Fixing Technology - Bradfastbradfast.com.au/wordpress/.../uploads/Ramset_Fixing... · Fixing to steel The resilience of steel provides a clamping effect to the fixing. This combined

Fixing TechnologyProduct Catalogue

www.ramset.com.au 1300 780 063 1

Gas TechnologySystems Pa

ge 3

Powder ActuatedSystems Pa

ge 3

5

2 www.ramset.com.au 1300 780 063

Gas TechnologySystems

Ramset™ Gas Technology tools employ the latest

technology to fasten to concrete, steel, and other

common building materials. These revolutionary gas

technology systems are extremely fast, cost

effective and include automatic power adjustment

for greater ease of use.

Ramset™ Gas Technology tools are used by many

professional contractors in Australia and around the

world including ceiling and partitioning contractors,

insulation installers, electrical contractors,

plumbing contractors, pest control installers and

formwork contractors.

Tools in this range include:

• CableMaster™

• TrakMaster™

• TrakFast™

• InsulFast™GT.



Gas TechnologySystems


ContentsGas Technology Systems

CableMaster™ 8

Fastening Principles 6

TrakMaster™ 22

TrakFast™ 26

InsulFast™ GT 30

CableMaster™ Consumables 10• Consumable Selection Guide• ClipElec™

• CTClip™

• EClip• Threaded Rod Hanger• FP FireFix™ Clips• CableHorn™

• Combination Clip• Half Saddles & Adaptors• Strap & Plate Washer• Catenary Wire Bracket

TrakMaster™ Consumables 24

TrakFast™ Consumables 28

InsulFast™ GT Consumables 32


Fastening PrinciplesGas Technology Systems

Fast

enin

g Pr

inci

ples

Gas Technology - How it works

With its own internal combustion engine, Ramset™ Gas Technology fastens cable management, wiring accessories and partitioning track much faster than any other system!

At the heart of Ramset™ Gas Technology is the patented linear internal combustion engine. With its steel piston rings and precision-machined combustion chamber, Ramset™ Gas Technology drives fasteners all day long, week after week, year after year.

1. Spark Plug

2. Fan Motor

3. Fuel Port

4. Combustion Chamber

5. Piston Assembly

6. Cylinder

31

4

5

2

6

How to select a Ramset™ Drive Pin to directly fasten an object to STEEL

Fixing to concreteAs the fixing enters the concrete, extreme pressure and heat are created. This creates a bond that provides high loading strength in concrete.

Edge distanceDo not fix closer than 75mm from the edge of concrete. If the concrete cracks, the fixing may not hold.

Recommended minimum fixing spacingSetting fixings too close together can cause the concrete to crack. The recommended minimum distance between fixings is 50mm. Never attempt a fixing application too close to another fixing as this could affect the previously inserted fixing’s embedment.

Concrete thicknessIt is important that the concrete be at least three times as thick as the fixing penetration. If the concrete is too thin, the compressive forces forming at the fixing’s point can cause the free face of the concrete to break away. This creates a dangerous condition from flying concrete and / or the fixing and also results in a reduction of fastener holding power.

How to select a Ramset™ Drive Pin to directly fasten an object to CONCRETE

Fixing to steelThe resilience of steel provides a clamping effect to the fixing. This combined with the tremendous heat that is created, provides a welding and clamping effect to give maximum holding power.

Edge distanceThe recommended edge distance for a fixing to the edge of steel is 13mm. Never fire the tool within 13mm of the edge of a steel base material because the steel may bend or break off, allowing the fixing to ricochet.

Recommended minimum fastener spacingThe recommended minimum distance between fixings is 25mm. Never attempt a fixing application too close to another fixing as this could affect the previously installed fixing’s embedment.

Steel thicknessDo not fasten into steel base material thinner than the fastener shank diameter. Holding power may be reduced and the fastener may be overdriven.

As a guide when:Fixing into steel - min. steel thickness = 3mm(Less with specialist pins contact Ramset™ for further details)

Minimum Shank Length

Thickness + 15mmof material

(M)

M


Thickness + Steel + 5mm of material Thickness point

(M) (T) allowance

M

T


Fastening PrinciplesGas Technology Systems

Fastening Principles

Adjusting PenetrationPenetration is adjusted by slackening the two screws (A) on the upper part of the barrel using the allen key provided and moving them backwards or forwards (4mm) in the recess on plate (B).

The adjustment range is 4mm. Intermediate adjustments between maximum and minimum are possible.

For best fixing results, check the adjustment position before and during work.

Pulsa™ Technology - TrakMaster™, InsulFast GT™ & CableMaster™ Only

As gases are affected by temperature, to generate exactly the same power in a gas technology tool the fuel injector must vary the amount of gas delivered to the combustion chamber. With traditional mechanical fuel delivery systems as found in the TrakFast™ tool this variation is not possible and differences in power are evident at very low (i.e. -5°C) or high temperatures.

However, the TrakMaster™, InsulFast™ GT and CableMaster™ tools use PULSA™ technology which employs temperature dependent Electronic Fuel Injection (E.F.I.) to accurately inject the exact amount of gas that the tool requires, no matter what the ambient temperature is. The tool actually detects what the ambient temperature is and calculates the amount of gas to release from the fuel cell. This ‘smart’ technology ensures that the tool delivers the right amount of power…. every time!

Adjusting Fastener Penetration – Recommended for use with TrakMaster™ Only

All Ramset™ Gas Technology tools automatically adjust their power to suit the supporting material. These gas technology tools can adjust their power up to a maximum impact energy that is determined by the capability of each tool model. (This is one of the main differences between Ramset™ Gas Technology tools and Powder Actuated tools).

Even though Ramset™ Gas Technology tools automatically adjust their power, certain applications may require the fastener to penetrate deeper into the base material or penetrate less.

Ramset™ TrakMaster™ and CableMaster™ tools are designed with a feature that allows adjustment of the fastener penetration to be performed. This adjustment is dependent both on the type and hardness of the base material and on the object being fixed. The adjustment does not affect the impact energy that is supplied to the fastener.

To ensure successful fixing of CableMaster™ clips (EClip™ etc.) it is recommended that the CableMaster™ tool is set to the minimum drive position. Failure to do so could result in cracking or breaking of accessories and PVC trunking. The CableMaster™ is supplied adjusted to this position and it is recommended that the tool be left in the minimum drive position and different pins be selcted to achieve different embedments.

Maximum Penetration

Minimum Penetration

A B


CableMaster™

For Electrical & Plumbing Contractors

Features & Benefits•Cordless-selfpowered,nosettinguptimerequired•Sequentialactuation-safeoperation•Powerfulmotor(82J)•Muchfasterthanthetraditionaldrillandanchormethod•Lock-outfeature(safety)•Fastenerguidedesignedformechanicalandelectricalcontractwork•5kgactuationforce•Softcushionedgrip•Voltageindicatorlight•Wellbalanced•Compactcarryingcase•In-carchargeradaptor(accessory)•Heatsensorcontrolsamountofgasinjected,relativetotheambient

temperature•Electronicallycontrolledfuelinjection•Lowmaintenance.DesignedtoworkinallAustralianconditions

Gas

Tech

nolo

gy S

yste

ms

DescriptionRamset™CableMaster™isthefastestmethodofmechanicalandelectricalinstallation.Usingpatentedgastechnology,designedwithanumberofnewfeaturesallowingquicker,saferinstallationwithgreaterusercomfortandthelowesttotalinstalledcost.

Related ProductsDrive Pins & Fuel CellsContractor Packs

SpecificationsWeight 3.7kgHeight 383mmLength 295mm

Magazine Capacity20(+3)pinmagazine,[40(+3)pinmagazineaccessory]

Impact Force 82JActuation Pressure 5kgOverdrive 4mmIntermittent Operation 2pinspersecondFuel Cell Life 650pins(approx)Battery Charge Capacity 1,000pins(approx)Battery Voltage 6VBattery Amperage 600mABattery Charge time 1hourPower Regulation AutomaticOperating Temperature Range -5°C to 49°CSubstratesConcrete,CompositeSteelDecking,SolidBrick,PrecastConcrete,SteelPre-stressedConcrete,HollowBlockWall,ReinforcedConcrete,ReinforcedPrefabricatedConcrete

ElectronicFuel Injection

Removable20 Pin Magazine

(40 Pin Magazine Available)

Compact & Lightweight Design


CableMaster™

For Electrical & Plumbing Contractors

AccessoriesPart No Description Order Qty336800 CableMaster™FastenerGuide 1010670 40PinMagazine 1PULSALIFT PoleTool(2.4mto3.8mworkingheight) 1PA1613 SafetyGlasses 1TMBP Battery 1900507 In-carCharger 1TMBC ReplacementCharger 1TMBCPS AC/DCAdaptor 1B20544L GasToolDegreaserandLubricant 1CS42025 SaddleAdaptor20/25mm 1

Gas Technology Systems

Standard Operating ProcedureAlwaysreadandunderstandtheinstructionmanualbeforeattemptingtooperateaRamset™GasTechnologyTool.1. Firstinsertthefuelcellandbatteryintothetool.2. Insertthecollatedfastenersintothemagazine.3. Theclipshouldthenbeplacedontheendofthefastenerguidewithoutcompressingthefrontendofthetool.4. Thetoolshouldthenbecompressedagainsttheworksurface.(Makingsurethatthetoolisperpendiculartotheworksurface).5. Oncethetooliscompressedthetriggercanbeactuatedandthefastenerisdrivenintothesubstratesecuringtheclipinplace.

CableMaster™

Part No Description Order QtyCABLEMASTER CableMaster™Pulsa™Tool+2xBatteries 1

Kitincludes:CableMaster™Pulsa™tool,highimpactcarrycase,2xbatteries,batterycharger,safetyglasses,allenkey,dustcover,saddleadaptorandinstructionmanual

Trades & Applications Plumbing Electrical Fire & Contractor Contractor SecurityPermanent cable suspension to concrete and steel 4

Pipe suspension systems to concrete and steel 4

Fire and security cabling to concrete and steel 4

Temporary cable suspension to concrete and steel 4


CableMaster™

Consumables

Part No Description Length Order QtyHC615 HeavyDutySteel/Concrete 15mm 500SC620 HeavyDutySteel/Concrete 20mm 500HC617 PremiumHardConcrete/Steel 17mm 500HC622 PremiumHardConcrete/Steel 22mm 50010stripcollation(suitableforusein20and40pinmagazines)+1xFuelCell

Part No Description Length Order QtyCG620 SoftWasheredPin 20mm 500CG625 SoftWasheredPin 25mm 500CG630 SoftWasheredPin 30mm 500CG635 SoftWasheredPin 35mm 500

10stripcollation+1xFuelCell

Soft Washered Pin Range for Steel and Hard Concrete FixingThe Soft Washered pin range is designed for use with pre-drilled PVC fittings where the pre-drilled hole size is between 3.0 to 8.0mm in diameter. These pins are used to securely fasten a variety of PVC fittings to concrete. They are used in a single shot format and are not suitable for use with a magazine.

