MERCEDES AMG PETRONAS F1 TEAM -F1 W06 … · MERCEDES AMG PETRONAS F1 TEAM -F1 W06 AUSTRALIAN GP 2015 1:18 ScalePaper Craft* Assembly Instructions Instructions for car models #6 &

Look carefully at the photos of the completed parts and at the assembly diagrams, and glue the parts together in order of the numbers in the blue boxes.

2. Fold parts along the mountain fold lines (folds that make an A-shape) and valley folds (folds that make a V-shape).

1

Cutting line Mountain fold Glue tab Cut off (waste area)MERCEDES AMG PETRONAS F1 TEAM -F1 W06 AUSTRALIAN GP 2015

1:18 Scale Paper Craft* Assembly Instructions Instructions for car models #6 & #44 Fitting guideline Valley fold Glue on back Incision

Parts List Sheet 1The L and R that follow the part numbers stand for the left and ride sides as seen from the driver's seat.

Tool and materials you'll need● Scissors ● Hobby knife, such as an X-Acto knife ● Ruler ● Tweezers ● Toothpick ● Cutting mat● Glue (synthetic rubber adhesive or wood glue)● Scoring tool (a dull knife or empty ballpoint pen works well)

Nose Cone (top) a2

Nose Cone (side) a1R

Cut until reaching the red dots.

● Rod for curving the paper (a knitting needle or pencil works well)● Acrylic paint, sign paint, or markers for edging

R

a10R

Front Wing L

a10L

Front Wing (center)

a1L Nose Cone (side)

Nose Cone (bottom)a3L

Instructions

1.

a9R

a8R

a9L

a8L

a28 Nose Cone (bottom)

a3R

a4

Nose Cone (bottom) Cut out the parts along the solid black cut out lines.Check the cutting lines, fold lines, and so forth on the parts lists.TIP: For a more attractive finished model, color the white edges of the cut-out parts with the appropriate color of paint or marker before assembling the parts.

For crisp folds, lightly score the lines with a scoring tool first. Score from the back side of the paper to prevent nicking or scratching the printed surface.TIP: Sharply fold along the lines to form a crease.

3. To make curves, drag the paper over the edge of a ruler. Alternatively, rub a rod over the part you want to curve as shown in the illustration below.Curves are indicated by three parallel green lines.

4. Before applying glue to parts, examine the assembly diagrams and photos of completed parts, and dry-fit the parts to see how well they fit before gluing them together. Also check that the parts have the proper curves.

a6

a5

Cut out the pieces along the outside lines. Fold the paper along the mountain fold line so that the parts match back to back, then glue them together. Cut away the areas with the scissor marks.

Skid Block Undertray (bottom center)

Making Curves Rod

Place the part in the palm of one hand and, using a rod, rub the part you want to curl.

b1

*Paper Craft Design by Hitoshi Shinozaki; strictly not for commercial use

b3R b3L

Sheet 1/7

*As a rule, the parts are assembled in order from part No. 1 and then 2, 3, 4 and so on.Gray in the drawings is used to indicate the back side of the paper. Pink indicates where to apply glue.The L and R that follows the part numbers stand for the left and right sides as seen from the driver's seat.


b2 a12L a18L a23L a16L Front Wing-L

a7L a17L a19L a24L a15L a25L

a11L a13L a21L a22L a26L a27L a14L a20L

a23R a18R a12R Front Wing-R a16R

a24R a19R a17R a7R a25R a15R a26R a22R a21R a13R a11R a27R

a20R a14R

5. Use a toothpick or piece of scrap paper to spread a thin, even coat of glue.

MERCEDES AMG PETRONAS F1 TEAM -F1 W06 AUSTRALIAN GP 2015 1:18 Scale Paper Craft* Parts List Sheet 2 & 3

Undertray (bottom) Undertray (top)

b5 b6

b5 b6

b16L

b15L

Undertray front (top) b13L

b14L

Diffuser-L Lb9L

Diffuser (top)

b4L Diffuser side (inner)

Diffuser side (outer)

b4R

Undertray front (bottom) Undertray top (out) b10L b11L b12L

b7L b7R

Tail-L Tail center Tail-R

Diffuser-R Undertray top (in) Undertray front (top) R b9R b13R b16R

b12R b11R b10R b14R

Undertray top (out) Undertray front (bottom) b15R

b8

b19L b18 b19R

Color the back side completely black before cutting out.

