114
iTools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Embed Size (px)

Citation preview

Page 1: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

iTools Features & Benefits

CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Page 2: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

TOPICS:

This presentation has over 100 slides. Advance to topic of interest.

1: iTools basic concepts

2: Starting iTools

3: Finding Modules on the Network

4: Parameter View

5: Soft Wiring

6: Toolkit Blocks (Maths and Logic Blocks)

7: User Page Views (2704)

8: Watch Recipe (custom views)

9: Views: Programmer (SETPOINT PROGRAMS)

10: OPC SCOPE (Datalogging)

11: Saving module configuration setting

12: Simulation & Off line clone creation

13: OPC Server (iTools OPEN Version)

14: Application: Remote Sites

Page 3: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

iTools software runs on any PC allowing configuration, monitoring and control of

equipment on a serial network.

ModBus

iTools running

on PC

iTools Basics.

Modules on ModBus network

Page 4: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

iTools software blocks running on PC

iTools- Configuration- Cloning

SCADA- Wonderware- CiTechOPC

OPC

OPC

ModBus

DDE

OPC Scope- Trend plots- Watch screen- Datalogging- User screens

Excel- Analysis- Historical trend plots

OPC -ModBus server

Serial Input to PC

iTools Basics.

Page 5: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

iTools Advanced Features

• OPC client/server architecture– SCADA integration, e.g. Wonderware & CiTech,

with no additional drivers• OPC = OLE for Process Control

{Faster than DDE}• OLE = Object Linking and Embedding

– Support for DDE included

• ActiveX components– User can build own views using Visual Basic etc.

• OPC client/server architecture– SCADA integration, e.g. Wonderware & CiTech,

with no additional drivers• OPC = OLE for Process Control

{Faster than DDE}• OLE = Object Linking and Embedding

– Support for DDE included

• ActiveX components– User can build own views using Visual Basic etc.

Page 6: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Operating Systems

• Windows 95• Windows 98• Windows Me• Windows NT 4.0 (SP4 or later)

– installation requires Administrator privileges

• Windows 2000– installation requires Administrator privileges

Page 7: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

• minimum 40MB hard disk space

System Requirements

OS MINIMUM RECOMMENDED

Windows 95 Pentium 16624MB 48MB

Windows 98Windows NT 4.0

Pentium 20032MB 64MB

Windows MeWindows 2000

Pentium II 26664MB 128MB

Page 8: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

iTools Editions• DEMO - no Product Key required

– some functions disabled– communications limited to 30 minutes

• STANDARD– all features available except third party access to

the OPC ModBus server

• OPEN– all features available with third party access to the

OPC ModBus server. Use this edition if Wonderware or some other SCADA is a client

Page 9: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

• ModBus OPC Server– communications driver

• iTools Remote– launches iTools with option to connect to a ModBus

OPC Server running on a remote computer

• IDM Manager– may be used to install support for additional device

types– IDM = Instrument Descriptor Module

• provides complete characterisation of a device type/version

• iTools Installation Diagnostics– helpdesk aid

iTools applications - advanced

Page 10: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

iTools communications

• iTools communications driver is a ModBus OPC server

• Supported communications protocols:– Serial ModBus (RS232 or RS485)– Eurotherm factory communications

• based closely on serial ModBus

– ModBus TCP• for use over Ethernet TCP/IP• typically requires a ModBus TCP to serial ModBus

gateway, e.g. a Lantronix CoBox

• No support for communications over ProfiBus

Page 11: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Start the iTools program from the default install location.

Page 12: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

SEARCHING FOR MODULES ON NETWORKEnsure the modules are on the network and powered. Click on the SCAN button as shown to search for modules attached to the network.

Page 13: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The Enable Background Scan window appears. This allows for scanning to commence from node address 255 or from an address (usually 1) that you select. The Connect to Configuration station is another device available from Eurotherm for fast large volume configuration projects allowing fast un-powered configuration.