Heavy Duty Pin Range for Steel and Hard Concrete FixingDrive Pins designed for fastening to standard strength concrete, masonry and steel.

SpecificationsRaw Material CarbonSteelCorrosion Protection Zinc Electroplated (Minimum coating 5µm)Nominal Head Diameter 6.3mmNominal Shank Diameter 2.6mm(C620Steppedshank2.6/2.2mm)Shear Strength 1120N/mm2

Tensile Strength 1800N/mm2

Hardness 52-56HRC

SpecificationsRaw Material CarbonSteelCorrosion Protection Zinc Electroplated (Minimum coating 5µm)Nominal Head Diameter 6.3mmNominal Shank Diameter 2.6mmShear Strength 1120N/mm2


Hardness 52-56HRC

Nominal Washer Diameter 11.0mm

Gas

Tech

nolo

gy S

yste

ms

Ramset™ recommends application test on-site before commencing use.

Application Type


CableMaster™

Consumable Selection Guide

4 Recommended


CableMaster™ Consumables

ClipElec™ 4 4 4 4 4 4

CTClip™ 4 4 4 4 4 4

EClip™ 4 4 4 4

Threaded Rod Hanger 4 4 4 4

FP FireFix™ Clip 4 4

CableHorn™ Double & Single 4

Combination Clip 4 4 4 4 4

Direct Alignment Half Saddle 4 4 4

Half Saddles & Adaptors 4 4 4

Strap & Plate Mounting Washer 4

Catenary Wire Bracket 4 4

Strap, Plates & Fixtures

Light Duty Cable Tray

Flexible/Plastic Pipe

Catenary W

ire

Electrical Conduit

Cable Fixing

Small Diam

eter Rigid Pipes

M

etal Pipes

M

etal/Nylon Straps

Fire &

Service Cabling



Gas

Tech

nolo

gy S

yste

ms

ClipElec™


ClipElec™ All-purpose Cable Tie ClipsPart No Description Order QtyCLIPELEC ClipElec™All-purposewithCableTie 100

CPGCLClipElec™ContractorPack(500xclips,SC620Pins,FuelCell,CableTies200mmx4.8mmBlack)

1

CPGCLHC617ClipElec™HardConcreteContractorPack(500xclips,HC617Pins,FuelCell,CableTies200mmx4.8mmBlack)

1

CPGCLHC622ClipElec™HardConcreteContractorPack(500xclips,HC622Pins,FuelCell,CableTies200mmx4.8mmBlack)

1

Features & Benefits•ClipElec™canbeusedforcable,conduitandtubework.•Universaldesignallowscabletiesupto9mmwide.•Designedwithanin-builtenergyabsorberforperfectembedment.•ClipsdirectlyontotheCableMaster™PinGuideforonehandedoperation.•HandsareasafedistancefromthePinGuideduringinstallation.•CanbeusedwiththePulsaLift™Poletofixfromtheground.•Optionalplugandscrewinstallation.

Specifications

Raw MaterialPolypropylenecopolymer,highimpact,halogenfree.UVresistant

Capacity Upto9mmcabletiewidth.Spacing Recommendation 0.5&1metre(approx)

Fire Resistance Properties

Incandescentwiretest(regulationNFC20-455)750°Cpassed-LCIElaboratorytestresultsN°438309(December1998)

Low Temperature Test Nobreakageat0°CDimensions 32x37mm

*NOTE:Testconcludedwhenclippulledoverpinheadorcabletiefailed.Job-sitetestingmayberequiredtodetermineactualachievablejob-sitevalues.ResultshavebeenachievedwithaCableMaster™toolsetatminimumoverdrivesetting.Accessoriesfailingtofixcorrectlyshouldberemovedandanewfixingsetawayfromanyspalledconcrete.Tensionloadsprovidedareforstaticloadsituationsonly.Valuesrepresentaminimumfactorofsafetyof3:1onthelowesttestresultsachieved.Minimumedgedistance75mm,minimumspacingbetweenfixings50mm.Tensionloadsareperfixing,howeveraminimumof3fixingsperfasteningunitshouldbeused.

DescriptionClipElec™isanallpurposecabletiesystemthatmaybeusedforfixingcable,conduitandpipesforawidevarietyofelectricalandplumbingapplications.Thissystemisextremelyversatileallowingformanydifferentsizedcables,pipesandconduittobesecured.TheClipElec™allpurposecabletiesystemmaybeusedwiththe4.8mmsuppliedcabletiesorwithothercabletiesuptoamaximumwidthof9mm.

Installation Procedure1.SimplycliptheClipElectothetoolpinguide.2.Pressagainstthesubstrate,pressthetrigger&theclipisfixed.3.Installthetubeorconduitwithcabletie.

Pin Selection Guide Substrate HC617 HC622 SC620Hard Concrete >50MPa 4 4 k

Concrete <50MPa 4 4 4

Hollow Concrete Block k 4 4

Steel 4 4 4

Steel Decking 4 4 4

4 Suitable k Possible

Performance Table*

PinLoad Capacity (Tension) - Concrete

Cable Tie Width 20MPa 32MPaSC620 9mm 10kg 12kgHC617 9mm 10kg 12kgHC622 9mm 10kg 12kgC620 4.8mm 2.5kg 3.7kg



CTClip™

Part No Description Pipe / Conduit Diameter Order QtyCTCLIP GreyAssembledCableTieClip 16-32mm 100CPGCT CTClip™ContractorPackStandard(500xclips,SC620Pins,FuelCell) 16-32mm 1CPGCTL CTClip™ContractorPackLarge(300xclips,SC620Pins,FuelCell) 40-63mm 1

Performance Table*Load Capacity (Tension) - Concrete

Pin 20MPa 32MPaSC620 4kg 10kgHC617 7kg 9kgHC622 7kg 10kg

SpecificationsRaw Material High impact, Nylon 66Spacing Recommendation 0.5 & 1 metre (approx)Fire Resistance Properties UL94HB Fire Test

DescriptionTheCTClip™istheallinonecabletiesystem.WiththeintegralcabletietheCTClip™canbeusedforcable,conduitandtubework.Nowavailablein2sizestheCTClip™systemallowsformaximumcableclustersortubediametersupto63mm.

Installation Procedure1.Sidemountclipintopinguide.2.Pressagainstworksurface.Firetool.3.Installthecableorconduit/tubeasrequired.Fastentiestrap.

Pin Selection GuideSubstrate HC617 HC622 SC620Hard Concrete >50MPa 4 4 k



Steel 4 4 4

Steel Decking 4 4 4


CTClip™


*NOTE: Test concluded when clip pulled over pin head or cable tie failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster™ tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 on the lowest test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used.


Features & Benefits• CTClip can be used for cable, conduit and tube work.• Maximum cable cluster or tube diameter of 63mm.• Clip base raised above work surface.• In-built energy absorber for optimum pin penetration.• Side mount clip into pin guide.• One handed installation.• Fix from the ground with the PulsaLift™ Pole.• Optional plug and screw installation.



Gas

Tech

nolo

gy S

yste

ms

EClip™ CableMaster™ Consumables

Performance TableTube extraction loads at 22°CForce required to manually remove tube from the clip

Clip Size Average Ultimate Load (approx)16mm 4kg20mm 6kg25mm 8kg32mm 8kg

Pin Selection GuideSubstrate HC617 HC622 SC620Hard Concrete >50MPa 4 4 k



Steel 4 4 4

Steel Decking 4 4 4


DescriptionTheEClip™isidealforfirmlysecuringconduit,HDPE,andPVCpipe.Onceinstalled,theclipisabletoberotatedtoallowforprecisepositioningofrigidandflexibletube.ThedesignoftheEClip™incorporatesinterlockingconnectionstoallowformultipleclipstobejoinedtogethersidebysideforaprofessionalfinish.

SpecificationsRaw Material

High quality polypropyleneHalogen free. Fire resistant

Spacing Recommendation 0.5 and 1 metre (approx)

EClip™ Conduit ClipPart No Description Pipe / Conduit Diameter Order QtyECLIP20 GreyConduitClip 20mm 500ECLIP25 GreyConduitClip 25mm 500CPGEC16 ContractorPack(500xclips,SC620Pins,FuelCell) 16mm 1CPGEC20 ContractorPack(500xclips,SC620Pins,FuelCell) 20mm 1CPGEC25 ContractorPack(500xclips,SC620Pins,FuelCell) 25mm 1CPGEC32 ContractorPack(250xclips,SC620Pins,FuelCell) 32mm 1

Installation Procedure1. Side mount the EClip™ onto the tool Pin Guide.

2. Fixing is quick and precise.

3. When fixed, it can be easily rotated around the pin to adjust its position.


Features & Benefits• The EClip™ is designed to clip easily onto the CableMaster™ Pin Guide from the side allowing one-handed operation.• Hands are a safe distance from the Pin Guide during installation.• Fixing is precise.• After installation the EClip™ can be rotated around the pin to adjust alignment.• The slotted design of EClip™ absorbs energy, preventing the pin head from splitting the clip.• The hollow structure of the EClip™ gives flexibility for easy insertion of conduit.• EClip™ incorporates male/female connections allowing multiple conduit installation side by side.• Optional plug and screw installation.


Threaded Rod HangerPart No Description Thread Diameter Order QtyTRH0810 ThreadedRodHanger M8-M10 100CPGTRH ThreadedRodHangerContractorPack(400xhangers,HC617Pins,FuelCell) M8-M10 1

Gas Technology SystemsThreaded Rod Hanger


SpecificationsRaw Material Carbon SteelMaterial Thickness 1.5mmCoating Zinc Electroplated (Min. Coating 7µm)

Installation Procedure1.InsertTRHlaterallyontoCableMaster™pinguidetothestop

position.2.InstalltheTRH.Thepinguidewillautomaticallyremoveitself

fromthechannel. Iftheguideisstuckinsidethechannel,gentlymovethetool

laterallytoreleaseit.3.Screwinthethreadedrod,(twopossiblediameters)and

bendtheTRHtotheverticalpositionusingtherodorBendtheTRHbyhandifyouintendtouseasuspendedhangingsystem,smallchainorsteelwire.