b17


Sheet 2/7



Undertray top (in)

Headrest

c1

Head protection (side)

c3R

c3L

Induction pod (low) Induction pod (cover 1)

Induction pod (inner)

c5

Head protection

c6 c7

c4

Exhaust cover

Main body

c10

c11

Intake cover 2

c8

c12

Monocoque (side)

Cut until reaching the red dots. c14R

Cockpit (top)

Monocoque (side) c13

c14L

c9R

Head protection (side) c9L

Head protection (side)

Sheet 2/7

c2

Verti

cal fi

n

Cut o

ut the

piec

es al

ong t

he ou

tside

lines

. Fold

the p

aper

over

alon

g the

mo

untai

n fold

line s

o tha

t the p

arts

match

back

to ba

ck, th

en ap

ply gl

ue to

all

gray

area

s exc

ept fo

r the

gray

area

s of th

e pro

trudin

g par

ts, an

d glue

them

tog

ether

. Cut

away

the a

reas

with

the s

cisso

r mar

ks.

2

*Strictly not for commercial use

MERCEDES AMG PETRONAS F1 TEAM -F1 W06 AUSTRALIAN GP 2015 1:18 Scale Paper Craft*

3

Side pontoon (side)

e13L

Bottom

front

Cut u

ntil re

achin

g the

red d

ots.

c17L

c15L Side pontoon (side)

Side Pontoon (side) c17R

c15R

Body end parts(inner)

c18

Side pontoon (side)

c16L c19 Body end parts(outer)

Side pontoon (side) c16R d7


Monocoque (bottom)

Monocoque (bottom)

Front sus (top) c20 c21 Front sus (bottom) d8

Seat (side)

Seat( center) d2L

d10

d1

d2R

Seatbelt

d3

Steering wheel stay

d6

Seat (side) d11L

Cockpit d4

Body end parts (side rectifier)

d11R

Cut out the pieces along the outside lines. Fold the paper along the mountain fold line so that the parts match back to back, then glue them together. Cut away the areas with the scissor marks. Sheet 4/7

Cut u

ntil re

achin

g the

red d

ots.

Front

Front

d9

Bottom Seat front

d5

Rear brake (out) up

Rear Brake-R

R up

e10R

e11R

e9R e3R

e5R e4R

e7R

e2L

e10L

e11L e3L

e9L e4L

e5L e6L

e8L e7L

Rear brake-L

Rear brake (out) up

low

L

f1L

f8L f7L f5L

R

f1R

f5R f7R f8R

up

Rear sus bottom-R

Fron

t

Fron

t sus

tie ro

d

Fron

t sus

push

rod

Rear

sus b

ottom

-L

Rear brake duct

e1L e1R

up

e12L

e13L Rear brake/wheel hub

up

e14L

e19L

e13R

e19R Rear sus

Rear brake wheel hub (out 1)

up

e12R

up

e14R Cut out the pieces along the outside lines. Fold the paper over along the mountain fold line so that the parts match back to back, then apply glue to all gray areas except for the gray areas of the protruding parts, and glue them together. Cut away the areas with the scissor marks.

e15

Tail stay

e22 e16 up

e18

e23

Exhaust cover

Rear push rod

e21

Rear push rod

e20R e20L

Rear sus top

f6R

e24L e24R

Front brake-L Front brake-R

f9

f3L f3R f2 f4 f4 f2

f6L

f13 f14

f11 Front brake/wheel hub f11 Front brake/wheel hub

f12 f10 f10 f12

Nose join (upper)

Nose join (lower)

Front brake wheel hub (in)

Front brake wheel hub (out)

Front brake wheel hub (out)

Front brake wheel hub (in)

Color

the b

ack s

ide co

mplet

ely bl

ack b

efore

cuttin

g out.

Cut o

ut the

piec

es al

ong t

he ou

tside

lines

. Fold

the p

aper

alon

g the

mou

ntain

fold l

ine so

that

the pa

rts

match

back

to ba

ck, th

en gl

ue th

em to

gethe

r. Cu

t awa

y the

area

s with

the s

cisso

r mar

ks.

Rear Brake/wheel hub

Cut o

ut the

piec

es al

ong t

he ou

tside

lines

. Fold

the p

aper

alon

g the

mo

untai

n fold

line s

o tha

t the p

arts

match

back

to ba

ck, th

en gl

ue th

em

togeth

er. C

ut aw

ay th

e are

as w

ith th

e scis

sor m

arks

.