Page 14: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Once the scan is started it will find all modules on the network. This scan found a Eurotherm 2704 on serial com 4. The window shows the Browse parameter window and the Panel View picture of the module detected.

Page 15: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

If only one module is on the network or the scan has found all modules on your network, stop the background scan by again clicking on the SCAN button. This makes your system faster as the serial comms does not have to communicate to the module as well as continue searching for new equipment.

Page 16: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

VIEWS: PARAMETER VIEWThe Parameter window allow access to all module parameters for monitoring or configuration. It is selected from the drop down selection beside the Views Button.

Page 17: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Shown in the right window is the parameter view for the process variable input on the 2704. The parameters monitors the real-time information for the PV input. The OPERATOR level access which is available in this view allows the user to vary any parameter in BLACK. All parameters in BLUE are read only. In this mode variables such as the scaling factors can be altered.

Page 18: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

To access the configuration mode to allow full calibration of the PV input, the unit must be put into the configuration mode by clicking on the ACCESS button.

Page 19: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

For safety reasons in the configuration mode all the module outputs are turned off. This pop out window advises that you are about to enter the configuration mode and that control will be halted. Click yes to continue.

Page 20: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The device is in the configuration mode. Note the “Spanner” symbol indicating configuration mode. Notice also that a number of extra parameters are now available to the operator such as TYPE and LinTyp. These are only accessible in configuration mode.

Page 21: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

In this example the input type parameter has been selected (by double clicking on the variable). The pop out window has a list of variables that can be selected as the input type for this module’s input. Simply select the appropriate input and select OK.

Page 22: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

From the previous example mV has been selected. The LINTYP shows the linearisation options. Linear would be typically selected, but custom curves can also be selected.

Page 23: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

If a mV, V or mA input is selected, the operator can also choose complete scaling. IOL and IOH are the input electrical hi and lo, which are scaled to equal the values selected for VALL and VALH. The user can also select Units for the parameter, mV has been chosen but this could be any standard or custom unit.

Page 24: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

When a parameter is modified by the operator, as soon as the OK button is pressed the information is downloaded to the modules permanent memory.

Page 25: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

SOFT WIRING (2604 & 2704)In place of external wiring to configure I/O blocks, Eurotherm modules have the ability to “soft-wire” parameters. This allows the user the simplicity of internally ‘wiring’ any parameter as the input to another parameter.

Page 26: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

For example say you want to ‘wire’ the PV input to make it the source for the PID Loop 2. Double click on the parameter.

Page 27: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The pop out window allows the user to choose the appropriate link or ‘wire’ from all available parameters. Here we have scrolled down to find the PV value parameter in the PV_input list found in the Standard IO menu. Select the val tag and then click OK.

Page 28: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The scaled value on the PV input is now linked or ‘soft-wired’ as the input source parameter for the PID Loop 2.

Page 29: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

VIEWS: TOOLKIT BLOCKS (2604 & 2704)Toolkit Blocks is the term used to describe the powerful mathematics and Boolean logic capability available in the Eurotherm 2604 & 2704 controllers as well as the 2500 modular system.

Page 30: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

User values are useful as constants for alarm inputs, logic comparators or for formula constants.

Page 31: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The ANALOGUE blocks allow for almost any mathematical function. The blocks can be cascaded to provide for the most complex of calculations. Any parameter can be soft wired to the inputs allowing for infinite configuration of the module.

Page 32: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Available functions include: +, -, /, x, log, min, max, exp, sample & hold, hot swap, and logic select. Both inputs allow for scaling inputs as well as high and low output limits.

Page 33: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The logic blocks provide for any digital and Boolean expression. The blocks can be used for simple AND gates or comparisons, but can also be cascaded with the analogue blocks to allow for true hybrid control.

Page 34: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Available functions include AND, OR, XOR, Latch, =, >, <, >=, <=. For Boolean functions, both inputs can be inverted if required.

