Getting Mirc To Dcc Send Past Linksys Routers

Register or

search

Forums » Linksys » getting mirc to dcc

icon key

glossary:

Find Service

Reviews

Networking

FAQs+Info

Forums All forums City Forums All FAQs usenet Polls Mail-lists

Security

Our Tools

Buy

Join Club

For ISPs

Search

About us

Forums » Hardware By Brand » Linksys

By:

Linksys Forum FAQ FTP Modes and Ports Linksys Downloads

See: All, Unreplied Best topics over last 3 months

Author getting mirc to dcc : vote up?

Ultrakiller

Posts: 43 Joined 02-06-2002 Location: Boca Raton, FL

getting mirc to dcc OK i read all the guides here and put in linksys and mirc the same ports, etc but i still cant dcc files on mircI get "no firewall adress" message Im using the newest firm ware and i saw that in port forwarding it has application and in the guides i saw it didnt have themI enabled tcp and udp and im using 4990 - 5000 in both mirc and linksys I put my pc's lan ip address and still doesnt work can someone give me more ideas of what could be wrong?

Ultrakiller


in the forwarding i didnt put anything in customized applications and then i put mirc in it and it didnt workIM using dhcp so i put the port forwarding twice one to 192.168.1.100 and the other to 192.168.1.101 since my dhcp is setup to start @ 100 and i have two computers sharing the connection with the router Please help i need to dcc something quick :\

Support Our Soldiers mx6turbo89

I had this same problem too. You must 'disable' the router's DHCP function (bottom of page 51 of the Linksys manual) before using IP forwarding.

Pilgrim2

Joined 02-26-2002 Location: Seton Portage, BC DirecWay(satellite..

Yep! You have to disable the DCHP in the Linksys setup and the configure your TCP/IP on your PC for a static IP, e.g., 192.169.1.2, etc. You will also need the DNS numbers as well, which you can simply copy from the "Status" section of the Linksys online setup. Then it should work, unless you don't have your "mIRC/Options/Connect/Local Info" configured right. Jeff -- simul iustus et peccator

Ultrakiller


NOTE: this is in response to the post by Ultrakiller thanks but i cant connect to the internet with dhcp disabled :\ I did what you said pilgrim Disabled dhcp in linksys enabled use the following ip adress in tcp/ip properties and i used 192.168.1.2 and 192.168.1.100 (which was my ip when i had dhcp before),put the dns adresses that are on status in linksys and still doesnt go onlineCant open any page or irc It autoenables the subnet mask to 255.255.255.0 I also tried using gateway thats on the status too and it doesnt work Is there anything im missing to share the connections without dhcp? :\

Your Knight In Hopefully you have gotten your PC to be able to communicate with the internet through your Linky. The manual for the Linky should

broadband » Forums » Linksys » getting mirc to dcc

Page 1 of 6

Shining Armor KurosPaladin

Posts: 88 Joined 02-01-2002 Location: Waterford, MI

explain this. If you didn't get a manual, or lost it, you can download the manual from Linksys' web site in PDF format. For mIRC, here's what you need to do. This is all from memory, so some of the actual control names may be wrong.

l Set your PC to a static IP address within the subnet on your LAN (most likley 192.168.1.XXX).l Disable DHCP on the Linky's LAN side (you probably still need to use DHCP to get an IP address for the WAN side, though).l Forward 10 or so ports higher than 1024 from the WAN to your PC's IP address. (e.g. 5050

PC with mIRC, you must select different ranges for each. (I use the "tens" digit in the port range to determine the internal host. 192.168.0.5 gets 505X, 192.168.0.6 gets 506X, etc.).

l In port triggering, add a line with "mIRC" as the application name, 6660range. This one is tricky because IRC servers run on a wide range of ports, 6667 is the "standard" port, but I've seen them from 6660 to 7000. This allows the IRC server to "validate" you as who you say you are. Most servers will deny access if you do not have identd enabled.

l In mIRC select File/Options/Connect.

¡ Clear out the host name box, if there's anything there. ¡ Clear out the IP Address box, if there's anything there. ¡ Check "Host Name" (IP Address checkbox should grey out). ¡ Select "Server" for "Lookup Method"

l Somewhere in "Connect" (either it's level or below) is an option to enable IDENTD. You need to enable this.l Select DCC from Options tree and expand it (click on "+"). l Select Options. l Put the port range you forwarded from the Linky into the two text boxes for DCC Start and DCC End. (e.g. DCC Start would

be 5050, DCC End would be 5059, if you used the example ports above). 10 ports should be more than adequate.l Click "Ok" l Close mIRC. l Restart mIRC.