Exhaust end

Rear brake wheel hub (in)



e2R

e6R e8R

up

e17

up

Sheet 5/7

Parts List Sheet 4 & 5


Barge board 3

Rear

win

g 1

Barg

e bo

ard

1(up

) Ba

rge

boar

d 1(

up)

Rear

win

g 2

4

DRS (out) g7R g7R i1R i9R

i10R DRS (inner)

g6

g1 g2

g3R g3L i1L

Front wheel i2R

i2L i9L

Rear wheel

i10L Rear wing stay

g5

Barge board 1 (side)

Rear wing side (inner) i3 i3 i3 i3

Hub caps

h3L h3R

g4R g4L

Tire outer - L Tire inner - L Tire inner - L Tire outer - L

i4L i5L i5L i11L

h1L Rear wing side (outer)

Rear

h6L h2L h7L

On-board camera (top)

h27R On-board camera (side)

h29

Tire outer - R Tire inner - R Tire inner - R Tire outer - R

h1R

h6R

h27L

h26 h30

Intake (bottom) h25

i4R i5R

Front

i5R i11R

Rear

Steering wheel

h22

h23

h19L

h2R

h7R

Side mirror

h28

h19R

Side mirror - back canard

h20L

h20R

Wheel inner Wheel inner i6 i6

Wheel inner Wheel inner i6 i6

Wheel inner i7

Front tire tread i8

Front tire tread i8

Steering shaft

h24

h16L

h17L

h18L On-board camera (front) h18R h16R

h17R Wheel inner i7

h14L Turning vanes 1 h14R Turning vanes 2

Pilot tubes & antenna Wheel inner i7

Rear tire tread i12

h13 h12 h33 h34

Turning vanes 1 Stable stand

h32 h35 h31 Wheel inner i7

Rear tire tread i12

h15L h15R h11

h4L h5L h5R h4R

Cut out the pieces along the outside lines. Fold the paper over along the mountain fold line so that the parts match back to back, then apply glue to all gray areas except for the gray areas of the protruding parts, and glue them together. Cut away the areas with the scissor marks.

Cut o

ut the

piec

es al

ong t

he ou

tside

lines

. Fold

the p

aper

alon

g the

mou

ntain

fold l

ine so

that

the pa

rts

match

back

to ba

ck, th

en gl

ue th

em to

gethe

r. Cu

t tway

the a

reas

with

the s

cisso

r mar

ks.

Cut o

ut the

piec

es al

ong t

he ou

tside

lines

. Fold

the p

aper

alon

g the

mou

ntain

fold l

ine so

that

the pa

rts m

atch

back

to ba

ck, th

en gl

ue th

em to

gethe

r. Cu

t awa

y the

area

s with

the s

cisso

r mar

ks.

Cut out the pieces along the outside lines. Fold the paper over along the mountain fold line so that the parts match back to back, then apply glue to all gray areas except for the gray areas of the protruding parts, and glue them together. Cut away the areas with the scissor marks.

h33

Barge board 3(stay) h9R

h8R Barge board 2

h10R

Barge board 3 (stay) h9L

h8L barge board 2

h10L Barge board 3

Sheet 6/7

MERCEDES AMG PETRONAS F1 TEAM -F1 W06 AUSTRALIAN GP 2015 1:18 Scale Paper Craft* Parts List Sheet 6 & 7

Sheet 7/7


MERCEDES AMG PETRONAS F1 TEAM -F1 W06 AUSTRALIAN GP 2015 1:18 Scale Paper Craft* Assembly Instructions

*Strictly not for commercial use.

*For best results make crisp folds.

Glue first.

Glue edges only.

Pre-cut slots before assembling.

Front wing (front view / actual size) Shape both sides so a9 and a10 curve progressively upwards.

[Parts required: a1 to a4]Assemble in order of the numbers in the blue boxes after curving appropriately.

Carefully study the actual size front view (left) and completed photos (bottom left) and shape each part to match, then align the guide lines and glue edges.

[Parts required: a5 to a28]All parts except a28 need to be folded and glued back to back before being cut out. Assemble in order of the numbers in the blue boxes after curving appropriately.

Guide lines for gluing

Shape to match the actual size front view above, then glue.

Completed front wing

Guide lines for gluing

Glue edges, both sides. Align same color triangles

and glue edges.

*Shape so front and sides are square.

