of 17/17
as of 3 November 2017 Page 1 of 17 I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY INDONESIA I. RATIONALE FOR REGULATION COUNTRY RATIONALE FOR REGULATION Indonesia Consumer Protection II. REGULATION BODY COUNTRY REGULATORY BODY Indonesia Ministry of Industry Ministry of Energy and Mineral Resources Ministry of Trade

I. RATIONALE FOR REGULATION COUNTRY RATIONALE FOR REGULATIONasean.org/storage/2012/10/Reg-regime-of-Indonesia_aso… ·  · 2017-11-03I. RATIONALE FOR REGULATION COUNTRY RATIONALE

  • View
    217

  • Download
    0

Embed Size (px)

Text of I. RATIONALE FOR REGULATION COUNTRY RATIONALE FOR...

  • as of 3 November 2017

    Page 1 of 17

    I. COUNTRIES WITH MANDATORY STANDARDS FOR GOVERNMENT PROCUREMENT ONLY

    INDONESIA

    I. RATIONALE FOR REGULATION

    COUNTRY RATIONALE FOR REGULATION

    Indonesia Consumer Protection

    II. REGULATION BODY

    COUNTRY REGULATORY BODY

    Indonesia

    Ministry of Industry Ministry of Energy and Mineral Resources Ministry of Trade

  • as of 3 November 2017

    Page 2 of 17

    III. LEGISLATIVE FRAMEWORK

    COUNTRY LEGISLATIVE FRAMEWORK

    Indonesia 1. Act No. 8 / 1999 concerning Consumer Protection

    2. Act No. 3 / 2014 concerning Industry

    3. Act No. 7 / 2014 concerning Trade

    4. Act No. 20 /2014 concerning Standardization and Conformity Assessment

    5. Government Regulation No. 102/2000 concerning National Standardization

    6. Decree of the Minister of Industry No. 86/M-IND/PER/9/2009 concerning the Implementation of

    SNI in Industrial Sector

    7. Decree of the Minister of Industry No. 51/M-IND/PER/3/2012 concerning The Procedures for

    Recognition of Certification Product of Electrical and Electronic Equipment Issued by

    Conformity Assessment Bodies Listed in ASEAN

    8. Decree of the Minister of Energy and Mineral Resorces No. 01/2016 concerning The

    Procedures for Recognition of Product Certification and Product Test Report of Electrical and

    Electronic Equipment Issued by Conformity Assessment Bodies Listed in ASEAN

    9. Decree of the Minister of Trade No. 24/M-DAG/PER/4/2016 concerning Standardization on

    Trade Sector

  • as of 3 November 2017

    Page 3 of 17

    IV. MANDATORY STANDARDS

    Product type or grouping

    STANDARDS

    State reason if MOD

    Indicate

    whether

    requires:

    Safety (S),

    Environment

    (E), EMC,

    or combinatio

    n

    HS Code Type of

    Certification Domestic Standards Please tick

    box if mandatory

    Relevant International Standards

    Extent of Alignment

    Incandescent lamps

    SNI 04-3560-1994 V IEC 60064 Ed.6 (1993-12)

    IDT S 5

    Self-ballast lamp for general lighting service

    SNI 04-6504-2001 V IEC 60968 Ed.1.0 (1988-11)

    IDT S 8539.31.30 5

    Plugs and socket-outlets for household and similar purposes. Part 1 : General requirement

    SNI 04-3892.1-2006 V IEC 60884-1 (2002-06)

    IDT S 8536.69.92 8536.69.99

    5

    Switches for household installations and similar fixed electric. Part 1: General requirements

    SNI 04-6203.1-2006 V IEC 60669-1 (2000)

    IDT S 8536.50.61 8536.50.69 8536.50.99

    5

    Circuit breakers for over current protection for household and similar installation. Part 1 : Circuit breaker for a.c operated

    SNI 04-6507.1-2002

    SNI 04-6507.1-2002/Amd1. 2006

    V IEC 60898-1 (2003)

    IDT S 8536.20.91 8536.20.99

    5

    Electrical appliances for household usages and other similar types of safety products; Part 2-80. Special requirements for electric fan

    SNI 04-6292.2.80-2006

    V IEC 60335-2-80(2004-03)

