LIVE ROLLER CONVEYOR

SPEC SHEET

CATALOG

Ul t imat ion Indust r ies LLC

15935 Stu rgeon St.

Rosev i l le, MI 48066

Ph. +1-586-771-1881

ul t imat ion inc.com

LIVE ROLLER CONVEYOR

Safety Orange

110559

RAL-2010

Machinery Grey

110652

RAL-7011

Safety Blue

110552

RAL-5019

Conveyor Blue

110549

Dark Green

110555

RAL-6005

Conveyor Gray Safety Yellow

110554

RAL-1023

Light Ivory

115174

RAL-1015

Gloss Black

111233

RAL-9005(Textured black available)

Gloss White

111232

RAL-9003

Colors illustrated below may vary slightly from actual paint colors.

Standard Paint Colors

Conveyor Green

115886

nAll safety guarding to be safety yellow unless

otherwise specified.

nOther items available, please contact factory.

nOther colors available on request

Dark Blue

114815

Light Blue

RAL-5012Sky Blue

RAL-5015

48 HO

UR

SHIP C

OLO

R

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

TABLE OF CONTENTSBELT CONVEYORS

Horizontal belt conveyor ............................................................... 1-8

Belt curve .........................................................................................9

Incline belt conveyor ..................................................................10-13

Incline dimensional chart ................................................................14

Bed and undertrussing information .................................................15

Troughed belt conveyor..............................................................16-19

LIVE ROLLER CONVEYORS

Belt driven live roller conveyor (transportation) ..........................20-21

Belt driven live roller conveyor (minimum pressure) ...................22-23

Belt driven live roller conveyor (zero pressure) ...................... 23A-23B

Flat motor conveyor (transportation) ..................................... 23C-23E

Flat motor conveyor (zero pressure) ...................................... 23F-23H

V-belt driven live roller conveyor (minimum pressure) ................24-39

Lineshaft conveyor .....................................................................40-43

Chain driven live roller conveyor (transportation) .......................44-54

CHAIN CONVEYORS

Drag chain conveyor (transportation) .........................................55-58

GRAVITY CONVEYOR

Skatewheel conveyor .................................................................59-61

Gravity roller conveyor ...............................................................62-72

Ball transfer table ...........................................................................73

Conveyor rail...................................................................................74

ACCESSORIES

Supports ....................................................................................75-78

Guide rails ......................................................................................79

Stops .........................................................................................80-82

Gates .........................................................................................83-84

ELECTRICAL CONTROLS

ProLogic Accumulation System ..................................................85-86


20

BDS19T

The BDS19T live roller conveyor is ideal for transporting

medium to heavy loads. Applications vary from manufacturing

to distribution operations.

n 11 widths

n Center drive

n Reversible

STANDARD SPECIFICATIONS

BED – 6 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder painted formed steel channel frame with 1.9 in. dia. x 16 ga. galvanized tread rollers spaced every 3 in. and 1.9 in. dia. x 16 ga. galvanized pressure rollers spaced every 6 in. Sections bolted together with butt couplings.

CROSS BRACING – Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and insure correct product tracking. Supplied on every other section, 30 ft. bed lengths and over.

DRIVE – Mounted underneath near center of conveyor in sections 7 ft.- 6 in. or longer. Center drive units are 18 in. overall width on all conveyor widths.

DRIVE BELT – Black Trackmate 120 EMB

DRIVE PULLEY – 8 in. dia. with 1 7/16 in. dia. shaft at bearings. Machine crowned and fully lagged.

TAIL PULLEY – 4 in. dia. with 1 1/8 in. dia. shaft at bearings. Machine crowned.

TAKE-UP PULLEY – 6 in. dia. with 1 3/16 in. dia. shaft at bearings. Machine crowned.

TAKE-UP – Take-up in center drive which provides 16 in. of belt take-up

SNUB IDLER – Adjustable 2 1/2 in. dia. rollers with grease packed ball bearings

RETURN IDLER – Adjustable 1.9 in. dia. rollers with grease packed ball bearings

BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys. Grease packed ball bearings in tread and pressure rollers.

CONVEYING SPEED – Constant 65 FPM

BELT DRIVEN LIVE ROLLER CONVEYOR

(1.9 in. dia. x 16 ga. rollers)

(Transportation)

CONVEYOR WEIGHT (LBS.)

OVERALL

LENGTH

BED

LENGTH

BETWEEN FRAME WIDTH

15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39"

OVERALL FRAME WIDTH

18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"

10' 8' 670 693 716 739 762 785 808 854 877 923 946

15' 13' 825 858 891 924 957 990 1,023 1,089 1,122 1,188 1,221

20' 18' 980 1,023 1,066 1,109 1,152 1,195 1,238 1,324 1,367 1,453 1,496

25' 23' 1,135 1,188 1,241 1,294 1,347 1,400 1,453 1,559 1,612 1,718 1,771

30' 28' 1,290 1,353 1,416 1,479 1,542 1,605 1,668 1,794 1,857 1,983 2,046

35' 33' 1,445 1,518 1,591 1,664 1,737 1,810 1,883 2,029 2,102 2,248 2,321

40' 38' 1,600 1,683 1,766 1,849 1,932 2,015 2,098 2,264 2,347 2,513 2,596

45' 43' 1,755 1,848 1,941 2,034 2,127 2,220 2,313 2,499 2,592 2,778 2,871

50' 48' 1,910 2,013 2,116 2,219 2,322 2,425 2,528 2,734 2,837 3,043 3,146

55' 53' 2,065 2,178 2,291 2,404 2,517 2,630 2,743 2,969 3,082 3,308 3,421

60' 58' 2,220 2,343 2,466 2,589 2,712 2,835 2,958 3,204 3,327 3,573 3,696

65' 63' 2,375 2,508 2,641 2,774 2,907 3,040 3,173 3,439 3,572 3,838 3,971

70' 68' 2,530 2,673 2,816 2,959 3,102 3,245 3,388 3,674 3,817 4,103 4,246

75' 73' 2,685 2,838 2,991 3,144 3,297 3,450 3,603 3,909 4,062 4,368 4,521

80' 78' 2,840 3,003 3,166 3,329 3,492 3,655 3,818 4,144 4,307 4,633 4,796

85' 83' 2,995 3,168 3,341 3,514 3,687 3,860 4033 4,379 4,552 4,898 5,071

90' 88' 3,150 3,333 3,516 3,699 3,882 4,065 4,248 4,614 4,797 5,163 5,346

95' 93' 3,305 3,498 3,691 3,884 4,077 4,270 4,463 4,849 5,042 5,428 5,621

100' 98' 3,460 3,663 3,866 4,069 4,272 4,475 4,678 5,084 5,287 5,693 5,896

Note: Conveyor weights are based on 3" roller centers

LOAD CAPACITY (LBS.)

BETWEENFRAME WIDTH

OVERALL LENGTH

FPM HP 10' 25' 50' 100'

35

1/213"-23" 1,500* 2,700 2,150 1,000

25"-39" 1,500* 2,350 1,400 N/A

113"-23" 1,500* 3,750* 5,500 4,300

25"-39" 1,500* 3,750* 4,800 3,100

65

1/213"-23" 1,500* 1,200 600 N/A

25"-39" 1,400 800 N/A N/A

113"-23" 1,500* 3,000 2,400 1,250

25"-39" 1,500* 2,600 1,650 N/A

213"-23" 1,500* 3,750* 6,100 4,800

25"-39" 1,500* 3,750* 5,300 3,400

120

113"-23" 1,500* 1,350 750 N/A

25"-39" 1,500* 950 100 N/A

213"-23" 1,500* 3,300 2,705 1,550

25"-39" 1,500* 2,950 2,000 100

SPEED REDUCTION – Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive shaft.

MOTOR – 1/2 HP – 230/460 – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient

CAPACITY – Maximum load per linear foot of conveyor 150 lbs. Total load NOT TO EXCEED capacity in charts.

* Limited by conveyor capacity

21


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SMS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces supplied on SMS-7 support and above.

CONVEYING SPEED – Other constant and variable speeds. Note: Capacity affected with speed change. • Underhung and side mounted drives: 25 – 120 FPM in any increment • Contact factory for speeds not listed

MOTORS – Inverter duty, premium energy efficient, single phase, brake motor and other characteristics. 2 HP maximum.

SIDE MOUNTED LOW ELEVATION CENTER DRIVE - Motor reducer unit mounted to side of conveyor. 16 in. minimum elevation.

ROLLER CENTERS – Tread rollers spaced every 2 in.

SLAVE KIT – To slave VBC19 curve from system end of belt conveyor.

GUIDE RAILS – Adjustable channel guide rail, fixed angle and channel guide rails. Note: If product comes into contact with guide rails, product flow will be affected.

PACKAGE STOPS – Fixed angle, roller or blade type stops

OTHER ACCESSORIES – Poly-tier supports, ceiling hangers. See accessory section.

ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive.

SIDE VIEW

SECTION VIEW X-X

PREFERRED

FLOW

22

BDS19M

The BDS19M live roller conveyor is ideal for transporting

or accumulating cartons, boxes or totes. Its basic design

eliminates complicated adjustments and allows a minimum

of 2% back pressure.

n 12 widths

n Minimum pressure accumulation (2% back pressure)

n Fingertip pressure roller adjustments requiring no tools

n Reversible


BED – 6 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder painted formed steel channel frame with 1.9 in. dia. x 16 ga. galvanized tread rollers spaced every 3 in. and 1.9 in. dia. x 16 ga. galvanized pressure rollers spaced every 6 in. Sections bolted together with butt couplings.

CROSS BRACING – Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and insure correct product tracking. Supplied on every other section, 30 ft. bed lengths and over.

DRIVE – Mounted underneath near center of conveyor. Center drive unit is 16 in. wide for a 16 in. overall width conveyor and 18 in. wide for all other conveyor widths.

DRIVE BELT – Black Trackmate 120 EMB

DRIVE PULLEY – 8 in. dia. with 1 7/16 in. dia. shaft at bearings. Machine crowned and fully lagged.

TAIL PULLEY – 4 in. dia. with 1 1/8 in. dia. shaft at bearings, machine crowned.

TAKE-UP PULLEY – 6 in. dia. with 1 3/16 in. dia. shaft at bearings. Machine crowned.

TAKE-UP – Take-up in center drive which provides 16 in. of belt take-up.

SNUB IDLER – Adjustable 2 1/2 in. dia. rollers with grease packed ball bearings

RETURN IDLER – Adjustable 1.9 in. dia. roller with grease packed ball bearings

BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys. Grease packed ball bearings in tread and pressure rollers.

