Page I

HINIKER 1700 SHREDDER

5/16

PART NUMBER 79201955 Rev. F

HINIKER1700 SHREDDER

PARTS BOOK

SECTION 1 PTO SHAFTSSECTION 2 GEARBOXSECTION 3 HITCH ASSEMBLIESSECTION 4 BODY ASSEMBLIESSECTION 5 COMPONENT PARTSSECTION 6 OPTIONAL EQUIPMENT

PARTSPart Number 79201955 Rev. F May 2016 Parts Books/Hiniker/79201955RevF

It is the policy of Hiniker Company to constantly improve its products whenever it is practical to do so.

Hiniker Company must therefore reserve the right to redesign or change its equipment or component parts thereof without incurring the obligation to install or furnish such changes on the equipment previously delivered.

INSTRUCTIONS FOR ORDERING PARTS

1. The reference numbers (Ref. No.) in the illustrations correspond to the same refer-ence numbers (Ref. No.) in the description list. An assembly having a part number can be ordered. All other parts must be ordered individually. The quantity in the (Qty.) col-umn is the number of parts used in this area of the machine. The term “A/R” for number required indicates “as required” where the quantity may vary. Order all parts by their part number and description. Do not use the reference number (Ref. No.).

2. All references to left and right, front and rear apply to the machine as viewed from the rear of the machine, facing forward in the direction of travel.

3. Always mention the identification number of the model and serial numbers found on the name plate of the unit on which the part is to be used. Much delay and confusion can be avoided when correct numbers are specified on parts order and correspondence.

HINIKER COMPANY58766 240th St.P.O. BOX 3407

MANKATO, MN 56002-3407 USAPhone: (800) 433-5620

Fax: (800) 637-3991e-mail: hiniker@hiniker.com

Page 1

HINIKER 1700 SHREDDER

5/16

SEC

1

SECTION 1PTO SHAFTS

PAGE 2 3-POINT HITCH PTO 1 3/8-21 (YELLOW) SHIELDSPAGE 3 3-POINT HITCH PTO 1 3/8-21 (BLACK) SHIELDSPAGE 4 3-POINT HITCH PTO 1 3/4-20 (YELLOW) SHIELDSPAGE 5 3-POINT HITCH PTO 1 3/4-20 (BLACK) SHIELDSPAGE 6 1 3/8-21 1000 RPM CV PTO (YELLOW SHIELDS)PAGE 7 1 3/4-20 1000 RPM CV PTO (YELLOW SHIELDS)PAGE 8 1 3/8-21 1000 RPM CV PTO (BLACK SHIELDS)PAGE 9 1 3/4-20 1000 RPM CV PTO (BLACK SHIELDS)PAGE 10 OVERRUNNING CLUTCH, 1000 RPM

Page 2

HINIKER 1700 SHREDDER

5/16

3 POINT HITCH PTO 1 3/8-21(YELLOW SHIELDS)

DWG. NO. 2509

SEC

1

520-02157 3-Point PTO Shaft Assembly

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

10

520-03158520-03128520-03124520-03159520-03118520-03134520-03129520-03137520-03135520-03138

Yoke 1 3/8 - 21 SplineCross & Bearing KitSpring Pin 10 x 90Inboard YokeOverrunning ClutchShield Cone 7 RibBearing RingChainScrewOuter Decal

1211122121

111213141516171819

520-03139520-03136520-03140520-03165520-03162520-03163520-03164520-03141520-03142520-02157

Inner DecalSupport BearingGrease ZerkInner ProfileInboard Yoke, Outer Profile And SleeveOuter Shield TubeInner Shield TubeCollar KitCollar KitComplete PTO Shaft Assembly

111111111

Page 3

HINIKER 1700 SHREDDER

5/16

SEC

13-POINT HITCH PTO 1 3/8-21

(BLACK SHIELDS)

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

1011

520-0315879203639520-03124520-03159520-0311852003235520-03129520-03137520-03135520-03138520-03139

Yoke 1 3/8 - 21 SplineCross & Bearing KitSpring Pin 10 x 90Inboard YokeOverrunning Clutch (See Section 1 Page 10)Shield Cone 7 RibBearing RingChainScrewOuter DecalInner Decal

12211221211

121314151617181920

520-03136520-031407920409979204115520-03163520-03164520-03141520-031427920340379204096

Support BearingGrease ZerkInner ProfileInboard Yoke OuterOuter Shield TubeInner Shield TubeCollar KitCollar KitReinforcing CollarComplete PTO Shaft Assembly

111111002

DWG. NO. 2509A79204096 3-Point PTO Shaft Assembly

Page 4

HINIKER 1700 SHREDDER

5/16

SEC

13 POINT HITCH PTO 1 3/4-20

(YELLOW SHIELDS)

DWG. NO. 2515

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

10

520-03170520-03128520-03124520-03159520-03165520-03127520-03172520-03118520-03134520-03173

Yoke 1 3/4-20 SplineCross & Bearing KitSpring PinInboard YokeInner ProfileInboard YokeOuter ProfileOverrunning ClutchShield ConeOuter Shield Tube

1221111121

111213141516171819

520-03174520-03129520-03137520-03135520-03138520-03139520-03136520-03140520-03142