Pin Selection GuideSubstrate SC620 HC617 HC622Hard Concrete >50MPa k 4 k

Concrete <50MPa k 4 k

Hollow Concrete Block 4 4 4

Steel 4 4 k

Steel Decking 4 4 4



32MPaTRH with HC617 Pulsa™ Pin 15kg

*NOTES:

1. Values represent the maximum recommended working load in tension.

2. A minimum of 4 fastenings per fastened unit must be used.

3. Results have been achieved with a CableMaster™ tool.

4. All visible failures must be replaced and a new fixing set away from any spalled concrete.

5. Tension loads provided are for static load situations only.

6. Job-site testing may be required to determine actual achievable job-site values.

7. Pins must be sufficiently set, such that the underside of the head of the pin is in contact with the surface.

TyMaster™ powder actuated tool installationsForheavydutyapplicationsrefertoZBracketrodHanger(M10)Page52.ThisisarodhangerassemblyforTyMaster™powderactuatedtoolinstallations.

DescriptionForlightdutyapplicationstheThreadedRodHangerbracketisanidealalternativetotraditionalanchorssuchastheDynaSet™drop-inanchor.ThebracketfeaturesanM8andaM10threadallowingforachoiceofthreadedrodsizesinapplicationssuchaslightdutycabletrayandpipesuspension.Thebendingmovementusedduringapplicationactsasaselftestingmechanismforthequalityofthefixing.


Features & Benefits• Slide-on channel for pin guide. Lateral insertion for fast, safe installation.• Thick steel with reinforcing ribs for extra strength.• Dual threads. Less parts, more flexibility.• Optional drill and 6mm anchor installation.• Electro zinc coating protects against corrosion.


Gas

Tech

nolo

gy S

yste

ms

FP FireFix™ ClipsCableMaster™ Consumables

FireFix™

Part No Description Cable Outer Diameter

Order Qty

CPGFPO2 FireFix™ClipContractorPack(500xclips,SC620Pins,5FastenerGuideAdaptors) 7-8.1mm 1CPGFPO4 FireFix™ClipContractorPack(500xclips,SC620Pins,5FastenerGuideAdaptors) 8-9.5mm 1

DescriptionThe FP FireFix™ clip fire cable installation system has been developed for installing the specialised fire protection cable required for the safe operation of essentail service equipment during fire emergencies. This system consists of the FP FireFix™ clip installed with a Pulsa™ pin using the CableMaster™ Pulsa™ gas tool.

Features & Benefits• Complies to AS1530.4• Fixes fire rated cables ten times faster than traditional drilling methods• Clip manufactured from 316 Stainless Steel powder coated• Simply clips shut holding the cable(s) securely. 2 cables per clip• Can be used with stainless steel cable ties to install larger cables• Fast fixing to non combustible materials such as solid concrete, hollow

concrete block and steel Two hour fire protection system for essential services.

• Utilises a plastic adaptor that fits on the CableMaster™ Pin Guide allowing one-handed installation.

• Hands are a safe distance from the Pin Guide during installation.• Can be used with the PulsaLift™ Pole to fix from the ground.• Holds one or two cables. Choice of two sizes.• Simply clips shut holding the cable(s) securely. 2 cables per clip.

Installation Procedure1. Fit adaptor to the CableMaster™ pin guide.

2. Position the FP FireFix™ clip

3. Push the tool against the substrate and fix the

FP FireFix™ clip in place.NOTE: remove battery from the tool when fitting the FP FireFix™ adaptor.

Pin Selection GuideSubstrate SC620 HC617 HC622 Hard Concrete >50MPa k 4 4



Steel 4 4 4

Steel Decking 4 4 4


SpecificationsRaw Material Stainless SteelCoating Powder coated red




CableHorn™ FixingPart No Description Fixing Capacity Order Qty CABLEHORN DoubleCableHorn™ 16Cables(3x1.5mm2) 35CPGCH140 CableHorn™ContractorPack(200xfixings,SC620Pins,FuelCell) 8Cables(3x1.5mm2) 1CPGCH CableHorn™ContractorPack(125xfixings,SC620Pins,FuelCell) 16Cables(3x1.5mm2) 1

CableHorn™


Features & Benefits• Designed for use with electrical, data and communication cables.• Replaces the need for cable tray and catinary wire.• Clips directly onto the CableMaster™ Pin Guide allowing one-handed

operation.• Can be used with the PulsaLift™ Pole to fix from the ground.• Add or remove cables as required.• In-built energy absorber for perfect embedment.• Large fixing base for better stability.• Flexibility in installation-vertical, horizontal, overhead.• Optional plug and screw installation.

Pin Selection GuideSubstrate HC622 SC620 Hard Concrete >50MPa 4 k

Concrete <50MPa 4 4

Hollow Concrete Block 4 4

Steel 4 4

Steel Decking 4 4


Installation Procedure1. Simply clip the CableHorn™ to the tool pin

2. Press against the substrate (5kg to actuate the tool) press the trigger to fix.

3. Install the cable simply by lifting the edge of the CableHorn™.

*NOTE: Test concluded when clip pulled over pin head or pin failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster™ tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 on the lowest test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used.

DescriptionInmanyapplicationstheuseoftheCableHorn™systemcaneliminatetheneedforcabletraystobeinstalled.CablesmaybeaddedorremovedaftertheCableHorn™isinstalled.WhenusedinconjunctionwiththePulsaLift™polesystem,CableHorns™maybeinstalledfromthegroundwithouttheneedforladdersorscissorlifts.

Specifications

Capacity

Single CableHorn™: 8 cables, 3 x 1.5mm2 maximum.Double CableHorn™; 16 cables, 3 x 1.5mm2 maximum

Spacing Recommendations Between 0.60m and 1.50m

Raw MaterialHigh impact modified Pa66 Halogen free polypropylene.

Fire Resistance PropertiesIncandescent wire test (IEC 695): 650 °C UL94 HB (ISO 1210): 100 mm/min

Low Temperature Tests No breakage at 0 °CQuality Certificate TUV certificate ISO 9001

DimensionsSingle CableHorn™: Length 137mm. Double CableHorn™: Length 228mm

Fixing BaseSingle CableHorn™: 19.5 x 38.5mm. Double CableHorn™: 19.5 x 24.3mm


Pin 20MPa 32MPaHC622 18kg 20kgSC620 18kg 20kg



Gas

Tech

nolo

gy S

yste

ms

Combination ClipCableMaster™ Consumables

Combination Clip with StrapPart No Description Pipe / Conduit Diameter Order Qty363015 OnePieceClipwithReleasableClip 15-16mm 100363020 OnePieceClipwithReleasableClip 20-25mm 100363028 OnePieceClipwithReleasableClip 28-32mm 50363035 OnePieceClipwithReleasableClip 35-42mm 50363050 OnePieceClipwithReleasableClip 50mm 50

Features & Benefits• Less parts, faster installations, lower installed costs.• Channel or individual mount.• Suitable for use with large cables and conduits.• Choice of fixing method: - Pulsa™ gas fix with CableMaster™.

- “Slide-on” channel mount.

- Drill and anchor.

- M6 threaded base for rod/screw attachment.

• Male/female connection. side by side mounting.• Wide (15mm) strap. Open with screwdriver.• Patent pending.

SpecificationsRaw Material

Copolymer. UV resistant.

Halogen free.

Spacing Recommendation0.5 & 1 metre (approx) for Pulsa™ gas fix.

Temperature Resistance Properties

Maximum recommended temperature 102°C.

Installation Procedure1. Side mount clip into pin guide.

2. Press against work surface. Fire tool.

3. Install the cable or conduit/tube as required. Fasten tie strap.

Performance Table*Load Capacity (Tension) - 35MPa Concrete

Pin Combination Clip 32mmSC620 15kgHC622 15kg

*NOTE: Test concluded when clip pulled over pin head or strap failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster™ tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 based on the test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used.

Pin Selection GuideSubstrate HC622 SC620Hard Concrete >50MPa 4 k

Concrete <50MPa 4 4

Hollow Concrete Block 4 4

Steel 4 4

Steel Decking 4 4


DescriptionTheCombinationClipisafullyenclosedclipsystemsuitableforsecuringconduitandtube.TheCombinationClipcanbeopenedwithascrewdriverifrequired.Thisallowsforconduitandtubetoberemovedandreplacedwithouttheneedforanewclip.



Direct Alignment Conduit Half SaddlesPart No Description Pipe / Conduit Diameter Order QtyCPGDAS20 DirectAlignmentSaddleContractorPack(400xsaddles,SC620Pins,FuelCell) 20mm 1CPGDAS25 DirectAlignmentSaddleContractorPack(400xsaddles,SC620Pins,FuelCell) 25mm 1


Conduit Half SaddleCableMaster™ Consumables

DescriptionConduitHalfSaddlesaresuitableforfixingconduitandmetalpipes.StandardHalfSaddlesmaybeusedwiththeCableMaster™toolinconjunctionwithaSaddleAdaptor.DirectAlignmentSaddlesmakethejobevenfasterbyclippingdirectlyontothefastenerguide.

Pin Selection GuideSubstrate SC620 HC617 HC622Hard Concrete >50MPa k 4 4



Steel 4 4 4

Bondeck 4 4 4


Installation Procedure1. Gently place saddle assembly into end of pin guide.

2. Place saddle over conduit/tube.

3. Depress nose piece against work surface, fire tool.

Features & Benefits• FAST accurate fixing of conduits and tubes to concrete,hollow block, & steel.• Fits directly to nose piece of CableMaster™ Pulsa™ gas tool• Precise hole alignment.• Optimum pin penetration and strength.• Neat and flush finish.• One hand installation.• Optional drill and 5mm anchor installation.• Site test recommended for use in critical applications.

Half Saddles and Saddle AdaptorsPart No Description Pipe / Conduit Diameter Order QtyCSH20 HalfSaddle 20mm 100CSH25 HalfSaddle 25mm 100CPGSH20 HalfSaddleContractorPack(400xsaddles,SC620Pins,FuelCell) 20mm 1CPGSH25 HalfSaddleContractorPack(400xsaddles,SC620Pins,FuelCell) 25mm 1CSA2025 SaddleAdaptor 20/25mm 1CSA1632 SaddleAdaptor 16/32mm 1

SpecificationsRaw Material Carbon SteelMaterial Thickness 1.6mmCoating Zinc Electroplated (Min. Coating 7µm)


Half Saddle Saddle Adaptor

Direct Alignment Conduit Half Saddles


Gas

Tech

nolo

gy S

yste

ms

Strap/Plate WasherCableMaster™ Consumables

Strap and Plate WasherPart No Description Order QtySPMW StrapandPlateWasher 500

SpecificationsSteel type CA2S-E.

Steel Thickness1.6mm providing a high resistance to deformation.

Nominal Diameter 16mm

Installation Procedure1. Gently place washer assembly into end of nose piece.

2. Place assembly tip in position.

3. Depress nose piece against work surface, fire tool.

DescriptionTheStrapandPlateWashermaybeusedinawidevarietyofapplicationswherethinmaterialsorfixtureswithexistingholesneedtobequicklyfastened.CommonapplicationswheretheStrapandPlatewasherareusedincludesecuringthinmetal,nylonandVelcrostrapsforducting,cablebunchesandotherfixtures.Bracketswithexistingpre-drilledholesfortraditionalmechanicalfastenerscanbesecuredwiththeuseofstrapandplatewashers.




