HYDRAULIC INTEGRATED CIRCUITS Delta Power · PDF fileHYDRAULIC INTEGRATED CIRCUITS Delta Power Company ... HYDRAULIC INTEGRATED CIRCUITS Delta Power Company ... Rectifier Circuit

HYDRAULIC INTEGRATED CIRCUITS Delta Power Company 4484 Boeing Drive - Rockford, IL 61109

WARNING: The specifications/application data shown in our catalogs and data sheets are intended only as a general guide for the product described (herein). Any specific application should not be undertaken without independent study, evaluation, and testing for suitability.

Phone: (815) 397-6628 Fax: (815) 397-2526 E-mail: [email protected]

SECTION/Description Pages

Mini Series Single Pilot Operated Check Valve 554 Mini Series Double Pilot Operated Check Valve 556 Power Series Single Pilot Operated Check Valve 558 Power Series Double Pilot Operated Check Valve 560 Delta Series Single Pilot Operated Check Valve 562 Delta Series Double Pilot Operated Check Valve 564 Delta Series Double Pilot Operated Check Valve with Thermal Relief 566 Super Series Single Pilot Operated Check Valve 568 Super Series Double Pilot Operated Check Valve 570 Continued Next Page…

Page 552




SECTION/Description Pages Pre-Engineered Circuit, Option Model A 572 Load Holding Solenoid Operated, RV w/Adj. Press. Comp. Flow Control, RV w/Fixed Press. Comp. Flow Control, Unloading w/flow control,Lift Circuit w/RV, RV w/Flow Control, Unloading w/ Fixed Press. Comp. Flow Control Speed Control

Pre-Engineered Circuit, Option Model B 574 Lift, Check, & Dump. Startup Circuit, Lift, Check & Dump w/RV

Pre-Engineered Circuit, Option Model C 576 Dual RV, Dump, Flow Divider, Motor Speed Control, Selector, Hydrostatic (Anti-Cav)

Pre-Engineered Circuit, Option Model D 578 NC Poppet Valve, Single RV, Needle Flow Control, Flow Control w/Free Flow Check, NO Spool valve, Crossover RV

Pre-Engineered Circuit, Option Model E 580 Adj. Flow Control NC Poppet Dual Speed Circuit, Adj. Press. Comp. Flow Control NC Poppet Dual Speed Circuit, Press. Comp. Flow Control & Check Valve, Adj. Press. Comp. Flow Control NO Poppet Dual Speed Circuit, Adj. Flow Control NO Poppet Dual Speed Circuit, Press. Comp Flow Control and Check, Adj. Flow Control NC Spool Valve Dual Speed Circuit

Pre-Engineered Circuit, Option Model F 582 Dual Sequence Valve Manifold

Pre-Engineered Circuit, Option Model G 584 Rectifier Circuit

Pre-Engineered Circuit, Option Model H 586 4w3p Open Center, 4w3p Closed Center

Pre-Engineered Circuit, Option Model I 588 3way valve, Manual Lift Check & Dump, NC Poppet Valve and RV, Lift Check & Dump, Pump Check & RV, Needle Flow Control & Check, NO Poppet & Check, NO Poppet & RV

Pre-Engineered Circuit, Option Model J 590 4w3p Tandem Center

Pre-Engineered Circuit, Option Model K 592 2 NC Poppet Valves, NO Poppet Valve & Needle Valve, 2 NC Poppet Valves, NC Poppet Valve & Adj.Press. Comp Flow Control

Pre-Engineered Circuit, Option Model L 594 Dual Counterbalance Circuit

Pre-Engineered Circuit, Option Model M 596 Single 4:1 PO Check Circuit

Pre-Engineered Circuit, Option Model N (Banjo Bolt) 598 Velocity Fuse, NC Poppet Valve, Adj, Press, Comp. Flow Control, Needle Valve, NO Spool Valve

Pre-Engineered Circuit, Option Model O 600 Single Counterbalance Circuit

Pre-Engineered Circuit, Option Model P 602 Lift Circuit w/Needle Valve & RV, Lift Circuit w/Press. Comp Flow Control & RV, Lift Circuit w/Bypass & Needle Valve, Lift Circuit w/Bypass & Press. Comp Flow Control

Pre-Engineered Circuit, Option Model Q 604 Dual 3 way Valves

Pre-Engineered Circuit, Option Model R 606 Single RV Circuit

Pre-Engineered Circuit, Option Model S 608 Crossover Relief, Mower Breakaway, Unloading & RV

Pre-Engineered Circuit, Option Model TA 610 Pump Unloading Circuit

Page 553




MS-POC Single Pilot Operated Check Valve

DESCRIPTION 7 size, 5/8-18 thread, “Mini” series, pilot operated check valve. OPERATION The MS-POC allows flow to pass from (V) to (C) and blocks flow from (C) to (V). When pilot pressure is applied to pilot port the valve allows flow from (C) to (V). The valve has a 6.7:1 pilot ratio, so at least .149 of the load pressure is required at the (PILOT) port to open the flow passage to allow flow from ports (C). The check is spring-biased at 50 psi (3.4 bar) to assure holding in static or no-load conditions. FEATURES

TYPICAL SCHEMATIC

• Hardened internal parts for long life. • Anodized aluminum body for corrosion

protection.