I've noticed in the past that changes made in the options of mIRC do not take effect until the next session, so that's why you have to quit and restart mIRC. I hope this helped! If not, let us know where your stuck at. -- Got balls? Play pinball! Black Knight 2000, Whirlwind, Twilight Zone, Roadshow, Earthshaker, Star Trek: TNG, and FunHouse.

Ultrakiller


NOTE: this is in response to the post by Ultrakiller I appreciate the help KurosPaladin i did that exactly the problem is i loose internet when i disable dhcp in the linksys options I dont know why it doesnt want to go online Ill read the manual to see if im missing something Thanks

Rawr pH1

Joined 12-31-2001 Location: Canada

Cogeco

said by Ultrakiller:

I appreciate the help KurosPaladin i did that exactly the problem is i loose internet when i disable dhcp in the linksys options I dont know why it doesnt want to go online Ill read the manual to see if im missing something Thanks

So leave it enabled and set static IPs


Page 2 of 6

Your Knight In Shining Armor KurosPaladin


NOTE: this is in response to the post by Ultrakiller I am assuming your ISP gives you a dynamic IP address, so try this out:

l Log onto the Linksys router and visit the SETUP tab (should be there by default).

¡ Check/select the option for obtaining an IP automatically. ¡ Select the LAN IP for your Linky (defaults to 192.168.1.1). ¡ Select the subnet mask of 255.255.255.0 ¡ Click APPLY ¡ Wait a few seconds before clicking "CONTINUE" (I've noticed the Linky takes a second to program itself, can't hurt to

let it do its thing).

l Select the DHCP tab

¡ Select "Disable DHCP server" ¡ Click APPLY ¡ Click "CONTINUE"

l On your PC, give it a static IP address of 192.168.1.5 (if you gave the Linky 192.168.1.1) I usually leave a gap between the

gateway and my workstations just in case I want to add a service in the lowerl Give the PC a subnet mask of 255.255.255.0 l Reboot PC

If this still doesn't work, then it is possible that you either have another device on the network squatting on one of the IP addresses you've assigned, or you have the subnets set up improperly. Just a basic review, 192.168.XXX.YYY is a private range of addresses not routeable on the public internet. If you have the router using 192.168.1.YYY, then (in most home environments) you'll want your PCs to use 192.168.1.YYY, as well. Only the fourth group of numbers should differ on your LAN for each device. Make certain you don't have the router in the 192.168.1.255 subnet and your PC in a different subnet (such as 192.168.0.255). You shouldn't assign '0' or '255' as the last part of an IP address, since these are broadcast addresses.-- Got balls? Play pinball! Black Knight 2000, Whirlwind, Twilight Zone, Roadshow, Earthshaker, Star Trek: TNG, and FunHouse.

Ultrakiller


NOTE: this is in response to the post by Ultrakiller what do you mean i shouldnt assing 255 or 0? where shouldnt i assign this? the subnet to my isp ends on 248 and the subnet configured in my linksys to my lan ends in 0 and i set the subnet in my pc to 0I have static ip for my isp but it still doesnt works



You should NOT have any device on your LAN using an IP address (not subnet) that ends in 0 or 255 (e.g. 192.168.1.0 or 192.168.1.255). Only use IP addresses that end between '1' and '254'. Your ISP's subnet is whatever they want it to be, and will be discovered by your Linky when it performs its DHCPDISCOVER. To help, try these settings: Your LAN subnet should be 255.255.255.0 Your Linky's LAN IP address should be 192.168.1.1 Your PC's IP address should be 192.168.1.5 Your PC's subnet should be 255.255.255.0 Your PC's DNS servers should be the ones that the Linky shows in its "Setup" or "Status" tab.Your PC's Default Gateway should be 192.168.1.1 You should not need WINS on your PC.


Page 3 of 6

Your PC's name (on DNS tab) can be whatever you want, but try to restrict it to "common" characters. (e.g. 0 Can you ping your router's LAN IP address of 192.168.1.1? Can you ping your router's WAN IP (shown in the "Status" tab of the Linky)? Can you ping www.dslreports.com? If you can ping 192.168.1.1, then you can get to the router. If you can ping www.dslreports.com, then you're getting there, and it may be a problem specific to mIRC. Let us know. -- Got balls? Play pinball! Black Knight 2000, Whirlwind, Twilight Zone, Roadshow, Earthshaker, Star Trek: TNG, and FunHouse.

