168
Builders Hardware Catalog 4Plus © McKINNEY Products Company 2006, 2007

Hinge Catalog

Embed Size (px)

DESCRIPTION

VISAGRAS

Citation preview

Page 1: Hinge Catalog

Builders Hardware Catalog 4Plus

© McKINNEY Products Company 2006, 2007

Page 2: Hinge Catalog

McKINNEY Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 - 23Hinge Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Knuckle Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Hinge Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 - 14Reference Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 - 17Hand of Doors and Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Hinge Swaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Screws and Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 21Finishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 - 23

Full Mortise Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 - 39Full Mortise Bearing Hinges - Five Knuckle Heavy Weight StormPro® Series . . . . . . . . . . . . . . . . . . .24Full Mortise Plain Bearing Hinges - Two Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . .25Full Mortise Bearing Hinges - Two Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .26Full Mortise Bearing Hinges - Two Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Full Mortise Plain Bearing Hinges - Three Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . .28Full Mortise Bearing Hinges - Three Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . .29Full Mortise Bearing Hinges - Three Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .30Full Mortise Institutional Hinges - Three Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . .31Swing Clear Full Mortise Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . .32Full Mortise Plain Bearing Hinges - Five Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . .33Full Mortise Bearing Hinges - Five Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .34Wide Throw Full Mortise Bearing Hinges - Five Knuckle Standard Weight Series . . . . . . . . . . . . . . .35Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . . . .36Wide Throw Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . .37Swing Clear Full Mortise Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . .38Swing Clear Full Mortise Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . . .39

Pivots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41Standard Duty Center Hung Jamb Mount Pivot Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Full Mortise Anchor Hinge Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 - 48

Half Mortise Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 - 55Half Mortise Plain Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . . . . . . .49Half Mortise Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . . . . . . . . . . . .50Half Mortise Bearing Hinges - Three Knuckle Standard Weight Series (Reversible) . . . . . . . . . . . . .51Half Mortise Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . . . . . . . . . . . .52Half Mortise Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . . . . . . . . . . . . .53Swing Clear Half Mortise Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . .54Swing Clear Half Mortise Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . .55

Half Surface Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 - 63Half Surface Bearing Hinges - Three Knuckle Standard Weight Series (Reversible) . . . . . . . . . . . . .57Half Surface Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . . . . . . . . . . . . .58Half Surface Plain Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . . . . . . .59Half Surface Bearing Hinges - Five Knuckle Standard Weight Series (Reversible) . . . . . . . . . . . . . . .60Half Surface Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . . . . . . . . . . . . .61Swing Clear Half Surface Bearing Hinges - Three Knuckle Heavy Weight Series (Reversible) . . . . .62Swing Clear Half Surface Bearing Hinges - Five Knuckle Heavy Weight Series (Reversible) . . . . . .63

Full Surface Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 - 70Full Surface Bearing Hinges - Three Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .65Full Surface Bearing Hinges - Five Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . . . .66Full Surface Bearing Hinges - Three Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . .67Full Surface Bearing Hinges - Five Knuckle Standard Weight Series . . . . . . . . . . . . . . . . . . . . . . . . . .68Full Surface Swing Clear Bearing Hinges - Three Knuckle Heavy Weight Series . . . . . . . . . . . . . . . .69Full Surface Swing Clear Bearing Hinges - Five Knuckle Heavy Weight Series . . . . . . . . . . . . . . . . .70

Table ofContents Page#

April2003

Page 3: Hinge Catalog

McKINNEY Hinge Catalog

1 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Spring Hinges & Pivots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 - 84Full Mortise Single Acting Standard Weight Spring Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71Full Mortise Single Acting Standard Weight Spring Hinge Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72Half Surface Single Acting Standard Weight Spring Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73Heavy Duty Double Acting Spring Butt Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74Full Mortise Single Acting Ajustable Spring Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75Heavy Duty Adjustable Tension Simplex Half Surface Double Acting Door Spring . . . . . . . . . . . . . .76Simplex Full Mortise Double Acting Spring Butt Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 - 79Simplex Double Acting Clamp Flange Spring Butt Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80Simplex Half Surface Double Acting Spring Butt Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81Ajax Double Acting Horizontal Spring Pivot Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82Sagless Double Acting Gate Spring Pivot Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83Lightweight Double Acting Gravity Pivot Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

Miscellaneous Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 - 88Hinge Back Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85Combination Strike and Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86Emergency Door Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87Double Lipped Strike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

Specialty Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89- 99Electrolynx Hinge (QC Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89Concealed Circuit Electric Hinge (CC Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90Serviceable & Accessible Hinges (SER & ACC Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91Magnetic Monitoring Hinge (MM Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92Junction Box for Electric Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93Pocket Pivot Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94Standard Weight Loose Pin Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95Full Mortise Five Knuckle Plain Bearing Light Weight Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96Olive Knuckle Full Mortise Standard Weight Bearing Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97Raised Barrel Full Mortise Standard and Heavy Weight Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98Slip In Full Mortise Type I and Type II Standard Weight Bearing Hinges . . . . . . . . . . . . . . . . . . . . . .99Full Mortise Interim Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100

Aluminum Continuous Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 - 116Full Mortise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107, 108, 111, 112, 115Full Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110, 114Half Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113Aluminum Continuous Hinge Clearance Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116

Stainless Continuous Hinges and Edge Guards . . . . . . . . . . . . . . . . . . .117 - 156Full Mortise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 -143Half Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126, 147Swing Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 - 137Full Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124, 125, 130, 134, 141, 146300 Series Edge Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148-151Stainless and Steel Continuous Hinge Clearance Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122

Steel Continuous Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 - 147Full Mortise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144Half Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147Full Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145, 146

Cross Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iNumerical Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Inside Back Cover

DISCONTINUED

DISCONTINUED

Page 4: Hinge Catalog

McKINNEY Hinge Catalog

2May

2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY,Your Source For Hinges

McKINNEY Products Companyprovides the non-residentialconstruction industry with a full rangeof commercial door hinges for everyneed. The information in this catalogwill assist you in choosing the hingesthat fully satisfy your design andengineering requirements.Quality And Innovation For MoreThan 100 Years

McKINNEY Products Companyhas been a leader in the design andmanufacture of quality builder’shardware since 1865. McKINNEY is asubsidiary of ASSA ABLOY. TheASSA ABLOY Group is the world'sleading manufacturer and supplier oflocking solutions, dedicated tosatisfying end-user needs for security,safety and convenience.

McKINNEYproduces a fullline of commercialdoor hinges in avariety of finishes, bearingsand functions for all interior orexterior applications. AmongMcKINNEY’s many innovations wasthe oil impregnated bearing whichgreatly improved the performance ofbearing hinges. To meet today’s needfor greater security applications,McKINNEY developed a variety ofelectric hinges used in remote doormonitoring and access control systems.

Quality,performance

and the abilityto meet critical

construction deadlineshave made McKINNEY

hinges a first choice forconstruction projects worldwide.

Hinge SolutionsFor Every Design Need

McKINNEY hinges and other doorhanging hardware provide solutions forthe most highly specialized functionsas well as decorative requirements.The broad line and exceptionalquality ensure getting exactly theright product for your new or retrofitconstruction projects.

“McKINNEY iscomprised of a worldclass team of highlyskilled people focusedon exceeding customerneeds throughinnovation andflexibility in themanufacture ofarchitectural buildingproducts.”

Page 5: Hinge Catalog

McKINNEYHingeCatalogHingeTypes

3 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY offers the broadest rangeof full mortise hinges in a variety ofmetals, finishes, sizes, and weights tomeet all your load bearing and securityapplications. They include two, three,and five knuckle styles, swing clearhinges, wide throw hinges, anchorhinges, electric hinges, institutionalhinges, and pivots.

McKinney hinges conform toGovernment standards CS9-65 andSDI as well as the following standardsapproved by the Builders hardwareManufacturers / American NationalStandards Institute:ANSI/BHMA Standard 156.1 -The American National Standard forButts and Hinges

Available in a choice of metals, gauges,and sizes for a wide range of doorthicknesses. You may specify plainbearing, standard weight bearing, orheavy weight bearing models. Regularand swing clear applications. Twoknuckle, three knuckle, as well as fiveknuckle styles are available.

Choose from regular and swing clearmodels for heavy weight bearing orstandard weight bearing applications ina choice of metals, gauges, and sizes.Two knuckle, three knuckle, and fiveknuckle styles are available.

Heavy weight bearing, standard weightbearing, and plain bearing hinges in arange of metals, gauges, and sizes.Regular and swing clear applications.Two knuckle, three knuckle, and fiveknuckle styles

A full range of spring hinges areavailable for all types of door sizes,weights, and applications. Included arefull mortise single acting hinges, singleacting reverse spring hinges, full mortisedouble acting hinges, and half surfacedouble acting hinges, plus our heavy dutyspring butt hinge that permits doors toopen 90˚ in either direction. In addition,McKINNEY produces a variety of hingesfor special applications including anchorhinges, wide throw hinges, swing clearhinges, and pocket hinges.

McKINNEY self-aligning continuoushinges extend the full height of thedoor. These hinges bond the door andframe into an integrated unit andpresent a streamlined, no-gap surface,affording privacy, safety, andoutstanding performance. The highload capacity of these hinges makesthem ideal for use in high-frequencyareas where hinges are subject to abuse.The hinge design affords resistance tovandalism. McKINNEY continuousgeared hinges are warranted for thelife of the building. UL listed in boththe USA and Canada up to 3 hour(A label) application. These hingesare available in aluminum, stainlessand steel.

McKINNEY produces an assortment ofelectrical security hinges for a widevariety of control functions. Includedare full mortise bearing hinges witheither concealed circuitry or concealedswitch. In addition, a unique, field-replaceable magnet monitoring hinge,featuring a magnetic reed concealedswitch, is available. McKINNEY alsoproduces full mortise institutionalhinges for maximum security installations,and our full mortise single acting springhinge is available with a TamperResistant Screw (TRS Option) whichis screwed into the tension ratchet afterproper tension has been set.

McKINNEY provides a standard dutycenter hung jamb mount pivot set.

Additionally, we provide emergencydoor stops, strikes, and stainless steeledge guards.

The most up to date Templatesare available on our website @www.mckinneyhinge.com

McKINNEY offers the broadest rangeof full mortise hinges in a variety ofmetals, finishes, sizes, and weights tomeet all your load bearing and securityapplications. They include two, three,and five knuckle styles, swing clearhinges, wide throw hinges, anchorhinges, electric hinges, institutionalhinges, and pivots.

Full Mortise Hinges Half Mortise Hinges Continuous Hinges

Half Surface Hinges

Spring and Specialty HingesSecurity Hinges Misc.

Full Surface Hinges

ANSI/BHMA Standard 156.7 -The American National Standard forTemplate Hinge DimensionsANSI/BHMA Standard 156.17 -The American National Standard forSelf-Closing Hinges & PivotsANSI/BHMA Standard 156.18 -The American National Standard forMaterial and Finishes

Page 6: Hinge Catalog

McKINNEYHingeCatalogBearings

4May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

This is the designation fornon-bearing hinges. Knuckles aremachined with bearing-like surfacesto move against one another. These arenot recommended for high frequencydoors or doors with closing devices.These hinges are not approved for usein labeled openings. An anti-frictioncomponent is provided on allMcKINNEY three knuckleand Moderne (two knuckle) plainbearing hinges.

Ball bearings are available on all fiveknuckle bearing hinges 6" and over inheight as a standard. For other sizesthey are furnished as an option bywritten request.

One piece, non-ferrous, and self-lubricating bearings ensure evenlonger-lasting wear and resistance toclogging, corrosion, and hinge failure.This feature is standard and supplied onall five knuckle bearing hinges.

Concealed, anti-friction type bearingsare available on all five knucklebearing hinges, which provide long-lasting wear and consistency of hingebarrel design.

Note: All three and two knuckle bearing hingesare provided with concealed, anti-friction typebearings (designated TA).

Standard gauge McKINNEY threeknuckle and five knuckle bearinghinges (.123 - .160) are suppliedwith two bearings. These hinges areintended for use on doors subjectedto average traffic in residential andlight commercial construction.Four bearings can be specified(T4A2714/T4A2314) on somefive knuckle hinges.

Heavy gauge McKINNEY hinges(.180 - .203) are regularly furnishedwith four bearings. 8" five knucklehinges supplied with six bearings.These hinges are intended for use onheavy doors and high frequency doorsfor all types of construction.

Note: One bearing carries the vertical load ontwo bearing hinges. On four bearing hinges,two bearings carry the load.

Door weight, height, width,thickness and frequency of operationare all factors in determining theproper hinge. Four bearing hingesshould be specified whenever thereis any question.

McKINNEY steel or stainless steelbased Bearing Hinges are approved foruse on Labeled Applications basedupon Table 1 Reference NFPA-80Table 2-8.1.1 1995 Builders hardware.See catalog page 17 for additionalinformation.

Plain Bearing

Ball Bearing (TB)Oil Impregnated Bearing (TA)

Number of Bearings (Five Knuckle Only)

Page 7: Hinge Catalog

McKINNEYHingeCatalogKnuckle Features

5 March

2008

©McK

INNEYProductsCom

pany2006,2007,2008

1-800-346-7707 • www.mckinneyhinge.com

This model offers the most security ina standard hinge. The bearing hingeshave a concealed stainless steeloil-impregnated bearing. Also, ananti-friction bushing in the door leafprovides additional protection againstvertical and lateral wear.

•Plainbearinghingeshaveananti-frictioncomponent insertedbetween the twoknuckles

•TheModerne twoknucklehinge isavailable in stainless steel

•Standardandheavyweight•Pins inall bearinghinges arestainless steel

•Pins inplainbearinghinges are steelStainless steel pins are available.

•Standardhinges arepackedwithallmachinebyallwood screws

•Bydesign, pins arenon-rising,non-removable and tamperprotectedbya flush,non-removable capat theendof thebarrel.Adoor cannotberemovedwhen in theclosedposition,thus affordingmaximumsecurity.Intermediatehinges canbeorderedoppositehandand installedupsidedown, to inhibit removal of thedoor inanopenposition

•Availablenon-removabledoor (NRD)hingeshaveadowel in thebarrel.OneNRDhingecanbeorderedper set

•Twoknucklehinges arehanded•Templatehinges aremade toconformtoU.S.Government standards*

Bearing hinges have concealed verticaland lateral thrust twin anti-frictiontype bearings at both joints.

•Plainbearinghingeshaveananti-frictionTbushingatboth joints

•Pin stems inall non-ferrousbearinghinges are stainless steel

•Pins inall ferroushinges are steel•Pins inall hinges arenon-rising type•Standardhinges arepackedwithallmachinebyallwood screws

•Hinges are reversible for rightor lefthandexcept anchorhinges andcertainelectrichinges

•Templatehinges aremade toconformtoU.S.Government standards*

Bearing hinges are furnished witheither an oil-impregnated bearing(TA*) or ball bearing (TB). (TA isstandard unless TB is specified.)Concealed bearings (TCA) areavailable.

•Pin stems inall non-ferrousbearinghinges are stainless steel

•Pins inall ferroushinges are steel•Pins inall hinges arenon-rising type•Pincaps aremadeof the samematerialas thehinge

•Templatehinges aremade toconformtoU.S.Government standards*

* Refer toourwebsite atwww.mckinneyhinge.comfor additionalinformation regardingMcKinneybearings.

Three Knuckle Five KnuckleModerne Two Knuckle

A stud attached to the face of one leafrotates into a cavity in the opposite leafwhen the door is closed. This optioninterlocks the two leaves together,preventing the removal of the dooreven if the pin is removed.

SSF - Safety Stud Feature

*Template hinges are made in sizes, gauges,and with screw holes located to conform toANSI/BHMA A156.7 and U.S.Government standards CS9-65 and SDI.Templates are available on request.

NOTE:Dimensions and weights indicated throughoutthis catalog are in US/SI units; metricequivalents in millimeters and kilograms areshown in parenthesis.

A 7/16" diameter stud projects from theback of each leaf which slips into ahole in the hinge reinforcing plates inboth the door and the frame. Thisprevents the hinge from being removedeven if the screws have been shearedoff. This option is available on theHTA786 steel and HTA386 stainlessprison hinge only.

PSF - Prison Safety Feature

Page 8: Hinge Catalog

McKINNEYHingeCatalogTips

6January2004

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Hospital tips which feature a one-piecenon-removable pin with tapered tips.To order this option prefix our hingenumber by “H”. The hospital tipfeature by design makes the pinvirtually non-removable.

Hospital Tips

Button Tips and plugs are standard onMcKINNEY five knuckle hinges andcan be furnished on three knucklehinges as an option. These tips can bespecified on three knuckle hinges byadding the suffix “E.T.” (exposed tip).

Flush pins and plugs are furnished onour two and three knuckle hinges.

Ball Tips, made of solid brass, areavailable on three and five knucklehinges for a more decorative hingeappearance. To order this option addthe suffix “BT” to the hinge number.

Ball Tips

Standard Tips

Steeple Tips, made of solid brass, areavailable on three and five knucklehinges for a more decorative hingeappearance. To order this hinge option,add the suffix “ST” to the hingenumber.

Steeple Tips

Page 9: Hinge Catalog

McKINNEYHingeCatalogPins

7 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Non-Removable Pins

A set screw is driven into the barrel ofthe hinge that is inaccessible when thedoor is in the closed position. To order,add the suffix “NRP” to the hingenumber.

NRP

Two knuckle hinges are available witha non-removable pin which features adowel which is force fitted into thejamb leaf. When the door is hung, thepin is completely concealed andimpossible to remove. One doweledhinge is usually furnished per set ofthree. To order, add the suffix “NRD”to the hinge number.

NRD

Plain Bearing pins are furnished in steeland can be ordered with stainless steelpins as an option. To order this option,add the suffix “SSP” to the hingenumber. Pins on bearing hinges arefurnished in stainless steel.

Two Knuckle

Pin stems in all non-ferrous bearinghinges are stainless steel. Pins in allferrous hinges are steel.

Three Knuckle

Pins on all non-ferrous bearing hingesare stainless steel with the button tipsmanufactured of the same material asthe hinge leaves.

Pins on all ferrous hinges are steel.These hinges are available withoptional brass pins or stainless steelpins. To order these options, add thesuffix “BR” (brass) or “SSP” (stainless).

Five Knuckle

Pins, by design, are non-rising, non-removable and tamper protected by a flush,non-removable cap at the end of the barrel.

Page 10: Hinge Catalog

McKINNEYHingeCatalogHingeSelectionCommonFlushDoor/Wall/FrameApplication

8April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

This section will seek to addressdifferent variations of door, frameand wall conditions which you mightencounter in hanging the door andthe product solutions offered byMcKINNEY.

Included are some of the morecommon conditions and some of thenot-so-common conditions. The focushere will be on the type of hinge to usewithin a given door/frame/wallcondition. The following examples are

not intended to cover every possiblesituation in which a particular typehinge might be used, but only arepresentative sampling. Consult thefactory for any unusual installationrequirements not shown here.

The most common application is aflush door/frame/wall condition using ahollow metal frame with a standardhollow metal or wood door which isflush or 1⁄16" inset from the face of theframe, with a wall which is either flush(or inset from the face of the frame.Recommended to hang door for 180˚swing: Full Mortise Hinge. The samehinge could be used with a wood oraluminum frame provided thedoor/frame/wall conditions are flush.

Note: A fire labeled wood door requiressufficient hinge reinforcement to use thistype hinge.

Full Mortise Hinge

Furnished as 1⁄4" radius unless specifiedotherwise. 5⁄32" may be specified on fullmortise hinges 41⁄2" or larger. Specifyoption “RC”.

Round Corner Option

MCK TA2714

MCK RCT2714

APPLICATION

Page 11: Hinge Catalog

McKINNEYHingeCatalogHingeSelectionUncommonFlushDoor/Wall/FrameApplications

9 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

A hollow metal or wood door withchannel iron frame. Recommended tohang door for 180˚ swing:Half Mortise Hinge.

Half Mortise Hinge

MCK TA2771APPLICATION

MCK TA2772APPLICATION

MCK TA2774APPLICATION

A fire labeled wood door (withoutsufficient hinge reinforcement) or akalamein (metal-clad wood door) withchannel iron frame. Recommended tohang door for 180˚ swing:Full Surface Hinge. On fire labeledwood doors, the door leaf is hung usinga back plate with grommet nuts andbolts. Another popular application forthis type hinge is a tubular steel gatehung on a channel iron frame.

A fire labeled wood door (withoutsufficient hinge reinforcement) or akalamein (metal-clad wood door) withhollow metal frame. Recommended tohang door for 180˚ swing: Half SurfaceHinge. On fire labeled wood doors, thedoor leaf is hung using a back platewith grommet nuts and bolts.

Full Surface Hinge

Half Surface Hinge

Less common flush door/frame/wall conditions requiring different typehinges would include:

Page 12: Hinge Catalog

McKINNEYHingeCatalogHingeSelectionSpecial FlushDoor/Wall/FrameApplications

10May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

On high frequency and/or heavy woodor metal doors, additional anchoring ofthe hinges into the door and jamb maybe necessary. This is a commonapplication in schools, hospitals or anyother buildings where heavy traffic andunusual strain on the doors, jamb andhinges is experienced. Recommendedto hang door for 180˚ swing: FullMortise Anchor Hinge. Sold in sets ofone full mortise anchor hinge and twoheavy weight full mortise hinges.

Some door/frame/wall and even ceilingconditions make door closersimpractical. An alternative closingdevice is the Spring Hinge. Generally,at least two hinges on a door must bespring hinges to provide adequateclosing force. Note: NFPA requires aminimum of two (2) spring hinges onfire labeled doors. With adjustablespring tension on the hinge, theclosing speed of the door is determinedby the amount of closing force set onthe hinge. Spring hinges may not besuitable for applications requiring aclosing device with non-critical closingand latching speed adjustments. Withrespect to meeting ADA requirementsfor closing devices, carpeting and/orgasketing can interfere with latching.McKINNEY offers both Full Mortiseand Half Surface Spring Hinges.

McKinney now offers a ReverseAction,1502R, ( by special request)which allows the door to remain in theopen position. In addition, for highsecurity applications, we offer the TRSoption. This Tamper Resistant Screw isscrewed into the tension ratchet afterthe proper tension has been set.

Spring Hinge MCK 1572 (HALF SURFACE TYPE)MCK 1502 (FULL MORTISE TYPE)

Variations of the basic hinge types may be needed to accommodatespecial situations in flush door/frame/wall conditions:Note: General aforementioned guidelines regarding selection of basic hinge types with respect todoor and frame types including fire labeled and applicable to any variations of those hinge typeslisted hereafter. Variations may not be listed or available in all basic hinge types. Consult the factoryfor availability.

Anchor Hinge MCK TA792APPLICATION

Note: Anchor hinges are handed and sold foreither square edge doors on hinge side orbeveled (1⁄8" in 2") edge doors on hinge side.Hand and bevel (McKINNEY uses a “5” infront of the item number to indicate 1⁄8" in 2"bevel. Example: TA5792) should be specified.

Page 13: Hinge Catalog

McKINNEYHingeCatalogHingeSelectionSpecial FlushDoor/Wall/FrameApplications

11 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

A condition which is common inbarrier free openings, and especially inhospitals, is how to remove the dooredge from the opening at 90˚ of swingwith flush door/wall/ frame conditions.Recommended to hang door withswing to 180˚: Full Mortise SwingClear Hinge. The solution offered bythis hinge is the offset of the hingebarrel to a location along the face ofthe hinge jamb, thereby removing thedoor edge and the barrel of the hinge asobstacles in the opening at 90˚ or moreof swing. If the door is beveled on thehinge side, specify the appropriatebeveled hinge and handing for yourapplication*.

* Consult individual Swing Clear catalog pagesfor beveled hinge product numbers.

Swing Clear Hinge MCK TA2895APPLICATION

Meets or exceedsANSI A117.1 - 1986Providing Accessibilityand Usability forPhysicallyHandicapped People

Page 14: Hinge Catalog

McKINNEYHingeCatalogHingeSelectionNon-FlushDoor/Wall/FrameApplications

12May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Not all door/frame/wall conditions are flush and, in order to hang thedoor, other variations on the basic hinge types may be needed.

If the door is not flush with the frame,is sitting back in a deep reveal from theface of the frame with or withoutadditional obstacles created by appliedtrim on the face of the frame or adeeper reveal caused by a projectingwall, and the door is to swing 180˚, thena Full Mortise Wide Throw Hingemay be used in hanging the door.

Important in this regard is how tocalculate the proper width of a widethrow hinge (rounded to the nexthigher whole number if result is not awhole number: e.g., 6", 7", 8", etc.)

Wide Throw Hinge

1. If the door is sitting inside a deepframe reveal with no otherobstacles (i.e., projecting trim orwall), add the depth of the reveal(distance from the face of theframe to the face of the door) tothe recommended width of hingeused under flush conditions.Example: A 6" wide (wide throw)hinge would replace a 41⁄2" wideregular mortise hinge (used underflush conditions) if the depth ofthe reveal is 11⁄2".

2. If the door is to clear projectingtrim or wall and the barrel of thehinge is not obstructed, thencalculate as follows:

(a) double the size of the door

(b) subtract 1⁄2" if the doorthickness is less than or equal to21⁄4" or subtract 3⁄4" if the doorthickness is greater than 21⁄4"

(c) add for the additional depthfrom the face of the obstruction tothe face of the door

(d) add for clearance between thedoor and the face of theobstruction at 180˚ of swing(generally 1" or more).

If, for instance, you have a 13⁄4"thick door:

(a) 13⁄4" door thickness x 2 = 31⁄2"

(b)less 1⁄2" equals 3"

(c) plus 3" for the additional depthfrom the face of the wall to theface of the door equals 6"

(d) plus 1" for the clearancebetween the door and the face ofthe obstruction at 180˚ of swingequals 7" overall hinge width.

MCK TA2798APPLICATION

How to Calculate

Page 15: Hinge Catalog

McKINNEYHingeCatalogHingeSelection

13 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

An increasingly popular door, frameand wall condition in corridors iscross-corridor or double egress pairs ofdoors standing in wall pockets at 90˚ ofswing, so as to be clear of the initialopening and out of the corridoraltogether. Solution: Pocket Hinge.

As corridor doors are often firelabeled, the hardware must beapproved for use in fire labeledopenings. Solution: the McKINNEYPH-4 Pocket Hinge. U.L. approvedfor use on both hollow metal and steelcovered composite fire doors rated upto 3 hours and on wood core type firedoors rated 20 minutes.

Pocket Hinge

Recommended for use on averagefrequency double acting doors inschools, hospitals, institutions andother public buildings. Not for use onlabeled doors and frames.

Pivots

If the door is not flush with the framebut rather is sitting back in a deepreveal from the face of the frame a FullMortise Raised Barrel Hinge may beused in hanging the door. The solutionoffered by this hinge is the offset of thehinge barrel away from the hinge jamb.Bevel of door edge should be specified.

Raised Barrel Hinge

MCK PH-4APPLICATION

EP-5J

RAISEDBARRELSQUAREEDGEDOOR RAISEDBARRELBEVELEDEDGEDOOR

Page 16: Hinge Catalog

McKINNEYHingeCatalogHingeSelection

14May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Aluminum ContinuousHinges consist of two anodized, full-height, bearing-geared leaves that areheld together by a full-length channelcap. This design provides properalignment and eliminates prematurewear. The geared construction andfull-length channel cap seals the gapbetween the door and frame andprovides privacy and security againstprying. This feature also provides safetyagainst pinched fingers especially inpublic areas where children are apt tomove throughout the opening. Thegear design ensures identical operationof each leaf, and even-distribution ofload stress along the full length of the

door and frame which eliminates doorsag and binding. Mortising is notnecessary, and the hinge doubles asweather stripping on the hinge side.These hinges are tested and certifiedby UL® (USA & CANADA) tostandards UL 10C and UBC7.2(positive pressure) for up to a 3-hour(A-Label) Fire Listing for all4'0"x10'0" and 8'0"x10'0" door andframe assemblies. Fire testingcertification applies to all approvedhollow metal and wood doorassemblies in dry wall or masonry wallconstruction. FirePins™ are now onlyrequired on 3-Hour (A-label)Assemblies. These hinges have been

cycle tested using a 150 lb. Door andare now certified fully functional after1.5 million cycles. The screw holelocations on these hinges are ideallysuited for use on lead lined doors(i.e. hospital X-ray rooms. Refer to theAluminum Continuous Hinge pagesection for additional information.

McKINNEY Steel or Stainless ContinuousHinges are fabricated from independentlymachined 14 gauge cold rolled steeland finished in prime coat, or 304stainless steel door leaves. The hinge isheld together with a 1/4" stainless steelTeflon coated free moving rod. Thehinge works on a split bearing assemblywhich eliminates premature wear andguarantees proper alignment.

These hinges are UL® (USA &CANADA) up to a 3-hour (A-label)Fire Listing for 4'0"x8'0" single doorsand 8'0"x8'0" pairs of doors. Thenon-handed, slim barrel design isrecommended for new constructionand retrofit installations. Refer to theSteel and Stainless Continuous Hingepage section for additional information.

Aluminum Continuous Hinges

Steel and Stainless Steel Continuous Hinges

FULL SURFACE CENTER PIVOT 58HD SERIES

FULL MORTISE 12HD, 14HD, 25HD SERIES HALF-SURFACE 54HD SERIES FULL SURFACE 22HD SERIES

FULL SURFACE MCK-FS302

FULL MORTISE MCK-FM300, MCK-HG305, MCK-HG315 SWING CLEAR MCK-HG311

may be used as swing clear

Note: Not all products shown. Refer to pages 101 - 153 for additional information on our Aluminum Continuous and Steel &Stainless Continuous Hinges

Page 17: Hinge Catalog

McKINNEYHingeCatalogReferenceCharts

15 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Hollow Metal Door Weights by Gauge Wood Door Weights by Door ThicknessDoor Gauge – # Per Square Foot # Per Square Foot

20 Gauge Door 4 Door Thickness 1-3/8" 1-3/4"

18 Gauge Door 5 Particle/Mineral Core 4.75 5.25

16 Gauge Door 6 Stave Core Wood 3.75 4.25

14 Gauge Door 7 Hollow Core Wood 1.3 1.5

Door, FrameWall Conditions Frame Type Door Type Hinge Type

Variation ofBasic Hinge Type

Shown Below(See Note 2)

McKINNEYExample

(See Note 3)

Flush* Wood or Metal Wood or Metal Full Mortise (not applicable) TA2714

Flush* Channel Iron Wood or Metal Half Mortise (not applicable) TA2774

Flush* Channel Iron Kalamein or Fire LabeledWood Door (see Note 1)

Full Surface (not applicable) TA2771

Flush* Metal Kalamein or Fire LabeledWood Door (see Note 1)

Half Surface (not applicable) TA2772

Flush* MetalHeavy and/or

High FrequencyWood or Metal

Anchor Full Mortise TA792

Flush* Wood or Metal Wood or Metal RequiringAlternative Closing Device

Spring Full MortiseHalf Surface

1502, 1572

Flush* Wood or Metal Wood or Metal Requiredto Clear Opening at 90˚ of Swing

Swing Clear Full Mortise TA2895

Deep Frame Reveal Wood or Metal Wood or Metal with MaximumSwing of 90˚ to 110˚

Raised Barrel Full Mortise RBTA2714

Deep Frame Reveal with orwithout Trim on the Face of

the Frame or a Projecting WallWood or Metal

Wood or Metalwith swing to 180˚ Wide Throw Full Mortise TA2798

Wall Pocket at90˚ of swing

Metal Wood or Metal Pocket Hinge (not applicable) PH-4

The following wood and metal doorweights are provided as a convenienceto catalog users. They are approximateand will vary slightly among doormanufacturers. The weight of the doorhardware should be added to theweights listed below. For any thicknessnot shown, the individual manufacturer’scatalog should be consulted.

Door Weights (Based upon 3'0"x7'0" Door Size(Weights do not include hardware)

Quick Reference Chart

* Includes door and frame conditions of up to 1⁄8" inset

Notes:

(1) Fire labeledwooddoorwithout sufficienthinge reinforcement.Door leaf is hungusingbackplatewithgrommetnuts andbolts.

(2) The fourbasichinge types are fullmortise,halfmortise, full surface andhalf surface.Variations (i.e. anchor, swingclear, raisedbarrel,wide throw)are available in thebasictypes shownabovebutmaynotbeavailableinall basichinge types.Consult individualcatalogpages for availability.

(3) Consult individual catalogpages for availablesizes,weights,materials, versions, bearings andfinishes.Hinges for doors beveled (1⁄8" in2")onhinge sideuse5000 series for 3Khinges(e.g.TA5792); use4000 series for 5Khinges(e.g.,TA4895).

Door Weights

Page 18: Hinge Catalog

McKINNEYHingeCatalogReferenceCharts

16May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Knowing the door thickness and trimprojection, use the following formulafor determining minimum hinge widthof all full mortise hinges:

(1) Door thickness(2) Backset(3) Required Clearance(4) Inset

Door thickness minus the backsetmultiplied by 2, plus the requiredclearance, plus the inset (if applicable)will equal the proper hinge width.

