 45137 – 6 70 25 75 30 M 6 x 30 100FBN 6x90 – – 69088 6 85 40 90 30 M 6 x 30 100FBN 8x60 – 45131 – 8 55 35 60 5 M 8 x 23 100FBN 8x75 B 45138 69089 8 73 48/35 75 10/23 M 8 x 41 50FBN 8x95 F 45139 69090 8 93 48/35 95 30/43 M 8 x 61 50FBN 8x115 K 45140 69091 8 113 48/35 115 50/63 M 8 x 81 50FBN 8x165 P 45141 – 8 163 48/35 165 100/113 M 8 x 130 25FBN 10x70 – 45132 – 10 65 42 70 5 M10 x 31 50FBN 10x90 C 45142 69092 10 83 50/42 90 15/23 M10 x 51 50FBN 10x110 G 15399 – 10 103 50/42 110 35/43 M10 x 71 50FBN 10x125 K 45143 69093 10 118 50/42 125 50/58 M10 x 87 20FBN 10x175 P 45144 69094 10 168 50/42 175 100/108 M10 x 134 20FBN 10x215 S 45145 – 10 208 50/42 215 140/148 M10 x 174 20FBN 10x235 T 45146 – 10 228 50/42 235 160/168 M10 x 194 20FBN 12x85 – 45133 – 12 75 50 85 5 M12 x 41 20FBN 12x115 C 45147 69095 12 105 70/50 115 15/35 M12 x 71 20FBN 12x130 F 45148 – 12 120 70/50 130 30/50 M12 x 86 20FBN 12x145 I 45149 69096 12 135 70/50 145 45/65 M12 x 103 20FBN 12x200 P 45150 69097 12 190 70/50 200 100/120 M12 x 157 20FBN 16x110 – 45134 69098 16 98 64 110 10 M16 x 54 10FBN 16x145 E 45151 69099 16 133 84/64 145 25/45 M16 x 89 10FBN 16x170 K 45152 69100 16 158 84/64 170 50/70 M16 x 114 10FBN 16x220 P 45153 – 16 208 84/64 220 100/120 M16 x 166 10FBN 20x120* – 45135 – 20 111 70 120 10 M 20 x 50 10FBN 20x165 – 45154 – 20 151 100 165 20 M 20 x 50 10FBN 20x205 – 45155 – 20 191 100 205 60 M 20 x 90 10FBN 20x265 – 45156 – 20 251 100 265 120 M 20 x 90 10FBN 20x395 – 45157 – 20 381 100 395 250 M 20 x 90 5

* not included in approval notice.

34


fischer Anchor bolt FAThe economical through bolt thats re-usable ideal for stadium seating

Suitability

Suitable for:

concrete ≥ B15 and dense natural stone.

For fixing:

Railings, hand rails, seating, stock pens, gratings, supports,consoles, machines, metal constructions, metal profiles.

Description

� For through fixing.

� Torque controlled, safe expansion.

� Highest reliability.

� Demountable fixing leaving a flush surface

� Domed nut for neat appearance

� Red knurled collar prevents turning in hole on installation

� The expansion sleeve guarantees an even, calibrated

hold and depth in all compact materials

� The reduced diameter and practical installation make it

ideal for a quick, secure job

fischerbolt FA1

1

Ultimate loads Fu, m [kN] (mean values) and recommended loads Frec

[kN] for a single anchor in non-cracked concrete

Anchor type/thread FA 8 FA 10 FA 12 FA 14Fu, m B25 1280 1540 2030 2540

Frec B25 250 350 450 600

Axial spacing (cm) 16 24 26 40

Edge distance (cm) 8 10 13 15

Min. component thickness (cm) 15 15 20 20


FA – zinc plated and passivated, with hexagon domed nutdo td hv l da Mc SW

Min. drill-hole Min. Max.depth for anchor- fixing

Drill through age Fixing thick- Width QtyÆ fixing depth length ness Torque across per

Type Art. No. mm mm mm mm mm Nm nutpack

FA 8/15 ( 8 x 70) 50200 8 75 50 65 15 10 13 25

FA 8/25 ( 8 x 85) 50207 8 90 50 80 25 10 13 25

FA 10/15 (10 x 85) 50201 10 90 60 75 15 20 17 25

FA 10/50 (10 x 120) 50208 10 120 60 110 50 20 17 25

FA 12/15 (12 x 100) 50202 12 100 70 85 15 35 19 20

FA 12/50 (12 x 135) 50212 12 135 70 120 50 35 19 20

FA 14/20 (14 x 115) 50203 14 115 80 100 20 50 22 10

FA 14/50 (14 x 145) 50214 14 145 80 130 50 50 22 20

35

For your notes


fischer Concrete screw FBSSafe form fit through special thread.

36


Approvals

Concrete screw FBS 8 + 10Concrete screw FBS 10 A4Concrete screw FBS 5 + 6

Z-21.1-1717Z-21.1-1716Z-21.1-1718

Fire resistanceclassificationF 90/120

Suitability

Suitable for:

Concrete ≥ B15 and masonry building materials.

For fixing of:

Installation rails, ventilation ducts, pipework, suspended ceilings, metal profiles, wood sub-structures,facade sub-structures, shelf feet. Also suitable for temporaryfastenings such as wall shuttering.

Description

fischer concrete screws have a specially hardened thread.The lower turns of the thread also have teeth. The diameterof the hole and the thread of the screw are adapted to oneanother so that the special thread of the screw cuts into theconcrete. The thread turns creating a fine undercut, therebyensuring that the load is safely supported by a perfect formfit. The teeth allow the thread to cut into the concrete,thereby reducing the amount of energy required to insert thescrew into its position.

Panhead (P)Countersunk head (SK)Hexagon with integrated washer (US)

3

2

1 Hexagon (S)External thread (M8)Internal thread (M8/M10)6

5

4

1

2

3

4

5

6

Advantages

� Fast installation by simply screwing the screw into thehole in the concrete.

� Fully detachable screw attachment.

� High permissible loads through safe form fit.

� Minimum edge and axial distances through absence ofexpansion pressure.

� Variable application through different head shapes.

