High Common-Mode Voltage, Bidirectional Current Shunt Amplifier

Data Sheet AD8206

Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2005–2012 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com

FEATURES Ideal for current shunt applications High common-mode voltage range

−2 V to +65 V operating −25 V to +75 V survival

Gain = 20 Wide operating temperature range

−40°C to +125°C for Y grade and WY grade −40°C to +150°C for WH grade

Bidirectional operation Available in 8-lead SOIC Qualified for automotive applications

EXCELLENT AC AND DC PERFORMANCE 15 µV/°C offset drift 30 ppm/°C gain drift 80 dB CMRR dc to 20 kHz

APPLICATIONS High-side current sensing in

Motor controls Transmission controls Diesel-injection controls Engine management Suspension controls Vehicle dynamic controls DC-to-dc converters

FUNCTIONAL BLOCK DIAGRAM

0495

3-00

1

AD8206

8

1

4

2

3

7

5

6

+IN

–IN

NC

NC = NO CONNECTGND

V+

OUT

VREF1

VREF2

Figure 1.

GENERAL DESCRIPTION

The AD8206 is a single-supply difference amplifier for amplifying small differential voltages in the presence of large common-mode voltages. The operating input common-mode voltage range extends from −2 V to +65 V. The typical single-supply voltage is 5 V.

The AD8206 is offered in an 8-lead SOIC package. The Y grade and WY grade models are rated for operation from −40°C to +125°C. The WH grade is rated from −40°C to +150°C.

Excellent DC performance over temperature keeps errors in the measurement loop to a minimum. Offset drift is typically less than 15 µV/°C, and gain drift is typically below 30 ppm/°C.

The output offset can be adjusted from 0.08 V to 4.7 V with a 5 V supply by using the VREF1 and VREF2 pins. With VREF1 attached to the V+ pin, and VREF2 attached to the GND pin, the output is set at half scale. Attaching both pins to GND causes the output to be unipolar, starting near ground. Attaching both pins to V+ causes the output to be unipolar starting near V+. Other offsets can be obtained by applying an external voltage to the VREF1 and VREF2 pins.

AD8206 Data Sheet

Rev. B | Page 2 of 16

TABLE OF CONTENTS Features .............................................................................................. 1

Excellent AC and DC Performance ................................................ 1

Applications ....................................................................................... 1

Functional Block Diagram .............................................................. 1

General Description ......................................................................... 1

Revision History ............................................................................... 2

Specifications ..................................................................................... 3

Absolute Maximum Ratings ............................................................ 5

ESD Caution .................................................................................. 5

Pin Configuration and Function Descriptions ............................. 6

Typical Performance Characteristics ............................................. 7

Theory of Operation ........................................................................ 9

Output Offset Adjustment ............................................................. 10

Unidirectional Operation .......................................................... 10

Ground Referenced Output ...................................................... 10

V+ Referenced Output .............................................................. 10

Bidirectional Operation ............................................................. 10

External Referenced Output ..................................................... 11

Splitting the Supply .................................................................... 11

Splitting an External Reference ................................................ 11

Applications ..................................................................................... 12

High-Side Current Sense with a Low-Side Switch ................. 12

High-Side Current Sense with a High-Side Switch ............... 12

Outline Dimensions ....................................................................... 13

Ordering Guide .......................................................................... 13

Automotive Products ................................................................. 13

REVISION HISTORY

11/12—Rev. A to Rev. B Added WH Grade Models ................................................. Universal Change to Product Title, Features Section, and General Description Section .......................................................................... 1 Changes to Table 1 ............................................................................ 3 Added Y Grade and WY Grade Parameter, Table 2 and WH Grade Parameter, Table 2 ................................................................. 5 Changes to Theory of Operation Section ...................................... 9 Updated Outline Dimensions ....................................................... 13 Changes to Ordering Guide .......................................................... 13

5/10—Rev. 0 to Rev. A Removed Die Form ............................................................ Universal Changes to Features, General Description Sections ..................... 1 Changes to Output Resistance ......................................................... 3 Changes to Table 2 ............................................................................. 4 Changes to Theory of Operation Section....................................... 8 Changes to Ordering Guide .......................................................... 12 Added Automotive Products Section .......................................... 12

7/05—Revision 0: Initial Version

Data Sheet AD8206

Rev. B | Page 3 of 16

SPECIFICATIONS TA = operating temperature range, VS = 5 V, unless otherwise noted.