HYDRAULIC SYMBOL

VALVE SPECIFICATIONS Nominal Flow 5 GPM (19 LPM) Rated Operating Pressure 3000 PSI (207 bar) Typical Internal Leakage (150 SSU) 0-5 drops/min

Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal Pilot Ratio 6.7:1 Media Operating Temperature Range -40° to 250° F (-40° to 120° C)

Weight .7 lbs. (.30 kg) Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Torque Requirements 15 ft-lbs (20.3 Nm)

Cartridge Crack Pressure 50 PSI (3.4 bar)

Page 554




DIMENSIONS

ORDERING INFORMATION MS-POC - -

OPTIONS BODIES

Buna Standard B N 1/4 NPTF Ports Viton Standard V S #4 SAE Ports

Page 555




PS-POC Single Pilot Operated Check Valve

DESCRIPTION 8 size, 3/4-16 thread, “Power” series, pilot operated check valve. OPERATION The PS-POC allows flow to pass from (V) to (C) and blocks flow from (C) to (V). When pilot pressure is applied to pilot port the valve allows flow from (C) to (V). The valve has a 4:1 pilot ratio, so at least .250 of the load pressure is required at the (PILOT) port to open the flow passage to allow flow from ports (C). The check is spring-biased at 50 psi (3.4 bar) to assure holding in static or no-load conditions. FEATURES

TYPICAL SCHEMATIC

• Hardened internal parts for long life.

• Anodized aluminum body for corrosive protection.

HYDRAULIC SYMBOL


Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal Pilot Ratio 4:1 Media Operating Temperature Range -40° to 250° F (-40° to 120° C)

Weight 1.0 lbs. (.45 kg) Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Torque Requirements 25 ft-lbs (34 Nm)


Page 556




DIMENSIONS

ORDERING INFORMATION PS-POC - -

OPTIONS BODIES


Page 557




DS-POC Single Pilot Operated Check Valve

DESCRIPTION 10 size, 7/8-14 thread, “Delta” series, pilot operated check valve. OPERATION The DS-POC allows flow to pass from (V) to (C) and blocks flow from (C) to (V). When pilot pressure is applied to pilot port the valve allows flow from (C) to (V). The valve has a 4:1 pilot ratio, so at least .250 of the load pressure is required at the (PILOT) port to open the flow passage to allow flow from ports (C). The check is spring-biased at 90 psi (6.2 bar) to assure holding in static or no-load conditions. FEATURES

TYPICAL SCHEMATIC



HYDRAULIC SYMBOL

VALVE SPECIFICATIONS

Nominal Flow 15 GPM (57 LPM) Rated Operating Pressure 3500 PSI (241 bar) Typical Internal Leakage (150 SSU) 0-5 drops/min

Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal Pilot Ratio 4:1 Media Operating Temperature Range -40° to 250° F (-40° to 120° C)

Weight 1.1 lbs. (.50 kg) Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Torque Requirements 30 ft-lbs (40.6 Nm)


Page 558




DIMENSIONS

ORDERING INFORMATION DS-POC - -

OPTIONS BODIES


Page 559




SS-POC Single Pilot Operated Check Valve

DESCRIPTION 16 size, 1 5/16-12 thread, “Super” series, pilot operated check valve. OPERATION The SS-POC allows flow to pass from (V) to (C) and blocks flow from (C) to (V). When pilot pressure is applied to pilot port the valve allows flow from (C) to (V). The valve has a 3.7:1 pilot ratio, so at least .270 of the load pressure is required at the (PILOT) port to open the flow passage to allow flow from ports (C). The check is spring-biased at 50 psi (3.4 bar) to assure holding in static or no-load conditions. FEATURES

TYPICAL SCHEMATIC



HYDRAULIC SYMBOL


Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal Pilot Ratio 3.7 : 1 Media Operating Temperature Range -40° to 250° F (-40° to 120° C)

Weight 4.3 lbs. (2.0 kg) Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Torque Requirements 90 ft-lbs (122 Nm)


Page 560




DIMENSIONS

ORDERING INFORMATION SS-POC - -

OPTIONS BODIES

Buna Standard B S #12 SAE Ports Viton Standard V

Page 561




MD-POC Double Pilot Operated Check Valve

DESCRIPTION 7 size, 5/8-18 thread, “Mini” series, double pilot operated check valve. OPERATION The MD-POC allows flow to pass from (V1) to (C1) and (V2) to (C2). The valve blocks flow from (C1) to (V1) and from (C2) to (V2). Blocked flow is released when pilot pressure is applied to port opposite valve (V1) and/or port (V2) accordingly. The valve has a 6.7:1 pilot ratio, so at least .141 of the load pressure at port (C1) or (C2) is required at the pilot lines (ports (V2) or (V1) respectively to open the flow passage to allow flow from ports (C1) or (C2) respectively. The check is spring-biased at 50 psi (3.4 bar) to assure holding in static or no-load conditions. FEATURES

TYPICAL SCHEMATIC


• Anodized aluminum body for corrosion protection.

HYDRAULIC SYMBOL



Weight .92 lbs. (.42kg) Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Torque Requirements 15 ft-lbs (20.3 Nm)


Page 562




DIMENSIONS

ORDERING INFORMATION MD-POC - -

OPTIONS BODIES


ROCKFORD, ILLINOIS U.S.A.

DELTA POWERHYDRAULIC CO.