NEW

Mean ultimate loads and recommended loads for single anchors of fischer concrete screw FBS

with large axial spacing and edge distance

Non-cracked concrete Cracked concrete

Anchor size FBS 8 FBS 10 FBS 5* FBS 6* FBS 8 FBS 10

Effective anchorage depth heff [mm] 50 60 55 55 50 60Drill hole depth ho � [mm] 85 95 60 60 85 95

Screw-in depth hnom � [mm] 75 85 – – 75 85

Drill hole diameter do [mm] 8 10 5 6 8 10

Mean ultimate loads Nu,m and Vu,m [kN]Tensile 0° Nu,m [kN] gvz 21.2 26.4 1.2 3.2 10.0 16.0

[kN] A4 – 26.4 – – – 16.0

Shear 90° Vu,m [kN] gvz 29.6 48.4 – – 29.6 48.4[kN] A4 – 54.4 – – – 54.4

Recommended loads Nrec and Vrec [kN]Tensile 0° Nrec [kN] gvz 5.3 6.6 0.3 0.8 2.5 4.0

[kN] A4 – 6.6 – – – 4.0

Shear 90° Vrec [kN] gvz 7.4 12.1 – – 7.4 12.1[kN] A4 – 13.6 – – – 13.3

Recommended bending moment Mrec [Nm]Mrec [Nm] gvz 19.0 40.0 – 8.0 19.0 40.0

[Nm] A4 – 36.8 – – – 36.8

Component dimensions, minimum axial spacings and edge distancesMin. axial spacing1) smin [mm] 50 60 50 50 50 60

Min. edge distance1) cmin [mm] 60 65 100 100 60 65

Min. structural component thickness hmin [mm] 120 130 110 110 120 130

* For the fixing of lightweight suspended ceiling constructions only.1) For min. axial spacing and min. edge distance the above described loads have to be reduced! (See “Technical Handbook” or design software “CC-Compufix”)


no edge or spacing influences.Recommended loads: material safety factors γM and safety factor for load γL = 1.4 are included. Material safety factor γM depends on type of anchor.

The conditions of application differ from those given in the German approval.

For further detailed information about German approval please contact fischer technical service department.


fischer Concrete screw FBS

37

Installation exampleTechnical data

do df ds td hnom tfix L = Min. hnom + tfixdrill-hole

Drill- depth for Min. Max.hole � push- Screw- fixingin Screw through in thick- Screw Qty.

Drill � object outer � installation depth ness length perType Art. No. mm mm mm mm mm mm mm Drive pack

zinc plated

FBS 5/5 P 66774 5 7 6.5 65 55 5 60 T30 100

FBS 6/5 SK 66935 6 8 7.6 65 55 5 60 T30 100

FBS 6/5 P 66939 6 8 7.6 65 55 5 60 T30 100

FBS 6/25 P 66948 6 8 7.6 85 55 25 80 T30 100

FBS 6 M8 66949 6 – 7.6 60 55 – 55 SW10 100

FBS 6 M8/M10I 66950 6 – 7.6 60 55 – 55 SW13 100

FBS 8/5 US 66956 8 12 10.5 90 75 5 80 T40/SW13 100

FBS 8/25 US 66957 8 12 10.5 110 75 25 100 T40/SW13 100

FBS 8/15 S 66958 8 12 10.5 100 75 15 90 SW16 100

FBS 10/5 S 67062 10 14 12.5 100 85 5 90 SW18 50

FBS 10/15 S 67063 10 14 12.5 110 85 15 100 SW18 50

FBS 10/25 S 67168 10 14 12.5 120 85 25 110 SW18 50

A4 stainless steel

FBS 10/10 S A4 67169 10 14 12.5 105 85 10 95 SW17 50

1

2


fischer Sleeve anchor FSAThe economical through bolt for all applications not requiring Approvals.

38

∅ do

td dahv

MD

M

l

Suitability

Suitable for:

Concrete ≥ B15 and natural stone with dense structure.

For fixing of:

Railings, handrails, gratings, supports, consoles, machines,metal constructions, metal profiles etc.

Description

The fischer Sleeve anchor FSA is a torque controlled expand-ing steel anchor for all through fixings for light and mediumloads.Unlike ordinary sleeve anchors, the geometry of the expan-sion sleeve and the cone has been improved and the com-bined effect of these two functional elements optimised.This guarantees full expansion in all cases, thus providingoptimum safety and reliability at the high level you expect offischer.

The FSA is available in 2 versions:

� FSA-S with hexagon screw and cone nut

Sleeve anchor FSA-S Sleeve anchor FSA

Material: zinc plated and passivated steel.

2

1


Advantages

� The simple design and construction result in an excellentcost-performance ratio.

� The computer optimised anchor cone and the suitablyadjusted expansion sleeve result in a safe expansion.

� The crescent-shaped punch-outs enable the sleeve toneatly slide together on the axis when bridging hollowlayers. The assembly object braces tightly against thebuilding material.

� The setting depth mark allows verification of the correctinstallation any time.

� The setting head at the runout of the conical bolt preventdamage to the thread. In the case of de-mounting, an easythread travel is always ensured.

Picture for illustration purposes only


fischer Sleeve anchor FSA

39

FSA-S – zinc-plated and passivated steel, with hexagon screw and cone nut

do td hv l da M SWMin.drill-hole Min. Max.depth for anchor- fixing

Drill through age Fixing thick- Width Qty.� fixing depth length ness across per

Type Art. No. mm mm mm mm mm Thread nut pack

FSA 8/15 S 68520 8 65 35 69 15 M 6 10 50

FSA 8/40 S 68521 8 90 35 94 40 M 6 10 50

FSA 8/65 S 68522 8 115 35 119 65 M 6 10 50

FSA 10/10 S 68523 10 65 40 70 10 M 8 13 20

FSA 10/35 S 68524 10 90 40 95 35 M 8 13 20

FSA 10/60 S 68525 10 115 40 120 60 M 8 13 20

FSA 12/10 S 68526 12 75 50 81 10 M10 17 20

FSA 12/25 S 68527 12 90 50 96 25 M10 17 20

FSA 12/50 S 68528 12 115 50 121 50 M10 17 20

FSA-A2 – Stainless Steel A2, with conical bolt and hexagon nut




FSA 8/45 A2 60250 8 60 25 45 10 M 6 10 100

FSA 8/65 A2 60251 8 80 30 65 25 M 6 10 50

FSA 10/50 A2 60252 10 65 30 50 10 M 8 13 50

FSA 10/70 A2 60253 10 85 35 70 25 M 8 13 50

FSA 10/100 A2 60254 10 115 35 100 55 M 8 13 50

FSA 10/120 A2 60255 10 135 35 120 75 M 8 13 50

FSA 12/60 A2 60256 12 80 35 60 10 M10 17 25

FSA 12/80 A2 60257 12 100 40 80 25 M10 17 25

FSA 12/100 A2 60258 12 120 40 100 45 M10 17 20

FSA 12/120 A2 60259 12 140 40 120 65 M10 17 20

FSA – zinc-plated and passivated steel, with conical bolt and hexagon nut




FSA 6/5 60168 6 35 20 25 5 M 4.5 8 100

FSA 6/8 60156 6 48 30 38 8 M 4.5 8 100

FSA 6/25 60157 6 68 33 58 25 M 4.5 8 100

FSA 8/8 60158 8 57 34 42 8 M 6 10 100

FSA 8/30 60150 8 81 36 66 30 M 6 10 100

FSA 8/55 60159 8 107 37 92 55 M 6 10 100

FSA 10/10 60160 10 63 38 48 10 M 8 13 50

FSA 10/35 60151 10 90 40 75 35 M 8 13 50

FSA 10/60 60152 10 115 40 100 60 M 8 13 50

FSA 12/12 60161 12 73 46 58 12 M10 17 25

FSA 12/20 60153 12 85 50 70 20 M10 17 25

FSA 12/50 60154 12 115 50 100 50 M10 17 20

FSA 12/75 60162 12 140 50 125 75 M10 17 20

FSA 16/12 60163 16 84 52 64 12 M12 19 20

FSA 16/50 60155 16 128 58 108 50 M12 19 10

FSA 16/80 60164 16 162 62 142 80 M12 19 10

FSA 20/20 60165 20 107 62 82 20 M16 24 10

FSA 20/50 60166 20 139 64 114 50 M16 24 5

FSA 20/95 60167 20 183 63 158 95 M16 24 5

Technical data

Installation examples

Mean ultimate loads and recommended loads for singleanchors of fischer Sleeve anchor FSA with large axialspacing and edge distance