Inner Shield TubeBearing RingChainScrewOuter DecalInner DecalSupport BearingGrease ZerkCollar Kit

121211112

Page 5

HINIKER 1700 SHREDDER

5/16

SEC

13-POINT HITCH PTO 1 3/4-20

(BLACK SHIELDS)

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

1011

520-0317079203639520-03124520-0315979204099520-0312779204100520-03118520-03235520-03173520-03174

Yoke 1 3/4-20 SplineCross & Bearing KitSpring PinInboard YokeInner ProfileInboard YokeOuter ProfileOverrunning Clutch (See Section 1 Page 10)Shield ConeOuter Shield TubeInner Shield Tube

12211111211

121314151617181920

520-03129520-03137520-03135520-03138520-03139520-03136520-03140520-031427920340379204095

Bearing RingChainScrewDanger DecalDanger DecalSupport BearingGrease ZerkCollar KitReinforcing CollarComplete 3 Point PTO Assembly

212111125

DWG. NO. 2515A79204095 3-Point PTO Shaft Assembly

Page 6

HINIKER 1700 SHREDDER

5/16

1 3/8-21 1000 RPM CV PTO (YELLOW SHIELDS)

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

10111213

520-03119520-03120520-03121520-03122520-03123520-03133520-03125520-03124520-03135520-03138520-03130520-03129520-03132

Yoke 1 3/8-21 SplineDouble YokeGrease ZerkInboard YokeCross & Bearing KitShield Cone 3 RibInner ProfileSpring PinScrewOuter DecalOuter ShieldBearing RingCV Cone & Bearing Assembly

1111211281121

14151617181920212223242526

520-03141520-03136520-03139520-03131520-03140520-03137520-03134520-03126520-03127520-03118520-03128520-03142520-03115

Collar KitSupport BearingInner DecalInner ShieldGrease ZerkSafety ChainShield Cone 7 RibProfile & Sleeve WeldmentInboard YokeOverrunning ClutchCross & Bearing KitCollar KitComplete Front Half, 1 3/8-21 CV Assembly

111111111111

DWG. NO. 2518

SEC

1

Page 7

HINIKER 1700 SHREDDER

5/16

1 3/4-20 1000 RPM CV PTO (YELLOW SHIELDS)

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

10111213

520-03143520-03120520-03121520-03122520-03123520-03132520-03144520-03133520-03145520-03138520-03125520-03129520-03142

Yoke 1 3/4-20 SplineDouble YokeGrease ZerkInboard YokeCross & Bearing KitCv Cone & Bearing KitInner ProfileShield Cone, 3 RibOuter ShieldOuter DecalScrewBearing RingCollar Kit

1111211111822

141516171819202122232425

520-03124520-03136520-03139520-03177520-03140520-03137520-03134520-03176520-03127520-03118520-03128520-03117

Spring PinSupport BearingInner DecalInner ShieldGrease ZerkSafety ChainShield Cone 7 RibProfile & Sleeve WeldmentInboard YokeOverrunning ClutchCross & Bearing KitComplete Front Half 1 3/4-20 CV Assembly

21111111111

DWG. NO. 2671

SEC

1

Page 8

HINIKER 1700 SHREDDER

5/16

1 3/8-21 1000 RPM CV PTO (BLACK SHIELDS)SEC

1

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

101112131415

520-03119520-03120520-0312152003230520-03123520-03124520-03144520-03176520-03127520-0311852003243520-0312952003246520032475200323352003244

Yoke, 1 3/8-21 SplineDouble YokeGrease ZerkInboard Yoke S4Cross & Bearing KitSpring Pin 10 x 90Inner ProfileProfile & Sleeve WeldmentInboard Yoke S5Overrunning ClutchCross & Bearing KitBearing RingOut Shield Tube OVLIn Shield Tube RoundCV Cone & Bearing AssemblyCV Cone & Bearing Assembly (With Flex Net)

1111111111121111

16

17181920212223242526272829

520032345200324552003235520-03135520-03136520-03137520-03138520-03139520-03140520032365200323752003242520-03142520-0314179203403

Shield Cone 4 RibFlex Net & Guard AssemblyShield Cone 7 RibScrewSupport BearingSafety ChainOuter DecalInner DecalGrease ZerkLubrication DecalCross & Bearing KitSpring Pin 10 x 75Collar Kit (In Item 10)Collar Kit (In Item 1)Reinforcing Collar

111

1011111111111

DWG. NO. 593679202278 PTO 1 3/8-21 GKN 395564

Page 9

HINIKER 1700 SHREDDER

5/16

1 3/4-20 1000 RPM CV PTO (BLACK SHIELDS)SEC

1

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

101112131415

520-03143520-03120520-0312152003230520-03123520-03124520-03144520-03176520-03127520-0311852003243520-0312952003246520032475200323352003244

Yoke, 1 3/4-20 SplineDouble YokeGrease ZerkInboard Yoke S4Cross & Bearing KitSpring Pin 10 x 90Inner ProfileProfile & Sleeve WeldmentInboard Yoke S5Overrunning ClutchCross & Bearing KitBearing RingOut Shield Tube OvalInn Shield Tube RoundCV Cone & Bearing AssemblyCV Cone & Bearing Assembly (With Flex Net)