SAE PORTS SHOWNMTG. HOLES ARE .28 DIA.NOTE: DIMENSIONS IN BRACKETS ARE MILLIMETERSO-RINGS ARE STANDARD ON PISTON ASSEMBLYCHECK VALVE USED IS A MA-CVA

V2

V1

C2

C1

.63[16.0]

.19 [4.8]

1.07[27.2]

1.08[27.3]

1.31[33.3]

2.00[50.8]

.31 [8.0]

.54[13.6]

1.16 [29.5]

2.31[58.7]

.63 [15.9]

1.25 [31.8]

.45 [11.4]

.46 [11.6]

3.38 [85.9]

Page 563




PD-POC Double Pilot Operated Check Valve

DESCRIPTION 8 size, 3/4-16 thread, “Power” series, double pilot operated check valve. OPERATION The PD-POC allows flow to pass from (V1) to (C1) and (V2) to (C2). The valve blocks flow from (C1) to (V1) and from (C2) to (V2). Blocked flow is released when pilot pressure is applied to port opposite valve (V1) and/or port (V2) accordingly. The valve has a 4:1 pilot ratio, so at least .250 of the load pressure at port (C1) or (C2) is required at the pilot lines (ports (V2) or (V1) respectively to open the flow passage to allow flow from ports (C1) or (C2) respectively. The check is spring-biased at 50 psi (3.4 bar) to assure holding in static or no-load conditions. FEATURES

TYPICAL SCHEMATIC


• Anodized aluminum body for corrosion protection.

HYDRAULIC SYMBOL


Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal Pilot Ratio 4 : 1 Media Operating Temperature Range -40° to 250° F (-40° to 120° C)

Weight 1.2 lbs. (.53kg) Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Torque Requirements 25 ft-lbs (34 Nm)


Page 564




DIMENSIONS

ORDERING INFORMATION PD-POC - -

OPTIONS BODIES


Page 565




DD-POC Double Pilot Operated Check Valve

DESCRIPTION 10 size, 7/8-14 thread, “Delta” series, double pilot operated check valve. OPERATION The DD-POC allows flow to pass from (V1) to (C1) and (V2) to (C2). The valve blocks flow from (C1) to (V1) and from (C2) to (V2). Blocked flow is released when pilot pressure is applied to port opposite valve (V1) and/or port (V2) accordingly. The valve has a 4:1 pilot ratio, so at least .250 of the load pressure at port (C1) or (C2) is required at the pilot lines (ports (V2) or (V1) respectively to open the flow passage to allow flow from ports (C1) or (C2) respectively. The check is spring-biased at 90 psi (6.2 bar) to assure holding in static or no-load conditions. FEATURES

TYPICAL SCHEMATIC



HYDRAULIC SYMBOL





Page 566




DIMENSIONS

ORDERING INFORMATION DD-POC - -

OPTIONS BODIES


Page 567




SD-POC Double Pilot Operated Check Valve

DESCRIPTION 16 size, 1 5/16-12 thread, “Super” series, double pilot operated check valve. OPERATION The SD-POC allows flow to pass from (V1) to (C1) and (V2) to (C2). The valve blocks flow from (C1) to (V1) and from (C2) to (V2). Blocked flow is released when pilot pressure is applied to port opposite valve (V1) and/or port (V2) accordingly. The valve has a 3.7:1 pilot ratio, so at least .267 of the load pressure at port (C1) or (C2) is required at the pilot lines (ports (V2) or (V1) respectively to open the flow passage to allow flow from ports (C1) or (C2) respectively. The check is spring-biased at 50 psi (3.4 bar) to assure holding in static or no-load conditions.

FEATURES TYPICAL SCHEMATIC



HYDRAULIC SYMBOL



Weight 6.0 lbs. (2.7kg) Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Torque Requirements 90 ft-lbs (122 Nm)


Page 568




DIMENSIONS

ORDERING INFORMATION SD-POC - -

OPTIONS BODIES

Buna Standard B S #12 SAE Ports Viton Standard V

Page 569




DD-POT Double Pilot Operated Check Valve W/Thermal Relief Valve

DESCRIPTION 10 size, 7/8-14 thread, “Delta” series, double pilot operated check valve with thermal relief valve. OPERATION The DD-POT allows flow to pass from (V1) to (C1) and (V2) to (C2). The valve blocks flow from (C1) to (V1) and from (C2) to (V2). Blocked flow is released when pilot pressure is applied to port opposite valve (V1) and/or port (V2) accordingly. Also “C2 port is protected by thermal relief. The valve has a 4:1 pilot ratio, so at least .250 of the load pressure at port (C1) or (C2) is required at the pilot lines (ports (V2) or (V1) respectively to open the flow passage to allow flow from ports (C1) or (C2) respectively. The check is spring-biased at 90 psi (6.2 bar) to assure holding in static or no-load conditions. FEATURES

TYPICAL SCHEMATIC



HYDRAULIC SYMBOL





Page 570




DIMENSIONS

ORDERING INFORMATION DD-POT - -

OPTIONS BODIES


Page 571




Pre-Engineered Circuit, Option Model A*

DESCRIPTION Pre-engineered circuit, option model A* OPERATION

See options chart for specific operation

VALVE SPECIFICATIONS Nominal Flow See Options Chart for Flow Range

Rated Operating Pressure See Options Chart for Pressure Range

Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal

Media Operating Temperature Range -40° to 250° F (-40° to 120° C)

Operating Fluid Media General Purpose Hydraulic Fluid BODY WEIGHT: .83 lbs. [.37 kg.] Cartridge Size Delta Series 7/8-14 Thread.