D = Door ThicknessT = Trim DepthW = Hinge Width

Clearance"T"

"W"

"D"

For doors up to 21/2" thick:W=(2 x D) + T

For doors 21/2" to 3" thick:W=(2 x D)+(2 x T)+ 1/4"

Door Heightin Inches (MM)

# of HingesPer Door

Up to 60 (1524) 2

60 to 90 (1524 to 2286) 3

90 to 120 (2286 to 3048) 4

Recommended Number of Hingesper Door 3'0" Wide (Wood or Metal)

Expected Frequency of Door OperationHow to Determinethe Proper Hinge Width

One Cycle = one complete opening and closing

Expected FrequencyInstallation Type Daily Yearly

COMMERCIAL

Commercial Store Entrance 5,000 1,5000,000Office Building Entrance 4,000 1,200,000Theatre Entrance 1,000 450,000School Entrance 1,250 225,000School Restroom Door 1,250 225,000Store or Bank Entrance 500 150,000Office Building Restroom Door 400 118,000School Corridor Door 80 15,000Office Building Corridor Door 75 22,000Store Restroom Door 60 18,000

RESIDENTIAL

Entrance 40 15,000Restroom Door 25 9,000Corridor Door 10 3,600Closet Door 6 2,200

Note: We recommend that bearing hinges be used on allabove categories other than “Residential”.

Low

Ave

rage

High

Door Hinge Max ClearanceThickness Width Provided

13⁄8" 31⁄2" 11⁄4"4" 13⁄4"

13⁄4" 4" 1"41⁄2" 11⁄2"

5" 2"

6" 3"

2" 41⁄2" 1"5" 11⁄2"6" 21⁄2"

21⁄4" 5" 1"6" 2"

Trim Clearance

The table above indicates the trimclearance provided by hinges of specifiedwidths on flush doors, not inset, ofstandard thickness. For doors of otherthicknesses, apply the proper formula.

The hinge widths of half mortise, halfsurface and full surface hinges arestandard, depending on the hinge length.Note that in these hinge types, theamount of clearance available isdetermined by the amount of offset andnot by the hinge width.

Recommended Size of Hinges per Door (Wood or Metal)

13⁄8 (35)

13⁄8 (35)

13⁄4 (44)

13⁄4 (44)

13⁄4 (44)

2 - 21⁄2 (51 - 64)

2 - 21⁄2 (51 - 64)

31⁄2 (89)

4 (102)

41⁄2 (114)

5 (127)

6 (152)

5 (127) HW

6 (152) HW

*

*

*

Note: Another hinge is required for eachadditional 30"

* Heavy weight hinges should be used on allextra heavy doors or those exposed to highfrequency use. Consult the factory for doorswider than 3'0". Five knuckle heavy weighthinges are four bearing. The following gaugesof metal may apply:

Heavy weight 4-1⁄2" (114) high = .180 gaugeHeavy weight 5" (127) high = .190 gaugeHeavy weight 6" (152) high = .203 gauge

Note:Five knuckle 8" (203) high hinges havesix bearings.

Note:On hinge size the dimension shown is the hingeheight. Where full mortise or other hinges withtwo dimensions are used, the first dimensiongiven is always the height. The seconddimension is the hinge width when open.

Up to 36 (914) .123

Over 36 (914) .130

Up to 36 (914) .134

Over 36 - 48(914 - 1219)

.134

Over 48 (1219) .160

Up to 42 (1067) .190

Over 42 (1067) .203

Door Thicknessin Inches (MM)

Door Widthin Inches (MM)

Hinge Heightin Inches (MM)

HingeGauge

Page 19: Hinge Catalog

McKINNEYHingeCatalogReferenceCharts

17 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

The top of the top hinge should be 5" from thejamb header.The bottom of the bottom hinge should be 10"from the finished floor.The center of the center hinge should beequidistant from the other two.EXCEPTION:The McKINNEY Anchor Hinge mounts at thevery top of the door.On doors over 7’6" high, fourhinges are required.

For 13⁄4" (44.5mm) or Thicker Doors3 11⁄2 1 3⁄4 1⁄2 1⁄3 4 (1.22) 10 (3.05) 41⁄2 (114.3) 0.180 (4.57) Steel, Mortise or Surface3 11⁄2 1 3⁄4 1⁄2 1⁄3 4 (1.22) 8 (2.44) 41⁄2 (114.3) 0.134 (3.40) Steel, Mortise or Surface

11⁄2 3⁄4 1⁄2 1⁄3 3’2" (0.96) 8 (2.44) 6 (152.4) 0.225 (5.72) Steel-Olive Knuckle or Paumelle3 11⁄2 3⁄4 1⁄2 1⁄3 4 (1.22) 10 (3.05) 4 (101.6) 0.225 (5.72) Steel Pivots (including top, bottom and intermediate)

11⁄2 1 3⁄4 1⁄2 1⁄3 3 (0.91) 5 (1.52) 4 (101.6) 0.130 (3.30) Steel Mortise or Surface11⁄2 1 3⁄4 1⁄2 1⁄3 2 (0.61) 3 (0.91) 3 (76.2) 0.092 (2.34) Steel, Mortise or Surface

3 11⁄2 1 3⁄4 1⁄2 1⁄3 3 (0.91) 7 (2.13) 41⁄2 (114.3) 0.134 (3.40) Steel, Mortise or Surface (labeled self closing spring type)3 11⁄2 1 3⁄4 1⁄2 1⁄3 3 (0.91) 7 (2.13) 4 (101.6) 0.105 (2.67) Steel, Mortise or Surface (labeled self closing spring type)

For 13⁄8" (34.93mm) Doors3 11⁄2 3⁄4 1⁄2 1⁄3 3 (0.91) 7 (2.13) 31⁄2 (88.9) 0.123 (3.12) Steel, Mortise or Surface3 11⁄2 1 3⁄4 1⁄2 1⁄3 2’8" (0.81) 7 (2.13) 31⁄2 (88.9) 0.105 (2.67) Steel, Mortise (spring closing)

Notes:

(1) All hinges or pivots, except spring hinges, shall beof the ball-bearing type. Hinges or pivotsemploying other antifriction bearing surfaces arepermitted if they meet the test requirements ofANSI A156.1, Standard for Butts and Hinges. Springhinges shall be labeled.

(2) 41⁄2" (114mm) high, 0.180" (4.57mm) thick hingesshall be permitted for use on wide and heavy doorsor doors that are subjected to heavy use or unusualstress.

(3) Some manufacturers can provide fire doors withhinges of lighter weight that are not of the ballbearing type where they are part of a listedassembly and meet the test requirements of ANSI

A156.1, Standard for Butts and Hinges, and havebeen tested to a minimum of 350,000 cycles.

(4) Pivot sets made up of components that are smallerand/or of a lighter gauge than shown in Table 2-8.1.1 shall be permitted to be used, provided theymeet the requirements of ANSI A156.4, DoorControls (Closers) and are in accordance with themanufacturers’ labeled service procedures.

Maximum Door Size Minimum Hinge SizeDoor Rating, Hr. Width ft. (m) Height ft. (m) Height in. (mm) Thickness in. (mm) Type Hinge

Table 1 Reference NFPA-80 Table 2-8.1.1 1995 Builders Hardware

The requirements of the Underwriters’Laboratories, Inc., for fire doorhardware are determined by door label,which in turn is established by thelocation of the opening. The followingare the classifications of Underwriter’sLaboratories, Inc.

On all public and some private heavyconstruction three hinges are requiredfor each door. This practice is standardunder U.S. Government specificationsand is required under most buildingcodes and Fire Underwriters’specifications.

Three hinges assure proper dooralignment and enable other hardware

to function properly. There is less doorwarping and less hinge wear. On lightwood doors the alignment problem isas great as on heavy doors so less thanthree hinges should never beconsidered.

DoorSituation

Location

Class A Fire Walls

Class B Vertical Shafts

Class C Corridor & Room Partitions

Class DExterior Walls(severe fire exposure)

Class DExterior Fire Escapes(severe fire exposure)

Class EExterior Wallsmoderate fire exposure)

Class EExterior Fire Escapes(moderate fire exposure)

Underwriters’ LaboratoriesRequirements

5"

EQUAL

EQUAL

10"

Mortise and Surface Hinges, Pivots or Spring Hinges for Swinging Doors. Doors up to 60“ (1.52 m) in height shall be provided with two hinges and an additional hinge for each additional 30" (0.76 m) of doorheight or fraction thereof. The distance between hinges shall be permitted to exceed 30" (0.76 m). Where spring hinges are used, at least two shall be provided.

Reprinted with permission from NEPA 80, Fire Doors and Fire Windows, Copyright ©1995, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association on thereferenced subject which is represented only by the standard in its entirety.

Page 20: Hinge Catalog

McKINNEYHingeCatalogHandofDoors andHinges

18April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All doors are handed - right or left. The following illustrations indicate clearly this“handing” as it is understood within the hardware industry.

(Hand of door is determined from the outside)When standing on outside of door and hinges are on the right, it is right hand.When hinges are on the left, it is left hand.

A double acting door opens from you and toward you, therefore it is not calledreverse like a single acting door.

Hand of Doors

McKINNEY Anchor Hinges arehanded right or left as are McKINNEYModerne. Full surface, half surface andhalf mortise hinges with set screw(NRP) in the barrel are manufacturedas reversibles (with no hole in plug).Continuous hinges are handed whencut to size, or when ordered withelectrical modifications.

Hand of Hinges

REGULAR DOORS OPENING IN

OUTSIDELeft Hand Door takes left hand hinges

OUTSIDERight Hand Door takes right hand hinges

REVERSE DOORS OPENING OUT

OUTSIDELeft Hand Reverse Door takes right hand hinges

OUTSIDERight Hand Reverse Door takes left hand hinges

DOUBLE ACTING

Left Side of HingeLeft Hand Door

Right Side of HingeRight Hand Door

Right Side of Hinge Left Side of Hinge

Outside

A simple method of determiningthe hand of all loose joint hinges is toopen the hinge full with the countersunkscrew holes in view. If the hinge can beheld by the right hand leaf and it doesnot fall apart, it is a right hand (RH)hinge. If the hinge must be held by theleft hand leaf to keep it from fallingapart, it is a left hand (LH) hinge.

The hand of hinges may bespecified by suffixing the symbols RHor LH to the catalog number.

Page 21: Hinge Catalog

McKINNEYHingeCatalogHingeSwaging

19 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All hinges for full mortise applicationsare swaged. Normal swaging onstandard and heavy gauge hingesprovides a clearance of 1⁄16" when theleaves are parallel. Full mortise widethrow hinges have a clearance of 3⁄32".

Swaging is the slight offset in the hinge leaves which permits them toclose to a parallel position as the door closes.

Full Mortise

Hinges for full surface applications arenot swaged. Blank hinges are for fullsurface welded application and arealways furnished “flat back” unlessspecified otherwise when ordered.

Full Surface

Hinges for beveled door applicationshave one leaf swaged at an angle of31⁄2˚ (1⁄8" in 2") to maintain properdoor and frame clearance when doorsare beveled on the hinge side. Specifyhanding on these hinges.

Beveled Door

When only one leaf is swaged, the non-swaged leaf is approximately 1⁄16"shorter as a standard. For all hollowmetal door and frame applications,both leaves must be the same width.On your order, specify “Leaves mustbe equal”.

One Leaf Swaged

When only one leaf is swaged flat, thenon-swaged leaf is approximately 3⁄32"shorter as a standard. For all hollowmetal door and frame applications,both leaves must be the same width.On your order, specify “Leaves mustbe equal”.

One Leaf Swaged Flat

Hinge with One Leaf Swaged Hinge with One Leaf Swaged Flat

Hinge Opened

Hinge Closed

Hinge Opened

Hinge Closed

Hinge Opened

Hinge Closed

Page 22: Hinge Catalog

McKINNEYHingeCatalogScrews andFasteners

20May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY hinges are manufacturedwith templated screw hole locationsand tolerances which conform to theAmerican National Standards Institute(ANSI/BHMAA-156.7). McKINNEYpublishes a complete listing oftemplates which list the overall hingesize, material gauge and exact screwhole location. The most currenttemplates are found on our website @www.mckinneyhinge.com. Thesetemplates should be consulted prior toany door or frame preparation.

MACHINE AND WOOD SCREWS

McKINNEY offers a wide variety ofscrews and fasteners.

Shown:1.TorxBit andDriver2.SpannerBit andDriver3.PhillipsHeadMachineScrew4.TorxHeadMachineScrew5.SpannerHeadMachineScrew6.TorxHeadWoodScrew7.SpannerHeadWoodScrew8.PhillipsHeadWoodScrew9.OvalPhillipsHeadMachineScrewwithGrommetNut

TORX DRIVER & SPANNER DRIVER

TEMPLATED SCREW HOLES

1

2

93 4 5 6 7 8

Page 23: Hinge Catalog

McKINNEYHingeCatalogScrews andFasteners

21 May

2008

©McK

INNEYProductsCom

pany2006,2007,2008

1-800-346-7707 • www.mckinneyhinge.com

Full Mortise Hinges

31⁄2 x 31⁄2 1⁄2 x 10-24 1 x 1031⁄2 x 5 1⁄2 x 10-24 1 x 104 x 4 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 124 x 6 1⁄2 x 12-24 11⁄4 x 124 x 7 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 6 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 7 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 8 1⁄2 x 12-24 11⁄4 x 125 x 4 1⁄2 x 12-24 11⁄4 x 125 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 5 1⁄2 x 12-24 11⁄4 x 125 x 7 1⁄2 x 12-24 11⁄4 x 125 x 8 1⁄2 x 12-24 11⁄4 x 126 x 5 1⁄2 x 1⁄4-20 11⁄4 x 146 x 6 1⁄2 x 1⁄4-20 11⁄4 x 148 x 6 1⁄2 x 1⁄4-20 11⁄4 x 148 x 8 1⁄2 x 1⁄4-20 11⁄4 x 14

Size of Hinge Machine WoodScrews Screws

All contract grade size 2-Knuckle,3-Knuckle and 5-Knuckle hinges arepacked all machine (8 each) x allwood (8 each) screws.

Packing:

41⁄2 1⁄2 x 12-24

5 1⁄2 x 12-24

6 1⁄2 x 1⁄4-20

MachineSize of Hinge Screws

Swing Clear Hinges

41⁄2 1⁄2 x 12-24 1-1⁄4 x 12

5 1⁄2 x 12-24 1-1⁄2 x 12

Machine WoodSize of Hinge Screws Screws

Full Surface Hinges

41⁄2 1⁄2 x 12-24 2 x 1⁄4-20

5 1⁄2 x 12-24 2 x 1⁄4-20

6 1⁄2 x 1⁄4-20 2 x 1⁄4-20

Machine Thru Bolts &Size of Hinge Screws Grommet Nut

Half Surface Hinges

41⁄2 1⁄2 x 12-24 2 x 1⁄4-20

5 1⁄2 x 12-24 2 x 1⁄4-20

6 1⁄2 x 1⁄4-20 2 x 1⁄4-20

Machine Thru Bolts &Size of Hinge Screws Grommet Nut

Half Mortise Hinges

*

*

31⁄2 x 31⁄2 3/4 x 9

4 x 4 1 x 9

WoodSize of Hinge Screws

*1400-1414-1458 Residential Grade

Page 24: Hinge Catalog

McKINNEYHingeCatalogFinishes

22March

2008

©McK

INNEYProductsCom

pany2006,2007,2008

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY and Government Finish Symbols

McKINNEYPowder Coat Finishes

Aluminum AP

Beige PB

Gold PG

Grey Tone GT

White PW

Bright Brass with Clear Powder Coat 3-C

Dull Brass with Clear Powder Coat 4-C

Dull Nickel with Clear Powder Coat 15-C

Co-Laq - Dark D-3

Co-Laq - Black D-4

Custom Polymer Coating *

Prime Coat P

Every effort is made by McKINNEY tofurnish finishes which do comply withthe U.S. Standard. However, wecannot guarantee that our finish willmatch other manufacturers’ finish.Where a special finish or a matchedfinish is required, a sample must besubmitted with the order.

As part of their promise to provideinnovative solutions to their customers,certain ASSA ABLOY Group brandsoffer the MicroShield® technology, asilver-based antimicrobial coatingdesigned to inhibit the growth ofbacteria.

MicroShield® is a registered trademarkof Yale Security Inc., an ASSA ABLOYGroup company.

· Suppresses microbes· Long lasting· Non-toxic· Available on McKINNEY stainlesshinges· Lasts for the life of the hardware· Specify 32DMS

McKINNEY’s electrostatically appliedpolyester powder finishes have beentested to exceed all recommendedsalt-spray testing requirements. Thesefinishes have also been proven to be byfar the best finish for steel hinges in areaswhere hardware is susceptible to corrosionsuch as caused by high humidity, moistureor coastal environments.

U.S. Finish Description McKINNEY

US P Primed for Painting P

US 3 Bright Brass 3

US4 Dull Brass 4

US5 Dull Brass, Oxidized 5*

US7 Brass, Nickel Oxidized, Bright Relieved 7*

US9 Bright Bronze 9*

US10 Dull Bronze 10

US10A Antiqued Bronze, Oiled and Lacquered 10A

US10B Antiqued Bronze, Oiled 10B

US11 Dull Bronze, Oxidized 11*

US14 Bright Nickel Plated 14

US15 Dull Nickel Plated 15

US15A Nickel Oxidized Relieved 15A*

US17A Half Polished Iron, Smooth 17A*

US 20 Statuary Bronze, Light 20*

US 20A Statuary Bronze, Dark 20A*

US 26 Bright Chromium 26

US 26D Dull Chromium 26D

US 32 Polished Stainless Steel 32

US 32D Dull Stainless Steel 32D

Antique Bronze, Over Stainless 32D x 10B

* Consult the factory for availability of these finishes.

Page 25: Hinge Catalog

McKINNEYHingeCatalogFinishes

23 March

2008

©McK

INNEYProductsCom

pany2006,2007,2008

1-800-346-7707 • www.mckinneyhinge.com

B.H.M.A.Code

Finish Description Base MaterialMcKINNEYEquivalent

600 Primed for Painting Steel USP

602 Zinc Plated, Commercial Steel US2C

603 Zinc Plated, Governmental Steel US2G

605 Bright Brass Brass US3

606 Dull Brass Brass US4

609 Dull Brass, Oxidized Brass US5

610Brass, Nickel Oxidized, BrightRelieved

Brass US7

611 Bright Bronze Bronze US9

612 Dull Bronze Bronze US10

613 Antiqued Bronze, Oiled Bronze US10B

616 Dull Bronze, Oxidized Bronze US11

618 Bright Nickel Plated Brass, Bronze US14

619 Dull Nickel Plated Brass, Bronze US15

620 Nickel Oxidized Relieved Brass, Bronze US15A

621 Half Polished Iron, Smooth Brass, Bronze US17A

623 Statuary Bronze, Light Bronze US20

624 Statuary Bronze, Dark Bronze US20A

625 Bright Chromium Brass, Bronze US26

626 Dull Chromium Brass, Bronze US26D

629 Polished Stainless SteelStainless Steel300 Series

US32

630 Dull Stainless SteelStainless Steel300 Series

US32D

632 Bright Brass Steel US3

633 Dull Brass Steel US4

636 Dull Brass, Oxidized Steel US7

637 Bright Bronze Steel US9

639 Dull Bronze Steel US10

640 Antique Bronze, Oiled Steel US10B

643 Dull Bronze, Oxidized Steel US11

645 Bright Nickel Plated Steel US14

646 Dull Nickel Plated Steel US15

647 Nickel Oxidized Relieved Steel US15A

648 Half Polished Iron, Smooth Steel US17A

649 Statuary Bronze, Light Steel US20

650 Statuary Bronze, Dark Steel US20A

651 Bright Chromium Steel US26

652 Dull Chromium Steel US26D

McKINNEY and B.H.M.A. Finish Symbols McKINNEY hinge finishes meet orexceed the American National Standardsfor materials and finishes (ANSI/BHMA- A156.18 and BHMA 1301).

Ferrous BaseSteel base hinges which are

polished and plated are dipped inlacquer, baked and dried. US4 Finishover steel, a purely decorative finishwhich in the past was susceptible topitting is now furnished with a nickelbase for added durability, and followedby 20 minutes of brass and then lacquered.This new process allows McKinney tohave one of the best US4 finish in theindustry. However, brass finishes oversteel should not be cleaned with anytype of paint remover or abrasivemethod which will remove the lacquer.

Our US10B is a true oil rubbedfinish. However, due to excessivehandling on installation of electrichinges and sample cards, we use a 10BLwith a very light lacquer to protect thefinish. 10B over stainless is a beautifulfinish available thru McKinney.

Steel hinges which are supplied inprime coat are finished with Powder CoatPrime finish which is ready for paintingin the field, or durable enough to letstand on its own.

Non-Ferrous Base (should be usedfor exterior installations).

Brass or Bronze hinges are polishedand plated.

Stainless Steel hinges are passivatedto remove any impurities in the stainlessmaterial, then polished to a satin finish(US32D) or can be polished to a brightfinish (US32).

*

*

*

***

*

* Consult the factory for availability of these finishes.

Page 26: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2008

1-800-346-7707 • www.mckinneyhinge.com

StormPro® 5K heavy weight full mortisehinges are packed with stainless screws,all machine screws.

Packing:

• NRP(non-removablepin)

Required component of the integrated StormPro unit, including the frame and door, along with otherStormPro hardware.

Steel material polished and plated orfurnished in powder coat.

41⁄2 x 41⁄2 114.3 x 114.3 .180

5 x 41⁄2 127 x 114.3 .180

Stainless steel base material polished.

Available Sizes

Inches MM Gauge

SP3386 SP3786 Available Options:

• Built towithstandextremewind speedsand flyingdebris associatedwith severeweather conditions

• Packedwith stainlessmachine screws• Fire rated thru 3hours• Part of the integratedunit whenusedwithCECOStormPro® 361,CURRIESStormPro® 331andBARON F-5doors and frames, alongwithotherStormPro® harwarebyASSAABLOYCompanies

Features:

A5111 StainlessA8111 Steel

ANSI Cross Reference:

APPLICATION

41⁄2 x 41⁄2 1⁄2 x 12-24

5 x 41⁄2 1⁄2 x 12-24

Full Mortise Hinge Fasteners

Hinge Size Machine

StormPro®

McKINNEY HingeCatalogFull Mortise Bearing HingesFive Knuckle Heavy Weight StormPro® Series

24March

2008

Page 27: Hinge Catalog

McKINNEYHingeCatalogFullMortisePlainBearingHingesTwoKnuckle StandardWeight Series

25 March

2008

©McK

INNEYProductsCom

pany2006,2007,2007

1-800-346-7707 • www.mckinneyhinge.com

Steel base polished and plated or furnished in powder coat finish.

31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .13041⁄2 x 4 114.3 x 101.6 .134

41⁄2 x 41⁄2 114.3 x 114.3 .134

Available Sizes

Inches MM Gauge

31⁄2 x 31⁄2 1⁄2 x 10-24 11⁄4 x 124 x 4 1⁄2 x 10-24 11⁄4 x 12

41⁄2 x 4 1⁄2 x 10-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 10-24 11⁄4 x 12

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

All 2K standard weight full mortiseplain bearing steel hinges are packed allmachine x all wood screws. For specialscrews consult price book on avail-ability. Specify hand when ordering.

Not recommended for medium or high frequency doors, or doors with closing devices.

T2731

• NRD(non-removabledoor - onedoweledhinge furnishedper set)

• RC (roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• SSF(safety stud feature)• BeveledEdge (wheredoors areonhinge side specifyT4731)

APPLICATION

Available Options:

A8133 Steel

ANSI Cross Reference:

Packing:

Page 28: Hinge Catalog

McKINNEYHingeCatalogFullMortise BearingHingesTwoKnuckle StandardWeight Series

26April2010

©McK

INNEYProductsCom

pany2006,2007,2008,2010

1-800-346-7707 • www.mckinneyhinge.com

• NRD(non-removabledoor - onedoweledhinge furnishedper set)

• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• SSF(safety stud feature)• CC-4(concealedcircuit - 4wire)• CC-6(concealedcircuit - 6wire)*• MM(magneticmonitoring)• BeveledEdge (wheredoorsarebeveledonhingesidespecifyTA4331orTA4731)

All 2K standard weight full mortisebearing hinges are packed all machinex all wood screws. For special screwsconsult price book on availability.Specify hand when ordering.

Recommended for standard weight, medium frequency doors, or doors with closing devices.

Stainless steel or available in brass basematerial polished and plated orfurnished in powder coat.

Steel base polished and platedor furnished in powder coat finish.

31⁄2 x 31⁄2* 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .13041⁄2 x 4 114.3 x 101.6 .13441⁄2 x 41⁄2 114.3 x 114.3 .134

5 x 41⁄2 127 x 114.3 .146

5 x 5 127 x 127 .146

* Not available in Stainless

TA3331 TA2731

Available Sizes

Inches MM Gauge

APPLICATION

Available Options:

A2112 Brass, BronzeA5112 StainlessA8112 Steel

ANSI Cross Reference:

Packing:

31⁄2 x 31⁄2 1⁄2 x 10-24 1 x 104 x 4 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 5 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 29: Hinge Catalog

McKINNEYHingeCatalogFullMortise BearingHingesTwoKnuckleHeavyWeight Series

27 March

2008

©McK

INNEYProductsCom

pany2006,2007,2008

1-800-346-7707 • www.mckinneyhinge.com

• NRD(non-removabledoor - onedoweledhinge furnishedper set)

• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• SSF(safety stud feature)• CC-4(concealedcircuit - 4wire)• CC-6(concealedcircuit - 6wire)*• MM(magneticmonitoring)• BeveledEdge(wheredoorsarebeveledonhingesidespecifyTA5350orTA5750)

All 2K heavy weight full mortisebearing hinges are packed all machinex all wood screws.For special screws consult price bookon availability. Specify hand whenordering.

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.

Stainless steel base or available inbrass or bronze base material polishedand plated or powder coat.

Steel base polished and platedor furnished powder coat finish.

41⁄2 x 41⁄2 114.3 x 114.3 .1805 x 41⁄2 127 x 114.3 .1905 x 5 127 x 127 .190

* Not available in Stainless

TA3350 TA3750

Available Sizes

Inches MM Gauge

Available Options:

A2111 Brass, BronzeA5111 StainlessA8111 Steel

ANSI Cross Reference:

Packing:APPLICATION

41⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

5 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 5 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 30: Hinge Catalog

McKINNEYHingeCatalogFullMortisePlainBearingHingesThreeKnuckleStandardWeight Series

28March

2008

©McK

INNEYProductsCom

pany2006,2007,2008

1-800-346-7707 • www.mckinneyhinge.com

Steel base polished and plated or furnished in powder coat finish.

All 3K standard weight full mortiseplain bearing hinges are packedall machine x all wood screws.For special screws consult price bookon availability.

Not recommended for medium or high frequency doors, or doors with closing devices.

31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .13041⁄2 x 4 114.3 x 101.6 .134

41⁄2 x 41⁄2 114.3 x 114.3 .134

5 x 41⁄2 127 x 114.3 .146

5 x 5 127 x 127 .146

Available Sizes

Inches MM Gauge

T714

• NRP(non-removablepin)• ET(exposed tip)• RC (roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• SSF(safety stud feature)• BeveledEdge (wheredoors arebeveledonhinge side specifyT5714)

Available Options:

A8133 Steel

ANSI Cross Reference:

Packing:APPLICATION

31⁄2 x 31⁄2 1⁄2 x 10-24 1 x 104 x 4 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

5 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 5 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 31: Hinge Catalog

McKINNEYHingeCatalogFullMortiseBearingHingesThreeKnuckle StandardWeight Series

29 April2010

©McK

INNEYProductsCom

pany2006,2007,2008,2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K standard weight full mortisehinges are packed with all machineand all wood screws. For special screwsconsult price book on availability.

Packing:

• NRP(non-removablepin)• ET(exposedpinandplug)• RC(roundcorner - 1⁄4"radius furnishedunless specifiedotherwise)

• HT(hospital tip)• SSF(safety stud feature)• QC(ElectroLynxhinge)2, 4, 6, 8, 10or12wire available

• CC(concealedcircuit) 4, 6or8wireavailable

• MM(magneticmonitoring)• BeveledEdge(wheredoorsarebeveledonhingesidespecifyTA5314orTA5714)

Recommended for standard weight, medium frequency doors, or doors withclosing devices.

Stainless steel or available in brass basematerial polished and plated orfurnished in powder coat.

Steel base polished and platedor furnished in powder coat finish.

31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .13041⁄2 x 4 114.3 x 101.6 .134

41⁄2 x 41⁄2 114.3 x 114.3 .134

5 x 41⁄2 127 x 114.3 .146

5 x 5 127 x 127 .146

Available Sizes

Inches MM Gauge

TA314 TA714 Available Options:

A2112 Brass, BronzeA5112 StainlessA8112 Steel

ANSI Cross Reference:

APPLICATION

Page 32: Hinge Catalog

McKINNEYHingeCatalogFullMortiseBearingHingesThreeKnuckleHeavyWeight Series

30April2010

©McK

INNEYProductsCom

pany2006,2007,2008,2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight full mortise hingesare packed with all machine and allwood screws. For special screws consultprice book on availability.

Packing:

• NRP(non-removablepin)• ET(exposedpinandplug)• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• HT(hospital tip)• SSF(safety stud feature)• QC(ElectroLynxhinge)2, 4, 6, 8, 10or12wire available

• CC(concealedcircuit) 4, 6 or8wireavailable

• MM(magneticmonitoring)• BeveledEdge (wheredoors arebeveledonhinge side specifyTA5386orTA5786)

• 8x6 furnished in steel only (hole patterndiffers fromphoto shown)

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.

Stainless steel or available in brass basematerial polished and plated orfurnished in powder coat.

41⁄2 x 41⁄2 114.3 x 114.3 .180

5 x 41⁄2 127 x 114.3 .190

5 x 5 127 x 127 .190

6 x 5 152.4 x 127 .2036 x 6 152.4 x 152.4 .203

8 x 6* 203.2 x 152.4 .225

Steel base material polished and platedor furnished in powder coat.

Available Sizes

Inches MM Gauge

TA386 TA786 Available Options:

A2111 Brass, BronzeA5111 StainlessA8111 Steel

ANSI Cross Reference:* Consult templates 046A and 046B forappropriate hole pattern.Maximum door size for 8 x 6 is 4'0 x 8'0 600 lbs.

APPLICATION

41⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 5 1⁄2 x 12-24 11⁄4 x 12

6 x 5 1⁄2 x 1⁄4-20 11⁄2 x 146 x 6 1⁄2 x 1⁄4-20 11⁄2 x 148 x 6 1⁄2 x 1⁄4-20 11⁄2 x 14

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 33: Hinge Catalog

McKINNEYHingeCatalogFullMortise InstitutionalHingesThreeKnuckleHeavyWeight Series

31 February2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight full mortiseinstitutional hinges are packed with allTorx Head Security machine screws.For special screws consult price bookon availability.

Packing:

• PSF(prison safety feature)(shownbelow)• CC-4(concealedcircuit - 4wire)• MM(magneticmonitoring)*• BeveledEdge (wheredoors arebeveledonhinge side specify change toIHTB5386, IHTB5786

*NotavailablewithPSFoption

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where security requirements exist.

Stainless steel base material polishedand passivated or sand blasted andfurnished in prime coat. Hospitaltipped ends, double stainless steeldowel construction, concealedbearing assemblies.

41⁄2 x 41⁄2 114.3 x 114.3 .180

5 x 41⁄2* 127 x 114.3 .190

Steel base material polished and platedor furnished in powder coat. Hospitaltipped ends, double stainless steeldowel construction, concealed bearingassemblies.

Available Sizes

Inches MM Gauge

IHTB386 IHTB786

PRISON SAFETY FEATURE (PSF)(OPTIONAL)

HOSPITAL TIP (HT)

Available Options:

A5111 StainlessA8111 Steel

ANSI Cross Reference:

APPLICATION

Institutional Hinge Fasteners Torx PinHead Machine 1/2 x 12 - 24

Wood Screws supplied by request only1-1/4 x 12 Torx Pin Head

Page 34: Hinge Catalog

McKINNEYHingeCatalogSwingClear FullMortiseBearingHingesThreeKnuckleHeavyWeightSeries(Reversible)

32March

2008

©McK

INNEYProductsCom

pany2006,2007,2008

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight full mortise hingesare packed with all machine and allwood screws. For special screws consultprice book on availability. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.

Packing:

• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• HT(hospital tip)• SSF(safety stud feature)• MM(magneticmonitoring)• BeveledEdge (wheredoors arebeveledonhinge side specifyTA5795)

Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced. Hinge allows for maximum clearance for passage of beds, tables or other equipment throughdoorway. Pressed steel jambs require no special reinforcing.