1111111111121111

16

171819202122232425262728

520032345200324552003235520-03135520-03136520-03137520-03138520-03139520-03140520032365200323752003242520-0314279203403

Shield Cone 4 RibFlex Net & Guard AssemblyShield Cone 7 RibScrewSupport BearingSafety ChainOuter DecalInner DecalGrease ZerkLubrication DecalCross & Bearing KitSpring Pin 10 x 75Collar KitReinforcing Collar

111

101111111121

DWG. NO. 593779202277 PTO 1 3/4-20 GKN 396073

Page 10

HINIKER 1700 SHREDDER

5/16

OVERRUNNING CLUTCH 1000 RPM

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1234

520-03146520-03147520-03148520-03149

Clutch HousingKeyLeaf SpringSupporting Ring

1222

5678

520-03150520-03151520-03121520-03142

Retaining RingHub, 1 3/4 - 20 SplineGrease ZerkCollar Kit

1111

DWG. NO. 2512

SEC

1

520-03118 Overrunning Clutch

Page 1

HINIKER 1700 SHREDDER

5/16

SEC

2SECTION 2GEARBOX

PAGE 2 GEARBOX ASSEMBLY, 1000 RPM

Page 2

HINIKER 1700 SHREDDER

5/16

GEARBOX ASSEMBLY, 1000 RPM

DWG. NO. 2505C

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

10

400-17205400-172065010648850106489601-05002601-02075601-05001601-03003650-06056702-05093

Casting (Tapped Holes)Casting (Thru Holes)Pinion Shaft/Gear (Replaces 15, 16, 17, 20) S/N-103Cross Shaft/GearBearing Cup (Large) #3720Bearing Cone (Large) #3782Bearing Cup (Small) #25520Bearing Cone (Small) #25581Seal (1 3/4 Shaft)Retaining Ring (1 3/4 Shaft)

1111113231

11121314151617181920

950-011-032203-51156203-51074203-50308501-06483517-11099702-53219601-0200179201412702-05093

Socket Head Cap Screw 3/8-16 x 2 1/4Plug, 1/2 NPT Hex Socket HeadBushing, 1/2 NPT - 1/8 NPTPressure ReliefPinion ShaftGear 1:1 Ratio3/8 Square x 1.45 Long KeysBearing Cone 625580Plain Plug 1/4 NPTRetaining Ring (1 3/4 Shaft)

12111122111

SEC

2

51700216 1000 RPM Gearbox Assembly

Page 1

HINIKER 1700 SHREDDER

5/16

SECTION 3HITCH ASSEMBLIES

PAGE 2 TRAIL HITCH ASSEMBLYPAGE 3 3 - POINT HITCH ASSEMBLY

SEC

3

Page 2

HINIKER 1700 SHREDDER

5/16

TRAIL HITCH ASSEMBLY

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456

035-420657920099379201772031-06459952-001-009951-001-011

Cotter Pin 1/4 x 1 3/4Hitch PinBar LevelHex Head Cap Screw 1-8 x 3 Gr. 5Lock Washer 1 InchHex Nut 1-8

422222

789

1011

7150517279201776850-001-28585501787850-001-305

Decal, “Warning”Hitch AssemblyTape Yellow ReflectorDecal, ‘Caution”Tape Red Reflector

11111

DWG. NO. 3174

SEC

3

79201775 Trail Hitch Assembly

Page 3

HINIKER 1700 SHREDDER

5/16

3-POINT HITCH ASSEMBLY

SEC

3

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

101112

792033262501031979203173117-010-008117-010-009875-001-123890-001-00979200965952-002-0107920099079200964035-42064

3-Point Hitch WeldmentKlik PinLower Pin AssemblySmall SpacerLarger SpacerTop Link PinSpacerSpacer CollarFlat Washer 1 InchPTO Chain AssemblyCenter Link PinCotter Pin 1/4 x 1 1/2

142222122114

1314151617181920212223

7920088079200881034-05172950-001-147792009937920108379201081953-002-021953-005-001850-001-305850-001-28579203325

Top LinkLinkStover Lock Nut 5/8-11Hex Head Cap Screw 5/8-11 x 2 1/2 Gr. 5Lower Trail Hitch PinStand Mount WeldmentStand Tube WeldmentClevis Pin 5/8 x 3 1/2Cotter Pin .120 x 2 3/8Tape Red Reflector (Side Opposite)Tape Yellow Reflector Complete 3-Point Hitch Assembly

12221111111

DWG. NO. 2494A79203325 3-Point Hitch Assembly

Page 1

HINIKER 1700 SHREDDER

5/16

SEC

4

SECTION 4BODY ASSEMBLIES

PAGE 2 12 FT. & 15 FT. BODY ASSEMBLYPAGE 4 18 & 20 FT. BODY ASSEMBLYPAGE 6 ROTOR BEARING 2” SHAFT

Page 2

HINIKER 1700 SHREDDER

5/16

12 FT. & 15 FT. BODY ASSEMBLY

DWG. NO. 3175A

SEC

4

Page 3

HINIKER 1700 SHREDDER

5/16

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

1011

12131415161718192021222324252627282930313233343536373839404142

434445464748495051

000-20179000-20192000-2406379202316516-15001515-1800851599032000-64011000-65186000-65223000-6541179200976950-003-054950-001-013034-05168034-05170034-051727920177879202088035-60063203-51251203-51254400-27038400-340745170021679203223