BELT DRIVEN LIVE ROLLER CONVEYOR


(Minimum Pressure Accumulation)


OVERALL

LENGTH

BED

LENGTH

BETWEEN FRAME WIDTH

13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39"

OVERALL FRAME WIDTH

16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"

6 IN. WIDE DRIVE BELT 8 IN. WIDE DRIVE BELT

10' 8' 385 416 448 479 509 551 581 612 679 720 771 803

15' 13' 521 552 596 637 679 733 744 816 908 950 1,033 1,077

20' 18' 657 688 744 797 849 915 967 1,020 1,137 1,190 1,295 1,351

25' 23' 793 824 898 956 1,019 1,097 1,160 1,224 1,366 1,430 1,557 1,625

30' 28' 929 960 1,040 1115 1,189 1,279 1,353 1,628 1,595 1,670 1,819 1,899

35' 33' 1,065 1,096 1,188 1,274 1,359 1,461 1,546 1,632 1,824 1,910 2,081 21,73

40' 38' 1,201 1,232 1,336 1,433 1,529 1,643 1,739 1,836 2,053 2,150 2,343 2,447

45' 43' 1,337 1,368 1,484 1,592 1,699 1,825 1,935 2,040 2,282 2,390 2,605 2,721

50' 48' 1,473 1504 1,632 1,751 1,869 2,007 2,125 2,244 2,511 2,630 2,867 2,995

55' 53' 1,609 1,640 1,780 1,910 2,039 2,189 2318 2,488 2,740 2,870 3,129 3,269

60' 58' 1,745 1,776 1,928 2,069 2,209 2371 2,511 2,652 2,969 3,010 3,391 3,543

65' 63' 1,886 1,912 2,076 2,228 2,379 2,553 2,704 2,856 3,198 3,350 3,653 3,817

70' 68' 2,017 2,048 2,224 2,387 2,549 2,735 2,897 3,060 3,427 3,590 3,915 4,091

75' 73' 2,153 2,184 2,372 2,546 2,719 2,917 3,090 3,264 3,656 3,830 4,177 4,365

80' 78' 2,289 2,320 2,520 275 2,889 3,099 3,283 3,468 3,885 4,070 4,439 4,639

85' 83' 2,425 2,456 2,668 2,864 3,059 3281 3,476 3,672 4,114 4,310 4,701 4,913

90' 88' 2,561 2,592 2,816 3,023 3,229 3,463 3,669 3,876 4,343 4,550 4,963 5,187

95' 93' 2,697 2,728 2,964 3,182 3,399 3,645 3,862 4,080 4,572 4,790 5,225 5,461

100' 98' 2,833 2,864 3,112 3,341 3,569 3,827 4,055 4,284 4,801 5,030 5,487 5,735

Note: Conveyor weights are based on 3" roller centers


BETWEENFRAME WIDTH

OVERALL LENGTH

FPM HP 10' 25' 50' 100'

35

1/213"-23" 1,500* 2,700 2,150 1,000

25"-39" 1,500* 2,350 1,400 N/A

113"-23" 1,500* 3,750* 5,500 4,300

25"-39" 1,500* 3,750* 4,800 3,100

65

1/213"-23" 1,500* 1,200 600 N/A

25"-39" 1,400 800 N/A N/A

113"-23" 1,500* 3,000 2,400 1,250

25"-39" 1,500* 2,600 1,650 N/A

213"-23" 1,500* 3,750* 6,100 4,800

25"-39" 1,500* 3,750* 5,300 3,400

120

113"-23" 1,500* 1,350 750 N/A

25"-39" 1,500* 950 100 N/A

213"-23" 1,500* 3,300 2,705 1,550

25"-39" 1,500* 2,950 2,000 100



MOTOR – 1/2 HP-230/460 -3 phase – 60 Hz totally enclosed fan cooled, energy efficient

CAPACITY – Maximum load per linear foot of conveyor 150 lbs. Total load not to exceed capacity in charts.

* Limited by conveyor capacity

23


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SMS Type floor supports are available with a wide range of adjustment. Specify top of roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces supplied on SMS-7 support and above.

CONVEYING SPEED – Other constant and variable speeds. Note: Capacity and accumulation feature affected with speed change. • Underhung and side mounted drives: 25 – 120 FPM in any increment • Contact factory for speeds not listed


SIDE MOUNTED DRIVE – Motor reducer unit mounted to side of conveyor. • Low elevation end drive with underside take-up: 12 ¼ in. TOR • Center drive: 16 in. TOR

ROLLER CENTERS – Tread rollers spaced every 2 in or 4 in. (not available in 7 ft. 6 in. bed).

SLAVE KIT – To slave VBC19 curve from system end of belt conveyor.

GUIDE RAILS – Adjustable channel guide rail, fixed angle and channel guide rails. Note: If product comes into contact with guide rails, product flow will be affected.



SIDE VIEW

SECTION VIEW X-X

HOW IT WORKS:

The BDS19M is a minimum pressure conveyor meaning that product can be accumulated with a minimal amount of back pressure and horsepower. Tread rollers in contact with the product, are driven from underneath by the top surface of a drive belt running the length of the conveyor. Pressure rollers located under the belt push upward providing friction between the drive belt and the tread rollers. These pressure rollers are mounted in spring tensioned carriers that are easily adjusted with knurled finger nuts. Spring tension can be adjusted to achieve a back pressure equal to 2% of the accumulated live load.

Minmum

Back Pressure (2% of total

distributed load)

Knurled

Thumb

Adjusting

Nut

Spring Adjusted

CarrierTread Roller

PREFERRED

FLOW

24

VBS14


OVERALL LENGTH

BETWEEN FRAME WIDTH

10" 13" 16" 22"

OVERALL FRAME WIDTH

12" 15" 18" 24"

5' 183 192 200 226

10' 276 294 306 345

15' 369 399 412 467

20' 462 502 518 589

25' 555 605 624 711

30' 648 708 730 833

35' 741 811 836 955

40' 834 914 942 1,077

45' 927 1,017 1,048 1,199

50' 1,020 1,120 1,154 1,321

55' 1,113 1,223 1,260 1,443

60' 1,206 1,326 1,366 1,565

65' 1,299 1,429 1,472 1,687

70' 1,392 1,532 1,578 1,809

75' 1,485 1,635 1,684 1,931

80' 1,578 1,738 1,790 2,053

85' 1,671 1,841 1,896 2,175

90' 1,764 1,944 2,002 2,297

95' 1,857 2,047 2,108 2,419

100' 1,950 2,150 2,214 2,541

n 4 widths



n Reversible

Based on 3 in. roller centers

*50 lb/ft is limiting factor

V-BELT DRIVEN LIVE ROLLER CONVEYOR

(1 3/8 in. dia. x 18 ga. rollers)


The VBS14 live roller conveyor is ideal for transporting or

accumulating cartons, boxes or totes. Its basic design

eliminates complicated adjustments and allows a minimum of

2% back pressure.


BED – 6 1/2 in. deep x 1 in. flange x 12 ga. powder coated steel channel frame with 1 3/8 in. dia. x 18 ga. galvanized tread rollers spaced every 3 in. and 1 3/8 in. dia. x 18 ga. galvanized pressure rollers spaced every 6 in. Sections bolt together with butt couplings.

CROSS BRACING – Rods with turnbuckles are fastened to underside of bed to provide squaring adjustment and insure correct product tracking. Supplied on every other section, 30 ft. overall lengths and over.

DRIVE – Mounted underneath near center of conveyor

DRIVE BELT – Endless B-section V-belt, industrial grade

RETURN TAKE-UP SHEAVE – 3 1/4 in. dia. x 1/4 in. bore flat idler has seven position adjustment to maintain proper V-belt tension

BEARINGS – Sealed, pre-lubricated ball bearings with eccentric lock collar on flange and pillow block bearings. Grease packed ball bearings in tread and pressure rollers.



MOTOR – 1/2 HP – 230/460 3 Phase – 60 Hz totally enclosed fan cooled, energy efficient

CAPACITY – Maximum load per linear foot of conveyor 50 lbs. Not to exceed capacity in chart.


BETWEEN

FRAME WIDTH

OVERALL LENGTH

FPM HP 10' 25' 50' 100'

351/2 10"-22" 500* 1250* 2200 1600

1 10"-22" 500* 1250* 2500* 2200

651/2 10"-22" 500* 1250* 1050 200

1 10"-22" 500* 1250* 2400 1500

1201/2 10"-22" 500* 400 200 N/A

1 10"-22" 500* 1250* 1200 400

HOW IT WORKS:

The VBS14 is a minimum pressure conveyor meaning that product can be accumulated with a minimal amount of back pressure and horsepower (see photo). Tread rollers in contact with the product, are driven from underneath by the top surface of an endless V-belt running the length of each conveyor section. Pressure rollers located under the belt push upward providing friction between the V-belt and the tread rollers. These pressure rollers are mounted in spring tensioned carriers that are easily adjusted with knurled finger nuts. Spring tension can be adjusted to achieve a back pressure equal to 2% of the accumulated live load.

Minmum


distributed load)

Knurled

Thumb

Adjusting

Nut

Spring Adjusted

CarrierTread Roller

25


FLOOR SUPPORTS – SLS Type floor supports are available in a wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SLS-7 support and above.

CONVEYING SPEED – Other constant and variable speeds. Note: Capacity and accumulation feature affected with speed change. • Underhung and side mounted drives: 25 – 120 FPM in any increment • Shaft mounted drive: 25, 30, 45, 50, 65, 85 and 105 FPM nominal • Contact factory for speeds not listed


SHAFT MOUNTED DRIVE – Drive unit mounted on extended drive shaft. Mounting bracket and torque arm allow for multiple mounting positions. Minimum elevation: • Standard sheave retainer: 9 3/4 in TOR • Low elevation sheave retainer: 8 1/4 in. TOR

SIDE MOUNTED DRIVE – Motor reducer unit mounted to side of conveyor. Minimum elevation: • Standard sheave retainer: 9 3/4 in. TOR • Low elevation sheave retainer: 9 in. TOR

ROLLER CENTERS – Tread rollers spaced on 1 1/2 in. centers

PACKAGE STOPS – Roller or blade type stops available

GUIDE RAILS – Adjustable channel guide rails, fixed angle and channel guide rails. Note: If product comes in contact with guide rails, product flow will be affected.


ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible magnetic starters, push button stations, AC variable frequency drive

SHAFT MOUNTED DRIVE

CROSS SECTION A-A

SECTION VIEW Y-Y

SECTION VIEW X-X

OPTIONAL EQUIPMENT

26

VBC14

BETWEEN FRAME WIDTH

OVERALL FRAME WIDTH

"R"NUMBER OF ROLLERS WEIGHT (LBS.)

30° 45° 30° 45° 30° 45° 30° 45°

10" 12"

25" 32 36 40 32

242 252 262 272

13" 15" 248 258 268 278

16" 18" 247 267 277 287

22" 24" 272 252 292 302

n 4 widths

n Reversible

n 30, 45, 60 and 90 degree curves

V-BELT DRIVEN LIVE ROLLER CURVE


The VBC14 live roller curves are compatible with straight

sections and spurs providing flexibility to your conveyor line.