Steel 4 4 4

Steel Decking 4 4 4


Features & Benefits• FAST One-Step Fixing of metal, nylon and velcro straps for ductwork, cable

bunches and fixture installations.• Suitable to span wide mounting holes in cable suspension brackets or

switchboxes up to 8mm diam.• To reinforce mounting holes in brackets and prevent fixture pullover.• Precise hole alignment.• Use with pre-drilled or solid straps and plates.• Suitable for use with CableMaster™ Pulsa™ collated pins.• Choose the pin length to suit the application.• SC6 or HC6 pins recommended.• One handed fixing to concrete, hollow block and steel.




Catenary Wire Bracket AssemblyPart No Description Order QtyCWKBT CatenaryWireBracketAssembly 100CPGCWB CatenaryWireBracketContractorPack(400xbrackets,SC620Pins,FuelCell,200mmx4.8mmBlack) 1

Catenary Wire BracketCableMaster™ Consumables

SpecificationsSteel type CA2S-E.

Steel Thickness2mm providing a high resistance to deformation.

Nominal Fixing Hole Diameter 7.5mm

DescriptionReinforcedsteelanglebracket,withclosedeyeforcatenarywireandcableinstallationswhenfixingtoconcrete,concreteblockandsteel.Suitableforlighttomediumduty,closetoceilingapplications.




Steel 4 4 k

Steel Decking 4 4 4


Installation Procedure1. Place bracket assembly into the pin guide.

2. Depress pin guide against work surface, fix bracket

into position.

3. Attach cables and wires as required.

Features & Benefits• For catenary wire, cable, and hanger rod installations when fixing to

concrete, hollow block and steel.• Improved clampdown to work surface with dimpled baseplate.• Optimum pin penetration with cushioned base.• Strengthening ribs reduce bracket twist and deformation.• Rounded edges to prevent cable damage.• Three methods of installation. - Fast fixing with CableMaster™ Pulsa™ gas tool.

- TyMaster™ tool installation (See page 52).

- Traditional drill and anchor method.

• Suits light to medium duty fixing applications. (see performance table)

• Fix from the ground with pole tool.• Eye size - 7mm.

Performance Table*Load Capacity (Tension)

Product - Concrete 32MPaCat Brkt Pulsa assembly, SC620 Pin 10kgCat Brkt Pulsa assembly, HC617 Pin 14kg

*Notes:1. Values represent the maximum recommended working load in tension.2. A minimum of 5 fastenings per fastened unit must be used.

3. Results have been achieved with a CableMaster™ tool.4. All visible failures must be replaced and a new fixing set away from any spalled concrete.5. Tension loads provided are for static load situations only.6. Job-site testing may be required to determine actual achievable job-site values7. Minimum edge distance 75mm. Minimum spacing between fixings 50mm.



Features & Benefits•Cordless-selfpowered,nosetuptimerequired•Sequentialactuation-safeoperation•Depth-of-drive(indicatedontopofthetool)•Lock-outfeature(security)•Belthook•Flaredfastenerguidedesignedforpartitioningtrackwork•5kgactuationforce•Softcushionedgrip•Voltageindicatorlight•Compactcarryingcase•Wellbalanced•Heatsensorcontrolsamountofgasinjected,relativetotheambient

temperature•Electronicallycontrolledfuelinjection•Lowmaintenance.DesignedtoworkinallAustralianconditions•In-carchargeraccessory

Gas

Tech

nolo

gy S

yste

ms

DescriptionTheRamset™TrakMaster™Pulsa™Technologytoolisthefastestmethodofinstallingpartitioningtrack,pestcontrolmeshandformworksystems.Cordlessandquicktosetup,userscanmovequicklyandeffectivelywithoutrestriction.

TrakMaster™For Ceiling, Partitioning & General

Contractors

Related ProductsDrive Pins & Fuel Cells

SpecificationsWeight 3.7kgHeight 383mmLength 295mm

Magazine Capacity20(+3)pinmagazine,[40(+3)pinmagazineaccessory]

Impact Force 82JActuation Pressure 5kgOverdrive 4mmIntermittent Operation 2pinspersecondFuel Cell Life 650pins(approx)Battery Charge Capacity 1,000pins(approx)Battery Voltage 6VBattery Amperage 600mABattery Charge time 1hourPower Regulation AutomaticOperating Temperature Range -5°C to 49°CSubstratesConcrete,CompositeSteelDecking,SolidBrick,PrecastConcrete,SteelPre-stressedconcrete,HollowBlockWall,ReinforcedConcrete,ReinforcedPrefabricatedConcrete



Removable20 Pin Magazine

(40 Pin Magazine Available)


AccessoriesPart No Description Order Qty333700 MagneticFastenerGuide(forusewith25mmwashers011204) 1337700 TrakMaster™FastenerGuide 1010670 40PinMagazine 1TMBP Battery 1900507 In-carCharger 1PA1613 SafetyGlasses 1TMBC ReplacementCharger 1TMBCPS AC/DCAdaptor 1B20544L GasToolDegreaserandLubricant 1


TrakMaster™For Ceiling, Partitioning & General

Contractors

Standard Operating ProcedureAlwaysreadandunderstandtheinstructionmanualbeforeattemptingtooperateaRamset™GasTechnologyTool.1. Firstinsertthefuelcellandbatteryintothetool.2. Insertthecollatedfastenersintothemagazine.3. Ifthemagneticwasheradaptorisfitted,thewashershouldbeplacedintheadaptorwithoutcompressingthefrontendofthetool.4. Thetoolshouldthenbecompressedagainsttheworksurface.(Makingsurethatthetoolisperpendiculartotheworksurface).5. Oncethetooliscompressedthetriggercanbeactuatedandthefastenerisdriventhroughthematerialbeingfastenedandintothesubstrate.

TrakMaster™

Part No Description Order QtyTRAKMASTER TrakMaster™Pulsa™Tool+2xbatteries 1

Kitincludes:TrakMaster™Pulsa™Tool,highimpactcarrycase,2batteries,batterycharger,safetyglasses,allenkey,dustcoverandinstructionmanual

Trades & Applications Ceiling and Partitioning Formwork Pest Control Contractor Contractor ContractorTrack to concrete 4

Track to steel 4 Plywood to steel 4

Sacrificial steel formwork to steel 4

Pest control mesh to concrete 4


Gas

Tech

nolo

gy S

yste

ms

Part No Description Length Order QtyC620 Fixingtimbertoconcrete/lightgaugesteel 20mm 500C625 Fixingtimbertoconcrete/lightgaugesteel 25mm 500C630 Fixingtimbertoconcrete/lightgaugesteel 30mm 500C635 Fixingtimbertoconcrete/lightgaugesteel 35mm 500

10stripcollation(suitableforusein20and40pinmagazines)+1xFuelCell

TrakMaster™

Consumables

Part No Description Length Order QtyHC615 PremiumSteelPin 15mm 500HC617 PremiumHardConcrete/Steel 17mm 500SC620 PremiumHardConcrete/Steel 20mm 500HC622 PremiumHardConcrete/Steel 22mm 50010stripcollation(suitableforusein20and40pinmagazines)+1xFuelCell

All-purpose Pin Range for Steel and Concrete FixingDrive Pins designed for fastening to standard strength concrete, masonry and steel up to a maximum of 6mm.

Heavy Duty Pin Range for Steel and Hard Concrete FixingThe Ramset™ range of Premium Drive Pins has been designed for steel and hard concrete applications.

SpecificationsRaw Material CarbonSteelCorrosion Protection Zinc Electroplated (Minimum coating 5µm)Nominal Head Diameter 6.3mmNominal Shank Diameter 2.6mm(C620Steppedshank2.6/2.2mm)Shear Strength 1120N/mm2


Hardness 52-56HRC

SpecificationsRaw Material CarbonSteelCorrosion Protection Zinc Mechanically Plated (Min coating 10µm)Nominal Head Diameter 6.4mmNominal Shank Diameter 3.0mm/2.7mmShear Strength 1200N/mm2


Hardness 53-56HRC




Part No Description Order Qty011204 Washer25mm 1000

TrakMaster™

Consumables

Part No Description Length Order QtyPLY138P HardSteelTwistPin 35mm 100010stripcollation(suitableforusein20and40pinmagazines)+2xFuelCells

Spiral Knurled Pins for Fixing Plywood and Particleboard to SteelRamset’s spiral knurled drive pins are designed for fastening plywood and other timbers to steel while providing excellent holding loads. These pins are ideal for applications such as formwork shuttering.

SpecificationsRaw Material GalvanisedSteelCorrosion Protection Zinc GalvanisedNominal Diameter 25mmNominal Diameter 1.25mm

WashersWashers are specially designed for use with the magnetic fastener guide adaptor. They are ideal for fastening thin materials and provide good clamping loads due to their large surface area.

SpecificationsRaw Material CarbonSteelCorrosion Protection Zinc Mechanically Plated (Min coating 5µm)Nominal Head Diameter 6.4mmNominal Shank Diameter 2.7mmShear Strength 1120N/mm2


Hardness 50-56HRC



Features & Benefits•Cordless-selfpowered,nosetuptimerequired•Sequentialactuation-safeoperation•Toolautomaticallyresetspiston•Narrownoseandprofile•Softcushionedgrip•Carryingcase•Wellbalanced•Mechanicalfuelinjection•Lowmaintenance

Gas

Tech

nolo

gy S

yste

ms

DescriptionForfastinstallationofpartitioningandtrack,usetheRamset™TrakFast™gastooltoprovidehighvolumerepetitivefixingintoarangeofbuildingmaterials.

TrakFast™Ceiling, Partitioning and General

Contractors


SpecificationsWeight 4.1kgHeight 450mmLength 397mmMagazine Capacity 40(+2)pinmagazineImpact Force 77JActuation Pressure 5kgIntermittent Operation 2pinspersecondFuel Cell Life 1,100pins(approx)Battery Charge Capacity 3,000pins(approx)Battery Voltage 6VBattery Amperage 600mABattery Charge time 2.5hoursPower Regulation AutomaticOperating Temperature Range -5°C to 49°CSubstratesConcrete,CompositeSteelDecking,SolidBrick,PrecastConcrete,SteelPre-stressedConcrete,HollowBlockWall,ReinforcedConcrete,ReinforcedPrefabricatedConcrete

MechanicalFuel Injection40 Pin Magazine


AccessoriesPart No Description Order QtyPA1613 SafetyGlasses 1B20542 Battery 1TFBC BatteryCharger 1TMBCPS AC/DCAdaptor 1TFGAS ReplacementFuelCell 6900507 In-carCharger 1B20544L GasToolDegreaserandLubricant 1


TrakFast™Ceiling, Partitioning and General

Contractors

Standard Operating ProcedureAlwaysreadandunderstandtheinstructionmanualbeforeattemptingtooperateaRamset™GasTechnologyTool.1. Firstinsertthefuelcellandbatteryintothetool.2. Insertthecollatedfastenersintothemagazine.3. Thetoolshouldthenbecompressedagainsttheworksurface.(Makingsurethatthetoolisperpendiculartotheworksurface).4. Oncethetooliscompressedthetriggercanbeactuatedandthefastenerisdriventhroughthematerialbeingfastenedandintothesubstrate.