6040052460400525203-5000379201397710-05332710-0533379202087715-03174850-001-305850-001-285792030237150412671505171715041317150413679201811792017947920411271505168720-023997920121379200825792031577920083679200860792008667920091279200911

1 3/8 Machinery BushingAdapter Fitting 1/4-28 To 1/8 NPTLock NutGrease Hose“HC” V-Belt Set Of 2Sheave, 2 Groove, Type “6”Sheave, 2 Groove, Type “1”Shield PlateSpring AnchorThreaded HandleFlipper Shield Rod (Used On 12 Ft. Shredders Only)Flipper Shield Rod (Used On 15 Ft. Shredders Only)Carriage Bolt 3/8-16 x 3/4 SS Gr. 5Hex Head Cap Screw 3/8-16 x 3 Gr. 8Uni-Torque Lock Nut 3/8-16 Uni-Torque Lock Nut 1/2-13Uni-Torque Lock Nut 5/8-11 LH Line ShieldShield Spacer 1/16” ThickWoodruff Key 1/2 x 2 3/445° Elbow Lube Line 1/4-28 To 1/8 NPT45° Elbow 1/8 NPT To 1/8 NPTQ.D. Hub, Type “SF”, 2 BoreTubular Mount JackGear Box Assembly, 1000 RPM2” Spherical BearingFlange Bearing, 2” Shaft (See Page 6, Sec. 4)Relube Flange WO/FittingRelube Flange W/FittingGrease Zerk 1/4-28RH Hose Shield (Shown)WasherWasherShield Spacer 1/8” ThickLift Here DecalRed Reflective StripAmber Reflective StripDecal Spring InstructionImportant DecalWarning DecalDanger DecalImportant DecalInside Shield (Used On 12 Ft Shredders)Inside Shield (15 Ft Shredders) (W/Reducer Ends)Inside Shield (15 Ft Shredders) (WO/Reducer Ends)“Hiniker” Decal3/8 Cable ClampRockshaft Repair Kit 15 Ft.Anti-Wrap RingAnti-Wrap Shield WeldmentSplined Coupler W/FittingsBearing SupportTake Up Bar12’ Solid Line Shaft (Used On 12 Ft. Shredders)15’ Solid Line Shaft (Used On 15 Ft. Shredders)

2A/R

44222

A/R2422622

3231

A/R4

A/RA/R

411

A/RA/RA/RA/R

31

A/RA/RA/R

232212122226416222222

5253

545556

57585960616263646566676869707172

73

747576777879808182838485868788899091929394

79200920792009237920337779201398792017587920181079201793792037187920095679200967953-001-00279201779952-003-006952-004-067952-001-0047920178071504129951-005-003950-003-028950-002-01479201120950-002-010950-002-00979201808792018847920319879203206792032087920180979201883792032047920320579203207792010377920186179201860950-001-024953-001-010950-001-301950-001-112950-001-111000-690967150516971505167715051707150413371504132520-0313879203259950-002-01379203951955-001-0107920396979203966

Shield RodBottom Cover (7” Wide Drive Shield)Bottom Cover (8” Wide Drive Shield)LH Hose ShieldBearing SupportOutside Shield (Used On 12 Ft. Shredders)Inside Shield (15 Ft Shredders) (W/Reducer Ends)Inside Shield (15 Ft Shredders) (WO/Reducer Ends)Idler AssemblyLower Hitch Pin1/8 x 1 Square Cut Cotter PinRH Line ShieldFlat Washer 3/8 SAEFlat Washer 1/2 HardenedLock Washer 1/2 InchCylinder LugCaution DecalMac Lock Nut 3/8-16Carriage Bolt 1/2-13 x 1 1/4 Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1 1/4 Shield BumperHex Head Flanged Whiz Lock Bolt 3/8-16 x 1 1/2 Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1LH 12’ Cylinder Assembly Cup KnifeLH 12’ Cylinder Assembly Side SliceLH 15’ Cylinder Assembly Cup KnifeLH 15’ Cylinder Assembly Side SliceLH 15’ Cylinder Assembly Cup Knife & Side SliceRH 12’ Cylinder Assembly Cup KnifeRH 12’ Cylinder Assembly Side SliceRH 15’ Cylinder Assembly Cup KnifeRH 15’ Cylinder Assembly Side SliceRH 15’ Cylinder Assembly Cup Knife & Side SliceShield AssemblyRH Cover AssemblyLH Cover Assembly (Not Shown)Hex Head Cap Screw 5/8-11 x 2 1/2 Gr. 8Square Cut Cotter Pin 1/4 x 1 1/2Hex Head Cap Screw 1/2-13 x 4 1/4 Gr. 5Hex Head Cap Screw 1/2-13 x 2 Gr. 5Hex Head Cap Screw 1/2-13 x 1 1/4 Gr. 5Hose Carrier (Used On Trail Shredders)Warning DecalDecal 1700Warning DecalImportant DecalCaution DecalOuter DecalGrease DecalHex Head Flanged Whiz Lock Bolt 1/2-13 x 1 1/2External Snap Ring 2” Heavy DutyGrease Fitting 1/8-27 x 90°Chain Coupling Weldment (Can Replace Item 48)#60 Double Chain

