TOP PART RUBBER SEALPUSH PLATESALIEN KEY BOLTS PREPARED BY/ ENG.
TAMER FATHY
PREPARED BY/ ENG. TAMER FATHY
PREPARED BY/ ENG. TAMER FATHY
PREPARED BY/ ENG. TAMER FATHY
WORKOVER S/R WELL WITH KTH FLANGE 1- N/D SUCKER ROD WELL HEAD.2-
M/U LANDING JT. IN TBG STRING .3- UNSCREW ALIEN KEY BOLTS 3- PULL
TILL RELEASE THE WIEGHT OF THE STRING FROM THE KTH FLANGE (P/U WT.+
PREVIOUS TENSION APPLAIED ON ANCHORE CATCHER) .4- REMOVE PUSH
PLATES & RUBBER ELEMENT 5- LIFT THE 3 SLIPS BY ITS BARS (
CONNECT ALL BARS BY A WIRE TO NOT FALL IN HOLE)6- UNSCREW THE BOLTS
OF THE KTH FLANGE AND T.H.S TO REMOVE KTH FLANGE AND RAISING SAME
UNTILL PUT TBG SLIPS ( AIR SLIPS OR BOWEL AND ROTARY SLIPS ) ABOVE
T.H.S .7- LOWER STRING IN HOLE TILL HAD STRING P/U WT. AND REMOVE
THE TENSION . AND SET THE STRING ON THE SLIPS . AND INSTALL SAFTEY
CLAMB .8- REMOVE KTH FLANGE . AND REMOVE LANDING JT. *** IN THIS
STEP IF U HAVE TBG HGR OF THE WELL HEAD INSTALL SAME IN T.H.S 9-
INSTALL BOP ABOVE T.H.S ( IF U HAVE T.BG HGR OF THE WELL HEAD WITH
DUMMY PENETRATOR IF ITS ESP WELL HEAD , U CAN TEST BOP AGIANST TBG
HGR OTHERWISE U WILL NOT ABLE TO TEST BOPS STACK EXCEPT FUNCTION
TEST ONLY .
PREPARED BY/ ENG. TAMER FATHY
PREPARED BY/ ENG. TAMER FATHY
WORKOVER S/R WELL WITH KTH FLANGE 10- PASS LANDING JT. THRU BOP
AND SCREWED SAME IN TBG .11 - UNSET TBG ANCHORE CATCHER BY STRIGHT
PULL AS PER COMPLETION ENGINEER RECOMMENDATION.**** IF THE TBG NOT
SUFFRING FROM LEAK AND COULDNT UNSET ANCHORE CATCHER BY STRIGHT
PULL , U CAN USE THE OPPOSITE WAY TO INSTALL TBG ANCHORE CATCHER BY
TAKING P/U WT. AND ROTATE STRING IN RIGHT HAND DIRECTION TILL THE
ANCHORE GET FREE .
12- POOH WITH THE OLD COMPLETION .
PREPARED BY/ ENG. TAMER FATHY
PREPARED BY/ ENG. TAMER FATHY
PLEASE READ THE NOTES BELOW EACH SLIDE *AFTER N/D BOP WHILE
HANGING STRING ON SLIPS WE PASS KTH FLAGE THRU THE TBG AND INSTALL
AND SET SAME ON T.H.S *INSTALL KTH FLANGE ABOVE T.H.S AND PUT ALL
STUDS *NOW WE WILL SET TBG ANCHORE CATCHER ON DEPTH WHILE KEEPING
SAME UNDER TENSION AS FOLLOWING:1- CALCULATE HOW MUCH TENSION WE
NEED AS STRCH IN TBG AND MARK UR MARKS IN TBG 2- LOWER STRING IN
HOLE TILL THE UPPER MARK BE ON THE TOP OF KTH FLANGE3- SET ANCHORE
CATCHER ON DEPTH BY LEFT ROTATION ( 9-11 TURNS ) TILL HAD TORQUE.4-
PULL STRING AND OBESERVE THE O.PULL OF THE STRING NOT EXCEED UNSET
SHEAR PINS OF ANCHOR CATCHER. ( AS CACULATED IT MEANS THAT THE
STRING WILL STOP WHEN LOWER MARK REACH TOP OF KTH FLANGE*NOW WE
WILL KEEP STRING IN TENSION BY PUTTING 3 SLIPS MAKE CIRCULAR AROUND
TBG BODY AND SET SAME IN KTH INTERNAL PROFILE , THEY HAVE TO BE
CONNECTED TOGETHER BY SMALL WIRE TO AVOID ANY ONE OF THEM FALL IN
HOLE . AND THERE IS 3 LIFTTING BARS TO LIFT AND PUT THEM EASILY
AROUND TBG .( SAME SAME LIKE INSTALL CSG SLIPS ). - RELEASE THE
WIEGHT OF THE STRING ON THE KTH SLIPS .*NEXT STEP IS TO SEAL AROUND
TBG STRING TO PREVENT ANY FLOW COMING FROM ANN. CSG SIDE :1- FIRST
WE PUT RUBBER ELEMENTS WHICH IS A CIRCULAR CUT FROM ONE SIDE TO CAN
ENTER AROUND TBG .2- THEN PUT PUSH PLATES ABOVE THE RUBBER ELEMNT
TO CAN PUSH AND SQUEEZ THE RUBBER AND SEAL ANN. BETWEEN TBG BODY
AND INTERNAL PROFILE OF KTH FLANGE .3- FINALLY WE PUT TOP PART
ABOVE KTH FLANGE WHICH BE FIXED BY ALIEN KEY BOLTS INTO HOLES IN
KTH FLANGE AND MORE TIGHTEN PUSH ( PUSH PLATES ) SQUEEZ THE RUBBER
AND MAKE MORE SEAL. *THE FINAL VIEW BEFORE INSTALL TOP PART WHICH
INSTALLED IN THE SHOWEN HOLES BY ALIEN KEY BOLTS.***AFTER THAT WE
REMOVE THE LANDING JOINT, KEEPING THE COLLAR ( 3 EUE COUPLING) AND
INSTALL ON IT THE SUCKER ROD WELLHEAD..