Cartridge Torque Requirements 30 ft-lbs (40.6 Nm)

Coil Torque Nut Requirements 4-6 ft-lbs. (5.4-8.1 Nm)

DIMENSIONS

Page 572




OPTIONS CHART

ORDERING INFORMATION - - - - - VALVE 2

CIRCUITS FLOW PRESSURE AA OPTIONS 01 .5-1 GPM 02 20-500 PSI

AB Buna Standard 00 02 1-2 GPM 15 200-1500 PSI AC Viton Standard V0 VOLTAGE 04 2-4 GPM 30 1500-3000 PSI AD Manual Override 0M 06 6 VDC 08 4/8 GPM 40 2500-4000 PSI AE 12 12 VDC FLOW CONTROL RELIEF VALVE AF 24 24 VDC AG 36 36 VDC AH 48 48 VDC 25 25 VAC VALVE 1

11 120 VAC FLOW PRESSURE “D” COIL TERMINATION 22 220 VAC 01 .5-1 GPM 02 20-500 PSI (All DC Except as Noted) 44 440 VAC 02 1-2 GPM 15 200-1500 PSI 04 2-4 GPM 30 1500-3000 PSI DL Double Lead HC DIN 43650 (Hirschman) – (AC & DC) 08 4-8 GPM 40 2500-4000 PSI DT Deutsch on Leads DT04-2P CL Conduit Lead – (AC Only) FLOW CONTROL RELIEF VALVE ML Metri-Pack on Leads DI Deutsch – Integral DT04-2P PL Packard on Leads IMMERSION PROOF “ D” TYPE WL Weatherpack on Leads IA “I” Coil AMP Superseal - Integral SS Single Spade ID “I” Coil Deutsch – Integral DT04-2P FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTORY DS Double Spade IJ “I” Coil AMP Jr. Timer - Integral

IM “I” Coil Metri-Pack – Integral

Approximate Coil Weight: .74 lbs (.33 kg.)

Page 573




Pre-Engineered Circuit, Option Model B*

DESCRIPTION Pre-engineered circuit, option model B* OPERATION


VALVE SPECIFICATIONS Nominal Flow 12 GPM (48 LPM)

Rated Operating Pressure 3500 PSI (241 bar) Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal


Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Size Delta Series 7/8-14 Thread.

BODY WEIGHT: 1.2 lbs. [.54 kg.] Cartridge Torque Requirements 30 ft-lbs (40.6 Nm)


DIMENSIONS

Page 574




OPTIONS CHART

ORDERING INFORMATION - - - - -

VALVE 2 FLOW PRESSURE

CIRCUITS BA OPTIONS 01 .5-1 GPM 02 20-500 PSI BB Buna Standard 00 02 1-2 GPM 15 200-1500 PSI BC Viton Standard V0 VOLTAGE 04 2-4 GPM 30 1500-3000 PSI Manual Override 0M 06 6 VDC 08 4/8 GPM 40 2500-4000 PSI 12 12 VDC FLOW CONTROL RELIEF VALVE 24 24 VDC 36 36 VDC 48 48 VDC 25 25 VAC VALVE 1

11 120 VAC FLOW PRESSURE “D” COIL TERMINATION 22 220 VAC 01 .5-1 GPM 02 20-500 PSI (All DC Except as Noted) 44 440 VAC 02 1-2 GPM 15 200-1500 PSI 04 2-4 GPM 30 1500-3000 PSI DL Double Lead HC DIN 43650 (Hirschman) – (AC & DC) 08 4-8 GPM 40 2500-4000 PSI DT Deutsch on Leads DT04-2P CL Conduit Lead – (AC Only) FLOW CONTROL RELIEF VALVE ML Metri-Pack on Leads DI Deutsch – Integral DT04-2P PL Packard on Leads IMMERSION PROOF “D” TYPE WL Weatherpack on Leads IA “I” Coil AMP Superseal - Integral SS Single Spade ID “I” Coil Deutsch – Integral DT04-2P FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTORY DS Double Spade IJ “I” Coil AMP Jr. Timer - Integral



Page 575




Pre-Engineered Circuit, Option Model C*

DESCRIPTION Pre-engineered circuit, option model C* OPERATION



Rated Operating Pressure See Options Chart for Pressure Ranges






DIMENSIONS

Page 576




OPTIONS CHART

ORDERING INFORMATION - - - - - VALVE 2 FLOW PRESSURE

CIRCUITS CA OPTIONS 01 .5-1 GPM 02 20-500 PSI CB Buna Standard 00 02 1-2 GPM 15 200-1500 PSI CC Viton Standard V0 VOLTAGE 04 2-4 GPM 30 1500-3000 PSI CD Manual Override 0M 06 6 VDC 08 4/8 GPM 40 2500-4000 PSI CE 12 12 VDC FLOW CONTROL RELIEF VALVE CF 24 24 VDC 36 36 VDC 48 48 VDC 25 25 VAC VALVE 1




Page 577




Pre-Engineered Circuit, Option Model D*

DESCRIPTION Pre-engineered circuit, option model D* OPERATION



Rated Operating Pressure See Options Chart for Pressure Ranges






DIMENSIONS

Page 578




OPTIONS CHART

ORDERING INFORMATION - - - -

CIRCUITS VALVE 1 DA OPTIONS FLOW PRESSURE

DB Buna Standard 00 01 .5-1 GPM 02 20-500 PSI DC Viton Standard V0 VOLTAGE 02 1-2 GPM 15 200-1500 PSI DD Manual Override 0M 06 6 VDC 04 2-4 GPM 30 1500-3000 PSI DE 12 12 VDC 08 4-8 GPM 40 2500-4000 PSI DF 24 24 VDC FLOW CONTROL RELIEF VALVE 36 36 VDC 48 48 VDC FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTORY 25 25 VAC