22212222226185

A/R11

48201744

121111111111111344

A/RA/R

1222112

A/R42242

SEC

4

Page 4

HINIKER 1700 SHREDDER

5/16

18 & 20 FT BODY ASSEMBLY

DWG. NO.3176A

SEC

4

Page 5

HINIKER 1700 SHREDDER

5/16

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

1011

12131415161718192021222324252627282930313233343536373839404142

434445464748495051

52

000-20179000-20192000-2406379202316000-25168000-2851179201781000-64011000-65186000-6522379201071000-65627950-003-054950-001-013034-05168034-05170034-05172953-001-002953-001-010035-60063203-51251203-51254400-27039400-340745170021679203223

6040052460400525203-5000379201397710-05332710-05333520-03138715-03174850-001-305850-001-2857920302371504126715051717150413171504136792018187904120792018207920411371505168720-02399792019287920082579203157792008367920086079200866792009137920091479200920

1 3/8 Machinery BushingAdapter Fitting 1/4-28 To 1/8 NPTLock NutGrease Hose“HC” V-Belt Set Of 3Drive Shaft SheaveCylinder SheaveShield PlateSpring AnchorThreaded Handle18’ Flipper Shield Rod (Used On 18 Ft. Shredder Only)Rod (Used On 20 Ft. Shredder Only)Carriage Bolt 3/8-16 x 3/4 SS Gr. 5Hex Head Cap Screw 3/8-16 x 3 Gr. 8Uni-Torque Lock Nut 3/8-16Uni-Torque Lock Nut 1/2-13Uni-Torque Lock Nut 5/8-11Square Cut Cotter Pin, 1/8 x 1Square Cut Cotter Pin, 1/4 x 1 1/2Woodruff Key 1/2 x 2 3/445° Elbow Lube Line 1/4-28 To 1/8 NPT45° Elbow 1/8 NPT To 1/8 NPTQ.D. Hub, Type “E”, 2 BoreTubular Mount JackGear Box Assembly, 1000 RPM2” Spherical BearingFlange Bearing, 2” Shaft (See Page 6, Sec. 4)Relube Flange WO/FittingRelube Flange W/FittingGrease Zerk 1/4-28RH Hose Shield (Shown)WasherWasherOuter DecalLift Here DecalRed Reflective StripAmber Reflective StripDecal Spring InstructionImportant DecalWarning DecalDanger DecalImportant DecalInside Shield (Used On 18 Ft Shredders)Inside Shield (18 Ft Shredders) (WO/Reducers)Inside Shield (20 Ft Shredders) (W/Reducers)Inside Shield (20 Ft Shredders) (WO/Reducers)“Hiniker” Decal3/8 Cable Clamp18 Ft. Shield Plate (Used On 18 Ft. Shredder Only)Anti-Wrap RingAnti-Wrap Shield WeldmentSplined Coupler W/FittingsBearing SupportTake Up Bar18’ Solid Line Shaft20’ Solid Line ShaftShield Rod

2A/R44222

A/R2422622

326644

A/RA/R411

A/RA/RA/RA/R51

A/RA/R223321212222264262222222

53

545556

57585960616263646566676869707172

73

74757677787980818283848586878889

909192939495

79200923792033777920139879201758792018177920350479201819792041147920095679200967952-003-00679201779952-004-067952-001-0047920208879201780951-005-003950-003-028950-002-014950-002-01079201120950-002-009950-001-024792018157920188079203209792032147920321279201816792018797920319779203213792032117920103779201861792018607920208779201778950-001-301950-001-112950-001-111000-69096715051697150516771505170715041337150413271504129792012187920121679203259950-002-013955-001-010792039517920396979203966

Bottom Cover (7” Wide Drive Shield)Bottom Cover (8” Wide Drive Shield)LH Hose ShieldBearing SupportOutside Shield (Used On 18 Ft. Shredders)Outside Shield (18 Ft. Shredders) (WO/Reducers)Outside Shield (20 Ft. Shredders) (W/Reducer)Outside Shield (20 Ft. Shredders) (WO/Reducer)Idler AssemblyLower Hitch PinSAE Washer 3/8 InchRH Line ShieldFlat Washer 1/2 Inch HardenedLock Washer 1/2 InchShield Spacer 1/16” ThickCylinder LugMac Lock Nut 3/8-16Carriage Bolt 1/2-13 x 1 1/4 Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1 1/4Hex Head Flanged Whiz Lock Bolt 3/8-16 x 1 1/2Shield BumperHex Head Flanged Whiz Lock Bolt 3/8-16 x 1Hex Head Cap Screw 5/8-11 x 2 1/2 Gr. 8LH 18’ Cylinder Assembly Cup KnifeLH 18’ Cylinder Assembly Side SliceLH 20’ Cylinder Assembly Cup KnifeLH 20’ Cylinder Assembly Side SliceLH 20’ Cylinder Assembly Cup Knife & Side SliceRH 18’ Cylinder Assembly Cup KnifeRH 18’ Cylinder Assembly Side SliceRH 20’ Cylinder Assembly Cup KnifeRH 20’ Cylinder Assembly Side SliceRH 20’ Cylinder Assembly Cup Knife & Side SliceShield AssemblyRH Cover AssemblyLH Cover Assembly (Not Shown)Shield Spacer 1/8” ThickLH Line ShieldHex Head Cap Screw 1/2-13 x 4 1/4 Gr. 5Hex Head Cap Screw 1/2-13 x 2 Gr. 5Hex Head Cap Screw 1/2-13 x 1 1/4 Gr. 5Hose Carrier (Used On Trail Shredders)Warning DecalDecal 1700Warning DecalImportant DecalCaution DecalCaution DecalRockshaft Repair Kit 18 FtRockshaft Repair Kit 20 FtGrease DecalHex Head Flanged Whiz Lock Bolt 1/2-13 x 1 1/2Grease Fitting 1/8-27 x 90°External Snap Ring 2” Heavy DutyChain Coupling Weldment (Can Replace Item 48)#60 Double Chain