Steel base material polished and plated or furnished in powder coat.

41⁄2 114.3 .1805 127 .190

Available Sizes

Inches MM Gauge

TA795 Available Options:

A8121 Steel

ANSI Cross Reference:

APPLICATION

41⁄2 1⁄2 x 12-24 11⁄4 x 12

5 1⁄2 x 12-24 11⁄4 x 12

Swing Clear Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 35: Hinge Catalog

McKINNEYHingeCatalogFullMortisePlainBearingHingesFiveKnuckle StandardWeight Series

33 April2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 5K standard weight full mortisehinges are packed with all machine andall wood screws. For special screwsconsult price book on availability.

Packing:

Stainless steel base or available inbrass base material polished and platedor furnished in powder coat.

Steel base polished and platedor furnished in powder coat finish.

• NRP(non-removablepin)• RC (roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• HT(hospital tip)• BT(ball tip)• ST(steeple tip)• SSF(safety stud feature)• BeveledEdge (wheredoors arebeveledonhinge side specifyT4314orT4714)

Not recommended for medium or high frequency doors, or doors with closing devices.

31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .13041⁄2 x 4 114.3 x 101.6 .134

41⁄2 x 41⁄2 114.3 x 114.3 .134

5 x 41⁄2 127 x 114.3 .146

5 x 5 127 x 127 .1466 x 6* 152.4 x 152.4 .160

*Not available in Stainless

Available Sizes

Inches MM Gauge

T2314 T2714 Available Options:

A2133 Brass, BronzeA5133 StainlessA8133 Steel

ANSI Cross Reference:

APPLICATION

31⁄2 x 31⁄2 1⁄2 x 10-24 1 x 104 x 4 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 5 1⁄2 x 12-24 11⁄4 x 126 x 6 1⁄2 x 1⁄4-20 11⁄2 x 14

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 36: Hinge Catalog

McKINNEYHingeCatalogFullMortiseBearingHingesFiveKnuckle StandardWeight Series

34April2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

• NRP(non-removablepin)• TB(ball bearing)• TCA(concealedbearing)• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• HT(hospital tip)• BT(ball tip)• ST(steeple tip)• SSF(safety stud feature)• QC(ElectroLynxhinge)2, 4, 6, 8, 10or12wire available

• CC(concealedcircuit) 4, 6or8wireavailable*

• MM(magneticmonitoring)• Slip In (Type1orType2)• BeveledEdge(wheredoorsarebeveledonhingesidespecifyTA4314orTA4714)

All 5K standard weight full mortisehinges are packed with all machine andall wood screws. For special screwsconsult price book on availability.

Recommended for standard weight, medium frequency doors, or doors with closing devices.

Stainless steel base or available inbrass base material polished and platedor furnished in powder coat.

Steel base polished and platedor furnished in powder coat finish.

31⁄2 x 31⁄2 88.9 x 88.9 .1234 x 4 101.6 x 101.6 .13041⁄2 x 4 114.3 x 101.6 .134

41⁄2 x 41⁄2 114.3 x 114.3 .134

5 x 41⁄2 127 x 114.3 .146

5 x 5 127 x 127 .1466 x 6* 152.4 x 152.4 .160

*Not available in Stainless

Available Sizes

Inches MM Gauge

TA2314 TA2714 Available Options:

A2112 Brass, BronzeA5112 StainlessA8112 Steel

ANSI Cross Reference:

Packing:APPLICATION

31⁄2 x 31⁄2 1⁄2 x 10-24 1 x 104 x 4 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 125 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

5 x 5 1⁄2 x 12-24 11⁄4 x 126 x 6 1⁄2 x 1⁄4-20 11⁄2 x 14

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 37: Hinge Catalog

McKINNEYHingeCatalogWideThrowFullMortiseBearingHingesFiveKnuckle StandardWeight Series

35 June2010

©McK

INNEYProductsCom

pany2006,2007,2008,2010

1-800-346-7707 • www.mckinneyhinge.com

All 5K standard weight full mortisewide throw hinges are packed with allmachine and all wood screws.For special screws consult price bookon availability.

Packing:

• NRP(non-removablepin)• RC (roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)•HT(hospital tip)•BT(ball tip)•ST(steeple tip)•SSF(safety stud feature)

• QC(quickconnecthinge)2,4,6,8,10,or 12wire available*

• CC-4(concealedcircuit - 4wire)*availableonhingesup to6 incheswide

• MM(magneticmonitoring)• BeveledEdge(wheredoorsarebeveledonhingesidespecifyTA4398orTA4798)

*QCandCCoptionsavailableonhingesupto6"wide

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experiencedand it is necessary to open the door around a large reveal.

Stainless steel base material polished,plated or furnished in powder coat.

4 x 7 101.6 x 177.8 .130

41⁄2 x 6 114.3 x 152.4 .13441⁄2 x 7 114.3 x 177.8 .134

41⁄2 x 8 114.3 x 203.2 .134

5 x 7 127 x 177.8 .1465 x 8 127 x 203.2 .146

Steel base material polished and platedor furnished in powder coat.

Available Sizes

Inches MM Gauge

TA2398 TA2798

APPLICATION

Available Options:

A5112 StainlessA8112 Steel

ANSI Cross Reference:4 x 7 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 6 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 7 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 8 1⁄2 x 12-24 11⁄4 x 125 x 7 1⁄2 x 12-24 11⁄4 x 12

5 x 8 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 38: Hinge Catalog

McKINNEYHingeCatalogFullMortiseBearingHingesFiveKnuckleHeavyWeight Series

36April2010

©McK

INNEYProductsCom

pany2006-2010

1-800-346-7707 • www.mckinneyhinge.com

All 5K heavy weight full mortise hingesare packed with all machine and allwood screws. For special screws consultprice book on availability.

Packing:

• NRP(non-removablepin)• T4B(ball bearing)• TCA(concealedbearing)• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• HT(hospital tip)• BT(ball tip)• ST(steeple tip)• SSF(safety stud feature)• RB(raisedbarrel)*• QC(ElectroLynxhinge)2, 4, 6, 8, 10or12wire available

• CC(concealedcircuit) 4, 6or8wireavailable**

• MM(magneticmonitoring)• BeveledEdge (wheredoors arebeveledonhinge side specifyT4A4386orT4A4786)

*Refer topage98 for raisedbarrel.

Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other publicbuildings where heavy traffic is experienced.

Steel material polished and plated orfurnished in powder coat.

41⁄2 x 41⁄2 114.3 x 114.3 .180

5 x 41⁄2 127 x 114.3 .180

5 x 5 127 x 127 .190

6 x 5 152.4 x 127 .203

6 x 6* 152.4 x 152.4 .203

8 x 6* 203.2 x 152.4 .203

8 x 8* 203.2 x 203.2 .203

Stainless steel base or available in brassbase material polished and plated orfurnished in powder coat.

Available Sizes

Inches MM Gauge

41⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

5 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

5 x 5 1⁄2 x 12-24 11⁄4 x 12

6 x 5 1⁄2 x 1⁄4-20 11⁄4 x 14

6 x 6 1⁄2 x 1⁄4-20 11⁄2 x 14

8 x 6 1⁄2 x 1⁄4-20 11⁄2 x 14

8 x 8 1⁄2 x 1⁄4-20 11⁄2 x 14

Full Mortise Hinge Fasteners

Inches MM Gauge

T4A3386 T4A3786 Available Options:

A2111 BrassA5111 StainlessA8111 Steel

ANSI Cross Reference:

APPLICATION

Note: 8" x 6" and 8" x 8" have six bearings. Specify T6B3386 / T6B3786

* Supplied in Bronze or Steel only

Page 39: Hinge Catalog

McKINNEYHingeCatalogWideThrowFullMortiseBearingHingesFiveKnuckleHeavyWeight Series

37 June2010

©McK

INNEYProductsCom

pany2006-2010

1-800-346-7707 • www.mckinneyhinge.com

All 5K full mortise heavy duty widethrow hinges are packed with allmachine and all wood screws. Forspecial screws consult price bookon availability.

Packing:

• NRP(non-removablepin)• T4B(ball bearing)• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• HT(hospital tip)• BT(ball tip)• ST(steeple tip)• SSF(safety stud feature)• MM(magneticmonitoring)• BeveledEdge (wheredoors arebeveledonhinge side specifyT4A4386orT4A4786)

Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced.

Stainless steel base material polished,plated or furnished in powder coat.

41⁄2 x 5 114.3 x 127 .18041⁄2 x 6 114.3 x 152.4 .19041⁄2 x 7 114.3 x 177.8 .190

41⁄2 x 8 114.3 x 203.2 .180

5 x 6 127 x 152.4 .190

5 x 7 127 x 177.8 .1905 x 8 127 x 203.2 .190

Steel base material polished and platedor furnished in powder coat.

Available Sizes

Inches MM Gauge

T4A3386 T4A3786 Available Options:

A5111 StainlessA8111 Steel

ANSI Cross Reference:

APPLICATION

41⁄2 x 5 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 6 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 7 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 8 1⁄2 x 12-24 11⁄4 x 125 x 6 1⁄2 x 12-24 11⁄4 x 125 x 7 1⁄2 x 12-24 11⁄4 x 12

5 x 8 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Wide Throw Hinge Fasteners

Hinge Size Machine Wood

Page 40: Hinge Catalog

McKINNEYHingeCatalogSwingClear FullMortiseBearingHingesFiveKnuckle StandardWeight Series (Reversible)

38March

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

All 5K standard weight full mortisehinges are packed with all machineand all wood screws. For special screwsconsult price book on availability. Thepin is held in place by an NRP set screwwhich allows the hinge to be reversible.

Packing:

• TB(ball bearing)• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• HT(hospital tip)• SSF(safety stud feature)• MM(magneticmonitoring)• BeveledEdge (wheredoors arebeveledonhinge side specifyTA4895orTA4395)

Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced. Hinge allows for maximum clearance for passage of beds, tables or other equipment throughdoorway. Pressed steel jambs require no special reinforcing.

Stainless steel material or steel base material polished and plated or furnished inpowder coat.

41⁄2 114.3 .134

Available Sizes

Inches MM Gauge

TA2395 / TA2895 Available Options:

A8122 Steel

ANSI Cross Reference:

APPLICATION

41⁄2 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Swing Clear Hinge Fasteners

Hinge Size Machine Wood

Page 41: Hinge Catalog

McKINNEYHingeCatalogSwingClear FullMortiseBearingHingesFiveKnuckleHeavyWeight Series (Reversible)

39 March

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

All 5K heavy weight full mortise hingesare packed with all machine and allwood screws. For special screws consultprice book on availability. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.

Packing:

• T4B(ball bearing)• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise)

• HT(hospital tip)• SSF(safety stud feature)• MM(magneticmonitoring)• BeveledEdge (wheredoors arebeveledonhinge side specifyT4A4395 orT4A4795)

Recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced. Hinge allows for maximum clearance for passage of beds, tables or other equipment throughdoorway. Pressed steel jambs require no special reinforcing.

Stainless steel material polishedand passivated.

Steel base material polished and platedor furnished in powder coat.

41⁄2 114.3 .1805 127 .190

Available Sizes

Inches MM Gauge

T4A3395 T4A3795 Available Options:

A5121 StainlessA8121 Steel

ANSI Cross Reference:

APPLICATION

41⁄2 1⁄2 x 12-24 11⁄4 x 12

5 1⁄2 x 12-24 11⁄2 x 12

Swing Clear Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 42: Hinge Catalog

McKINNEY Hinge CatalogFull Mortise Steel HingesFive Knuckle Standard Weight Series

40January2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

• NRP(non-removablepin)• Consult the factory for available finishes

Packed 3 each per box, 48 per carton.All machine x all wood screws.

Recommended for standard weight doors. For doors withclosing devices MPB 79, bearing hinge must be used.MacPro by McKINNEY templated hinges are made toconform to ANSI/BHMA 156.1, 156.7.

Plain bearing hinge. Steel base materialpolished and plated or furnished inprime coat.

Bearing hinge. Steel base polished andplated or furnished in prime coatfinish.

MP79 MPB79 Available Options:

A8112 SteelA8133 Steel

ANSI Cross Reference:

Packing:APPLICATION

41⁄2 x 41⁄2 114.3 x 114.3 .134

Available Sizes

Inches MM Gauge

41⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

Swing Clear Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 43: Hinge Catalog

McKINNEY Hinge CatalogFull Mortise Steel HingesFive Knuckle Standard Weight Series

41 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

• NRP(non-removablepin)

Packed 3 each per box, 48 per carton.All machine x all wood screws.

Recommended for standard weight , medium frequency doors,or doors with closing devices. MacPro by McKINNEYtemplated hinges are made to conform to ANSI/BHMA156.1, 156.7.

Bearing hinge. Stainless base polishedto a satin satin finish.

MPB91 Available Options:

• U32D SatinStainless

Available Finishes

A5112 Stainless

ANSI Cross Reference:

Packing:

APPLICATION

41⁄2 x 41⁄2 114.3 x 114.3 .134

Available Sizes

Inches MM Gauge

Page 44: Hinge Catalog

McKINNEY Hinge CatalogFull Mortise Steel HingesFive Knuckle Heavy Weight Series

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

• NRP(non-removablepin)• Consult the factory for available finishes

Packed 3 each per box, 48 per carton.All machine x all wood screws.

Recommended for use on high frequency and or heavy woodor metal doors in schools, hospitals or other public buildingswhere heavy traffic is experienced. MacPro by McKINNEYtemplated hinges are made to conform to ANSI/BHMA156.1, 156.7.

Bearing hinge, stainless steel base,polished to a satin stainless finish.

Bearing hinge. Steel base polished andplated.

MPB99 Available Options:

A5111 StainlessA8111 Steel

ANSI Cross Reference:

Packing:

APPLICATION

41⁄2 x 41⁄2 114.3 x 114.3 .180

Available Sizes

Inches MM Gauge

MPB68

42

Page 45: Hinge Catalog

McKINNEYHingeCatalogStandardDutyCenterHungJambMountPivot Set

43 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Interior or exterior doors up to:• 125 lbs• 3'6" x 8'0"*

Ferrous base pivot set polished and plated.

Recommended for use on average frequency double acting doors in schools,hospitals, institutions and other public buildings. Not for use on labeled doorsand frames.

C07042

EP5-J

Aluminum 31⁄2 lbs 5 lbsWood -Particle Core 5 lbs 53⁄4 lbsWood -Stave Block Core 4 lbs 41⁄2 lbs

14 GaugeHollow Metal 83⁄4 lbs 10 lbs16 GaugeHollow Metal 71⁄2 lbs 81⁄2 lbs18 GaugeHollow Metal 61⁄2 lbs 71⁄2 lbs

Door Weight Chart(lbs per square foot)

Door Thickness13⁄4" 2"

• Thrust steel ball bearing inbottompivot, oil impregnatedbronzebearingin toppivot

• Centerhung• Mortised into side jamb• Fullmortise toppivot• Non-handed• Ferrousmaterial• 15⁄32" radiusheel edgeof door

ANSI Cross Reference

Features:

Maximum Door Weight:

All EP5-JPivot sets arepackedwith14x11⁄2"wood screws and1⁄4-20x5⁄8"machine screws

Packing:

Page 46: Hinge Catalog

McKINNEYHingeCatalogFullMortise InstitutionalHingesMaximumSecurityProtectionSeries

44October

2005

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight full mortiseinstitutional hinges are packed with allTorx Head Security machine screws.For special screws consult price bookon availability.

Packing:

Torx Pin Head Machine 1/2 x 12 - 24Wood Screws supplied by request only1-1/4 x 12 Torx Pin Head

Institutional Hinge Fasteners

• MM(magneticmonitoring)*• BeveledEdge (wheredoors arebeveledonhinge side specify

HTA5386MSP-AorHTA5386MSP-B

*NotavailablewithPSFoption

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where security requirements exist.

Set of three Hospital Tip hingesfeaturing concealed bearing assemblies.The top and bottom hinges arefurnished with Prison Safety Feature(PSF) and Safety Studs (SSF).

The middle hinge is not supplied withPSF or SSF

41⁄2 x 41⁄2 114.3 x 114.3 .1805 x 41⁄2* 127 x 114.3 .190

Set of three Hospital Tip hingesfeaturing concealed bearing assemblies.The top and bottom hinges arefurnished with Prison Safety Feature(PSF) and Safety Studs (SSF) - thethird hinge is furnished with QC8Electrolynx connectors.

The electric hinge is not furnishedwith PSF or SSF

Available Sizes

Inches MM Gauge

HTA386 MSP-A HTA386 MSP-B

PRISON SAFETY FEATURE (PSF)HOSPITAL TIP (HT)

Available Options:

A5111 Stainless

ANSI Cross Reference:

APPLICATION

Page 47: Hinge Catalog

McKINNEYHingeCatalogFullMortiseAnchorHingeSetThreeKnuckleHeavyWeight Series

45 June2010

©McK

INNEYProductsCom

pany2006-2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight full mortiseanchor hinge sets consist of oneanchor hinge and two 5 x 41⁄2 fullmortise hinges. These sets requirehanding and are packed with allmachine and all wood screws. Forspecial screws consult price book onavailability. Because the pin is insertedfrom the bottom of the barrel, it is heldin place by an NRP set screw which isnormally furnished with other hingesonly as an extra cost option. Anchorplate for door header only, permitsuse of holders and closers concealedin the top of the jamb. The screws gointo the door header and are in shearpreventing the hinge from pulling loosefrom the door.

A5551 StainlessA8551 Steel

Packing:

• SSF(safety stud feature)• CC-4(concealedcircuit - 4wire, centerhingeonly)

• QC(ElectroLynxhinge)2, 4, 6, 8, 10or12wire available, centerhingeonly

• CC(concealedcircuit) 4, 6or8wireavailable, centerhingeonly

• MM(magneticmonitoring, centerhingeonly)

• BeveledEdge (wheredoors arebeveledonhinge side specifyTA5391orTA5791)

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.They are designed especially for doors where other hardware (door holders or doorclosers) or abuse places an unusual strain on the door, jamb and hinges.

Stainless steel base material polished,plated or furnished in powder coat.

5 x 41⁄2 127 x 114.3 .190

Available Sizes

Inches MM Gauge

Steel base material polished and platedor furnished in powder coat.

For use with concealed door holders or door closersTA391 TA791

APPLICATION

ANSI Cross Reference

Available Options:

5 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Anchor Hinge Fasteners

Hinge Size Machine Wood

Page 48: Hinge Catalog

McKINNEYHingeCatalogFullMortiseAnchorHingeSetThreeKnuckleHeavyWeight Series

46June2010

©McK

INNEYProductsCom

pany2006-2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight full mortiseanchor hinge sets consist of oneanchor hinge and two 5 x 41⁄2 fullmortise hinges. These sets requirehanding and are packed with allmachine and all wood screws. Forspecial screws consult price book onavailability. Because the pin is insertedfrom the bottom of the barrel, it is heldin place by an NRP set screw which isnormally furnished with other hingesonly as an extra cost option. Anchorplate for jamb and door header permitsuse of surface applied holders andclosers. The screws are in shearpreventing the hinge from pullingloose from either the door or the jamb.

A5551 StainlessA8551 Steel

Packing:

5 x 41⁄2 127 x 114.3 .190

Available Sizes

Inches MM Gauge

• SSF(safety stud feature)• QC(ElectroLynxhinge)2, 4, 6, 8, 10or12wire available, centerhingeonly

• CC(concealedcircuit) 4, 6or8wireavailable, centerhingeonly

• MM(magneticmonitoring, centerhingeonly)

• BeveledEdge (wheredoors arebeveledonhinge side specifyTA5392orTA5792)

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.They are designed especially for doors where other hardware (door holders or doorclosers) or abuse places an unusual strain on the door, jamb and hinges.

Stainless steel base material polished,plated or furnished in powder coat.

Steel base material polished and platedor furnished in powder coat.

For use with surface applied door holders or door closersTA392 TA792

APPLICATION

ANSI Cross Reference

Available Options:

5 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Anchor Hinge Fasteners

Hinge Size Machine Wood

Page 49: Hinge Catalog

McKINNEYHingeCatalogFullMortiseAnchorHingeSetThreeKnuckleHeavyWeight Series

47 June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight full mortiseanchor hinge sets consist of oneanchor hinge and two 5 x 41⁄2 fullmortise hinges. These sets requirehanding and are packed with allmachine and 1⁄2 wood screws. Forspecial screws consult price book onavailability. Because the pin is insertedfrom the bottom of the barrel, it is heldin place by an NRP set screw which isnormally furnished with other hingesonly as an extra cost option. Anchorplate for jamb header only, permits useof holders and closers concealed in thetop of the door. The screws go intothe jamb header and are in shearpreventing the hinge from pullingloose from the jamb.

A5551 StainlessA8551 Steel

Packing:

• SSF(safety stud feature)• QC(ElectroLynxhinge)2, 4, 6, 8, 10or12wire available, centerhingeonly

• CC(concealedcircuit) 4, 6or8wireavailable, centerhingeonly

• MM(magneticmonitoring, centerhingeonly)

• BeveledEdge (wheredoors arebeveledonhinge side specifyTA5393orTA5793)

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.They are designed especially for doors where other hardware (door holders or doorclosers) or abuse places an unusual strain on the door, jamb and hinges.

Stainless steel base material polished,plated or furnished in powder coat.

Steel base material polished and platedor furnished in powder coat.

For use with concealed door holders or door closersTA393 TA793

APPLICATION

ANSI Cross Reference

Available Options:

5 x 41⁄2 127 x 114.3 .190

Available Sizes

Inches MM Gauge

5 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Anchor Hinge Fasteners

Hinge Size Machine Wood

Page 50: Hinge Catalog

McKINNEYHingeCatalogFullMortiseAnchorHingeSetThreeKnuckleHeavyWeight Series

48June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight full mortiseanchor hinge sets consist of oneanchor hinge and two 5 x 41⁄2 fullmortise hinges. These sets requirehanding and are packed with allmachine and 1⁄2 wood screws. Forspecial screws consult price book onavailability. Because the pin is insertedfrom the bottom of the barrel, it is heldin place by an NRP set screw which isnormally furnished with other hingesonly as an extra cost option. Anchorplate for jamb and door header, permitsuse of surface applied holders andclosers. The screws are in shearpreventing the hinge from pulling loosefrom either the jamb or the door.

A5551 StainlessA8551 Steel

Packing:

• SSF(safety stud feature)• CC-4(only)• QC(ElectroLynxhinge)2, 4, 6, 8, 10or12wire available, centerhingeonly

• CC(concealedcircuit) 4, 6or8wireavailable, centerhingeonly

• MM(magneticmonitoring, centerhingeonly)

• BeveledEdge (wheredoors arebeveledonhinge side specifyTA5394orTA5794)

Recommended for use on high frequency and/or heavy wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.They are designed especially for doors where other hardware (door holders or doorclosers) or abuse places an unusual strain on the door, jamb and hinges.

Stainless steel base material polished,plated or furnished in powder coat.

Steel base material polished and platedor furnished in powder coat.

TA394 - 4" DOOR LEG TA794 - 4" DOOR LEG

APPLICATION

ANSI Cross Reference

Available Options:

5 x 41⁄2 127 x 114.3 .190

Available Sizes

Inches MM Gauge

5 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Anchor Hinge Fasteners

Hinge Size Machine Wood

Page 51: Hinge Catalog

McKINNEYHingeCatalogHalfMortisePlainBearingHingesFiveKnuckle StandardWeight Series (Reversible)

49 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All 5K plain bearing standard weighthalf mortise hinges are packed with allmachine screws. For special screwsconsult price book on availability. Thejamb leaf is applied to the surface ofthe jamb with machine screws. Thedoor leaf is mortised into the edge ofthe door. The pin is held in place by anNRP set screw which allows the hingeto be reversible.

A8233 Steel

Packing:

• HT(hospital tip)• BeveledEdge (wheredoors arebeveledonhinge side specifyT4774)

Recommended for use on minimum frequency and/or light weight wood or stockhollow metal doors in residences, apartments or other very low frequency doors incommercial construction. The hinges may be used on channel iron jambs.

Note: Bearing hinges should be used on high and average frequency doors and on all doors equippedwith door closers and/or door holders.

Steel base material polished and plated or furnished in powder coat.

T2774

41⁄2 114.3 .134

Available Sizes

Inches MM Gauge

APPLICATION

ANSI Cross Reference

Available Options:

41⁄2 1⁄2 x 12-24

Half Mortise Hinge Fasteners

Hinge Size Machine

Page 52: Hinge Catalog

McKINNEYHingeCatalogHalfMortiseBearingHingesFiveKnuckle StandardWeight Series (Reversible)

50June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 5K standard weight half mortisehinges are packed with all machinescrews. For special screws consult pricebook on availability. The jamb leaf isapplied to the surface of the jamb withmachine screws. The door leaf ismortised into the edge of the door.The pin is held in place by an NRPset screw which allows the hinge tobe reversible.

A5212 StainlessA8212 Steel

Packing:

• TB(ball bearing)• TCA(concealedbearing)• HT(hospital tip)• BeveledEdge (wheredoors arebeveledonhinge side specifyTA4374orTA4774)

Recommended for use on average frequency and/or medium weight wood or metaldoors in schools, hospitals or other public buildings where medium traffic isexperienced. The hinges may be used on channel iron jambs.

41⁄2 114.3 .1345 127.0 .146

Available Sizes

Inches MM Gauge

Steel base material polished and platedor furnished in powder coat.

TA2774

Stainless steel base material polished,plated or furnished in powder coat.

TA3374

ANSI Cross Reference

Available Options:

APPLICATION

41⁄2 1⁄2 x 12-245 1⁄2 x 12-24

Half Mortise Hinge Fasteners

Hinge Size Machine

Page 53: Hinge Catalog

McKINNEYHingeCatalogHalfMortiseBearingHingesThreeKnuckle StandardWeight Series (Reversible)

51 June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K standard weight half mortisehinges are packed with all machinescrews. For special screws consult pricebook on availability. The jamb leaf isapplied to the surface of the jamb withmachine screws. The door leaf ismortised into the edge of the door. Thepin is held in place by an NRP set screwwhich allows the hinge to be reversible.

A5212 StainlessA8212 Steel

Packing:

Stainless steel base material polished,plated or furnished in powder coat.

• HT(hospital tip)• BeveledEdge (wheredoors arebeveledonhinge side specifyTA5374orTA5774)

Recommended for use on average frequency and/or medium weight wood or metaldoors in schools, hospitals or other public buildings where medium traffic isexperienced. The hinges may be used on channel iron jambs.

Steel base material polished and platedor furnished in powder coat.

TA374 TA774

41⁄2 114.3 .1345 127.0 .146

Available Sizes

Inches MM Gauge

Available Options

ANSI Cross Reference

APPLICATION

41⁄2 1⁄2 x 12-24

5 1⁄2 x 12-24

Half Mortise Hinge Fasteners

Hinge Size Machine

Page 54: Hinge Catalog

McKINNEYHingeCatalogHalfMortiseBearingHingesThreeKnuckleHeavyWeight Series (Reversible)

52June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight half mortisehinges are packed with all machinescrews. For special screws consult pricebook on availability. The jamb leaf isapplied to the surface of the jamb withmachine screws. The door leaf is mortisedinto the edge of the door. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.

Packing:

Stainless steel base material polished,plated or furnished in powder coat.

• HT(hospital tip)• BeveledEdge (wheredoors arebeveledonhinge side specifyTA5384orTA5784)

Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The hinges may be used on channel iron jambs.

41⁄2 114.3 .1805 127.0 .190

6* 152.4 .203

* Advise door thickness 13⁄4" or 21⁄4"

Available Sizes

Inches MM Gauge

Steel base material polished and platedor furnished in powder coat.

TA384 TA784

A5211 StainlessA8211 Steel

ANSI Cross Reference

Available Options

APPLICATION

41⁄2 1⁄2 x 12-245 1⁄2 x 12-246 1⁄2 x 12-24

Half Mortise Hinge Fasteners

Hinge Size Machine

Page 55: Hinge Catalog

McKINNEYHingeCatalogHalfMortiseBearingHingesFiveKnuckleHeavyWeight Series (Reversible)

53 June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 5K heavy weight half mortisehinges are packed with all machinescrews. For special screws consult pricebook on availability. The jamb leaf isapplied to the surface of the jamb withmachine screws. The door leaf is mortisedinto the edge of the door. The pin isheld in place by an NRP set screwwhich allows the hinge to be reversible.

A5211 StainlessA8211 Steel

ANSI Cross Reference

Packing:

Stainless steel base material polished,plated or furnished in powder coat.

• T4B(ball bearing)• TCA(concealedbearing)• HT(hospital tip)• BeveledEdge (wheredoors arebeveledonhinge side specifyT4A4384orT4A4784)

Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The hinges may be used on channel iron jambs.

Steel base material polished and platedor furnished in powder coat.

T4A3384 T4A3784

41⁄2 114.3 .1805 127.0 .190

6* 152.4 .203

* Advise door thickness 13⁄4" or 21⁄4"

Available Sizes

Inches MM Gauge

Available Options

APPLICATION

41⁄2 1⁄2 x 12-245 1⁄2 x 12-24

6 1⁄2 x 12-24

Half Mortise Hinge Fasteners

Hinge Size Machine

Page 56: Hinge Catalog

McKINNEYHingeCatalogSwingClearHalfMortiseBearingHingesThreeKnuckleHeavyWeight Series (Reversible)

54May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All 3K swing clear heavy weight halfmortise hinges are packed with allmachine screws for the door and1⁄2 x 1⁄4-20 machine screws for thejamb leaf. For special screws consultprice book on availability. The jambleaf is applied to the surface of thejamb with machine screws. The doorleaf is mortised into the edge of thedoor. The pin is held in place by anNRP set screw which allows the hingeto be reversible.

A8221 Steel

ANSI Cross Reference

Packing:

Steel base material polished and plated or furnished in powder coat. • HT(hospital tip)•BeveledEdge (wheredoors arebeveledonhinge side specifyTA5789)

Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The swing of these hinges allows maximum clearance for passage of beds, tablesor other equipment through door openings. These hinges may be used on channeliron frames.

TA789

APPLICATION

5 127.0 .190

Available Sizes

Inches MM Gauge

Available Options

Page 57: Hinge Catalog

McKINNEYHingeCatalogSwingClearHalfMortiseBearingHingesFiveKnuckleHeavyWeight Series (Reversible)

55 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All 5K swing clear heavy weight halfmortise hinges are packed with allmachine and 1⁄2 wood screws for thedoor and 1⁄2 x 1⁄4-20 machine screwsfor the jamb leaf. For special screwsconsult price book on availability. Thejamb leaf is applied to the surface ofthe jamb with machine screws. Thedoor leaf is mortised into the edge ofthe door. The pin is held in place by anNRP set screw which allows the hingeto be reversible.

A8221 Steel

ANSI Cross Reference

Packing:

Steel base material polished and plated or furnished in powder coat. • T4B(ball bearing)• HT(hospital tip)• BeveledEdge (wheredoors arebeveledonhinge side specifyT4A4789)

Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The swing of these hinges allows maximum clearance for passage of beds, tablesor other equipment through door openings. These hinges may be used on channeliron frames.

T4A3789

5 127.0 .190

Available Sizes

Inches MM Gauge

Available Options

APPLICATION

Page 58: Hinge Catalog

McKINNEY Hinge Catalog

56April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

INTENTIONALLYLEFTBLANK

Page 59: Hinge Catalog

McKINNEYHingeCatalogHalf SurfaceBearingHingesThreeKnuckle StandardWeight Series (Reversible)

57 June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

Stainless steel base material polished,plated or furnished in powder coat.

All 3K standard weight half surfacehinges are packed with all machinescrews and 2 x 1⁄4-20 door bolts andgrommet nuts. For special screwsconsult price book on availability. Thejamb leaf is fastened into the mortisewith machine screws. The door leaf isapplied full surface with grommet nutsand bolts. Specify if the door thicknessis greater than 13⁄4" to insure thatproper bolt is packed. The pin is heldin place by an NRP set screw whichallows the hinge to be reversible.

Packing:

• BackPlate (BP-10)*• HT(hospital tip)

*Refer topage85 forBP-10

Recommended for use on frequency and/or medium weight wood or metal doorsin schools, hospitals or other public buildings where medium traffic is experienced.

Steel base material polished and platedor furnished in powder coat.

TA372 TA772

41⁄2 114.3 .1345 127.0 .146

Available Sizes

Inches MM Gauge

APPLICATION

A5212 StainlessA8212 Steel

ANSI Cross Reference

Available Options

Page 60: Hinge Catalog

McKINNEYHingeCatalogHalf SurfaceBearingHingesThreeKnuckleHeavyWeight Series (Reversible)

58June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 3K heavy weight half surface hingesare packed with all machine screws and2 x 1/4-20 door bolts and grommet nuts.For special screws consult price bookon availability. The jamb leaf is fastenedinto the mortise with machine screws.The door leaf is applied full surfacegrommet nuts and bolts. Specify if thedoor thickness is greater than 13⁄4" toinsure that proper bolt is packed. Thepin is held in place by an NRP setscrew which allows the hinge to bereversible.