Table 1.

Parameter Test Conditions/Comments AD8206 SOIC

Unit Min Typ Max GAIN

Initial 20 V/V Accuracy VO ≥ 0.1 V dc, 25°C ±1 % Accuracy Over Temperature Specified temperature range ±1.2 % Gain vs. Temperature 30 ppm/°C

VOLTAGE OFFSET Offset Voltage (RTI) 25°C ±2 mV Over Temperature (RTI) Specified temperature range ±4.5 mV Offset Drift 15 µV/°C

INPUT Input Impedance

Differential 400 kΩ Common Mode 200 kΩ

Input Voltage Range Common mode, continuous −2 +65 V Differential1 250 mV Common-Mode Rejection 25°C, f = dc to 20 kHz2 76 86 dB Operating temperature range,

f = dc to 20 kHz2 76 80 dB

OUTPUT Output Voltage Range AD8206YRZ, RL = 25 kΩ 0.08 4.7 V AD8206WYRZ, RL = 25 kΩ 0.08 4.7 V AD8206WHRZ, RL = 25 kΩ 0.08 4.65 V Output Resistance 2 Ω

DYNAMIC RESPONSE Small Signal −3 dB Bandwidth 100 kHz Slew Rate 0.5 V/µs

NOISE 0.1 Hz to 10 Hz, RTI 20 µV p-p Spectral Density, 1 kHz, RTI 0.5 µV/√Hz

OFFSET ADJUSTMENT Ratiometric Accuracy3 Divider to supplies 0.497 0.503 V/V Accuracy, RTO Voltage applied to VREF1 and VREF2 in parallel ±2 mV/V Output Offset Adjustment Range AD8206YRZ, VS = 5 V 0.08 4.7 V AD8206WYRZ, VS = 5 V 0.08 4.7 V AD8206WHRZ, VS = 5 V 0.08 4.65 V VREF Input Voltage Range 0.0 VS V VREF Divider Resistor Values 24 32 40 kΩ

AD8206 Data Sheet

Rev. B | Page 4 of 16

Parameter Test Conditions/Comments AD8206 SOIC

Unit Min Typ Max POWER SUPPLY

Operating Range 4.5 5.5 V Quiescent Current Over Temperature AD8206YRZ, VO = 0.1 V dc 2 mA AD8206WYRZ, VO = 0.1 V dc 2 mA AD8206WHRZ, VO = 0.1 V dc 2.2 mA Power Supply Rejection Ratio 70 dB

OPERATING TEMPERATURE RANGE For Specified Performance AD8206YRZ −40 +125 °C AD8206WYRZ −40 +125 °C AD8206WHRZ −40 +150 °C

1 Input voltage range = ±125 mV with half-scale offset. 2 Source imbalance < 2 Ω. 3 The offset adjustment is ratiometric to the power supply when VREF1 and VREF2 are used as a divider between the supplies.

Data Sheet AD8206

Rev. B | Page 5 of 16

ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Rating Supply Voltage 12.5 V Continuous Input Voltage −25 V to +75 V Input Transient Survival −30 V to +80 V Differential Input Survival −25 V to 75 V Reverse Supply Voltage 0.3 V Operating Temperature Range

Y Grade and WY Grade −40°C to +125°C WH Grade −40°C to +150°C

Storage Temperature Range −65°C to +150°C Output Short-Circuit Duration Indefinite

Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

ESD CAUTION

AD8206 Data Sheet

Rev. B | Page 6 of 16

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

0495

3-00

2

Figure 2. Metallization Diagram

NC = NO CONNECT

AD8206TOP VIEW

(Not to Scale)

–IN 1

GND 2

VREF2 3

NC 4

+INVREF1V+OUT

8

7

6

5

0495

3-00

3

Figure 3. Pin Configuration

Table 3. Pin Function Descriptions Pin No. Mnemonic X Y 1 −IN −209 +486 2 GND −447 +34 3 VREF2 −432 −480 4 NC N/A N/A 5 OUT +444 −495 6 V+ +444 −227 7 VREF1 +456 +342 8 +IN +207 +486

Die size is 1245 µm by 1400 µm.