Page 35: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

As with other parameters the inputs of the parameters can be soft wired from any parameter in the same drag and drop method, or double clicking the input to reveal the pop-out parameter selection window.

Page 36: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

VIEWS: USER PAGES (2704 only)

Page 37: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The graphical screen for the high specification hybrid controller model 2704, can be configured with 8 custom screens. iTools 4.20 is now provided with a simple method of screen generation, which provides simple configuration with real-time viewing.

Page 38: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

In the configuration mode the screen is generated from one of 7 basic formats.

Page 39: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Here the screen position 10 is shown in white (selected). As per other inputs, soft-wiring allows any parameter to be wired to this alarm point. Here the selection of the output from User Alarm 2 is selected for the position 10 on the screen.

Page 40: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The position is now provided with information text providing the operator with simple to read screen information. Here the word “cell” is to be used for the position 10. Thus when the alarm is activated in this position the operator will be able to read that the ‘cell’ has a problem.

Page 41: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Only in the configuration mode can the user screen be set up. When the system is returned to the normal operator mode (by clicking on ACCESS again), then the actual screen can be seen.

Page 42: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Here is the user screen as programmed. Note that only fields that have parameters soft-wired to them will be shown.

Page 43: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

VIEWS: WATCH RECIPEWatch Recipes allow the user to monitor parameters from different sections of the parameter list on a single screen. Any parameter can be added to the watch recipe which is in effect a custom menu.

Page 44: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Simply drag any parameter from the left hand ‘explorer’ style menu to the right hand WATCH MENU window.

Page 45: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The parameter then appears in the watch menu, with the data in realtime.

Page 46: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Add as many parameters as required to the Watch window. This allows a custom menu to be developed, with parameters from any sub menu. PARAMETERS MAY ALSO BE FROM DIFFERENT MODULES ON THE NETWORK.

Page 47: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The new watch window can be saved so that it can be simply opened at a later time without the need to recreate the menu.

Page 48: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The watch window also allows for taking ‘SNAPSHOTS’ of the menu data.

Page 49: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Each time the ‘snapshot’ button is pressed a DATA SET is generated. This allows events to be captured.

Page 50: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Thus sequences of data changes can be followed for later analysis if needed.

Page 51: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

VIEWS: PROGRAMMER

Page 52: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The Programmer view allows SETPOINT Profile programs to be quickly and easily created. The graphical and ‘Excel’ styled spreadsheet format makes the segment information simple to interpret.This is the analogue view. Allowing modification of the setpoint data and any ‘wait’ events.

Page 53: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Changes to data are shown graphically to aid user comprehension. The “P_DOut” – Digital Output events for each segment can also be viewed in the analogue view.

Page 54: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

While the P_DOut events can be modified by entering the Digital view.

Page 55: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The digital view also provides both graphical and spreadsheet information. Each segment allows for up to 16 separate digital event outputs to be set. These events may be used in conjunction with or separate to the setpoint profile to control digital sequencing, capture events (utilising other logic) etc.

Page 56: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The program can be saved as a separate file for further development or for uploading to other modules.

Page 57: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

As setpoint profiling is such an important part of the control strategy and a task that is often modified, to allow for fast programming and program development, the Programmer Editor can be started as a separate program from the iTools menu.

Page 58: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The basic setpoint editor window allows for offline program modification and development independent of the module and the iTools program.

Page 59: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Stored programs can be retrieved.

Page 60: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Using the program editor in the OFFLINE mode allows extra features to be added aiding the speed of program creation and modification – such as ‘cut & paste’ and segment inserting. For example if a large existing program required the addition of new segments using existing segments at the start of the program then after selecting the appropriate segments…..

Page 61: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The segments can be copied…..

Page 62: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

And the segments can be simply ‘pasted’ into the required location.

Page 63: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The modified program can then be saved as before….

Page 64: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The program can also be uploaded to the module.

Page 65: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Up to three individual profiles can be generated.

