Mercury Grand Marquis Owners Manual 1998

Embed Size (px)

DESCRIPTION

Mercury Grand Marquis Owners Manual 1998

Citation preview

  • Before driving

    Introduction 2

    Instrumentation 3

    Controls and features 23

    Seating and safety restraints 57

    Starting and driving

    Starting 77

    Driving 82

    Roadside emergencies 94

    Servicing

    Maintenance and care 107

    Capacities and specifications 142

    Reporting safety defects 148

    Index 149

    All rights reserved. Reproduction by any means, electronic or mechanicalincluding photocopying, recording or by any information storage and retrievalsystem or translation in whole or part is not permitted without writtenauthorization from Ford Motor Company.

    Copyright r 1997 Ford Motor Company

    Contents

    1

  • ICONSIndicates a warning. Read thefollowing section on Warnings for afull explanation.

    Indicates vehicle information relatedto recycling and otherenvironmental concerns will follow.

    Correct vehicle usage and theauthorized disposal of wastecleaning and lubrication materials are significant steps towardsprotecting the environment.

    WARNINGSWarnings provide information which may reduce the risk of personalinjury and prevent possible damage to others, your vehicle and itsequipment.

    BREAKING-IN YOUR VEHICLEThere are no particular breaking-in rules for your vehicle. During thefirst 1 600 km (1 000 miles) of driving, vary speeds frequently. This isnecessary to give the moving parts a chance to break in.

    If possible, you should avoid full use of the brakes for the first 1 600 km(1 000 miles).

    INFORMATION ABOUT THIS GUIDEThe information found in this guide was in effect at the time of printing.Ford may change the contents without notice and without incurringobligation.

    Introduction

    2

  • Instrumentation

    3

  • BAS

    SEEK

    TUNE

    VOL - PUSH ON

    HILO

    F

    SOFF

    E

    CHECKENGINE

    AIRSUSP

    ODOFF

    BRAKE

    TEMP OILVOLTS FUEL

    MPH km/h10

    20

    30

    4050

    60 7080

    90

    100

    110

    12020

    40

    60

    80100

    120

    140

    160

    180

    200

    HH

    LC

    FH

    L< FUEL FILL DOOR

    NORM A/CMAX A/C

    OUTSIDE TEMP

    1 2

    CD

    AMFM

    R.DEF.

    AUTOLAMP

    0FF

    PANELDIM

    PUSH INTERIOR

    P R N D 2 1

    OFF

    ON

    RSM

    SETACC

    COAST

    Driver side airbag

    (pg. 67)

    Instrumentcluster(pg. 22)

    Rear windowdefroster control

    (pg. 24)

    Tilt steeringwheel lever(pg. 35)

    Instrument paneldimmer switch

    (pg. 23)

    Headlamp control(pg. 23)

    Speed control*(pg. 36)

    Gearshift lever(pg. 87)

    Turn signal andwiper/washer

    control(pg. 34)

    *if equipped

    Instrumentation

    4

  • SVENT FLOOR FLR DEF DEF

    HI

    LO

    AUTOMATIC

    OFFF

    AUTO

    REWSIDE 1-2

    FFSCAN EJ

    TREB BAL FADE

    3 4 5 6

    fw DOLBY B NR

    FM1 ST CLK

    TAPEAMS

    H M

    Electronic soundsystem(pg. 33)

    Passenger side airbag

    (pg. 67)

    Climate controlsystems(pg. 25)

    Clock(pg. 33)

    Instrumentation

    5

  • WARNING LIGHTS AND CHIMES

    Standard instrument cluster

    Optional instrument cluster

    Low fuelIlluminates when the fuel level islow. The lamp will also illuminatewhen the ignition is turned to ONand the engine is off.

    Check engineYour vehicle is equipped with acomputer that monitors the enginesemission control system. Thissystem is commonly known as theOn Board Diagnostics System (OBD

    E

    LOWFUEL

    CHECKENGINE

    AIRSUSP

    ODOFF

    BRAKEAIRBAG

    TEMP OILVOLTS FUEL

    MPH km/h10

    20

    30

    4050

    60 7080

    90

    100

    110

    12020

    40

    60

    80100

    120

    140

    160

    180

    200

    HH

    LC

    FH

    L< FUEL FILL DOOR

    TRACCNTL

    0 0 0 0 0 0 0

    0000

    +

    F

    E

    /21

    NORM

    H

    C

    LTRGALTO

    EMPTY

    km/hMPH

    kmSCHECKENGINE

    AIRBAG

    SPEED CONTROL

    P R N D 2 1

    CHECK

    TRUNK AJAR LTR/100 km

    AIR SUSPENSIONOVERDRIVE OFF

    DOORAJAR

    LOWWASHERFLUID

    DIST TOEMPTY

    TRIPA

    AVGECON

    TRIPB

    INSTECON

    AVGSPEED

    kmMILES/GAL

    LOWFUEL

    CHECKENGINE

    Instrumentation

    6

  • II). This OBD II system protects the environment by ensuring that yourvehicle continues to meet government emission standards. The OBD IIsystem also assists the service technician in properly servicing yourvehicle.

    The Check Engine indicator light illuminates when the ignition is firstturned to the ON position to check the bulb. If it comes on after theengine is started, one of the engines emission control systems may bemalfunctioning. The light may illuminate without a driveability concernbeing noted. The vehicle will usually be drivable and will not requiretowing.

    What you should do if the check engine light illuminatesLight turns on solid:

    This means that the OBD II system has detected a malfunction.

    Temporary malfunctions may cause your Check Engine light toilluminate. Examples are:

    1. The vehicle has run out of fuel. (The engine may misfire or runpoorly.)

    2. Poor fuel quality or water in the fuel.

    3. The fuel cap may not have been properly installed and securelytightened.

    These temporary malfunctions can be corrected by filling the fuel tankwith good quality fuel and/or properly installing and securely tighteningthe gas cap. After three driving cycles without these or any othertemporary malfunctions present, the Check Engine light should turn off.(A driving cycle consists of a cold engine startup followed by mixedcity/highway driving.) No additional vehicle service is required.

    If the Check Engine light remains on, have your vehicle serviced at thefirst available opportunity.

    Light is blinking:

    Engine misfire is occurring which could damage your catalytic converter.You should drive in a moderate fashion (avoid heavy acceleration anddeceleration) and have your vehicle serviced at the first availableopportunity.

    Instrumentation

    7

  • Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior

    floor coverings or other vehicle components, possibly causing a fire.

    Air bag readinessMomentarily illuminates when theignition is turned ON. If the lightfails to illuminate, continues to flashor remains on, have the systemserviced immediately.

    Safety beltMomentarily illuminates when theignition is turned to the ON positionto remind you to fasten your safetybelts. For more information, refer tothe Seating and safety restraintschapter.

    Brake system warning (if equipped)Momentarily illuminates when theignition is turned to the ON positionand the engine is off. If brakewarning lamp does not illuminate atthis time, seek service immediately.Also illuminates when the parking brake is engaged. Illumination afterreleasing the parking brake indicates low brake fluid level and the brakesystem should be inspected immediately.

    Anti-lock brake system (ABS) (If equipped)Momentarily illuminates when theignition is turned on and the engineis off. If the light does not illuminatemomentarily at start up, remains onor continues to flash, the ABS needsto be serviced. With the ABS light on, the anti-lock brake system isdisabled and normal braking is still effective unless the brake warninglight also remains illuminated with parking brake released.

    AIRBAG

    !BRAKE

    ABS

    Instrumentation

    8

  • Turn signalIlluminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators stay on continuously orflash faster, check for a burned-outturn signal bulb. Refer to Exterior bulbs in the Maintenance and carechapter.

    High beamsIlluminates when the high beamheadlamps are turned on.