Die thickness is 13 mil.

Minimum passivation opening (minimum bond pad size) is 92 µm × 92 µm.

Passivation type is 8KA USG (Oxide) + 10KA Oxynitride.

Bond pad metal composition is 98.5% Al, 1% Si, and 0.5% Cu.

Backside potential is V+.

Data Sheet AD8206

Rev. B | Page 7 of 16

TYPICAL PERFORMANCE CHARACTERISTICS 500

–500

–400

–300

–200

–100

0

100

200

300

400

–40 –20 0 20 40 60 80 100 120 140

0495

3-03

6

TEMPERATURE (°C)

V OSI

(µV)

TYPICALIN SOIC

TYPICALDIE

Figure 4. Typical Offset Drift

120

110

100

90

80

70

60

50

40

30

20

10

010 100 1k 10k 100k 1M 10M

0495

3-00

4

FREQUENCY (Hz)

CM

R (d

B)

Figure 5. CMR vs. Frequency

12000

–12000

–10000

–8000

–6000

–4000

–2000

0

2000

4000

6000

8000

10000

–40 –20 0 20 40 60 80 100 120 140

0495

3-03

5

TEMPERATURE (°C)

GA

IN E

RR

OR

(ppm

) TYPICALIN SOIC

TYPICALDIE

Figure 6. Gain Drift

40

35

30

25

20

15

10

5

010 100 1k 10k 100k 1M

0495

3-00

7

FREQUENCY (Hz)

GA

IN (d

B)

Figure 7. Typical Small Signal Bandwidth (VOUT = 200 mV p-p)

0495

3-02

3

40µs/DIV

200mV/DIV

1V/DIV

Figure 8. Rise/Fall Time

0495

3-02

5

2µs/DIV

250mV/DIV

2V/DIV

Figure 9. Differential Overload Recovery (Falling)

AD8206 Data Sheet

Rev. B | Page 8 of 16

0495

3-02

42µs/DIV

250mV/DIV

2V/DIV

Figure 10. Differential Overload Recovery (Rising)

0495

3-02

2

40µs/DIV

2V/DIV

0.01%/DIV

Figure 11. Settling Time

0495

3-02

6

1µs/DIV

50V/DIV

50mV/DIV

Figure 12. Common-Mode Response

0.50

0.45

0.40

0.35

0.30

0.25

0.20

0.15

0.10

0.05

0–40 –20 0 20 40 60 80 100 120 140

0495

3-03

0

TEMPERATURE (°C)

MA

XIM

UM

OU

TPU

T SI

NK

CU

RR

ENT

(mA

)

Figure 13. Output Sink Current vs. Temperature

10

9

8

7

6

5

4

3

2

1

0–40 –20 0 20 40 60 80 100 120 140

0495

3-03

1

TEMPERATURE (°C)

MA

XIM

UM

OU

TPU

T SO

UR

CE

CU

RR

ENT

(mA

)

Figure 14. Output Source Current vs. Temperature

5.04.94.84.74.64.54.44.34.24.14.03.93.83.73.63.5

0 4.03.53.02.52.01.51.00.5

0495

3-03

4

OUTPUT SOURCE CURRENT (mA)

OU

TPU

T VO

LTA

GE

RA

NG

E (V

p-p

)

Figure 15. Output Voltage Range vs. Output Source Current

Data Sheet AD8206

Rev. B | Page 9 of 16

THEORY OF OPERATION The AD8206 is a single-supply difference amplifier that uses a unique architecture to accurately amplify small differential current shunt voltages in the presence of rapidly changing common-mode voltage. It is offered in an 8-lead SOIC package.

In typical applications, the AD8206 is used to measure current by amplifying the voltage across a current shunt placed across the inputs.

The gain of the AD8206 is 20 V/V, with an accuracy of 1.2%. This accuracy is guaranteed over the operating temperature range of −40°C to +125°C. Note, however, that the WH grade version of the AD8206 is specified for operation from −40°C to +150°C, with the same accuracy of 1.2%.

