2
Example: Twin installation with (left) and without (right) accessories connected on the AUX bus Installation Procedure: EVC-E2 Volvo Penta IPS Twin Installation Procedure: EVC-E2 Volvo Penta IPS Twin Document number: 47704056 Release date: 05-2013 Buzzer Connection for safety lanyard Rudder angle sender (not used) Fresh water and fuel level senders SUS IMPORTANT! Never cut or modify the Volvo Penta EVC harnesses. For extra power supply, use the Volvo Penta relay for external accessories. Use cable ties. Typical installation / Main station IPS 350/400/450/500/600, IPS 800/950, IPS 1050/1200 1 2 7 4 5 Multisensor SUS CPM ACP 7” display Autopilot 4” display To NMEA2000 backbone Compass (CCU) Joystick Steering wheel Levers Lever connections 5 9 10 12 Multilink hub Termination plug 12 10 Termination plug 1 20 7 7 7 25 7 AUX bus termination D11 D11 Flybridge Joystick Steering wheel Multilink hub Buzzer Multifunction panel (Start/Stop panel) Dynamic Positioning System interface Dynamic Positioning System antenna 7” display Levers Lever connections 10 11 11 18 9 Autopilot 4” display To NMEA2000 backbone 10 10 20 20 Display options Twin Female terminator Male terminator Chartplotter EVC Autopilot Compass (CCU) EVC Autopilot Battery 12 VDC T-connector Backbone ex- tension cable Fuse Power cable 23 20 20 20 20 Use AUX relay 24 20 22 24 e-Key panel Engine connections IPS 350/400/450/500/600 IPS 1050/1200 AUX BUS AUX BUS AUX BUS AUX BUS AUX BUS AUX BUS SENDERS DATALINK DATALINK DATALINK SENDERS SENDERS A C ENGINE CONN. DIAGNOS Connection locations B A C Docking station Joystick Stand- alone HCU Multifunction panel (Docking station panel) Stand-alone HCU connections Buzzer 11 11 10 Interceptor Control Unit (ICU) Color coded cables Interceptor Servo unit Interceptor Servo unit Connecting multiple Multilink hubs B IPS 800/950 31 31 To next station To next station IMPORTANT! This end of Y-connector must be connected directly, without extension, to levers/HCU. Helm station Helm station 8 8 7 8 8 Engine Engine 8 11 11 11 7 11 Multiple helm stations Y-connector Buzzer Connection for safety lanyard Analog Key Analog key interface (optional) 7” display NMEA2000 backbone 7 7 MAX MIN MIN 4” display 2,5” display MAX MIN MAX Correct! Termination in the beginning and at the end of the AUX bus Termination plug 5 7 7 7 7 2 7 7 10 33 There is no need of termination plugs if nothing is connected on the AUX bus. IMPORTANT! Maximum cable length between Multil- ink hub and unit (display etc.) is 3 m (10 ft). Maximum total cable length on Multilink is 20 m (66 ft). 7 7

Installation Procedure: EVC-E2 Volvo Penta IPS Twin ... · Installation Procedure: Installation Procedure: EVC-E2 Volvo Penta IPS Twin EVC-E2 Volvo Penta IPS Twin ... for 12 V systems

  • Upload
    vokhanh

  • View
    573

  • Download
    16

Embed Size (px)

Citation preview

Page 1: Installation Procedure: EVC-E2 Volvo Penta IPS Twin ... · Installation Procedure: Installation Procedure: EVC-E2 Volvo Penta IPS Twin EVC-E2 Volvo Penta IPS Twin ... for 12 V systems

Example: Twin installation with (left) and without (right) accessories connected on the AUX bus

Installation Procedure: EVC-E2 Volvo Penta IPS TwinInstallation Procedure: EVC-E2 Volvo Penta IPS Twin

Document number: 47704056

Release date: 05-2013

Buzzer

Connection for safety lanyard

Rudder angle sender (not used)

Fresh water and fuel level senders

SUS

IMPORTANT! Never cut or modify the Volvo Penta EVC harnesses. For extra power supply, use the Volvo Penta relay for external accessories. Use cable ties.