    Charging systemIlluminates when the ignition isturned to the ON position and theengine is off. The light alsoilluminates when the battery is notcharging properly, requiringelectrical system service.

    Engine oil pressure (if equipped)Illuminates when the oil pressurefalls below the normal range. Stopthe vehicle as soon as safelypossible and switch off the engineimmediately. Check the oil level andadd oil if needed. Refer to Engine oil in the Maintenance and Carechapter.

    This lamp also illuminates when the ignition is turned to ON and theengine is off.

    Instrumentation

    9

  • Engine coolant temperatureIlluminates when the engine coolanttemperature is high. Stop thevehicle as soon as safely possible,switch off the engine and let it cool.

    Never remove the coolantrecovery cap while the

    engine is running or hot.

    Refer to Engine coolant in the Maintenance and care chapter. If lightstays on or continues to turn on after the vehicle warms up, have yourvehicle serviced.

    This light also illuminates briefly when the ignition key is turned to ON.

    Air suspension (if equipped)This light tells you if the airsuspension needs repair or if the airsuspension switch is OFF. Forinformation on the air suspensionsystem, refer to the Drivingchapter.

    O/D offIlluminates when the transmissioncontrol switch has been pushed.When the light is on, thetransmission does not shift intooverdrive. If the light does not comeon when the transmission control switch is depressed or if the lightflashes when you are driving, have your vehicle serviced.

    AIRSUSP

    O/DOFF

    Instrumentation

    10

  • Traction ControlY active (if equipped)Flashes when the Traction Controlysystem begins applying andreleasing the brakes and adjustingthe engine characteristics to limit awheelspin condition. It will be lit fora minimum of four seconds or forthe duration of the TractionControly event.

    If the Traction Controly indicatorcomes on or stays lit, either:

    the Traction Controly system needs service, or the customer has disabled the system using the traction controlswitch.

    For more information, refer to the Driving chapter.

    Safety belt warning chimeChimes to remind you to fasten your safety belts.

    For information on the safety belt warning chime, refer to the Seatingand safety restraints chapter.

    Supplemental restraint system (SRS) warning chimeFor information on the SRS warning chime, refer to the Seating andsafety restraints chapter.

    Key-in-ignition warning chimeSounds when the key is left in the ignition in the OFF/LOCK or ACCposition and either front door is opened.

    Headlamps on warning chimeSounds when the headlamps or parking lamps are on, the ignition is off(and the key is not in the ignition) and either front door is opened.

    Turn signal chimeSounds when the turn signal lever has been activated to signal a turn.

    TRACCNTL

    Instrumentation

    11

  • GAUGES

    Standard instrument cluster gauges

    Optional instrument cluster gauges

    Fuel gaugeDisplays approximately how much fuel is in the fuel tank (when the keyis in the ON position). The fuel gauge may vary slightly when the vehicleis in motion. The ignition should be in the OFF position while the vehicleis being refueled. When the gauge first indicates empty, there is a smallamount of reserve fuel in the tank. When refueling the vehicle fromempty indication, the amount of fuel that can be added will be less thanthe advertised capacity due to the reserve fuel.

    E

    LOWFUEL

    TRACCNTL

    CHECKENGINE

    AIRSUSP

    ODOFF

    BRAKEAIRBAG

    TEMP OILVOLTS FUEL

    MPH km/h10

    20

    30

    4050

    60 7080

    90

    100

    110

    12020

    40

    60

    80100

    120

    140

    160

    180

    200

    HH

    LC

    FH

    L< FUEL FILL DOOR

    0 0 0 0 0 0 0

    0000

    +

    F

    E

    /21

    NORM

    H

    C

    LTRGALTO

    EMPTY

    km/hMPH

    kmSCHECKENGINE

    AIRBAG

    SPEED CONTROL

    P R N D 2 1

    CHECK

    TRUNK AJAR LTR/100 km

    AIR SUSPENSIONOVERDRIVE OFF

    DOORAJAR

    LOWWASHERFLUID

    DIST TOEMPTY

    TRIPA

    AVGECON

    TRIPB

    INSTECON

    AVGSPEED

    kmMILES/GAL

    Instrumentation

    12

  • Standard instrument cluster

    Optional instrument cluster

    SpeedometerIndicates the current vehicle speed.

    Standard instrument cluster

    E

    FUELF

    F

    E

    /21

    MPH km/h10

    20

    30

    4050

    60 7080

    90

    100

    110

    12020

    40

    60

    80100

    120

    140

    160

    180

    200

    0 0 0 0 0 0 0

    0000

    Instrumentation

    13

  • Optional instrument cluster

    OdometerRegisters the total kilometers(miles) of the vehicle.

    Standard instrument cluster

    Optional instrument cluster

    Refer to Electronic Message Center for information on how to switchthe display from metric to English measurements.

    km/hMPH

    kmS

    MPH km/h10

    20

    30

    4050

    60 7080

    90

    100

    110

    12020

    40

    60

    80100

    120

    140

    160

    180

    200

    0 0 0 0 0 0 0

    0000

    km/hMPH

    kmS

    Instrumentation

    14

  • Trip odometerRegisters the kilometers (miles) ofindividual journeys. To reset,depress the control.

    Refer to electronic message center for Trip A and Trip B features on theoptional instrument cluster.

    Engine coolant temperature gaugeIndicates the temperature of the engine coolant. At normal operatingtemperature, the needle remains within the normal area (the areabetween the H and C). If it enters the red section, the engine isoverheating. Stop the vehicle as soon as safely possible, switch off theignition and let it cool. Refer to Engine coolant in the Maintenanceand care chapter.

    Never remove the coolant recovery cap while the engine isrunning or hot.

    Standard instrument cluster

    0 0 0 0

    20

    30

    40

    5060 70

    80

    90

    100

    110

    12010 20

    40

    60

    80

    100 120

    140

    160

    180

    MPH

    km/h

    0 00 000

    TEMPH

    C

    Instrumentation

    15

  • Optional instrument cluster

    This gauge indicates the temperature of the engine coolant, not thecoolant level. If the coolant is not at its proper level or mixture, thegauge indication will not be accurate.

    Battery voltage gauge (if equipped)This gauge shows the batteryvoltage when the ignition is in theON position. If the pointer movesand stays outside the normaloperating range (as indicated), havethe vehicles electrical systemchecked as soon as possible.

    Engine oil pressure gauge (if equipped)This shows the engine oil pressurein the system. Sufficient pressureexists as long as the needle remainsin the normal range (the areabetween the H and L).

    If the gauge indicates low pressure,stop the vehicle as soon as safelypossible and switch off the engineimmediately. Check the oil level.Add oil if needed (refer toChecking and adding engine oil in the Maintenance and care

    NORM

    H

    C

    VOLTSH

    L

    OILH

    L

    Instrumentation

    16

  • chapter). If the oil level is correct, have your vehicle checked at yourdealership or by a qualified technician.

    ELECTRONIC MESSAGE CENTERThe electronic message center onlyworks when the ignition is in theON position.

    The message center allows you to:

    see problems such as door ajar,air suspension, trunk ajar, washerfluid low

    see how many kilometers/milesyou can drive before running outof fuel

    see when overdrive has been deactivated monitor the average fuel economy monitor the instantaneous fuel economy check the distance traveled during a trip on either Trip A or Trip B monitor the average speedSelectable featuresResetPress this control to reset theselected message center function tozero. The only functions which canbe reset are:

    AVG ECON TRIP A or TRIP B AVG SPEED

    CHECK

    TRUNK AJAR LTR/100 km

    AIR SUSPENSIONOVERDRIVE OFF

    DOORAJAR

    LOWWASHERFLUID

    DIST TOEMPTY

    TRIPA

    AVGECON

    TRIPB

    INSTECON

    AVGSPEED

    kmMILES/GAL

    RESET E/M SELECT

    Instrumentation

    17

  • E/MPress this control to switch theelectronic instrument cluster displayand the message center display frommetric to English units.