The AD8206 operates with a single supply from 4.5 V to 10 V (absolute maximum = 12.5 V). The supply current is less than 2 mA.

High accuracy trimming of the internal resistors allows the AD8206 to have a typical common-mode rejection ratio better than 80 dB from dc to 20 kHz. The minimum common-mode rejection ratio over the operating temperature is 76 dB.

The output offset can be adjusted from 0.08 V to 4.7 V (VS = 5 V) for unidirectional and bidirectional operation.

The AD8206 consists of two amplifiers (A1 and A2), a resistor network, a small voltage reference, and a bias circuit. See Figure 16 for a simplified schematic diagram (bias circuit not shown).

The set of input attenuators preceding A1 consist of RA, RB, and RC, which reduce the common-mode voltage to match the input voltage range of A1. The two attenuators form a balanced bridge network. When the bridge is balanced, the differential voltage created by a common-mode voltage is 0 V at the inputs of A1. The input attenuation ratio is 1/16.7. The combined series resistance of RA, RB, and RC is approximately 200 kΩ ± 20%.

By attenuating the voltages at Pin 1 and Pin 8, the A1 amplifier inputs are held within the power supply range, even if Pin 1 and Pin 8 exceed the supply or fall below common (ground). A reference voltage of 250 mV biases the attenuator above ground. This allows the amplifier to operate in the presence of negative common-mode voltages.

The input network also attenuates normal (differential) mode voltages. A1 amplifies the attenuated signal by 26. The input and output of this amplifier are differential to maximize the ac common-mode rejection.

A2 converts the differential voltage from A1 into a single-ended signal and provides further amplification. The gain of this second stage is 12.86.

The reference inputs, VREF1 and VREF2, are tied through resistors to the positive input of A2, which allows the output offset to be adjusted anywhere in the output operating range. The gain is 1 V/V from the reference pins to the output when the reference pins are used in parallel. The gain is 0.5 V/V when they are used to divide the supply.

The ratios of Resistors RA, RB, RC, RD, and RF are trimmed to a high level of precision to allow the common-mode rejection ratio to exceed 80 dB. This is accomplished by laser trimming the resistor ratio matching to better than 0.01%.

The total gain of 20 is made up of the input attenuation of 1/16.7 multiplied by the first stage gain of 26 and the second stage gain of 12.86.

The output stage is a Class A with a PNP pull-up transistor and a 300 µA current sink pull-down.

0495

3-01

3

AD8206

+IN–IN

250mV

GND

A1

A2

RA RA

RB RB RF RF RD RD

RE RF

RC RCVOUT

RREF

RREF

VREF1

VREF2 Figure 16. Simplified Schematic

AD8206 Data Sheet

Rev. B | Page 10 of 16

OUTPUT OFFSET ADJUSTMENT The output of the AD8206 can be adjusted for unidirectional or bidirectional operation.

UNIDIRECTIONAL OPERATION Unidirectional operation allows the AD8206 to measure currents through a resistive shunt in one direction. The basic modes for unidirectional operation are ground referenced output mode and V+ referenced output mode.

For unidirectional operation, the output can be set at the negative rail (near ground) or at the positive rail (near V+) when the differential input is 0 V. The output moves to the opposite rail when a correct polarity differential input voltage is applied. In this case, full scale is approximately 250 mV. The required polarity of the differential input depends on the output voltage setting. If the output is set at the positive rail, the input polarity needs to be negative to move the output down. If the output is set at ground, the polarity is positive to move the output up.

GROUND REFERENCED OUTPUT When using the AD8206 in this mode, both referenced inputs are tied to ground, which causes the output to sit at the negative rail when there are zero differential volts at the input (see Figure 17).

0495

3-01

4

AD8206

+IN

–IN

NC

NC = NO CONNECT

GND

V+

OUT

VREF1

VREF2

Figure 17. Ground Referenced Output

Table 4. V+ = 5 V VIN (Referred to −IN) VO 0 V 0.08 V 250 mV 4.7 V

V+ REFERENCED OUTPUT This mode is set when both reference pins are tied to the positive supply. It is typically used when the diagnostic scheme requires detection of the amplifier and the wiring before power is applied to the load (see Figure 18).