Offering a positive drive for negotiating 30°, 45°, 60°, or 90°

turns, it is available self-powered or it can be slave driven

from a straight section or spur.

PLAN VIEW – 30°, 45°, 60° AND 90° CURVE

END/SIDE VIEW

Note: Curves are non-accumulating

SECTION VIEW X-X

"BF" "OAW"

4-1/2"

20-1/8"

6-1/4"

30"

4-1/2"

"BF"

"OAW"

18" 30"

18"

"BF"

"OAW"

4-1/2"

18" 30"

18"

"BF"

"OAW"

4-1/2"

18"

30"

18"

30° 45°

60°

90°

6-1/4"

"R"

"R" “R”“R”

X

X

Y

Y

X

X

Y

Y

X

X

X

X

Y

Y

Y

Y

TAKE-UP SHEAVE

("V" TYPE)

TAKE-UP SHEAVE ("V" TYPE)



IDLER SHEAVE(FLAT TYPE) IDLER SHEAVE

(FLAT TYPE)

IDLER SHEAVE(FLAT TYPE)

SECTION VIEW Y-Y

OVERALL FRAME

WIDTH

BETWEEN FRAME

WIDTH

TREAD

ROLLER

PRESSURE SHEAVE V-BELT TAKE-UP

6-1/2"

8-3/8"

1"

27


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SLS Type floor supports are available with a wide range of adjustment. Specify top of roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces supplied on SLS-7 support and above.


MOTORS – Inverter duty, premium energy efficient, single phase, brake motor, other characteristics. 1 HP maximum.

END DRIVE – Mounted on inside radius. Minimum elevation 18-7/8 in.



BED – 6 1/2 in. deep x 1 in. flange x 12 ga. powder coated steel channel with 1 3/8 in. dia. x 18 ga. galvanized rollers

CURVES: 30, 45, 60 and 90 degree curves with 25 in. radius

COUPLINGS – Butt type for connecting to VBS14, VBCS14, and VBSS14 conveyors

END DRIVE – Mounted underneath bed section on outside radius


PRESSURE SHEAVES – 2 1/2 in. dia. with 3/8 in. bore

IDLER SHEAVE – 4 in. dia. x 5/8 in. bore V-type and/or 5 1/2 in. dia. 5/8 in. bore flat-type

SIDE MOUNTED DRIVE – Motor reducer unit mounted to side of conveyor. Minimum elevation: • Standard sheave retainer: 10 1/4 in. TOR • Low elevation sheave retainer: 9 1/2 in. TOR

GUIDE RAILS – Adjustable channel guide rails, fixed angle and channel guide rails. NOTE: If product comes in contact with guide rails, product flow will be affected

TAPERED ROLLERS – Contact factory

OTHER ACCESSORIES – Poly-tier supports, ceiling hangers. See accessory section

SLAVE DRIVEN – Standard drive may be omitted and curve can be slave driven from VBS14, VBCS14 or VBSS14. (Provide sketch showing location of slave connection.) Minimum elevation 11 in.

ELECTRICAL CONTROLS – Non-reversing or reversible magnetic starters and push-button stations, AC variable frequency drive

BEARINGS – Tread rollers have grease packed ball bearings. Flange and pillow block bearings are sealed, pre-lubricated.


SPEED REDUCTION – Sealed worm gear speed reducer with No. 50 roller chain to drive shaft

MOTOR – 1/2 HP – 230/460V-3 phase 60 Hz totally enclosed fan cooled, energy efficient

CAPACITY – 150 lbs. total distributed live load

Horsepower required to slave-drive V-belt curves from straight sections affects the maximum length of straight sections due to the capacities of the driving V-belt. The four arrangements shown. Illustrate basic slave limitations. Other arrangements are possible.

Specification Sheet – 02/02/15-R1

28

VBCS14

BETWEEN

FRAME

WIDTH

OVERALL

FRAME

WIDTH

"R""A" "B" "C" "D" "E"

NUMBER

OF ROLLERS

WEIGHT

(LBS.)

30° 45° 30° 45° 30° 45° 30° 45° 30° 45° 30° 45° 30° 45°

10" 12"

25"

32" 23" 30" 21"

33" 21" 41 1/8" 22 3/8" 44 5/8" 50 3/4" 40 36

190 182

13" 15" 38" 26" 36" 24" 194 186

16" 18" 44" 32" 42" 30" 198 190

22" 24" 56" 44" 54" 42" 45" 30" 52 3/8" 29 9/16" 50 7/16" 56 15/16 48 42 288 218

n 4 widths

n 30 or 45 degree curve spurs

n Right or left hand units available

V-BELT DRIVEN LIVE ROLLER CURVE SPUR


The Model VBCS14 curve spurs are used to transfer product

from one conveying line onto another. Offering a positive drive

for merging or diverging applications, they are available self-

powered or can be slave driven from a straight section or curve.

PLAN VIEW – 30° AND 45° CURVE SPURS

END/SIDE VIEW SECTION VIEW X-X

OVERALL FRAME

WIDTH

BETWEEN FRAME

WIDTH

TREAD

ROLLER

PRESSURE SHEAVE V-BELT TAKE-UP

6-1/2"

8-3/8"

1"

"A" "B"

"C"

"E"

31-5/8"

4-1/2"

6-1/4"

"D"

30°

60°

"R"

X

X

Y Y

TAKE-UP SHEAVE(V-TYPE)


DRIVE BELT

Y Y

"A" "B"

18"

45°

"D"

4-1/2"

31-5/8"

"E"

45°

"R"

X

X

TAKE-UP SHEAVE(V-TYPE)


DRIVE BELT

"C"

29


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SLS Type floor supports are available with a wide range of adjustment. Specify top of roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces supplied on SLS-7 support and higher.

CONVEYING SPEED – Other constant and variable speeds. Note: Capacity affected with speed change. • Underhung and side mounted drives: 25 – 120 FPM in any increment • Shaft mounted drive: 25, 30, 45, 50, 65, 85 and 105 FPM nominal • Contact factory for speeds not listed


END DRIVE – Mounted on inside radius. Minimum elevation 18-7/8 in.



BED – 6 1/2 in. deep x 1 in. flange x 12 ga. powder coated steel channel with 1 3/8 in. dia. x 18 ga. rollers

SPUR CURVES: 30 and 45 degree spur curves with 25 in. radius

COUPLINGS – Butt type for connecting VBS14 or VBC14 conveyors





BEARINGS – Tread rollers have grease packed ball bearings. Flange and pillow block bearings are sealed and pre-lubricated.



OTHER ACCESSORIES – Poly-tier supports, ceiling hangers. See accessory section

SLAVE DRIVEN – Standard drive may be omitted and curve can be slave driven from VBS14. (Specify by sketch, location of slave connection. Minimum elevation 11 in.


MOUNTING BRACKET – Bracket is supplied to attach spur to side channel of VBS14 conveyors



MOTOR – 1/2 HP –230/460V-3 phase 60Hz totally enclosed fan cooled, energy efficient


Live Roller Spurs are used to transfer product onto and off of main

conveyor lines. The illustrations below show the correct usage of

turning wheels with spurs in diverging and merging applications

DIVERGING MERGING

SPUR FLOW (SPECIFY) MOUNTING BRACKET

30

VBSS14

The Model VBSS14 straight spurs are used to transfer

product from one conveying line onto another. Offering a

positive drive for merging or diverging applications, they

are available self-powered or can be slave driven from a

straight section or curve.

BETWEEN FRAME WIDTH

OVERALL FRAME WIDTH

"A" "B" WEIGHT (LBS.)

30° 45° 30° 45° 30° 45°

10" 12" 32" 23" 30" 21" 187 162

13" 15" 38" 26" 36" 24" 193 167

16" 18" 44" 32" 42" 30" 200 172

22" 24" 56" 41" 54" 39" 206 177

n 4 widths

n 30 and 45 degree straight spurs


V-BELT DRIVEN LIVE ROLLER STRAIGHT SPUR


PLAN VIEW – 30° AND 45° STRAIGHT SPURS

SIDE VIEW Y-YSECTION VIEW X-X

X

X

Y

Y

X

X

Y

Y

31


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SLS Type floor supports are available with a wide range of adjustment. Specify top of roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces supplied on SLS-7 support and higher.



END DRIVE – Mounted underneath bed section of long rail. Minimum elevation 18-7/8 in.


DIVERGING MERGING


GUIDE RAILS – Adjustable channel guide rails, fixed angle and channel guide rails. Note: If product comes in contact with guide rails, product flow will be affected

OTHER ACCESSORIES - Poly-tier supports, ceiling hangers. See accessory section

SLAVE DRIVEN – Standard drive may be omitted and curve slave driven from VBS14 or VBC14. (Specify by sketch, location of slave connection. Minimum elevation 11 in.



BED – 6 1/2 in. deep x 1 in. flange x 12 ga. powder coated steel channel with 1 3/8 in. dia. x 18 ga. rollers

SPUR CURVES: 30 and 45 degree straight spurs

COUPLINGS – Butt type for connecting to VBS14 or VBC14 conveyors

END DRIVE – Mounted underneath bed section of short rail





MOUNTING BRACKET – Bracket is supplied to attach spur to side channel of VBS14 conveyors





Live Roller Spurs are used to transfer product onto and off of main conveyor lines. The illustrations below show the correct usage of turning wheels with spurs in diverging and merging applications


32

VBS19

The VBS19 live roller conveyor is ideal for transporting

or accumulating cartons, boxes or totes. Its basic design

eliminates complicated adjustments and allows a minimum

of 2% back pressure.

n 12 widths



n Reversible


BED – 6 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel channel frame with 1.9 in. dia. x 16 ga. galvanized tread rollers spaced every 3 in. and 1.9 in. dia. x 16 ga. galvanized pressure rollers spaced every 6 in. Sections bolt together with butt couplings.

CROSS BRACING – Rods with turnbuckles are fastened to underside of bed to provide squaring adjustment and insure correct product tracking. Supplied on every other section, 30 ft. overall lengths and over.

DRIVE – Mounted underneath near center of conveyor


RETURN TAKE-UP SHEAVES – 3 1/4 in. dia. x 1/2 in. bore flat idler has seven adjustment positions to maintain proper V-belt tension

BEARINGS – Tread and pressure rollers have grease packed ball bearings. Flange and pillow block bearings are sealed and pre-lubricated.


SPEED REDUCTION – Sealed worm gear C-Faced speed reducer with No. 50 roller chain to drive shaft

MOTOR – 1/2 HP –230/460 3 Phase - 60 Hz totally enclosed fan cooled, energy efficient

CAPACITY – Maximum load per linear foot of conveyor 150 lbs. not to exceed capacity in chart.