    SelectEach press of the SELECT controlwill select a different function.

    Press the right side of the control toadvance the function to the right,and press the left side of the controlto advance the function to the left.

    To reset any function:

    1. Push either the right or left sideof the SELECT control to choosethe desired function.

    2. Press the RESET control and theselected message center functionwill be reset to zero.

    Message center functionsDIST TO EMPTY (DTE)This function estimatesapproximately how far you can drivewith the fuel remaining in your tankunder normal driving conditions.

    RESET E/M SELECT

    RESET E/M SELECT

    RESET E/M SELECT

    DIST TOEMPTY

    TRIPA

    AVGECON

    TRIPB

    INSTECON

    AVGSPEED

    Instrumentation

    18

  • Remember to turn the ignition OFF when refueling your vehicle.Otherwise, the display will not show the addition of fuel for a few miles.At least 9.5 liters (2.5 gallons) of fuel must be added for the fuel gaugeto immediately show the new fuel level.

    The DTE function will flash for 5 seconds and sound a tone for 1 secondwhen you have approximately:

    80 km (50 miles) left before you run out of fuel 40 km (25 miles) 16 km (10 miles)The message center will remain inthe DTE function until the SELECTcontrol is pressed to changefunctions.

    Displayed DTE will not be equal toAVG ECON multiplied by the FUELREMAIN value. DTE is calculatedusing a method that considers thefuel economy of the last 800 km(500 miles) driven.

    If CO or CS is displayed, there is a problem with the fuel indicationsystem and you should contact your dealer for service as soon aspossible.

    AVG ECON (average fuel economy)Select this function to display youraverage fuel economy in liters/100km or miles/gallon.

    If you calculate your average fueleconomy by dividing miles traveled by gallons used, your figure may bedifferent than displayed for the following reasons:

    your vehicle was not perfectly level during fill-up differences in the automatic shut-off points on the fuel pumps atservice stations

    variations in top-off procedure from one fill-up to another rounding of the displayed values to the nearest 0.1 liter (gallons)

    RESET E/M SELECT

    DIST TOEMPTY

    TRIPA

    AVGECON

    TRIPB

    INSTECON

    AVGSPEED

    Instrumentation

    19

  • Press the RESET control while AVGECON is displayed to reset thefunction.

    The average displayed is the averagesince the last reset.

    INST ECON (instantaneous fuel economy)Select this function to calculate theinstantaneous fuel economy of yourrunning vehicle. For example, youcan see what your fuel economy isin heavy traffic or on an open highway.

    Your vehicle must be moving to calculate instantaneous fuel economy.When your vehicle is not moving, instantaneous fuel economy isdisplayed at 99 liters per 100 kilometers (or 0 miles per gallon).Instantaneous fuel economy cannot be reset.

    TRIP A and TRIP BThese two functions allow you tosee how far you have traveled sinceyou last reset. Trip A and Trip B arecompletely independent and mustbe reset individually.

    To reset either trip feature to zero,press the RESET control while theappropriate trip distance feature(TRIP A or TRIP B) is displayed.

    RESET E/M SELECT

    DIST TOEMPTY

    TRIPA

    AVGECON

    TRIPB

    INSTECON

    AVGSPEED

    DIST TOEMPTY

    TRIPA

    AVGECON

    TRIPB

    INSTECON

    AVGSPEED

    RESET E/M SELECT

    Instrumentation

    20

  • AVG SPEED (average speed)Select this function to display youraverage speed in miles per hour orkilometers per hour.

    Your vehicle must be moving tocalculate your average speed. When your vehicle is not moving, theaverage speed is displayed at 0 kilometers (0 miles) per hour.

    Message center indicator lightsCheck air suspensionBriefly illuminates when the ignitionis turned ON. This light will remainon to indicate that the airsuspension switch is off or toindicate a possible system fault. Formore information on the airsuspension system, refer to theDriving chapter.

    Overdrive offIlluminates when the transmissioncontrol switch (TCS) has beenpushed. When the light is on, thetransmission does not shift intooverdrive. If the light does not comeon when the TCS is depressed or ifthe light flashes when you aredriving, have your vehicle serviced.

    Door ajarIlluminates when one of the doors isnot completely shut and the ignitionis turned to ON. With the ignitionON, this light will flash five timesand sound a tone for one second,then remain on (if a door is open).

    DIST TOEMPTY

    TRIPA

    AVGECON

    TRIPB

    INSTECON

    AVGSPEED

    CHECK

    TRUNK AJAR LTR/100 km

    AIR SUSPENSIONOVERDRIVE OFF

    DOORAJAR

    LOWWASHERFLUID

    kmMILES/GAL

    CHECK

    TRUNK AJAR LTR/100 km

    AIR SUSPENSIONOVERDRIVE OFF

    DOORAJAR

    LOWWASHERFLUID

    kmMILES/GAL

    CHECK

    TRUNK AJAR LTR/100 km

    AIR SUSPENSIONOVERDRIVE OFF

    DOORAJAR

    LOWWASHERFLUID

    kmMILES/GAL

    Instrumentation

    21

  • Low washer fluidMomentarily illuminates when theignition is turned to ON and willstay on when the windshield washerfluid is low.

    Trunk ajarIf the trunk is not completelyclosed, this light comes on whenyou turn the ignition to ON. Withthe ignition ON, this light will flashfive times and sound a tone for onesecond, then remain on (if the trunkis open).

    INDICATOR LAMP MODULEThe indicator lamp module contains the following lamps:

    Anti-lock brake system (ABS) (If equipped)Momentarily illuminates when theignition is turned on and the engineis off. If the light does not illuminatemomentarily at start up, remains onor continues to flash, the ABS needsto be serviced. With the ABS light on, the anti-lock brake system isdisabled and normal braking is still effective unless the brake warninglight also remains illuminated with parking brake released.

    Brake system warningMomentarily illuminates when theignition is turned to the ON positionand the engine is off. If brakewarning lamp does not illuminate atthis time, seek service immediately.Also illuminates when the parking brake is engaged. Illumination afterreleasing the parking brake indicates low brake fluid level and the brakesystem should be inspected immediately.

    CHECK

    TRUNK AJAR LTR/100 km

    AIR SUSPENSIONOVERDRIVE OFF

    DOORAJAR

    LOWWASHERFLUID

    kmMILES/GAL

    CHECK

    TRUNK AJAR LTR/100 km

    AIR SUSPENSIONOVERDRIVE OFF

    DOORAJAR

    LOWWASHERFLUID

    kmMILES/GAL

    ABS

    P!BRAKE

    Instrumentation

    22

  • PANEL DIMMER CONTROLUse to adjust the brightness of theinstrument panel during headlightand parklamp operation.

    Push up to brighten. Push down to dim.HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on the parkinglamps only. Rotate to the secondposition to also turn on theheadlamps.

    High beamsPush forward to activate.

    Flash to passPull toward you to activate andrelease to deactivate.

    PANELDIM

    OFFP

    HILO

    F

    SOFF

    HILO

    F

    SOFF

    Controls and features

    23

  • Autolamp control (if equipped)The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control.

    The autolamp system also keeps thelights on for a preselected period oftime after the ignition switch isturned to OFF.

    To turn autolamps on, rotate thecontrol counterclockwise. The preselected time lapse is adjustable upto approximately three minutes by continuing to rotate the controlcounterclockwise.

    To turn autolamps off, rotate the control clockwise to OFF. A small LED illuminates under the autolamp control to indicate thatthe headlamps have been turned on by the autolamps.