TrakFast™

Part No Description Order QtyTF1100 TrakFast™Tool+1battery 1

Kitincludes:TrakFast™Tool,highimpactcarrycase,1xbattery,batterycharger,safetyglassesandinstructionmanual

Trades & Applications Ceiling & Partitioning Contractor Track to concrete 4

Track to steel 4


Part No Description Length Order QtyFPP012 1/2”StandardPin 13mm 1000FPP034B 3/4”StandardPin 19mm 1000FPP100 1”StandardPin 25mm 1000FPP114 11/4”StandardPin 32mm 1000


Part No Description Length Order QtyFPP034T 3/4”Pinwithbreakawaystrip 19mm 1000FPP100T 1”Pinwithbreakawaystrip 25mm 1000FPP112T 11/2”Pinwithbreakawaystrip 38mm 1000


Gas

Tech

nolo

gy S

yste

ms

TrakFast™

Consumables

Standard Duty Pin RangeDrive pins designed for fastening partitioning track to standard strength concrete, masonry and steel.

Breakaway Pin Range for Concrete FixingDrive pins collated in a breakaway strip. Upon fastening the plastic collation strip is eliminated leaving a clean flush pin fixing. These pins are ideal for applications requiring a flush fixing, or where any protrusions from the fixture surface may cause problems.

SpecificationsRaw Material CarbonSteel

Corrosion ProtectionZinc Mechanically Plated (FPP034B are coated with a proprietry black finish (Minimum coating 5µm)

Nominal Head Diameter 6.0mm(6.4mmforFPP012)Nominal Shank Diameter 2.8mm(2.9mmforFPP012)Shear Strength 1120N/mm2


Hardness 50-56HRC

SpecificationsRaw Material CarbonSteelCorrosion Protection Zinc Mechanically Plated (Min coating 5µm)Nominal Head Diameter 6.0mmNominal Shank Diameter 2.8mmShear Strength 1120N/mm2


Hardness 50-56HRC




TrakFast™

Consumables

Part No Description Length Order QtyFPP012S 1/2”HeavyDutySteel/Concrete 13mm 1000


Heavy Duty Pin RangeDrive pin designed for fastening partitioning track to steel.

SpecificationsRaw Material CarbonSteelCorrosion Protection Zinc Electroplated (Minimum coating 5µm)Nominal Head Diameter 6.4mmNominal Shank Diameter 3.0mm/2.7mm(SteppedShank)Shear Strength 1120N/mm2


Hardness 50-56HRC



InsulFast™ GTGas Technology Systems

Features & Benefits• The fastest insulation fixing system• Virtually no recoil!• 3 times less cocking force required than explosive powered tools• Faster install than explosive powered tools - lower in place cost• Automatic power adjustment• Fixes to concrete and steel without the need for adjustment• Compatible with all major insulation types• Low insertion force• Textured face for compatibility with rendering applications• Sizes to suit soft and rigid insulation from 25mm to 100mm• 100mm capacity available early 2011• Soft insulation with thickness greater than 75mm may be compressed.

Gas

Tech

nolo

gy S

yste

ms

DescriptionThefastestinsulationfixingsystem!Thisnewgastechnologysystemprovideseffortlessoverheadfixingofinsulationwithvirtuallynorecoil.Thelowtoolcompressionforceenhancesusercomfort.


SpecificationsWeight 3.4kgHeight 383mmLength 295mmImpact Force 100JActuation Pressure 3.5kgIntermittent Operation 1pinpersecondFuel Cell Life 500pins(approx)Battery Charge Capacity 1,000pins(approx)Battery Voltage 6VBattery Amperage 600mABattery Charge time 1hourPower Regulation AutomaticOperating Temperature Range -5°C to 49°CSubstratesConcrete,CompositeSteelDecking,SolidBrick,PrecastConcrete,SteelPre-stressedConcrete,HollowBlockWall,ReinforcedConcrete,ReinforcedPrefabricatedConcrete



Low Compression Force

Virtually No Recoil


InsulFast™ GTGas Technology Systems


InsulFast™ GTPart No Description Order QtyINSULFASTGT InsulFast™GTPulsa™Tool+2xBatteries 1

Kitincludes:InsulFast™GTPulsa™tool,highimpactcarrycase,2xbatteries,batterycharger,safetyglasses,allenkey,dustcoverandinstructionmanual

AccessoriesPart No Description Order QtyPA1613 SafetyGlasses 1TMBP Battery 1900507 In-carCharger 1TMBC ReplacementCharger 1TMBCPS AC/DCAdaptor 1B20544L GasToolDegreaserandLubricant 1

Installation Procedure1. Place the fastener assembly over the front end of the tool without compressing the fastener guide. 2. Force the fastener assembly through the insulation and compress the tool completely. 3. Once the fastener assembly has reached the base material, (concrete / steel), release the pressure on the tool and allow the fastener guide to fully extend. (By moving the tool away from the insulation by approximately 15mm). 4. While keeping hands away from the front of the tool, fully compress the tool against the insulation. 5. Immediately pull the trigger once the tool is fully compressed. 6. Remove the tool.

Trades & Applications Installation Ceiling & Partitiioning Installers ContractorInsulation to concrete 4 4

Insulation to steel 4 4


InsulFast™ GTConsumables

Gas

Tech

nolo

gy S

yste

ms

Insulation Fasteners for Concrete, Masonary and SteelPart No. Rigid Insulation Soft Insulation Fastener Order

Thickness Thickness Colour * QtyIG625 25mm 25mm – 30mm Natural (White) 400IG625B 25mm 25mm – 30mm Black 400IG638 38mm 38mm – 45mm Natural (White) 350IG650 50mm 50 mm – 55mm Natural (White) 300IG650B 50mm 50 mm – 55mm Black 300IG675 75mm 75mm – 85mm Natural (White) 250IG675B 75mm 75mm – 85mm Black 250IG6100# 100mm 100mm – 110mm Natural (White) 200

Fastener SpecificationFastener Body Material High Density Polyethylene (HDPE)Holding Diameter 60 mmLengths Available 25 mm to 100 mmDrive Pin Material Carbon Steel Drive Pin Plating Mechanical Zinc Plate Drive Pin Shear Strength 8.0 kN

Fuel Cells are included with all fasteners.* Other sizes and colours such as silver, to a maximum of 75mm in length are available on request. Minimum order quantities and lead times apply.# Available early 2011

The recommended load (kN) are calculated from the mean ultimate load and a factor of safety higher than 4.A minimum of 4 fixings per fastened unit are required.As concrete composition varies jobsite testing is recommended.

Technical Load DataPart No. Concrete Strength Tensile Working Load Limit WLLIG625 25 – 45 MPa 0.15 kNIG625B 25 – 45 MPa 0.15 kNIG638 25 – 45 MPa 0.15 kNIG650 25 – 45 MPa 0.15 kNIG650B 25 – 45 MPa 0.15 kNIG675 25 – 45 MPa 0.15 kNIG675B 25 – 45 MPa 0.15 kNIG6100 25 – 45 MPa 0.15 kN

Extruded Polystyrene Polyester Fibreglass / Rockwool Expanded Polystyrene

Compatible Insulation



Notes


Powder ActuatedSystems

With over 50 years of experience in designing

and manufacturing powder actuated tools and

consumables, Ramset™ Powder Actuated

fastening systems are innovative, powerful, easy

to use and specifically designed for Australian

applications. These tools provide a fast fixing

method for fastening many common building

materials to concrete, masonry and steel.

Tools in this range include:

• FrameMaster™ (TS750P)

• FormMaster™

• JobMaster™

• FrameBoss™

• TyMaster™

• Rocket



Powder ActuatedSystems


ContentsPowder Actuated Systems

Selection Guide 40

FrameBoss™ 42

Rocket 46

FrameMaster™ (TS750P) 48

FormMaster™ 50

TyMaster™ 52

JobMaster™ 54

Drive Pins & Power Loads 56

Fastening Principles 38


How to select a Ramset™ Drive Pin to directly fasten an object to STEEL

Powder Actuated Technology - How it works

Fixing to concreteAs the fixing enters the concrete, extreme pressure and heat are created. This creates a bond that provides high loading strength in concrete.

Edge distanceDo not fix closer than 75mm from the edge of concrete. If the concrete cracks, the fixing may not hold.

Recommended minimum fixing spacingSetting fixings too close together can cause the concrete to crack. The recommended minimum distance between fixings is 75mm. Never attempt a fixing application too close to another fixing as this could affect the previously inserted fixing’s embedment.

Concrete thicknessIt is important that the concrete be at least three times as thick as the fixing penetration. If the concrete is too thin, the compressive forces forming at the fixing’s point can cause the free face of the concrete to break away. This creates a dangerous condition from flying concrete and / or the fixing and also results in a reduction of fastener holding power.

How to select a Ramset™ Drive Pin to directly fasten an object to CONCRETE

Fixing to steelThe resilience of steel provides a clamping effect to the fixing. This combined with the tremendous heat that is created, provides a welding and clamping effect to give maximum holding power.

Edge distanceThe recommended edge distance for a fixing to the edge of steel is 13mm. Never fire the tool within 13mm of the edge of a steel base material because the steel may bend or break off, allowing the fixing to ricochet.

Recommended minimum fastener spacingThe recommended minimum distance between fixings is 25mm. Never attempt a fixing application too close to another fixing as this could affect the previously installed fixing’s embedment.

Steel thicknessDo not fasten into steel base material thinner than the fastener shank diameter. Holding power may be reduced and the fastener may be overdriven.

As a guide when:• Fixing into steel - min. steel thickness = 4mm

Ramset™ Powder Actuated Technology uses a captive piston to transfer the energy from the power load to the fastener. In this way the majority of any excess energy, which is produced by the power load, is absorbed within the tool by the buffer.Ramset™ Powder Actuated tools are powerful and reliable which allows them to fasten to steel, concrete and masonry year after year.