V-BELT DRIVEN LIVE ROLLER CONVEYOR




OVERALL

LENGTH

BETWEEN FRAME WIDTH

13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39"

OVERALL FRAME WIDTH

16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"

5' 231 238 252 263 277 289 299 314 337 351 375 387

10' 370 384 410 429 455 477 495 522 564 588 633 655

15' 509 530 568 595 633 665 691 730 791 826 891 923

20' 648 676 726 761 811 853 887 938 1,018 1,064 1,149 1,191

25' 787 822 884 927 989 1,041 1,083 1,146 1,245 1,302 1,407 1,459

30' 926 968 1,042 1,093 1,167 1,229 1,279 1,354 1,472 1,546 1,665 1,727

35' 1,065 1,114 1,200 1,259 1,345 1,417 1,475 1,562 1,699 1,778 1,923 1,995

40' 1,204 1,260 1,358 1,425 1,523 1,605 1,671 1,770 1,926 2,016 2,181 2,263

45' 1,343 1,406 1,516 1,591 1,701 1,793 1,867 1,978 2,153 2,254 2,439 2,531

50' 1,482 1,552 1,674 1,757 1,879 1,981 2,063 2,186 2,380 2,492 2,697 2,799

55' 1,621 1,698 1,832 1,923 2,057 2,169 2,259 2,394 2,607 2,731 2,955 3,067

60' 1,760 1,844 1990 2,089 2,235 2,357 2,455 2,602 2,834 2,969 3,213 3,335

65' 1,899 1,990 2148 2,255 2,413 2,545 2,651 2,810 3,061 3,207 3,471 3,603

70' 2,038 2,136 2306 2,421 2,591 2,733 2,847 3,018 3,288 3,445 3,728 3,871

75' 2,177 2,282 2,464 2,587 2,769 2,921 3,043 3,226 3,515 3,683 3,987 4,139

80' 2,316 2,428 2622 2,753 2,947 3,109 3,239 3,434 3,742 3,921 4,243 4,407

85' 2,455 2,574 2,780 2,919 3,125 3,297 3,435 3,642 3,969 4,158 4,502 4,675

90' 2,594 2,720 2,938 3,085 3,303 3,485 3,631 3,850 4,196 4,396 4,761 4,943

95' 2,733 2,866 3,096 3,251 3,481 3,673 3,827 4,058 4,423 4,634 5,019 5,211

100' 2,872 3,012 3,254 3,417 3,659 3,861 4,023 4,266 4,650 4,872 5,277 5,479


BETWEENFRAME WIDTH

OVERALL LENGTH

FPM HP 10' 25' 50' 100'

35

1/213"-23" 1,500* 3,150 2,700 2,200

25"-39" 1,500* 2,850 2,500 1,250

113"-23" 1,500* 3,750* 4,500 4,500

25"-39" 1,500* 3,750* 3,900 2,600

65

1/213"-23" 1,500* 1,400 1,050 200

25"-39" 1,500* 1,200 550 NA

113"-23" 1,500* 3,700 3,300 2,100

25"-39" 1,500* 3,500 2,850 1,500

213"-23" 1,500* 3,750* 4,500 3,750

25"-39" 1,500* 3,750* 3,950 2,650

100

1/213"-23" 850 600 200 NA

25"-39" 750 350 NA NA

113"-23" 1,500* 1,650 1,200 400

25"-39" 1,500* 1,400 700 NA

213"-23" 1,500* 3,700 3,300 2,500

25"-39" 1,500* 3,500 2,800 1,500

*Limited by conveyor capacity

33


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SMS Type floor supports are available in a wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-7 support and above.





ROLLER CENTERS – Tread rollers spaced on 2 in. or 4 in. centers. (Not available in 7 ft. 6 in. bed)

PACKAGE STOPS – Fixed angle, roller or blade type stops available




SECTION VIEW X-XSHAFT MOUNTED DRIVE

HOW IT WORKS:

The VBS19 is a minimum pressure conveyor meaning that product can be accumulated with a minimal amount of back pressure and horsepower (see photo). Tread rollers in contact with the product, are driven from underneath by the top surface of an endless V-belt running the length of each conveyor section. Pressure rollers located under the belt push upward providing friction between the V-belt and the tread rollers. These pressure rollers are mounted in spring tensioned carriers that are easily adjusted with knurled finger nuts. Spring tension can be adjusted to achieve a back pressure equal to 2% of the accumulated live load.

X

X

Y

Y

RETURN / TAKE-UP SHEAVE

SECTION VIEW Y-Y

Minmum


distributed load)

Knurled

Thumb

Adjusting

Nut

Spring Adjusted

CarrierTread Roller

34

VBC19

The VBC19 live roller curves are compatible with straight

sections and spurs providing flexibility to your conveyor line.

They are available self-powered or can be slave driven from

a straight section or spur.

*T= Tapered, S- Straight

BETWEEN FRAME WIDTH

OVERALL FRAME WIDTH

"R"NUMBER OF ROLLERS * WEIGHT (LBS.)

30° 45° 60° 90° 30° 45° 60° 90°

13" 16" 24" 5T/12S 8T/12S 10T/12S 16T/4S 317 323 330 336

15" 18"

32-1/2" 7T/12S 10T/12S 14T/12S 20T/4S

300 336 343 349

17" 20" 343 350 357 364

19" 22" 357 364 371 378

21" 24" 371 378 386 393

23" 26" 386 393 401 408

25" 28" 401 409 417 425

27" 30" 417 425 434 442

31" 34

48" 10T/12S 14T/12S 22T/12S 30T/4S

529 540 551 562

33" 36" 550 562 573 585

37" 40" 589 601 613 625

39" 42" 612 625 638 651

n 12 widths

n Reversible

n Tapered tread rollers

n 30, 45, 60 and 90 degree curves

V-BELT DRIVEN LIVE ROLLER CURVE


PLAN VIEW – 30°, 45°, 60° AND 90° CURVES

END/SIDE VIEW

10-5/16"

4-1/4"

3-1/2"

TOTALLY

ENCLOSED

CHAIN GUARDOPTIONAL SMS

SUPPORTS SHOWN

SECTION VIEW Y-YSECTION VIEW X-X

Note: Curves are non-accumulating

35


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SMS floor supports are available with a wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at the ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-7 support and above.


END DRIVE – Mounted on inside radius. Minimum elevation 18 7/8 in.

SHAFT MOUNTED DRIVE – Drive unit mounted on extended drive shaft. Mounting bracket and torque arm allow for multiple mounting positions. Minimum elevation: • Standard sheave retainer: 10 1/4 in. TOR • Low elevation sheave retainer: 8 3/4 in. TOR



BED – 6 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel channel with 2 1/2 in. dia. tapered to 1 11/16 in. dia. x 14 ga. galvanized rollers. 1.9 in. dia. x 16 ga. galvanized rollers provided in tangent sections.

CURVES – 30, 45, 60 and 90 degree curves. 24 in., 32 1/2 in. or 48 in. radius dependent upon between frame widths.

COUPLINGS – Butt type for connecting to VBS19, VBCS19, VBSS19, BDS19T or BDS19M conveyors



POSITIVE DRIVE PRESSURE SHEAVES – 2 1/2 in. dia. with 3/8 in. bore.

IDLER SHEAVE – 4 in. dia. x 5/8 in. bore V-type and/or 5 in. dia. 5/8 in. bore flat-type.

Horsepower required to slave-drive V-belt curves from straight sections affects the maximum length of straight sections due to the capacity of the driving V-Belt. The four arrangements shown, illustrate basic slave limitations. Other arrangements are possible.



SLAVE DRIVEN – Omit standard drive and slave drive curve from VBS19, VBCS19, VBSS19, BDS19T, or BDS19M conveyors. Minimum elevation 11 in. (Provide sketch illustrating location of slave connection).


ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters and push-button stations, AC variable frequency drive

TAKE-UP SHEAVE – 4 3/8 in. dia. x 5/8 in. bore V-type sheave to maintain proper V-belt tension

BEARINGS – Tread rollers have grease packed ball bearings. Flange and pillow block bearings are sealed, pre-lubricated.



MOTOR – 1/2 HP – 230/460V-3 phase 60 Hz totally enclosed fan cooled, energy efficient


36

VBCS19

The Model VBCS19 curve spurs are used to transfer product

from one conveying line onto another. Suitable for merging

or diverging applications, they are available self-powered or

can be slave driven from a straight section or curve.


BETWEEN FRAME WIDTH

OVERALL FRAME WIDTH

"R""A" "B" "C" "D" "E"

TOTAL NUMBER OF ROLLERS *

WEIGHT (LBS.)

30° 45° 30° 45° 30° 45° 60° 90° 30° 45° 30° 45° 30° 45°

13" 16" 24" 38" 29" 36" 27" 30" 21" 38" 21-7/8" 42-1/4" 50" 12S/10T 13S/8T 206 195

15" 18"

32-1/2"

41" 32" 39" 30"

54" 36" 63" 35" 61-5/8" 66-5/8" 20S/14T 18S/10T

245 224

17" 20" 47" 35" 45" 33" 255 233

19" 22" 50" 38" 48" 36" 264 241

21" 24" 53" 41" 51" 39" 270 250

23" 26" 56" 44" 54" 42" 287 262

25" 28" 62" 47" 60" 45" 299 276

27" 30" 65" 50" 63" 48" 311 282

31" 34

48"

74" 56" 72" 54"

75" 48" 89" 48" 58-1/2" 86-1/16" 27S/22T 22S/14T

380 322

33" 36" 77" 59" 75" 57" 390 329

37" 40" 86" 65" 84" 63" 406 340

39" 42" 89" 68" 87" 66" 416 351

n 12 widths

n 30 and 45 degree curve spurs


Note: Curve spurs are non-accumulating

V-BELT DRIVEN LIVE ROLLER CURVE SPUR


X

X

-

-

X

X

PLAN VIEW – 30° AND 45° CURVE SPURS

END/SIDE VIEW SECTION VIEW X-X

37


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SMS Type floor supports are available with a wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at the ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-7 support and above.

CONVEYING SPEED – Other constant and variable speeds. Note: Capacity affected with speed change. • Underhung and side mounted drives: 25 – 120 FPM in any increment • Shaft mounted drive: 25, 30, 45, 50, 65, 85, and 105 FPM nominal • Contact factory for speeds not listed

END DRIVE – Mounted on inside radius. Minimum elevation 18 7/8 in. TOR.

SHAFT MOUNTED DRIVE – Drive unit mounted on extended drive shaft. Mounting bracket and torque arm allow for multiple mounting positions. Minimum elevation: • Standard sheave retainer: 10 1/4 in. TOR • Low elevation sheave retainer: 8 3/4 in. TOR

DIVERGING



BED – 6 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel channel with 2 1/2 in. dia. tapered to 1 11/16 in. dia. x 14 ga. galvanized rollers. 1.9 in. dia. x 16 ga. galvanized rollers provided in tangent sections.