Non-cracked concrete

Anchor size FSA 8/.. FSA 10/.. FSA 12..M 6 M 8 M 10

Effective anchorage depth heff [mm] 35 40 50Drill hole depth ho � [mm] 50 55 65Drill hole diameter do [mm] 8 10 12Mean ultimate loads Nu,m and Vu,m [kN]Tensile 0° Nu,m [kN] gvz 12.0 14.7 21.5Shear 90° Vu,m [kN] gvz 13.2* 18.7 26.1Recommended loads Nrec and Vrec [kN]Tensile 0° Nrec [kN] gvz 2.8 3.7 4.5Shear 90° Vrec [kN] gvz 5.1 6.2 8.7Recommended bending moment Mrec [Nm]

Mrec [Nm] gvz 5.2 12.9 25.7Component dimensions, minimum axial spacings and edge distancesMin. axial spacing1) smin [mm] 70 80 100Min. edge distance1) cmin [mm] 50 60 60Min. structural comp. thickness hmin [mm] 70 80 100Required torque Tinst [Nm] 10 25 40

* steel failure1) For min. axial spacing and min. edge distance the above described loads have to be reduced!





For detailed design method please contact fischer technical service department.

Picture for illustration purposes only

1


fischer Hollow-ceiling anchor FHYSpecially for fixings in hollow-ceiling slabs.

40

Suitability

Suitable for: Hollow-ceiling slabs of prestressed concrete, concrete ≥ B55.

For fixing of: All types of anchoring, e.g. cross beams, pipesand ventilation ducts, suspended ceilings, safety engineering,cable trays.

Description

The fischer Hollow-ceiling anchor FHY has been developedspecially for fastenings in hollow-ceiling slabs of prestressedconcrete. It is designed for use with standard bolts or threaded rods with metric threads from M6 to M10.The Hollow-ceiling anchor FHY is installed flush with theconcrete surface. When the bolt or the nut is tightened atapered element is pulled into the sleeve, which presses thisoutwards. In this way, the FHY presses against the sides ofthe hole, creating a friction fit. If the anchor encounters acavity during installation, the expansion of the sleeve forms aY shape. The holding power is now the result of acombination of expansion pressure and form-fit.The fischer Hollow-ceiling anchor FHY offers considerablescope in the location of attachment points. Unlike othercompeting products, it does not have to be located at thecentre of the cavity axis, which is often very difficult todefine. Instead, it can be located down to a minimumdistance of 50 mm from the prestressing steel.

Installation advice

How to determine the length of the screw ls:

length of the fischer Hollow-ceiling anchor FHY(+ thickness of the building component da

(= length of the screw(+ additional thickness of nut and washer withthreaded rods)

Hollow-ceiling anchor FHY

Material: zinc plated steel and A4 stainless steel

1


Approvals

Approval is valid forzinc plated steel.

Z-21.1-1711

t fix

l s

h ef

do

TinstFire resistanceclassification

F 120

Recommended loads1) fixing parameters and component dimensions for ten-sion, shear and diagonal load at any angle in hollow-slab floors of prestressedconcrete of strength class ≥ B55 or ≥ C50/60. When dimensioning, observethe approval Z-21.1-1711 in its entirety.

Fixing type FHY M 6 FHY M 8 FHY M 10

Web thickness du mm ≥ 25 ≥ 30 ≥ 40 ≥ 25 ≥ 30 ≥ 40 ≥ 30 ≥ 40< 30 < 40 < 30 < 40 < 40

Drill hole depth h1 ≥ mm 50 60 65Drill hole diameter mm 10 12 16Single fixingPerm. F2) with c ≥ ccr1.2 kN 0.7 0.9 2.0 0.7 0.9 2.0 1.2 3.0Perm. F2) with c = cmin1.2 kN 0.35 0.8 1.8 0.35 0.8 1.8 1.0 2.7Axial spacing2) ccr1.2 ≥ mm 150Min. edge distance2) cmin1.2 ≥ mm 100Axial spacing scr1.2 ≥ mm 300Pairs of fixings3)

Perm. F with c ≥ ccr1.2 kN 0.7 1.4 2.6 0.7 1.4 2.6 2.0 4.8Perm. F with c = cmin kN 0.35 1.25 2.35 0.35 1.25 2.35 1.8 4.3Min. axial spacing smin1.2 ≥ mm 70 80 100 70 80 100 80 100Edge distance ccr1.2 ≥ mm 150Min. edge distance cmin1.2 = mm 100Safe working bending momentGrade 4.6 Nm – 6.4 12.8Grade 5.8 Nm 4.44) 10.74) 21.44)

Grade 5.8 Nm 7.04) 17.14) 34.24)

Length of hexagon-head min ls ≥ mm 39 + tfix 45 + tfix 54 + tfixscrew5)

Length of threaded bolt min lB ≥ mm 62 + tfix 68 + tfix 77 + tfixInstallation torque TInst Nm 10 10 20Through-hole in the component to be attached df ≤ mm 7 9 12

1) The anchorage of the Cavity Fixing FHY is permissible only in hollow-slab ceilings of prestressed concrete,the width of whose cavities is not more than 4.2 times the web width. The fixing may also be used as multiple fastening for anchoring lightweight ceiling coverings and underceilings to DIN 18168 on hollow-slab ceilings of prestressed concrete, and for statically similar anchorages up to 1.0 kN/m2. When external loads are suspended from the prestressed-concrete hollow-slab ceilings, the shearing load-bearing capacity must be reduced. For fastening lightweight ceiling coverings and underceilings,to DIN 18168, this reduction is not necessary.

2) For edge distances cmin < c�ccr the permissible loads may be determined by linear interpolation.3) The permissible load applies for a pair of fixings. The permissible load for the most highly stressed fixing must

not exceed the values stated for the single fixing. For pairs of fixings with min axial distances of smin1.2 < s1.2 < scr1.2 the permissible load may be interpolatedlinearly. The linear value at s1.2 = scr1.2 for the pair of fixings with tensile load applied, may be assumed to betwice the permissible load for the single fixing.

4) Only threaded rods marked in accordance with the approval may be used.5) With hexagon bolts with shaft to DIN EN 24014, the shaft length must be ≤ tfix.


fischer Hollow-ceiling anchor FHY

41

Technical data Installation examples

FHY – zinc plated steel

do h1* hef 1) lMin. Min.drill- anchor- Screw-in

Drill hole age Fixing depth Qty.� depth depth length min. max.* per.

