2
Tel: +1.418.561.4512, Fax: +1.418.836.4575, [email protected] www.helitowcart.com 877A Alphonse-Desrochers, Saint-Nicolas, Levis, Quebec, Canada, G7A 5K6 BY VANAIR Introduction: The Heli-Carrier is a device that kneels down to slide under the helicopter belly up to the attachment position. In order to easily verify compatibility when the unit is in a kneeling position, we have indicated within this instruction the applicable resulting dimensions. In order to easily verify compatibility of this helicopter carrier, we recommend using a large cardboard and cut it to match the overall dimensions of a specific rectangle. Then simply slide this rectangle cardboard under the belly, from helicopter nose to one foot (30cm) aft of rear attachment pins usually used for installation of this helicopter’s wheels. Kneeled position Open space on top Wheel Pins attachment position Measurement Tool V1000 Heli-Carriers Carrier_V1000_MEASURE_TOOL_(2012_06_22) p.1/2

Measurement Tool V1000 Heli-Carriers BY VANAIR · V1000 Heli-Carriers Carrier_V1000_MEASURE_TOOL_ ... Carrier_V1000_MEASURE_TOOL_ ... Carrier_V1000_MEASURE_TOOL__2012_06_22_.doc

  • Upload
    buikhue

  • View
    244

  • Download
    4

Embed Size (px)

Citation preview

Tel: +1.418.561.4512, Fax: +1.418.836.4575, [email protected] www.helitowcart.com 877A Alphonse-Desrochers, Saint-Nicolas, Levis, Quebec, Canada, G7A 5K6

BY VANAIR

Introduction: The Heli-Carrier is a device that kneels down to slide under the helicopter belly up to the attachment position. In order to easily verify compatibility when the unit is in a kneeling position, we have indicated within this instruction the applicable resulting dimensions. In order to easily verify compatibility of this helicopter carrier, we recommend using a large cardboard and cut it to match the overall dimensions of a specific rectangle. Then simply slide this rectangle cardboard under the belly, from helicopter nose to one foot (30cm) aft of rear attachment pins usually used for installation of this helicopter’s wheels.

Kneeled position

Open space on top

Wheel Pins attachment position

Measurement Tool

V1000 Heli-Carriers

Carrier_V1000_MEASURE_TOOL_(2012_06_22) p.1/2

Tel: +1.418.561.4512, Fax: +1.418.836.4575, [email protected] www.helitowcart.com 877A Alphonse-Desrochers, Saint-Nicolas, Levis, Quebec, Canada, G7A 5K6

BY VANAIR

Figure 1 :

Figure 2 :

A

B

D

C

Helicopter Center

Overall dimension Top opening

Low Central Bar Rear Support Wheels

Carrier_V1000_MEASURE_TOOL_(2012_06_22) p.2/2

The above typical sketch demonstrates a cardboard cut to the Heli-Carrier’s specific rectangle model. The blank smaller rectangle on top of the base one demonstrates the open space available for antennas and accessories. See dimension tables below as well as Figure 1.

Overall Size of Carrier

(i.e. Large Cardboard Rectangle Size)

V1020 V1022 V1030 & V1032 V1040

A Width 58’’ (147 cm) 56’’ (143 cm) 59’’ (150 cm) 67’’ (170 cm) C 12.5’’ (32 cm) 12’’ (30,5 cm) 12’’(30,5 cm) 12’’(30,5 cm)

Length 172" (437 cm) 172" (437 cm) 202"(513 cm) / 212"(539 cm) 220"(559 cm)

Open Space on top of kneeled Carrier (i.e. Smaller Rectangle Size cut out of large rectangle at center top) :

V1020 V1022 V1030 & V1032 V1040

B 34’’ (86,5 cm) 26’’(66 cm) 26’’(66 cm) 34’’(86,5 cm) D 3’’ (8 cm) 4’’ (10,5 cm) 4’’ (10,5 cm) 4’’ (10,5cm)