0495

3-01

5

AD8206

+IN

–IN

NC

NC = NO CONNECT

GND

V+

OUT

VREF1

VREF2

Figure 18. V+ Referenced Output

Table 5. V+ = 5 V VIN (Referred to −IN) VO 0 V 4.7 V −250 mV 0.08 V

BIDIRECTIONAL OPERATION Bidirectional operation allows the AD8206 to measure currents through a resistive shunt in two directions.

In this case, the output is set anywhere within the output range. Typically, it is set at half-scale for equal range in both directions. In some cases, however, it is set at a voltage other than half-scale when the bidirectional current is nonsymmetrical.

Table 6. V+ = 5 V, VO = 2.5 V with VIN = 0 V VIN (Referred to −IN) VO +100 mV 4.5 V −100 mV 0.5 V

Adjusting the output is accomplished by applying voltage(s) to the referenced inputs.

VREF1 and VREF2 are tied to internal resistors that connect to an internal offset node. There is no operational difference between the pins.

Data Sheet AD8206

Rev. B | Page 11 of 16

EXTERNAL REFERENCED OUTPUT Tying both pins together and to a reference produces an output equal to the reference voltage when there is no differential input (see Figure 19). The output moves down from the reference voltage when the input is negative, relative to the −IN pin and up when the input is positive, relative to the −IN pin.

0495

3-01

6

AD8206

+IN

–IN

NC

NC = NO CONNECT

GND

V+

OUT

VREF1

VREF2

2.5V VOLTAGEREFERENCE

Figure 19. External Referenced Output

SPLITTING THE SUPPLY By tying one reference pin to V+ and the other to the ground pin, the output is set at half of the supply when there is no differential input (see Figure 20). The benefit is that no external reference is required to offset the output for bidirectional current measurement. This creates a midscale offset that is ratiometric to the supply, which means that if the supply increases or decreases, the output remains at half the supply. For example, if the supply is 5.0 V, the output is at half scale or 2.5 V. If the supply increases by 10% (to 5.5 V), the output goes to 2.75 V.

0495

3-01

7

AD8206

+IN

–IN

NC

NC = NO CONNECT

GND

V+

OUT

VREF1

VREF2

Figure 20. Split Supply

SPLITTING AN EXTERNAL REFERENCE In this case, an external reference is divided by 2 with an accuracy of approximately 0.5% by connecting one VREF pin to ground and the other VREF pin to the reference (see Figure 21).

0495

3-01

8

AD8206

+IN

–IN

NC

NC = NO CONNECT

GND

V+

OUT

VREF1

VREF2

5V VOLTAGEREFERENCE

Figure 21. Split External Reference

AD8206 Data Sheet

Rev. B | Page 12 of 16

APPLICATIONS A typical application for the AD8206 is high-side measurement of a current through a solenoid for PWM control of the solenoid opening. Typical applications include hydraulic transmission control and diesel injection control.

Two typical circuit configurations are used for this type of application.

HIGH-SIDE CURRENT SENSE WITH A LOW-SIDE SWITCH In this case, the PWM control switch is ground referenced. An inductive load (solenoid) is tied to a power supply. A resistive shunt is placed between the switch and the load (see Figure 22). An advantage of placing the shunt on the high side is that the entire current, including the recirculation current, can be measured since the shunt remains in the loop when the switch is off. In addition, diagnostics can be enhanced because shorts to ground can be detected with the shunt on the high side.

In this circuit configuration, when the switch is closed, the common-mode voltage moves down to near the negative rail. When the switch is opened, the voltage reversal across the inductive load causes the common-mode voltage to be held one diode drop above the battery by the clamp diode.