Type Art. No. mm mm mm mm Thread mm mm pack

FHY M 6 30138 10 50 30 37 M 6 37 45 50

FHY M 8 30146 12 60 35 43 M 8 43 55 25

FHY M 10 30148 16 65 40 52 M 10 52 60 20

FHY – A4 stainless steel (Material: 1.4401)

do h1* hef 1) lMin. Min.drill- anchor- Screw-in

Drill hole age Fixing depth Qty.� depth depth length min. max.* per.

Type Art. No. mm mm mm mm Thread mm mm pack

FHY M 6 A4 30139 10 50 30 37 M 6 37 45 50

FHY M 8 A4 30147 12 60 35 43 M 8 43 55 25

FHY M 10 A4 30151 16 65 40 52 M 10 52 60 20

* in solid materials

42


fischer Wallbolt GMThe economical heavy-duty anchor


Suitability

Suitable for:


For fixing of:

Installation rails, ventilation ducts, pipework, suspendedceilings, metal profiles, shelf feet. Also suitable for temporaryfastenings such as wall shuttering

Description

The segmented malleable iron expansion shield isassembled ready for use with bolts or threaded rods of theappropriate diameter.

� Function - torque controlled friction locking expansion.

� Four piece malleable shield for even load spread.

� Unique metal spring clip for retaining the segments andthe wedge.

� Traditional fixing method with wide user acceptance.

� Zinc plated and passivated for corrosion protection.

For the best results with the GM anchor remember to:

� Choose the most suitable accessory.

� Choose the right sized anchor in relation to load type.

� Check load bearing capacity values in the table.

� Make sure the drilled hole is dust free.

GM S wallbolt - shield only

GM H wallbolt - hook bolt type

GM P wallbolt - projecting bolt type

GM L wallbolt - loose bolt type

GM E wallbolt - eye bolt type5

4

3

2

1

1

2

3

4

5

43


fischer Wallbolt GM

Technical data Technical data

Recommended loads [kN]

GM P – zinc plated and passivateddo td hv

Min.Min. anchor- Fixing

Drill drill-hole age Bolt Thickness Qty.Ø depth depth Ø mm Torque per

Type Art. No. mm mm mm mm min max Nm box

GM 6/10 P 58030 12 60 47 6 0 10 10 50

GM 6/25 P 58031 12 60 47 6 0 25 10 50

GM 6/60 P 58032 12 60 47 6 0 60 10 50

GM 8/10 P 58033 15 70 50 8 0 10 25 50

GM 8/25 P 58034 15 70 50 8 0 25 25 50

GM 8/60 P 58035 15 70 50 8 0 60 25 50

GM 10/15 P 58036 18 80 60 10 0 15 40 50

GM 10/30 P 58037 18 80 60 10 0 30 40 25

GM 10/60 P 58038 18 80 60 10 0 60 40 25

GM 12/15 P 58039 22 100 75 12 0 15 75 20

GM 12/35 P 58040 22 100 75 12 0 35 75 20

GM 12/75 P 58041 22 100 75 12 0 75 75 20

GM 16/15 P 58042 29 130 102 16 0 15 180 10

GM 16/35 P 58043 29 130 102 16 0 35 180 10

GM 16/75 P 58044 29 130 102 16 0 75 180 10

GM 20/15 P 58045 36 170 135 20 0 15 345 5

GM 20/30 P 58046 36 170 135 20 0 30 345 5

GM 20/100 P 58047 36 170 135 20 0 100 345 5

GM 24/75 P 58048 42 210 165 24 0 30 345 5

GM 24/120 P 58049 42 210 165 24 0 100 345 5

GM S – zinc plated and passivateddo td hv

Min.Min. anchor-

Drill drill-hole age Bolt Qty.Ø depth depth Ø Torque per

Type Art. No. mm mm mm mm Nm box

GM 6 S 58060 12 60 47 6 10 50

GM 8 S 58061 15 70 50 8 25 50

GM 10 S 58062 18 80 60 10 40 25

GM 12 S 58063 22 100 75 12 75 20

GM 16 S 58064 29 130 102 16 180 10

GM 20 S 58065 36 170 135 20 345 5

GM 24 S 58066 42 210 165 24 345 5

GM E – zinc plated and passivateddo td hv

Min.Min. anchor-

Drill drill-hole age Bolt Eye Qty.Ø depth depth Ø Ø Torque per

Type Art. No. mm mm mm mm mm Nm box

GM 6 E 58050 12 60 47 6 10.5 10 50

GM 8 E 58051 15 70 50 8 11 25 50

GM 10 E 58052 18 80 60 10 12.5 40 25

GM 12 E 58053 22 100 75 12 15.5 75 15

GM 16 E 58054 29 130 102 16 25 180 10

GM H – zinc plated and passivateddo td hv

Min.Min. anchor-

Drill drill-hole age Bolt Qty.Ø depth depth Ø Hook Torque per


GM 6 H 58055 12 60 47 6 7.5 10 50

GM 8 H 58056 14 70 50 8 10.5 25 50

GM 10 H 58057 16 80 60 10 13 40 25

GM 12 H 58058 20 100 75 12 15.5 75 15

GM 16 H 58059 29 130 102 16 21.5 100 10

Loads in concrete cl.fc = 25 Nm/mm2 - kN

Anchor type GM 6 GM 8 GM 10 GM 12 GM 16 GM 20 Bolts cl. 8.8 4.00 4.65 5.90 8.40 13.40 20.65

Eyebolt 3.20 4.65 5.90 8.40 - 13.40

Hook 0.90 1.30 1.90 3.30 - 2.90

Critical edge distance and critical spacing [mm]Crit. axial spacing a 140 170 200 250 315 400Crit. edge distance ar 40 105 120 150 200 260Min. axial sp.a min. 80 80 100 125 170 230Min. edge dist.armin. 50 50 65 80 105 140Min. struct. thickness t 100 100 100 125 175 230

GM L – zinc plated and passivateddo td hv




GM 6/10 L 58001 12 60 47 6 0 10 10 50

GM 6/25 L 58002 12 60 47 6 0 25 10 50

GM 6/40 L 58003 12 60 47 6 0 40 10 50

GM 8/10 L 58004 15 70 50 8 0 10 25 50

GM 8/25 L 58005 15 70 50 8 0 25 25 50

GM 8/40 L 58006 15 70 50 8 0 40 25 50

GM 10/10 L 58007 18 80 60 10 0 10 40 50

GM 10/25 L 58008 18 80 60 10 0 25 40 50

GM 10/50 L 58009 18 80 60 10 0 50 40 50

GM 10/75 L 58010 18 80 60 10 25 75 40 25

GM 12/10 L 58011 22 100 75 12 0 10 75 25

GM 12/25 L 58012 22 100 75 12 0 25 75 25

GM 12/50 L 58013 22 100 75 12 0 50 75 25

GM 12/75 L 58014 22 100 75 12 25 75 75 25

GM 16/15 L 58015 29 130 102 16 0 15 180 10

GM 16/30 L 58016 29 130 102 16 0 30 180 10

GM 16/60 L 58017 29 130 102 16 25 60 180 10

GM 20/60 L 58018 36 170 135 20 20 60 345 10

GM 20/100 L 58019 36 170 135 20 60 100 345 10

GM 24/100 L 58021 42 210 165 24 20 100 345 10

GM 24/150 L 58022 42 210 165 24 60 150 345 10


fischer Wallbolt FWBThe economical heavy-duty anchor

44


Installation instructions

Determination of the screw length ls:

length of the fischer Heavy-duty anchor FWB +thickness of the building component da

= length of the screw

(in the case of threaded bolts additionally include+ thickness of washer and nut)

Suitability

Suitable for:


For fixing of:

Installation rails, ventilation ducts, pipework, suspendedceilings, metal profiles, shelf feet. Also suitable for temporaryfixings such as wall shuttering

Description

The segmented steel expander shield is assembled readyfor use with bolts or threaded rods of the appropriatediameter.