    IDT S 8414.51.10 8414.51.91 8414.51.99

    5

    Lamp controlgears - Part 1: General and safety requirements

    SNI 04-6959.1-2003

    V IEC 61347-1 (2000-10) IDT

    S 8504.10.00 5

    Lamp controlgears - Part 2-3: Particular requirements for a.c. supplied electronic ballasts for fluorescent lamps

    SNI 04-6959.2.3-2003

    V IEC 61347-2-3 (2000-10) IDT

    S 8504.10.00 5

  • as of 3 November 2017

    Page 4 of 17

    Product type or grouping

    STANDARDS

    State reason if MOD

    Indicate

    whether

    requires:

    Safety (S),

    Environment

    (E), EMC, or

    combination

    HS Code Type of

    Certification Domestic Standards Please tick

    box if mandatory

    Relevant International Standards

    Extent of Alignment

    Residual current operated circuit - breakers without integral overcurrent protection for household and similar uses (RCCB) - Part 1: General rules

    SNI 04-6956.1-2003 V IEC 61008-1 (1996-12) IDT S 8536.20.91 8536.20.99

    5

    Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part 2-1: Applicability of the general rules to RCCBs functionally independent of line voltage

    SNI 04-6956.2.1-2005

    V IEC 61008-2-1 (1990-12) IDT S 8536.20.91 8536.20.99

    5

    Luminaires - Part 1: General requirements and tests

    SNI 4 -6973.1-2005 V IEC 60598-1 (2003)

    IDT

    S 9405.10.30 9405.10.40 9405.10.90

    5

    Luminaires - Part 2-1: Particular requirements - Fixed general purpose luminaires

    SNI 4 -6973.2.1-2005

    V IEC 60598-2-1 (1979) IDT

    S 9405.10.30 9405.10.40 9405.10.90

    5

    Luminaires - Part 2-2: Particular requirements - Recessed luminaires

    SNI 4 -6973.2.2-2005

    V IEC 60598-2-2 (1997)

    IDT

    S 9405.10.30 9405.10.40 9405.10.90

    5

    Luminaires - Part 2-3: Particular requirements - Luminaires for road and street lighting

    SNI 4 -6973.2.3-2005

    V IEC 60598-2-3 (2002) IDT

    S 9405.40.50 5

    Luminaires - Part 2-5: Particular requirements Floodlights

    SNI 4 -6973.2.5-2005

    V IEC 60598-2-5 (1998): IDT

    S 9405.10.30 9405.40.20 9405.40.40

    5

    Primary Battery - part 1: General SNI 04-2051.1-2004 V

    IEC 60086-1 (2000)

    IDT

    S 8506.10.10 8506.10.90 8506.50.00 8506.80.10 8506.80.20

    5

  • as of 3 November 2017

    Page 5 of 17

    Product type or grouping

    STANDARDS

    State reason if MOD

    Indicate

    whether

    requires:

    Safety (S),

    Environment

    (E), EMC, or

    combination

    HS Code Type of

    Certification Domestic Standards Please tick

    box if mandatory

    Relevant International Standards

    Extent of Alignment

    Primary Battery - part 2: Electrical and Physical Requirement

    SNI 04-2051.2-2004 V IEC 60086-2 (2000)

    IDT

    S 8506.10.10 8506.10.90 8506.50.00 8506.80.10 8506.80.20

    5

    PVC insulated cables with a rated voltage up to 450/750 V - Part 3: Non-sheated cables for fixed wiring

    SNI 04-6629.3-2006 V IEC 60227-3(1997-11) IDT

    S 8544.11.20 8544.11.30 8544.11.40 8544.11.90 8544.49.22

    5

    PVC insulated cables with a rated voltage up to 450/750 V - Part 4: Sheated cables for fixed wiring

    SNI 04-6629.4-2006 V IEC 60227-4(1997-12) IDT

    S 8544.11.20 8544.11.30 8544.11.40 8544.11.90 8544.42.94 8544.42.95 8544.42.96 8544.42.97 8544.49.22

    5

    PVC insulated cables with a rated voltage up to 450/750 V - Part 5: Flexible cables