    Daytime running lamps (DRL) (if equipped)Turns the highbeam headlamps on with a reduced output. To activate:

    the engine must be running, the parking brake released, and the headlamp control is in the OFF or Parking lamps position.

    The Daytime Running Light (DRL) system will not illuminate thetail lamps and parking lamps. Turn on your headlamps at dusk.

    Failure to do so may result in a collision.

    REAR WINDOW DEFROSTERThe rear defroster control is locatedon the instrument panel.

    Press the defroster control to clearthe rear window of thin ice and fog.

    The small LED will illuminate when the defroster is activated.The ignition must be in the ON position to operate the rear windowdefroster.

    OFF

    AUTOLAMP

    P

    R.DEF.

    Controls and features

    24

  • The defroster turns off automatically after 10 minutes or when theignition is turned to the OFF position. To manually turn off the defrosterbefore ten minutes have passed, push the control again.

    CLIMATE CONTROL SYSTEM

    Manual heating and air conditioning system (if equipped)

    Fan speed controlControls the volume of air circulatedin the vehicle.

    Temperature control knobControls the temperature of theairflow inside the vehicle.

    Mode selector controlControls the direction of the airflowto the inside of the vehicle.

    The air conditioning compressor will operate in all modes except VENTand FLR. However, the air conditioning will only function if the outsidetemperature is about 10C (50F) or above.

    Since the air conditioner removes considerable moisture from the airduring operation, it is normal if clear water drips on the ground underthe air conditioner drain while the system is working and even after youhave stopped the vehicle.

    LO

    HI

    OFF

    MIX

    VENT FLOOR

    MAXA/C

    NORMA/C

    LO

    HI

    OFF

    MIX

    VENT FLOOR

    MAXA/C

    NORMA/C

    Controls and features

    25

  • Under normal conditions, your vehicles climate control system should beleft in any position other than MAX A/C or OFF when the vehicle isparked. This allows the vehicle to breathe through the outside air inletduct.

    MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisierthan NORM A/C but more economical and will cool the inside of thevehicle faster. Airflow will be from the instrument panel registers. Thismode can also be used to prevent undesirable odors from entering thevehicle.

    NORM A/C-Uses outside air to cool the vehicle. It is quieter than MAXA/C but not as economical. Airflow will be from the instrument panelregisters.

    VENT-Distributes outside air through the instrument panel registers.However, the air will not be cooled below the outside temperaturebecause the air conditioning does not operate in this mode.

    OFF-Outside air is shut out and the fan will not operate. For shortperiods of time only, use this mode to prevent undesirable odors fromentering the vehicle.

    FLR -Allows for maximum heating by distributing outside air throughthe floor ducts. However, the air will not be cooled below the outsidetemperature because the air conditioning does not operate in thismode.

    MIX -Distributes outside air through the windshield defroster ductsand the floor ducts. Heating and air conditioning capabilities areprovided in this mode. For added customer comfort, when thetemperature control knob is anywhere in between the full hot and fullcold positions, the air distributed through the floor ducts will beslightly warmer than the air sent to the windshield defroster ducts. Ifthe temperature is about 10C (50F) or higher, the air conditionerwill automatically dehumidify the air to prevent fogging.

    -Distributes outside air through the windshield defroster ducts. Itcan be used to clear ice or fog from the windshield. If the temperatureis about 10C (50F) or higher, the air conditioner will automaticallydehumidify the air to prevent fogging.

    Operating tips In humid weather, select before driving. This will prevent yourwindshield from fogging. After a few minutes, select any desiredposition.

    Controls and features

    26

  • To prevent humidity buildup inside the vehicle, dont drive with theclimate control system in the OFF position.

    Dont put objects under the front seat that will interfere with theairflow to the back seats.

    Remove any snow, ice or leavesfrom the air intake area (at thebottom of the windshield).

    If your vehicle has been parked with the windows closed during hotweather, the air conditioner will do a much faster job of cooling if youdrive for two or three minutes with the windows open. This will forcemost of the hot, stale air out of the vehicle. Then operate your airconditioner as you would normally.

    When placing objects on top of your instrument panel, be careful tonot place them over the defroster outlets. These objects can blockairflow and reduce your ability to see through your windshield. Also,avoid placing small objects on top of your instrument panel. Theseobjects can fall down into the defroster outlets and block airflow andpossibly damage your climate control system.

    Electronic Automatic Temperature Control (EATC) system(if equipped)The EATC system will maintain aselected temperature andautomatically control airflow. Youcan override automatic operationwith any of the override controls orthe fan speed control.

    NORM A/C VENT FLOOR FLR DEF DEF

    HI

    LOMAX A/C

    OUTSIDE TEMP AUTOMATIC

    OFFF

    AUTO

    Controls and features

    27

  • Turning the EATC onPress AUTOMATIC, any of theoverride controls or the fan speedcontrol. The EATC will only operatewhen the ignition is in the ONposition.

    Turning the EATC offPress OFF. The OutsideTemperature function will continueto operate until the ignition isturned off.

    Automatic operationPress AUTOMATIC and select the desired temperature. The selectedtemperature and the word AUTO will appear in the display window. TheEATC system will either heat or cool to achieve the selectedtemperature. The system will automatically determine fan speed, airflowlocation and if fresh outside air or recirculated air is required. Fan speedremains automatic unless the fan speed thumbwheel is turned.

    When in AUTOMATIC and weather conditions require heat, air will besent to the floor. However, if the engine is not warm enough to provideheat, the fan will be at a low speed and the air will be directed to thewindshield. In 3 minutes or less, the fan speed will start to increaseand the airflow location will change to the floor area.

    If unusual conditions exist (i.e.-window fogging, etc.), the manualoverride controls allow you to select airflow locations and the fan controlallows you to adjust fan speed as necessary.

    NORM A/C VENT FLOOR FLR DEF DEF

    HI

    LOMAX A/C

    OUTSIDE TEMP AUTOMATIC

    OFFF

    AUTO

    FLR DEF DEF

    HI

    LO

    AUTOMATIC

    OFF

    Controls and features

    28

  • Temperature selectionThe display window indicates theselected temperature, function(AUTO or one of the overridecontrols) and manual control of fanspeed ( ) if automatic fan speed is not desired.

    To control the temperature, selectany temperature between 18C(65F) and 29C (85F) by pressingthe blue (cooler) or red (warmer)buttons.

    For continuous maximum cooling, push the blue button until 16C(60F) is shown in the display window. The EATC will continuemaximum cooling (disregarding the displayed temperature) until awarmer temperature is selected by pressing the red button.

    For continuous maximum heating, push the red button until 32C (90F)is shown in the display window. The EATC will continue maximumheating (disregarding the displayed temperature) until a coolertemperature is selected by pressing the blue button.

    Temperature conversionPress MAX A/C and DEF at thesame time (for one second) toswitch between Fahrenheit andCelsius.

    If your vehicle has an English/Metric (E/M) control to change yourelectronic instrument cluster display (if equipped) and the messagecenter display (if equipped) from English to Metric, this control will alsochange the temperature display. Refer to Electronic Message Center inthe Instrumentation Chapter.

    FAUTO

    NORM A/C VENTMAX A/C

    OUTSIDE TEMP

    NORM A/C VENT FLOOR FLR DEF DEF

    HI

    LOMAX A/C

    OUTSIDE TEMP AUTOMATIC

    OFF

    AUTO

    Controls and features

    29

  • Fan speed ( )When AUTOMATIC is pressed, fanspeed is adjusted automatically forexisting conditions. You can overridefan speed at any time. To controlfan speed manually, use thethumbwheel to cancel automatic fanspeed operation. Rotate thethumbwheel up for higher fan speedor down for lower fan speed.