SPUR CURVES: 30 and 45 degree spur curves. 24 in., 32 1/2 in. or 48 in. radius dependent upon between frame widths.

COUPLINGS – Butt type for connecting to VBS19, VBC19, BDS19T or BDS19M conveyors



POSITIVE DRIVE PRESSURE SHEAVES – 2 1/2 in. dia. with 3/8 in. bore

IDLER SHEAVE – 4 in. dia. x 5/8 in. bore V-type and/or 5 in. dia. 5/8 in. bore flat-type

TAKE-UP SHEAVE – 4 3/8 in. dia. x 5/8 in. bore V-type sheave to maintain proper V-belt tension.


MOUNTING BRACKET – Bracket is supplied to attach spur to side channel of a VBS19, BDS19T or BDS19M conveyors.

CONVEYING SPEED – Constant 65 FPM.

SPEED REDUCTION – Sealed worm gear speed reducer with No. 50 roller chain to drive shaft.


CAPACITY – 500 lbs. total distributed live load.

MERGING



OTHER ACCESSORIES - Poly-tier supports, ceiling hangers. See accessory section.

SLAVE DRIVEN – Omit standard drive and slave drive curve spur from VBS19, VBC19, BDS19M, or BDS19T conveyors. Minimum elevation 11 in. (Provide sketch illustrating location of slave connection).


ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing or reversible IEC starters and push-button stations, AC variable frequency drive

Live roller spurs are used to transfer product onto and off of main conveyor lines. The illustrations below show the correct usage of turning wheels and plow arms with spurs in diverging and merging applications.

RIGHT HAND LEFT HAND

38

VBSS19

The Model VBSS19 straight spurs are used to transfer

product from one conveying line onto another. Suitable

for merging or diverging applications, they are available

self-powered or can be slave driven from a straight section

or curve.


BETWEEN FRAME WIDTH

OVERALL FRAME WIDTH

"A" "B" WEIGHT (LBS.)

30° 45° 30° 45° 30° 45°

13" 16" 38" 29" 36" 27" 202 176

15" 18" 41" 32" 39" 30" 210 179

17" 20" 47" 35" 45" 33" 214 182

19" 22" 50" 38" 48" 36" 216 185

21" 24" 53" 41" 51" 39" 219 188

23" 26" 56" 44" 54" 42" 222 191

25" 28" 62" 47" 60" 45" 224 194

27" 30" 65" 50" 63" 48" 227 198

31" 34 74" 56" 72" 54" 230 201

33" 36" 77" 59" 75" 57" 235 208

37" 40" 86" 65" 84" 63" 239 212

39" 42" 89" 68" 87" 66" 243 216

n 12 widths



V-BELT DRIVEN LIVE ROLLER STRAIGHT SPURS


PLAN VIEW – 30°, 45° STRAIGHT SPURS

SIDE VIEW Y-YSECTION VIEW X-X

X

Y

Y

X

4-1/2"

Y

Y

X

X

Note: Curve spurs are non-accumulating

39


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – SMS Type floor supports are available with a wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at the ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-7 support and above.

BED LENGTHS – 57 in., 63 in., 69 in., 75 in., 81 in., and 87 in. Drive not available on all lengths and widths. Contact factory

CONVEYING SPEED – Other constant and variable speeds. Note: Capacity affected with speed change. • Underhung and side mounted drives: 25 – 120 FPM in any increment • Shaft mounted drive: 25, 30, 45, 50, 65, 85, and 105 FPM nominal • Contact factory for speeds not listed

SHAFT MOUNTED DRIVE – Motor reducer unit mounted on extended drive shaft. Mounting bracket and torque arm allow for multiple mounting positions. Minimum elevation: • Standard sheave retainer: 10 1/4 in. TOR • Low elevation sheave retainer: 8 3/4 in. TOR

DIVERGING MERGING


GUIDE RAILS – Adjustable channel guide rails, fixed angle and channel guide rails. Note: If product comes in contact with guard rails, product flow will be affected.

OTHER ACCESSORIES - Poly-tier supports, ceiling hangers. See accessory section.

SLAVE DRIVEN – Omit standard drive and slave drive straight spur from VBS19, VBC19, BSD19M or BSD19T conveyors. Minimum elevation 11 in. (Provide sketch illustrating location of slave connection).


ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing or reversible IEC starters and push-button stations, AC variable frequency drive

Live roller spurs are used to transfer product onto and off of main conveyor lines. The illustrations below show the correct usage of turning wheels and plow arms with spurs in diverging and merging applications.


BED – 6 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel channel with 1.9 in. dia. x 16 ga. galvanized tread rollers spaced every 3 in.

STRAIGHT SPUR: 30 and 45 degree straight spurs

COUPLINGS – Butt type for connecting to VBS19, VBC19, BDS19T or BDS19M conveyors

END DRIVE – Mounted underneath bed section of short rail


POSITIVE DRIVE PRESSURE SHEAVES – 2 1/2 in. dia. with 3/8 in. bore

SNUB RETURN SHEAVE – 4 in. dia. x 5/8 in. bore V type and/or 4 5/8 in. dia. x 5/8 in. bore flat type

TAKE-UP – Take-ups provided to maintain proper V-belt tension


MOUNTING BRACKET – Bracket is supplied to attach spur to side channels of a VBS19, BDS19T or BDS19M conveyors


SPEED REDUCTION – Sealed worm gear speed reducer with No. 50 chain to drive shaft

MOTOR – 1/2 HP – 230/460V – 3 phase 60Hz. totally enclosed fan cooled, energy efficient




40

LSS19

The model LSS19 live roller conveyor is ideal for transporting

or accumulating products. Its unique design allows product

to accumulate with only minimal back pressure.

CONVEYOR WEIGHTS (LBS.)

OVERALL

LENGTH

BETWEEN FRAME WIDTH

13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39"

OVERALL WIDTH

16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"

5' 184 190 198 205 213 219 227 234 248 256 271 277

10' 292 304 318 332 346 359 373 387 413 427 455 468

15' 400 418 439 859 479 498 519 539 578 599 640 658

20' 507 532 560 586 613 638 665 692 743 770 824 849

25' 615 646 680 713 747 777 811 844 908 942 1009 1039

30' 724 760 800 840 880 917 957 997 1073 1113 1193 1230

35' 832 874 921 967 1014 1056 1103 1149 1238 1285 1378 1420

40' 940 988 1041 1094 1147 1196 1249 1302 1403 1456 1562 1611

45' 1048 1102 1162 1221 1281 1335 1395 1454 1568 1628 1747 1801

50' 1156 1216 1282 1348 1414 1475 1541 1607 1733 1799 1931 1992

55' 1264 1330 1402 1475 1547 1614 1687 1759 1898 1971 2116 2182

60' 1372 1444 1523 1602 1681 1754 1833 1912 2063 2142 2300 2373

65' 1478 1559 1643 1729 1815 1893 1979 2064 2228 2314 2485 2563

70' 1588 1673 1764 1856 1948 2033 2125 2217 2393 2485 2669 2754

75' 1696 1787 1885 1983 2082 2172 2271 2369 2558 2657 2854 2944

80' 1804 1900 2005 2110 2215 2312 2417 2522 2723 2828 3038 3135

85' 1912 2015 2126 2237 2349 2451 7563 2674 2888 3000 3223 3325

90' 2020 2129 2246 2364 2482 2591 2709 2827 3053 3171 3407 3516

95' 2128 2243 2367 2491 2616 2730 2855 2979 3218 3343 3592 3706

100' 2236 2357 2487 2618 2749 2870 3001 3132 3383 3514 3776 3897

n 12 widths

n Minimum pressure accumulation

n Quiet operation

STANDARD SPECIFICATIONSBETWEEN

FRAME WIDTH

LOAD CAPACITY CHART (LBS.)

OVERALL LENGTH

FPM HP 10' 25' 50' 100'

301/2

13"-39"500 1250 2500 N/A

1 500 1250 2500 5000

60

1/2

13"-39"

500 1250 N/A N/A

1 500 1250 2500 N/A

2 500 1250 2500 5000

90

1/2

13"-39"

500 1250 N/A N/A

1 500 1250 2500 N/A

2 500 1250 2500 5000

LINESHAFT DRIVEN LIVE ROLLER CONVEYOR

(1.9 in. dia. X 16 ga. Galvanized rollers)


BED - 5 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder painted coated steel channel frame with 1.9 in. dia. x 16 ga. galvanized tread rollers spaced every 3 in. Sections bolted together with butt couplings.

COUPLINGS - Butt type for connecting to LSC19 or LSSS19 conveyors

CROSS BRACING - Rods with turnbuckles are fastened to underside of bed to provide squaring adjustment and insure correct product tracking. Supplied on every other section, 30 ft. overall lengths and over.

DRIVE - Mounted underneath of conveyor. Note: Motor extends beyond frame of conveyor if between frame width is less than 20 inches

DRIVE SHAFT - 1 in. dia. steel shaft full length of conveyor. Shafts are coupled together by a Delrin chain coupling at each bed joint.

DRIVE SPOOLS - 2 in. Delrin spool held in place on shaft by "snap-on" retaining clips

DRIVE BELTS - 3/16 in. dia. urethane belts from drive spools to rollers

SPOOL GUARD - Encloses underside of drive shaft, spools and drive belts. Full length of conveyor.

BEARINGS - Sealed, self-aligning, pre-lubricated ball bearings support drive shaft

CONVEYING SPEED - Constant 60 FPM

SPEED REDUCTION - Sealed worm gear C-Faced speed reducer with No. 50 roller chain to drive shaft

MOTOR - 1/2 HP –230/460 3 Phase - 60 Hz totally enclosed fan cooled, energy efficient

CAPACITY - Maximum load per roller is 15 lbs. with a maximum individual product load of 75 lbs. Maximum driven length with single drive at center is 120 ft. Not to exceed capacity in chart.

41


OPTIONAL EQUIPMENT

FLOOR SUPPORTS - H-style floor supports are available with a wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at the ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on MHST-9 support and above.

CONVEYING SPEED - Constant and variable speeds from 30 to 120 FPM. Contact factory for speeds not listed.

MOTORS - Inverter duty, premium energy efficient, single phase, 2 HP maximum

SIDE MOUNTED DRIVE - Motor reducer unit mounted to side of conveyor. Minimum elevation: 11 3/4 in. TOR

TIMING BELT DRIVE – Option to chain drive allowing for quieter operation. Required at speeds of 120 FPM and greater.

ROLLER CENTERS - 2 in., 4 in., 6 in. and 8 in. roller centers are also available

POSITIVE DRIVE – Keyed spools and drive shaft provide positive drive

POWER CROSSOVER – 1 ft. long section that switches drive shaft from one side of the conveyor to the other. Can also be used to increase/decrease speed.