    SNI 04-6629.5-2006 V IEC 60227-5(2003-07) IDT

    S 8544.11.20 8544.11.30 8544.11.40 8544.11.90 8544.42.94 8544.42.95 8544.42.96 8544.42.97 8544.49.22 8544.49.23 8544.49.41

    5

  • as of 3 November 2017

    Page 6 of 17

    Product type or grouping

    STANDARDS

    State reason if MOD

    Indicate

    whether

    requires:

    Safety (S),

    Environment

    (E), EMC, or

    combination

    HS Code Type of

    Certification Domestic Standards Please tick

    box if mandatory

    Relevant International Standards

    Extent of Alignment

    Safety of household and similar electrical appliances Part 2-41 : Particular requirements for pumps

    SNI 04-6292.2.41-2003

    V IEC 60335-2-41 (2002-10)

    IDT

    S 8413.70.42 8413.70.91 8413.81.13

    5

    Household and similar electrical appliances Safety Part 2-3: Particular requirements for electric irons

    SNI 04-6292.2.3-2003

    V IEC 60335-2-3 (2002-03)

    IDT

    S 8516.40.90 5

    Audio, video and similar electronic apparatus Safety requirements

    SNI 04-6253-2003 V IEC 60065 (200112) MOD 4.1.3 Unless otherwise specified, the tests are carried out under normal operating conditions at: - anambient temperature between 20 oC and 35 oC - a relative humidity of 70 % 15% maximum

    S 8528.72.91 5

    Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers

    SNI IEC 60335-2-40:2009

    V IEC 60335-2-40 Ed 4.2 (2005-07)

    IDT

    S 8415.10.10 5

  • as of 3 November 2017

    Page 7 of 17

    Product type or grouping

    STANDARDS

    State reason if MOD

    Indicate

    whether

    requires:

    Safety (S),

    Environment

    (E), EMC, or

    combination

    HS Code Type of

    Certification Domestic Standards Please tick

    box if mandatory

    Relevant International Standards

    Extent of Alignment

    Household and similar electrical appliances - Safety - Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers

    SNI IEC 60335-2-24:2009

    V IEC 60335-2-24 Ed 6.1 (2005-04)

    IDT

    S 8418.10.11 8418.10.19 8418.21.10 8418.21.90 8418.29.00 8418.30.10 8418.30.90 8418.40.10 8418.40.90

    5

    Household and similar electrical appliances - Safety - Part 2-7: Particular requirements for washing machines

    SNI IEC 60335-2-7:2009

    V IEC 60335-2-7 (2004-11)

    IDT

    S 8450.11.10 8450.11.90 8450.12.10 8450.12.90 8450.19.11 8450.19.19

    5

  • as of 3 November 2017

    Page 8 of 17

    V. MODE OF REGULATION AND TYPES OF CONFORMITY ASSESSMENT REGIMES

    COUNTRY TYPES OF CON-FORMITY ASSESS-

    MENT REGIMES

    MODE OF REGULATION

    Indonesia Technical Regulation based on SNI

    Technical regulation on EEE by adopting partially or fully technical specification and/or parameter of SNI is stipulated by Ministerial Decree taking into account safety, security, health, environment, moral hazard, and economical aspects, that are equally imposed to both domestic and imported products which are traded in Indonesian teritory.

    Manufacturers of EEE which are technically regulated based on SNI shall fulfill the SNI requirements and shall affix the SNI mark on the products, packages and/or label of their products

    Product Registration to get NPB (for imported products) or NRP (for domestic products)

    Pre-market surveillance over traded goods produced domestically, shall be done through Product Registration Number (Nomor Registrasi Produk - NRP)

    Pre-market surveillance over imported of EEE shall be done through Goods Registration Number (Nomor Pendaftaran Barang NPB),

    NRP and NPB shall be issued by the Director of Standardization and Quality Control, Ministry of Trade

    The validity of NRP and NPB are in accordance with the validity period of SPPT SNI.

    NRP or NPB shall affix underneath SNI Mark and/or other recognized conformity mark, on to their products or packages.

  • as of 3 November 2017

    Page 9 of 17

    COUNTRY TYPES OF CON-FORMITY ASSESS-

    MENT REGIMES

    MODE OF REGULATION

    Registration of CAB CAB issuing an SNI Mark Product Certification can be a domestic or foreign product certification body supported by accredited testing laboratories and/or inspection institutions.

