Matrix BGA Socket - te.com · HXC-BGA Matrix BGA Socket Assembly Instructions Matrix BGA Sockets 0,80mm, 1,00mm, 1,27mm Pitch MPI-31758-01 Rev. 2. Tyco Electronics This document contains

Tyco Electronics

This document contains information which isthe exclusive property of Tyco ElectronicsDistribution, Reproduction or use by othersis not permitted without the expressed written consent of Tyco Electronics.

HXC-BGA Matrix BGA SocketAssembly Instructions

Matrix BGA Sockets0,80mm, 1,00mm, 1,27mm

Pitch

MPI-31758-01 Rev. 2

Tyco Electronics



1

2

43

56

7

1. 3mm Hex Wrench (Not Supplied.)2. Spring Plate Assembly. (Hardware Kit Item)3. Top Support Plate. (Hardware Kit Item)4. BGA Package (Not Supplied.)5. Matrix MPI BGA Socket Assembly. (Purchased Separately)6. Printed Circuit Board (Not Supplied.)7. Bolster Plate Assembly with Insulator. (Hardware Kit Item)

2 MPI-31758-01 Rev. 2

Tyco Electronics



1.) Place Bolster Plate Assembly with Insulator on a clean dry flat surface.

2.) Next place the Printed Circuit Board on the Bolster Plate Assembly, with the socketpads facing up, carefully aligning the four (4) holes in the board with the four postslocated on the Plate.

3 MPI-31758-01 Rev. 2

Tyco Electronics



3.) Carefully holding the socket by the edges only. (Care must be taken not to touch the MPIContacts). Place the socket on the PCB, aligning the posts on the socket to the holes in the PCB. Pushing down gently on the corners of the Location frame to seat the socket.

Press HerePress Here

4.) Holding the BGA package by its edges. Place the package in the socket. The corner frameshelp align the package to the holes in the socket. (Do not Push down on the socket as this willCompress the MPI contacts).

4 MPI-31758-01 Rev. 2

Tyco Electronics



5.) Align the four (4) holes in the plate to the four (4) posts and place the Top Support plateon top of the BGA Package.

PlaceSlide

6.) Place the Spring Plate Assembly on the post, by first insert the post thru the larger hole and then sliding the plate to capture the spring under the heads of the post.

5 MPI-31758-01 Rev. 2

Tyco Electronics



7.) Using your thumb and forefinger, slowly turn the hex screw in a clockwise direction, until all the variances has been removed from the assembly. The spring plate should nothave a deflection, but should be in contact with the head of the corner posts.

After

corner post head

Before

variance

6 MPI-31758-01 Rev. 2

Tyco Electronics



Start(1 Full Turn)

¼ Turn

½ Turn

¾ Turn9.) Turn the Hex Wrench the correct number of turns as prescribed in the table on the following Pages.(No. of Turns Vary according to Socket Size, pitch, and hardware kit.)

8.) Now remove the Hex wrench and Place it as shown in the above graphic.

Start(1 Full Turn)

¼ Turn

½ Turn

¾ Turn9.) Turn the Hex Wrench the correct number of turns as prescribed in the table on the following Pages.(No. of Turns Vary according to Socket Size, pitch, and hardware kit.)

8.) Now remove the Hex wrench and Place it as shown in the above graphic.

7 MPI-31758-01 Rev. 2

Tyco Electronics


HXC-BGA Matrix BGA SocketHardware Table 0,80 mm Sockets

* 0,80mm BGA Socket

31-1640302-1576

31-1640302-2625

2-1/21-1640302-0529

2-1/21640302-9484

2-1/21640302-8441

31640302-7400

31640302-6361

31640302-5324

2-1/21640302-4289

2-1/21640302-3256

31602302-2225

31640302-1196

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

* Be sure to verify the number of contacts and the Hardware Kit Part Number. Using the Wrong Hardware Kit could damage the MPI Contacts.

8 MPI-31758-01 Rev. 2

Tyco Electronics


HXC-BGA Matrix BGA SocketHardware Table 1,00 mm Sockets

* 1mm Small BGA Socket

* 1mm Medium BGA Socket

2-1/21640261-8784

21640261-7676

2-1/21640261-2729

21640261-6625

21640261-2576

31640261-1529

2-1/21640261-5484

1-1/21640261-2441

1-1/21640261-4400

21640261-1361

1-1/21640261-3324

11640261-2289

1-1/21640261-1256

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

31-1640261-31089

1-1/21-1640261-21024

2-1/21-1640261-1961

2-1/21-1640261-0900

2-1/21640261-9841

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

31-1640261-11156

* 1mm Medium BGA Socket

2401

2-1/22-1640261-22304

2-1640261-3 2-1/2

* 1mm Large BGA Socket

21-1640261-81521

21-1640261-71444

21-1640261-61369

21-1640261-51296

21-1640261-41225

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

22-1640261-31936

22-1640261-21849

22-1640261-11764

22-1640261-01681

33-1640261-51600

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

32-1640261-02500

2-1/22-1640261-12209

2-1/22-1640261-02116

22-1640261-42025


9 MPI-31758-01 Rev. 2

Tyco Electronics


HXC-BGA Matrix BGA SocketHardware Table 1,27mm Sockets

* 1,27mm Small BGA Socket

* 1,27mm Medium BGA Socket

1-1/21640261-2441

1-1/21640261-4400

21640261-1361

1-1/21640261-3324

11640261-2289

1-1/21640261-1256

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

2-1/22-1640261-7625

22-1640261-6576

31640261-9529

22-1640261-5484

2-1/21-1640261-1441

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

33-1640261-3676

* 1,27mm Medium BGA Socket

1600

1-1/22-1640261-41521

3-1640261-5 3

* 1,27mm Large BGA Socket

2-1/21-1640261-0900

2-1/21640261-9841

2-1/22-1640261-8784

21-1640261-3729

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

2-1/23-1640261-11225

2-1/21-1640261-91156

1-1/23-1640261-01089

33-1640261-21024

23-1640261-4961

NumberOf

Turns

HardwareKit

Part Number

NumberOf

Contacts

1-1/22-1640261-31444

1-1/22-1640261-21369

2-1/22-1640261-91296


10 MPI-31758-01 Rev. 2

Tyco Electronics


HXC-BGA Matrix BGA SocketAssembly Instructions, Revision History

1. Preliminary Release 03/26/03

2. Preliminary Change 10/01/04

MPI-31758-01 Rev. 2

Documents

Matrix BGA Socket - te.com · HXC-BGA Matrix BGA Socket Assembly Instructions Matrix BGA Sockets 0,80mm, 1,00mm, 1,27mm Pitch MPI-31758-01 Rev. 2. Tyco Electronics This document contains