� Function - torque controlled friction locking expansion.

� Three piece shield for even load spread.

� Traditional fixing method with wide user acceptance.

� Zinc plated and passivated for corrosive protection.

The versatile heavy-duty fixing !

1

2

3

4

5

FWB S wallbolt - shield only

FWB L wallbolt - loose bolt type

FWB P wallbolt - projecting bolt type

FWB H wallbolt - hook bolt type

FWB E wallbolt - eye bolt type5

4

3

2

1


fischer Wallbolt FWB

45

Technical data Technical data

Recommended loads [kN]

FWB P – zinc plated and passivateddo td hv




FWB 6/10 P 58175 12 50 45 6 0 10 10 50

FWB 6/25 P 58176 12 50 45 6 0 25 10 50

FWB 6/60 P 58177 12 50 45 6 0 60 10 50

FWB 8/10 P 58178 14 55 50 8 0 10 25 50

FWB 8/25 P 58179 14 55 50 8 0 25 25 50

FWB 8/60 P 58180 14 55 50 8 0 60 25 25

FWB 10/15 P 58181 16 65 60 10 0 15 40 50

FWB 10/30 P 58182 16 65 60 10 0 30 40 25

FWB 10/60 P 58183 16 65 60 10 0 60 40 25

FWB 12/15 P 58184 20 85 75 12 0 15 75 25

FWB 12/35 P 58185 20 85 75 12 0 35 75 25

FWB 12/75 P 58186 20 85 75 12 0 75 75 25

FWB 16/15 P 58187 25 130 115 16 0 15 180 10

FWB 16/35 P 58188 25 130 115 16 0 35 180 10

FWB 16/75 P 58189 25 130 115 16 0 75 180 10

FWB 20/15 P 58190 32 150 130 20 0 15 345 10

FWB 20/30 P 58191 32 150 130 20 0 30 345 10

FWB 20/100 P 58192 32 150 130 20 0 100 345 10

FWB S – zinc plated and passivateddo td hv

Min.Min. anchor-

Drill drill-hole age Bolt Qty.Ø depth depth Ø Torque per

Type Art. No. mm mm mm mm Nm box

FWB 6 S 58050 12 50 45 6 10 50

FWB 8 S 58051 14 55 50 8 25 50

FWB 10 S 58052 16 65 60 10 40 50

FWB 12 S 58053 20 85 75 12 75 25

FWB 16 S 58054 25 130 115 16 180 10

FWB 20 S 58055 32 150 130 20 345 10

FWB E – zinc plated and passivateddo td hv

Min.Min. anchor-

Drill drill-hole age Bolt Eye Qty.Ø depth depth Ø Ø Torque per


FWB 6 E 58193 12 50 45 6 10 10 50

FWB 8 E 58194 14 55 50 8 12 25 50

FWB 10 E 58195 16 65 60 10 14 40 25

FWB 12 E 58196 20 85 75 12 17 75 25

FWB 16 E 58197 25 130 115 16 23 180 10

FWB H – zinc plated and passivateddo td hv

Min.Min. anchor-

Drill drill-hole age Bolt Qty.Ø depth depth Ø Hook Torque per


FWB 6 H 58198 12 50 45 6 8 10 50

FWB 8 H 58199 14 55 50 8 10 25 50

FWB 10 H 58200 16 65 60 10 12 40 25

FWB 12 H 58201 20 85 75 12 16 75 25

For information relating to loads please contact the fischer technical

department. 01491 827920

FWB L – zinc plated and passivateddo td hv




FWB 6/10 L 58156 12 50 45 6 0 10 10 50

FWB 6/25 L 58157 12 50 45 6 0 25 10 50

FWB 6/40 L 58158 12 50 45 6 0 40 10 50

FWB 8/10 L 58159 14 55 50 8 0 10 25 50

FWB 8/25 L 58160 14 55 50 8 0 25 25 50

FWB 8/40 L 58161 14 55 50 8 0 40 25 50

FWB 10/10 L 58162 16 65 60 10 0 10 40 50

FWB 10/25 L 58163 16 65 60 10 0 25 40 50

FWB 10/50 L 58164 16 65 60 10 0 50 40 50

FWB 10/75 L 58165 16 65 60 10 25 75 40 25

FWB 12/10 L 58166 20 85 75 12 0 10 75 25

FWB 12/25 L 58167 20 85 75 12 0 25 75 25

FWB 12/40 L 58168 20 85 75 12 0 50 75 25

FWB 12/60 L 58169 20 85 75 12 25 75 75 25

FWB 16/15 L 58170 25 130 115 16 0 15 180 10

FWB 16/30 L 58171 25 130 115 16 0 30 180 10

FWB 16/60 L 58172 25 130 115 16 25 60 180 10

FWB 20/60 L 58173 32 150 130 20 20 60 345 10

FWB 20/100 L 58174 32 150 130 20 60 100 345 10

t = hv

Mdo

e

da

ls = da + e

MD

1


fischer Hammerset anchor EAThe simple hammerset anchor with internal thread.

46

Approved for the tensionzone, light suspendedceilings and ceilingcovers.

Hammerset anchor EA

Material: zinc plated and passivated steel, A4 stainless steel.

1

Approvals


From thread M10

Recognised foruse with fixed watersprinkler systemsfrom M8.

Suitability

Suitable for: Concrete ≥ B15

For fixing of:

Flat steel, profiled steel, pipelines, suspended ceilings, ventilation pipes, sprinkler systems, threaded rods, assemblysupport, gratings, facades, diamond drilling devices (EA-D),etc.

Description

The fischer Hammerset anchor EA is a compact internallythreaded fixing for attachment assembly, made of zincplated steel for metric threads M 6 to M 20. The sizes M 6 toM 16 are also available in stainless steel. It is universallyeasy to use and offers the following:

� Economical fixing

� Shallow drill-hole depth

� displacement controlled impact expansion

� favourable ratio of thread/drill-hole diameter

The fischer Hammerset anchor EA forms a flush seal withthe concrete surface and permits replacement of the mount-ed item without influencing the expansion force. The settingmethod of ’tapping in’ and price/performance ratio havemade the EA anchor a standard metal fixing most acousticsinstallers, heating, ventilation and sanitary equipmentinstallers, metal constructors and fitters

Installation advice

� It is essential to adhere to the drill-hole depth and drilldiameter.

� The cone must only be driven with the setting tool EAWH(narrow-end) into the anchor sleeve.