*Diagram shows left side; assemble right in the same fashion.

Set v

ertic

ally

.

Glue

firs

t.

Align same color triangles and glue edges.*Diagram shows left side; assemble right in the same fashion.

Fold over from the front and glue down. *Diagram shows right side; assemble left in the same fashion.

Atta

ch s

o it

slig

htly

rai

ses

diag

onna

lly.

[Parts required: b1 to b19]

For best results make crisp folds.Assemble in order of the numbers in the blue boxes after curving appropriately.

Align both sides with these lines, then glue.

Apply glue to entire surface.

Raise rear edge by approx. 5 mm, both top and bottom.

Apply glue to entire surface.

Curve these sections on both sides before gluing.

Curve these sections on both sides before gluing.

For

both

sid

es, e

nsur

e th

ese

sect

ions

sta

y fla

t and

do

not

sag

dow

nwar

d.

Align both sides with these lines, then glue.

*Insert all tabs on both sides, then fold down and glue.

Completed undertray / diffuser

*Parts b9 to b17 need to be folded and glued back to back beforebeing cut out. Align same color triangles and glue edges. Assemble in order of the numbers in the blue boxes after curving each part to its guide line.

Color back side black and glue to edges of undertray.

Color back side black and glue edge.

Completed undertray rear top view



[Parts required: c1 to c19]Assemble in order of the numbers in the blue boxes after curving appropriately.

Insert tab, fold out, and glue.

Shape to match c6 before gluing.

Glue after curving appropriately.

Curve and glue into a rounded triangle shape.

InseInsert all tabs on both sides, then fold down and glue.


Pre-

cut s

lots

bef

ore

asse

mbl

ing.

Match to body lines.


Glue here first.

Align with this line.

Raise to form glue tabs.

Assemble radiator section first.

*Diagram shows left side; assemble right in same fashion.

Curve into shape and glue from the center first, then down each side.Glue little by little, in line with the guide lines.

Center


Align and glue completed section to body.

Completed main body

Insert tabs, fold out, and glue. Fold and glue this part back to back before cutting out.



[Parts required: c20 to c21 / d1 to d6]Assemble in order of the numbers in the blue boxes.

Fold and glue down inside.

Inse

rt o

nly.

Do

not g

lue.


Make crisp folds to both the upper and lower arms.

Curve to the shape of the seat.


Fold into a box shape as shown.

Completed main body underside



Completed cockpit

[Parts required: d7 to d11]Assemble in order of the numbers in the blue boxes.

Completed main body underside, base attached

Align with d10 and glue down little by little from front to back.

Fold and glue these parts back to back before cutting out.Curve sufficiently before attaching.



[Parts required: e1 to e14]

*All parts except e1 need to be folded and gluedback to back before being cut out.Align same color triangles and glue edges. Assemble in order of the numbers in the blue boxes after curving each part.

Cut out.Color back side black.

Align triangle marks and glue.

*Diagram shows right side;assemble left in same fashion.

Align shaft holes, then align same color triangles and glue.

Ensure shaft holes face right way, align same color triangles and glue.

Cut out shaft holes before gluing.

*Diagram shows right side; assemble left in same fashion.

Completed rear brake / wheel hub

[Parts required: e15 to e21] Assemble in order of the numbers in the blue boxes.

Curve into a wing shape.

Insert shaft, then fold up the small triangular tabs on both sides.These will form the rear brake stoppers. No need to glue the shaft in place.

Traingular tab

Traingular tab

Cut out shaft hole before any gluing.

Make all folds, then attach glue tabs as shown.

Color back side black.

Attach one side's lower arm to the shaft, insert opposite end into the body, and fix the gearbox in place.Next, insert the other lower arm's tab into the body and attach its opposite end to the shaft.

Lower arm

Lower arm

No need to glue either side.Fold and glue these parts back to back before cutting out, except for the glue tabs.

Fold and glue parts back to back before cutting out. The underside has the marks for gluing the push rods.

Ensure push rods are attached to their correct sides.

Fold and glue these parts back to back before cutting out, except for the glue tabs.

Bend slightly so they go in smoothly.

Glue here only. Other parts should just be inserted in their slots.



[Parts required: e22 to e24] Assemble in order of the numbers in the blue boxes.

For both sides, align same color triangles and glue.

Completed rear section

*Color back of both parts blackbefore shaping.

Insert and glue so triangles are aligned.