0495

3-01

9

+IN VREF1 +VS OUT

–IN GND VREF2 NC

INDUCTIVELOAD

AD8206

CLAMPDIODE

42VBATTERY

SHUNT

SWITCH

NC = NO CONNECT

5V

Figure 22. Low-Side Switch

HIGH-SIDE CURRENT SENSE WITH A HIGH-SIDE SWITCH This configuration minimizes the possibility of unexpected solenoid activation and excessive corrosion (see Figure 23). In this case, both the switch and the shunt are on the high side. When the switch is off, this removes the battery from the load, which prevents damage from potential shorts to ground, while still allowing the recirculating current to be measured and providing for diagnostics. Removing the power supply from the load for the majority of the time minimizes the corrosive effects that could be caused by the differential voltage between the load and ground.

When using a high-side switch, the battery voltage is connected to the load when the switch is closed, causing the common-mode voltage to increase to the battery voltage. In this case, when the switch is opened, the voltage reversal across the inductive load causes the common-mode voltage to be held one diode drop below ground by the clamp diode.

0495

3-02

0

+IN VREF1 +VS OUT

–IN GND VREF2 NC

INDUCTIVELOAD

AD8206

CLAMPDIODE

42VBATTERY

SHUNT

SWITCH

NC = NO CONNECT

5V

Figure 23. High-Side Switch

Another typical application for the AD8206 is as part of the control loop in H-bridge motor control. In this case, the AD8206 is placed in the middle of the H-bridge (see Figure 24) so that it can accurately measure current in both directions by using the shunt available at the motor. This is a better solution than a ground referenced op amp because ground is not typi-cally a stable reference voltage in this type of application. This instability in the ground reference causes the measurements that could be made with a simple ground referenced op amp to be inaccurate.

The AD8206 measures current in both directions as the H-bridge switches and the motor changes direction. The output of the AD8206 is configured in an external reference bidirectional mode, see the Output Offset Adjustment section.

0495

3-02

1

+IN VREF1 +VS OUT

–IN GND VREF2 NC

AD8206SHUNT

5V

2.5V

5V

CONTROLLER

NC = NO CONNECT

MOTOR

Figure 24. Motor Control Application

Data Sheet AD8206

Rev. B | Page 13 of 16

OUTLINE DIMENSIONS

CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FORREFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.

COMPLIANT TO JEDEC STANDARDS MS-012-AA

0124

07-A

0.25 (0.0098)0.17 (0.0067)

1.27 (0.0500)0.40 (0.0157)

0.50 (0.0196)0.25 (0.0099) 45°

8°0°

1.75 (0.0688)1.35 (0.0532)

SEATINGPLANE

0.25 (0.0098)0.10 (0.0040)

41

8 5

5.00 (0.1968)4.80 (0.1890)

4.00 (0.1574)3.80 (0.1497)

1.27 (0.0500)BSC

6.20 (0.2441)5.80 (0.2284)

0.51 (0.0201)0.31 (0.0122)

COPLANARITY0.10

Figure 25. 8-Lead Standard Small Outline Package [SOIC_N]

Narrow Body (R-8) Dimensions shown in millimeters and (inches)

ORDERING GUIDE Model1, 2 Temperature Range Package Description Package Option AD8206YRZ −40°C to +125°C 8-Lead SOIC_N R-8 AD8206YRZ-REEL −40°C to +125°C 8-Lead SOIC_N, 13” Tape and Reel R-8 AD8206YRZ-REEL7 −40°C to +125°C 8-Lead SOIC_N, 7” Tape and Reel R-8 AD8206WYRZ −40°C to +125°C 8-Lead SOIC_N R-8 AD8206WYRZ-R7 −40°C to +125°C 8-Lead SOIC_N, 7” Tape and Reel R-8 AD8206WYRZ-RL −40°C to +125°C 8-Lead SOIC_N, 13” Tape and Reel R-8 AD8206WHRZ −40°C to +150°C 8-Lead SOIC_N R-8 AD8206WHRZ-RL −40°C to +150°C 8-Lead SOIC_N, 13” Tape and Reel R-8 1 Z = RoHS Compliant Part. 2 W = Qualified for Automotive Applications.

AUTOMOTIVE PRODUCTS The AD8206W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models.

AD8206 Data Sheet

Rev. B | Page 14 of 16

NOTES

Data Sheet AD8206

Rev. B | Page 15 of 16

NOTES

AD8206 Data Sheet

Rev. B | Page 16 of 16

NOTES

©2005–2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04953–0–12/12(B)