Thickness + 25mmof material

(M)

M


Thickness + Steel + 6mm of material Thickness point

(M) (T) allowance

M

T

1. Firing Pin2. Power Load3. Captive Piston4. Buffer5. Powder Actuated Fastener

4 3 2 15

Fastening PrinciplesPowder Actuated Systems

Fast

enin

g Pr

inci

ples


NotesPow

der Actuated Systems

Product Range

Page

Ref

eren

ce

Fram

eBos

s™

Rock

et

(TS7

50P)

Form

Mas

ter™

TyM

aste

r™

JobM

aste

r™

Standard Drive Pins For Concrete, Masonry & Steel

564

25 to 75mm

4

25 to 50mm

4

25 to 75mm

4

25 to 100mm

4

25 to 32mm

4

25 to 75mm

Timber Formwork Pins For Concrete & Easy Pin Removal

564

60 to 75mm

▲

4

25 to 75mm

4

25 to 100mm

4

25 to 32mm

4

25 to 75mm

Premium Drive Pins For Structural Steel

574

25 to 75mm

▲

●

25 to 75mm

4

25 to 75mm

▲

●

25 to 75mm

Washered Drive Pins For Concrete , Masonry & Steel

574

25 to 75mm

4

25 to 32mm

4

25 to 75mm

4

25 to 75mm

4

25 to 32mm

4

25 to 75mm

Standard Collated Drive Pins For Concrete, Masonry & Steel

444

25 to 60mm

▲ ▲ ▲ ▲ ▲

Premium Collated Drive Pins For Concrete, Masonry & Steel

444

25 to 60mm

▲ ▲ ▲ ▲ ▲

Angle Bracket & Threaded Rod Hanger Assemblies

58 4 4 4 ▲ 4 4

Drive Pins For Fixing Thin Steel To Steel

58 4 4 4 4 4 4

Drive Pins For Fixing Thin Steel To Steel

58 4 ▲ ● 4 ▲ ●

Insulation Fasteners For Concrete, Masonry & Steel

454

With Adaptor

▲ ▲ ▲ ▲ ▲

Soft Washered Membrane Fastener

59 4 ▲ 4 4 ▲ 4


4 Recommended ● Maybe possible dependant on substrate ▲ Not suitable

Selection GuidePowder Actuated Systems

Pow

der

Actu

ated

Sys

tem

s

Fram

eMas

ter™

42 46 48 50 52 54


Powder Actuated System

sSelection Guide

Powder Actuated Systems

SP12 SP12SC925

SC925CSC930CSC930

SC930CSC930 SC950C SC960C

PIN Part No.

PIN Part No. RDU99LDU75LWU75

SP12 SP12SC925

SC925CSC930CSC930

SC930CSC930 SC950C SC960C

PIN Part No.

PIN Part No. RDU99LDU75LWU75

Fastener Selection and Correct SettingThe correct selection and setting of Powder Actuated Fasteners is critical with all tools to ensure a secure fixing and long tool life.

The correct setting of the fastener should be as detailed in the diagrams to avoid excessive overdrive and a secure fix.

Where possible, a washer (Part No: RCD16F) or a washered fastener should be used. (Application permitting, to reduce overdrive and produce maximum clamping force). Repeated excessive overdrive will result in damage and short life of tool parts.

Powerload Selection Guide - ConcreteTool 20 MPa Concrete

Low Strength30 MPa Concrete Medium Strength

40 MPa Concrete High Strength

FrameBoss™ PLSGR22 PLSYW22 PLSRD22FrameMaster™ TS750P PLSGR22 PLSYW22 PLSRD22FormMaster™ PLSGR22 PLSYW22 PLSRD22JobMaster™ PLCGR22S PLCYW22S PLCRD22STyMaster™ PLSGR22 PLSYW22 PLSRD22Rocket PLSGR22 PLSYW22 PLSYW22

This chart is to be used as a guide only.Ramset™ recommends to always start a new application with the minimum powerload strength, and if applicable, the tool at minimum power setting, then gradually increase power with load strengths, and if applicable, a combination of power adjustment setting powerload and pin length.


FrameBoss™

Fully Automatic Tool

SpecificationWeight 3.0 kg (3.2 kg with magazine)Impact Force 380JFixing Capacity:Timber to Concrete 50mmTimber to Steel 50mmMetal to Concrete 3mmMetal to Steel 3mmPin Capacity up to 75mmOverall Length 490mmSubstrates Concrete, Steel, Masonary

Features & Benefits• Automatic piston return • No manual cycling required• Easy to maintain on site• 10 Pin magazine and single shot fastener guide• 75mm single shot capacity• 60mm magazine capacity• 380J maximum impact energy• Power adjustment• Trigger lock• Hand guard• Cushioned rubber grip

Pow

der

Actu

ated

Sys

tem

s

DescriptionThe Ramset™ FrameBossTM is a fully automatic powder actuated tool, which is capable of fixing 10 pins without the need to reload or cycle the tool. The automatic piston return system and 10 pin magazine allow for faster fixing rates with less effort. The magazine can be adjusted to lock into a number of positions to allow the tool to be used in confined spaces. The FrameBossTM tool is also supplied with a single shot fastener guide to allow the tool to be used with longer fasteners and assembles such as brackets and clips. With a huge 380 Joules of impact energy coupled with power adjustment, the tool can be used in a wide variety of applications e.g. Timber framing, formwork and the fixing of steel track. FrameBossTM is designed to save you time and money.

10 pin magazine

Automatic piston return

Cushioned rubber grip

Power adjustmentQuick change fastener guide

Related ProductsPower LoadsDrive PinsTool AccessoriesDrive Pin Accessories

75mm single shotfastener guide includedin tool kitFAST FIXING!


FrameBoss™ AccessoriesPart No Description Order QtyPA37037 Piston 1010982 Piston Return Spring (x2) 1010983 Piston Buffer (x2) 1PA37040 Fastener Guide Assembly 1PA37038 Magazine Assembly 1PA9316 PA Lubricating and Release Oil 1PBT Drive Pin Removal Tool 1PA1613 Safety Glasses 1PA37023 Spall Shield 1PAWS8 Explosive Tool in Use - Safety Warning Sign 1

FrameBoss™

Fully Automatic Tool

Power Load StripsPart No Colour Strength Order QtyPLSGR22 Green Weak 100PLSYW22 Yellow Medium 100PLSRD22 Red Strong 100


s

Trades & Applications Residential Home Formwork Ceiling & Partitioning Bricklayer Builder Contractor Contractor Timber to concrete 4 4

Timber to steel 4 4

Sacrificial steel formwork to steel 4 Steel track to concrete & steel 4 4 Brick Ties to concrete & steel 4 4

FrameBoss™

Part No Description Order QtyFRAMEBOSS FrameBoss™ tool kit 1

Kit includes: FrameBoss™ tool, steel tool case, single shot fastener guide, magazine, safety glasses, maintenance kit and instruction manual.

Standard Operating ProcedureAlways read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First cycle the tool and insert the power load strip.2. Insert the correct fastener or collated fasteners, (without compressing the front of the tool).3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.


FrameBoss™

Collated Drive Pins

*Refer to page 56 for more fasteners that are suitable for use with the FrameBossTM Tool

Part No Drive Pin Length Max Fixture

(thickness to steel)Max Fixture

(thickness to concrete)Order Qty

SC925C 25mm 12mm 2mm 500SC930C 30mm 18mm 5mm 500SC940C 40mm 30mm 15mm 300SC950C 50mm 35mm 25mm 300SC960C 60mm 45mm 35mm 300

Collated Pins for Fixing to Structural Steel and Hard ConcreteThe Ramset™ range of Premium Collated Drive Pins is designed for use with the FrameBoss™ magazine for fastening to steel and hard concrete applica-tions. The design of these drive pins allows them to penetrate hard materials with less power while the strengthened shank greatly reduces the possibility of column collapse.

Part No Drive Pin Length Max Fixture (thickness to steel)

Max Fixture (thickness to concrete)

Order Qty

C925C 25mm 12mm 2mm 500C930C 30mm 18mm 5mm 500C940C 40mm 30mm 15mm 300C950C 50mm 35mm 25mm 300C960C 60mm 45mm 35mm 300

SpecificationsRaw Material Carbon Steel (Plastic Collation)Corrosion Protection Zinc Electroplated (Minimum coating 7µm)Nominal Head Diameter 8.8mmNominal Shank Diameter 3.7mmShear Strength 1120N/mm2


Hardness 50 -55HRC

Standard Collated Drive Pins for Fixing to Concrete and MasonaryCollated Drive Pins designed for use with the FrameBoss™ magazine for fastening to standard strength concrete, masonry and steel up to a maximum of 8mm.

SpecificationsRaw Material Carbon Steel (Plastic Collation)Corrosion Protection Zinc Electroplated (Minimum coating 7µm)Nominal Head Diameter 8.8mmNominal Shank Diameter 4.0mm / 3.7mmShear Strength 1240N/mm2


Hardness 54 -58HRC

Pow

der

Actu

ated

Sys

tem

s



FrameBoss™

InsulFastTM Accessory Kit

DescriptionThe Ramset™ InsulFast™ adaptor kit transforms the FrameBoss™ tool into a specialist insulation fixing tool with automatic piston return. The FrameBoss™ tool in this configuration is capable of fastening insulation from 40mm to 120mm without compression.

Accessories Part No Description Order QtyPA11030 InsulFast™ adaptor kit includes Fastener Guide Assembly, Piston and Piston Return Spring 1011031 Piston - includes Piston Return Spring 1011032 Piston Return Spring x 2 1

Fastener SpecificationFastener Body Material High Density Polyethylene (HDPE)Holding Diameter 60 mm (90 mm for CI960)Lengths Available 40 mm to 120 mmDrive Pin Material Carbon Steel Drive Pin Plating Electroplated Zinc Drive Pin Shear Strength (Ultimate) 12.0 kN

Insulation Fasteners for Concrete, Masonary and SteelPart No. Rigid Insulation Soft Insulation Fastener Order Thickness Thickness Colour QtyCI640 40mm 40mm – 45mm Natural (White) 200CI650 50mm 50mm – 55mm Natural (White) 200CI960 60mm 60 mm – 65mm Black 100CI670 70mm 70 mm – 75mm Natural (White) 200CI6100 100mm 100mm – 110mm Natural (White) 100CI6120* 120mm 120mm – 130mm Natural (White) 100

Technical Load DataPart No. Concrete Strength Tensile Working Load Limit WLLCI640 25 – 45 MPa 0.30 kNCI650 25 – 45 MPa 0.30 kNCI960 25 – 45 MPa 0.30 kNCI670 25 – 45 MPa 0.30 kNCI6100 25 – 45 MPa 0.30 kNCI6120* 25 – 45 MPa 0.30 kN

* Available upon request.

The recommended loads (kN) are calculated from the mean ultimate load and a factor of safety higher than 4.A minimum of 4 fixings per fastened unit are required.* Available upon request.