Insert shaft into wheel hub.Glue edge of upper arm to top of brake duct.Fold up both glue tabs at the end of the shaft and glue.

*Assemble two of these.

Light colored area at the bottom.Glue so the join of f11 also at the bottom.

*Join


Colo

r ba

ck s

ide

blac

k.

*All parts except f2 to f4 need to be foldedand glued back to back before being cut out. Assemble in order of the numbers in the blue boxes after curving appropriately.

*Align all same color trianglesappropriately and glue.


Attach diagonally upwards at a 60 degree angle, as per the photo above.

*Color back of part black.

[Parts required: f1 to f12]Assemble in order of the numbers in the blue boxes.

Guide up through the center of the upper arm and attach to the body slots.No gluing required.

Insert between upper and lower arms. No gluing required.

Completed front suspension



Completed front brake duct / push rod

[Parts required: f13 and f14] Assemble in order of the numbers in the blue boxes.

Just insert arms both sides.No gluing required.

Nose cone assembled in

Align to guide lines on undertray and glue.

Nose cone assembled in

Fold and glue back to back before cutting out, except for the glue tabs.

[Parts required: g1 to g7] Assemble in order of the numbers in the blue boxes.

Insert stay (g5) up to its guide line in wing slot, then glue down DRS lever (g6).

Cut slot, curve, and glue just 1 to 2 mm of the edge.

Guide line

*Glue all tips.

Pre-cut 2 slots in (g1), then shape both wings to fit the banana shapes on the end plates.Glue just 1 to 2 mm of the wing edges, then double check their shapes before attaching the wings to the end plates.


For both sides, insert tabs, fold out, and glue.

Completed rear wing



[Parts required: h1 to h20] Assemble in order of the numbers in the blue boxes.

Curve into a wing shape and glue just the tips of the edges.



Assemble mirrors and curve their stays as per the photos below.

Completed side mirror

Attach parallel to the ground.


Fold and glue each part back to back before cutting out, then curve to match the diagram below, which is actual dimensions.Glue all edges.

For to , align same color triangles and glue edges. Same for the right side.

Fold and glue back to back before cutting out, apply curve, then align same color triangles and glue edges.

*Diagram shows left side; assemble right in same fashion.

Sandwich glue tab, and glue.

Black edge

Align same color triangles and glue

Fold and glue back to back before cutting out, then shape to match the actual dimensions in the diagram below. The guide lines on the back of the part show where to curve.

Barge board (actual dimensions)

Left: rear view Right: front view

Barge board (top view/actual dimensions)

Undertray

Back

Apply diluted wood glue to entire back surface and quickly form into a circular shape once paper softens. (This is the base the car rests on.)

Completed turning vanes, etc.

Glue edges.

All parts except h15 need to be folded and glued back to back before being cut out. Refer to the completed part photos, etc. to curve each part appropriately, and then glue.



[Parts required: h21 to h35] Assemble in order of the numbers in the blue boxes.

Curve into a wing shape and glue just the tips of the edges.

Glue at edges.

Assemble in same fashion as diagram to the left.

Fold and glue h22 and h23 back to back before cutting out. Align same color triangles and glue.

Apply diluted wood glue to entire back surface and quickly form into a circular shape once paper softens.

Fold into a trapezoidal box shape.

Completed stearing wheel#6 Nico rosberg

Pre-cut 2 slots, curve, then insert h33 and glue.Then, glue h32 by its edges only.

Front wing assembled in

[Parts required: i1 to i12] Assemble in order of the numbers in the blue boxes.

*Define top and bottom of the tires by aligning the joins as you glue.Sufficiently curve both the sides (i4, i5, i11) and the treads (i8, i12) before gluing.Numbering the back of each part with a pencil makes assmebly easier.

Glue tire sides into a ring shape, then add outward curvature once the glue has dried.

Front tire

Rear tireLeft Right

Join

Join

Join

Join

Left Right

Join

Join

Join

Join

Glue at edges.

Rear tire (left)

Front tire (left)

Position Pirelli logo at the top of each tire.

With all 4 tires attached, glue on front wing so that it is parallel to the ground when viewed from the side.



Documents

MERCEDES AMG PETRONAS F1 TEAM -F1 W06 … · MERCEDES AMG PETRONAS F1 TEAM -F1 W06 AUSTRALIAN GP 2015 1:18 ScalePaper Craft* Assembly Instructions Instructions for car models #6 &