    The display will show to indicatemanual fan operation.

    To return to automatic fan operation, press AUTOMATIC.

    Manual override controlsThe override controls are located atthe bottom of the EATC and allowyou to determine where airflow isdirected. To return to full automaticcontrol, press AUTOMATIC.

    The air conditioning compressor will operate in all modes except FLOORand VENT. It will also operate only when required when AUTOMATIChas been selected. However, the air conditioning will only function if theoutside temperature is about 10C (50F) or above.

    Since the air conditioner removes considerable moisture from the airduring operation, it is normal if clear water drips on the ground underthe air conditioner drain while the system is working and even after youhave stopped the vehicle.

    Under normal conditions, your vehicles climate control system should beleft in any position other than MAX A/C or OFF when the vehicle isparked. This allows the vehicle to breathe through the outside air inletduct.

    FLR DEF DEF

    HI

    LO

    AUTOMATIC

    OFF

    FAUTO

    NORM A/C VENT FLOOR FLR DEF DEF

    HI

    LOMAX A/C

    OUTSIDE TEMP AUTOMATIC

    OFFF

    AUTO

    Controls and features

    30

  • MAX A/C-Uses recirculated air to cool the vehicle. The temperaturedisplay will remain the same and air will be cooled based on theselected temperature. To exit, press AUTOMATIC or any otheroverride controls. MAX A/C is noisier than NORM A/C but moreeconomical and will cool the inside of the vehicle faster. Airflow isfrom the instrument panel registers. This mode can also be used toprevent undesirable odors from entering the vehicle.

    NORM A/C-Uses outside air to cool the vehicle. The temperaturedisplay will remain the same and air will be cooled based on theselected temperature. It is quieter than MAX A/C but not aseconomical. Fan speed will remain automatic. Airflow is from theinstrument panel registers.

    VENT-Distributes outside air through the instrument panel registers.However, the air cannot be cooled below the outside temperaturebecause the air conditioning does not operate in this mode.

    FLOOR -Allows for maximum heating by distributing outside airthrough the floor ducts. However, the air cannot be cooled below theoutside temperature because the air conditioning does not operate inthis mode.

    FLR DEF-Distributes outside air through the windshield defrosterducts and the floor ducts. Heating and air conditioning capabilities areprovided in this mode. The air will be heated or cooled based on thetemperature selection. For added customer comfort, the airdistributed through the floor ducts will be slightly warmer than the airsent to the windshield defroster ducts. If the temperature is about10C (50F) or higher, the air conditioner will automaticallydehumidify the air to prevent fogging.

    DEF -Distributes outside air through the windshield defrosterducts. It can be used to clear ice or fog from the windshield. If theoutside air temperature is about 10C (50F) or higher, the airconditioner will automatically dehumidify the air to prevent fogging.

    OFF-Outside air is shut out and the fan will not operate. For shortperiods of time, use this mode to prevent undesirable odors fromentering the vehicle. For short periods of time only, use this mode toprevent undesirable odors from entering the vehicle.

    Controls and features

    31

  • Displaying outside temperaturePress OUTSIDE TEMP to displaythe outside air temperature. It willbe displayed until OUTSIDE TEMPis pressed again.

    If the selected temperature is changed while the outside temperature isdisplayed, the new temperature will be displayed for four seconds after itis changed, then the outside temperature will return to the window.

    If a manual override function is selected while the outside temperature isdisplayed, the new function will be displayed for four seconds after it ischanged, then the outside temperature will return to the window alongwith the override selection.

    The outside temperature reading is most accurate when the vehicle ismoving. Higher readings may be obtained when the vehicle is notmoving. The readings that you get may not agree with temperaturesgiven on the radio due to differences in vehicle and station locations.

    Operating tips In humid weather, select DEF before driving. This will preventyour windshield from fogging. After a few minutes, select any desiredposition.

    To prevent humidity buildup inside the vehicle, dont drive with theclimate control system in the OFF position.

    Dont put objects under the front seat that will interfere with theairflow to the back seats.

    NORM A/C VENTMAX A/C

    OUTSIDE TEMP

    Controls and features

    32

  • Remove any snow, ice or leavesfrom the air intake area (at thebottom of the windshield).

    If your vehicle has been parked with the windows closed during hotweather, the air conditioner will do a much faster job of cooling if youdrive for two or three minutes with the windows open. This will forcemost of the hot, stale air out of the vehicle. Then operate the airconditioner as you would normally.

    When placing objects on top of your instrument panel, be careful tonot place them over the defroster outlets. These objects can blockairflow and reduce your ability to see through your windshield. Also,avoid placing small objects on top of your instrument panel. Theseobjects can fall down into the defroster outlets and block airflow andpossibly damage your climate control system.

    CLOCKPress H to set the hour.

    Press M to set the minute.

    AUDIO SYSTEMRefer to the Audio Guide in your owner portfolio.

    H M

    H M

    Controls and features

    33

  • TURN SIGNAL CONTROL Push down to activate the leftturn signal.

    Push up to activate the right turnsignal.

    The flash rate of the turn signal will speed up considerably if theLighting Control Module detects a left or right turn lamp bulb (front orrear) is burned out.

    Cornering lampsWhen the turn signal is used when the headlamps are on, the corneringlamps will light either the right or left side depending on the direction ofthe turn.

    WINDSHIELD WIPER/WASHER CONTROLSRotate the windshield wiper controlto the desired interval, low or highspeed position.

    The bars of varying length are forintermittent wipers. When in thisposition rotate the control upwardfor fast intervals and downward forslow intervals.

    Push the control on the end of thestalk to activate washer. Push andhold for a longer wash cycle. Thewasher will automatically shut offafter ten seconds of continuous use.

    HILO

    F

    SOFF

    HILO

    F

    SOFF

    HILO

    F

    SOFF

    Controls and features

    34

  • POSITIONS OF THE IGNITION1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.

    2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal.

    3. OFF, shuts off the engine and allaccessories without locking thesteering wheel.

    4. ON, all electrical circuits operational. Warning lights illuminated. Keyposition when driving.

    5. START, cranks the engine. Release the key as soon as the enginestarts.

    TILT STEERINGPull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control.

    Never adjust the steering wheel when the vehicle is moving.

    3

    1

    2

    5

    4

    Controls and features

    35

  • SPEED CONTROL (IF EQUIPPED)To turn speed control on Press ON.Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph).

    Do not use the speed control in heavy traffic or on roads thatare winding, slippery, or unpaved.

    Do not shift the gearshift lever into N (Neutral) with the speedcontrol on.

    To turn speed control off Press OFF or Turn off the vehicle ignition.

    Once speed control is switched off, the previously programmed set speedwill be erased.

    OFF

    ON

    OFF

    ON

    Controls and features

    36

  • To set a speed Press SET ACC/SET ACCEL. Forspeed control to operate, thespeed control must be ON andthe vehicle speed must be greaterthan 48 km/h (30 mph).

    If you drive up or down a steep hill, your vehicle speed may varymomentarily slower or faster than the set speed. This is normal.

    Speed control cannot reduce the vehicle speed if it increases above theset speed on a downhill. If your vehicle speed is faster than the setspeed while driving on a downhill, you may want to shift to the nextlower gear or apply the brakes to reduce your vehicle speed.

    If your vehicle slows down more than 16 km/h (10 mph) below your setspeed on an uphill, your speed control will disengage. This is normal.Pressing RES/RSM/RESUME will re-engage it.

    Do not use the speed control in heavy traffic or on roads thatare winding, slippery, or unpaved.