11 120 VAC “D” COIL TERMINATION 22 220 VAC (All DC Except as Noted) 44 440 VAC DL Double Lead HC DIN 43650 (Hirschman) – (AC & DC) DT Deutsch on Leads DT04-2P CL Conduit Lead – (AC Only) ML Metri-Pack on Leads DI Deutsch – Integral DT04-2P PL Packard on Leads IMMERSION PROOF “D” TYPE WL Weatherpack on Leads IA “I” Coil AMP Superseal - Integral SS Single Spade ID “I” Coil Deutsch – Integral DT04-2P DS Double Spade IJ “I” Coil AMP Jr. Timer - Integral



Page 579




Pre-Engineered Circuit, Option Model E*

DESCRIPTION Pre-engineered circuit, option model E* OPERATION






BODY WEIGHT: .75 lbs. [.34 kg.] Cartridge Torque Requirements 30 ft-lbs (40.6 Nm)


DIMENSIONS

Page 580




OPTIONS CHART

CIRCUIT EA

CIRCUIT EB

CIRCUIT ED

CIRCUIT EE

CIRCUIT EC

A

B

A

B

B

A

A

B

B

A

DUAL SPEED CIRCUI T

PRESSURE COM P. FLOW CONTRO L & CHECK VALVE

12 GPM NOMINA L

8 GPM NOMINAL

8 GPM NOMINAL

12 GPM NOMINAL

8 GPM NOMINAL

2

1

NVB

S2A

VALVE 1

VALVE 2

B

A

FCA

S2A

1

2

CVAFCA

1

2

NVB

S2C

1

2

FCA

S2C

1

2

DUAL SPEED CIRCUI T

DUAL SPEED CIRCUI T

DUAL SPEED CIRCUI T

12

1

2

ADJUSTABLE RELIEF & CHECK VALVE

10 GPM NOMINA L

2

1

B

CIRCUIT EF

A

CVARVA2 1

12

1

2

1

2

B7 GPM NOMINAL CIRCUIT EG

1NVA

2 2S2H

A

DUAL SPEED CIRCUI T

1


CIRCUITS EA OPTIONS 01 .5-1 GPM 02 20-500 PSI EB Buna Standard 00 02 1-2 GPM 15 200-1500 PSI EC Viton Standard V0 VOLTAGE 04 2-4 GPM 30 1500-3000 PSI ED Manual Override 0M 06 6 VDC 08 4/8 GPM 40 2500-4000 PSI EE 12 12 VDC FLOW CONTROL RELIEF VALVE EF 24 24 VDC EG 36 36 VDC 48 48 VDC 25 25 VAC VALVE 1




Page 581




Pre-Engineered Circuit, Option Model F*

DESCRIPTION Pre-engineered circuit, option model F* OPERATION See typical schematic for specific operation.


Rated Operating Pressure 50-1500 PSI (4-103 bar) Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal


Operating Fluid Media General Purpose Hydraulic Fluid BODY WEIGHT: 1.5 lbs. [.68 kg.] Cartridge Size Delta Series 7/8-14 Thread.


DIMENSIONS

Page 582




TYPICAL SCHEMATIC

ORDERING INFORMATION - - - VALVE 2 PRESSURE

CIRCUITS FA OPTIONS 04 50-425 PSI Buna Standard 00 15 400-1500 PSI Viton Standard V0

VALVE 1 PRESSURE 04 50-425 15 400-1500 PSI

FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTORY

C1A C1B C2A C2B

VBVADUAL SEQUENCE VALVE MANIFOLDAUTOMATICALLY CONTROLS THESEQUENCING OF TWO CYLINDERS.

PWE

PWE

CVACVA

CIRCUIT FA

Page 583




Pre-Engineered Circuit, Option Model G*

DESCRIPTION Pre-engineered circuit, option model G* OPERATION

See typical schematic for specific operation





Cartridge Torque Requirements 30 ft-lbs (40.6Nm)

DIMENSIONS

Page 584




TYPICAL SCHEMATIC

ORDERING INFORMATION - - CRACK PRESSURE

CIRCUITS GA OPTIONS 10 10 PSI Buna Standard 00 Viton Standard V0

OUT

B

IN

A

CIRCUIT GA

CVA CVA

CVACVA

RECTIFIER CIRCUIT

USED TO RECTIFY BI-DIRECTIONALFLOW IN CYLINDER LINE FOR USEWITH MONO-DIRECTIONAL COMPONENTS,I.E. FLOW METER, FILTER, OIL COOLER.

Page 585




Pre-Engineered Circuit, Option Model H*

DESCRIPTION Pre-engineered circuit, option model H* OPERATION








DIMENSIONS

Page 586




OPTIONS CHART

ORDERING INFORMATION - - -

CIRCUITS HA VOLTAGE HB 06 6 VDC 12 12 VDC 24 24 VDC OPTIONS 36 36 VDC

Buna Standard 00 48 48 VDC Viton Standard V0 25 25 VAC Buna, Override 0M 11 120 VAC

22 220 VAC “D” COIL TERMINATIONS 44 440 VAC

(All DC Except as Noted) EMMERSION PROOF “D” TYPE

DL Double Lead SS Single Spade IA “I” Coil AMP Superseal - Integral DT Deutsch on Leads DT04-2P DS Double Spade ID “I” Coil Deutsch – Integral DT04-2P ML Metri-Pack on Leads HC DIN 43650 (Hirschman) – (AC & DC) IJ “I” Coil AMP Jr. Timer - Integral PL Packard on Leads CL Conduit Lead – (AC Only) IM “I” Coil Metri-Pack – Integral WL Weatherpack on Leads DI Deutsch – Integral DT04-2P

Approximate Coil Weight: .74 lbs/.33 kg.