� The cone must be driven into the anchor sleeve until thetool collar lies on the anchor body.

The screw length must be carefully determined:

min. screw-in depth+ thickness of the building component

= screw length

(with threaded bolt, include thickness of washer and nut)

If the screw is too long:

No tighteneing of the fixing is possible, since screw reachesend of thread.

If the screw is too short:

Thread load-bearing capacity too low.

Dossier NPO.021EA M 8 x 40M 10, M 12

Z-21.1-1619

Fire resistanceclassification

F 120


fischer Hammerset anchor EA

47

EA – zinc plated and passivated steel not suitable for diamond drilling devices and diamond saws

do t hv l MMin. Min.drill-hole anchorage Fixing Screw-in depth

Drill � depth depth lenght min. max. QuantityType Art. No. mm mm mm mm Thread mm mm per pack

EA M 61) 60811 8 25 25 25 M 6 6 12 100EA M 8 60812 10 30 30 30 M 8 8 13 100EA M 8 x 40 60821 10 40 40 40 M 8 8 20 50EA M 10 60813 12 40 40 40 M 10 10 17 50EA M 12 60814 15 50 50 50 M 12 12 22 25EA M 16 60816 20 65 65 65 M 16 16 27 20EA M 20 60818 25 80 80 80 M 20 20 34 10

EA – A4 stainless steel (material: 1.4401), not suitable for diamond drilling devices and diamond saws

EA M 6 A41) 60825 8 25 25 25 M 6 6 12 100EA M 8 A41) 60826 10 30 30 30 M 8 8 13 100EA M 10 A4 60827 12 40 40 40 M 10 10 17 50EA M 12 A4 60828 15 50 50 50 M 12 12 22 25EA M 16 A4 60829 20 65 65 65 M 16 16 27 20

1) only part of the approval for light suspended ceilings . . .

Hammerset tools

EAW H 6 60836 Fits EA M 6 1EAW H 8 60837 Fits EA M 8 1EAW H 8 x 40 60846 Fits EA M 8 x 40 1EAW H 10 60838 Fits EA M 10 1EAW H 12 60839 Fits EA M 12 1EAW H 16 60841 Fits EA M 16 1EAW H 20 60843 Fits EA M 20 1

Mean ultimate loads and recommended loads for single anchors of fischer Hammerset anchor EA with large axial

spacing and edge distance

Non-cracked concrete Cracked concrete1)

Anchor size M6 M8 M8 x 40 M10 M12 M16 M20 M6 M8 M8 x 40 M10 M12

Effective anchorage depth heff [mm] 25 30 40 40 50 65 80 25 30 40 40 50Drill hole depth h1 = [mm] 27 33 43 44 54 71 86 27 33 43 44 54Drill hole diameter do [mm] 8 10 10 12 15 20 25 8 10 10 12 15Mean ultimate loads Nu,m and Vu,m [kN]Tensile 0° Nu,m [kN] gvz 10.1* 14.0 16.3 18.6 32.0 40.0 66.0 – – – – –

[kN] A4 12.0 14.0 – 18.6 32.0 40.0 – – – – – –Shear 90° Vu,m [kN] gvz 6.0* 10.2* 10.2* 11.7* 21.2* 31.4* 50.3* – – – – –

[kN] A4 8.1* 9.8* – 12.4* 22.5* 36.8* – – – – – –Recommended loads Nrec and Vrec [kN]Tensile 0° Nrec [kN] gvz 2.3 3.0 4.0 4.5 6.5 9.5 13.0 0.5 0.5 0.8 0.8 0.8

[kN] A4 2.3 3.0 – 4.5 6.5 9.5 – 0.5 0.5 0.8 0.8 0.8Shear 90° Vrec [kN] gvz 2.9 4.8 4.8 5.6 10.2 12.4 20.0 – – – – –

[kN] A4 3.2 3.9 – 4.8 8.8 14.4 – – – – – –Recommended bending moment Mrec [Nm], values apply to screws with a strength classification 5.6 and A4-70 respectively

Mrec [Nm] gvz 3.3 8.0 8.0 16.0 28.1 71.4 139 – – – – –[Nm] A4 4.9 12.1 12.1 24.1 42.1 107 – – – – – –

Component dimensions, minimum axial spacings and edge distancesMin. axial spacing2) smin [mm] 70 80 100 100 140 170 200 400 400 400 400 400Min. edge distance2) cmin [mm] 80 90 120 120 150 220 240 100 100 100 200 200Min. structural component thickness hmin [mm] 100 100 120 120 150 200 240 100 100 100 100 100Required torque Tinst [Nm] 4 8 8 15 35 60 120 2 3 3 6 15

* steel failure, values apply to screws with a strength classification 5.6 and A4-70 respectively.1) For the fixing of lightweight suspended ceiling constructions only.2) For min. axial spacing and min. edge distance the above described loads have to be reduced! (See “Technical Handbook” or design software “CC-Compufix”)


no edge or spacing influences.Recommended loads: material safety factors γM and safety factor for load γL = 1.4 are included. Material safety factor γM depends on type of anchor.

The conditions of application differ from those given in the German approval.

For further detailed information about German approval please contact fischer technical service department.


Suitability

Suitable for:

Concrete ≥ B15 and dense natural stone plus hollow coreslabs

For fixing of:

ideal for fastening with bolts or threaded rods for plumbing,air-conditioning, heating and ventilation installations.Available in zinc plated.

Description

A drop-in anchor with rim so that the anchor always remainsflush with the surface of the substrate. The drill hole cannow be overdepth without effecting the anchor

Technical data

do td lMin.

drill-holedepth for Fixing

Drill � through fixing length QuantityType Art. No. mm mm mm per pack

FDA-R 6x25 62366 8 27 25 100

FDA-R 8x30 62378 10 32 30 100

FDA-R 10x30 62379 12 33 30 100

Mean ultimate loads in kN.

Use 80% of EA loads, see page 47.

48




fischer Drop-in Anchorwith Rim. FDA-R

1

Drop-in anchor with rim1

A rim for the accuratesetting of the anchorflush to the surface, notdependant on hole depth.

fischer Ceiling anchorFDN

1

Ceiling anchor1

Suitability

Suitable for:

Concrete ≥ B15 and dense natural stone

For fixing of:

ideal for fastening suspended ceiling wires or brackets.

Description

A ceiling anchor for rapid installation, with high retainingpower. The wedge shaped segments move over each otherduring insertion, wedging the nail in the hole.

Technical data

do td lMin. .drill-holedepth for Fixing

Drill � through fixing length QuantityType Art. No. mm mm mm per pack

FDN 6/35 78644 6 40 35.0 100

FDN 6/65 78645 6 40 35.0 100

Mean ultimate loads in kN.

An appropriate safety coefficient must be allowed on thesebreaking values (see page 16).

Anchoring base FDN

Concrete ≥ B 25 0.5


fischer Nail Sleeve FNHThe fast and simple fastening made of dacromet-coated sprung steel.

Suitability

Suitable for:

Concrete ≥ B25, solid brick, pressure-resistant natural stone, lightweight building materials.