    To set a higher set speed Press and hold SET ACC/SETACCEL. Release the control whenthe desired vehicle speed isreached or

    Press and release SET ACC/SETACCEL. Each press will increasethe set speed by 1.6 km/h(1 mph) or

    Accelerate with your acceleratorpedal. When the desired vehiclespeed is reached, press and release SET ACC/SET ACCEL.

    COAST

    RESUME

    SETACCEL

    COAST

    RESUME

    SETACCEL

    Controls and features

    37

  • You can accelerate with the accelerator pedal at any time during speedcontrol usage. Releasing the accelerator pedal will return your vehicle tothe previously programmed set speed.

    To set a lower set speed Press and hold CST/COAST.Release the control when thedesired speed is reached or

    Press and release CST/COAST.Each press will decrease the setspeed by 1.6 km/h (1 mph) or

    Depress the brake pedal. Whenthe desired vehicle speed isreached, press SET ACC/SETACCEL.

    To disengage speed control Depress the brake pedal.Disengaging the speed control willnot erase the previouslyprogrammed set speed.

    COAST

    RESUME

    SETACCEL

    COAST

    RESUME

    SETACCEL

    Controls and features

    38

  • Pressing OFF will erase thepreviously programmed set speed.

    To return to a previously set speed Press RES/RSM/RESUME. ForRES/RSM/RESUME to operate,the vehicle speed must be fasterthan 48 km/h (30 mph).

    Indicator lightThis light comes on when either theSET ACC/SET ACCEL orRES/RSM/RESUME controls arepressed. It turns off when the speed control OFF control is pressed, thebrake is applied or the ignition is turned to the OFF position.

    HOMELINKT UNIVERSAL TRANSMITTER (IF EQUIPPED)The HomeLinkt Universal Transmitter, located underneath the driversvisor, provides a convenient way to replace up to three hand-heldtransmitters with a single built-in device. This feature will learn the radiofrequency codes of most current transmitters to operate garage doorsand gates, and can also control home or office lighting and securitysystems (with the available accessory package).

    OFF

    ON

    COAST

    RESUME

    SETACCEL

    SPEED CONTROL

    Controls and features

    39

  • When programming your HomeLinkt Universal Transmitter, youwill be operating the garage door or gate. Be sure that people

    and objects are out to the way to prevent potential harm or damage.

    Do not use the HomeLinkt Universal Transmitter with any garage dooropener that lacks safety stop and reverse features as required by U.S.federal safety standards (this includes any garage door opener modelmanufactured before April 1, 1982). A garage door which cannot detectan object, signaling the door to stop and reverse, does not meet currentU.S. federal safety standards. For more information on this matter, calltoll-free: 18003553515.

    Programming1. Prepare for programming theHomeLinkt Universal Transmitter byerasing all three of the factorydefault channels by holding downthe two outside controls until thered light begins to flash (20-30seconds). Release both controls.

    2. Hold the end of your hand-heldtransmitter against the HomeLinktUniversal Transmitter (located onyour visor) while keeping the red light in view.

    3. Using both hands, press thehand-held transmitter control andthe desired channel control on theHomeLinkt Universal Transmitter.Do not release the controls untilstep 4 has been completed.

    4. Hold down both controls until thered light begins to flash slowly andthen rapidly. Rapid flashing indicatessuccessful programming of the newfrequency signal.

    5. Follow steps 2 through 4 to program the remaining two channels.

    If you do not successfully program the HomeLinkt Universal Transmitterafter repeated attempts, refer to Training a rolling code which followsor call toll-free customer assistance: 18003553515.

    Controls and features

    40

  • Note to Canadian residentsDuring programming, your hand-held transmitter may automatically stoptransmitting after two seconds which may not be long enough toprogram the HomeLinkt Universal Transmitter.

    If you are programming from one ofthese hand-held transmitters:

    continue to hold the control onthe HomeLinkt UniversalTransmitter

    re-press the hand-heldtransmitter every two seconds

    You may have to repeat this functionseveral times while programming.

    Operating the HomeLinkT Universal TransmitterOnce programmed, the HomeLinktUniversal Transmitter can be used inplace of hand-held transmitters. Tooperate, simply press theappropriate channel control on thetransmitter (the red light willilluminate, indicating the signal isbeing transmitted).

    Training a rolling code systemRolling code systems (garage door openers which are code protected)may be determined by the following:

    The hand-held transmitter appears to program the HomeLinktUniversal Transmitter but does not activate the garage door.

    The garage door opener was manufactured after 1995.Follow these steps to train a garage door with the rolling code feature:

    1. Locate the training control on the garage door opener receiver. Referto the garage door opener manual or call 18003553515 if there isdifficulty locating the training control.

    Controls and features

    41

  • 2. Press the training control on the garage door opener receiver until thetraining light (next to the control) begins to flash (1-2 seconds).

    3. Press the programmedHomeLinkt control in the vehicleuntil the training light on the garagedoor receiver turns solid (1-2seconds). Release the HomeLinktcontrol and repress to turn off thetraining light.

    4. Press the HomeLinkt controlagain. If the garage door activates,the HomeLinkt UniversalTransmitter has been trained to the receiver.

    Erasing channelsTo erase all three programmedchannels:

    1. Hold down the two outsidecontrols until the red light begins toflash.

    2. Release both controls.

    Channels cannot be erasedindividually, but can bereprogrammed. Refer toProgramming for instructions.

    AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED)Your vehicle is equipped with an inside rear view mirror which has anauto-dimming function. The electronic day/night mirror will change fromthe normal state to the non-glare state when bright lights (glare) reachthe mirror. When the mirror detects bright light from front or behind, itwill automatically adjust (darken) to minimize glare.

    Do not block the sensor on the backside of the mirror since this mayimpair proper mirror performance.

    Controls and features

    42

  • Press the control to turn the mirroron or off.

    The mirror will automatically returnto the normal state whenever thevehicle is placed in R (Reverse)(when the mirror is on) to ensure abright clear view when backing up.

    ELECTRONIC COMPASS (IF EQUIPPED)The compass reading will remain accurate during most drivingconditions. Unknown to the driver, the compass is continuouslyrecalibrating due to magnetic fields and subtle, slow changes in vehiclemagnetics which can occur over the life of the vehicle.

    The compass reading will remain fixed when significant levels areexperienced (such as steel bridges). The compass will return to normaloperation upon leaving the magnetized area.

    If highly magnetized items (such as magnetic mount antennas) areplaced very near the compass the display will change to C for 15seconds, then display all segments until the magnetized item is removed.

    Most geographic areas (zones) have a magnetic north compass point thatvaries slightly from the northerly direction on maps. This variation is fourdegrees between adjacent zones and will become noticeable as thevehicle crosses multiple zones. A correct zone setting will eliminate thiserror. Refer to Compass zone adjustment.

    COMP MIRROR

    Controls and features

    43

  • Compass zone adjustment1. Determine which compass zoneyou are in by referring to the zonemap.

    2. With the compass display turnedon, press and hold the COMP side ofthe control until the zone selectionnumber appears in the mirrordisplay window.

    3. Release the COMP side of thecontrol, then press it down again.

    4. Continue to press until your zonenumber is shown in the mirrordisplay, then release.

    5. The display will show all segments, then return to normal compassmode within ten seconds.

    Compass calibration adjustmentPerform this adjustment in an open area free from steel structures andhigh voltage lines.

    1. Start the vehicle.

    1

    23

    4

    56

    7 8 9

    10

    11

    12

    13

    1415

    COMP MIRROR

    NW

    Controls and features

    44

  • 2. Press and hold the COMP side ofthe control for approximately sixseconds until C appears in themirror display.

    3. Drive the vehicle slowly (lessthan 5 km/h [3 mph]) in circles oron your everyday routine until thedisplay reads a direction.

    4. The compass is now calibrated.

    TRUNK REMOTE CONTROLThe remote trunk release control islocated on the drivers door trimpanel and can be operated at anytime.