NEW


s



RocketAutomatic Short Pin Tool

SpecificationsWeight 2.2kgImpact Force 360JFixing Capacity:Timber to Concrete 25mmTimber to Steel 35mmMetal to Concrete 3mmMetal to Steel 3mmPin Capacity up to 50mmOverall Length 435mmSubstrates Concrete, Steel, Masonary

Features & Benefits• Fast - 10 shot strip feed with automatic advance• Optimum fixing - power adjustment ensures consistent performance• Power - adjustable for use with steel or concrete• Lightweight - minimal operator fatigue• Minimal maintenance

Pow

der

Actu

ated

Sys

tem

s

DescriptionThe Ramset™ Rocket is the fastest high volume, short pin tool. This powerful fully automatic tool performs high volume repetitive short pin fixings with ease.


Automatic piston return

Power adjustment


*Refer to page 56 for fasteners that are suitable for use with the Rocket Tool


RocketAutomatic Short Pin Tool

Rocket AccessoriesPart No Description Order QtyA1010 Piston 1A1049A Fastener Guide Assembly 1A1130A Buffer Assembly 1PA9316 PA Lubricating and Release Oil 1PBT Drive Pin Removal Tool 1PA1613 Safety Glasses 1PAWS8 Explosive Tool in Use - Safety Warning Sign 1


s

RocketPart No Description Order QtyROCKET Rocket Tool 1

Kit includes: Rocket tool, high impact carry case, safety glasses, maintenance kit and instruction manual.

Standard Operating ProcedureAlways read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First insert the power load strip.2. Insert the correct fastener, (without compressing the front of the tool).3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.

Trades & Applications Residential Home Ceiling & Partitioning Bricklayer Builder Contractor Steel framing to concrete 4

Steel track to concrete & steel 4 Brick Ties to concrete & steel 4



FrameMaster™

TS750P - Power Adjustable Tool


Features & Benefits• Fast – 10 shot strip feed with automatic advance• Optimum fixing – positive power adjustment ensures

consistent performance• Power – adjustable for use with steel or concrete• Minimal maintenance – easy to dismantle & clean to reduce downtime• Long Life – long life piston & buffer

Pow

der

Actu

ated

Sys

tem

s

DescriptionThe Ramset™ FrameMaster™ TS750P is the timber framing expert. A power adjustable tool designed for fixing timber framing to concrete and general repetitive work.


*Refer to page 56 for fasteners that are suitable for use with the FrameMasterTM TS750P Tool

Power adjustment



FrameMaster™ TS750P AccessoriesPart No Description Order QtyPA27833 Piston Assembly - Standard 1PA27432 Piston Assembly - High Power 1PA27831 Fastener Guide Assembly 1PA9316 PA Lubricating and Release Oil 1PBT Drive Pin Removal Tool 1PA1613 Safety Glasses 1PA27580 Spall Shield 1PAWS8 Explosive Tool in Use - Safety Warning Sign 1

FrameMaster™

TS750P - Power Adjustable Tool


s

FrameMaster™ TS750PPart No Description Order QtyTS750P FrameMaster™ TS750P tool 1

Kit includes: FrameMaster™ tool, high impact carry case, safety glasses, maintenance kit and instruction manual.

Standard Operating ProcedureAlways read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First cycle the tool and insert the power load strip.2. Insert the correct fastener, (without compressing the front of the tool).3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.


Trades & Applications Residential Home Formwork Bricklayer Builder Contractor Timber to concrete 4 4

Timber to steel 4 4 Brick Ties to concrete & steel 4 4


FormMaster™

The Formworker’s Tool


Features & Benefits• Fast – 10 shot strip feed with automatic advance• Optimum fixing – positive power adjustment ensures

consistent performance• Power – adjustable for use with steel or concrete• Front barrel safety grip & hand guard – all day use comfort• Minimal maintenance – easy to dismantle & clean to reduce downtime• Long Life – long life piston & buffer

Pow

der

Actu

ated

Sys

tem

s

DescriptionThe Ramset™ FormMaster™ is the professional’s choice for long pin fixing.A high powered fastening system with the power and comfort to meet the demands of the timber and steel formwork industry and heavier repetitive fixing jobs.


*Refer to page 56 for fasteners that are suitable for use with the

FormMasterTM Tool

Power adjustment


HIGH POWER!


FormMaster™

The Formworker’s Tool


s

FormMaster™

Part No Description Order QtyFORMMASTER FormMaster™ Tool 1

Kit includes: FormMaster™ tool, high impact carry case, safety glasses, maintenance kit and instruction manual.

FormMaster™ AccessoriesPart No Description Order QtyPA28811 Piston Assembly 1PA312860 Buffer x 5 1PA28816 Fastener Guide Assembly 1PA9316 PA Lubricating and Release Oil 1PBT Drive Pin Removal Tool 1PA1613 Safety Glasses 1PA310000 Spall Shield 1PAWS8 Explosive Tool in Use - Safety Warning Sign 1


Trades & Applications Residential Home Formwork Bricklayer Builder Contractor Timber to concrete 4 4

Timber to steel 4 4 Brick Ties to concrete & steel 4 4

Sacrificial steel formwork to steel 4

Standard Operating ProcedureAlways read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First cycle the tool and insert the power load strip.2. Insert the correct fastener, (without compressing the front of the tool).3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.


TyMaster™

The Overhead Tool

Typical PropertiesWeight 2.3kgImpact Force 320JFixing Capacity:Metal to Concrete 3mmMetal to Steel 3mmPin Capacity up to 32mmOverall Length (including pole) 2000mmSubstrates Concrete, Steel, Masonary

Features & Benefits• Fast 10 shot strip feed with automatic advance• Lightweight – reduced fatigue in overhead operation• Fully automatic – high install rate• Safe – patented “Breech lockout” means it can only fire in

vertical up position• Minimal maintenance

Pow

der

Actu

ated

Sys

tem

s

DescriptionThe Ramset™ TyMaster™ is an effortless, overhead fixing, fully automatic tool with extension pole for efficient, remote, overhead fixing of suspended ceilings and services installations.



TyMasterTM Tool

OVERHEAD FIXING!

Automatic piston return Dedicated

pole tool

Automatic charge advance


TyMaster™

The Overhead Tool

TyMaster™ AccessoriesPart No Description Order Qty653116 Piston Standard 1PAT1085 Piston High Power 1653021 Buffer x 3 1653106 Fastener Guide Assembly 1653035 Spall Shield 1PA9316 PA Lubricating and Release Oil 1PBT Drive Pin Removal Tool 1PA1613 Safety Glasses 1PAWS8 Explosive Tool in Use - Safety Warning Sign 1


s

TyMaster™

Part No Description Order QtyTYMASTER TyMaster™ Tool 1

Kit includes: TyMaster™ tool, high impact carry case, 1560mm (3 x 520mm) pole extension,safety glasses, maintenance kit and instruction manual.

Standard Operating ProcedureAlways read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First insert the power load strip in the tool. 2. Load the correct drive pin, (without compressing the front of the tool).3. Carefully raise the tool to the ceiling and depress the barrel assembly where the fastening is to be made. 4. While holding the tool perpendicular and compressed against the work surface, forcibly push upwards on the pole handle to fire the tool.


Trades & Applications Ceiling & Partitioning Electrical Contractor ContractorFixing of suspended ceilings 4

Light duty cable tray 4

Catenary wire fixings 4


JobMaster™

General Purpose Tool

Typical PropertiesWeight 2.2kgImpact Force 350JFixing Capacity:Timber to Concrete 50mmTimber to Steel 50mmMetal to Concrete 3mmMetal to Steel 3mmPin Capacity up to 75mmOverall Length 375mmSubstrates Concrete, Steel, Masonary Features & Benefits

• Versatile – suitable for most applications• Minimal maintenance – easy to dismantle & clean, to reduce downtime• Power – determined by the power load used• Operation – single shot

Pow

der

Actu

ated

Sys

tem

s

DescriptionThe Ramset™ JobMaster™ is the amazing all rounder, powerful general purpose tool for the less frequent user – essential for every contractor’s toolbox.



JobMasterTM Tool

Simple single shot design



JobMaster™ AccessoriesPart No Description Order QtyPA28113 Piston Assembly 1PA28235 Buffer x 5 1PA28230 Fastener Guide Assembly 1PA9316 PA Lubricating and Release Oil 1PBT Drive Pin Removal Tool 1PA1613 Safety Glasses 1PA310000 Spall Shield 1PAWS8 Explosive Tool in Use - Safety Warning Sign 1

JobMaster™

General Purpose Tool


s

JobMaster™ Part No Description Order QtyJOBMASTER JobMaster™ Tool 1

Kit includes: JobMaster™ tool, high impact carry case, safety glasses, maintenance kit and instruction manual.

Power Load CartridgesPart No Colour Strength Order QtyPLCGR22S Green Weak 100PLCYW22S Yellow Medium 100PLCRD22S Red Strong 100

Trades & Applications Residential Home Bricklayer Builder Timber to concrete 4

Timber to steel 4 Brick Ties to concrete & steel 4 4

Standard Operating ProcedureAlways read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First cycle the tool and insert the correct drive pin, (without compressing the front of the tool). 2. The power load should then be inserted.3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate.


Drive PinsPowder Actuated Systems

Pow

der

Actu

ated

Sys

tem

s

Part No Drive Pin Length Max Fixture (thickness to steel)


Order Qty

LDU25 25mm 12mm 2mm* 100LDU32 32mm 20mm 7mm 100LDU38 38mm 25mm 12mm 100LDU42 42mm 30mm 20mm 100LDU50 50mm 35mm 25mm 100LDU57 57mm 45mm 35mm 100LDU65 65mm 50mm 45mm 100LDU75 75mm N/A 50mm 100LDU90 90mm N/A 65mm 100LDU99 100mm N/A 75mm 100

* Denotes steel fixture only

Standard Drive Pins for Concrete, Masonry and SteelDrive Pins designed for fastening to standard strength concrete, masonry and steel up to a maximum of 8mm.

Timber Formwork Pins for Concrete and Easy Pin RemovalDrive Pins designed for fastening timber formwork to concrete. When the timber needs to be removed, the small head reduces the force required to strip the timber. The groove in the shank allows the pin to be removed easily with Ramset’s drive pin breaker tool.