Page 587




Pre-Engineered Circuit, Option Model I*

DESCRIPTION Pre-engineered circuit, option model I* OPERATION

See model options for specific operation (back)







DIMENSIONS

Page 588




OPTIONS CHART


CIRCUITS IA OPTIONS 01 .5-1 GPM 02 20-500 PSI IB Buna Standard 00 02 1-2 GPM 15 200-1500 PSI IC Viton Standard V0 VOLTAGE 04 2-4 GPM 30 1500-3000 PSI ID Manual Override 0M 06 6 VDC 08 4-8 GPM 40 2500-4000 PSI IE 12 12 VDC FLOW CONTROL RELIEF VALVE IF 24 24 VDC IG 36 36 VDC IH 48 48 VDC 25 25 VAC VALVE 1




Page 589




Pre-Engineered Circuit, Option Model J*

DESCRIPTION Pre-engineered circuit, option model J* OPERATION

See typical schematic for specific operation.







DIMENSIONS

Page 590




TYPICAL SCHEMATIC

CIRCUIT JA

A B

P T

4W 3P TANDEM CENTER

S4C S4C

ORDERING INFORMATION - - -

CIRCUITS JA VOLTAGE 06 6 VDC 12 12 VDC 24 24 VDC OPTIONS 36 36 VDC

Buna Standard 00 48 48 VDC Viton Standard V0 25 25 VAC Buna, Override 0M 11 120 VAC

22 220 VAC “D” COIL TERMINATIONS 44 440 VAC

(All DC Except as Noted) IMMERSION PROOF “D” TYPE

DL Double Lead SS Single Spade IA “I” Coil AMP Superseal - Integral DT Deutsch on Leads DT04-2P DS Double Spade ID “I” Coil Deutsch – Integral DT04-2P ML Metri-Pack on Leads HC DIN 43650 (Hirschman) – (AC & DC) IJ “I” Coil AMP Jr. Timer - Integral PL Packard on Leads CL Conduit Lead – (AC Only) IM “I” Coil Metri-Pack – Integral WL Weatherpack on Leads DI Deutsch – Integral DT04-2P


Page 591

HYDRAULIC INTEGRATED CIRCUITS Delta Power Company

4484 Boeing Drive - Rockford, IL 61109



Pre-Engineered Circuit, Option Model K*

DESCRIPTION Pre-engineered circuit, option model K* OPERATION









DIMENSIONS

Page 592

HYDRAULIC INTEGRATED CIRCUITS Delta Power Company

4484 Boeing Drive - Rockford, IL 61109



OPTIONS CHART

ORDERING INFORMATION - - - - - VALVE 2

CIRCUITS KA OPTIONS FLOW PRESSURE RANGE KB Buna Standard 00 01 .5-1 GPM 02 20-500 PSI KC Viton Standard V0 VOLTAGE 02 1-2 GPM 15 200-1500 PSI KD Manual Override 0M 06 6 VDC 04 2-4 GPM 30 1500-3000 PSI KE 12 12 VDC 08 4-8 GPM 40 2500-4000 PSI 24 24VDC FLOW CONTROL RELIEF VALVE 36 36 VDC 48 48 VDC 25 25 VAC VALVE 1

11 120 VAC FLOW PRESSURE RANGE “D” COIL TERMINATION 22 220 VAC 01 .5-1 GPM 02 20-500 PSI (All DC Except as Noted) 44 440 VAC 02 1-2 GPM 15 200-1500 PSI 04 2-4 GPM 30 1500-3000 PSI DL Double Lead HC DIN 43650 (Hirschman) – (AC & DC) 08 4-8 GPM 40 2500-4000 PSI DT Deutsch on Leads DT04-2P CL Conduit Lead – (AC Only) FLOW CONTROL RELIEF VALVE ML Metri-Pack on Leads DI Deutsch – Integral DT04-2P PL Packard on Leads IMMERSION PROOF “D” TYPE WL Weatherpack on Leads IA “I” Coil AMP Superseal - Integral FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTOR Y SS Single Spade ID “I” Coil Deutsch – Integral DT04-2P DS Double Spade IJ “I” Coil AMP Jr. Timer - Integral



Page 593




Pre-Engineered Circuit, Option Model L*

DESCRIPTION Pre-engineered circuit, option model L* OPERATION






Operating Fluid Media General Purpose Hydraulic Fluid BODY WEIGHT: 1.80 lbs. [.82 kg.] Cartridge Size Special Series M20X1.5-H6 Thread


DIMENSIONS

Page 594




TYPICAL SCHEMATIC

CIRCUIT LA

V2V1

CB1 CB2

C2C1DUAL COUNTERBALANCE

ORDERING INFORMATION - - - VALVE 2

CIRCUITS LA OPTIONS PRESSURE RANGE Note: Aluminum Bodies are NOT durability rated for Buna Standard 00 15 400-1500 PSI 4000 PSI (276 bar). Consult factory for body options. 40 1500-4000 PSI VALVE 1 PRESSURE RANGE 15 400-1500 PSI 40 1500-4000 PSI FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTORY


Page 595




Pre-Engineered Circuit, Option Model M*

DESCRIPTION Pre-engineered circuit, option model M* OPERATION





Operating Fluid Media General Purpose Hydraulic Fluid BODY WEIGHT: 1.09 lbs. [.49 kg.] Ratio 4 : 1 Cartridge Size M20 X 1.5


DIMENSIONS

Page 596




TYPICAL SCHEMATIC

P.O. CHECK CIRCUIT

CIRCUIT MA

BA

C1 C2

4:1 RATIO

ORDERING INFORMATION - - CRACK PRESSURE CIRCUITS MA OPTIONS 50 50 PSI Buna Standard 00 Viton Standard V0

Page 597




Pre-Engineered Circuit, Option Model N*

DESCRIPTION Pre-engineered circuit, option model N* OPERATION








Coil Torque Nut Requirements 4-6 ft lbs. (5.4-8.1 Nm)

DIMENSIONS

Page 598




OPTIONS CHART

ORDERING INFORMATION - - - - VALVE 1

CIRCUITS NA OPTIONS FLOW PRESSURE NB Buna Standard 00 01 1 GPM 02 20-500 PSI NC Viton Standard V0 VOLTAGE 02 2 GPM 15 250-1500 PSI ND Manual Override 0M 06 6 VDC 03 3 GPM 30 1500-3000 PSI NE 12 12 VDC 04 4 GPM 40 2500-4000 PSI 24 24VDC 05 5 GPM RELIEF VALVE 36 36 VDC 06 6 GPM 48 48 VDC 07 7 GPM 25 25 VAC 08 8 GPM

11 120 VAC 09 9 GPM 22 220 VAC 10 10 GPM 44 440 VAC FLOW CONTROL “D” COIL TERMINATION FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTORY (All DC Except as Noted)

IMMERSION PROOF “D” TYPE DL Double Lead SS Single Spade IA “I” Coil AMP Superseal - Integral DT Deutsch on Leads DT04-2P DS Double Spade ID “I” Coil Deutsch – Integral DT04-2P ML Metri-Pack on Leads HC DIN 43650 (Hirschman) – (AC & DC) IJ “I” Coil AMP Jr. Timer - Integral PL Packard on Leads CL Conduit Lead – (AC Only) IM “I” Coil Metri-Pack – Integral WL Weatherpack on Leads DI Deutsch – Integral DT04-2P


Page 599




Pre-Engineered Circuit, Option Model O*

DESCRIPTION Pre-engineered circuit, option model O* OPERATION





Operating Fluid Media General Purpose Hydraulic Fluid BODY WEIGHT: 1.09 lbs. [.49 kg.] Cartridge Size M20 X 1.5


DIMENSIONS

Page 600




TYPICAL SCHEMATIC

COUNTERBALANCE

CIRCUIT OA

A B

CB1

C1 C2

ORDERING INFORMATION - -

CIRCUITS OA OPTIONS PRESSURE RANGE Buna Standard 00 15 400 – 1500 PSI Viton

Standard V0 40 1500 – 4000 PSI


Page 601




Pre-Engineered Circuit, Option Model P*

DESCRIPTION Pre-engineered circuit, option model P* OPERATION

See options chart for specific operation (back)








DIMENSIONS

Page 602




OPTIONS CHART


CIRCUITS PA OPTIONS 01 .5-1 GPM 07 100-700 PSI PB Buna Standard 00 02 1-2 GPM 30 100-3000 PSI PC Viton Standard V0 VOLTAGE 04 2-4 GPM 40 3000-4000 PSI PD Manual Override 0M 06 6 VDC 08 4-8 GPM RELIEF VALVE 12 12 VDC FLOW CONTROL 24 24 VDC 36 36 VDC 48 48 VDC 25 25 VAC VALVE 1

11 120 VAC FLOW PRESSURE “D” COIL TERMINATION 22 220 VAC 01 .5-1 GPM 07 100-700 PSI (All DC Except as Noted) 44 440 VAC 02 1-2 GPM 30 100-3000 PSI 04 2-4 GPM 40 3000-4000 PSI DL Double Lead HC DIN 43650 (Hirschman) – (AC & DC) 08 4-8 GPM RELIEF VALVE DT Deutsch on Leads DT04-2P CL Conduit Lead – (AC Only) FLOW CONTROL ML Metri-Pack on Leads DI Deutsch – Integral DT04-2P PL Packard on Leads IMMERSION PROOF “D” TYPE FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTORY WL Weatherpack on Leads IA “I” Coil AMP Superseal - Integral SS Single Spade ID “I” Coil Deutsch – Integral DT04-2P DS Double Spade IJ “I” Coil AMP Jr. Timer - Integral



Page 603




Pre-Engineered Circuit, Option Model Q*

DESCRIPTION Pre-engineered circuit, option model Q* OPERATION

See typical schematic for specific operation


Rated Operating Pressure 400-3500 PSI (28-241 bar) Viscosity Range 36 to 3000 SSU (3 to 647 cSt) Filtration 30 micron nominal





DIMENSIONS

Page 604




OPTIONS CHART

ORDERING INFORMATION - - - CIRCUITS QA OPTIONS Buna Standard 00 Viton Standard V0 VOLTAGE Manual Override 0M 06 6 VDC 12 12 VDC 24 24VDC 36 36 VDC 48 48 VDC 25 25 VAC

11 120 VAC 22 220 VAC “D” COIL TERMINATION 44 440 VAC (All DC Except as Noted) IMMERSION PROOF COILS DL Double Lead SS Single Spade IA “I” Coil AMP Superseal - Integral DT Deutsch on Leads DT04-2P DS Double Spade ID “I” Coil Deutsch – Integral DT04-2P ML Metri-Pack on Leads HC DIN 43650 (Hirschman) – (AC & DC) IJ “I” Coil AMP Jr. Timer - Integral PL Packard on Leads CL Conduit Lead – (AC Only) IM “I” Coil Metri-Pack – Integral WL Weatherpack on Leads DI Deutsch – Integral DT04-2P Approximate Coil Weight: .74 lbs/.33 kg.