Pilgrim2


NOTE: this is in response to the post by KurosPaladin Attachments:

That's a great instructional! And so he can see an actual setup on the Linksys side of things, I've included a screenshot of how I have mirc and ICQ setup in the "Advanced/Forwarding" section. As you said, the ports you add in "Forwarding" (for DCC send/receive files) must also be the same in the mIRC Options/DCC/Options section. Jeff --

Forwarding.gif

8219 bytesmirc_DCC.gif

17214 bytes


Page 4 of 6

simul iustus et peccator



Pilgrim, I'm curious how your identd is working. You have 113 forwarded to TWO internal IPs. I'm guessing the Linky is using one of those and sending it to that one. By putting it in the triggering range, you can specify which host it will go to, because it will go back to the host that triggered the outgoing port(s). Do you have identd running on one of those two hosts at all times (192.168.1.2 or 192.168.1.3)? Just curious. -- Got balls? Play pinball! Black Knight 2000, Whirlwind, Twilight Zone, Roadshow, Earthshaker, Star Trek: TNG, and FunHouse.

Pilgrim2


Well, it's like this: I'm more than ignorant about these things, hehe. All I know is that the setup I have now works great. The two hosts: 192.168.1.2 and 192.168.1.3 are, of course, my two PC's I have on my LAN. I have the "Ident server" checked in mIRC on both machines. I was told that I needed to replicate the settings for all computers that will be using the same application, e.g., mIRC. Since my wife uses the other computer and rarely if ever sends/receives files in mIRC, I didn't plug in different ports for the DCC item. But using Port 113 for both hasn't caused any problems. Without adding 113, it would take upwards of 1 minute to connect to an IRC server. With it added, connection is bascially instantaneous. Now, if I have failed to answer your question, please realize that it wasn't intentional. I'm just ignorant. Jeff -- simul iustus et peccator

Lanik Joined 06-25-2001 Location: San Jose,

CA Pacific Bell - SBC

Instead of forwarding IDENT I trigger it. That way it will work on all PCs that I have here. And so you guys know you can't forward IDENT to 2 systems at the same time. The same port can't be forwarded to 2 different systems. I think that is how it works.-- McLarenF1 -- Live fast, die without regrets.

Pilgrim2


Again, to unabashedly show my ignorance, are you saying that what I have now theoretically shouldn't work? I have had both PC's connected to the same IRC server and everything worked fine. We even sent/received files to each other using mIRC. But if this isn't what you were referring to, in my best Gilda Radner (Rosannanadana impression) NEVER MIND! Jeff -- simul iustus et peccator

Lanik Joined 06-25-2001 Location: San Jose,

CA Pacific Bell - SBC

said by Pilgrim2:

... are you saying that what I have now theoretically shouldn't work?

That is correct. Technically it shouldn't I don't see how the same ports can be forwarded to the 2 different systems at the same time. But it works, nothing short of amazing. -- McLarenF1 -- Live fast, die without regrets.


Page 5 of 6

Bill In Michigan Bill_MI

Joined 01-03-2001 Location: Royal Oak, MI EarthLink

NOTE: this is in response to the post by Pilgrim2 Pilgrim, 1 of those forwards is active, 1 is not. Last time I checked the first one is active. Forwarding to 2 machines is not possible with TCP as we know it today. Now... will it work? Very possible. There's absolutely no reason your .2 box cannot IDENT reply for the .3 box. The IRC server doesn't care. I use 1 box to answer ALL IDENT requests here. Why not satisfy your own curiosity? Enable the mIRC option to display IDENT replies on both machines. Which one gets all the requests? Keep in mind you usually get a request at IRC server connect time.

Pilgrim2


Bill, Hey, I'm learning as I go here! So, if I read you right, what you are saying and suggesting is that I can remove the mirc Port 113 entry for the #3 box and all should still work fine, eh?

Thanks for being patient with this old dog! Jeff -- simul iustus et peccator

Ultrakiller


NOTE: this is in response to the post by KurosPaladin

said by KurosPaladin:

Your PC's Default Gateway should be 192.168.1.1

Thank you paladin for helping me with my stupidity this was why it didnt work didnt know i had to put the linksys ip in gateway

Bill In Michigan Bill_MI

Joined 01-03-2001 Location: Royal Oak, MI EarthLink

NOTE: this is in response to the post by Pilgrim2 Jeff, IRC is not the easiest of concepts to get down - it has a legacy that makes no real sense to the new user. For instance, IDENT is a little check when you connect to an IRC server that evolved from UNIX systems so the person logged in a workstation can be identified. It's also used in some FTP and mail situations. It's virtually obsolete, now, but hangs on to this day though it makes little sense in most Windows systems. Also, it has no direct use for DCC files and chat connection. How old? I just turned 48.

Forums » Hardware By Brand » Linksys

22:05 eastern© 1999-2003 broadbandreports.com/dslreports.com.

Terms of Use - Privacy Policy. Use signifies your agreement. Another Satisfied Customer of Net Access Corp. - DSL,Hosting & Co -lo. www.nac.net - page compression ON

feedback


Page 6 of 6

Documents

Getting Mirc To Dcc Send Past Linksys Routers