Part No Drive Pin Length Max Timber Thickness Order QtyLDU60F 60mm 35mm 200LDU75F 75mm 50mm 200LDU99F 100mm 75mm 200PBT (Pin Breaker Tool) 1

SpecificationsRaw Material Carbon SteelCorrosion Protection Zinc Mechanically Plated (Min coating 6µm)Nominal Head Diameter 7.8mmNominal Shank Diameter 3.7mmShear Strength 1200N/mm2


Hardness 52 - 55HRC



Hardness 52 - 55HRC


PBT (Pin Breaker Tool)




s

Part No Description Max Fixture (thickness to steel)


Order Qty

SC925 Thin Steel to Structural Steel Pin 12mm 2mm 100SC930 Timber to Structural Steel Pin 18mm 5mm 100SC940 Timber to Structural Steel Pin 30mm 15mm 100SC950 Timber to Structural Steel Pin 35mm 25mm 100SC950W Frame & Truss 16mm Washered Pin 35mm 25mm 100SC960 Timber to Structural Steel Pin 45mm 35mm 100SC960W Frame & Truss 16mm Washered Pin 45mm 35mm 100SC970 Timber to Structural Steel Pin 55mm 45mm 100

Premium Drive Pins for Structural SteelRamset’s range of Premium Drive Pins has been designed for steel and hard concrete applications. The design of these drive pins allows them to pen-etrate hard materials with less power while the strengthened shank greatly reduces the possibility of column collapse.

Washered Drive Pins For Concrete, Masonry and SteelWashered Drive Pins designed to provide maximum clamping load while improving tool piston life. Wherever possible the use of washered drive pins is recommended to prevent failure of the material being fastened.

Part No Washer Diameter Drive Pin Length Max Fixture (thickness to concrete)

Order Qty

LWU25 22mm 25mm 2mm* 100LWU32 22mm 32mm 7mm 100LWU75 16mm 75mm 50mm 100LWU25K 16mm 25mm 2mm* 100

* Denotes steel fixture only

SpecificationsRaw Material Carbon SteelCorrosion Protection Zinc Electroplated (Min coating 7µm)Nominal Head Diameter 8.8mmNominal Shank Diameter 4.0 / 3.5mmShear Strength 1240N/mm2


Hardness 54 - 58HRC



Hardness 52 - 55HRC


LWU25K

LWU25



Pow

der

Actu

ated

Sys

tem

s

Part No Description Drive Pin Length Order QtyLAU25 Standard Duty 25mm 100LAU30H Heavy Duty 25mm 100LZU30H Threaded Rod Hanger - M10 25mm 100

SpecificationsRaw Material Carbon SteelCorrosion Protection Zinc PlatedNominal Head Diameter 7.8mmNominal Shank Diameter Various

Angle Bracket and Threaded Rod Hanger AssembliesRamset’s Angle Bracket and Threaded Rod Hanger Assemblies provide a secure fixing point for a wide variety of applications.

Drive Pins For Fixing Thin Steel To SteelDrive pin for fixing thin steel to structural steel sections.

Part No Description Drive Pin Length Order QtySP12 Premium Steel Pin 13mm 100



Hardness 52 - 55HRC

Part No Description Washer Diameter Drive Pin Length Order QtySBR9 Decking Pin 14mm 20mm 100

* Suitable for use with Kingflor®, Bondek®, Condeck®

Drive Pins For Fixing Thin Steel To SteelDrive Pin designed for fixing thin steel to structural steel sections. This drive pin provides excellent clamping with a special 14mm diameter washer that interacts with a tapered section on the shank of the drive pin.

SpecificationsRaw Material Carbon SteelCorrosion Protection Zinc Electroplated (Min coating 7µm)Nominal Head Diameter 8.8mmNominal Shank Diameter 4.0mmShear Strength 1240N/mm2


Hardness 54 - 58HRC


LAU25

LZU30H




s

Part No Drive Pin Length Max Insulation Thickness

Order Qty

CR950P 50mm 25mm 200

Soft Washered Membrane FastenerSoft Washered Drive Pin designed for fastening insulation up to 25mm, also designed for fastening foils and membranes such as drainage sheeting to concrete. The soft washer prevents any damage to the foil or membrane.

SpecificationsRaw Material Carbon Steel (Plastic Washer)Corrosion Protection Zinc Electroplated (Min coating 7µm)Nominal Head Diameter 8.8mmNominal Shank Diameter 3.7mmShear Strength 1120N/mm2


Hardness 50 - 55HRC

Washer Diameter 35mm


Part No Description Order QtyRCA25F 25mm Angle Clip 100RCD16F 16mm Disc 100RCD22F 22mm Disc 100

Drive Pin AccessoriesDrive Pin accessories for use with Ramset’s standard LDU range of Standard Drive Pins for concrete, masonry and steel. The use of the discs provides maximum clamping loads while improving tool piston life. The use of the angle clip provides a fixing point for applications such as catenary wire.

SpecificationsRaw Material Low Carbon SteelCorrosion Protection Zinc Electroplated (Min coating 6µm)

RCD16F RCD22F RCA25F


Misc. Drive PinsPowder Actuated Systems

Pow

der

Actu

ated

Sys

tem

s

Collated Drive Pins to suit Hilti™, DX 351, DX 460, DX A40, DX A41 Magazine ToolsCollated Drive Pins designed for use with Hilti tools; DX460, DX351, DX-A40/41 fitted with a magazine.

Part No Head Diameter Length Max Fixture (Thickness to steel)

Max Fixture (Thickness to Concrete)

Order Qty

RHC22 8mm 22mm 10mm 1mm 100RHC27 8mm 27mm 14mm 3mm 100 RHC52 8mm 52mm 37mm 27mm 100RHC62 8mm 62mm 47mm 42mm 100RHC72 8mm 72mm 62mm 47mm 100



Hardness 52 - 55HRC

Part No Washer Diameter Drive Pin Length Order QtyLHS22 14mm 25mm 100

Sacrificial/Permanent Steel Formwork PinsDrive Pin specifically designed for use with Ramset’s DekMaster™ D230 tool. This Drive Pin is ideal for securing sacrificial steel formwork to heavy gauge structural steel.

SpecificationsRaw Material Carbon SteelCorrosion Protection Zinc Electroplated (Min coating 8µm)Nominal Head Diameter 14mmNominal Shank Diameter 4.5mmShear Strength 1425N/mm2


Hardness 54 - 58HRC


Drive Pins to suit Previous Ramset™ Tools - J20S, J20, 1/4” BarrelDrive Pins for use with previous Ramset™ direct acting powder actuated tools; J20, J20S fitted with a ¼” barrel.

Part No Head Diameter Length Order QtyHDB50 6.3mm 50mm 100HDB64 6.3mm 64mm 100HDB75 6.3mm 75mm 100HDB95 6.3mm 95mm 100



Hardness 52 - 55HRC


Power LoadsPowder Actuated Systems


s

SpecificationsCharge Type Single CartridgeCalibre 5.6 x 16mm

Powerloads to suit Previous Ramset™ Tools - J20S, J20, 1/4” BarrelPower Load Cartridge designed for use with Ramset’s JobMaster™ tool and previous Ramset™ direct acting powder actuated tools; J20, J20S.

Part No Calibre Colour Strength Order QtyPLCGR22S 5.6mm x 16mm Green Weak 100PLCYW22S 5.6mm x 16mm Yellow Medium 100PLCRD22S 5.6mm x 16mm Red Strong 100*PLCPU22S 5.6mm x 16mm Purple Very Strong 100

* Not suitable for use with JobMaster™

SpecificationsCharge Type 10 Shot StripCalibre 6.8 x 11mm

Strip Powerloads to suit Previous Ramset™ Strip Feed Tools & Hilti™ Strip Feed ToolsPower Load Strip designed for use with Ramset™ tools; FrameBoss™, FormMaster™, TyMaster™, FixMaster™ (TS60P), FrameMaster™ (TS750(P)), S75A, FrameFix™, Striker, Rocket. Also suitable for use with Hilti tools; DX460, DX351, DX-A40/41, DX36.

Part No Calibre Colour Strength Order QtyPLSGR22 6.8mm x 11mm Green Weak 100PLSYW22 6.8mm x 11mm Yellow Medium 100PLSRD22 6.8mm x 11mm Red Strong 100

Part No Calibre Colour Strength Order QtyPLDGR25 6.3mm x 10mm Green Weak 100PLDYW25 6.3mm x 10mm Yellow Medium 100PLDRD25L* 6.3mm x 12mm Red Strong 100

* Not suitable for use with Insulfast P370 tool

Powerloads to suit Previous Ramset™ Tools Disc Feed ToolsPower Load Disc designed for use with previous Ramset™ powder actuated tools including InsulFast™, D200 and D60.

SpecificationsCharge Type 10 Shot Disc

Calibre6.3 x 10mm6.3 x 12mm


Power LoadsPowder Actuated Systems

Pow

der

Actu

ated

Sys

tem

s

DekMaster™ Disc CartridgesPower Load Disc specifically designed for use with the Ramset™ DekMaster™ D230 tool.

Part No Calibre Colour Strength Order QtyPLDYW25X 6.3mm x 16mm Yellow Medium 100PLDBU25X 6.3mm x 16mm Blue Medium Strong 100 PLDRD25X 6.3mm x 16mm Red Strong 100

SpecificationsCharge Type 10 Shot StripCalibre 6.8 x 16mm



sNotes


NotesPo

wde

r Ac

tuat

ed S

yste

ms

Sales, Orders and Enquiries

Tel: 1300 780 063Fax: 1300 780 064Email: [email protected]: www.ramset.com.au

HEAD OFFICE296-298 Maroondah HighwayMooroolbark, Victoria 3138Tel: 03 9726 6222

STATE BRANCHESVICTORIA5/71 Victoria Crescent, Abbotsford 3067296-298 Maroondah Highway, Mooroolbark 3138

SOUTH AUSTRALIA115 Sir Donald Bradman Drive, Hilton 5033

NEW SOUTH WALES71 Carnarvon Street, Silverwater 2128563 Gardeners Road, Mascot 20203/8 Channel Road, Mayfield West 2034

ACT5/19 Tennant Street, Fyshwick 2609

QUEENSLAND281 Montague Road, West End 4101153 Ingham Road, Townsville 4810

WESTERN AUSTRALIA1/12 Colin Jamieson Drive, Welshpool 6106

ITW Construction Systems Australia Pty. Ltd. ABN 48 004 297 009 trading as Ramset™. ™Trademarks of Cetram Pty. Ltd. used under licence by Ramset™™FireFix is a trademark of Pirelli Cables. ®Hilti is a registered trademark of Hilti Corp. ®KingFlor is a registered trademark of Fielders Steel Roofing Pty. Ltd. ®CondeckHP is a registered trademark of Stramit Corporation Pty Ltd.

®Bondek is a registered trademark of BlueScope Steel Limited. ®Clipsal is a registered trademark of Clipsal Australia Pty. Ltd. © Copyright 2010 RAM/DF10/2010

In the interests of product improvement, Ramset™ reserves the right to alter product specifications as required. Information included in this Product Catalogue is correct at time of printing.

It is the responsibility of the user to ensure product selected is appropriate for its intended use. For further technical information go to www.ramset.com.au or contact Ramset™ on the numbers indicated.

Documents

Fixing Technology - Bradfastbradfast.com.au/wordpress/.../uploads/Ramset_Fixing... · Fixing to steel The resilience of steel provides a clamping effect to the fixing. This combined