Packing:

Stainless steel base material polished,plated or furnished in powder coat.

• BackPlate (BP-10)*• HT(hospital tip)

*Refer topage85 forBP-10

Recommended for use on frequency and/or heavy weight wood or metal doors inschools, hospitals or other public buildings where heavy traffic is experienced.

Steel base material polished and platedor furnished in powder coat.

41⁄2 114.3 .1805 127.0 .1906 152.4 .203*

A5411 StainlessA8411 Steel

ANSI Cross Reference

Available Options

APPLICATION

TA382 TA782

* Not available in Stainless Steel

Available Sizes

Inches MM Gauge

Page 61: Hinge Catalog

McKINNEYHingeCatalogHalf SurfacePlainBearingHingesFiveKnuckle StandardWeight Series (Reversible)

59 June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 5K plain bearing standard weighthalf surface hinges are packed with allmachine screws and 2 x 1⁄4-20 doorbolts and grommet nuts. For specialscrews consult price book onavailability. The jamb leaf is fastenedinto the mortise with machine screws.The door leaf is applied full surfacewith grommet nuts and bolts. Specify ifthe door thickness is greater than 13⁄4"to insure that proper bolt is packed.The pin is held in place by an NRP setscrew which allows the hinge to bereversible.

Packing:

• BackPlate (BP-10)*• HT(hospital tip)

*Refer topage85 forBP-10

Steel base material polished and plated or furnished in powder coat.

41⁄2 114.3 .134

Available Sizes

Inches MM Gauge

Recommended for use on minimum frequency and/or light weight wood or stockhollow metal doors in residences, apartments or other very low frequency doors incommercial construction. The hinges may be used on channel iron jambs.

Note: Bearing hinges should be used on high and average frequency doors andon all doors equipped with door closers and/or door holders.

A8433 Steel

ANSI Cross Reference

Available Options

APPLICATION

T2772

Page 62: Hinge Catalog

McKINNEYHingeCatalogHalf SurfaceBearingHingesFiveKnuckle StandardWeight Series (Reversible)

60May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All 5K standard weight half surfacehinges are packed with all machinescrews and 2 x 1⁄4-20 door bolts andgrommet nuts. For special screwsconsult price book on availability. Thejamb leaf is fastened into the mortisewith machine screws. The door leaf isapplied full surface with grommet nutsand bolts. Specify if the door thicknessis greater than 13⁄4" to insure thatproper bolt is packed. The pin is heldin place by an NRP set screw whichallows the hinge to be reversible.

Packing:

Stainless steel base material polished,plated or furnished in powder coat.

• BackPlate (BP-10)*• TB(ball bearing)• TCA(concealedbearing)• HT(hospital tip)

*Refer topage85 forBP-10

Recommended for use on average frequency and/or medium weight wood or metaldoors in schools, hospitals or other public buildings where medium traffic isexperienced.

Steel base material polished and platedor furnished in prime or powder coat.

TA2372 TA2772

41⁄2 114.3 .1345 127.0 .146

Available Sizes

Inches MM Gauge

A5412 StainlessA8412 Steel

ANSI Cross Reference

Available Options

APPLICATION

Page 63: Hinge Catalog

McKINNEYHingeCatalogHalf SurfaceBearingHingesFiveKnuckleHeavyWeight Series (Reversible)

61 Junw2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

All 5K standard weight half surfacehinges are packed with all machinescrews and 2 x 1⁄4-20 door bolts andgrommet nuts. For special screws consultprice book on availability. The jambleaf is fastened into the mortise withmachine screws. The door leaf is appliedfull surface with grommet nuts andbolts. Specify if the door thickness isgreater than 13⁄4" to insure that properbolt is packed. The pin is held in placeby an NRP set screw which allows thehinge to be reversible.

Packing:

Stainless steel base material polished,plated or furnished in powder coat.

• BackPlate (BP-10)*• TB(ball bearing)• TCA(concealedbearing)• HT(hospital tip)

*Refer topage85 forBP-10

Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.

Steel base material polished and platedor furnished in powder coat.

T4A3382 T4A3782

41⁄2 114.3 .1805 127.0 .1906* 152.4 .203

* Not available in Stainless Steel or TCA

Available Sizes

Inches MM Gauge

A5411 StainlessA8411 Steel

ANSI Cross Reference

Available Options

APPLICATION

Page 64: Hinge Catalog

McKINNEYHingeCatalogSwingClearHalf SurfaceBearingHingesThreeKnuckleHeavyWeight Series (Reversible)

62June2010

©McK

INNEYProductsCom

pany2006-2010

1-800-346-7707 • www.mckinneyhinge.com

Steel base material polished and plated or furnished in powder coat. • HT(hospital tip)

All 3K swing clear heavy weight halfsurface hinges are packed with allmachine screws and 2 x 1/4-20 doorbolts and grommet nuts. For specialscrews consult price book onavailability. The jamb leaf is fastenedinto the mortise with machine screws.The door leaf is applied full surfacewith grommet nuts and bolts. Specifyif the door thickness is greater than1 3/4" to insure that proper bolt ispacked. The pin is held in place by anNRP set screw which allows the hingeto be reversible.

Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The swing of these hinges allows maximum clearance for passage of beds, tables orother equipment through door openings.

TA796

APPLICATION

5 127.0 .190

Available Sizes

Inches MM Gauge

A8421 Steel

ANSI Cross Reference

Available Options

Packing:

Page 65: Hinge Catalog

McKINNEYHingeCatalogSwingClearHalf SurfaceBearingHingesFiveKnuckleHeavyWeight Series (Reversible)

63 June2010

©McK

INNEYProductsCom

pany2006-2010

1-800-346-7707 • www.mckinneyhinge.com

Steel base material polished and plated or furnished in powder coat. • T4B(ball bearing)• HT(hospital tip)

All 5K swing clear heavy weight halfsurface hinges are packed with allmachine screws and 2 x 1/4-20 doorbolts and grommet nuts. For specialscrews consult price book onavailability. The jamb leaf is fastenedinto the mortise with machine screws.The door leaf is applied full surfacewith grommet nuts and bolts. Specifyif the door thickness is greater than1 3/4" to insure that proper bolt ispacked. The pin is held in place by anNRP set screw which allows the hingeto be reversible.

Recommended for use on high frequency and/or heavy weight wood or metal doorsin schools, hospitals or other public buildings where heavy traffic is experienced.The swing of these hinges allows maximum clearance for passage of beds, tables orother equipment through door openings.

T4A3796

5 127.0 .190

Available Sizes

Inches MM Gauge

A8421 Steel

ANSI Cross Reference

Available Options

Packing:APPLICATION

Page 66: Hinge Catalog

McKINNEY Hinge Catalog

64April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

INTENTIONALLYLEFTBLANK

Page 67: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceBearingHingesThreeKnuckleHeavyWeight Series

65 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

A2311 BronzeA5311 StainlessA8311 Steel

ANSI Cross Reference

Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inpowder coat.

The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x12-24)* screws and the door leaf isapplied to the surface of the door withwood screws or grommet nuts and bolts(2x1⁄4-20). Specify door thickness ifgreater than 13⁄4".

• HT(hospital tip)

Recommended for use on high frequency and/or heavy weight wood or Kalameindoors in schools, hospitals or other public buildings where medium traffic prevails.The hinges may be used on channel iron frames.

Steel base material polished and platedor furnished in powder coat.

TA381 TA781

41⁄2 114.3 .1345 127.0 .146

Available Sizes

Inches MM Gauge

Available Options

APPLICATION

Page 68: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceBearingHingesFiveKnuckleHeavyWeight Series

66April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

A2311 BronzeA5311 StainlessA8311 Steel

ANSI Cross Reference

Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inpowder coat.

The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x12-24)* screws and the door leaf isapplied to the surface of the door withwood screws or grommet nuts and bolts(2x1⁄4-20). Specify door thickness ifgreater than 13⁄4".

* (1⁄2x1⁄4-20 provided on 6")

• T4B(ball bearing)• TCA(concealedbearing)• HT(hospital tip)

Recommended for use on high frequency and/or heavy weight wood or Kalameindoors in schools, hospitals or other public buildings where medium traffic prevails.The hinges may be used on channel iron frames.

Steel base material polished and platedor furnished in powder coat.

T4A3381 T4A3781

41⁄2 114.3 .1345 127.0 .146

6* 152.4 .203

* Not available in Stainless Steel

Available Sizes

Inches MM Gauge

Available Options

APPLICATION

Page 69: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceBearingHingesThreeKnuckle StandardWeight Series

67 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

A8312 Steel

ANSI Cross Reference

Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inpowder coat.

The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x12-24) screws and the door leaf isapplied to the surface of the door withwood screws or grommet nuts and bolts(2x1⁄4-20). Specify door thickness ifgreater than 13⁄4".

• HT(hospital tip)

Recommended for use on standard weight and/or medium frequency doors inschools, hospitals or other public buildings where medium traffic prevails. Thehinges may be used on channel iron frames.

Steel base material polished and platedor furnished in powder coat.

TA371 TA771

41⁄2 114.3 .1345 127.0 .146

Available Sizes

Inches MM Gauge

Available Options

APPLICATION

Page 70: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceBearingHingesFiveKnuckle StandardWeight Series

68May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

A8312 Steel

ANSI Cross Reference

Stainless steel base material polishedand passivated or Bronze base materialpolished and plated or furnished inpowder coat.

The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x12-24) screws and the door leaf isapplied to the surface of the door withwood screws or grommet nuts and bolts(2x1⁄4-20). Specify door thickness ifgreater than 13⁄4".

• TB(ball bearing)• TCA(concealedbearing)• HT(hospital tip)

On standard weight and/or medium frequency doors in schools, hospitals or otherpublic buildings where medium traffic prevails. The hinges may be used on channeliron frames.

Steel base material polished and platedor furnished in powder coat.

TA2371 TA2771

41⁄2 114.3 .1345 127.0 .146

Available Sizes

Inches MM Gauge

Available Options

APPLICATION

Page 71: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceSwingClearBearingHingesThreeKnuckleHeavyWeight Series

69 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

A8321 Steel

ANSI Cross Reference

The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x1⁄4-20) screws and the door leaf isapplied to the surface of the door withwood screws (1x1⁄4-14) or grommetnuts and bolts (2x1⁄4-20). Specify doorthickness if greater than 13⁄4".

• HT(hospital tip)

High frequency and/or heavy weight wood or Kalamein doors in hospitals or otherinstitutions where heavy traffic prevails. This hinge allows for the maximumclearance for passage of beds, tables and other equipment through the doorway.

Steel base material polished and plated or furnished in powder coat.

TA797

5 127.0 .190

Available Sizes

Inches MM Gauge

Available Options

APPLICATION

Page 72: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceSwingClearBearingHingesFiveKnuckleHeavyWeight Series

70Jnue2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

A8321 Steel

ANSI Cross Reference

The narrow leaf is applied to thesurface of the jamb with machine(1⁄2x1⁄4-20) screws and the door leaf isapplied to the surface of the door withwood screws (1x1⁄4-14) or grommetnuts and bolts (2x1⁄4-20). Specify doorthickness if greater than 13⁄4".

• T4B(ball bearing)• HT(hospital tip)

Frequency and/or heavy weight wood or Kalamein doors in hospitals or otherinstitutions where heavy traffic prevails. This hinge allows for the maximumclearance for passage of beds, tables and other equipment through the doorway.

Steel base material polished and plated or furnished in powder coat.

T4A3797

5 127.0 .190

Available Sizes

Inches MM Gauge

Available Options

APPLICATION

Discontinued

Page 73: Hinge Catalog

McKINNEYHingeCatalogFullMortise SingleActingStandardWeight SpringHinge

71 September

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

All 1502 and 1552 series standardweight single acting spring hingesare packed with all machine and allwood screws. For special screws consultprice book on availability. This non-handed hinge series has infiniteadjustment and tension can be addedor reduced by means of a hex keywhich is provided. Locking screwprovides tamper-resistance after theproper tension has been set. Forunparalled tamper resistance andsecurity choose our TRS option. Twonylon tee bearings for vertical andlateral loads. Coil spring providesclosing power.

Packing:

• RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise

• HT(hospital tip - onone sideonly*)• ReverseSpringOption1502-R*(Maintains thedoor intheopenposition)

• TRS(tamper resistantoption) foradditional security.A tamper resistantscrew is screwed into the tension ratchetafter theproper tensionhasbeen set.

*Voids theUL® listing

Recommended for standard weight, medium frequency doors in place of doorclosers in apartments, hotels, motels, office buildings, etc.

Caution: Use of gasket for smoke or sound protection, wind condition ofunbalanced air pressure may prevent door from latching. Additional closingpower would be required. NFPA requires a minimum of two (2) spring hingeson labeled doors.

K81071 SteelK81071F SteelK51071 Stainless SteelK51071F Stainless Steel

ANSI Cross Reference

Available Options

APPLICATION

1502 1552

C USLISTED

Steel basematerial polishedandplatedorfurnished inpowder coat.

Stainless steelmaterial polishedandpassivated.

4 x 4 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

4 x 4* 101.6 x 101.6 .13041⁄2 x 4 114.3 x 101.6 .13441⁄2 x 41⁄2 114.3 x 114.3 .134

Available Sizes

Inches MM Gauge

Page 74: Hinge Catalog

McKINNEYHingeCatalogFullMortise SingleActingStandardWeight SpringHingeSet

72March

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

All 1522 sets of standard weight singleacting spring hinges are furnished withtwo 1502 and one 1500 (spring-less)hinge with all machine and all woodscrews. For special screws consult pricebook on availability. This non-handedhinge series has infinite adjustmentand tension can be added or reducedby means of a hex key which isprovided. Locking screw providesunparalleled tamper-resistance after theproper tension has been set. Two nylontee bearings for vertical and lateralloads. Coil spring provides closingpower. The two spring hinges should belocated as the top and center hinge.The "dummy" or spring-less hingeshould be located as the bottom hinge.

Packing:

Steel base material polished and plated or furnished in prime or powder coat finish. • RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise

• HT(hospital tip - onone sideonly*)• MM(magneticmonitoring)

*Voids theUL® listing

Recommended for standard weight, medium frequency doors in place of doorclosers in apartments, hotels, motels, office buildings, etc.

Caution: Use of gasket for smoke or sound protection, wind condition ofunbalanced air pressure may prevent door from latching. Additional closingpower would be required. NFPA requires a minimum of two (2) spring hingeson labeled doors.

1522

4 x 4 101.6 x 101.6 .130

41⁄2 x 4 114.3 x 101.6 .13441⁄2 x 41⁄2 114.3 x 114.3 .134

Available Sizes

Inches MM Gauge

K81071 SteelK81071F Steel

ANSI Cross Reference

Available Options

APPLICATION

C US

LISTED

4 x 4 1⁄2 x 12-24 11⁄4 x 12

41⁄2 x 4 1⁄2 x 12-24 11⁄4 x 1241⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

Full Mortise Hinge Fasteners

Hinge Size Machine Wood

Page 75: Hinge Catalog

McKINNEYHingeCatalogHalf SurfaceSingleActingStandardWeight SpringHinge

73 March

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

All 1572 Series Standard Weight SingleActing Spring Hinges are packed withall machine and all wood screws. Forspecial screws consult price book onavailability. This non-handed hingeseries has infinite adjustment andtension can be added or reduced bymeans of a hex key which is provided.Locking screw provides unparalleledtamper-resistance after the propertension has been set. Two nylon teebearings for vertical and lateral loads.Coil spring provides closing power.

Packing:

Steel base material polished and plated or furnished in powder coat finish. • RC(roundcorner - 1⁄4" radius furnishedunless specifiedotherwise

• HT(hospital tip - onone sideonly*)• MM(magneticmonitoring)

*Voids theUL® listing

Recommended for standard weight, medium frequency doors in place of doorclosers in apartments, hotels, motels, office buildings, etc.

Caution: Use of gasket for smoke or sound protection, wind condition ofunbalanced air pressure may prevent door from latching. Additional closingpower would be required. NFPA requires a minimum of two (2) spring hingeson labeled doors.

1572

41⁄2 x 41⁄2 114.3 x 114.3 .134

Available Sizes

Inches MM Gauge

K81081 SteelK81081F Steel

ANSI Cross Reference

Available Options

APPLICATION

C US

LISTED

41⁄2 1⁄2 x 12-24

Half Mortise Hinge Fasteners

Hinge Size Machine

Page 76: Hinge Catalog

McKINNEYHingeCatalogHeavyDutyDoubleActingSpringButtHinge

74April2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Specification ScheduleMaximum Door Thickness 13⁄4" 13⁄4"

# of Hinges for Each Door 2 3

Maximum Door Width 3’0" 4’0"

Door Height* 8 to 9’ 8 to 9’

Maximum Door Weight 265 320

The application is simplified andmore secure by fastening the jambflange directly to the jamb without ahanging strip. The door flange ismortised into the door. If desired thejamb flange may be applied to thesurface of the jamb with a mortise inthe door sufficient to receive thethickness of both flanges. Thisapplication eliminates a filler strip andis used frequently on channel ironframes. This hinge is packed withhexagonal head bolts and nuts for theclamp flange and machine screws forthe jamb flange.

K61091 Cast Iron

ANSI Cross Reference

• Due to itsheavyconstruction, theCS1 isuseful inpreventingdooroscillations inextremeandvariabledraft conditions

• Heavycastmalleable ironwith twoaxis’swhichpermit thedoor toopen180˚

• Hingepins are securelyheld inplacebyaset screw

• Spring is protected fromdamage insidetheall castmalleable construction

• Door and frame shouldbepreppedusingthe installation instructionsprovidedwith theunit

Features:

When estimating the weight ofdoors, be sure to include (with theexception of hinges) all hardware,metal plates and buffers. For hollowmetal doors or wood doors over 3' widewith heavy metal plates, we recommendthree hinges for each door to avoidpossible sagging. The third hingeshould be placed near the top hinge butallow space for pin removal. The use ofHi-Duty Spring Steel Buffers will inmost installations protect the doorwithout use of heavy metal plates. Thiswill reduce the weight of the door andload on the hinges. Spring Steel Buffersillustrated on next page.

For replacement spring, orderH15 Spring.

Recommended for use on high frequency and/or heavy wood or metal trucking doorsin post offices, warehouses or other buildings where heavy traffic is experienced.

APPLICATION

* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.

Cast malleable iron furnished in PC (Prime Powder Coat) or AP or D4 finish.

CS1

These hinges are not intended forpedestrian traffic. They are for use ontrucking doors

Page 77: Hinge Catalog

McKINNEYHingeCatalogFullMortise SingleActingAdjustable SpringHinge

75 July2009

©McK

INNEYProductsCom

pany2009

1-800-346-7707 • www.mckinneyhinge.com

• P(powderprime), andUS26D• MPS679 - SetofTwoMPS60 springhinges andoneMPB79 fullmortisebutthinge

Packed 3 each per box, 48 per carton.All machine x all wood screws.

Recommended for standard weight hinge applicationsrequiring self-closing control, such as apartments, hotels,motels, dormitories, office buildings, etc.

MacPro by McKINNEY templated hinges are made toconform to ANSI/BHMA 156.1, 156.7, 156.17

Steel base material polished and plated or furnished in prime coat.

MPS60 Available Options:

A8112 SteelA8133 Steel

ANSI Cross Reference:

Packing:APPLICATION

41⁄2 x 41⁄2 114.3 x 114.3 .134

Available Sizes

Inches MM Gauge

41⁄2 x 41⁄2 1⁄2 x 12-24 11⁄4 x 12

Swing Clear Full Mortise Hinge Fasteners

Hinge Size Machine Wood

C US

LISTED

Page 78: Hinge Catalog

McKINNEYHingeCatalogHeavyDutyAdjustableTensionSimplexFull SurfaceDoubleActingDoorSpring

76April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

450 SERIES

K87441 Steel

ANSI Cross Reference

• Coil springsmadeofhighgrade steelwire• Adjustabletension,nospecialtoolsrequired• Wrought steel brackets preventbreakage• Economical• Simplifiedmethodof closingdoors

Features:

All 450 Series are finished in 1D(black) and are packed with 1x12wood screws. This economical series isdesigned to be surface applied to thedoor and frame.

Dimensions

Number 451 452 453

Overall Length 9" 11" 13"

Spring Length 5" 7" 9"

Packing:

Page 79: Hinge Catalog

McKINNEYHingeCatalogSimplexFullMortiseDoubleActingSpringButt-Hinge

77 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All 1001 Series Double Acting SpringHinges are packed all wood screws.This hinge is designed to be applieddirectly to the jamb without the use ofa hanging strip. Door flange requires ashallow mortise.

Packing:

1001

K81041 Steel

ANSI Cross Reference

• Forwooddoorsnotweightedwithplateglass orheavyhardware

• Door flangemortised indoor• JambFlangeSurface applied to theframe face

• Non-templated (sizes 3", 4", 5", 6")• Springs aremadeofhighgradetempered steel

• Non-handed

Features:

It is recommended that three hinges be used on door sizes as indicated above.The center hinge should be installed as close as possible to the top hinge for maximum support.

Steel base material polished and plated or furnished in prime coat finish.

Approximate Dimensions in InchesA Length of Door Flange

(size of hinge) 3 4 5 6

B Minimum Thickness of Door 3⁄4 7⁄8 11⁄8 11⁄4C Maximum Thickness of Door

with Chamfering 1 11⁄4 11⁄2 13⁄4

D Maximum Thickness of Doorwithout Chamfering for Metal Doors 7⁄8 11⁄8 13⁄8 13⁄4

Door SpecificationsMinimum 3⁄4" x 2’2" to 7⁄8" x 2’2" to 11⁄8" x 2’4" to 11⁄4" x 2’6" toMaximum 1" x 2'0" 11⁄4" x 2’0" 11⁄2" x 2’2" 13⁄4" x 2’4"

Maximum Door Sizes and Weights2 Hinges Per Door 3 Hinges Per Door

Catalog Number Door Weight Lbs. Door Width Door Weight Lbs. Door Width Door Height*

1001 3" 35 2’0" 40 2’8" 5’0"

1001 4" 60 2’4" 75 3’0" 6’8"

1001 5" 65 2’8" 93 3’0’ 6’8"

1001 6" 75 2’8" 107 3’0" 7’0"

* Minimum height for weights shown. Hinge capacity decreases as door height decreases.Refer to 6x4-1/2 1001 for 1-3/4" thick stock hollow metal doors .

APPLICATION

Page 80: Hinge Catalog

McKINNEYHingeCatalogSimplexFullMortiseDoubleActingSpringButt-Hinge

78April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

APPLICATION

All 6x41⁄2"1001 Series Double ActingSpring Hinges are packed all machine x1⁄2 wood screws. This hinge is designedto be applied directly to the jambwithout the use of a hanging strip.Door flange requires a shallow mortise.

Packing:

K81151 Steel

ANSI Cross Reference

1001 6 X 41⁄2

• For stockhollowmetal orwooddoorsthat are13⁄4" thick

• Door flangedesigned to fit standard41⁄2x41⁄2" templatemortise

• JambFlangeSurface applied to theframe face

• Springs aremadeofhighgradetempered steel

• Non-handed

Features:

It is recommended that three hinges be used on door sizes as indicated above.These listed weights include a margin of safety. Minimum clearance required onedge of door and frame on lock side. Hinge side clearance, allow 1⁄4" per doorbecause of jamb flange and hinge body not being mortised. The center hingeshould be installed as close as possible to the top hinge for maximum support.Hinge capacity decreases as door height decreases.

Steel base material polished and plated or furnished in prime coat finish.

Specification Schedule for Door 7’ High or MoreMax Door Weight* Lockside Clearance*

Door Width 2 Each 3 Each Flat Edge Round Edge

2’0" 96 145 1⁄4" 1⁄16"

2’2" 89 135 3⁄16" 1⁄16"

2’6" 77 125 3⁄16" 1⁄16"

2’8" 72 115 1⁄8"1⁄16"

3’0" 64 105 1⁄8"1⁄16"

*Minimum height for weights shown. Hinge capacity decreases as door height decreases.

Page 81: Hinge Catalog

McKINNEYHingeCatalogSimplexFullMortiseDoubleActingSpringButt-Hinge

79 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

APPLICATION

9001

K81041 Steel

ANSI Cross Reference

• Forwoodormetal doors ofheavyconstruction.Note: For stockhollowmetal doors, use6x41⁄2 1001

• JambFlangeSurface applied to theframe face

• Springs aremadeofhighgradetempered steel

• Non-handed

Features:

It is recommended that three hinges be used on door sizes as indicated above.The center hinge should be installed as close as possible to the top hinge formaximum support.

All 9001 Series Double Acting SpringHinges are packed all machine x 1⁄2wood screws. For special screws consultprice book on availability. This hinge isdesigned to be applied directly to thejamb without the use of a hangingstrip. Door flange requires a deepermortise than a 1001.

Steel base material polished and plated or furnished in prime coat finish.

Specifications for 8" 9001Door Weight Door Width # Hinges/Door

103 3’6" 2

143 4’0" 3

11⁄2" to 2" Door Thickness7’0" Door Height*

* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.

Packing:

Page 82: Hinge Catalog

McKINNEYHingeCatalogSimplexDoubleActingClampFlangeSpringButt-Hinge

80April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

19001

K81111 Steel

ANSI Cross Reference

• Designed foruseon trucking doorways• Springs aremadeofhighgradetempered steel

• Channels are spotweldedand riveted toflange for additional strength

Features:

If doors are extra heavy, we recommend three hinges per door. The third hingeshould be installed as close as possible to the top hinge as conditions will permit formaximum support. For doors subjected to severe shock, we recommend the CS1Spring Hinge.

All 19001 Series Double Acting SpringHinges are packed with Hex Headthrough bolts, nuts and all woodscrews. The clamp flange is attached tothe door surface with through bolts forgreater security of fastenings.

Steel base material polished and plated or furnished in prime coat finish.

Specifications for 8" 19001Door Weight Door Width # Hinges/Door

100 3’6" 2

140 4’0" 3

Minimum 31⁄2" Door Style Width7’0" Door Height*

* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.

APPLICATION Packing:

Page 83: Hinge Catalog

McKINNEYHingeCatalogSimplexHalf SurfaceDoubleActingSpringButt-Hinge

81 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

HS1001

K81131 Steel

ANSI Cross Reference

• For thinplywooddoors or gateswherescrewswill nothold inedgeof door

• Doesnot require ahanging strip• Non-Templated (sizes 3", 4")• Springs aremadeofhighgradetempered steel

• Non-handed

Features:

It is recommended that three hinges be used on door sizes as indicated above.The center hinge should be installed as close as possible to the top hinge formaximum support.

All Half Surface 1001 Series DoubleActing Spring Hinges are packed withall wood screws. This hinge is designedfor one flange to be applied to thesurface of door and other to the surfaceof jamb.

Steel base material polished and plated or furnished in prime coat finish.

Specifications for 3" HS1001Door Weight Door Width # Hinges/Door

35 2’0" 2

38 2’8" 33⁄4" to 1" Door Thickness5'0" Door Height*

* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.

Specifications for 4" HS1001Door Weight Door Width # Hinges/Door

60 2’8" 2

75 3’0" 37⁄8 to 11⁄4" Door Thickness6'8" Door Height*

* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.

APPLICATION Packing:

Page 84: Hinge Catalog

McKINNEYHingeCatalogAjaxDoubleActingHorizontal SpringPivotHinge

82August2004

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Furnished painted or in finely plated finish.

This hinge is equipped with a 90˚ hold open feature, hardened steel roller bearingsand slotted screws that hold in the floor plate to permit easy alignment. It also hasadjustable tension and nylon top pivot and socket.

Application of attaching plate and hinge to the bottom of door is very simple andrequires only a rectangular mortise cut.

3001-STEEL / J3001-STEEL

• Foruseonhollowmetal orwooddoorsin residences, restaurants andotherpublicplaces

• Anti FrictionBearing• Adjustable spring tension• NonHanded• Optional jambattachingplate forconcreteor tile floor (toorder, prefix “J”tonumber)

Features:

Specifications for 3001Door Thickness 11⁄8" to 13⁄4"

Door Weight 90

Door Width 3'0"

Page 85: Hinge Catalog

McKINNEYHingeCatalogSaglessDoubleActingGateSpringPivotHinge

83 May

2007

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Furnished painted or in finelyplated finish.

Has an exterior tension adjustmentwhich can be adjusted after hinge isapplied. Anti-friction bearing tocarry the weight of the gate and ananti-friction bearing in the top socketwhich reduces friction and wear. Thepintle has an adjustment in the bottom

attachment with a locking devicewhich permits aligning the gate orsetting the gate in desired position.Spring is large enough for heavy dutyconditions but the adjustable tensionmakes it equally suited for light gates.

The 4007 RB Series attachmentsare applied to the surface of the frameand the box is applied to the bottom

surface of the gate. However, in the4007MRB Series, the box is mortisedinto the bottom of the gate.

Specify MRB for mortised box andreversed brackets; specify RB forreverse brackets only.

Before ordering, please noteclearances in chart.

4007RB-MALLEABLE IRON 4007MRB-MALLEABLE IRON

• Foruseonwood andmetal gates• Exterior tensionadjustment• Anti-frictionbearings• Pintle adjustmentwith lockingdevice

Features:

Catalog # 4007MRB 4007RB

Minimum Clearance Under Gate 23⁄8" 4"

Gate or Handrail Thickness 11⁄8 -21⁄2" 11⁄8 -21⁄2"

Weight of Gate 75 75

Width of Gate 3'0" 3'0"

Width of Jamb Attachment 11⁄4" 11⁄4"

* Minimum height for weights shown. Hinge capacitydecreases as door height decreases.

Clearances

Page 86: Hinge Catalog

McKINNEYHingeCatalogLightweightDoubleActingGravityPivotHinge

84April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Furnished painted or in finelyplated finish.

The 8007 features a unique ballbearing pivot riding on a hardenedsteel cam providing frictionless longlasting service. The H8007 is similar tothe 8007 except that it has a 90˚ holdopen feature in either direction.

Attachments are surface applied tothe jamb and the top socket may besurface applied or mortised into the topof the door. The box may be surfaceapplied or mortised into the bottom ofthe door.

8007-STEEL / H8007-STEEL

• Foruseondouble actingwoodLouvredoors 3⁄4" to13⁄4" thickwhichdonotexceed18" inwidth, 5' inheightor40lbs inweight

Features:

Door Thickness 3⁄4" to 13⁄4"

Door Weight 40

Door Width 1'6"

Door Height* 5'0"

* Maximum height for weights shown. Hinge capacitydecreases as gate height decreases.

Specifications for 8007/H8007

Page 87: Hinge Catalog

McKINNEYHingeCatalogHingeBackPlate

85 June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

Furnished painted or in finely plated finish.

BP-10 for T2772 / TA2772 / T4A3782

Above shown with 4-hole pattern for 5" BP-103-hole pattern provided for 4½" BP-105-hole staggered pattern provided for 6" BP-10

BP-11 for T4A3796

BP-12 for 1572

Page 88: Hinge Catalog

McKINNEYHingeCatalogCombinationStrike andStop

86March

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

CSS-9

All Combination Strike and Stops arepacked with 1⁄2 x 8-32 machine screws.

.095 gauge brass material polished and plated. Manufactured for use withcylindrical or bored locks.

• Available inoffsetorcenterhung latchboltlocation for framesizes53⁄4", 57⁄8" and63⁄4"

• Foruseon1-3⁄4" thickdoors• Customunits available for framesizes31⁄2" -91⁄2"- consult the factory foravailability

Features:

Packing:

Recommended for installations on hospital or nursing home toilet doors alongwith our EP5-J. This unit allows center hung or 1⁄8" inset doors to be opened inboth directions without damaging the frame.

APPLICATION

OFFSET HUNG CENTER HUNG

Cannot be used with deadbolts. May not work with mortise locks.Consult the factory for mortise lock application of CORBIN RUSSWIN,SARGENT and YALE compatability.

Page 89: Hinge Catalog

McKINNEYHingeCatalogEmergencyDoorStop

87 March

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

Bronze material polished and plated, rubber bumper insert encased in high impactABS plastic case.

DS-6

APPLICATION

Recommended for installation with our EP-5J pivot in schools, hospitals,institutions and other public buildings. This unit allows center hung or1⁄8" inset doors to be opened in both directions without damaging the frame.

All Stops are packed with 1⁄2 x 12-24machine screws.