PNEUMATIC ROLLER BRAKE – Air operated conveyor accessory that stops rollers in 2 ft. or 3 ft. zones

BLADE STOPS – Pneumatically or manually operated blade that pops up between rollers in order to accumulate product

SPRING BALANCED GATE – 6 ft. section consisting of 2 ft. fixed section and 4 ft. gate section

OTHER ACCESSORIES – Stops, poly-tier supports, ceiling hangers, traffic cop, belt transfer

ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive

OVERALL LENGTH

1' TO 10' SLAVED

SECTION(S)

2' TO 10' DRIVE SECTION

21-1/4" MIN. TOR

18-7/16"

14-1/4"

SPOOL GUARD

FLOW

Retaining Clip Drive Shaft

Drive Belt

Tread Roller

Drive Spool

HOW IT WORKS

The LSS19 is a minimum pressure conveyor meaning that product can be accumulated with a minimal amount of back pressure and horsepower. A drive shaft spanning the length of the conveyor transmits power to the tread rollers though drive spools and drive belts. If back pressure (accumulation) is applied, the drive spool will slip on the drive shaft, stopping power to the tread roller.

1-1/2"

1/4"2-3/4"

5-1/2"

2"

4-7/8"

42

LSC19The LSC19 live roller curves are compatible with straight

sections and spurs providing flexibility to your conveyor

line. They are slave driven from an adjacent

lineshaft conveyor straight section.

BETWEEN FRAME WIDTH

OVERALL FRAME WIDTH

INSIDERADIUS

ROLLERS"PER 90° CURVE"

WEIGHT (LBS.)

30° 45° 60° 90°

13" 16"

36"

24

Tapered

Rollers

126 89 121 194

15" 18" 132 93 127 203

17" 20" 140 99 136 214

19" 22" 146 104 142 223

21" 24" 152 108 148 233

23" 26" 158 113 155 242

25" 28" 164 117 161 251

27" 30" 170 122 168 260

31" 34" 183 131 181 279

33" 36" 182 136 187 288

37" 40" 195 145 200 306

39" 42" 201 150 206 315

n 12 widths

n Tapered tread rollers

n 30, 45, 60, and 90 degree curves

LINESHAFT DRIVEN LIVE ROLLER CURVE

PLAN VIEW – 30° AND 45° STRAIGHT SPURS

30° and 60° curves are also available. 30° curves have 12" tangent section on both ends.


BED - 5 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel channel frame with with 2-1/2 in. dia. tapered to 1-11/16 in. dia. x 14 ga. galvanized rollers. 1.9 in. dia. x 16 ga. galvanized rollers provided in tangent sections.

CURVES - 30, 45, 60 and 90 degree curves with 36 in. radius

COUPLINGS - Butt type for connecting to other lineshaft conveyor sections

SLAVE DRIVEN - Spurs are slave driven from the drive shaft of adjacent lineshaft conveyor section. Shafts are coupled together by a Delrin chain coupling at the bed joints.

DRIVE SHAFT - 1 in. dia. steel shaft with universal joints as necessary

DRIVE SPOOLS - 2 in. dia. Delrin spool held in place on shaft by "snap-on" retaining clips


SPOOL GUARD - Encloses underside of drive shaft, spools and drive belts


CAPACITY - Maximum of 15 lbs. per roller. Do not exceed a 75 lb. total product load.

OPTIONAL EQUIPMENT

FLOOR SUPPORTS – H-style floor supports are available with a wide range of adjustments. Specify top of roller elevation. For curves, one support is required at each end along with one single support at the center. For spurs, one support is required at bed joint. Holes in feet are provided for lagging to floor. Knee braces supplied on MHST-9 support and above.

DRIVE – Drive units can be mounted to curves rather than being slave driven

TANGENTS – Short straight section on one or both ends of curve

GUIDE RAILS – Adjustable channel guide rails, fixed angle, and channel guide rails. One or both sides. Note: If product contacts guide rails, product flow may be affected.

OTHER ACCESSORIES – Poly-tier supports, ceiling hangers, plow arm, traffic cop, turning wheel

1-1/2"

1/4"2-3/4"

5-1/2"

2"

43


LSSS19

The LS19 live roller curves are used to transfer product

from one conveying line onto another. Suitable for merging

or diverging applications, they are available self-powered or

can be slave driven from a straight section or curve.

30° SPUR 45° SPUR

BETWEEN FRAME WIDTH

"A" "B" "C"WT.

(LBS.)"A" "B" "C"

WT. (LBS.)

13" 30 11/16" 36" 12" 32 28 1/8" 36" 21" 37

15" 37 3/4" 48" 21" 49 28 1/8" 36" 21" 40

17" 44 11/16" 48" 15" 48 32 3/8" 36" 18" 40

19" 44 11/16" 48" 12" 49 36 9/16" 36" 15" 40

21" 53 1/2" 60" 21" 70 36 9/16" 36" 15" 44

23" 53 1/2" 60" 18" 71 40 13/16" 36" 12" 43

25" 58 9/16" 60" 15" 72 45 1/16" 48" 21" 65

27" 58 9/16" 60" 12" 73 45 1/16" 48" 21" 70

31" 72 3/8" 72" 15" 97 53 9/16" 48" 15" 68

33" 72 3/8" 72" 12" 98 53 9/16" 48" 15" 73

37" 81 1/16" 84" 18" 129 62 1/16" 60" 21" 100

39" 84 1/2" 84" 15" 130 62 1/16" 60" 21" 106

n 12 widths



LINESHAFT DRIVEN LIVE ROLLER

STRAIGHT SPUR

“A”

“B”

“C”

SHAFT

COUPLING

DRIVE

SHAFT

45º

SPUR FLOW (SPECIFY)

PLAN VIEW – 30°, 45° STRAIGHT SPURS


BED - 5 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel channel frame with with 2 1/2 in. dia. tapered to 1 11/16 in. dia. x 14 ga. galvanized rollers. 1.9 in. dia. x 16 ga. galvanized rollers provided in tangent sections.

STRAIGHT SPURS - 30 and 45 degree

COUPLINGS - Butt type for connecting to other lineshaft conveyor sections

SLAVE DRIVEN - Spurs are slave driven from the drive shaft of adjacent lineshaft conveyor section. Shafts are coupled together by a Delrin chain coupling at the bed joints.

DRIVE SHAFT - 1 in. dia. steel shaft with universal joints as necessary

DRIVE SPOOLS - 2 in. dia. Delrin spool held in place on shaft by "snap-on" retaining clips


SPOOL GUARD - Encloses underside of drive shaft, spools and drive belts


CAPACITY - Maximum of 15 lbs. per roller. Do not exceed a 75 lbs. total product load

OPTIONAL EQUIPMENT

FLOOR SUPPORTS – H-style floor supports are available with a wide range of adjustments. Specify top of roller elevation. For curves, one support is required at each end along with one single support at the center. For spurs, one support is required at bed joint. Holes in feet are provided for lagging to floor. Knee braces supplied on MHST-9 support and above.

DRIVE – Drive units can be mounted to curves rather than being slave driven

GUIDE RAILS – Adjustable channel guide rails, fixed angle, and channel guide rails. One or both sides. Note: If product contacts guide rails, product flow may be affected.

OTHER ACCESSORIES – Poly-tier supports, ceiling hangers, plow arm, traffic cop, turning wheel.


44


CDS19

The CDS19 chain driven live roller is ideal for handling

medium loads such as totes, wheels and empty drums.

Roll-to-roll chain driven rollers provide positive drive making

it ideal for oily conditions that are not suitable for belt driven

live roller.


CONVEYING SURFACE WIDTH

12 1/4" 14 1/4" 16 1/4" 18 1/4" 20 1/4" 22 1/4" 24 1/4" 28 1/4" 30 1/4" 34 1/4" 36 1/4"

BETWEEN FRAME WIDTH

15 1/2" 17 1/2" 19 1/2" 21 1/2" 23 1/2" 25 1/2" 27 1/2" 31 1/2" 33 1/2" 37 1/2" 39 1/2"

CHAIN

SIZE

OVERALL WIDTH

18 1/2" 20 1/2" 22 1/2" 24 1/2" 26 1/2" 28 1/2" 30 1/2" 34 1/2" 36 1/2" 40 1/2" 42 1/2"

4" CENTER 10 ' LENGTH

NO. 40

CHAIN

454 480 506 529 555 581 604 656 682 731 757

PER FOOT 36 39 41 44 46 48 51 55 58 62 65

6" CENTER 10 ' LENGTH 381 399 417 433 451 469 485 521 539 573 591

PER FOOT 29 31 32 34 35 37 38 42 43 46 48

n Roll-to-roll chain drive

n 11 widths

n Reversible


BED – 5 in. deep x 1 1/2 in. flange x 1/4 in. channel on drive side. 3 1/2 in. deep x 1 1/2 in. flange x 1/4 in. channel on idler side. Powder coated. 1.9 in. dia. x .145 wall unplated tread rollers spaced on 4 in. or 6 in. centers. Rollers are above frame on idler side.

CENTER DRIVE – Underhung drive with outboard chain guard

ROLLER-TO-ROLLER CHAIN – No. 40 chain

DRIVE CHAIN – No. 60 chain

CHAIN GUARD – Formed steel upper and lower chain guard mounted to drive side channel frame to totally enclose drive chains

BEARINGS – Sealed, pre-lubricated, ball bearings

SPEED REDUCTION – Sealed worm gear C-face speed reducer

MOTOR – 1/2 HP – 230/460V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient


FRAME CAPACITY – Maximum load per linear foot of conveyor is 150 lbs. with supports on 10 ft. centers, 250 lbs. with supports on 5 ft. centers. Not to exceed drive capacity in chart.


CONVEYING

SURFACE WIDTH

LENGTH

FPM HP 25' 50' 75'

15

1/212 1/4" - 20 1/4" 2125† 4250† 6375†

22 1/4" - 36 1/4" 2125† 4250† 6375†

112 1/4" - 20 1/4" 2125† 4250† 6375†

22 1/4" - 36 1/4" 2125† 4250† 6375†

30

1/212 1/4" - 20 1/4" 2125† 4250† 6005

22 1/4" - 36 1/4" 2125† 4250† 5420

112 1/4" - 20 1/4" 2125† 4250† 6375†

22 1/4" - 36 1/4" 2125† 4250† 6375†

45

112 1/4" - 20 1/4" 2125† 4185 3835

22 1/4" - 36 1/4" 2125† 3790 3245

212 1/4" - 20 1/4" 2125† 4250† 6375†

22 1/4" - 36 1/4" 2125† 4250† 6300*

Based on 6 in. roller centers and supports on 10 ft. centers*Chain is limiting factor†Frame is limiting factor

CHAIN DRIVEN LIVE ROLLER CONVEYOR

(1.9 in. dia. x .145 wall rollers)

11-1/4"

X

X

45


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – Floor supports are available in wide range of adjustments. Specify top of roller elevations. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied above 36 in. top of roller.