    COMP MIRROR

    NW

    TRUNK

    Controls and features

    45

  • POWER WINDOWSPress and hold the rocker switches to open and close windows.

    Press the top portion of therocker switch to close.

    Press the bottom portion of therocker switch to open.

    Express down Press AUTO and release quickly.The window will open fully.Depress again to stop windowoperation.

    AUTO

    AUTO

    AUTO

    Controls and features

    46

  • Window lockThe window lock feature allows onlythe driver to operate the powerwindows.

    To lock out all the window controlsexcept for the drivers press theright side of the control. Press the left side to restore the windowcontrols.

    POWER DOOR LOCKS (IF EQUIPPED)Press U to unlock all doors and L tolock all doors.

    POWER SIDE VIEW MIRRORSThe ignition must be in ACC or ON position to adjust the power sideview mirrors.

    To adjust your mirrors:

    1. Select L to adjust the left mirroror R to adjust the right mirror.

    WINDOW LOCK

    U L

    MIRRORSL R

    Controls and features

    47

  • 2. Move the control in the directionyou wish to tilt the mirror.

    3. Return to the center position to lock mirrors in place.

    CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoors are unlocked.

    The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one doorwill not automatically set the lockfor both doors.

    Move lock control up to engage thelock. Move control down todisengage childproof locks.

    MIRRORSL R

    Controls and features

    48

  • POSITIVE RETENTION FLOOR MATPosition the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tolock in. Make sure that the mat doesnot interfere with the operation ofthe accelerator or the brake pedal.To remove the floor mat, reverse theinstallation procedure.

    REMOTE ENTRY SYSTEM (IF EQUIPPED)The remote entry system allows you to lock or unlock all vehicle doorswithout a key.

    The remote entry features only operate with the ignition in the OFFposition.Unlocking the doorsPress this control to unlock thedriver door. The interior lamps willilluminate.

    Press the control a second timewithin five seconds to unlock alldoors.

    Locking the doorsPress this control to lock all doors.

    The horn will chirp and theparklamps/taillamps will flash toconfirm the control was pressed.This feature can be turned on/offwith the keyless entry keypadthrough the following procedure:

    1. Enter the keyless entry keypadfactory code.

    Controls and features

    49

  • 2. Within 5 seconds, press and hold control 7/8.

    3. Within 5 seconds (while holding down control 7/8), press and releasecontrol 1/2.

    4. Release control 7/8.

    The door will lock/unlock to confirm the horn chirp feature has beendisabled. Once disabled, the feature can be enabled by repeating thesame sequence.

    AutolockThis feature automatically locks all doors when:

    all vehicle doors are closed the ignition is in the ON position you shift into or through R (Reverse) the brake pedal is released.RelockThe autolock feature repeats when:

    any door is opened and closed the brake pedal is released.Deactivating/activating the autolock featureBefore following the procedure, make sure that the ignition is OFF andall vehicle doors are closed.

    You must complete steps 1-5 within 30 seconds or the procedure willhave to be repeated. If the procedure needs to be repeated, you mustwait 30 seconds.

    1. Turn the ignition key to ON.

    2. Press the power door unlock control three times.

    3. Turn the ignition key from ON to OFF.

    4. Press the power door unlock control three times.

    5. Turn the ignition back to ON. The horn will chirp.

    6. Press the unlock control, then press the lock control. The horn willchirp once if autolock was deactivated or twice (one short and one longchirp) if autolock was activated.

    Controls and features

    50

  • 7. Turn the ignition to OFF. The horn will chirp once to confirm theprocedure is complete.

    Opening the trunkPress the control once to open thetrunk.

    Ensure that the trunk is closed andlatched before driving your vehicle.Failure to latch the trunk may causeobjects to fall out of the trunk orblock the rear view.

    Sounding a panic alarmPress this control to activate thealarm.

    To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON.

    This device complies with part 15 ofthe FCC rules and with RS-210 ofIndustry Canada. Operation issubject to the following twoconditions: (1) This device may notcause harmful interference, and (2) This device must accept anyinterference received, including interference that may cause undesiredoperation.

    Changes or modifications not expressly approved by the partyresponsible for compliance could void the users authority tooperate the equipment.

    Illuminated entryThe interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm.

    The system automatically turns off after 25 seconds or when the ignitionis turned to the START or ACC position. The dome lamp control (ifequipped) must not be set to the OFF position for the illuminated entrysystem to operate.

    Controls and features

    51

  • The inside lights will not turn off if:

    they have been turned on with the dimmer control or any door is open.The battery saver will shut off the interior lamps 30 minutes after thelast door is closed.

    Replacing the batteryThe transmitter is powered by one coin type three-volt lithium batteryCR2032 or equivalent. Typical operating range will allow you to be up to10 meters (33 feet) away from your vehicle. A decrease in operatingrange can be caused by:

    battery weakness due to time and use weather conditions nearby radio towers structures around the vehicle other vehicles parked next to the vehicleTo replace the battery:

    1. Twist a thin coin between the two halves of the transmitter near thekey ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTERAPART.

    2. Place the positive (+) side of new battery in the same orientation.Refer to the diagram inside the transmitter unit.

    3. Snap the two halves back together.

    Replacement of the battery will not cause the remote transmitter tobecome deprogrammed from your vehicle. The remote transmitter shouldoperate normally after battery replacement.

    Controls and features

    52

  • Replacing lost transmittersTake all your vehicles transmittersto your dealer for reprogramming if:

    a transmitter is lost or you want to purchase additionaltransmitters (up to four may beprogrammed).

    SECURILOCKY ANTI-THEFT SYSTEMThe SecuriLocky anti-theft system provides an advanced level of vehicletheft protection. Your vehicles engine can only be started with the twospecial SecuriLocky electronically coded keys provided with yourvehicle. Each time you start your vehicle, the SecuriLocky key is readby the SecuriLocky anti-theft system. If the SecuriLocky keyidentification code matches the code stored in the SecuriLockyanti-theft system, the vehicles engine is allowed to start. If theSecuriLocky key identification code does not match the code stored inthe system or if a SecuriLocky key is not detected (vehicle theftsituation), the vehicles engine will not operate.

    Spare SecuriLocky keys can be purchased from your dealership andprogrammed to your SecuriLocky anti-theft system. Refer toProgramming spare SecuriLocky keys for more information.

    If one or both of your SecuriLocky keys are lost or stolen and you wantto ensure the lost or stolen key will not operate your vehicle, bring yourvehicle and all available SecuriLocky keys to your dealership forreinitialization.

    Theft indicatorThe theft indicator on top of the instrument panel will operate as follows:

    When the ignition is OFF, the theft indicator will flash briefly every2 seconds to indicate the SecuriLocky system is protecting yourvehicle.

    When the ignition is turned to RUN or START, the theft indicator willlight for 3 seconds and then go out. If the theft indicator stays on foran extended period of time or flashes rapidly, have the systemserviced by your dealership or a qualified technician.

    Controls and features

    53

  • Programming spare SecuriLockY keysSpare SecuriLocky keys can be purchased from your dealership andprogrammed to your SecuriLocky anti-theft system (up to a total of8 keys). Your dealership can program your new SecuriLocky key(s) toyour vehicle or you can do it yourself using the following simpleprocedure. To program a new SecuriLocky key yourself, you will needtwo previously programmed SecuriLocky keys (keys that alreadyoperate your vehicles engine). If two previously programmedSecuriLocky keys are not available (one or both of your original keyswere lost or stolen), you must bring your vehicle to your dealership tohave the spare SecuriLocky key(s) programmed.

    Procedure to program spare SecuriLockY keys to your vehicleNew SecuriLocky keys must have the correct mechanical key cut foryour vehicle.