Each profile in each segment can also have its own HOLDBACK criteria.

Page 66: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

With up to sixteen digital event outputs for each segment, and up to three WAIT events.

Page 67: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

VIEWS: OPC SCOPE (Datalogging)

The program can started in various ways. From the View menu.

Page 68: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

From the WATCH RECIPE view. Note that if started using this method, the program is automatically started with the parameters in the watch recipe.

Page 69: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The Programmer Editor can also be started as a separate program from the iTools menu.

Page 70: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The parameter tags from the same ‘explorer’ style window can be dragged & dropped into the right hand LIST window.

Page 71: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Any number of parameters can be included, and parameters from any number of modules on the network can be added.

Page 72: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The CHART CONTROL PANEL allows the datalogging to be customised. The ‘Items’ tab shows which parameters are logged on the chart.

Page 73: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The ‘Axes’ tab allows modification of the time frame and the scaling for the parameters on the chart, selecting from automatic and manual scaling.

Page 74: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Selecting the ‘CHART” tab then shows the logged values.

Page 75: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The chart logs data on the screen and can be printed. The data can also be logged to a Comma Separated Value (CSV) file, which can be opened using programs such as Excel, for later data evaluation.

Page 76: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

When the datalogging is started, a new file is started.

Page 77: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

While logging the logging toolbar button changes to reflect the logging status.

Page 78: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Press the button again to stop logging at any time.

Page 79: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The update rate of the chart and logging can also be modified from 100mS to many hours depending on the logging requirements.

Page 80: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The chart shows only the current data. However, the earlier data that has run off the end of the chart is still available as historical data that can be viewed by activating the “Enable review of historical data” feature.

Page 81: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Saving Module Configuration.

Once a module’s configuration is complete, a CLONE of the configuration can be made. The saved configuration file can be used for spares back-up and for uploading to other modules requiring identical configuration.

Page 82: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Once complete a module can be removed from the program using the REMOVE button. This can be useful if a number of modules are opened at the same time.

Page 83: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Realtime Controller Simulation & Offline Clone creation.

Page 84: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The iTools program can be used for developing configuration files offline. These interactive clone files (2200 & 2400) provide completely operational files that are not only useful for generating files for uploading, but are also highly educational training simulations for TAFE & university courses. Clone files for all Series 2000 module can be opened and configured using the “NEW File”

Page 85: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Here a new clone file of a 2404 has been opened. The iTools program has all the functions previously outlined. Note in the next couple of slides that the upper display parameter is changing. This is because a load simulation is in operation generating an interactive simulated PID control.

Page 86: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Not only does the display operate but the module control buttons are fully interactive, providing the same control as a real module. Note that if a 2404 had been scanned into iTools that this screen buttons would also operate the actual controller in the field, as if pressed on the controller.

Page 87: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The parameter list mirrors the module screen view parameters.

Page 88: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

To configure the I/O of the simulation, the user must also enter the ACCESS mode, just as would be required to configure a real module.

Page 89: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

All parameters are identical to a real module. As the clone file being generated can be uploaded later to a real module. This allows genuine offline configuration creation without the need for hardware. It also allows for experimenting with parameters without damage to attached plant.

Page 90: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The simulation can also be logged for performance evaluation, just as per a real controller.

Page 91: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

All parameters are available for logging.

Page 92: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

And just as per a real controller parameters can be changed in OPCscope. Here the setpoint is changed from 50 to 30.

Page 93: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

This graph shows the resulting simulation of the setpoint change from 50 to 30.

Page 94: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

One interesting item (which can also be useful to do during commissioning of real site equipment is to start the AUTOTUNE on the controller and log the result.

Page 95: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The resulting graph shows how the controller does an Autotune. This is useful for process evaluation as well as invaluable for education and training. The graph very clearly shows the process of autotuning, where initially the process is put into oscillation, allowing the period and amplitude of the oscillation to be measured, whereby the controller can calculate the best PID settings.