    Domestic CAB shall be accredited by KAN according to its scopes, CAB shall be

    registered to the Directorate of Standardisation and Quality Control, Ministry of Trade.

    All CAB which have the scope of mandatory SNIs requirements shall be accredited by National Accreditation Body of Indonesia (KAN) and assigned by Minister of Industry

  • as of 3 November 2017

    Page 10 of 17

    VI. FLOWCHART OF INDONESIAS REGIME

    PROCEDURES FOR RECOGNITION OF CERTIFICATES OF EEE FROM CONFORMITY ASSESSMENT BODIES IN ASEAN

    COUNTRIES

    AMS Indonesia

    Listed Product Certification Body for EEE

    Listed Testing Lab. for EEE

    Product Certification Body

    SPPT SNI according to certification type ISO/IEC 17067

    Product EEE ASEAN

    Legend: 1. Using Certificate of Conformity issued by AMS Listed Product Certification Body 2. Using Testing report issued by AMS Listed Testing Lab.

    Listed Testing lab have to be accredited for full parameter of the standards 3. Direct to Indonesia Registered Product Certification Body

    3

    1

    2

  • as of 3 November 2017

    Page 11 of 17

    EEE products from ASEAN countries could enter Indonesia through three mechanisms:

    1. Using Certificate of Conformity (CoC) from Product CB outside Indonesia

    1.1 Manufacturer certify their products in CB from outside Indonesia (Listed in ASEAN).

    1.2 Importer submits an application to Registered CB in Indonesia to issue SPPT-SNI, by attaching required documents.

    1.3 CB in Indonesia verifies the application and the documents.

    1.4 In the case of questionable data/information in CoC and/or test report, CB in Indonesia may re-test the product.

    1.5 In the case of different edition of referenced standard, modification, or others, CB in Indonesia may take test of untested

    parameters.

    1.6 Based on verification result, CB in Indonesia may approve or reject the application.

    1.7 CB in Indonesia will conduct market surveillance

    1.8 CB in Indonesia will evaluate factory surveillance report conducted by foreign CB which issued CoC.

    2. Using test report from testing laboratory in home country

    2.1 Manufacturer test their product in Testing laboratory in their home country (Listed in ASEAN)

    2.2 Importer submits an application to Registered CB in Indonesia to issue SPPT-SNI, by attaching required documents.

    2.3 CB in Indonesia verifies the application and the documents.

    2.4 In the case of questionable data/information in test report, CB in Indonesia may re-test the product.

    2.5 In the case of different edition of referenced standard, modification, or others, CB in Indonesia may take test of untested

    parameters.

    2.6 Based on verification result, CB in Indonesia may approve or reject the application.

    2.7 In the case of the application is approved, CB in Indonesia will continue the certification process (including factory audit) and

    issues SPPT-SNI or reject the application.

    2.8 CB in Indonesia will conduct market surveillance.

  • as of 3 November 2017

    Page 12 of 17

    3. Using Indonesia Registered Product CB

    Manufacturer certify their products using Indonesia Registered Product CB.

    VII. MAINS VOLTAGE, FREQUENCY AND MAINS PLUG CONFIGURATION

    Country Mains

    Voltage and Tolerance

    Mains Frequency and Tolerance

    Applicable Legislation

    Mains Plug Configuration

    Domestic Standard

    Please tick box if mandatory

    Relevant International Standard

    Extent of Alignment -

    Diagram of Mains Plug Configuration-

    Indonesia 230 5% 50 5% SNI 04-3892.1-2006

    Plugs and socket-outlets for household and similar purposes. Part 1 : General requirement

    V

    IEC 60884-1

    Ed.3.0(2002,am.1(2006)

    IEC 60884-2-1 Ed.1.0(1987)

    IEC 60884-2-3 Ed.1.0(1989) (0nly for the

    safety)

    SNI 04-3892.2.3-

    2000:Plugs and Sockets-Outlets for household and similar purposes;Part 2.3:Particular Requirement for switched socket outlets without interlock for fixed installation.