Page 605




Pre-Engineered Circuit, Option Model R*

DESCRIPTION Pre-engineered circuit, option model R* OPERATION






BODY WEIGHT: .66 lbs. [.30 kg.] Cartridge Torque Requirements 30 ft-lbs (40.6 Nm)

DIMENSIONS

Page 606




TYPICALSCHEMATIC

CIRCUIT RA

P

G

P

T

ORDERING INFORMATION - - CIRCUITS RA OPTIONS Buna Standard 00 Viton

Standard V0

PRESSURE RANGE 40 100 – 4000 PSI


Page 607




Pre-Engineered Circuit, Option Model S*

DESCRIPTION Pre-engineered circuit, option model S* OPERATION


VALVE SPECIFICATIONS Nominal Flow See Option Chart for Flow Range

Rated Operating Pressure See Option Chart for Pressure Range





Coil Torque Nut Requirements 6 ft-lbs. (8.1 Nm)

DIMENSIONS

Page 608




OPTIONS CHART

10 GPM NOMINAL

V2

10 GPM NOMINAL

V1

1

CIRCUIT SC

V1 V2

2C1

2

C2

1

C2

V2

C2

10 GPM NOMINAL

C1

V1

VALVE 1

1

C1

2

MOWER BREAKAWAY

CIRCUIT SA

V1

C1 RVA

2

V2

C2RVA

1

VALVE 2

CROSS OVER RELIEF

V1 V2

1

C1 C2

2

RVA

CIRCUIT SBS2CV11

C12

V2

C2

UNLOADING & RELIEF

PSD

PSD

ORDERING INFORMATION - - - - - VALVE 2 FLOW PRESSURE CIRCUITS SA OPTIONS 01 .5-1 GPM 15 150-1500PSI SB Buna Standard 00 02 1-2 GPM 30 1500-3000 PSI SC Viton Standard V0 VOLTAGE 04 2-4 GPM 40 2500-4000 PSI 06 6 VDC 08 4/8 GPM RELIEF VALVE 12 12 VDC FLOW CONTROL 24 24 VDC 36 36 VDC 48 48 VDC 25 25 VAC VALVE 1 11 120 VAC FLOW PRESSURE “D” COIL TERMINATION 22 220 VAC 01 .5-1 GPM 15 150-1500 PSI (All DC Except as Noted) 44 440 VAC 02 1-2 GPM 30 1500-3000 PSI 04 2-4 GPM 40 2500-4000 PSI DL Double Lead HC DIN 43650 (Hirschman) – (AC & DC) 08 4-8 GPM RELIEF VALVE DT Deutsch on Leads DT04-2P CL Conduit Lead – (AC Only) FLOW CONTROL ML Metri-Pack on Leads DI Deutsch – Integral DT04-2P PL Packard on Leads IMMERSION PROOF “D” TYPE WL Weatherpack on Leads IA “I” Coil AMP Superseal - Integral SS Single Spade ID “I” Coil Deutsch – Integral DT04-2P FOR SPECIAL PRESET VALUES ON VALVES, CONSULT FACTORY DS Double Spade IJ “I” Coil AMP Jr. Timer - Integral IM “I” Coil Metri-Pack – Integral Approximate Coil Weight: .74 lbs (.33 kg.)

Page 609




Pre-Engineered Circuit, Option Model TA

DESCRIPTION 16 size, 1 5/16-12 thread, “Super” series, pilot operated ball check valve. OPERATION The TA allows flow to pass from (V1) to (C1) and (V2) to (C2). The valve blocks flow from (C1) to (V1) and from (C2) to (V2). Blocked flow is released when pilot pressure is applied to port opposite valve (V1) and/or port (V2) accordingly. FEATURES

TYPICAL SCHEMATIC



PERFORMANCE Actual Test Data (Cartridge Only) VALVE SPECIFICATIONS

Nominal Flow 20 GPM (76 LPM) Rated Operating Pressure 3000 PSI (207 bar) Typical Internal Leakage (150 SSU) 0-5 drops min


Weight 4.3 lbs. (2.0 kg) Operating Fluid Media General Purpose Hydraulic Fluid Cartridge Torque Requirements 30 ft-lbs (40.6 Nm)


0

50

100

150

200

250

300

0 2 4 6 8 10 12

Flow (GPM)

Pres

sure

Dro

p (P

SI)

0

5

10

15

20

0 10 20 30 40Flow (LPM)

Pres

sure

Dro

p (B

AR

)

Free Flow 2 to 1 Piloted Open 1 to 2

Page 610




DIMENSIONS

ORDERING INFORMATION -

CIRCUITS TA OPTIONS Buna Standard 00 Viton Standard V0

Page 611

Page 612

Documents

HYDRAULIC INTEGRATED CIRCUITS Delta Power · PDF fileHYDRAULIC INTEGRATED CIRCUITS Delta Power Company ... HYDRAULIC INTEGRATED CIRCUITS Delta Power Company ... Rectifier Circuit