For fixing of:

Board sub-structures, metal sheets and profiles, small itemsin building interiors

Description

The FNH nail sleeve is a fast and economical fastening madeof dacromet-coated sprung steel. Especially suitable forsmall items in building interiors.When pushed through the object being installed, the sleeveexpands over its entire length in the hole. Simple and time-saving. The object is held by its collar. No screws required.

Nail Sleeve FNH1

1


Technical data

do td hef l tfixMin.drill-hole Effect. Max.depth for anchor- fixingthrough age Fixing thick- Qty.

Drill � fixing depth length ness perType Art. no. mm mm mm mm mm pack

FNH 5/50 50192 5 30 20 50 30 100

FNH 6/30 19863 6 40 30 30 – 100

FNH 6/40 50638 6 50 30 40 10 100

FNH 6/50 77525 6 60 30 50 20 100

FNH 6/60 19864 6 70 30 60 30 100

FNH 6/80 19865 6 90 30 80 50 100

FNH 8/70 19866 8 80 40 70 30 100

FNH 8/90 19867 8 100 40 90 50 50

FNH 8/110 19868 8 120 40 110 70 50

FNH 8/130 19869 8 140 40 130 90 50

FNH 8/150 19870 8 160 40 150 110 50

Installation example

do

l

hef tfixtd

Recommended loads for single anchors of

fischer Nail sleeve FNH in kN

Non-cracked concreteFixing type FNH 5 FNH 6 FNH 8Effective anchorage depth hef [mm] 20 30 40

Drill hole depth h1 � [mm] 30 40 50

Drill hole diameter do [mm] 5 6 8

Tensile ≥ B25 Nrec [kN] 0.20 0.55 1.10

Min. component thickness hmin [mm] 50 60 70

Recommended loads: material safety factors γM and safety factor for load γL = 1.4 are included. Material safety factor γM depends on type of anchor.

49


fischer Nail anchor FNAFor hammerset installation in concrete.

50

Fire resistanceclassificationF 60/90/120

Approved for thetension zone, lightsuspended ceilingsand ceiling covers.

Approvals


Suitability

Suitable for: Concrete ≥ B15.

For fixing of:

Laths, squared timber beams, battens, wood substructures,metal profiles, chains, cables, punched tapes, wire hangers,extension nuts with threaded rods, fire partitions, ventilationpipes, suspended ceilings, C-rails, ceiling insulation on lightwood-wool boards, etc.

Description

The fischer Nail Anchor can be installed swiftly andsmoothly, a real advantage for overhead work.

� Low drilling expenditure, only 6 mm diameter.

� Easy tap-in assembly, two hammer blows are sufficient.

� All building site requirements are available.

� Building inspectorate approval for more safety.

Advantages

FNA with nail head:

For battens and metal hangers. The nail head can be effort-lessly sunk into timber with one blow. On metal parts, itcovers a large surface area, giving a clean finish. Longeruseful lengths bridge non-load-bearing layers.

FNA with M 6 + M 8 thread:

For all demountable connections with metric thread. Connec-tion of threaded hanger rods is possible by means ofextension couplers. Longer threaded portion enables bridgingof non-load bearing layers such as plaster or insulation.

FNA with eye:

For anchoring of hangers, punched tapes, cables or chains.

FNA with hook*:

For suspending chains, lamps, cable loops, rings or otherclosed parts.

FNA for rail fixing:

1

4

5

3

2

Z-21.1-606

Enables quick and easy installation of lightweight railing.

*Not an element of the building inspectorate approval.

FNA with nail headFNA with M6 + M8 threadFNA with eye FNA with hook FNA for rail fixing

Material: zinc plated and passivated steel, A4 stainless steel and highcorrosion resistant steel 1.4529 - see page 52/53.

5

4

3

2

1

Stainlesssteel1.4529

see page 52-53


51

fischer Nail anchor FNA

with nail head � 15 mm

do td hv l da M SWMin. Min. Max.drill-hole anchor- fixing

Steel Steel Drill depth for age Fixing thick- Width Qty.gvz. A4 � through depth length ness across per

Type Art. No. Art. No. mm fixing mm mm mm mm Thread nut pack

FNA 6 x 30/ 5 50938 77802* 6 50 30 45 5 100

FNA 6 x 30/ 30 50940 77805* 6 75 30 71 30 50

FNA 6 x 30/ 50 50942 6 95 30 91 50 50

FNA 6 x 30/ 75 50941 6 115 30 111 75 50

FNA 6 x 30/100 50943 6 150 30 145 100 50

FNA 6 x 30/120 50944 6 170 30 165 120 50

FNA 6 x 40/ 5 50936 6 60 40 55 5 50

* not included in building inspectorate approval

with thread M 6 and M 8

FNA 6 x 30 M 6/5**50920 77806* 6 50 30 52 5 M 6 10 100

FNA 6 x 40 M 8/5**50951 6 55 40 55 5 M 8 13 50

* not included in building inspectorate approval – ** max. installation torque = 4 Nm.

with eye � 10 mm

FNA 6 x 30 OE 50922 6 45 30 64 50

with hook � 10 mm

FNA 6 x 30 H* 50921 6 45 30 64 50


for rail fixing

FNA 6 x 40 S* 50947 6 60 40 55 5 50



Mean ultimate loads and recommended loads for single

anchors of fischer Nail anchor FNA with large axial

spacing and edge distance

Non-cracked concrete Cracked concrete1)

Anchor size FNA FNA FNA FNA6x30 6x40 6x30 6x406x40 M 8/5 6x40 M 8/5

Effective anchorage depth heff [mm] 30 40 30 40Drill hole depth ho � [mm] 45 55 45 55Drill hole diameter do [mm] 6 6 6 6Mean ultimate loads Nu,m [kN]Tensile2) Nu,m [kN] gvz 5.0* 5.0* – –

Nu,m [kN] A4 5.6* – – –Shear2) Vu,m [kN] gvz 3.0 9.8* – –

Vu,m [kN] A4 6.3 – – –Recommended loads Nrec [kN]Tensile2) Nrec [kN] gvz 2.1 2.4 0.5 0.8

Nrec [kN] A4 2,1 – 0.5 –Shear2) Vrec [kN] gvz 1.7 5.1 1.0 1.6

Vrec [kN] A4 2.9 – 1.0 –Component dimensions, minimum axial spacings and edge distancesMin. axial spacing3) smin [mm] 100 120 60 80Min. edge distance3) cmin [mm] 60 80 50 60Min. structural comp. thickness hmin [mm] 100 100 100 100Required torque Tinst [Nm] 4 4 4 4

* steel failure decisive1) For the fixing of lightweight suspended ceiling constructions only.2) Loads are not valid for the anchor type FNA with hook.3) For min. axial spacing and min. edge distance the above described loads have to be reduced!





The condition of application differ from those given in the German

approval.

For detailed design method and design in accordance with German

approval please contact fischer technical service department.