Page 96: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Once the offline configuration is complete, it can be saved to disk for later uploading to a controller. This is useful for remote sites. Allowing modifications to existing configuration files to be made remotely offline. These files can then be emailed anywhere in the world to be uploaded to the modue on site.

Page 97: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Other Programs: OPC SERVER

Available with the OPEN version of iTools, is an OPC Server. This powerful programmer allows SCADA packages to utilise OPC tags, which are far easier to implement that ModBus addressing, vastly reducing development time.

Page 98: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

As per the iTools program, modules on the network must be scanned for.

The Open Version of Eurotherm’s iTools with the OPC Server includes all of Eurotherm’s iTools Standard version, plus the server, for the less than the cost of an OPC server from other vendors

Page 99: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Once the scan is complete, the parameters are available as simple TAGS that can be simply ‘dragged & dropped’ into SCADA packages such as Wonderware and CiTech. Thus eliminating the need for ModBus addressing.

Page 100: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Parameter data can be viewed by ‘double clicking’ on the required parameter.

Page 101: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

The pop out window provides any all the TAG information as well as space for user additions. Custom TAGS can also be generated for third party modules.

Page 102: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

iTools Remote• Using iTools (and OPC Scope) to

communicate with remote instruments– i.e. not connected to a serial network attached to a

COM port on the current PC

Applications: REMOTE SITES

Remote options• ModBus serial via a modem connection • ModBus TCP • OPC over Microsoft DCOM

Page 103: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

ModBus serial via a modem connection

iTools

ModBus serial - RS485

RS232to RS485converter

OPCServer

RS2

32

RS2

32

Page 104: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

ModBus serial via modem - how to use

• Start the ModBus OPC server

• Right-click on the port, and select ‘Properties…’

Page 105: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

ModBus serial via modem - how to use cont.

• Check ‘Enable Modem Support’• Set the remaining properties as required

Page 106: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

ModBus serial via modem - when to use

• Remote diagnostics, perhaps to unmanned sites

• When the remote site has no computer or Internet connection

Page 107: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

ModBus TCPEthernet

TCP/IP

iTools

ModBus serial - RS485

ModBus TCP

ModBus TCP toModBus serial

gatewaye.g. Lantronix CoBox

OPCServer

Page 108: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

ModBus TCP - when to use

• Remote connections via Internet– smaller network overhead than DCOM– works well over dial-up networking– more likely to get through Firewalls

• When number of client connections will be small

Page 109: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

ModBus TCP - how to use• OPC server supports up to four simultaneous

connections to ModBus TCP servers• Configure through the iTools applet in the Windows

Control Panel

Page 110: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

OPC over Microsoft DCOMEthernet

TCP/IP

iToolsOPC

Server

Modbus serial - RS485

OPC/DCOM

Page 111: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

OPC over Microsoft DCOM - when to use

• Plant Ethernet connections (intranets)• When OPC clients will run on more than one

computer• Not recommended for Windows 95, 98, Me• Requires knowledge of Windows NT/2000

security

Page 112: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

OPC over Microsoft DCOM - how to use

• Optionally start OPC server on the ‘remote’ computer• Run iTools Remote on the ‘local’ computer

• Specify name or IP address of computer running OPC server

Page 113: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

OPC over Microsoft DCOM - OPC Scope

• Specify name or IP address of the remote computer before connecting

Page 114: ITools Features & Benefits CONFIGURATION, PROGRAMMING, SIMULATION & DATALOGGING SOFTWARE

Thank-you for you interest.Thank-you for you interest.If you have any questions please contact Eurotherm or visit If you have any questions please contact Eurotherm or visit

www.eurotherm.com.auwww.eurotherm.com.au

Thank-you for you interest.Thank-you for you interest.If you have any questions please contact Eurotherm or visit If you have any questions please contact Eurotherm or visit

www.eurotherm.com.auwww.eurotherm.com.au