• Used toconvert double actingdoorshungoncenterpivots to single actingdoors

• Emergency release allowsdoor to swingopen in theoppositedirection

• Mortiseonlyon frame• Latch releaseswitha touchof the finger• Second touchof lever returns latch tooriginal position

Features:

A1882 Bronze

ANSI Cross Reference

Specifications for DS-6

Size of Surface Plate 41⁄2" x 15⁄8"

Bolt Length 2"

Size of Case 21⁄8" x 15⁄16"

Packing:

Page 90: Hinge Catalog

McKINNEYHingeCatalogDoubleLippedStrike

88March

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

All Double Lipped Strikes are packedwith 1⁄2 x 8-32 machine screws.

.095 gauge brass material polished and plated. Manufactured for use withcylindrical or bored locks.

Packing:

DLS-8

Recommended for installations on hospital or nursing home toilet doors alongwith our EP5-J and DS-6 Emergency Stop. This unit allows center hung or1⁄8" inset doors to be opened in both directions without damaging the frame.

• Available inoffset or centerhung• Latchbolt location for frame sizes 53⁄4"and63⁄4"

• Foruseon1-3⁄4" thickdoors• Customunits available for frame sizes31⁄2" - 91⁄2"- consult the factory foravailability

Features:

APPLICATION

Center Hung Shown

Cannot be used with deadbolts. May not work with mortise locks.Consult the factory for mortise lock application of CORBIN RUSSWIN,SARGENT and YALE compatability.

Page 91: Hinge Catalog

McKINNEY Hinge CatalogElectroLynx Hinge (QC Option)

89 July2008

Copyright©2007-2008,McK

inneyProductsCom

pany,an

ASSAABLO

YGroup

company.Allrightsreserved.

Reproductioninwholeorinpartwithouttheexpress

writtenpermission

ofMcK

inneyProductsCom

panyisprohibited.

1-800-346-7707 • www.mckinneyhinge.com

The McKinney ElectroLynx Hingeis an intermediate connector whichpasses a constant flow of currentbetween the source of power (jamb)and the actuated devices in the door(i.e. electric locks, exit devices, etc.)regardless of door position.Each hinge features concealed plug

connectors which eliminate the needfor separate or exposed wiring. Brasseyelets add protection and durability tothe ElectroLynx Hinge and commonwire colors and standard connectorsmake installation quick and simple.The ElectroLynx Hinge should be

installed in the center position on thedoor. Once installed, it will give nooutward indication of its function andwill transmit power efficiently andreliably, as long as the wire capacity isnot exceeded.

All ElectroLynx Electric Hinges arefactory tested and specially packaged tominimize against damage duringshipment. Installation instructions arepacked with each hinge.28 Gauge multi-strand wires are

used. A 6" pigtail is provided forconnection to the source wiring. Thewire colors are coordinated to workwith other ASSA ABLOY Companieselectro-mechanical hardware.An 8 position connector is used for

QC2, QC4, QC6 and QC8 wirehinges. An 8 position and 4 positionconnector is used for QC12 wirehinges. A QC2A wire hinge isavailable for power on, poweroff applications.Electrolynx pigtails are included

with electrified aluminum continuoushinges as a standard.

QC

• Availableup to12wires• Rated4AmpCapacity• CanbeusedwithMMoptiononmost5-knuckle fullmortisehinges*

• OptionalMG-16mortar guardavailable(mortar guard requiredon steel frames)

• QC2wirehingesprovidedwith8positionconnector fornewconstruction ,specifyQC2

*Refer to individual catalogpages regardingtheavailability of theseoptions

Features:

UNDERWRITERSLABORATORYLISTED

APPLICATION

Page 92: Hinge Catalog

McKINNEYHingeCatalogConcealedCircuitElectricHinge (CCOption)

90July2008

Copyright©2007-2008,McK

inneyProductsCom

pany,an

ASSAABLO

YGroup

company.Allrightsreserved.

Reproductioninwholeorinpartwithouttheexpress

writtenpermission

ofMcK

inneyProductsCom

panyisprohibited.

1-800-346-7707 • www.mckinneyhinge.com

The McKINNEY Concealed CircuitHinge is an intermediate connectorwhich passes a constant flow of currentbetween the source of power (jamb)and the actuated devices in the door(i.e. electric locks, exit devices, etc.)regardless of door position.The color of the wires assists in

maintaining proper circuit hookupbetween the power source and actuateddevices during installation.CC Electric Hinges should be

installed in the center position on thedoor. Once installed, it will give nooutward indication of its function andwill transmit power efficiently andreliably, as long as the wire electricalcapacity is not exceeded.

All CC Electric Hinges are factorytested and specially packaged to insureagainst damage during shipment.Installation instructions are packedwith each hinge.28 gauge multi-strand wire with 12"

long leeds is used. It is recommendedthat care be exercised during connectionof the leads and installation of thehinge to avoid wire damage.The CC feature is available on most

two, three and five knuckle full mortisecontract grade hinges. Consult theindividual catalog pages for thisoption feature.

CC

• Availablewith2,3or4circuits• 4Amp,24Voltsmaximumeachcircuitcontinuousduty,16.0Amps intermittentduty (pulse) for300milliseconds

• Canbeused inconjunctionwithMMoptiononmost fullmortisehinges

• OptionalmortarguardMG-16available• Electric featureundetectablewhenhingeis installed

Features:

4 Wires 2 Circuits

6 Wires 3 Circuits

8 Wires 4 Circuits

UNDERWRITERSLABORATORYLISTED

APPLICATION

REAR VIEW

Wire Capacity

Page 93: Hinge Catalog

McKINNEYHingeCatalogAluminumContinuousElectrifiedHinge(SER&ACCOptions)

91 Decem

ber

2009

©McK

INNEYProductsCom

pany2006-2009

1-800-346-7707 • www.mckinneyhinge.com

The McKINNEY electrified continuous hinge is furnished with bonded, 4- conductorflat cable with connectors at each leaf. Each 4 or 8 conductor cable is able to carry4 amps @ 24 volts with a 16 amp in-rush current for 300 milliseconds. To protectthe cable from any overload or surge in power, each hinge is supplied with a 4 ampin-line fuse. And a wire harness is supplied with each hinge as a standard.*

Two options allow variable degrees of service to be performed at the specificlocation of the current carrying cables via either a removable 8" or a pivoting 8"section of the hinge. Both of these options, SER and ACC are available as QC4, 8or 12 wire configurations on our Full Mortise Aluminum Continuous Hinges.

SER & ACC OPTIONS

• Performance tested1,250,000cycleswiththe4conductor flat cable

• Each4-conductorcablecarries4amps@24voltswitha16ampinrushcurrent for300milliseconds

• Eachhinge isprovidedwitha4ampin-linefuse toprotect thecable fromanyoverloador surge inpower

• Flatcableconductor iswarranted5years• AvailableonFullMortiseAluminumContinuousHinges

• ElectricalmodificationmeetsnewSDIlocationatcenterofhinge

Features:

The hinge is furnished to be installedin three sections, allowing the currentcarrying cables to be serviced orreplaced without removing the doorfrom the frame.

Additionally the SER option allowsthe current carrying cables to be safelystored or delivered to the electricianor security contractor prior to theinstallation of the electrified hardware,eliminating the necessity of theelectrician or security contractor beingpresent when the doors are being hung.Product Number Example:83"MCK25HD CL x –SER-8*

*hinges are handed

SERVICEABLE/REMOVABLE (SER)

The hinge is furnished to be installedin a single section with leafs modifiedto pivot at the location of the currentcarrying cables and allow access to thecables and connected wiring. Electricalmodification is in the center of the hinge.

Product Number Example:83"MCK25HD CL x ACC-8*

*hinges are handed

ACCESSIBLE (ACC)

Product Number Example: 83"MCK25HD CL x -SER

Concealed Magnetic Monitoring (CM) is also available with theSER and ACC options.Product Numbering Example: MCK25HD-83C x CM-SER

MCK25HD-83C x CM-ACC

Flat cable connector is warranted for five years. Failure to install the 4 amp in-line fuse voids the warranty

ACC is the same leaf components witha single piece (full length) gear cap...and is accessible/non-removable.

SER Option Shown

*Each 4 and 8 wire electrical prep is supplied with a 48" and 96" wire harnessand an Elextrolynx connector. Each 12 wire hinge is supplied with a 15'cable for frame side. Additional wire harness or Electrolynx connector mustbe specified when ordering a 12 wire hinge.

Page 94: Hinge Catalog

McKINNEYHingeCatalogMagneticMonitoringHinge (MMOption)

92September

2009

©McK

INNEYProductsCom

pany2006,2007,2009

1-800-346-7707 • www.mckinneyhinge.com

• Switch isU.L.Listedat6V- .25amps;12V- .25amps;24V- .125amps;48V- .062amps

• For lowvoltage(48voltmaximum).25AMPACorDCnon-inductive load

• Monitoring featureundetectablewhenhinge is installed

• Magnetic reedconcealed switch impervioustodirt andmoisture

• 12" leads suppliedas standard(extra lengthsavailable)

• NarrowStile (NS)SwitchandWideGapMagnetoptionsavailable

• Canbeused inconjunctionwithQC optiononmost fullmortisehingesupto QC12

• Canbeused inconjunctionwithCCoptiononmost fullmortisehingesup toCC8Wire

The McKINNEY Magnetic MonitoringHinge is the only system on the marketthat permits field replacement ofmagnet and switch. It is a simple,dependable system which defiesdetection, yet is readily accessible forinspection and easy adjustment.

MM Electric Hinges should beinstalled in the center position ondoors with three hinges or the secondhinge position from the bottom ondoors with four hinges. Neither switchnor operating magnet are attached to

the hinge. Non-attachment featurereduces the chance of damage duringinstallation. Installation instructionspacked with each hinge.

All MM Electric Hinges areindividually factory pre-tested.

The MM feature is available onmost two, three and five knuckle fullmortise standard and heavy weighthinges, and our full mortise aluminumcontinuous hinges. Consult theindividual catalog pages for this optionfeature.

MM Features:

REAR VIEW

6 V .25 Amps

12 V .25 Amps

24 V .125 Amps

48 V .062 Amps

UNDERWRITERSLABORATORYLISTED

APPLICATION

FRONT VIEW

U.L. Listing

Page 95: Hinge Catalog

McKINNEYHingeCatalogJunctionBox forElectricHinges

93 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

20 gauge galvanized sheet steel, furnished in 2C finish.

MG-16

Recommended for use with our Concealed Circuit and Concealed Switch Hingesto protect wires. Unit to be installed in middle hinge location.

• Knock-outholesonbothends forwires topass through

• Removablecoverplate fromendbrackets• Guard suppliedassembled forusewithelectrichinges

• Fitshinge reinforcements for41⁄2"or5"contactgradehinges

Features:

Page 96: Hinge Catalog

McKINNEYHingeCatalogFullMortisePocketPivotHinge

94April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Investment cast steel base materialpolished and plated or furnished inprime or powder coat finish.

The Full Mortise Pocket PivotHinge is designed to give a flushappearance to the corridor when thedoor is open and recessed into a pocketin the corridor wall.

For single and cross corridor doors,the PH-4 allows the door to lay againstthe wall with no projection into theopening and no gap between the doorand frame.

When combined with a floorcloser, this application has minimumvisible hardware and clearances.

The PH-4 Full Mortise PocketPivot Hinge meets material andperformance requirements of NFPA-80and ANSI A-156-1

PH-4

All Pocket Pivot Hinges are packedwith all machine and all wood screws.

• Twothrustbearings forvertical loads• Rollerbearing for lateral support• Listed forbothhollowmetalor steelcoveredcomposite firedoors ratedupto3hours

• Listed forwoodcore type firedoorsrated20minutes

• .187Gauge• Non-handed

Features:

Recommended for applications where Swing Clear Hinges are aestheticallyunacceptable and use of the full width of the corridor is required, such as crosscorridor and smoke and fire doors as well as patient room doors.

Specifications# of HingesRequired Maximum Door WeightPer Door Door Size (lbs)

2 3'0" x 7'0" 150

3 3'0" x 7'0" 250

4 4'0" x 7'0" 350

Packing:Meets or exceedsANSI A117.1 - 1986Providing Accessibilityand Usability forPhysicallyHandicapped People

APPLICATION

C US

LISTED

Page 97: Hinge Catalog

McKINNEYHingeCatalogStandardWeightLoosePinHinges

95 April2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

SpecificationsSize Size of

(Inches) Gauge Wood Screws

31⁄2 x 31⁄2 .123 7⁄8" x 9

4 x 4 .130 1 x 12

703 STEEL

• Foruseondoorwaysofvery lowfrequencyandmediumweight in industrial application

• Hingesarealsoavailableblank(withoutholes) forwelding

• Available inplain steelwithbrasspins• Fullmortiseonbothdoorsand jambs• Plain steel furnished less screws; zincplatedhinges furnishedwithallwoodscrews

Features:

Discontinued

Page 98: Hinge Catalog

McKINNEYHingeCatalogFullMortiseFiveKnucklePlainBearingLightWeightHinges

96May

2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

Steel based material planished andplated or powder coated or bonderizedand primed for paint.

1400 - Square Corner1414 - 1⁄4" Radius1458 - 5⁄8" - 5⁄8" Radius

Available SizesInches MM Gauge

31⁄2 x 31⁄2 88.90 x 88.90 .099

4 x 4 101.60 x 101.60 .099

• Fullmortiseonbothdoorsand jambs• Suppliedwithallwoodscrewsas standard• Machine screwsavailableby specialorder

Features:

Recommended for use on light weight, low frequency doors hung in wood jambs inresidential construction.

1/4" Radius Shown

1400 / 1414 / 1458

Note: The plated finish on this non-contract grade hinge may not matchthat of an architectural grade hinge.

31⁄2" x 31⁄2" 4 x 4 Staggered HolePattern

Templated hole pattern is no longer available

31⁄2 x 31⁄2 3/4 x 9

4 x 4 1 x 9

WoodSize of Hinge Screws

Residential Hinge Fasteners

Page 99: Hinge Catalog

McKINNEYHingeCatalogOliveKnuckleFullMortiseStandardWeightBearingHinge

97 June2004

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

• Designed forunusualdecorativeeffectsinceonlyoliveknuckle isvisiblewhendoorclosed

• Permanentlyattachedanti-frictionbearingcarriesvertical load

• Non-removable stainless steelpin• Fullmortiseonhollowmetalorwooddoorsand frames

• Handedhinge

Features:

Brass casting polished and/or plated.

TA3383

Recommended for use where doors are of average weight and average frequency,such as fine residential and commercial buildings such as offices, restaurants,hotels/motels or other public buildings where an architecturally pleasingappearance is desired.

SizeInches MM Gauge

6 152.40 .203

All TA3383 Olive Knuckle Hinges arepacked with all machine (1⁄2" x 12-24)and all wood screws (11⁄4" x 12).

Packing:APPLICATION

Discontinued

Page 100: Hinge Catalog

McKINNEYHingeCatalogRaisedBarrelFullMortiseStandardandHeavyWeightHinges

98September

2009

©McK

INNEYProductsCom

pany2006,2007,2009

1-800-346-7707 • www.mckinneyhinge.com

Standard weight hinges for square edgedoors supplied with no hole in bottomplug, side-view McKINNEY stenciland NRP feature are reversible forhanding. Specify RB-TA4714 /RB-TA4314 for doors beveled onhinge side.

Heavy weight hinges for square edgedoors. Specify RB-T4A4786 orRB-T4A4386 for doors beveled onhinge side.

All Raised Barrel Hinges are packedwith all machine x 1⁄2 wood screws.

Packing:

• Door leafmortised intodoor• Frame leafmaybemortisedorsurface applied

• Fullmortiseonhollowmetalorwooddoorsand frames

• Reversiblehinge

Features:RB-TA2714 / RB-TA2314 RB-T4A3786 / RB-T4A3386

Standard weight recommended for use on average frequency and/or medium weight wood or metal doors in schools, hospitalsor other public buildings where medium traffic is experienced.

Heavy weight recommended for use on high frequency and/or heavy wood or metal doors in schools, hospitals or other publicbuildings where heavy traffic is experienced.

Specification Schedule

Standard Wt Heavy Wt

Size (Inches) 41⁄2" x 41⁄2" 41⁄2" x 41⁄2"

Size (MM) 114.30 x 114.30 114.30 x 114.30

Gauge .134 .180

SQUARE EDGE BEVELED EDGE

Page 101: Hinge Catalog

McKINNEYHingeCatalogSlip-InFullMortiseType I andType IIStandardWeightBearingHinges

99 January2004

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All Slip-In Hinges are packed with allmachine x 1⁄2 wood screws.

Packing:

• Non-removable stainless steelpin• Handedhinge• Both leaves specially swaged toprovide

5⁄16" clearancewhen leavesareparallel

Features:

TA-TB2314 Slip-In Brass, Bronze or Stainless Steel. TA-TB2714 Slip-In Steel.

TYPE I TA-TB2314 / TA-TB2714 TYPE II TA-TB2314 / TA-TB2714

Recommended for use on average frequency and/or medium weight aluminumdoors with aluminum frames in schools, hospitals and other public buildings wheremedium traffic is experienced.

One leaf has standard punching andcountersinking and the other leaf isdrilled and tapped so it can be insertedthrough a slot in the door frame.Both leaves are specially swaged toprovide 3⁄16" clearance between leaveswhen parallel.

Both leaves are drilled and tapped sothey can be inserted through a slot inthe door and frame. Both leaves arespecially swaged to provide 5⁄16"clearance between the leaveswhen parallel.

TYPE 1 TYPE 2

Available SizesInches MM Gauge

4 x 4 101.60 x 101.60 .130

41⁄2 x 4 124.30 x 101.60 .134

41⁄2 x 41⁄2 124.30 x 124.30 .134

Type I Hinges Handed - Indicate HandWhen Ordering

RH Shown, LH Opposite

Page 102: Hinge Catalog

McKINNEYHingeCatalogFullMortise InterimHinges

100April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All Interim Hinges are packed with allmachine x 1⁄2 wood screws.

When ordering, specify which is thedoor leaf and which is the jamb leafdimension.

Packing:

• Fornewor retrofit installationswhere thedoorand frameareprepared fordifferent sizehinge leaves

• Available inboth standard(TA2714;TA2314)andheavyweight (T4A3786;T4A3386)

• Hingesarehanded

Features:INTERIM HINGE

Specifications

Door Leaf Jamb Leaf

5" 41⁄2" trimmed to height*

41⁄2" 4" trimmed to height*

Specifications

Jamb Leaf Door Leaf

5" 41⁄2" trimmed to height*

41⁄2" 4" trimmed to height*

Recommended for installations where door and frame are prepped for two differentsize hinges.

*An equal amount is trimmed from the top and bottom of the leaf. For custom trimming, consultthe factory.

Page 103: Hinge Catalog

McKINNEYHingeCatalogContinuousGearedAluminumHinge

101 February2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Performance testing has shown that1,250,000 cycles can be achieved usingour exclusive bonded 4 conductor flatcable which is capable of carrying 4 amps@ 24 volts with a 16 amp in rush currentfor 300 milliamps. The electrical prep isprovided with a 4 amp in-line fuse toprotect the cable from any overload orsurge in power. Installing the hingewithout the fuse will void the warranty(5 year warranty on electrified hinges).

The standard Concealed Current(Option QC) electrically modifiedhinges are supplied with Flat plugconnectors at each leaf, with 4, 8 or 12wires at each leaf and two 6" pigtailsfor use with ElectroLynx® doors andhardware supplied by other ASSA ABLOYcompanies. In addition, these hinges arepackaged with a 36" and a 72" wireharnesses with connector on one endand leads for hard wiring on opposite end.

Our new Serviceable, SER andAccessible, ACC versions (refer tocatalog page 91) come furnished withthe hardware noted above. The SERversion is supplied in three separatesections which allow for the door to beinstalled and the 8" electrical sectioncan be installed at a later time. TheACC version is supplied as a singlehinge with leafs modified to pivot at thelocation of the current carrying cables.This allows for access to cables andconnected wiring.

Power Transfer Cut OutsPT & EPT Preps are available. A prepform must accompany your order andindicate handing, dimension from topof hinge to PT location, etc.

PT for: Adams Rite, Securitron, Yale,Centurion, Dorma

EPT for: Von Duprin

Magnetic Monitoring Hinge(MM Suffix) is available alone or withthe CC option. Refer to catalog page90 for additional information on ourMM function.

PRODUCT INFORMATION ELECTRICAL MODIFICATIONS

Two full-height, paired and geared leavesmanufactured of extruded 6063-T6aluminum Alloy / temper with pinlessassembly that distribute load stressuniformly along the full length of thedoor and frame.

To reduce wear, the frame and door leafare independently machined and thenanodized. This allows the machinedaluminum surfaces that are in directcontact with the bearing to have asmoother, harder surface.

The continuous hinge acts asreinforcement for both door and frame.Special hinge reinforcements are notrequired. However door and framemanufacturers standard is acceptableand removal of hinge reinforcements inthe door and frame is not advised.

The patented chemical composition andinjection process used to produce ourbearings provides for a stronger moreaccurately formed bearing whicheliminates premature wear, guaranteesproper alignment, and requires fewerbearings to carry more weight. And theintermeshing gear segments in the hingenow provide 50% more bearing surface,which results in less wear.

The gear design ensures identicaloperation of each leaf. This allows forvery little effort required in openingheavy commercial grade doors.

These hinges are Guaranteed For TheLife of the Opening (Flat cableconductor or electrically modified hingesare guaranteed for five years). They aretested and certified by UL® (USA &CANADA) to standards UL10B,UL10C and UB7C.2 Part B & BS476(positive pressure) for up to a 3-hour(A-Label) Fire Listing for all 4'0" x 10'0"and 8'0" x 10'0” door and frameassemblies.

These hinges have been cycle testedusing a 150 lb. door and are nowcertified fully functional after 1.5 millioncycles. Per ANSI / BHMA StandardA156.26-2000, these hinges conform to:Grade 2-150 (150# Door @ 1,500,000 cycles)Grade 1-300 (300# Door @ 1,000,000 cycles)Grade 2-300 (300# Door @ 500,000 cycles)Grade 1-600 (600# Door @ 500,000 cycles)

Fire Rating3 hours- hollow metal doors*90 minutes- wood fire doors

FirePins™

are required only for 3 Hour (A Label)Assemblies see page B for additionalinformation

Mounting Hardware To preventwarping of the door along the hingejamb, screws are located along the fulllength of the hinge.

These hinges are ideal for use on centerhung lead lined door

CYCLE REQUIREMENTS

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

Heavier weight can be carried. Contactthe factory at 800-346-7707 forapplications and those not listed in theabove chart

C US

LISTED

Classified and Listed to meet therequirements of Standards, UL10B,UL10C, UBC7-2, Part 1 & BS476POSITIVE PRESSURE

LISTEDDoor Hinges

Page 104: Hinge Catalog

McKINNEYHingeCatalogContinuousGearedAluminumHinge

102February2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

OTHER AVAILABLE OPTIONS DRILL SIZE CHART

Options may require handing. Refer toindividual catalog pages for availability

DD Dutch Door PrepHT Hospital TipCustom length, indicate handing andlength in inches

FirePins™ Kit

1. Frame Portion all fasteners are12-24 x 7/16" Type C, FH U/C threadforming screws• 20 Screws are required per each leaf• Wood Screws available on requestand should be specified on order

• 1/2 x 12-24 Torx Pin Head MachineScrews available on request

2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"• 4 Required per hinge• Shoulder Bolt 1/4-20 x 1" PCH• 4 Required per hinge• Pan Head Self Drilling # 12 x 3/4• 6 Required per hinge

HALF –SURFACE HINGES

EDGE HUNG HINGES

1. Fasteners are # 12-24 x 7/16" Type C,FH U/C thread-forming screws• 20 Screws are required per each leaf• Wood Screws available on requestand should be specified on order

• 1/2 x 12-24 Torx Pin HeadMachine Screws available on request

FULL –SURFACE HINGES

1. Frame Portion all fasteners are12-24 x 7/16" Type C, FH U/C threadforming screws• 12 Screws are required for frame leaf–Wood Screws available on request.

• 1/2 x 12-24 Torx Pin Head MachineScrews available on request

2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"

– 4 Required per hinge• Shoulder Bolt 1/4-20 x 1" PCH

– 4 Required per hinge• Pan Head Self Drilling # 12 x 3/4

– 6 Required per hinge

12HD, 14HD, 22HD, WTHD,25HD, 28HD & 54HD

Material Thickness Drill Size

Aluminum .090 - .140 13

Metal 20 Gauge 17

Metal 16-18 Gauge 15

Metal 12-14 Gauge 13

Wood N/A 5/32"

58HD

1/4-20 Screws

Aluminum .090 - .140 7

Metal 12 – 16 Gauge 7

Metal 18 – 20 Gauge 9

CL Clear anodized aluminumBZ Dark anodized aluminumG Gold anodized aluminumBL Black anodized aluminumSN Brushed satin nickel anodized

aluminum

Consult the factory for availability ofcustom colors on complete hinges or gearcaps only.

FINISHES

HINGE INSTALLATION

The top of the hinge should be installedflush with the top of the door leaf

Installation instructions are packed witheach hinge.

6'8" 79" 20067'0" 83" 2108

7'2" 85" 21598'0" 95" 241310'0" 120" 3048

Available Sizes

Door Size Hinge Length Hinge Length MM

– 79", 83", 85" 95" and 120" lengths arestandard for nominal door heights. Thehinges may be ordered in custom lengths,specify handing and length in inches.

– These hinges may also be cut in thefield. If the hinge must be shortened, cutthe bottom only using a chop saw. Thiswill allow material chips to work outafter the installation. Although thehinge is typically not handed, it becomeshanded after cutting and the cut edgemust be installed at the bottom.

Page 105: Hinge Catalog

McKINNEYHingeCatalogContinuousGearedAluminumHinge

103 February2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Security, Safety, Privacy, Ease of Maintenance• Eliminates alignment problems, such as door sag and binding. Our continuoushinge distributes load stress uniformly along the full length of the door and frame.

• Our inter-meshing gear design, which provides 50% more bearing surface, ensuresless wear and identical operation of each leaf, therefore, very little effort isrequired to open heavy commercial grade doors

• Screws located along the full length of the hinge prevents warping of the dooralong the hinge jamb

• Our continuous hinge acts as reinforcement for both door and frame

• Anodizing is performed after completing all machining, thus allowing that allaluminum surfaces that are in direct contact with the bearing have a smoother,harder surface, thereby reducing wear

• With our geared construction and full length channel cap, the common gapbetween the door and frame is sealed thereby providing security against prying

• The closing of the gap also protects against pinching fingers in doors in publicareas, especially those where children are present

• Sightproof design of the continuous hinge provides privacy for lavatories,executive offices, file rooms etc.

• Superior hinge design and bearings eliminate premature wear, guarantee properalignment and require fewer bearings to carry more weight. This is why we canguarantee our hinge for the Life Of the Opening*

• Our QC, Serviceable and Accessible Options make connecting a Snap!

* Hinges with electrical modifications carry a five year warranty from date of shipment

Why Choose a McKINNEY Continuous Geared Aluminum Hinge?McKINNEY commercial grade hinges consist of two full-heights paired and geared leaves. Each geared leaf rotates evenly formtop to bottom riding on Delrin® -Teflon® bearings. The geared leaves and bearings are held together by a full-length channel cap.This assembly retains the smooth, clean lines of the door and frame while easily supporting heavy vertical loads.

Page 106: Hinge Catalog

McKINNEYHingeCatalogAluminumContinuousGearHingeClearanceDimensions

104October

2005

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

The full-mortise units are designed mainly for new doors and frames, and are applied so as to conceal both leaves. In retrofitapplications, the door width must be reduced for proper clearance (See Figures 1, 2, 3 and 4 below for proper clearance).The full-surface units are designed mainly for retrofit work, and are applied to the exposed surface of the door and frame(See Figures 1 & 2 below for proper clearance).The half-surface units are designed mainly for retrofit applications. The door leaf is applied to the exposed surface of the door,and the frame leaf is applied to the concealed surface of the frame rabbet (See Figures 1 & 2 below for proper clearance).

* Allow extra clearance as required per astragal manufacturer

Full Mortise5/16"

Full Surface0 to 1/8"

Half Surface1/8"

ALL 1/8"

ALL 1/8"

Full Mortise5/16"

Full Surface0 to 1/8"

Half Surface1/8"

ALL 1/8"

ALL1/8" to3/16"

Full Mortise5/16"

Full Surface0 to 1/8"

Half Surface1/8"

Figure 1 – Figure 2 –

Full Mortise / Raised GearWide Throw (w/SquareEdge Door) 5/16"Wide Throw (w/Beveled 3/8"Edge DoorResidential 1-3/4"Raised Gear w/Beveled Edge Door 11/32"Full Mortise Safety 9/16"(w/Square Edge Door)Full Mortise Safety 5/8"(w/Beveled Edge Door)

ALL 1/8"

ALL 1/8"

Figure 3 –

Full Mortise / Raised GearWide Throw (w/SquareEdge Door) 5/16"Wide Throw (w/Beveled 3/8"Edge DoorResidential 1-3/4" 1/4"Full Mortise Safety(w/Square Edge Door) 9/16"Full Mortise Safety(w/Beveled Edge Door) 5/8"Raised Gear 11/32"(w/Beveled Edge Door)

ALL 1/8"

Figure 4 –

Full Mortise / Raised GearWide Throw (w/Square

5/16" Edge Door)3/8" Wide Throw (w/Beveled

Edge Door1/4" Residential 1-3/4"

9/16" Full Mortise Safety(w/Square Edge Door)

5/8" Full Mortise Safety (w/Beveled Edge Door)11/32" Raised Gear (w/Beveled Edge Door)

Page 107: Hinge Catalog

McKINNEYHingeCatalogContinuousAluminumHingeFireRatings

105 February2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

All Hinges designated with these symbols on our catalog pages are tested and certified by Underwriters Laboratories Inc®

(U.S.A. & Canada) to standards UL10B, UL10C (negative pressure) and UBC7.2 Part 1, & BS476 (positive pressure) for up toa 3-Hour (A Label) Fire Listing for all 4'0" x 10'0" and 8'0" x 10'0" door and frame assemblies. Fire listing certifications applyto all approved hollow metal and wood door assemblies in drywall or masonry wall construction. Our Intumescent FirePins™ areonly required on 3-Hour (A Label) assemblies.

Template Screw Locations •

1,500,000 Cycle Test w/150# Door By U.L. Certified Independent La •

UL10B Listed (Negative Pressure), UBC 7.2 (Positive Pressure) •

UL C Listed (Canada) •

Rated 20 min WD x HM Drywall •

Rated 20 min HM x HM Drywall •

Rated 20 min WD x HM Masonry •

Rated 20 min HM x HM Masonry •

Rated 30 min WD x HM Drywall (Canada) •

Rated 30 min HM x HM Drywall (Canada) •

Rated 30 min WD x HM Masonry (Canada) •

Rated 30 min HM x HM Masonry (Canada) •

Rated 45 min WD x HM Drywall •

Rated 45 min HM x HM Drywall •

Rated 45 min WD x HM Masonry •

Rated 45 min HM x HM Masonry •

Rated 60 min WD x HM Drywall •

Rated 60 min HM x HM Drywall •

Rated 60 min WD x HM Masonry •

Rated 60 min HM x HM Masonry •

Rated 90 min WD x HM (16 ga) Drywall •

Rated 90 min WD x HM (16 ga) Masonry •

Rated 90 min WD x HM (18 ga) Drywall •

Rated 90 min WD x HM (18 ga) Masonry •

Rated 90 min HM (20 ga) x HM (18 ga) Drywall •

Rated 90 min HM (20 ga) x HM (18 ga) Masonry •

Rated 90 min HM (20 ga) x HM (16 ga) Drywall •

Rated 90 min HM (20 ga) x HM (16 ga) Masonry •

Rated 90 min HM (18 ga) x HM (18 ga) Drywall •

Rated 90 min HM (18 ga) x HM (18 ga) Masonry •

Rated 90 min HM (18 ga) x HM (16 ga) Drywall •

Rated 90 min HM (18 ga) x HM (16 ga) Masonry •

Rated 90 min HM (16 ga) x HM (16 ga) Drywall •

Rated 90 min HM (16 ga) x HM (16 ga) Masonry •

Rated 90 min HM (16 ga Vert. Stiff) x HM (16 ga) Drywall •

Rated 90 min HM (16 ga Vert. Stiff) x HM (16 ga) Masonry •

Rated 3 Hour HM x HM Masonry/Drywall

Retrofit Applications - Fire Rated •

Maximum Rated Opening Size - Pair 8'0" Wide x 10' high •

Cut to Size in Field •

Indicates FirePins™ Required

� �� �

� �

LISTEDDoor Hinges

Page 108: Hinge Catalog

McKINNEYHingeCatalogContinuousGearedAluminumHingeFirePins™

106October

2005

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

FirePin™ Locations• The locations illustrated belowindicate where holes should be drilledon the hinge edge of the door

• These locations are appropriate for allhinge models (edge hung, full-surface,and half surface)

FirePin™ Locations for Use With Fire Rated Assemblies• Although McKINNEY Continuous Geared Hinges carry UL Fire Ratingsunequaled in the industry, some applications may require the use of FirePins™.Please refer to the Fire Label Ratings Chart (page CG-5) for informationregarding their use.