CONVEYING SPEEDS – Other constant and variable speeds available from 15-75 FPM in any increment. Contact factory for speeds outside this range.


DRIVE VARIATIONS – Side mount high or low drives

ROLLERS SET LOW – 5 in. deep x 1 1/2 in. flange x 1/4 in. channel frame on drive side and idler side

CHAIN CROSS-OVER – Transfers power from one side to the other

TRANSFERS – Right angle chain transfers available

ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible starters and push button stations. AC variable frequency drive.

OTHER ACCESSORIES – Poly-tier supports, ceiling hangers

ROLLERS LOW BOTH SIDES OPTIONSECTION VIEW X-X (ROLLERS HIGH/LOW)

5"

11-1/4"

1-3/8"

CONVEYING

SURFACE

BETWEEN FRAME

OVERALL WIDTH 2-3/4"

5" 5"

11-1/4"

3-1/2"

3/16" 1-3/8"

CONVEYING

SURFACE

BETWEEN FRAME

2-3/4" OVERALL WIDTH

46


CDC19

The CDC19 chain driven live roller curves are compatible

with straight sections and provide flexibility to your conveyor

line. They are available self-powered or can be slave driven

from a straight section.

n 11 widths

n Straight rollers


n Can be slave driven

from CDS19


BED – 5 in. deep x 1 1/2 in. flange x 1/4 in. channel on drive side. 3 1/2 in. deep x 1 1/2 in. flange x 1/4 in. channel on idler side. Powder coated. 1.9 in. dia. x .145 wall unplated tread rollers. Rollers are above frame on idler side.

CENTER DRIVE – Side mount high drive

ROLLER CHAIN – No. 40 chain




SPEED REDUCTION - Sealed worm gear C-face speed reducer

MOTOR – 1/2 HP –230/460V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient


CAPACITY – 850 lbs. total distributed live load based on a 90° curve. Not to exceed drive capacity in chart.

CHAIN DRIVEN LIVE ROLLER CURVE

(1.9 in. dia. x .145 wall rollers)

CONVEYING

SURFACE

BETWEEN

FRAME

OVERALL

FRAME

INSIDE

RADIUS

OUTSIDE

RADIUS

NUMBER OF ROLLERS WEIGHT (LBS.)

30° 45° 60° 90° 30° 45° 60° 90°

12 1/4" 15 1/2" 18 1/2"

35 1/4"

47 1/2" 6 8 11 16 196 238 277 374

14 1/4" 17 1/2" 20 1/2" 49 1/2" 6 8 11 16 202 247 288 392

16 1/4" 19 1/2" 22 1/2" 51 1/2" 6 8 11 16 210 258 301 412

18 1/4" 21 1/2" 24 1/2" 53 1/2" 6 8 11 16 217 268 314 432

20 1/4" 23 1/2" 26 1/2" 55 1/2" 6 8 11 16 224 278 332 451

22 1/4" 25 1/2" 28 1/2" 57 1/2" 6 8 11 16 231 288 345 471

24 1/4" 27 1/2" 30 1/2" 59 1/2" 6 8 11 16 238 298 360 491

28 1/4" 31 1/2" 34 1/2"

50 3/4"

79" 7 11 14 22 268 360 427 621

30 1/4" 33 1/2" 36 1/2" 81" 7 11 14 22 276 373 443 647

34 1/4" 37 1/2" 40 1/2" 85" 7 11 14 22 291 397 473 696

36 1/4" 39 1/2" 42 1/2" 87" 7 11 14 22 300 410 490 771

PLAN VIEW - 30, 45, 60, AND 90 CURVES

END VIEW SECTION VIEW X-X

OPTIONAL EQUIPMENT

FLOOR SUPPORTS – Floor supports are available in wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied above 36 in. top of roller.

CONVEYING SPEEDS - Other constant and variable speeds available from 15-60 FPM in any increment. Contact factory for speeds outside this range.

MOTORS – Inverter duty, premium energy efficient, single phase, brake motor, other characteristics. 3/4 HP maximum.

DRIVE VARIATIONS – Side mount low drives on 60° and 90° curves




47


CDC19T

The CDC19T chain driven live roller curves are compatible



from a straight section. Tapered rollers aid in the alignment

of packages

n 11 widths

n Tapered rollers


n Can be slave driven from CDS19


BED – 5 in. deep x 1 1/2 in. flange x 1/4 in. channel on drive side. 3 1/2 in. deep x 1 1/2 in. flange x 1/4 in. channel on idler side. Powder coated. 2 1/2 in. dia. tapered to 1 11/16 in. dia. x 14 ga. unplated tread rollers. Rollers are above frame on idler side.


ROLLER CHAIN – No. 40 chain





MOTOR – 1/2 HP –230/460V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient




(Tapered Rollers)

CONVEYING

SURFACE

BETWEEN

FRAME

OVERALL

FRAME

INSIDE

RADIUS

OUTSIDE

RADIUS

NUMBER OF ROLLERS WEIGHT (LBS.)

30° 45° 60° 90° 30° 45° 60° 90°

12 1/4" 15 1/2" 18 1/2"

35 1/4"

47 1/2" 6 8 11 16 201 245 287 384

14 1/4" 17 1/2" 20 1/2" 49 1/2" 6 8 11 16 204 249 291 397

16 1/4" 19 1/2" 22 1/2" 51 1/2" 6 8 11 16 212 261 305 418

18 1/4" 21 1/2" 24 1/2" 53 1/2" 6 8 11 16 219 271 318 438

20 1/4" 23 1/2" 26 1/2" 55 1/2" 6 8 11 16 226 281 336 457

22 1/4" 25 1/2" 28 1/2" 57 1/2" 6 8 11 16 234 292 350 479

24 1/4" 27 1/2" 30 1/2" 59 1/2" 6 8 11 16 242 303 367 501

28 1/4" 31 1/2" 34 1/2"

50 3/4"

79" 7 11 14 22 272 367 435 634

30 1/4" 33 1/2" 36 1/2" 81" 7 11 14 22 281 381 453 662

34 1/4" 37 1/2" 40 1/2" 85" 7 11 14 22 296 405 483 711

36 1/4" 39 1/2" 42 1/2" 87" 7 11 14 22 306 420 503 794

PLAN VIEW - 30, 45, 60 and 90 CURVES

END VIEW SECTION VIEW A-A

OPTIONAL EQUIPMENT

FLOOR SUPPORTS – Floor supports are available in wide range of adjustments. Specify top of roller elevations. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied above 36 in. top of roller.







48


CDS25

The CDS25 and CDS26 chain driven live roller is ideal for

carrying heavier loads such as loaded pallets and drums.

Roll-to-roll chain driven rollers also make it ideal for oily

conditions.


n 15 widths

n Reversible


BED – 6 in. x 8.2 lb. structural steel channel frame on drive side. 4 in. x 5.4 lb. structural steel channel frame on idler side. Powder coated. 2 1/2 in. dia. x 11 ga. unplated tread rollers spaced on 4 in., 5 in., 6 in. or 7 1/2 in. centers. Rollers are above the frame on idler side.


ROLLER-TO-ROLLER CHAIN – See chart





MOTOR – 1 HP – 230/460V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient


FRAME CAPACITY – Maximum load per linear foot of conveyor is 300 lbs. with supports on 10 ft. centers, 1000 lbs with supports on 5 ft. centers. Not to exceed drive capacity in chart.




CONVEYING SURFACE WIDTH (CSW)

15 3/4" 17 3/4" 19 3/4" 21 3/4" 23 3/4" 27 3/4" 29 3/4" 33 3/4" 35 3/4" 39 3/4" 43 3/4" 47 3/4" 51 3/4" 57 3/4" 63 3/4"

BETWEEN FRAME WIDTH

19 3/4" 21 3/4" 23 3/4" 25 3/4" 27 3/4" 31 3/4" 33 3/4 37 3/4" 39 3/4" 43 3/4" 47 3/4" 51 3/4" 55 3/4" 61 3/4" 67 3/4"

CHAINOVERALL WIDTH

23 1/4" 25 1/4" 27 1/4" 29 1/4" 31 1/4" 35 1/4" 37 1/4" 41 1/4" 43 1/4" 47 1/4" 51 1/4" 55 1/4" 59 1/4" 65 1/4" 71 1/4"

4" CENTERS - 10' LENGTH* NO. 40

CHAIN

752 790 831 869 907 986 1024 1104 1142 1221 1297 1409 1488 1608 1729

PER FOOT 64 67 71 75 79 86 90 96 100 108 115 123 130 141 152

5" CENTERS - 10' LENGTH NO. 50

CHAIN

695 726 759 790 821 885 916 980 1011 1072 1137 1234 1298 1397 1495

PER FOOT 57.6 60.6 63.8 66.8 69.8 76 79 85.2 88.2 94.2 100.2 108.2 114.2 123.6 133

6" CENTERS - 10' LENGTH

NO. 60

CHAIN

673 699 725 753 779 831 859 911 939 991 1045 1131 1188 1271 1353

PER FOOT 54 56 59 61 64 69 71 76 79 84 89 94 98 106 113

7 1/2" CENTERS - 10' LENGTH 610 631 652 675 696 739 762 804 827 869 914 990 1036 1105 1173

PER FOOT 49 51.2 53.2 55.4 57.4 61.4 63.6 67.6 69.8 74 78 83.8 88.2 94.6 100.8



OVERALL LENGTH

FPM HP 25' 50' 75'

15

115 3/4" - 29 3/4" 8000† 12000* 11500*

33 3/4" - 63 3/4" 8000† 11000* 9750*

215 3/4" - 29 3/4" 8000† 12000* 11500*

33 3/4" - 63 3/4" 8000† 11000* 9750*

30

115 3/4" - 29 3/4" 8000† 12000* 11500*

33 3/4" - 63 3/4" 8000† 11000* 9750*

215 3/4" - 29 3/4" 8000† 12000* 11500*

33 3/4" - 63 3/4" 8000† 11000* 9750*

45

115 3/4" - 29 3/4" 7500 7000 6250

33 3/4" - 63 3/4" 7000 6000 4750

215 3/4" - 29 3/4" 8000† 10500* 9750*

33 3/4" - 63 3/4" 8000† 9250* 8250*

Based on 5 in. roller centers, no. 50 chain and supports on 10 ft. centers

* Chain is limiting factor

† Frame is limiting factor

SECTION VIEW A-A

49


3 IN. ROLLER CENTERS

SECTION VIEW X-X (ROLL HIGH/LOW)

3 3/4 IN. ROLLER CENTERS

OPTIONAL EQUIPMENT

FLOOR SUPPORTS – 4 in. x 5.4 lb. structural channel floor supports are available in a wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied above 36 in. top of roller. Floor supports are also available with jack-bolt adjustment.