  • as of 3 November 2017

    Page 13 of 17

    Country Mains Voltage and Tolerance

    Mains Frequency and Tolerance

    Applicable Legislation

    Mains Plug Configuration

    Domestic Standard

    Please tick box if mandatory

    Relevant International Standard

    Extent of Alignment -

    Diagram of Mains Plug Configuration-

    SNI 04-6202-

    2000: Plugs and Sockets-Outlets and couplers for industrial purposes;Part 3: Particular Requirement for plugs, socket outlets, connectors and appliance inlets for use in explosive gas atmospheres.

    SNI 04-0225-

    2000/Amd1-2006 on Amendment 1 of Indonesian National Standard for General Requirements on Electrical Installation

    V IEC 60364 (series)

  • as of 3 November 2017

    Page 14 of 17

    VIII. MARKING/LOGO :

    Affixing SNI and NRP

    Note:

    101 : Product Certification Body certifying the products 010 : Factory Location 000001 : Registration Number in Directorate of Standardization and Quality Control

  • as of 3 November 2017

    Page 15 of 17

    Affixing SNI and NPB

    Note:

    101 : Product Certification Body certifying the products 156 : Country of Origin 000001 : Registration Number in Directorate of Standardization and Quality Control

  • as of 3 November 2017

    Page 16 of 17

    IX. OTHER INFORMATION

    No Product Additional Requirement Link for Technical Regulation

    1.

    Air Conditioner (AC)

    - Minimum class I Insulation - Supply cable must SNI certified

    http://pustan.kemenperin.go.id/public/default/file_juknis/No_30_IUBTT_2013%20AC%20kulkas%20mesin%20cuci.pdf

    2. Refrigerator

    - Minimum class I Insulation - Supply cable must SNI certified - Plug must SNI certified - Gross capacity is calculated

    based on SNI ISO 15502:2008

    3. Washing Machine

    - Minimum class I Insulation - Supply cable must SNI certified - Plug must SNI certified - Loading capacity is calculated

    based on IEC 60456

    4. Water Pump

    - Minimum class I Insulation - Supply cable must SNI certified - Plug must SNI certified

    http://pustan.kemenperin.go.id/public/default/file_juknis/Juknis_SNI_04-6292.2.3-2003%202.pdf

    5. Electric iron

    - Minimum class I Insulation - Supply cable must SNI certified - Plug must must SNI certified

    6. CRT Television - Minimum class II Insulation - Supply cable must SNI certified - Plug must SNI certified

    http://pustan.kemenperin.go.id/public/default/file_juknis/No_30_IUBTT_2013%20AC%20kulkas%20mesin%20cuci.pdfhttp://pustan.kemenperin.go.id/public/default/file_juknis/No_30_IUBTT_2013%20AC%20kulkas%20mesin%20cuci.pdfhttp://pustan.kemenperin.go.id/public/default/file_juknis/Juknis_SNI_04-6292.2.3-2003%202.pdfhttp://pustan.kemenperin.go.id/public/default/file_juknis/Juknis_SNI_04-6292.2.3-2003%202.pdf

  • as of 3 November 2017

    Page 17 of 17

    X. CONTACT PERSON

    Country JSC EEE

    Indonesia Representative Officer Chandrini M. Dewi Director of Standardization and Quality Control Directorate General of Consumer Protection and Trade Compliance Ministry of Trade Jl. Raya Bogor KM 26 Ciracas - Jakarta Timur Telp : (021) 8710321/3Fax : 62-21-3863928 E-mail : [email protected], [email protected] Contact Person Konny Sagala, S.Si Head of Center for Cooperation on Standardization - BSN BPPT I Building Jl. M.H. Thamrin No. 8, Kebon Sirih Jakarta Pusat 10340 Indonesia Phone : 62-21-3927422 Fax : 62-21-3927527 E-mail : [email protected], [email protected] Designating Body Wahyu Purbowasito Setyo Waskito Head of Center for Standard Application System - BSN BPPT I Building Jl. M.H. Thamrin No. 8, Kebon Sirih Jakarta Pusat 10340 Indonesia Phone : 62-21-3927422 Fax : 62-21-3927527 E-mail : [email protected]

    mailto:[email protected]:[email protected]:[email protected]:[email protected]