• FirePin™ applications fall within the UL guidelines for retrofitting assemblies inthe field. Expensive shop modifications and door/frame reinforcements are notrequired.

• FirePins™ also add extra security to a door assembly.

r

LISTEDDoor Hinges

d

Page 109: Hinge Catalog

McKINNEYHingeCatalogFullMortise -EdgeHungFlushDoorContinuousGearHinge

107 February2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

Electrical Modifications (Suffix)All electrically modified hinges arefurnished with our 4 conductor flat cableconnectors at each leaf and two pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harness withconnectors on one end and hard wiringon opposite end. A 4 amp fuse issupplied to protect the cable fromoverload or surge in power. Failure toinstall the fuse voids the warranty.

• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in thedoor QC-4; QC-8; QC-12

• Serviceable – Same as QC except hingesupplied in three sections with 8"electrically modified leaf.SER-4; SER-8; SER-12*

• Accessible – Same as QC exceptfurnished with a pivoting 8” section.ACC-4; ACC-8; ACC-12

• MM – Magnetic Monitoring

• PT - Power transfer Prep (cut out only)For Adams Rite, Securitron, Yale,Dorma & Centurion*

• EPT – Power transfer prep (cut outonly) For Von Duprin*

*PT or EPT Location Form mustaccompany your order

Refer to catalog Pages 88-90 additionalinformation on our electrical options.

Extruded 6063-T6 aluminumalloy/temper with pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

MCK-12HD SERIES

STANDARD APPLICATION

The MCK-12HD Series is designed foruse with doors that are standard 1-3/4"up to 2-1/4" thick.

–Designed for use on retrofitapplications and allows for adjustmentin order to properly align the lock edgeof the door to the frame.

Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.

Mounting Hardware # 12-24 x 7/16"FHUC, Type C, thread-forming. 20required for each leaf. Wood screwsavailable on request only.

For Kawneer Tuffline Series, specifythe prefix “K”, for instance 83" KMCK-12HD –Designed for use with bi-foldapplications to keep the faces of thedoors flush.

Kawneer Tuffline Series Application

The McKINNEY MCK-12HD continuousgear hinges are recommended for newconstruction and renovations includingnew door and frame, new door withexisting frame or existing door withnew frame.

These hinges are GUARANTEEDFOR THE LIFE OF THE OPENING

The flat cable conductor or electricallymodified hinges are guaranteed forfive years.

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

OPTIONAL FEATURES

LISTEDDoor Hinges

Page 110: Hinge Catalog

McKINNEY Hinge CatalogFull Mortise - Edge Hung Flush DoorContinuous Gear Hinge

September

2009

©McK

INNEYProductsCom

pany2009

1-800-346-7707 • www.mckinneyhinge.com

G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

Electrical Modifications (Suffix)All electrically modified hinges arefurnished with our 4 conductor flat cableconnectors at each leaf and two pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harness withconnectors on one end and hard wiringon opposite end. A 4 amp fuse issupplied to protect the cable fromoverload or surge in power. Failure toinstall the fuse voids the warranty.

• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in thedoor QC-4; QC-8; QC-12

• Serviceable – Same as QC except hingesupplied in three sections with 8"electrically modified leaf.SER-4; SER-8; SER-12*

• Accessible – Same as QC exceptfurnished with a pivoting 8” section.ACC-4; ACC-8; ACC-12

• MM – Magnetic Monitoring

• PT - Power transfer Prep (cut out only)For Adams Rite, Securitron, Yale,Dorma & Centurion*

• EPT – Power transfer prep (cut outonly) For Von Duprin*

*PT or EPT Location Form mustaccompany your order

Refer to catalog Pages 88-90 additionalinformation on our electrical options.

Extruded 6063-T6 aluminumalloy/temper with pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

K-MCK-12HD SERIES

The K-MCK-12HD Series is designedfor Kawneer Tufflline® Series, 2" deepdoors with a door style option forcontinuous hinges.

Special hinge reinforcements are notrequired. Kawneer Tuffline® Series metaldoor and frame standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.

Mounting Hardware # 12-24 x 7/16"FHUC, Type C, thread-forming. 20required for each leaf. Wood screwsavailable on request only.

Kawneer Tuffline Series Application

The McKINNEY K-MCK-12HDcontinuous gear hinges are recommendedfor building entrances subjected to heavytraffic an potential abuse.

These hinges are GUARANTEEDFOR THE LIFE OF THE OPENING

The flat cable conductor or electricallymodified hinges are guaranteed forfive years.

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

OPTIONAL FEATURES

LISTEDDoor Hinges

Designed for Kawneer “Tuffline” seriesaluminum doors

Kawneer Tuffline® Series is a registeredtrademark of Kawneer Company, Inc.

*Certain door and frame conditionsmay require an extra 1/32"-1/16"clearance. Excessive clearance on firerated assemblies may violate therequirements of NFPA 80.

FrameAlignmentFlange

FrameLeaf

DoorAlignmentFlange

DoorLeaf

108

Page 111: Hinge Catalog

McKINNEYHingeCatalogFullMortise -EdgeHung InsetDoorContinuousGearHinge

109 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

Electrical Modifications (Suffix)All electrically modified hinges arefurnished with our 4 conductor flat cableconnectors at each leaf and two pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harness withconnectors on one end and hard wiringon opposite end. A 4 amp fuse issupplied to protect the cable Fromoverload or surge in power. Failure toinstall the fuse voids the warranty.

• Quick Connect – Passes constant flowof current between source of powerand actuated devices in the doorQC-4; QC-8; QC-12

• Serviceable – Same as QC excepthinge supplied in three sections with8" electrically modified leaf.SER-4; SER-8; SER-12*

• Accessible – Same as QC exceptfurnished with a pivoting 8" section.ACC-4; ACC-8; ACC-12

• MM – Magnetic Monitoring

• PT – Power transfer Prep (cut out only)For Adams Rite, Securitron, Yale,Dorma & Centurion*

• EPT – Power transfer prep (cut outonly) For Von Duprin*

*PT or EPT Location Form mustaccompany your order

Refer to catalog Pages 88-90 additionalinformation on our electrical options.

Extruded 6063-T6aluminum alloy/temperwith pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

MCK-14HD SERIES

79", 83", 85", 95" and 120" lengthsare standard for nominal door heights.The MCK-14HD continuous gear hingemay be field-cut to exact door heightsand also may be ordered in customlengths. Consult the factory for minimumrequirements on custom sizes.

The MCK-14HD Series is designed foruse with doors which are the standard1-3/4" up to 2-1/4" thick.

Mounting HardwareStandard Fasteners are#12-24x7/16" FH U/C, thread forming.20 required for each leaf.

Wood screws are available upon request.

–Designed for use with hollow metalframes, where the inset conforms toS.D.I. specifications for aligning doorsand frames

–Designed for use on retrofitapplications and allows for adjustmentsin order to properly align the lock edgeof the door to the frame.

Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.

The flat cable conductor or electrically modified hinges are guaranteed for five years.

OPTIONS

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

SHORT LEAF INSET APPLICATION

LISTEDDoor Hinges

Page 112: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceContinuousGearHinge

110April2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

G – Gold Anodized FinishBL – Black Anodized FinishFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

Electrical Modifications (Suffix)

All electrically modified hinges arefurnished with our 4 conductor flatcable connectors at each leaf and pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harnesswith connectors on one end and hardwiring on opposite end. A 4 amp fuse issupplied to protect the cable fromoverload or surge in power. Failure toInstall the fuse voids the warranty

• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in the doorQC-4; QC-8; QC-12

• MM – Magnetic Monitoring

Refer to catalog Pages 88-90 additionalinformation on our electrical options.

Please note that Power Transfer Cut OutsPT & EPT are not available on this hinge.

Extruded 6063-T6aluminum alloy/temperwith pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

MCK-22HD SERIES

Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.

The McKINNEY MCK-22HDcontinuous gear hinges are designedmainly for retrofit applications wherethe door must swing completely out ofthe frame opening. This hinge isapplied to the exposed surface of thedoor and frame.

It may also be used for newconstruction including new door andframe, new door with existing frame,existing door with new frame orexisting door with existing frame.

Mounting Hardware1. Frame Portion all fasteners are12-24 x 7/16" Type C, FH U/Cthread forming screws• 12 Screws are required for frame leaf–Wood screws are available on request• 1/2x12-24 Torx Pin Head MachineScrews available on request

2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"• 4 Required per hinge• Shoulder Bolt 1/4-20 x 1” PCH• 4 Required per hinge• Pan Head Self Drilling # 12 x 3/46 Required per hinge

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

FULL SURFACE

OPTIONS

LISTEDDoor Hinges

Page 113: Hinge Catalog

McKINNEYHingeCatalogFullMortise -EdgeHungContinuousGearHinge

111 Nov.2008

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Extruded 6063-T6 aluminumalloy/temper with pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

MCK-25HD SERIES OPTIONS

G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

Electrical Modifications (Suffix)All electrically modified hinges arefurnished with our 4 conductor flat cableconnectors at each leaf and two pigtailsfor use with ElectroLynx connectors aswell as a 36" and a 72" wire harnesswith connectors on one end and hardwiring on opposite end. A 4 amp fuse issupplied to protect the cable fromoverload or surge in power. Failure toinstall the fuse voids the warranty

• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in the doorQC-4; QC-8; QC-12

• Serviceable – Same as QC excepthinge supplied in three sections with8" electrically modified leaf.SER-4; SER-8; SER-12*

• Accessible – Same as QC exceptfurnished with a pivoting 8" section.ACC-4; ACC-8; ACC-12

• MM – Magnetic Monitoring

• PT – Power transfer Prep (cut outonly) For Adams Rite, Securitron,Yale, Dorma & Centurion*

• EPT – Power transfer prep (cut outonly) For Von Duprin*

*PT or EPT Location Form mustaccompany your order

Refer to catalog Pages 88-90 additionalinformation on our electrical options.

Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.

The McKINNEY MCK-25HDcontinuous gear hinges are recommendedfor new construction and retrofitinstallations including new door andframe, new door with existing frameor existing door with new frame.

Mounting HardwareFrame Portion all fasteners are12-24 x 7/16" Type C, FH U/C threadforming screws• 20 Screws are required for each leaf–Wood screws are available on request• 1/2x12-24 Torx Pin Head MachineScrews available on request

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

SHORT LEAF FLUSH APPLICATION

LISTEDDoor Hinges

Page 114: Hinge Catalog

McKINNEYHingeCatalogFullMortise -RaisedGearContinuousGearHinge

112April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Extruded 6063-T6 aluminumalloy/temper with pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

MCK-28HD SERIES OPTIONS

G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

– Designed for use on metal or woodframes with applied casing.

– Applied as to conceal both leaves

– Full mortise hinges are designed foraluminum door and frameapplications where the hinge leaf mayinterfere with the weatherstrip orapplied stop of the frame.

Mounting HardwareMCK-28HD Continuous Gear hingesare recommended for new constructionand retrofit installations including newdoor and frame; new door and existingframe, existing door and new frame

Fasteners are # 12-24 x 7/16" Type C,FH U/C thread-forming screws

1. 20 Screws are required per each leaf

2. Wood Screws available on requestand should be specified on order

3. 1/2x12-24 Torx Pin Head MachineScrews available on request

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

Door Closed

Door Open 90°

LISTEDDoor Hinges

5/16" @ Square Edge Application

11/32" @ Beveled Edge Application

Page 115: Hinge Catalog

McKINNEYHingeCatalogHalfSurfaceContinuousHinge

113 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

Extruded 6063-T6 aluminumalloy/temper with pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

MCK-54HD SERIES OPTIONS

G – Gold Anodized FinishBL – Black Anodized FinishFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

Electrical Modifications (Suffix)All electrically modified hinges areare furnished with our 4 conductor flatcable connectors at each leaf and twopigtails for use with ElectroLynxconnectors as well as a 36" and a 72"wire harness with connectors on oneend and hard wiring on opposite end.A 4 amp fuse is supplied to protect thecable From overload or surge in power.Failure to Install the fuse voids thewarranty.

• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in thedoor QC-4; QC-8; QC-12

Refer to catalog Pages 88-90 for additionalinformation on our electrical options.

The MCK-54HD series hinge isdesigned for use with hollow metalframes, where the inset conforms toS.D.I. specifications for aligning doorsand frames

–Designed for use on retrofit applicationsand allows for adjustment in order toproperly align the lock edge of the doorto the frame.

Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.

The McKINNEY MCK-54HDcontinuous gear hinges are designedmainly for retrofit applications. Thedoor leaf is applied to the exposedsurface of the door and the frame leaf isapplied to the concealed surface of theframe rabbit. It may also be used fornew construction including new doorand frame, new door with existingframe, existing door with new frame orexisting door with existing frame.

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

HALF-SURFACE APPLICATION

MOUNTING HARDWARE

1. Frame Portion all fasteners are12-24 x 7/16" Type C, FH U/C threadforming screws• 20 Screws are required per each leaf

• Wood Screws available on requestand should be specified on order

• 1/2x12-24 Torx Pin Head MachineScrews available on request

2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"

• 4 Required per hinge

• Shoulder Bolt 1/4-20 x 1" PCH

• 4 Required per hinge

• Pan Head Self Drilling # 12 x 3/4

• 6 Required per hinge

LISTEDDoor Hinges

Page 116: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceCenterPivotContinuousHinge

114Dec.2008

©McK

INNEYProductsCom

pany2006,2007.2008

1-800-346-7707 • www.mckinneyhinge.com

Extruded 6063-T6 aluminumalloy/temper with pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

MCK-58HD SERIES OPTIONS

G – Gold Anodized FinishBL – Black Anodized FinishFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

Electrical Modifications (Suffix)All electrically modified hinges are arefurnished with our 4 conductorflat cable connectors at each leaf andtwo pigtails for use with ElectroLynxconnectors as well as a 36" and a 72"wire harness with connectors on oneend and hard wiring on opposite end.A 4 amp fuse is supplied to protect thecable from overload or surge in power.Failure to install the fuse voids thewarranty.

• Quick Connect – Passes constantflow of current between source ofpower and actuated devices in thedoor QC-4; QC-8; QC-12

Please note that Power Transfer Cut OutsPT & EPT are not available on this hinge

The MCK-58HD Series is designed foruse where pivot point must be centeredbetween the door and frame and areapplied to the exposed surface of thedoor and frame.

–Designed for use where frame face isless than 1-1/2" wide.

Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers’ standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.

The McKINNEY MCK-58HDcontinuous gear hinges are designed forretrofit work and can be used for newconstruction and renovation projectsapplications where the pivot point mustbe centered between the door andframe, or where the frame face is lessthan 1-1/2".

Door Hinge # of DoorSize Length Bearings Weight6'8" 79" 26 520 lbs7'0" 83" 27 540 lbs7'2" 85" 27 540 lbs8'0" 95" 31 620 lbs10'0" 120" 39 780 lbs

FULL-SURFACE APPLICATION

MOUNTING HARDWARE

1. Frame Portion all fasteners are12-24 x 7/16" Type C, FH U/C threadforming screws• 12 Screws are required for frame leaf

• and should be specified on order

• 1/2x12-24 Torx Pin Head MachineScrews available on request

2. Door Portion• Thru-Bolt 1/4-20 x 1-5/8"

• 8 Required per hinge

• Shoulder Bolt 1/4-20 x 1" PCH

• 8 Required per hinge

• Pan Head Self Drilling # 12 x 3/4

• 4 Required per hinge

LISTEDDoor Hinges

Page 117: Hinge Catalog

McKINNEYHingeCatalogWideThrowFull-MortiseContinuousGearHinge

115 June2010

©McK

INNEYProductsCom

pany2006,2007,2010

1-800-346-7707 • www.mckinneyhinge.com

Extruded 6063-T6 aluminumAlloy/temper with pinless assembly.

CL – Clear anodized aluminumBZ – Dark anodized aluminum

MCK-WTHD SERIES OPTIONS

G – Gold Anodized FinishBL – Black Anodized FinishHT – Hospital TipFP – Fire PinsCustom lengths – specify handing andlength in inchesCustom Finish (consult factory foravailability)

Special hinge reinforcements are notrequired. Hollow metal door and framemanufacturers standard is acceptable.Removal of hinge reinforcements in thedoor and frame is not advised.Undersizing of door must also includeclearances for lock side of door, added toclearance, to obtain the properUndersizing of door.The McKINNEY MCK-WTHDcontinuous gear hinge is recommendedfor new construction or renovationsthat require extra clearance due tospecial frame or door design and areapplied so as to conceal both leaves.These include new door and frame, newdoor with existing frame or existingdoor with new frame, or new doorapplications that require extra clearance(provides 2-3/4" clearance) due tospecial frame or door design.

Requires 5/16" clearance for square edgedoors and 3/8" clearance on bevelededge doors. Clearances noted here are forhinge edges only. Undersizing of doormust also include clearance for lock sideof door, added to hinge clearance toobtain proper undersizing of door.

Mounting Hardware1. Fasteners are # 12-24 x 7/16” Type C,FH U/C thread-forming screws

1. 20 Screws are required per each leaf2. Wood Screws available on request andshould be specified on order

3. 1/2x12-24 Torx Pin Head MachineScrews available on request

APPLICATION

7'0" 83" 21088'0" 95" 2413

Available Sizes

Door Size Hinge Length Hinge Length MM

LISTEDDoor Hinges

Page 118: Hinge Catalog

McKINNEY Hinge Catalog

Sep

t 20

11©

McK

INN

EY

Pro

duc

ts C

omp

any

2006

, 200

7

1-800-346-7707  •  www.mckinneyhinge.com

McKINNEY Hinge CatalogFull Mortise - Safety HingesContinuous Gear Hinge

116

Extruded 6063-T6 aluminum alloy/temper with pinless assembly.

CL – Clear anodized aluminum BZ – Dark anodized aluminum

MCK-35HD & MCK-38HD SERIES OPTIONS

G – Gold Anodized Finish BL – Black Anodized Finish HT – Hospital Tip Custom lengths – specify handing and length in inches Custom Finish (consult factory for availability)

1. Fasteners are # 12-24 x 7/16” Type C, FH U/C thread-forming screws

1. 20 Screws are required per each leaf

2. Wood Screws available on request and should be specified on order

3. 1/2x12-24 Torx Pin Head Machine Screws available on request– Designed mainly for new door

applications in child care and nursing facilities. These hinges require extra clearance with a special frame design and are applied as to conceal both leaves.

– The unique design prevents small fingers from getting pinched in the door.

– Safety hinges are designed for frames with no stops on the hinge jamb

Door Hinge # of Door Size Length Bearings Weight 6’8” 79” 26 520 lbs 7’0” 83” 27 540 lbs 7’2” 85” 27 540 lbs 8’0” 95” 31 620 lbs 10’0” 120” 39 780 lbs

MCK-35HD

Required 13/16” clearance for square edge doors and 27/32” clearance on beveled edge doors.

MCK-38HD

Required 13/16” clearance for square edge doors and 27/32” clearance on beveled edge doors.

Page 119: Hinge Catalog

McKINNEYHingeCatalogStainless andSteelContinuousHingesStainlessEdgeGuards

117 April2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

PRODUCT INFORMATION

Our Pin and Barrel Hinge stainless steel, 300 and 3500 Seriesand cold rolled steel 3700 Series are UL listed.

Our stainless and steel continuous hinges distribute shockforces evenly so wear and tear to the frame and door isreduced significantly. Security is enhanced by preventinginsertion of devices between the door and frame thus reducingvandalism. The continuous design allows for easy alignmentof electrical transfers and monitoring switches. These hingesalso aid in stopping air infiltration by creating a complete sealfrom top to bottom of the door at the hinge stile.

The Pin and Barrel Hinge is held together with a 1/4" stainlesssteel Teflon coated rod free moving rod. The hinge works ona split bearing assembly which eliminates premature wear andguarantees proper alignment.

The Pin and Barrel Hinge acts as reinforcement for both doorand frame. For the majority of our hinges, special hingereinforcements are not required. However door and framemanufacturers standard is acceptable and removal of hingereinforcements in the door and frame is not advised. Whenusing our HG models HG-305, HG-310, HG-322, HG-326and HG3505 in a hollow metal door application, we stronglysuggest reinforcement at the lock side of the door for properuse of the AdjustaScrews™ assembly. This addedreinforcement will ensure the proper amount of material forthreading the Adjusta-Screw, giving the assembly the strengthneeded to last the life of the opening. It is important to notethat these added reinforcements must be added to the doorat time of manufacture. Please be sure to take this intoconsideration when ordering your doors. Again, thisreinforcement applies only to the Adjusta-Screw assemblyand is not needed for any other hardware application.

Door Hinge Length Weight CapacitySize 1-3/4" Doors

Inches MM 300 & 3700 Series6'8" 78.75" 2000.2 600 lbs7'0" 83.125" 2111.4 600 lbs7'2" 85" 2159.0 600 lbs8'0" 95" 2413.0 600 lbs10'0" 118.75" 3016.2 600 lbs

Door Hinge Length Weight CapacitySize 2" Doors

Inches MM 3500 Series6'8" 78.75" 2000.2 900 lbs7'0" 83.125" 2111.4 900 lbs7'2" 85" 2159.0 900 lbs8'0" 95" 2413.0 900 lbs10'0" 118.75" 3016.2 900 lbs

CYCLE REQUIREMENTS

Both the 300 Series and 3500 Series stainless hinges meetor exceed ANSI / BHMA Standard A156.1 - Grade 1.The 3700 Series steel hinge meets or exceeds ANSI / BHMAStandard A156.1 – Grade 2.

Classified and Listed to meet the requirements ofStandards, UL10B, UL10C, UBC7-2 POSITIVE PRESSURE

Maximum Door Opening:

– Single Doors: 4'0" x 10'0"– Pair of Doors: 8'0" x 10'0"

Fire Rating3 hours– hollow metal doors mounted singly

90 minutes– hollow metal and composite core wood fire doors

20 minutes– wood doors

MOUNTING HARDWARE

To prevent warping of the door along the hinge jamb, screwsare located along the full length of the hinge. The templatedhole pattern makes these hinges are ideal for use on center-hung lead lined doors – Lead Line covers are available forsurface mount units.

Our AdjustaScrews™ fastener available on the Hinge Guardmodels permits up to 3/8” width adjustment. Full door lengthadjustment can means doors can be squared accurately andeasily in new installations and existing frames can be used inretrofits. Future adjustments can be made by the Maintenancestaff by re-positioning the Adjusta-Screw fasteners.

Please refer to the individual catalog pages for fastenerinformation.

Hinges may be field cut per installation instructions.

FINISHES

The 300 and 3500 Series stainless hinges are supplied as astandard in brushed satin finish US-32D (630) and areavailable in bright stainless US-32 (629). The 3700 seriessteel hinges are supplied in Gray Powder Coat finish. Consultthe factory for availability of custom finishes.

Page 120: Hinge Catalog

McKINNEYHingeCatalogStainless andSteelContinuousHingesStainlessEdgeGuards

118April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

HINGE NUMBERING SYSTEM

EG – Edge GuardFM – Edge MountFS – Full SurfaceHG – Hinge/GuardHM – Half MortiseHS – Half SurfaceSC – Swing Clear

This series number indicates the type of hinge and basematerial used:

Hinge Series300 14 Gauge, 304 Stainless steel barrel hinges with

stainless pin

3500 12 Gauge, 304 stainless steel pin and barrel securityhinges with stainless pin

3700 14 Gauge, 1012 Carbon steel barrel hinges withstainless pin

Hinge ModelsThe last two digits of the model number indicate theapplication:

00 – edge mount (formerly full mortise)01 – full surface, 1/8" offset02 – full surface, flush03 – half surface, 1/8" offset04 – half mortise, 1/8" offset05 – edge mount hinge/guard06 – half mortise hinge/guard07 – double hinge/guard08 – edge guard09 – full surface, swing clear10 – swing clear hinge/guard11 – edge mount, self aligningOther numbers are used for specific applications

Option SuffixesAMS – Adjustable Monitoring SwitchCC – Concealed Current TransferDD – Dutch DoorPT – Power Transfer Cut Out for Adams Rite, Securitron,Yale, Centurion & DormaEPT – Power Transfer Cut Out for Von DuprinES – Exposed Monitoring SwitchHT – Hospital TipLL – Lead LinedMB – Medical BearingsPC – Powder CoatedRB – Raised BarrelWT – Wide Throw

HANDING

Some Options including but not limited to CC, PT, EPT, HT,will require handing. Refer to the individual catalog pages.

Specify handing on all custom hinge lengths.

Custom Design

McKinney’s engineering department will be willing to assistyou in developing custom applications to solve any of yourunique door hinging problems. Together with the customer,we will go through an official sign-off process to assure customhinges fit your exact needs.

Medical Bearings for 300 series Hinges

Specially designed for hospitals and other high frequencyopenings.

Patented fiber-reinforcement polymer bearings:– Self lubricating with high resistance to wear– Uniquely designed to provide clean and quiet hingeoperation

– Exceeds ANSI/BHMA Grade 7 requirements– Support doors weighing up to 600 lbs.– 25 year warranty

Specify by suffixing “MB” to the Stainless steel hinge models

Page 121: Hinge Catalog

McKINNEYHingeCatalogStainless andSteelContinuousHingesStainlessEdgeGuards

119 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

HINGE MODIFICATIONS

Hospital Tip

Available on all models exceptspring-loaded toilet partition hinges,

FS 321 and FM 327.Suffix hinge “-HT”Helps provide a safe, clean environment

Dutch Door Prep

Available on all hinge modelsSuffix hinge “-DD”Continuous frame leaf with two-piece

door leafIndicate handing, clearances, doorand frame heights, and materials when

ordering

Wide Throw

Only available on 300 series hingesSuffix hinge “-WT”Specify distance from pin centerline to

heel edge of hinge when ordering

Reinforcement may be required onextreme wide throw applications.

These conditions will be determinedthrough a drawing approval process.

Cost will be determined at time ofapproval

BlankHoles omitted for specialapplications, such as welded installation.Not available on adjustable models.

Standard Edge Guard Cut-Outs

• 4 7/8 ASA strike • manual flush bolt• 161 latch • automatic flush bolt• 86 mortise • 161 strike

Security Studs

Stainless steel security studs mounted tothe frame leaf

Door leaf is drilled to accommodate studsThree studs installed on hinges up to 7'2"Four studs installed on hinges over 7'2"Door and frame must be specially preparedto accommodate security studs

Sheared Leaf

Used for narrow door thickness’, unevenlyrabbeted frames or other special

applicationsSpecify distance from pin centerline to

heel edge of hinge when ordering

Custom Hole PatternAny hole shape or pattern other thanMcKinney's standard templated hole

patternIndicate desired pattern and include

dimensioned diagrams when ordering

Raised Barrel (Swaged)Available on all edge mount and half

surface models except on Aluminumhinges

Required on models FS-201, FS-202,FS-301 & FS-302 in order to open 180°Suffix hinge “-RB”For cased open or center pivot doors

Page 122: Hinge Catalog

McKinneyHingeCatalogStainless andSteelContinuousHingesStainlessEdgeGuards

120April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

HINGE MODIFICATIONS

AMS Adjustable Monitoring Switch

Rigid welded assembly gives you theability to adjust your monitoringswitch to work with all applications.

Not available on aluminum hinges orpowder coat finishes.

CC Concealed Current Transfer

For 300, 3500, and 200 seriesEdge mount only. Not availableon Raised Barrel applications.

CE-4: Qty (4) 28ga wiresCE-8: Qty (8) 28ga wires

Handing required

CT Current Transfer Contact Switch

Rated for 16 amp. surge currentNo wire furnished: 1/4-20 screw postswill accommodate any gauge wire

Recommended only for low-traffic doors;requires CTP Current Transfer Prep

MP-ETAPElectrical Transfer Access Prep

Modifications that allows easy oneperson access to wiring between thehinge and door/frame.

PT or EPT Current Transfer Prep

Hinge leaf cutout to accommodate PTfor Adams Rite, Securitron, Yale,Centurion & Dorma

EPT for Von DuprinPlease provide location and handing forall locations.

Standard Edge Guard Cut-Outs

• 4 7/8 ASA strike • manual flush bolt• 161 latch • automatic flush bolt• 86 mortise • 161 strikeEdge Guard Order Form mustaccompany your order

Security Fastener

Torx Head security fastenersare available in lieu of standard fasteners.

Standard Powder Coat Finishes

MP-PC-1 Dark Bronze

MP-PC-2 Eggshell White

MP-PC-3 Semi Gloss Black

MP-PC-4 Aluminum

MP-PC-5 Sun Gold

MP-PC-6 Light Copper

MP-PC-7 Polished Brass*

* FM300 Series only

Page 123: Hinge Catalog

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

121 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

ADJUSTA-SCREW ASSEMBLY

One full turn of the ajusta-screw adjusts thewidth of the door and hinge assembly 1/16"

The door width can be adjusted up to .3/8"with the Adujsta-Screw assembly as shown

MP-7 10-32 x 3/4"Phillips flat head

undercut stainless steelmachine screw

MP-25 13/8"Adjusta-stud fastener

with 10-32 internal threadand hex head adjustment

NOTE:You must predrill your door using a 5/16"bit for every fastener.Please see instruction sheets for full details on proper prepwork and installation procedures.

Adjust screw assemblies are also approved onour Edge Guards, EG-308 and EG-T308.The Underwriters Laboratories Inc.certification file number is R15384(N)

Page 124: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

122April2006

ADJUSTA-STUD HOLLOW METAL VS WOOD

The right hand Adjusta-Stud was designed for use in a wood door application. The Adjusta-Stud will cut its own thread intothe pre-drilled pilot hole. Pre-tapping of the pilot hole is not required in a wood application.

HG-3505, HG-305, HG-310, HG-322, HG-326

MP-7 10-32 x 3/4"Phillips flat head

undercut stainless steelmachine screw

MP-25 13/8"Adjusta-stud fastener

with 10-32 internal threadand hex head adjustment

NOTE:When ordering the hinges indicated above, where the Adjusta-Stud is included at no extra charge, you must indicate whichtype of application is preferred. The standard default will provide the right hand Adjusta-Stud.

The left hand Adjusta-Stud was designed for use in a hollow metal door application. Proper reinforcement must first be appliedto the door during manufacturing to allow for tapping of the 3/8-16 left handed thread. Using this left handed stud in a hollowmetal door application will help prevent the stud from dropping into the door during hinge installation and adjustment.

Page 125: Hinge Catalog

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

123 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FM300 EDGE MOUNT OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths- specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix, may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised barrel• WT Wide Throw

Electrical Modifications (Suffix)• AMS Adjustable Monitoring Switch• CC Concealed Circuit (4 or 8 Wire)• QC Electrolynx® Concealed Circuit(4, 8 or 12 Wire)

• PT Power Transfer Prep (Cut outOnly) For Adams Rite, Securitron,Yale, Dorma & Centurion*

• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *

Consult the Factory on other availableoptions

* Power Transfer Location Templatemust accompany your order

When installed on a 16 gage (orheavier) metal frame, hinge reinforce-ments are not required, nor are theyrecommended. However, if the framesare equipped with mortise hingereinforcements, removal is not advised.

This edge-mounted pin & barrel typehinge is used on many of today’s hightraffic, high abuse doors. The hingeworks well in locations that usedanchor hinges, pivot reinforcementhinges or thrust pivot unit and hingesets. This hinge saves on special doorand frame preparation charges andmakes the installer’s job easier. It canbe used on both fire labeled andnon-labeled openings.

C US

LISTED

6'8" 78.75" 2000.2

7'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

A156.26 Grade 1

ANSI Cross Reference

Mounting HardwareNo exposed mounting fastenerswhen closedFastener screw pack includes#10x7/8" PH U/C Self Drilling, 410 S.S.#10x1-1/4" PH U/C S.S.

Capacity (1-3/4” Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter, 304 stainless steel pinLong-life split nylon bearingsExterior barrel diameter .438 (7/16)

Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 126: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEYHingeCatalogFull Surface, 1/8" InsetStainless SteelContinuousHinge

124April2006

MCK-FS301 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Brite dipped fastener cover• 1-3/4" aluminum sleeve bolts

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised Barrel• LL Lead-lined cover w/ 1/16"lead-lining

Consult the Factory on other availableoptions

When installed on a 16 gage (orheavier) metal frame, hingereinforcements are not required, nor arethey recommended. However, if theframes are equipped with mortise hingereinforcements, removal is not advised.

For 1/8" inset doors. This surfacemounted hinge can be used to repairboth fire labeled and non-labeled doorsthat have very tight clearances. Thehinge has a built-in 1/8" offset to assistin weather seal and sound barrier areas.