2222222222815

A/RA/R2

48A/R1744

1261111111111111

A/R14

A/RA/R122211111

A/R42242

SEC

4

Page 6

HINIKER 1700 SHREDDER

5/16

SEC

4

DWG. NO.6735

Page 1

HINIKER 1700 SHREDDER

5/16

SEC

5

SECTION 5COMPONENT PARTS

PAGE 2 KNIFE & ROTOR ASSEMBLYPAGE 3 IDLER ASSEMBLYPAGE 3 SMV SIGN ASSEMBLYPAGE 4 TIRE, RIM, & WHEEL LEG ASSEMBLY

Page 2

HINIKER 1700 SHREDDER

5/16

4

6

2

3

5

3

4

5

9

85

7

1

10

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456

000-65227000-65142000-65141030-16139034-05170000-65143

Knife HangerD-RingKnife PivotCarriage Bolt 1/2 x 3 1/4 Gr. 5Lock NutSide Knife

A/RA/RA/RA/RA/RA/R

789

10

030-16132000-6514479203812792038117920143179203349

Carriage Bolt 1/2 x 1 1/2 Gr. 5Square Ring3” Cup Knife Assembly (Includes Items 1, 5, 7, 8, 10)3” Cup Knife Assembly Hard Surfaced (Includes Items 1, 5, 7, 8, 10)Cup KnifeCup Knife Hard Surfaced

A/RA/RA/RA/RA/RA/R

DWG. NO. 3185

KNIFE & ROTOR ASSEMBLY CUP KNIFE & SIDE SLICER

QUANTITY ONLY CUP KNIFE OR SIDE SLICER * QUANTITY COMBINATIONCUP KNIFE & SIDE SLICER

REF. NO. 12’ 15’ 18’ 20’ 15’ 18’ 20’123456789

10

48484848969648484848

72727272

14414472727272

72727272

14414472727272

96969696

19219296969696

48247272

1204848484848

48247272

1204848484848

64329696

1606464646464

* Note: See operators manual (assembly section) for proper knife arrangement.

SEC

5

Page 3

HINIKER 1700 SHREDDER

5/16

IDLER ASSEMBLY

DWG. NO. 2514

2

5

3

4

6

1

SMV SIGN ASSEMBLY

DWG. NO. 2521

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1234

400-22083 850-001-354031-10599951-001-002

MountSMV EmblemMachine Screw #10-24 x 1/2 Slotted Round HeadHex Nut #10-24

1122

56

033-22007 715-03056 790-41218

Lock Washer #10Caution DecalComplete SMV Sign Assembly

21

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456

7920095551599031725-03047031-06365951-005-037033-12013

Idler Weldment8” Idler PulleyExtension SpringHex Head Cap Screw 3/4 -10 x 5 Gr. 5Lock Nut 3/4-10 2-WayFlat Washer 3/4 Inch

111111

789

10

400-10466951-001-009952-001-0067920231079200956

SpacerHex Nut 3/4-10Lock Washer 3/4 InchSpacer 5/16 x 3/4 ConduitComplete Idler Assembly

2111 S

EC

5

79200956 Idler Assembly

790-41218 SMV And Mount Assembly

Page 4

HINIKER 1700 SHREDDER

5/16

DWG. NO. 5607

TIRE, RIM, & WHEEL LEG ASSEMBLY

SEC

5

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

101112

7920321079203647951-001-008952-001-005950-001-023850-001-164850-001-154850-003-053955-001-001950-011-006850-001-153802-000-007

Wheel Leg Weldment (See Drawing Above)Clamp Plate WeldmentHex Nut 5/8-11 Lock Washer 5/8 Hex Head Cap Screw 5/8-11 x 2 Gr. 5Triple Lip SealCone JL69349Hub W/Wear Sleeve (Includes 16, 17, 18)Grease Fitting 1/8-27 NPT Wheel Bolt 1/2-20 x 1 Cone LM67048Flat Washer 7/8 Inch

116661111611

13141516171819

2021

951-005-002953-001-017850-001-155850-001-159850-001-555850-001-158850-001-8287920336880504793805-001-154850-002-66979203649

Slotted Nut 7/8-14Square Cut Cotter Pin 5/32 x 1 1/2 Dust CapRear Cup JL 69310Wear SleeveFront Cup LM 670105” x 15 Rim - 6 Bolt Black (Not Part Of Assembly)8” x 15 Rim 6-Bolt (Not Part Of Assembly)Tire Valve (Not Part Of Assembly)7.6 x 15 Tire 8 Ply9.5L x 15 Tire 8 PlyWheel Leg Assembly (Includes Items 1-18)