Typical installation / Main station

IPS 350/400/450/500/600, IPS 800/950, IPS 1050/1200

1

2

7

4

5

Multisensor

SUS

CPM

ACP

7” display

Autopilot 4” display

To NMEA2000 backbone

Compass (CCU)

Joystick

Steering wheelLevers

Lever connections

5

910

12

Multilink hub

Termination plug

12

10

Termination plug

1

20

7

7

7

25

7

AUX bus termination

D11

D11

Flybridge

Joystick

Steering wheel Multilink hub

Buzzer

Multifunction panel(Start/Stop panel)

Dynamic Positioning System interface

Dynamic Positioning System antenna

7” display

Levers

Lever connections

10

11 11

18

9

Autopilot 4” display

To NMEA2000 backbone

10

10

20

20

Display options Twin

Female terminator

Male terminator

ChartplotterEVC AutopilotCompass (CCU)EVC Autopilot

Battery 12 VDC

T-connectorBackbone ex-tension cable

Fuse Power cable

23 20

20 2020Use AUX relay

24 20 22 24

e-Key panelEngine connections

IPS 350/400/450/500/600

IPS 1050/1200

AU

X BU

SA

UX B

US

AU

X BU

S

AUX BUS

AUX BUS

AU

X BU

S

SEN

DER

S

DATA

LINK

DATALINK

DATA

LINK

SENDERS

SEN

DER

S

A

C

ENGINE CONN.

DIAGNOS

Connection locations

BA C

Docking station

Joystick

Stand-alone HCU

Multifunction panel(Docking station panel)

Stand-alone HCU connections

Buzzer

11 11

10

Interceptor Control Unit (ICU)

Color coded cables Interceptor Servo unitInterceptor Servo unit

Connecting multiple Multilink hubs

B

IPS 800/950

3131

To next station To next station

IMPORTANT! This end of Y-connector must be connected directly, without extension, to levers/HCU.

Helm station

Helm station

8

8

7

8

8

Engine Engine

8

11

11 11

7

11

Multiple helm stationsY-connector

Buzzer

Connection for safety lanyard

Analog Key

Analog key interface (optional)

7” display

NMEA2000 backbone

77

MAXMIN

MIN

4” display

2,5” display

MAX

MIN

MAX

Correct!Termination in the beginning and at the end of the AUX bus

Termination plug

5

7 7 7 7

2

7

7

10

33

There is no need of termination plugs if nothing is connected on the AUX bus.

IMPORTANT! Maximum cable length between Multil-ink hub and unit (display etc.) is 3 m (10 ft).Maximum total cable length on Multilink is 20 m (66 ft).

7

7

Page 2: Installation Procedure: EVC-E2 Volvo Penta IPS Twin ... · Installation Procedure: Installation Procedure: EVC-E2 Volvo Penta IPS Twin EVC-E2 Volvo Penta IPS Twin ... for 12 V systems

e-KeyPart no. 21758351

Compass (CCU)Part no. 21812209

Steering wheel non tilt adjuster

Steering

JoystickIncl. cables 1.5 m (5 ft.)

Steering wheel tilt adjuster Steering wheel hubIncl. cables 2.5 m (8 ft.)

Interceptor Control Module (ICM)Manual: 21888398 Auto/Manual: 21875631

47

70

40

56

05

-20

13

Components and CablesControls

Components

Stand-alone HCU

Part no. 21856286

LeversBuilt-in HCUsPart no. 21856280

Levers“Palm Beach” In combination with A-CANPart no. 3888616

e-Key panelIgnition, start/stop and locking/unlocking the boat system.Kit no. 21836809

Multilink hub6 cable socketsKit no. 21469055

Autopilot interface NMEA 0183 interface NMEA 2000 interface

Dynamic Positioning System interface

7” display power supply for 12 V systems

MultisensorTransom mountedKit no. 3587055

A-CANAnalog lever interfaceKit no. 21460908

MultisensorHull mounted

SenderFuel level sender 3–180 ohm

SenderWater level sender 3–180 ohm

Clear Wake Exhaust System Only for IPS800-1200Kit no. 21499486

Dynamic Positioning System antennaKit no. 22050476

ACP KitTransom unit Included in ACP-kit Part no. 22037078

ACP KitCPM unit Included in ACP-kit, Active Corrosion Protection for fiber-glass hulls.Part no. 40005219

19. Display cable, 5/6-pinFeet Meter Part no.5 1.5 21640400 Incl. in display kit

20. NMEA 2000 Extension cableFeet Meter Part no.1 0.3 21812185 6.6 2 21812194** 13 4 21867150 19 6 21867151 33 10 21867152

24. NMEA2000 Termination plugs Type Part no.Male 21812196** Female 21812203**

23. NMEA2000 Powercable Feet Meter Part no.6.6 2 21812205**

22. NMEA2000 T-connectorPart no. 21812195**

Cables

7. Standard EVC bus cable, 6-pin* Feet Meter Part no.5 1.5 21865234 16 5.0 874789 23 7.0 889550 30 9.0 889551 36 11.0 889552 42 13.0 888013*) One cable per engine has to be ordered.