78.75" 2000.2

7'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed Universal screw pack includes1/4-20 x 3/4 PPH Tek SD, Zinc #8 x 3/4”PHF Tek, Zinc Cover Clip

Fastener CoverBrushed Aluminum

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 127: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceFlushMountStainless SteelContinuousHinge

125 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FS302 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Brite dipped fastener cover• 1-3/4" aluminum sleeve bolts

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised Barrel• LL Lead-lined cover w/ 1/16"lead-lining

Consult the Factory on other availableoptions

When installed on a 16 gage (orheavier) metal frame, hingereinforcements are not required, nor arethey recommended. However, if theframes are equipped with mortise hingereinforcements, removal is not advised.

For flush doors. This surface mountedhinge can be used to repair both firelabeled and non-labeled doors thathave very tight clearances, giving it aweather tight seal.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting Hardware (1-3/4" Doors)No exposed mounting fasteners whenclosed Universal screw pack includes1/4-20 x 3/4 PPH Tek SD, Zinc #8 x 3/4”PHF Tek, Zinc Cover Clip

Fastener CoverBrushed Aluminum

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 128: Hinge Catalog

McKINNEYHingeCatalogHalf SurfaceStainless SteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HS303 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised Barrel• LL Lead-lined cover w/ 1/16"lead-lining

Electrical Modifications (Suffix requireshanding)

• PT Power Transfer Prep (Cut out forframe leaf only) For Adams Rite,Securitron, Yale, Dorma & Centurion*

• EPT Power Transfer Prep (Cut out forframe leaf for frame leaf only) For VonDuprin*

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This half-surface pin & barrel typecontinuous hinge can be used to repairboth fire labeled and non-labeledopenings. The hinge fits into the gapleft after standard butt hinges areremoved. It can assist in reversing thehanding of a door, or to reverse theswing of a door hung in an evenly-rabbeted frame. (Please call the factoryat 800-346-7707. for instructions onunevenly-rabbeted frames.)

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareFastener screw pack includes#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.Cover Clip #8 x 3/4" PHF Tek, Zinc

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

126

Page 129: Hinge Catalog

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

127 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HM304 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom lengths - specify in inches• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised Barrel

Electrical Modifications (Suffix requireshanding)• PT Power Transfer Prep (Cut out doorleaf only)For Adams Rite, Securitron, Yale,Dorma & Centurion *

• EPT Power Transfer Prep (Cut out doorleaf only) For Von Duprin *

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This pin & barrel type hinge is used torepair wooden doors that have split, orare chipped and dented from trafficabuse. The surface mounted frame leafallows for easy retrofit installation.This hinge can be used to reverse thehanding or swing of the door withoutany modifications to the existing door.

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.1/4-20 x 1-3/4" Sleeve Bolt SSCover Clip #8 x 3/4" PHF Tek, Zinc

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14 Gauge 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance with UBCcode standard 7-2 for positivepressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 130: Hinge Catalog

McKINNEY Hinge CatalogHinge GuardStainless Steel Continuous Hinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HG305 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised Barrel

Electrical Modifications(Suffix requires handing)• AMS Adjustable Monitoring Switch

• CC Concealed Circuit (4 or 8 Wire)

• QC Electrolynx® Concealed Circuit(4,8 or 12 Wire)

• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion *

• EPT Power Transfer Prep (Cut out Only)For Von Duprin *

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installing on a hollow metal doorapplication we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAssembly. This added reinforcement willensure the proper amount of material forthreading the Adjusta-Screw, giving theassembly the strength needed to last thelife of the door. Remember to order yourdoors with reinforcement.

This unique design answers the problemof adjusting doors where frames are notinstalled plumb or properly aligned. Notonly that, but the wrap-around edgeguard protects the door from unsightlydents and gouges and will deflectobjects, preventing further damage.Strategically located fasteners coupledwith the AdjustaScrew fastener allowthe door to be adjusted up to 3/8"within the channel of the hinge anddistribute the load of the door down theentire length of the jamb. The properalignment of the door to the frame willallow your closers, panics magneticlocks, electronic strikes, and automaticoperators to assist you in meeting allyour life safety code requirements.

C US

LISTED

6'8" 78.75" 2000.2

7'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMAStandard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes

#10 x 7/8" PH U/C Self Drilling, 410 S.S.

#10 x 1-1/4" PH U/C S.S.

10-32 x 3/4" PH U/C S. S.

1-3/8" RH, 10-32 int., AdjustaScrews forcorrecting frame fit problems up to 3/8"

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge 304 stainless steelFinished in 32D (630)

Door Closed

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Door Open 90°

128

Page 131: Hinge Catalog

McKINNEYHingeCatalogHingeGuardStainless SteelContinuousHinge

129 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HG306 OPTIONAL FEATURES

• 32 Bright Polished• Custom lengths - specify length in inches• Custom hole pattern• Tamper-proof security• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised Barrel

Electrical Modifications(Suffix requires handing)

• PT Power Transfer Prep (Cut out doorleaf only) For Adams Rite, Securitron,Yale, Dorma & Centurion *

• EPT Power Transfer Prep (Cut out doorleaf only) For Von Duprin *

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gauge (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This barrel-type hinge is used withhollow metal frames and wood orhollow metal doors. The guard thatwraps the door covers up dents,scratches, and splitting of the door.This product covers the door’s edge andwraps the door face to prevent furtherdamage. This hinge can also be used toreverse the swing of a door.

C US

LISTED

6'8" 78.75" 2000.2

7'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes

#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.Cover Clip#8 x3 /4" PHF Tek, Zinc

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14 Gauge 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 132: Hinge Catalog

McKINNEYHingeCatalogFull Surface, SwingClearStainless SteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FS309 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Brite dipped fastener cover• 1-3/4” aluminum sleeve bolts

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• LL Lead-lined cover w/ 1/16"lead-lining

Consult the Factory on other available options

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This barrel-type hinge is used to ensurethat a door opened to a 90-degree angleis removed from the opening. Thishinge will mount on a 1 3/4" face, andis especially useful for ADA upgradework and lead lined door conversionprojects.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross ReferenceMounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes#10 x 1-1/4" PH U/C S.S.#10 x 7/8" PFH U/C SD, 410 SS1/4-20 x 3/4 PPH Tek SD, Zinc#8 x 3/4" PHF Tek, ZincCover Clip

Fastener CoverBrushed Aluminum

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

130

Page 133: Hinge Catalog

McKINNEYHingeCatalogEdgeMount,Half-WrapEdgeGuardStainless SteelContinuousHinge

131 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HG310 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised barrel

ToolsMTSP-100 Right angle skew driver forease of installation

Consult the Factory on other available options

When installing on a hollow metal doorapplication we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAssembly. This added reinforcement willensure the proper amount of material forthreading the Adjusta-Screw, giving theassembly the strength needed to last thelife of the door. Remember to order yourdoors with reinforcement.

ADA-compliant barrel-type hinge isused on operating room doors to swingthe door out of the opening whenmoving equipment in and out. Thehinge guard also protects the door fromdents and gouges.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed Fastener screw pack includes

#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.10-32 x 3/4" PH U/C S. S.1-3/8" H, 10-32 int., AdjustaScrews forcorrecting frame fit problems up to 3/8"

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 134: Hinge Catalog

McKINNEYHingeCatalogSwingClear,Half-WrapEdgeGuardStainless SteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HG311 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised barrel

Tools

MTSP-100 Right angle skew driver forease of installation

Consult the Factory on available options

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

ADA Compliance

This surface applied swing clear versionallows doors to meet ADA requirements.The single wrap protects door edgesfrom cart damage.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosedFastener pack includes#10 x 7/8 PHF U/C SD 410 SS#10 x 1-1/4" PHF U/C SS

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

132

NOTE:If installing on beveled edge doors, the use ofAdjustaScrews may be required to correct doorand frame fit problems.

Page 135: Hinge Catalog

McKINNEYHingeCatalogEdgeMount,Half-WrapEdgeGuardStainless SteelContinuousHinge

133 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HG315 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised barrelElectrical Modifications (Suffix requireshanding)

• AMS Adjustable Monitoring Switch• CC Concealed Circuit (4 or 8 Wire)• QC Electrolynx® Concealed Circuit(4, 8 or 12 Wire)

• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion *

• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *

Consult the Factory on other availableoptions

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

Featuring our unique edge guard, thiseconomical hinge prevents objectsbeing placed between the door andframe as well as protecting the door’sedge while supporting the door’s weightalong the entire length of the jamb.The EG-C308 Edge Guard when usedwith this hinge makes for a nicelybalanced look.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes#10 x 7/8" PFH U/C SD 410 SS#10 x 1-1/4" PFH U/C SS

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 136: Hinge Catalog

McKINNEYHingeCatalogFull Surface, 3/4" InsetStainless SteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FS321 OPTIONAL FEATURES

• DD Dutch door hinges (DD Form

• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• LL Lead lined cover with 1/16" leadlining

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This surface mount pin & barrel modelwas developed to work in conjunctionwith existing 3/4" offset floor closers.Where top or intermediate pivots haveworn and the floor closer will remain,the FS-321 is the solution to extendingthe life of the opening.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes1/4-20 x 3/4 PPH Tek SD Zinc#8 x 3/4" PHF Tek, ZincCover Clip

Fastener CoverBrushed Aluminum

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14 Gauge, stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

134

Page 137: Hinge Catalog

McKINNEYHingeCatalogEdgeMount, Full-WrapHingeGuardStainless SteelContinuousHinge

135 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HG322 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Brite dipped fastener cover• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised barrel

Electrical Modifications (Suffix requireshanding)

• AMS Adjustable Monitoring Switch• CC Concealed Circuit (4 or 8 Wire)• QC Electrolynx® Concealed Circuit(4, 8 or 12 Wire)

• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion *

• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installing on a hollow metal doorapplication we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAssembly. This added reinforcementwill ensure the proper amount of materialfor threading the Adjusta-Screw, givingthe assembly the strength needed to lastthe life of the door. Remember to orderyour doors with reinforcement.

All the features of the HG-305Hinge/Guard plus 2” extensions. Thisunique design answers the problem ofadjusting doors where frames are notinstalled plumb or properly aligned. Notonly that, but the wrap-around edgeguard protects the door from unsightlydents and gouges and will deflectobjects, preventing further damage.Strategically located fasteners coupledwith the AdjustaScrew fastener allowthe door to be adjusted up to 3/8" withinthe channel of the hinge and distributethe load of the door down the entirelength of the jamb. The proper alignmentof the door to the frame will allow yourclosers, panics magnetic locks, electronicstrikes, and automatic operators to assistyou in meeting all your life safety coderequirements.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMAStandard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed

Fastener screw pack includes

#10 x 7/8" PH U/C Self Drilling, 410 S.S.

#10 x 1-1/4" PH U/C S.S.

10-32 x 3/4" PH U/C S. S.

1-3/8" RH, 10-32 int., AdjustaScrews forcorrecting frame fit problems up to 3/8"

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door ClosedDoor Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 138: Hinge Catalog

McKINNEYHingeCatalogEdgeMount, Full-WrapHingeGuardStainless SteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-HG323 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Brite dipped fastener cover• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised barrel

Electrical Modifications (Suffix requireshanding)

• AMS Adjustable Monitoring Switch• CC Concealed Circuit (4 or 8 Wire)• QC Electrolynx® Concealed Circuit(4, 8 or 12 Wire)

• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion *

• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This extended wrap model allows youto sandwich the door between two leafsof stainless steel and thru-bolt themtogether. Ideal for salvaging doorswhich have split. This hinge has all ofthe features of the MCK HG-305 plus2" extensions.

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed

Fastener screw pack includes

#10 x 7/8" PH U/C Self Drilling, 410 S.S.

#10 x 1-1/4" PH U/C S.S.

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-Duty 14, Gauge 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance with UBCcode standard 7-2 for positivepressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

136

Page 139: Hinge Catalog
Page 140: Hinge Catalog

McKINNEYHingeCatalogEdgeMount, SafetyHingeStainless SteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FM327 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Torx Security Screws 1/2 x 12-24• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• MB Medical Bearings• RB Raised barrel

Electrical Modifications (Suffix requireshanding)• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion *

• EPT Power Transfer Prep (Cut outOnly) For Von Duprin *

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This unique design prevents smallfingers from getting pinched in thedoor. It is ideal for elementary schools,day care, childcare, and nursing homefacilities. This full-length continuoushinge also provides privacy by blockingsight lines into rooms. The hinge mustbe used with a cased open type frame.

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.0

8'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes

#10 x 7/8" PH U/C Self Drilling, 410 S.S.#10 x 1-1/4" PH U/C S.S.

Capacity (1-3/4" Doors)Supports weights up to 600lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

This Hinge is not fire rated.

138

Page 141: Hinge Catalog

McKINNEYHingeCatalogEdgeMountSecurityStainless SteelContinuousHinge

139 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FM3500 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Plug weld hole pattern• Torx Security Screws 1/2 x 12-24• Special sheared leaf• Security Stud Option

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• RB Raised barrel

Electrical Modifications (Suffix requireshanding)• AMS Adjustable Monitoring Switch• CC Concealed Circuit (4 or 8 Wire)• QC Electrolynx® Concealed Circuit(4, 8 or 12 Wire)

• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion*

• EPT Power Transfer Prep (Cut outOnly) For Von Duprin*

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements are notrequired, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This hospital tip, edge mount pin andbarrel type hinge is fabricated withextra-heavy duty components for useon high traffic, high abuse doors. Thehinge is specially designed and wellsuited for correctional facilities andother high security locations using 2"thick swing-type doors. Prison doors,gates, extremely tall doors and extraheavy doors are all good candidates forthe 3500 Security Hinge.

Abuse TestingExceeds ASTM-F-1450-A–The MCK-FM3500 was subjected to aseries of impacts generated by a RamPendulum System. 400 blows weredelivered to the lock, 100 ti the cornerof the vision lite and 150 each to threeseparate locations along the hinge. Inorder to pass, the door assembly cannotbe damaged to the extent that forcibleegress can be achieved, and the doormust be capable of being unlockednormally.

6'8" 78.75" 2000.2

7'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed#1/2x12-24 PFHMS U/C S.S.

Capacity (2" Doors)Supports weights up to 900lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter .510

Heavy-duty 12 Gauge (.105”), 304stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Page 142: Hinge Catalog

McKINNEY Hinge Catalog

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

FM-3500 SECURITY STUD LOCATIONS FOR 8' 0"& 7' 0"

A 5/8" x 1/8" hole is required in the door to receive thesecurity stud.

FM-3500 SECURITY STUD OPTION

The 1/2" diameter x 1/4" projected 3O4 stainless SecurityStud is permanently mounted to the frame leaf and extendsthrough the door leaf into the door for added security.There are 3 Security Studs required for the 7'O" hinge and4 required for the 8'O" hinge. A 5/8" x 1/8" hole is requiredin the door to receive the Security Stud.

140

Page 143: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceSecurity, for 1/8” InsetDoorsStainless SteelContinuousHinge

141 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FS3501 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Bright dipped fastener cover• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Plug weld hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• RB Raised barrel

Consult the Factory on other available options

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

For 1/8" inset doors. This hinge allowsfor perfect alignment for the retrofittingof doors in correctional facilities andother high security locations using 2"thick swing-type doors. Prison doors,gates, extremely tall doors and extraheavy doors are all good candidates forthe 3501 Security Hinge.

C US

LISTED

6'8" 78.75" 2000.2

7'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed#1/2 x 12-24 PFHMS U/C S.S.

Capacity (2" Doors)Supports weights up to 900lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter .510

Heavy-Duty 12 gauge (.105), 304stainless material.Finished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Abuse TestingExceeds ASTM-F-1450-92

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 144: Hinge Catalog

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

MCK-FS3502 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Plug weld hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• RB Raised barrel

Consult the Factory on other available options

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This surface-mounted pin and barreltype hinge is fabricated with extra-heavy duty components and designedfor solving door sag problems on hightraffic - high abuse doors. This hinge iswell suited for correctional facilities andother high security locations using 2"thick swing type doors. Prison doors,gates extremely tall doors and extraheavy doors are all good candidates forthis 3502 Security Hinge.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed#1/2 x 12-24 PFHMS U/C S.S.

Capacity (2" Doors)Supports weights up to 900lbs.4'0" maximum door width(2" Doors)

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter .510

Heavy-Duty 12 gauge (.105), 304stainless materialFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Abuse TestingExceeds ASTM-F-1450-92

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

1-800-346-7707 • www.mckinneyhinge.com142

Page 145: Hinge Catalog

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

MCK-HG3505 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• RB Raised barrel

Electrical Modifications (Suffix requireshanding)

• AMS Adjustable Monitoring Switch• CC Concealed Circuit (4 or 8 Wire)• QC Electrolynx® Concealed Circuit(4, 8 or 12 Wire)

• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion *

• EPT Power Transfer

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installing on a hollow metal doorapplication we strongly suggestreinforcement at the hinge side of thedoor for proper use of the Adjusta-ScrewAssembly. This added reinforcementwill ensure the proper amount of materialfor threading the Adjusta-Screw, givingthe assembly the strength needed to lastthe life of the door. Remember to orderyour doors with reinforcement.

This unique design solves the problemof aligning doors and lockingmechanisms crucial in any securityapplication. It also solves the problemwhen adjusting doors where frames arenot installed plumb or properly aligned.The incorporated edge guard protectsthe door from unsightly dents andgouges while also protecting the hingefrom vandalism. The proper alignmentof the door to the frame will allow yourclosers, panics, magnetic locks, electronicstrikes and automatic operators to assistyou in meeting all your life safety coderequirements.

C US

LISTED

6'8" 78.75" 2000.2

7'0" 83.125" 2111.47'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 1ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosed12-24 S.S. Phillips F.H.M.S.1-3/8 RH, 12-24 int., Adjusta Screws forcorrecting alignment problems up to 3/8"

Capacity (2" Doors)Supports weights up to 900lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 12 Gauge (.105”), hingeleafs; 16 Gauge returns on door leaf, 304stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

1431-800-346-7707 • www.mckinneyhinge.com

Page 146: Hinge Catalog

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FM3700 OPTIONAL FEATURES

• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• RB Raised barrel

Electrical Modifications (Suffix)

• CC Concealed Circuit (4 or 8 Wire)• QC Electrolynx® Concealed Circuit(4, 8 or 12 Wire)

• PT Power Transfer Prep (Cut out Only)For Adams Rite, Securitron, Yale,Dorma & Centurion *

• EPT Power Transfer

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This edge-mounted pin & barrel typehinge is used on many of today’s hightraffic, high abuse doors. The hingeworks well in locations that usedanchor hinges, pivot reinforcementhinges or thrust pivot unit and hingesets. This hinge saves on special doorand frame preparation charges andmakes the installer’s job easier. It canbe used on both fire labeled and non-labeled openings.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 2ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes#10 x 7/8" PH U/C Self Drilling, Zinc

#10 x 1-1/4" PH U/C Zinc

Capacity (1-3/4" Doors)Supports weights up to 600 lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge, 1012 carbon steel,Gray Powder Coat

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

144

Page 147: Hinge Catalog

McKINNEYHingeCatalogFull Surface, 1/8" InsetSteelContinuousHinge

145 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FS3701 OPTIONAL FEATURES

• Custom lengths - specify handing andlength in inches

• 1-3/4" aluminum sleeve bolts

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• RB Raised barrel

• LL Lead-lined cover w/ 1/16” lead-lining

Consult the Factory on other available options

* Power Transfer Location Template mustaccompany your order

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

For 1/8" inset doors. This surface-mounted pin & barrel type continuoushinge can be used to repair both firelabeled and nonlabeled doors that havevery tight clearances. The hinge has abuilt-in 1/8" offset to assist in weatherseal and sound barrier areas.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 2ANSI / BHMA Standard A156.26

ANSI Cross ReferenceMounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes1/4-20 x 3/4" PPH Tek, SD, Zinc#8 x 3/4 PFH Tek, ZonkCover Clip

Fastener CoverBrushed Aluminum

Capacity (1-3/4" Doors)Supports weights up to 600 lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handedFor use on center hung lead lined doors

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge 1012 carbon steel,Gray Powder Coat

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 148: Hinge Catalog

McKINNEYHingeCatalogFull SurfaceFlushMountSteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK-FS3702 OPTIONAL FEATURES

• Custom lengths - specify handing andlength in inches

• 1-3/4" aluminum sleeve bolts

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• RB Raised barrel• LL Lead-lined cover w/ 1/16" lead-lining

Consult the Factory on other available options

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

For flush doors. This surface-mountedpin & barrel type continuous hinge canbe used to repair both fire labeled andnon-labeled doors that have very tightclearances.

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 2ANSI / BHMA Standard A156.26

ANSI Cross ReferenceMounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes1/4-20 x 3/4" PPH Tek, SD, Zinc#8 x 3/4 PFH Tek, ZonkCover Clip

Fastener CoverBrushed Aluminum

Capacity (1-3/4" Door)Supports weights up to 600 lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge, 1012 carbon steel,Gray Powder Coat

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

146

Page 149: Hinge Catalog

McKINNEYHingeCatalogHalf SurfaceSteelContinuousHinge

147 January2008

©McK

INNEYProductsCom

pany2006,2007,2008

1-800-346-7707 • www.mckinneyhinge.com

MCK-HS3703 OPTIONAL FEATURES

• US32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern• Tamper-proof security screws• 1-3/4" aluminum sleeve bolts• Special sheared leaf

Options (Suffix may require handing)• DD Dutch door hinges (DD FormRequired)

• HT Hospital tips• RB Raised barrel• LL Lead-lined cover w/ 1/16" lead-lining

Electrical Modifications (Suffix requireshanding)• PT Power Transfer Prep (Cut out frameleaf only) For Adams Rite, Securitron,Yale, Dorma & Centurion*

• EPT Power Transfer Prep (Cut out,frame leaf only) For Von Duprin*

Consult the Factory on other available options

When installed on a 16 gage (or heavier)metal frame, hinge reinforcements arenot required, nor are they recommended.However, if the frames are equipped withmortise hinge reinforcements, removal isnot advised.

This half-surface pin & barrel typecontinuous hinge can be used to repairboth fire labeled and non-labeledopenings. The hinge fits into the gapleft after standard butt hinges areremoved. It can assist in reversing thehanding of a door, or to reverse theswing of a door hung in an evenly-rabbeted frame. (Please call the factoryat 800-346-7707. for instructions onunevenly-rabbeted frames.)

C US

LISTED

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.0

10'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Grade 2ANSI / BHMA Standard A156.26

ANSI Cross Reference

Mounting HardwareNo exposed mounting fasteners whenclosedFastener screw pack includes#10 x 7/8" PH U/C Self Drilling, Zinc#10 x 1-1/4" PH U/C ZincCover Clip#8 x 3/4" PHF Tek, Zinc

Fastener CoverBrushed Aluminum

Capacity (1-3/4" Door)Supports weights up to 600 lbs.4'0" maximum door width

Hole PatternSymmetrically templatedNon-handed

Barrel Type Hinge1/4" diameter stainless steel pinLong-life split nylon bearings

Exterior Barrel Diameter.438 (7/16)

Heavy-duty 14 Gauge, 1012 carbon steel,Gray Powder Coat

Door Closed

Door Open 90°

Classified in accordance withUBC code standard 7-2 forpositive pressure

Fire Rating3 hours- hollow metal doors mounted

singly

90 minutes- hollow metal andcomposite core wood fire doors

20 minutes- wood doors

Page 150: Hinge Catalog

McKINNEY Hinge Catalog

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

CUTTING HINGES TO CUSTOM LENGTHS

Pin & Barrel Hinges

1. The following instructions will apply to all McKinney pinand barrel hinges. The general instructions apply to both300 and 3700 series hinges.

2. Determine the amount that the hinge needs to beshortened. Note the hand of the hinge before beginning tolay out your cut. All cuts will be done at the bottom ofyour hinge assembly making sure to leave the gang holepattern at the top.

3. Measure from the top down and scribe a cut line on yourleaf at the desired length.

4. Cut the hinge to length with a hacksaw, going through theleafs, barrel and pin. If necessary, use a file to removesharp edges and deburr.

5. Slide the stainless steel pin out approximately 1" makingsure the assembly stays together as one unit. Remove 1/4"from the end of the pin using a hacksaw and then pushback into it's original position.

6. Using a pair of vice-grips, crimp the end of the steel barrelmaking sure the hinge pin will not slide out.

6.

148

Page 151: Hinge Catalog

McKINNEY Hinge Catalog

149 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK EG-308 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern for lead line doors• DD – Dutch door guard application• #10-32 x 3/4 PFH U/C Stainless• AS - Adjusta Screws for correctingalignment problems up to 3/8”

Adjusta Screw assemblies are approvedfor use on labeled doors. UL Certificationfile #R15384 (N)

This edge guard which can make doorsadjustable to non-plumb frames protectsthe leading edge of the door is used inconjunction with the McK-HG305 fora balanced aesthetic look.

When using this edge guard in aHollow Metal Door application, westrongly suggest your doors be orderedand manufactured with reinforcementat the lock side of the door for properuse of the Adjusta-Screw Assembly.

This added reinforcement will ensurethe proper amount of material forthreading the Adjusta-Screw, givingthe strength needed to last the life ofthe door. This reinforcement onlyapplies to Adjusta-Screw assembly andis not needed for any other hardwareapplication.

6'8" 78.75" 2000.27'0" 83.125" 2111.4

7'2" 85" 2159.08'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Mounting Hardware#10 x 1-1/4 PFH U/C Stainless

Door EdgeSpecify square of beveled edge

Hole PatternSymmetrically templatedNon-handed

Heavy-Duty 16 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed Door Open 90°

Classified in accordance with UBCcode standard 7-2 fire test of doorassemblies for positive pressure

– also Miscellaneous Firedoor Accessory 8N60

Fire RatingUp to 1-1/2 hours, for use on wood,plastic coated wood composite andhollow metal fire rated door.

MAY NOT APPLY TO ALL WOODDOORS IN ACCORDANCE WITHUBC STANDARD CODE 7-2.PLEASE CONSULT FACTORYFOR SPECIFIC WOOD DOORAPPLICATIONS.

• Flush Bolts• ASA Strike• 86 edge and ASA lock• Hospital latch• 161 cutoutMeasurements should be given from Topof door to centerline of cutout. The EdgeGuard Order Form must accompanyyour order.Please note that hinge cut outs are notavailable at this time

HARDWARE CUTOUTS(requires handing)

Page 152: Hinge Catalog

McKINNEY Hinge Catalog

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK EG-C308 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern for lead line doors• DD – Dutch door guard application

This edge guard which protects theleading edge of the door from dentsand gouges is used in conjunction withthe McK-HG315 for a balancedaesthetic look.

6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Mounting Hardware#10 x 1-1/4 PFH U/C Stainless

Door EdgeSpecify square of beveled edge

Hole PatternSymmetrically templatedNon-handed

Heavy-Duty 16 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed

Door Open 90°

Classified in accordance with UBCcode standard 7-2 fire test of doorassemblies for positive pressure

– also Miscellaneous Firedoor Accessory 8N60

• Flush Bolts• ASA Strike• 86 edge and ASA lock• Hospital latch• 161 cutoutMeasurements should be given from Topof door to centerline of cutout. The EdgeGuard Order Form must accompanyyour order.Please note that hinge cut outs are notavailable at this time

HARDWARE CUTOUTS(requires handing)

Fire RatingUp to 1-1/2 hours, for use on wood,plastic coated wood composite andhollow metal fire rated door.

MAY NOT APPLY TO ALL WOODDOORS IN ACCORDANCE WITHUBC STANDARD CODE 7-2.PLEASE CONSULT FACTORYFOR SPECIFIC WOOD DOORAPPLICATIONS.

150

Page 153: Hinge Catalog

McKINNEYHingeCatalog300SeriesStainless Steel EdgeGuard

151 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MCK EG-T308 OPTIONAL FEATURES

• 32 Bright Polished stainless (629)• Custom lengths - specify handing andlength in inches

• Custom hole pattern for lead line doors• DD – Dutch door guard application• #10-32 x 3/4 PFH U/C Stainless• AS - Adjusta Screws for correctingalignment problems up to 3/8”

Adjusta Screw assemblies are approvedfor use on labeled doors. UL Certificationfile #R15384 (N)

The integral overlapping astragal of thisedge guard provides an additional levelof security by acting as a latchprotector. It is ideal for exterior pairs ofdoors that require protection fromvandalism. This edge guard also makesdoors adjustable to non-plumb frames.

When using this edge guard in aHollow Metal Door application, westrongly suggest your doors be orderedand manufactured with reinforcementat the lock side of the door for properuse of the Adjusta-Screw Assembly.

This added reinforcement will ensurethe proper amount of material forthreading the Adjusta-Screw, giving thestrength needed to last the life of thedoor. This reinforcement only appliesto Adjusta-Screw assembly and is notneeded for any other hardwareapplication.

6'8" 78.75" 2000.27'0" 83.125" 2111.47'2" 85" 2159.0

8'0" 95" 2413.010'0" 118.75" 3016.2

Available Sizes

Door Size Hinge Length Hinge Length MM

Mounting Hardware#10 x 1-1/4 PFH U/C Stainless

Door EdgeSpecify square of beveled edge

Hole PatternSymmetrically templatedNon-handed

Heavy-Duty 16 Gauge, 304 stainless steelFinished in 32D (630)

Door Closed Door Open 90°

Classified in accordance with UBCcode standard 7-2 fire test of doorassemblies for positive pressure

– also Miscellaneous Firedoor Accessory 8N60

Fire RatingUp to 1-1/2 hours, for use on wood,plastic coated wood composite andhollow metal fire rated door.

MAY NOT APPLY TO ALL WOODDOORS IN ACCORDANCE WITHUBC STANDARD CODE 7-2.PLEASE CONSULT FACTORYFOR SPECIFIC WOOD DOORAPPLICATIONS.

• Flush Bolts• ASA Strike• 86 edge and ASA lock• Hospital latch• 161 cutoutMeasurements should be given from Topof door to centerline of cutout. The EdgeGuard Order Form must accompanyyour order.Please note that hinge cut outs are notavailable at this time

HARDWARE CUTOUTS(requires handing)

Page 154: Hinge Catalog

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

MT-SP-100

Right angle drive skewdriverThis member of McKinney’s line of installation tools is the MT-SP100 Right Angle Drive Skewdriver. Its unique gearingdesign gives conventional screwdriver action on hard-to-reach fasteners, and the adjustable stabilizer wing provides extrastability in high torque and restricted locations. Heavy-duty construction- with die-cast housing and hardened steel gears.

This tool is especially helpful when installing our MCK-HG310 and MCK-HG311 models.

152

Page 155: Hinge Catalog

McKINNEYHingeCatalogEdgeMountStainlessSteelContinuousHinge

153 April2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

PREVENTING MORTAR FROM BREAKING DRILLS AND TAPS

Preventing mortar from breaking drills and tapsOne way to ease installation of continuous hinges in the field on new construction projects is to coordinate with the anchoringand hollow metal supplier prior to frame installation, by placing a 1/4" or 3/8" strip of expanded polystyrene insulation on theback of the hollow metal frame as shown below. When the frames are grouted in, the foam backer will allow drilling andtapping without dulling or breaking the installers bits.

You'll be a hero with the installer, contractor and architect!

Page 156: Hinge Catalog

McKINNEY Hinge Catalog

INTENTIONALLYLEFTBLANK

1-800-346-7707 • www.mckinneyhinge.com154

Page 157: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross Reference

i April2003

This cross reference is intended for theuse of architects and contract hardwaredistributors in establishing comparisonsbetween the hinge products ofMcKINNEY and other manufacturers.

These listings have been carefullycompiled from the most recentcatalogs of the manufacturers involvedand it is believed that it represents afair comparison between the product

lines. While all contract gradehardware is to be manufactured inaccordance with BHMA and ANSIstandards, McKINNEY assumes noresponsibility for the accuracy of thislist of competitors’ numbers andsuggests that both manufacturers’catalog and templates be consulted foradditional information.

McKINNEY welcomes theopportunity to consult with any

architect, distributor, contractor orbuilder at any time regarding anymatter concerning the specificationof our products.

Note: McKINNEY pioneered the use of “OilLite” bearings in 1935 for improved bearingperformance. The standard five knucklebearing hinges manufactured by McKINNEYare furnished with oil-impregnated bearings(TA). However, ball bearings can be suppliedas specified.