11111111111

Page 1

HINIKER 1700 SHREDDER

5/16

SEC

6

SECTION 6OPTIONAL EQUIPMENT

PAGE 2 RATCHET JACK ASSEMBLYPAGE 2 GRASS DIVIDERPAGE 3 MANUAL END TRANSPORT KITPAGE 4 MANUAL END TRANSPORT HUB & SPINDLE ASSEMBLYPAGE 4 HYDRAULIC CYLINDER STOP BLOCK SETPAGE 5 HYDRAULIC END TRANSPORT (20’ ONLY)PAGE 6 PTO SHAFT HOLDERPAGE 6 SKID SHOESPAGE 7 SAFETY LIGHTING FIELD USE ONLYPAGE 7 SAFETY LIGHTING END TRANSPORT/FIELD USEPAGE 8 HYDRAULIC LIFT KIT 18’ AND 20’PAGE 8 HYDRAULIC LIFT KIT 15’PAGE 9 HYDRAULIC CYLINDER 2 1/2 X 8PAGE 9 HYDRAULIC CYLINDER 3 X 8

Page 2

HINIKER 1700 SHREDDER

5/16

RACHET JACK ASSEMBLY

DWG. NO. 2502

GRASS DIVIDER

DWG. NO. 3172

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

12

79201851 950-002-013

Grass Divider WeldmentHex Head Flanged Lock Bolt 1/2-13 x 1 1/2

11

34

031-06208 951-005-055

Hex Head Cap Screw 1/2-13 x 2 1/4 Gr.5Mac Lock Nut 1/2-13

12

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1 000-04067 Rachet Jack Assembly 1

SEC

6

79201854 Grass Divider Assembly

Page 3

HINIKER 1700 SHREDDER

5/16

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1234567

792010407920188779200977850-001-309000-20255950-001-246950-001-166

Transport Tongue AssemblyFront Transport Mount WeldmentRear Transport WeldmentHitch Pin AssemblyClevis Pin AssemblyHex Head Cap Screw 1/2-13 x 7 1/2 Gr. 5Hex Head Cap Screw 3/4-10 x 2 Gr. 5

1112123

89

10111213

034-05170034-05173952-003-00479201044850-001-828805-001-154

UNI-Torque Lock Nut 1/2-13 UNI-Torque Lock Nut 3/4-10 SAE Flat Washer 1/2 InchEnd Transport Spindle Assembly5 x 15 Rim - 6 Bolt7.60 x 15 Tire 8 Ply

23422

A/R

DWG. NO. 3186

MANUAL END TRANSPORT KITFOR USE ON 12’, 15’, 18’

AND(20’ SN 1740-0090-103 AND LOWER)(20’ SN 1741-0244-103 AND LOWER)(20’ SN 1742-0047-103 AND LOWER)

SEC

6

1751 End Transport Kit

Page 4

HINIKER 1700 SHREDDER

5/16

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1234567

79201028850-001-164850-001-154850-003-053955-001-001950-011-006850-001-153

Spindle End TransportTriple Lip SealCone JL69349Hub W/Wear Sleeve (Includes Item 12)Grease Fitting 1/8-27 NPT Wheel Bolt 1/2-20 x 1Cone LM67048

1111161

89

101112

802-000-007951-005-002953-001-017850-001-155850-001-55579201044

Washer 7/8 Slotted Nut 7/8-14Square Cut Cotter Pin 5/32 x 1 1/2 Dust CapWear SleeveComplete Spindle Assembly

11111

DWG. NO. 2519

MANUAL END TRANSPORT HUB & SPINDLE ASSEMBLY

SEC

6

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1 79203414 Hydraulic Cylinder Stop Block Set 1

DWG. NO. 6857

HYDRAULIC CYLINDER STOP BLOCK SET

Page 5

HINIKER 1700 SHREDDER

5/16

SEC

6

HYDRAULIC END TRANSPORT KITFOR USE ON 20’ ONLY

(20’ SN 1740-0090-104 AND UP)(20’ SN 1741-0244-104 AND UP)(20’ SN 1742-0047-104 AND UP)

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

123456789

10111213141516171819202122

79202985792026697920335179202987792033887920297879203378792029887920236879203419957-021-001955-001-002956-007-023957-029-00179202989956-003-001921-001-144956-008-03662301179202990950-001-16579202967

Rear Wheel Leg AssemblyFront Wheel Leg AssemblyTire & Rim Assembly 9.5L-15 x 12 PlyJack Clevis Weldment End Trans Hitch W/Decal AssemblyRear Transport Pivot WeldmentFront WeldmentBracket, Pivot ClampHydraulic Cylinder 3 x 8 (See Sec 6 Pg 9) LionCylinder StopHose Assembly 1/4 x 54”Grease Fitting 1/4-28Bulkhead Fitting-Tee 9/16 JICHose Assembly 1/4 x 120”Rockshaft BearingStraight Adapter 9/16 To 3/4,.297 ID14” Plastic Cable TieMale Hydraulic 3/4 ORB Connector ISOLynch Pin 5/16 x 2 3/4Rockshaft Bearing CapHex Head Cap Screw 5/8-11 x 7 1/2 Gr. 5Hitch Pin