Anchors made of highly corrosion-resistant steelMaterial 1.4529


52

fischer Zykon anchors FZA C fischer Zykon hammerset anchors FZEA C fischer Threaded rods RG M Cfischer Threaded rods FIS G Cfischer Highbond anchor FHB-A Cfischer Nail anchor FNA Cfischer Anchor Bolt FAZ - C 7

6

5

4

3

2

1

1

2

3

4

5

6

Approvals

Suitability

Suitable for:

Concrete ≥ B15.

For fixing of:

Ventilation systems, pipelines, cable trays in road tunnels,installations and suspended ceilings in indoor swimmingpools, steel structures and other mountings in bridge areasas well as in the chemical industry etc.

Description

� In atmospheres with high chloride, sulphur-dioxide andhumidity contents, the risk of corrosion is high due to theconcentration of contaminants.

� For safe and durable fixing, fischer now offers steelanchors which are able to withstand especially corrosiveenvironmental conditions.

� These new fastening elements are made of high-alloysteel with material number 1.4529.

� In material approval Z-30.3-6, this highly corrosion-resistantsteel has the highest resistance classification of IV.

from version 5.0

Advantages

� Fast and safe anchoring is now possible in areas whichwere not previously included in the approval. The variousareas of application are regulated in the approval therebyallowing maximum planning safety even in critical cases.

� With the FZA Zykon Anchor, the FZEA Zykon HammersetAnchor, the FHB Highbond Anchor and the FNA NailAnchor, fischer now offers fixing elements of material1.4529 which are suitable for use in the tension zone.

� The right anchor for every fixing task. Whether as bolt,push-through, interior-thread or synthetic-resin anchor,fischer has the right fixing for your purpose.

� In long years of research, fischer has accumulated anunequalled expertise in this field which we are happy topass on to our customers. Just contact our fieldengineers.

� We manufacture job-specific products to yourrequirements. This guarantees you maximum flexibility,even with special dimensions.


Z-21.1-958 Z-21.3-1615

Z-21.3-1707

FZA FZEA R + ETA option 8

FHB

FAZ

FNA

7

Anchors made of highly corrosion-resistant steelHIGH PERFORMANCE STEEL ANCHORS

53

Technical data

Zykon anchor FZA C

Material 1.4529See page 21 “Tools”.

Effect. Max.anchorage fixing Width Qty.

Drill � depth thickness across perType Art. No. mm mm mm Thread nut pack

FZA 10 x 40 M 6/10 C* 96214 10 40 10 M 6 10 25

FZA 10 x 40 M 6/35 C 96361 10 40 35 M 6 10 25

FZA 12 x 40 M 8/15 C 96215 12 40 15 M 8 13 25

FZA 14 x 40 M 10/25 C 96228 14 40 25 M 10 17 25

FZA 12 x 50 M 8/15 C* 96227 12 50 15 M 8 13 20

FZA 12 x 50 M 8/50 C 96362 12 50 50 M 8 13 20

FZA 14 x 60 M 10/25 C* 96216 14 60 25 M 10 17 10

FZA 14 x 60 M 10/50 C 96358 14 60 50 M 10 17 10

FZA 18 x 80 M 12/25 C* 96315 18 80 25 M 12 19 10

FZA 18 x 80 M 12/55 C 96359 18 80 55 M 12 19 10

FZA 22 x 100 M 16/60 C 96364 22 100 60 M 16 24 10

FZA 22 x 125 M 16/60 C 96360 22 125 60 M 16 24 6

FZA 12 x 50 M 8 D/10 C 96319 12 40 10 M 8 13 25

FZA 12 x 60 M 8 D/10 C 96353 12 50 10 M 8 13 25

FZA 12 x 80 M 8 D/30 C 96354 12 50 30 M 8 13 25

FZA 14 x 80 M 10 D/20 C 96355 14 60 20 M 10 17 10

FZA 18 x 100 M 12 D/20 C 96356 18 80 20 M 12 19 10

FZA 18 x 130 M 12 D/50 C 96357 18 80 50 M 12 19 10

* Article available from stock.Prices, delivery times and other dimensions available on request.


Resin anchor threaded rod RG M C

Hammerset anchor FZEA C

Material 1.4529 See page 25, Tools

Anchorage Screw-in Qty.Drill � depth Internal depth mm per

Type Art. No. mm mm thread min. max. pack

FZEA 10 x 40 M 8 C* 96236 10 40 M 8 11 17 100

FZEA 12 x 40 M 10 C* 96237 12 40 M 10 13 19 100

FZEA 14 x 40 M 12 C* 96238 14 40 M 12 15 21 50


Material 1.4529 Available with glass capsule RM or injection resin FIS V, both with ETA

approval - see page 13

Min. Min. Max. SWdrill- anchor- fixing (Widthhole age thick- across) Qty.

Drill � depth depth ness Fits resin hexagon perType Art. No. mm mm mm mm capsule nut pack

RG M 8 x 110 C* 96316 10 80 80 13 50270 13 10

RG M 10 x 130 C* 96217 12 90 90 20 50271 17 10

RG M 12 x 160 C* 96218 14 110 110 25 50272 19 10

RG M 16 x 190 C* 96219 18 125 125 35 50273 24 10



Information on this product range and sizes was not available at time of printing. For furtherdetails please contact fischer customer services 01491 827900

Installation examples

Technical data

Highly corrosion-resistant stainless steel (material: 1.4529)

do ho hef da M SWEffect.an-

Drill- chor- Fixinghole age thick- Hexa- Qty.

Drill � depth depth ness gon Required perType Art. No. mm mm mm mm Thread nut resin set

FHB-A 10 x 60/10 C 62401 12 65 60 10 10 17 * 10

FHB-A 10 x 60/60 C 62402 12 65 60 60 10 17 * 10

FHB-A 12 x 80/10 C 62403 14 85 80 10 12 19 * 10

FHB-A 12 x 80/60 C 62404 14 85 80 60 12 19 * 10

FHB-A 12 x 100/25 C 62405 14 105 100 25 12 19 * 10

FHB-A 12 x 100/60 C 62406 14 105 100 60 12 19 * 10

FHB-A 16 x 125/30 C 62408 18 130 125 30 16 24 * 10

FHB-A 16 x 125/60 C 62407 18 130 125 60 16 24 * 10

FHB-A 20 x 170/50 C 62409 24 175 170 50 20 30 * 10

FHB-A 24 x 220/50 C 62418 28 225 220 50 24 36 * 5

* For the correct resins FIS HB 345 S and FIS HB 150 C, see page 2.Prices, delivery times and other dimensions available on request.

do td hv l da M SWMin. drill- Min. Max.hole depth anchor- fixingfor through age Fixing thick- Width Qty.

Drill � fixing depth length ness across per.Type Art. No. mm mm mm mm mm Thread nut pack

FNA 6 x 30/5 C* 77807 6 50 30 45 5 – – 100

FNA 6 x 30/30 C* 77808 6 75 30 71 30 – – 50

FNA 6 x 30 M 6/5 C* 77809 6 50 30 52 5 M 6 10 100

* Approval pending

With nail head � 15 mm with thread M 6 and M 8

Highbond anchor FHB-A C

Nail anchor FNA

fischer Anchor bolt FAZ

For your notes


54

Documents

Fischer Fbn Anchors