ROLLERS – 2 9/16 in. dia. x .180 wall unplated rollers (Model CDS26)

ROLLERS SET LOW – 6 in. x 8.2 lb. structural steel channel frame on drive side and idler side

OTHER ROLLER CENTERS 3 in. roller centers powered both sides • 6 in. x 8.2 lb. structural steel channel frame both side (rollers set low) • BF = Conveying surface width + 8 in. • Overall width = Conveying surface width + 12 in. 3 3/4 in. roller centers • 6 in. x 8.2 lb. structural steel channel frame on drive side • 4 in. x 5.4 lb. structural steel channel frame on idler side • BF = Conveying surface width + 6 1/2 in. • Overall width = Conveying surface width + 10 1/8 in.


CHANNEL END STOP – 6 in. x 8.2 lb. structural channel end stop

CHAIN CROSS-OVER – Transfers power from one side to the other

TRANSFERS – Right angle chain transfers available


ROLLERS LOW BOTH SIDES OPTION

6"

12"

CONVEYING

SURFACE

BETWEEN FRAME

OVERALL WIDTH 2-3/4"

1-7/8"

6"

50


CDC25

The CDC25 chain driven live roller curves are compatible



from a straight section.

n 16 widths

n Straight rollers

n Roller-to-roll chain drive

n Can be slaved from CDS25


BED – 6 in. x 8.2 lb. structural steel channel on drive side. 4 in. x 5.4 lb. structural steel channel on idler side. Powder coated. 2 1/2 in. dia. x 11 ga. unplated tread rollers. Rollers are above frame on idler side.












CONVEYINGSURFACE

BETWEENFRAME

OVERALLWIDTH

INSIDE RADIUS OUTSIDE RADIUS NUMBER OF ROLLERS WEIGHTS (LBS.)

30° 45° 60° 90° 30° 45° 60° 90° 30° 45° 60° 90° 30° 45° 60° 90°

15 3/4" 19 3/4" 23 1/4" 58 3/4" 46 1/8" 58 7/8" 52 1/2"

74 1/2" 61 7/8" 74 5/8" 68 1/4" 8 11 15 22

335 405 518 701

17 3/4" 21 3/4" 25 1/4" 56 3/4" 44 1/8" 56 7/8" 50 1/2" 346 418 536 728

19 3/4" 23 3/4" 27 1/4" 54 3/4" 42 1/8" 54 7/8" 48 1/2" 356 432 555 755

21 3/4" 25 3/4" 29 1/4" 52 3/4" 40 1/8" 52 7/8" 46 1/2" 367 446 575 784

23 3/4" 27 3/4" 31 1/4" 50 3/4" 38 1/8" 50 7/8" 44 1/2" 377 459 594 811

27 3/4" 31 3/4" 35 1/4" 79" 71 1/2" 67 3/4" 64"

106 3/4" 99 1/4" 95 1/2" 91 3/4"

10 14 18 26

479 641 755 1063

29 3/4" 33 3/4 37 1/4" 77" 69 1/2" 65 3/4" 62" 492 659 778 1096

33 3/4" 37 3/4" 41 1/4" 73" 65 1/2" 61 3/4" 58" 517 694 823 1160

35 3/4" 39 3/4" 43 1/4" 71" 63 1/2" 59 3/4" 56" 531 713 847 1195

39 3/4" 43 3/4" 47 1/4" 67" 59 1/2" 55 3/4" 52" 556 748 893 1260

43 3/4" 47 3/4" 51 1/4" 63" 55 1/2" 51 3/4" 48" 582 785 940 1327

47 3/4" 51 3/4" 55 1/4" 59" 51 1/2" 47 3/4" 44" 624 845 1019 1433

49 3/4" 53 3/4" 57 1/4" 67" 59 1/2" 55 3/4" 52"

116 3/4" 109 1/4" 105 1/2" 101 3/4"

673 889 1068 1516

51 3/4" 55 3/4" 59 1/4" 65" 57 1/2" 53 3/4" 50" 687 907 1092 1550

53 3/4" 57 3/4" 61 1/4" 63" 55 1/2" 51 3/4" 48" 701 926 1116 1583

55 3/4" 59 3/4" 63 1/4" 61" 53 1/2" 49 3/4" 46" 716 946 1142 1620

PLAN VIEW - 30º, 45º, 60º, AND 90º CURVES

51


OPTIONAL EQUIPMENT

FLOOR SUPPORTS – 4 in. x 5.4 lb. structural channel floor supports are available in a wide range of adjustments. Specify top of roller elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces recommended above 36 in. top of roller. Floor supports are also available with jack-bolt adjustment.




ROLLERS – 2 9/16 in. dia. x .180 wall unplated rollers (Model CDC26)




SECTION VIEW X-XEND/SIDE VIEW

52


CDC25T

The CDC25T chain driven live roller curves are compatible



for a straight section. Tapered rollers aid in the orientation

of packages.

n 14 widths

n Tapered rollers


n Can be slaved from CDS25



(Tapered Rollers)

CONVEYINGSURFACE

BETWEENFRAME

OVERALLWIDTH

INSIDE RADIUS

OUTSIDE RADIUS

NUMBER OF ROLLERS

WEIGHTS (LBS.)TAPERED ROLLER

30° 45° 60° 90° 30° 45° 60° 90°SMALL

DIA.LARGE

DIA.

15 3/4" 19 3/4" 23 1/4"

42 1/4"

58"

6 9 12 18

269 356 428 605

2 1/2"

3 1/2"17 3/4" 21 3/4" 25 1/4" 60" 284 378 452 649

19 3/4" 23 3/4" 27 1/4" 62" 299 401 472 698

21 3/4" 25 3/4" 29 1/4" 64" 315 424 498 744

23 3/4" 27 3/4" 31 1/4" 66" 338 457 518 808

4"27 3/4" 31 3/4" 35 1/4" 70" 370 506 568 903

29 3/4" 33 3/4 37 1/4" 72" 386 529 588 949

33 3/4" 37 3/4" 41 1/4" 76" 429 601 632 1,071

4 1/2"35 3/4" 39 3/4" 43 1/4" 82" 446 628 658 1,122

39 3/4" 43 3/4" 47 1/4" 86" 479 678 703 1,218

43 3/4" 47 3/4" 51 1/4" 90" 527 750 748 1,357

5"47 3/4" 51 3/4" 55 1/4" 94" 578 827 817 1,511

51 3/4" 55 3/4" 59 1/4" 100" 614 1080 889 1,619

57 3/4" 61 3/4" 65 1/4" 106" 669 966 965 1,779

PLAN VIEW - 90º, 60º, 45º, AND 30º CURVES

SECTION VIEW X-XEND/SIDE VIEW

OPTIONAL EQUIPMENT

BED – 6" x 8.2# structural steel channel frame on drive side. 4" x 5.4# structural steel channel frame on idler side. Powder coated. Unplated tapered rollers. See chart for taper details. Rollers are above the frame on idler side.




CHAIN GUARD – Formed steel upper and lower chain guard mounted to drive side channel frame to totally enclose drive chains.


SPEED REDUCTION - Sealed worm gear C-face speed reducer

MOTOR – 1 HP – 230/460V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient.







ROLLERS SET LOW – 6 in. x 8.2 lb. structural steel channel frame on drive side and idler side.

OTHER ACCESSORIES – Poly-tier supports, ceiling hangers.


CONVEYING SURFACE

OVERALL FRAME

BETWEEN FRAME

6"

5-3/8"

8-3/8"

1-3/8"

1/4"

4"

TAPERED ROLLER

LOWER CHAIN

GUARD

UPPER CHAIN GUARD

DRIVE GUARD

END/SIDE VIEW

OPTIONAL

SUPPORT

SHOWN

53


CDS35

The CDS35 chain driven live roller is ideal for heavier

applications. Its rugged design will provide service under

demanding manufacturing operations.



19 3/4" 21 3/4" 23 3/4" 27 3/4" 29 3/4" 33 3/4" 35 3/4" 41 3/4" 47 3/4" 53 3/4" 55 3/4" 63 3/4"

BETWEEN FRAME WIDTH

23 3/4" 25 3/4" 27 3/4" 31 3/4" 33 3/4" 37 3/4" 39 3/4 45 3/4" 51 3/4" 57 3/4" 59 3/4" 67 3/4"

CHAIN

SIZE

OVERALL WIDTH

27 5/8" 29 5/8" 31 5/8" 35 5/8" 37 5/8" 41 5/8" 43 5/8" 49 5/8" 55 5/8" 61 5/8" 63 5/8" 71 5/8"

6" CENTERS 5' LENGTH

NO. 60

CHAIN

775 813 852 928 967 1,042 1,080 1,195 1,326 1,442 1,481 1,636

PER FOOT 146 154 163 179 188 206 214 240 273 300 308 343

12" CENTERS 5' LENGTH 532 553 574 615 636 676 697 759 836 900 921 1,005

PER FOOT 98 102 107 117 122 133 137 152 175 191 196 218

n11 widths


n Reversible


BED – 7 in. x 9.8 lb. structural steel channel on drive side. 5 in. x 6.7 lb. structural steel channel on idler side. Powder coated. 3 1/2 in. dia. x .300 wall unplated tread rollers spaced on 6 in. or 12 in. centers. Rollers are above frame on idler side.









FRAME CAPACITY – Maximum load per linear foot of conveyor is 2000 lbs. with supports on with supports on 5 ft. centers. Not to exceed drive capacity in chart.


CONVEYING

SURFACE WIDTH

LENGTH

FPM HP 25' 50' 75'

15

215 3/4" - 29 3/4" 17,000* 15,000* 13,000*

33 3/4" - 63 3/4" 15,500* 12,250* 8,750*

315 3/4" - 29 3/4" 17,000* 15,000* 13,000*

33 3/4" - 63 3/4" 15,500* 12,250* 8,750*

35

215 3/4" - 29 3/4" 17,000* 15,000* 13,000*

33 3/4" - 63 3/4" 15,500* 12,250* 8,750*

315 3/4" - 29 3/4" 17,000* 15,000* 13,000*

33 3/4" - 63 3/4" 15,500* 12,250* 8,750*

45

215 3/4" - 29 3/4" 14,500* 12,500* 10,500*

33 3/4" - 63 3/4" 13,250* 9,750* 6,250*

315 3/4" - 29 3/4" 14,500* 12,500* 10,500*

33 3/4" - 63 3/4" 13,250* 9,750* 6,250*

Based on 6 in. roller centers, no. 60 chain and supports on 5 ft. *Chain is limiting factor


(3 1/2 in. dia. x .300 wall rollers)

FULL LENGTH CONVEYOR

14-1/2"

X

X

54


OPTIONAL EQUIPMENT



MOTORS – Inverter duty, premium energy efficient, other characteristics. 3 HP maximum.



ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible starters and push button stations, AC variable frequency drive

ROLLERS LOW BOTH SIDES OPTIONSECTION VIEW X-X (ROLLERS HIGH/LOW)

Documents

LIVE ROLLER CONVEYOR