1121111222422264825233

23242526272829303132333435363738394041424344

950-001-152060756034-05173950-001-097951-005-03679202681950-001-092951-005-051950-001-125950-001-023950-001-166034-05170921-001-490921-001-48779203524400-11027030-1604185501557953-001-007792034447920343679202686

Hex Head Cap Screw 3/4-10 x 6 Gr. 5Lock Nut 5/8-11 Nylon InsertLock Nut 3/4-10 Gr. B Uni-TorqueHex Head Cap Screw 5/16-18 x 2 1/2 Gr. 5Lock Nut 5/16-18 Mac LocPinHex Head Cap Screw 3/8-16 x 1 3/4 Gr. 5Lock Nut 3/8-16, 2 WayHex Head Cap Screw 1/2-13 x 1 1/2 Gr. 5Hex Head Cap Screw 5/8-11 x 2 Gr. 5Hex Head Cap Screw 3/4-10 x 2 Gr. 5Lock Nut 1/2 Gr. B StoverGreen Cable TieRed Cable TieTubular Mount Jack 10” TravelBracketCarriage Bolt 5/16-18 x 3/4 Gr. 5Cylinder PinCotter Pin 3/16 x 1 1/2 EP Square CutCompression SpringLatchCylinder Stop

1544824442348811224222

DWG. NO. 6858For Hub Bearing Info See Sec 5 Pg 479202993 Hydraulic End Transport Kit

Page 6

HINIKER 1700 SHREDDER

5/16

SKID PLATE KIT

DWG. NO. 5941

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

12

79202281950-001-029

Skid WeldmentHex Head Cap Screw 3/4-10 x 1 3/4 Gr. 5

28

3 951-005-097 Lock Nut 3/4-10 Mac-Lock 8

79202306 Skid Plate Kit

SEC

6

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

12345678

950-003-012951-005-051952-001-004952-004-067951-005-0367920274079202638031-06110

Carriage Bolt 3/8-16 x 2 1/4 Gr. 5Lock Nut 3/8-16 2-WayLock Washer 1/2 InchFlat Washer 1/2 InchLock Nut 5/16-18 Mac LocPTO HolderMount PlateHex Head Cap Screw 3/8-16 x 2 1/4 Gr. 5

13221112

9101112131415

792026397920343479203444950-001-200950-001-13579202739953-005-001

PTO HolderHose StopCompression SpringHex Head Cap Screw 5/16-18 x 1 1/4 Gr. 5Hex Head Cap Screw 1/2-13 x 2 3/4 Gr. 5PinHair Pin

1111211

DWG. NO. 6382

PTO HOLDER

Page 7

HINIKER 1700 SHREDDER

5/16

SAFETY LIGHT FIELD USE ONLY

DWG. NO. 5940

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1234

36100000361000013880902879202294

Light, Implement, LH AssemblyLight, Implement, RH AssemblyHarness, LightingLight Bracket

1112

567

367-001-014031-06006951-005-089

Cable Tie, Black 8 InchHex Head Cap Screw 1/4-20 x 1 Gr. 5Hex Nut 1/4-20 2-Way

1288

SEC

6

END TRANSPORT/FIELD USE SAFETY LIGHTING PACKAGE

DWG. NO. 6506

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

12345

7920312479203125400-1102738809035367-001-014

Light Assembly LeftLight Assembly RightBracketLighting HarnessCable Tie, Black 8 Inch

1111

20

6789

030-1604179203129951-005-03679203128

Carriage Bolt 5/16-18 x 3/4 Gr. 5Wire HolderMac Lock Nut 5/16-18Long Light Bar

6161

79203126 Safety Light Package

Page 8

HINIKER 1700 SHREDDER

5/16

SEC

6

HYDRAULIC LIFT KIT 18’ AND 20’

DWG. NO. 5943

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1234

79202351956-003-001957-022-014956-007-023

Hydraulic Cylinder 2 1/2 x 8 (See Sec 6 Pg 9)Straight Adapter 9/16 M To 3/4 M .297IDHose Assembly 1/4 x 126”Fitting-Tee Bulkhead 9/16 JIC

2442

567

957-028-011956-008-036921-001-144

Hose Assembly 3/8 x 150”Connector ISO Male Hydraulic 3/4 ORB14” Plastic Cable Tie

228

79202349 Hydraulic Lift Kit 18’ and 20’

HYDRAULIC LIFT KIT 15’

DWG. NO. 6531

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

12

79202368956-005-001

3 x 8 Cylinder Assembly90° Elbow

12

34

957-004-006 957-004-007

Hose Assembly 3/8 x 156” Hose Assembly 3/8 x 172”

11

79201616 Hydraulic Cylinder Package

Page 9

HINIKER 1700 SHREDDER

5/16

SEC

6

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1 79202366 Seal Kit 1

2 1/2 X 8 CYLINDER

DWG. NO. 656779202351 2 1/2 x 8 Cylinder

REF.NO.

PARTNUMBER DESCRIPTION QTY. REF.

NO.PART

NUMBER DESCRIPTION QTY.

1 79202380 Seal Kit 1

3 X 8 CYLINDER

DWG. NO. 594979202368 3 x 8 Cylinder