Hinges, Spring Hinges, Misc.ANSI Hinge Standard Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iiBommer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iiiHager Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ivLawrence Brothers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vStanley Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viUnited States Government Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii

Aluminum Continuous HingesMarkar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii-ixRoton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii-ixSelect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii-ixStanley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii-ix

Stainless Continuous HingesGallery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viiMarkar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viiStanley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii

Finish SymbolsUnited States Government Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xLawrence Brothers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xStanley Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xHager Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x

Table of Contents Page

Page 158: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross ReferenceANSI Hinge Standard Numbers

iiApril2003

ANSI McKINNEY

A5212 TA3374 (32-32D)

TA374 (32-32D)TA3324 (32-32D)

A5311 T4A3381 (32-32D)TA381 (32-32D)TA3361 (32-32D)

A5361 T4A3385 (32-32D)A5411 T4A3382 (32-32D)

TA382 (32-32D)TA3362 (32-32D)

A5412 TA2372 (32D)TA372 (32D)

A5551 TA392TA393

A8111 T4A3786TA786TA3750

A8112 TA2714TA714TA2731

A8121 T4A3795

TA795TA3765

A8122 TA2895A8133 T2714

T714T2731

A8142 TA2714 Type II

A8152 TA2714 Type IA8173 2705A8211 T4A3784

TA784

TA3764A8212 TA2774

TA774TA2724

A8221 T4A3789

TA789TA3769

A8233 T2774

A8311 T4A3781

ANSI McKINNEY

A1612 TA3383

A1711 TA3329A1882 DS-6A2111 T4A3386

TA386TA3350

A2112 TA2314TA314

TA3331A2133 T2314A2142 TA2314 - Type IIA2152 TA2314 - Type I

A2211 T4A3384TA384TA3364

A2212 TA3374TA374TA3324

A2311 T4A3381

TA381TA3361

A2361 T4A3385A2411 T4A3382

TA382TA3362

A2412 TA372

TA2372A2551 TA392

TA393TA5392

A2742 EP-5A5111 T4A3386 (32-32D)

TA386 (32-32D)TA3350 (32-32D)

A5112 TA2314 (32-32D)TA314 (32-32D)TA3331 (32-32D)

A5133 T2314 (32-32D)A5211 T4A3384 (32-32D)

TA384 (32-32D)TA3364 (32-32D)

ANSI McKINNEY

A8311 TA781

TA3761A8312 TA2771

TA771TA2741

A8321 T4A3797TA797TA3767

A8361 T4A3785A8411 T4A3782

TA782TA3762

A8412 TA2772TA772

TA2732A8421 T4A3796

TA796TA3769

A8433 T2772A8551 TA792

TA793

TA5792K61091 CS1K63201 4007K81041 3", 4", 5", 6" 1001

8" 9001K81071 1502K81071F 1502

K81081 1572K8108F 1572K81111 8" 19001K81131 HS1001K81151 6 X 4-1/2 1001K82011 8007

K82021 H8007K82183 3001K87431 35K87441 9" 451

11" 45213" 453

ANSI Hinge Standard and McKINNEY Equivalent Numbers

Note: NFPA requires that all hinges or pivots, except spring hinges, installed on labeled doors be of thebearing type. Acceptable hinge material - steel or stainless steel. (Spring hinges available in steel only.)Ball Bearings available upon request.

ANSI # McKINNEY # ANSI # McKINNEY # ANSI # McKINNEY #

Page 159: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross ReferenceBommer Industries Inc. Numbers

iii April2003

Feature Bommer McKINNEY

Non-Removable Pin N NRP (Suffix)

Security Stud S SSF (Suffix)Non-Removable Pinwith Security Stud

A NRP x SSF (Suffix)

Maximum Security Stud M PSF (Suffix)

Hospital Tip H HT (Prefix)

Decorative Ball Tip Decorative Ball Tip BT (Suffix)

Decorative Steeple Tip Decorative Steeple Tip ST (Suffix)

Stainless Steel Pins J SSP (Suffix)Brass Pins K BR

BB5042 RBMTA2314-32D

BB5044 RBT4A3786

BB5045 RBT4A3386

BB5046 RBT4A3386-32D

BB5050 TA2714 Slip-in Type 2BB5051 TA2314 Slip-in Type 2

BB5052TA2314-32DSlip-in Type 2

BB5060 TA2714 CCBB5061 TA2314 CC

BB5062 TA2314-32D CC

BB5064 T4A3786 CC

BB5065 T4A3386 CC

BB5066 T4A3386-32D CC5100 T2774

BB5101 TA3374

BB5102 TA3374-32D

BB5104 T4A3784

BB5105 T4A3384BB5106 T4A3384-32D

BB5124 T4A3789

BB5200 TA2771

BB5201 TA3341

BB5204 T4A3785BB5205 T4A3385

BB5224 T4A3797

BB5226 T4A3397-32D

5300 T2772

BB5300 TA2772BB5301 TA2372

BB5302 TA2372-32D

BB5304 T4A3782

BB5305 T4A3382

MB-1 MG-16

170 352410 451

2430 453

3023 HS1001

3024 19001

3029 10013029 (8") 9001

4310 1502

4313 1572

5000 T2714

5001 T23145002 T2314-32D

BB5000 TA2714

BB5001 TA2314

BB5002 TA2314-32D

BB5004 T4A3786BB5005 T4A3386

BB5006 T4A3386-32D

BB5010 TA2798

BB5011 TA2398

BB5012 TA2398-32DBB5014 T4A3786

BB5015 T4A3386

BB5016 T4A3386-32D

BB5020 TA2895

BB5021 TA2395BB5022 TA2395-32D

BB5024 TA3795

BB5026 T4A3395-32D

BB5034 TA792

BB5040 RBMTA2714BB5041 RBMTA2314

BB5306 T4A3382-32D

BB5324 T4A37967112 4007RB

7112 4007MRB

7512 8007

H7512 H8007

7811 30017812 J3001

8000 T714

8001 T314

8002 T314-32D

BB8000 TA714BB8001 TA314

BB8002 TA314-32D

BB8004 TA786

BB8005 TA386

BB8006 TA386-32DBB8024 TA795

BB8034 TA792

BB8036 TA392

BB8040 RBMTA714

BB8044 RBMTA786BB8060 TA714 CC

BB8064 TA786 CC

BB8100 TA774

BB8101 TA374

BB8102 TA374-32DBB8104 TA784

BB8105 TA384

BB8106 TA384-32D

BB8124 TA789

BB8200 TA771BB8201 TA371

BB8202 TA371-32D

BB8204 TA781

BB8205 TA381

BB8206 TA381-32DBB8224 TA797

BB8300 TA772

BB8301 TA372

BB8302 TA372-32D

BB8304 TA782BB8305 TA382

BB8306 TA382-32D

BB8324 TA796

Bommer Industries Inc. Numbers and McKINNEY Equivalent Numbers

Bommer # McKINNEY # Bommer # McKINNEY # Bommer # McKINNEY #

Options

Page 160: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross ReferenceHager Catalog Numbers

ivApril2003

OptionsFeature Hager McKINNEY

Suffix for Electric Hinges

1191 T2314BB1191 TA2314BB1193 TA3313BB1199 T4A33861250 15021253 1572BB1264 T4A3789BB1265 T4A4789BB1266 T4A3797BB1260 TA2895BB1261 TA4895BB1262 T4A3795BB1263 T4A4795BB1265 T4A4789BB1270 T4A3796BB1277 TA2714 Slip-inBB1278 TA2714 Slip-inRC1279 RC27141279 T2714BB1279 TA2714WTBB1279 TA2798BB1577 TA2314 Slip-inBB1578 TA2314 Slip-in1741 1400RC1741 14141804 7031808 705RC1841 1458BB2098 T4A3384BB2109 T4A3381BB2108 T4A3385BB2110 TA2371BB2112 TA2372BB2113 T4A3382BB2169 T4A3781BB2168 T4A3785BB2171 TA2771BB7508 TA5792BB8508 TA5392

E ESETM CCxMMETW CCEMN MMEIS CS

Hager Catalog Numbers and McKINNEY Equivalent Numbers

Hager # McKINNEY # Hager # McKINNEY # Hager # McKINNEY #

BB7506 TA792BB7507 TA5792BB800 TA314BB801 TA374BB802 TA371BB803 TA372BB850 TA386BB851 TA384BB852 TA381BB853 TA382BB858 TA393920 T2731AB920 TA2731BB8505 TA393BB8506 TA392BB8507 TA53921250 15021256 81330BB1109 TA33741129 T2774BB1129 TA2774BB1138 T4A3784BB1163 T4A3782BB1168 T4A37861173 T2772BB1173 TA2772BB1174 TA3713

417 BP-10418 BP-11451 DLS-8452 DLS-8453 DLS-8454 DLS-8495 R1-TOP496 R2-CENTER497 R3-BOTTOM600 EPS & DS6610 DS-6700 T714BB700 TA714BB701 TA774BB702 TA771BB703 TA772BB750 TA786BB751 TA784BB752 TA781BB753 TA782BB7501 TA795BB7501 TA5795BB7511 TA789BB7512 TA5789BB7523 TA797BB7534 TA796BB7505 TA793

Raised Barrel RBB RBM (Prefix)

Raised Barrel RBS RBS (Prefix)

Ball Bearing BB TB (Prefix)

Oilite Bearing OB TA (Prefix)

Triple Plate CP S (Prefix)

Brass Pin BP BR (Suffix)

Stainless Steel Pin SP SSP (Suffix)

Set Screw in Barrel NRP NRP (Suffix)

Spun or Riveted Pin FRP FR/SP (Suffix)

Safety Stud SH SSF (Suffix)

Hospital Tip HT HT (Prefix)

Steeple Tip ST ST (Suffix)

Ball Tip BT BT (Suffix)

Round Corner RC RC (Prefix)

“Luma Sheen” LS AP (Finish)

“Luma-color” Black L1 D-4 (Finish)

“Luma-color” Dark Bronze L2 D-3 (Finish)

“Luma-color” Medium Bronze L3 D-2 (Finish)

Page 161: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross ReferenceLawrence Catalog Numbers

v April2003

Lawrence Brothers Numbers and McKINNEY Equivalent Numbers

Lawrence # McKINNEY # Lawrence # McKINNEY # Lawrence # McKINNEY #

CHP-1 EP-5

TPU-2 1/2 TA792TPU-2-1/2-A TA392SC2500 1400SC2514 1414SC2558 1458BB4101 TCA2714BB4101-32D TCA2314-32D

BB4101-A TCA2314BB4101WT TCA2798RB-BB4101 RBM-TA2714BB4105 TA2714 Slip-inBB4105-A TA2314 Slip-in4168 15024181 T2714

RC4181 RC27144181-A T23144181xRP T2705BB4301 TA27724381 T2772BB4601 TA27744681 T2774

BB4701 TA2771BB4901 TCA2714BB4901-32D TCA2314-32DBB4901-A TCA23144981 T27144981-32D T2314-32D

4981A T2314

BB4951 TCA3786BB4951-32D TCA3386-32DBB4951A TCA3386BB5151 T4A3786BB5151-32D T4A3386-32DRB-BB-5151 RBM-T4A3786BB5151-A T4A3386

BB5152 T4A3795BB5351 T4A3782BB5351-32D T4A3382-32DBB5351-A T4A3382BB5352 T4A3796BB5601 TA3774BB5601-A TA3374

BB5601-32D TA3374-32DBB5651 T4A3784BB5651-A T4A3384BB5652 T4A3789BB5751 T4A3781BB5751-32D T4A3381-32DBB5751-A T4A3381

BB5752 T4A3797BB6154A TA33297106 CSS98040 7038080 705

BB9101 TA714

BB9101-A TA314BB9151 TA786BB9151-32D TA786-32DBB9151-A TA386BB9152 TA7959181 T714BB9301 TA772

BB9301-A TA372BB9351 TA782BB9351-A TA382BB9352 TA796BB9601 TA774BB9601-A TA374BB9651 TA784

BB9651-A TA384BB9652 TA789BB9701 TA771BB9701-A TA371BB9751 TA781BB9751-A TA381BB9752 TA797

CEC CCCES CSSW ES

Suffix for Electric Hinges

Ball Bearings available upon request.

Page 162: Hinge Catalog

OP-1 R1-TOPES-1 DS-6DLS-1 DLS-8JB-1 MG-16BP-1 BP-10/BP-11DAP-3 EP-5BB98 T4A3384FBB108 TA3374FBB109 T4A3381FBB109-1/2 T4A3385FBB112 TA2372FBB113 T4A3382FBB138 T4A3784FBB163 T4A3782FBB167 TA2774F167 T2774FBB168 T4A3786/MPB68FBB169 T4A3781FBB169-1/2 T4A3785FBB171 TA2771F173 T2772FBB173 TA2772F179 T2714/MP79FBB179 TA2714/MPB79FBB179WT TA2798FBB179 Slip-in TA2714 Slip-inF191 T2314FBB191 TA2314/MPB91FBB191 Slip-in TA2314 Slip-in

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross ReferenceStanley Catalog Numbers

viApril2003

Suffix for Electric Hinges

Stanley Catalog Numbers and McKINNEY Equivalent Numbers

Stanley # McKINNEY # Stanley # McKINNEY # Stanley # McKINNEY #

Feature Stanley McKINNEY

Rust-Resistant Base K S (Prefix)

Solid Brass Ball Tips Solid Brass Ball Tips BT (Suffix)Steeple Tips Steeple Tips ST (Suffix)Hospital Tip HT HT (Prefix)Shear Resisting Stud SRS PSF (Suffix)Non Removable Pin NRP NRP (Suffix)Fast Spun Pin FSP SP (Suffix)

Security Stud Sec. St. SSF (Suffix)No Hole Prefix NH BLANKRaised Barrel RB RBM/RBS (Prefix)Slip-in Slip-in S1H Type 1

S1H Type 2 (Prefix)

Options

CB1920 TA774

CB1921 TA784CB1930 TA771CB1931 TA781CB1941 TA789CB1942 TA5789CB1948 TA795CB1949 TA5795

CB1951 TA797CB1959 TA796CB1960 TA314CB1961 TA386CB1967* TA393CB1968* TA392CB1969 TA5392

CB1970 TA372CB1971 TA382CB1980 TA374CB1981 TA384CB1990 TA371CB1991 TA3812060 1502

2063 1572

CE CC

CS CSES ESCS MMCExCS CCxCS

Note: *Available only in Bronze.

FBB199 T4A3386 / MPB99FBB211* TA793FBB212* TA792FBB213* TA5792FBB221* TA393FBB222* TA392FBB223* TA5392241 2714FBB248 TA2895FBB258 TA4895FBB264 T4A3789FBB266 T4A3797FBB268 T4A3795FBB269 T4A3796FBB274 T4A4789FBB278 T4A4795BB601-8" TB786-8"0700 T2731CB700 TA2731741 1400RD741 1414RD758 14581900 T714CB1900 TA714CB1901 TA786CB1907* TA793CB1908* TA792CB1909* TA5792CB1910 TA772CB1911 TA782

Page 163: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross ReferencePin & Barrel Continuous Hinges

vii April2003

Gallery, Markar, Roton, Select, Stanley Product Numbers and McKinney Equivalent Numbers

McKINNEY # ABH # Ives # Gallery # Markar # Roton # Stanley # Zero #

MCK-FM300 A500 700 951 FM-300 790-900 651 919STST

MCK-FS301 FS-301

MCK-FS302 A502 702 957 FS-302 657 916STST

MCK-HS303 A503 A503 954 HS-303 790-903

MCK-HM304 A504 HM-304 790-904 654 913STST

MCK-HG305 A505 705 952 HG-305 790-905 652 918STST

MCK-HG306 A506 955 HG-306 790-906 655

MCK-FS309 A511 A511 FS/SC-309 790-909

MCK-HG310 HG-310 790-910

MCK-HG311 A511 711 956 HG-311 653

MCK-HG315 A515 715 953 HG-315 790-915 653

MCK-FS321 FS-321

MCK-HG322 HG-322

MCK-HG323 HG-323

MCK-HG326 HG-326 790-326

MCK-FM327 FM-327

MCK-FM3500 FM-3500

MCK-FS3501 FM-3501

MCK-FS3502 FS-3502

MCK-HG3505 FS-3505

MCK-FM3700 600 CH-941 FM-200 641

MCK-FS3701 FS-201

MCK-FS3702 602 CH-947 FS-202 647

MCK-HS3703 HS-203

MCK-EG-308 EG-308

MCK-EG-C308 EG-C308

MCK-EG-T308 EG-T308

Page 164: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross ReferenceContinuous Aluminum Geared Hinge

viiiMay

2007

Heavy

Dut

yHeavy

Dut

y

Flus

hM

ount

Con

cealed

withSt

ops

Roton, Stanley, Markar, Select and Pemko Product Numbersand McKINNEY Equivalent Numbers

1 ⁄16

"In

setM

ount

withDoo

rLeafLip

MCK-12HD 83" Clear 780-112HD 661HD FM-2000 SL-11HDCL CFM 83SLFHD 9100DB-AMCK-12HD 83" Bronze 780-112HD 661HD FM-2000 SL-11HDBR DFM 83SLFHD 9100DB-DMCK-12HD 85" Clear 780-112HD 661HD SL-11HDCL CFM 85SLFHD 9100DB-AMCK-12HD 85" Bronze 780-112HD 661HD SL-11HDBR DFM 85SLFHD 9100DB-DMCK-12HD 95" Clear 780-112HD 661HD FM-2000 SL-11HDCL CFM 95SLFHD 9100DB-AMCK-12HD 95" Bronze 780-112HD 661HD FM-2000 SL-11HDBR DFM 95SLFHD 9100DB-BMCK-12HD 120" Clear 780-112HD 661HD FM-2000 SL-11HDCL CFM120SLFHD 9100DB-AMCK-12HD 120" Bronze 780-112HD 661HD FM-2000 SL-11HDBR DFM120SLFHD 9100DB-B

MCK-14HD 83" Clear 780-111HD SL-18HD CFM 83SLIHDMCK-14HD 83" Bronze 780-111HD SL-18HD DFM 83SLIHDMCK-14HD 85" Clear 780-111HD SL-18HD CFM 85SLIHDMCK-14HD 85" Bronze 780-111HD SL-18HD DFM 85SLIHDMCK-14HD 95" Clear 780-111HD SL-18HD CFM 95SLIHDMCK-14HD 95" Bronze 780-111HD SL-18HD DFM 95SLIHDMCK-14HD 120" Clear 780-111HD SL-18HD CFM 120SLIHDMCK-14HD 120" Bronze 780-111HD SL-18HD DFM 120SLIHD

McKinney # Roton # Stanley # Markar # Select # Pemko # Zero#

Page 165: Hinge Catalog

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

McKINNEY Hinge CatalogCross ReferenceContinuous Aluminum Geared Hinge

ix April2006

Heavy

Dut

yHeavy

Dut

yHeavy

Dut

yHeavy

Dut

y

1 ⁄16

"In

setM

ount

withDoo

rLeafLip

Roton, Stanley, Markar, Select and Pemko Product Numbersand McKINNEY Equivalent Numbers

FullSu

rface

HalfSu

rface

MCK-58HD 83" Clear 780-157HD 664HD FS-2002 SL-57A-HD CFS83CP HDMCK-58HD 83" Bronze 780-157HD 664HD FS-2002 SL-57D-HD DFS83CP HDMCK-58HD 85" Clear 780-157HD 664HD FS-2002 SL-57A-HD CFS85CP HDMCK-58HD 85" Bronze 780-157HD 664HD FS-2002 SL-57D-HD DFS85CP HDMCK-58HD 95" Clear 780-157HD 664HD FS-2002 SL-57A-HD CFS95CP HDMCK-58HD 95" Bronze 780-157HD 664HD FS-2002 SL-57D-HD DFS95CP HDMCK-25HD 83" Clear 780-224HD 662HD FM-2011 SL-24HDCL CFM 83HD 914DB-AMCK-25HD 83" Bronze 780-224HD 662HD FM-2011 SL-24HDBR DFM 83HD 914DB-DMCK-25HD 85" Clear 780-224HD 662HD SL-24HDCL CFM 85HD 914DB-AMCK-25HD 85" Bronze 780-224HD 662HD SL-24HDBR DFM 85HD 914DB-DMCK-25HD 95" Clear 780-224HD 662HD FM-2011 SL-24HDCL CFM 95HD 914DB-AMCK-25HD 95" Bronze 780-224HD 662HD FM-2011 SL-24HDBR DFM 95HD 914DB-DMCK-25HD 120" Clear 780-224HD 662HD FM-2011 SL-24HDCL CFM 120HD 914DB-AMCK-25HD 120" Bronze 780-224HD 662HD FM-2011 SL-24HDBR DFM 120HDMCK-22HD 83" Clear 780-210HD 665HD FS-2002 SL-21HDCL CFS83FDMCK-22HD 83" Bronze 780-210HD 665HD FS-2002 SL-21HDBR DFS83FDMCK-22HD 85" Clear 780-210HD 665HD SL-21HDCL CFS83FDMCK-22HD 85" Bronze 780-210HD 665HD SL-21HDBR DFS83FDMCK-22HD 95" Clear 780-210HD 665HD FS-2002 SL-21HDCL CFS83FDMCK-22HD 95" Bronze 780-210HD 665HD FS-2002 SL-21HDBR DFS83FDMCK-22HD 120" Clear 780-210HD 665HD FS-2002 SL-21HDCL CFS83FDMCK-22HD 120" Bronze 780-210HD 665HD FS-2002 SL-21HDBR DFS83FDMCK-54HD 83" Clear 780-053HD 663HD HS2003 SL-53HDCL CHS83HD 930DB-AMCK-54HD 83" Bronze 780-053HD 663HD HS2003 SL-53HDBR DHS83HD 930DB-AMCK-54HD 85" Clear 780-053HD 663HD SL-53HDCL CHS83HD 930DB-AMCK-54HD 85" Bronze 780-053HD 663HD SL-53HDBR DHS83HD 930DB-DMCK-54HD 95" Clear 780-053HD 663HD HS2003 SL-53HDCL CHS83HD 930DB-AMCK-54HD 95" Bronze 780-053HD 663HD HS2003 SL-53HDBR DHS83HD 930DB-DMCK-54HD 120" Clear 780-053HD 663HD HS2003 SL-53HDCL CHS83HDMCK-54HD 120" Bronze 780-053HD 663HD HS2003 SL-53HDBR DHS83HD

McKinney # Roton # Stanley # Markar # Select # Pemko # Zero#

Page 166: Hinge Catalog

McKINNEY Hinge CatalogComparative Finish Symbols

xApril2003

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

ANSI/BHMA Finish CodeBase Material

McKINNEY U.S. Description Lawrence Stanley Hager Bommer Steel Brass Bronze Stainless

P USP Primed for Painting P USP USP USP 600

D-4 US1D Dull Black US1D US1D US1B 601

2C US2C Zinc Plated, Commercial US2C US2C US2G 602

3 US3 Bright Brass 3 US3 US3 US3 632 605

4 US4 Dull Brass DB US4 US4 US4 633 606

5 US5 Dull Brass, Oxidized US5 US5 US5 638 609

7 US7 Brass, Nickel OxidizedBright Relieved

US7 US7 636 610

9 US9 Bright Bronze US9 US9 US9 637 611

10 US10 Dull Bronze 10 US10 US10 US10 639 612

10A US10A Antique Bronze, Lacquered 10A US10A US10A US10A10B US10B Antique Bronze, Oiled US10B US10B US10B 640 613

11 US11 Dull Bronze, Oxidized US11 US11 643 616

14 US14 Bright Nickel Plated US14 US14 US14 645 618 618

15 US15 Dull Nickel Plated US15 US15 US15 646 619 619

15A US15A Nickel Oxidized Relieved US15A US15A 647 620 620

17A US17A Half Polished Iron, Smooth US17A US17A US17A 648 621 621

20 US20 Statuary Bronze, Light US20 US20 649 623

20A US20A Statuary Bronze, Dark US20A US20A 650 624

26 US26 Bright Chromium 26 US26 US26 US26 651 625 625

26D US26D Dull Chromium 26D US26D US26D US26D 652 626 62632 US32 Polisehd Stainless Steel US32 US32 US32 629

32D US32D Dull Stainless Steel 32D US32D US32D US32D 630

3C Bright Brass with Clear Powder Coat

4C Dull Brass with Clear Powder Coat

15C Dull Nickel with Clear Powder Coat

AP Aluminum Lacquer LA LS FL2

D-2 CO-Laq, Medium DM L3

D-3 CO-Laq, Dark DD L2 FE3

D-4 CO-Laq, Black L1

GT Grey TonePB Powdered Beige

P-G Powdered Gold

P-W Powdered White DW 13P

Every effort is made by McKINNEY to furnish finishes which do comply with the U.S. Standard, however, we cannotguarantee that our finish will match other manufacturers finish. Where a special finish or a matched finish is required,a sample must be submitted with the order.

Page 167: Hinge Catalog

xi April2006

©McK

INNEYProductsCom

pany2006,2007

1-800-346-7707 • www.mckinneyhinge.com

35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75451, 452, 453 . . . . . . . . . . . . . . . . . . . . . . . . . .76703 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .951001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77-781400, 1414, 1458 . . . . . . . . . . . . . . . . . . . . . . .961502, 1552 . . . . . . . . . . . . . . . . . . . . . . . . . . . .711522 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .721572 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .733001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .824007-MRB, 4007-RB . . . . . . . . . . . . . . . . . . . .838007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .849001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7919001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80AdjustaScrew . . . . . . . . . . . . . . . . . . . . .121, 122ACC Option . . . . . . . . . . . . . . . . . . . . . . . . . .91BP-10, BP-11, BP-12 . . . . . . . . . . . . . . . . . . . .85CC Option . . . . . . . . . . . . . . . . . . . . . . . . . . . .90CS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74CSS-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86DLS-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88DS-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87EP-5J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43FirePins . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106H8007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84HS1001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81HTA2714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34HTA386 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30HTA386 - MSP . . . . . . . . . . . . . . . . . . . . . . . .44HTA714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29HTA786 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30ICHTB386 . . . . . . . . . . . . . . . . . .DiscontinuedIHTB386, IHTB786 . . . . . . . . . . . . . . . . . . . .31Interim Hinge . . . . . . . . . . . . . . . . . . . . . . . .100J3001 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82MCK-12HD . . . . . . . . . . . . . . . . . . . . . . . . . .107MCK-14HD . . . . . . . . . . . . . . . . . . . . . . . . . .108MCK-22HD . . . . . . . . . . . . . . . . . . . . . . . . . .109MCK-25HD . . . . . . . . . . . . . . . . . . . . . . . . . .110MCK-28HD . . . . . . . . . . . . . . . . . . . . . . . . . .111MCK-35HD . . . . . . . . . . . . . . . . . . . . . . . . . .115MCK-38HD . . . . . . . . . . . . . . . . . . . . . . . . . .115MCK-54HD . . . . . . . . . . . . . . . . . . . . . . . . . .112MCK-58HD . . . . . . . . . . . . . . . . . . . . . . . . . .113MCK-EG-308 . . . . . . . . . . . . . . . . . . . . . . . .149MCK-EG-C308 . . . . . . . . . . . . . . . . . . . . . . .150MCK-EG-T308 . . . . . . . . . . . . . . . . . . . . . . .151MCK FM3500 . . . . . . . . . . . . . . . . . . . . .139,140MCK FM3700 . . . . . . . . . . . . . . . . . . . . . . . .144MCK FM300 . . . . . . . . . . . . . . . . . . . . . . . . .123MCK FS301 . . . . . . . . . . . . . . . . . . . . . . . . . .124MCK FS309 . . . . . . . . . . . . . . . . . . . . . . . . . .130MCK FS321 . . . . . . . . . . . . . . . . . . . . . . . . . .134MCK FS3501 . . . . . . . . . . . . . . . . . . . . . . . . .141MCK FS3502 . . . . . . . . . . . . . . . . . . . . . . . . .142MCK FS3701 . . . . . . . . . . . . . . . . . . . . . . . . .145MCK FS3702 . . . . . . . . . . . . . . . . . . . . . . . . .146MCK FS302 . . . . . . . . . . . . . . . . . . . . . . . . . .125MCK HG305 . . . . . . . . . . . . . . . . . . . . . . . . .128MCK HG306 . . . . . . . . . . . . . . . . . . . . . . . . .129MCK HG310 . . . . . . . . . . . . . . . . . . . . . . . . .131

MCK HG311 . . . . . . . . . . . . . . . . . . . . . . . . .132MCK HG315 . . . . . . . . . . . . . . . . . . . . . . . . .113MCK HG322 . . . . . . . . . . . . . . . . . . . . . . . . .135MCK HG323 . . . . . . . . . . . . . . . . . . . . . . . . .136MCK HG326 . . . . . . . . . . . . . . . . . . . . . . . . .137MCK HG3505 . . . . . . . . . . . . . . . . . . . . . . . .143MCK HM304 . . . . . . . . . . . . . . . . . . . . . . . . .127MCK HS303 . . . . . . . . . . . . . . . . . . . . . . . . .126MCK HS3703 . . . . . . . . . . . . . . . . . . . . . . . .147MCK - WT-HD . . . . . . . . . . . . . . . . . . . . . . .114MG-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93MM Option . . . . . . . . . . . . . . . . . . . . . . . . . . .92MP79, MPB79 . . . . . . . . . . . . . . . . . . . . . . . . .40MPB68, MPB99 . . . . . . . . . . . . . . . . . . . . . . . .42MPB91 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41MT-SP-100 . . . . . . . . . . . . . . . . . . . . . . . . . .152PH-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94QC Option . . . . . . . . . . . . . . . . . . . . . . . . . . . .89RB-TA2314, RB-TA2714 . . . . . . . . . . . . . . . .98RB-T4A3386, RB-T4A3786 . . . . . . . . . . . . . .98SER Option . . . . . . . . . . . . . . . . . . . . . . . . . . .91Slip-In Hinge . . . . . . . . . . . . . . . . . . . . . . . . . .99T714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28T2314, T2714 . . . . . . . . . . . . . . . . . . . . . . . . .33T2731 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25T2772 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59T2774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49TA314 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29TA371 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67TA372 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57TA374 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51TA381 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65TA382 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58TA384 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52TA386 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30TA391 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45TA392 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46TA393 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47TA394 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48TA714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29TA771 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67TA772 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57TA774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51TA781 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65TA782 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58TA784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52TA786 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30TA789 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54TA791 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45TA792 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46TA793 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47TA794 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48TA795 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32TA796 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62TA797 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69TA2314 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34TA2371 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68TA2372 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60A2395 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38TA2398 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

TA2714 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34TA2731 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26TA2771 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68TA2772 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60TA2774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50TA2798 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35TA2895 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38TA3331 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26TA3350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27TA3374 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50TA3383 . . . . . . . . . . . . . . . . . . . . .Discontinued

TA3750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27TA3784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51TA5391 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45TA5392 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46TA5393 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47TA5394 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48TA5791 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45TA5792 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46TA5793 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47TA5794 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48TCA2314, TCA2714 . . . . . . . . . . . . . . . . . . .34TCA2771 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68TCA2772 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60TCA2774 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50TCA3374 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50TCA3381 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66TCA3382 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61TCA3384 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53TCA3386 . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37TCA3781 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66TCA3782 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61TCA3784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53TCA3786 . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37T4A3381 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66T4A3382 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61T4A3384 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53T4A3386 . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37T4A3395 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39T4A3781 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66T4A3782 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61T4A3784 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53T4A3786 . . . . . . . . . . . . . . . . . . . . . . . . .36 - 37T4A3789 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55T4A3795 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39T4A3796 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63T4A3797 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70T4A4795 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39TA4895 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38T6A3386, T6A3786 . . . . . . . . . . . . . . . . . . . .36TCA2371 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68TCA2372 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60TCA4395 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

General Information

Index

Aluminum Continuous Gear Hinge . . . . . . . .102Beveled Edge . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Non-Removable Pins . . . . . . . . . . . . . . . . . . . . .7Raised Barrel . . . . . . . . . . . . . . . . . . . . . . . . . . .13Round Corner . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Rust Resistant Base . . . . . . . . . . . . . . . . . . . . . .23Safety Stud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Stainless & Steel Pin & Barrel HingeInformation . . . . . . . . . . . . . . . . . . . . . . . . . . .117UL & NFPA Reference Information . . . . . . . .17

Prison Safety Feature . . . . . . . . . . . . . . . . . . . . . .5Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 21Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Page 168: Hinge Catalog

McKINNEY Products Company • 225 Episcopal Road • Berlin • CT 06037 • Phone: 800.346.7707 • Fax: 800.541.1073ASSA ABLOY Door Security Solutions Canada • 160 Four Valley Drive • Vaughan, Ontario • L4K 4T9 • Tel: 800.461.3007 • Fax: 905.738.2478 • www.assaabloy.ca

Founded in 1864, McKINNEY Products Company is a market leader in the manufacture of quality architecturalgrade hinges including security hinges, and continuous hinges for the builders’ hardware industry.

Copyright © 2006-2010, McKinney Products Company, an ASSA ABLOY Group company. All rights reserved.

Reproduction in whole or in part without the express written permission of McKinney Products Company is prohibited.

ASSA ABLOY is the global leader in door opening solutions, dedicated tosatisfying end-user needs for security, safety and convenience. 51101-6/07