8. Y-connector, 6-pinFeet Meter Part no.1.6 0.5 3588972

10. Multilink cable, 6-pinFeet Meter Part no.5 1.5 3886666

11. Extension cable, 6-pinFeet Meter Part no.5 1.5 3889410 10 3.0 3842733 16 5.0 3842734 23 7.0 3842735 30 9.0 3842736 36 11.0 3842737 66 20.0 21172469 131 40.0 21172470

16. Extension cable, 3-pin EasyLinkFeet Meter Part no.3 1.0 874759 10 3.0 3807043

12. Sender cable, 6-pinFeet Meter Part no.16 5.3 3807229

17. Steering adapter, 12/6-pinFeet Meter Part no.0.6 0.2 21421945

15. Extension cable, 6-pin Joystick/Steering wheel hubFeet Meter Part no.5 1.5 21480272

13. Aux. relay cable, 6-pinFeet Meter Part no. 3.3 1.0 21427463Kit with cable & relay 12V: 21475508 24V: 21475509

6. Y-split steering, 6-pinFeet Meter Part no.1.3 0.4 21421941

9. 7” display cable, 6-pinFeet Meter Part no.5.5 1.7 21514712**) Incl. in display kit

14. Extension cable, 6-pin Feet Meter Part no.23 7.0 21166002 30 9.0 21166003 43 13 .0 21166004

18. Y-split multilink, 6-pinFeet Meter Part no.1.6 0.5 3588206

1 b. Wiring harness

IPS 800-950Feet Meter Part no.4.3 1.3 21851490 5.6 1.7 21851491 7.2 2.2 21851492 8.5 2.6 21851493 10.2 3.1 21851494 11.5 3.5 21851495 18 5.5 21851496

1c. Wiring harness

IPS 1050-1200Feet Meter Part no.4.3 1.3 21759842 5.6 1.7 21755840 7.2 2.2 21758217 8.5 2.6 21758219 10.2 3.1 21758220 11.5 3.5 21758221 18 5.5 21858754

2. Multisensor Y-split*Feet Meter Part no.1.9 0.6 21825662*) Wiring harness AUX-bus.

4. CPM Y-split*Feet Meter Part no.1.9 0.6 21825665*) Wiring harness AUX-bus.

5. Termination plugPart no.21825714

2.5” displayNot in combination with 4” or 7” display.Kit no. 21846916

7” display Color displayAutopilot 4” displayColor displayPart no. 21812273

4” display Color display Not in combination with 2.5” or 7” display.Kit no. 22080265

Not in combination with 2.5” or 4” display.Kit no. 22080260

1 a. Wiring harness

IPS 350-600Feet Meter Part no.1.9 0.6 21865860 6.2 1.9 21865861e-Key (standard)

Locking/unlocking the boat system

e-Key System

25. e-Key harness with Safety lanyard Feet Meter Type Part no.5 1.5 Single panel 21693202 5 1.5 Twin panel 21693206

26. e-Key harness without Safety lanyardFeet Meter Type Part no.5 1.5 Single panel 21693204 5 1.5 Twin panel 21693208

Multifunction panelFunction configured at startup.Kit no. 21846926

Kit no. 3587054Part no. 21231837 Included in Dynamic Positioning System antenna kit.

Part no. 21379779

Part no.

Part no. 3809098Part no. 21575479

Kit no. 21230216

Part no. 21469560Part no. 21581323Part no. 21846873Kit no. 21836809

**) Incl. in Autopilot kit:

31. Interceptor servo cableFeet Meter Part no.13 4 21875632 Incl. in Interceptor kit:

Interceptor system Interceptor and servo unit

Kit IS 600 : Part no. 21875622 Kit IS 750 : Part no. 21875623 Kit IS 900 : Part no. 21875624 Kit IS 1050 : Part no. 21875625

32. e-Key extension cable, 12-pinFeet Meter Part no.4.7 1.44 22067251

0183: 38075872000: 3889758

33. Stbd. AKI, 4/8-pin Feet Meter Part no.0.6 0,2 21421946

LeversBuilt-in HCUs with ISPart no. 21897586