    Conventional (non-SecuriLocky) keys cannot be programmed to yourvehicle.

    You will need to have two previously programmed SecuriLocky keys andthe new unprogrammed SecuriLocky key readily accessible for timelyimplementation of each step in the procedure. Please read andunderstand the entire procedure before you begin.

    1. Insert the first previously programmed SecuriLocky key into theignition and turn the ignition from OFF to RUN (maintain ignition inRUN for at least one second).

    2. Turn ignition to OFF and remove the first SecuriLocky key from theignition.

    3. Within five seconds of turning the ignition to OFF, insert the secondpreviously programmed SecuriLocky key into the ignition and turn theignition from OFF to RUN (maintain ignition in RUN for at least onesecond but no more than 5 seconds).

    4. Turn the ignition to OFF and remove the second SecuriLocky keyfrom the ignition.

    5. Within 10 seconds of turning the ignition to OFF, insert theunprogrammed SecuriLocky key (new key) into the ignition and turnthe ignition from OFF to RUN (maintain ignition in RUN for at least onesecond). This step will program your new SecuriLocky key.

    6. If it is desired to program additional SecuriLocky key(s), repeat thisprocedure from step 1.

    Controls and features

    54

  • If the programming procedure was successful, the new SecuriLockykey(s) will start the vehicles engine. The theft indicator (located on theinstrument panel) will light for three seconds and then go out.

    If the programming procedure was not successful, the new SecuriLockykey(s) will not operate the vehicles engine. The theft indicator will flashon and off. Wait at least one minute and then repeat the procedure fromstep 1. If failure repeats, bring your vehicle to your dealership to havethe spare SecuriLocky key(s) programmed.

    KEYLESS ENTRY SYSTEMWith the keyless entry keypad, youcan:

    lock or unlock the vehicle doorswithout using the key.

    disable/enable horn chirp. disable/enable autolockSee also Remote entry system in this chapter for more information.

    Your vehicle has a factory-set 5 digit code that operates the keyless entrysystem. You can also program your own 5 digit personal entry code.

    The factory-set code is located:

    on the owners wallet card in the glove compartment taped to the computer moduleWhen pressing the controls on the keyless entry keypad, press themiddle of the controls to ensure a good activation.

    Programming your own entry code1. Enter the factory-set code (keypad will illuminate when pressed).

    2. Press the 1/2 control within fiveseconds of step 1.

    3. Enter your personal 5 digit code.Enter each digit within five secondsof the previous one.

    All of the vehicle doors will lock and unlock to confirm programming ofthe new code.

    Do not set a code that includes five of the same number or presents themin sequential order. Thieves can easily figure out these types of codes.

    1 2 3 4 5 6 7 8 9 0

    1 2 3 4 5 6 7 8 9 0

    Controls and features

    55

  • You can program up to three personal codes to unlock your vehicle. Thesecodes do not replace the permanent code that the dealership gave you.

    Erasing personal codeTo erase all of the personal entry codes programmed to a vehicle:

    1. Enter the factory-set code.

    2. Press 1/2 within 5 seconds ofstep 1.

    3. Press and hold 1/2 for twoseconds. All of the vehicle doors willlock and then unlock to confirm erasure.

    Unlocking the doors and releasing the trunk with the keyless entrysystemTo unlock the driver door, enter either the factory-set code or personalcode (each digit pressed within 5 seconds of prior digit). The interiorlamps will illuminate.

    To unlock all doors, enter thefactory-set code or personal code(driver door unlocks) and press 3/4within 5 seconds.

    To release the trunk, enter thefactory-set code or personal code(driver door unlocks) and press 5/6within 5 seconds.

    After the factory-set code or personal code has been entered, you canunlock all doors (press 3/4) and release the trunk (press 5/6) as long asthe controls are pressed within 5 seconds of each other.

    Locking doors with the keyless entry systemIt is not necessary to enter the factory-set code prior to locking all doors.To lock the doors:

    1. Press 7/8 and 9/0 at the sametime.

    1 2 3 4 5 6 7 8 9 0

    1 2 3 4 5 6 7 8 9 0

    1 2 3 4 5 6 7 8 9 0

    1 2 3 4 5 6 7 8 9 0

    Controls and features

    56

  • SEATING

    Head restraintsPush or pull the head rests to thedesired position.

    Front seats

    Never adjust the drivers seat or seatback when the vehicle ismoving.

    Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop.

    Always drive and ride with your seatback upright and the lapbelt snug and low across the hips.

    Lift handle to move seat forward orbackward.

    Seating and safety restraints

    57

  • Pull lever up to adjust seatback.

    Using the manual recline function (if equipped)Never adjust the drivers seat or seatback when the vehicle ismoving.

    Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop.

    Always drive and ride with your seatback upright and the lapbelt snug and low across the hips.

    To adjust the front seatback usingthe manual recliner:

    Lift and hold the handle locatedon the side of the seat.

    Lean against the seatback toadjust it to your desired position.You can recline the seat back orbring it forward.

    Release the handle when the desired position has been reached.Adjusting the power front seats door mounted controlsThe controls for the power seats are located on the inside of each frontdoor.

    Never adjust the drivers seat or seatback when the vehicle ismoving.

    Seating and safety restraints

    58

  • Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop.

    Always drive and ride with your seatback upright and the lapbelt snug and low across the hips.

    Press the control to recline theseatback forward or backward. (ifequipped)

    Press to move the seat forward orbackward.

    Press to move the front portion ofthe seat cushion up or down.

    Seating and safety restraints

    59

  • Press to move the rear portion ofthe seat cushion up or down.

    Adjusting the power seats seat mounted controlsNever adjust the drivers seat or seatback when the vehicle ismoving.

    The power seat controls are locatedon the side of the drivers seat.

    Press to raise or lower the seat, orto move the seat forward orbackward.

    Using the power lumbar supportThe power lumbar control is locatedon the outboard side of the seat.

    Press one side of the control toadjust firmness.

    Press the other side of the controlto adjust softness.

    SAFETY RESTRAINTS

    Safety restraints precautionsAlways drive and ride with your seatback upright and the lapbelt snug and low across the hips.

    Seating and safety restraints

    60

  • To prevent the risk of injury, make sure children sit where theycan be properly restrained.

    Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from

    injury in a collision.

    All occupants of the vehicle, including the driver, should alwayswear their safety belts.

    It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas

    are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone in your vehicle is in a seat and using asafety belt properly.

    Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that

    are designed to be used as a pair. 1) Use the shoulder belt on theoutside shoulder only. Never wear the shoulder belt under the arm. 2)Never swing it around your neck over the inside shoulder. 3) Never usea single belt for more than one person.

    Combination lap and shoulder belts1. To fasten, insert the tongue intothe slot in the buckle.

    Seating and safety restraints

    61

  • 2. To unfasten, push the red releasebutton and remove the tongue fromthe buckle.

    The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front and rear seat passengeroutboard safety belts have two types of locking modes described below:

    Vehicle sensitive modeThe vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustment to your movements and locking inresponse to vehicle movement. For example, if the driver brakessuddenly or turns a corner sharply, or the vehicle receives an impact of 8km/h (5 mph) or more, the combination safety belts will lock to helpreduce forward movement of the driver and passengers.

    In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt.

    The automatic locking mode is not available on the driver safety belt.

    When to use the automatic locking mode When a tight lap/shoulder fit is desired. Anytime a child safety seat is installed in the vehicle. Refer to SafetyRestraints for Children or Safety Seats for Children later in thischapter.

    Seating and safety restraints

    62

  • How to use the automatic locking mode Buckle the combination lap andshoulder belt.

    Grasp the shoulder portion andpull downward until the entirebelt is extracted.

    Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode.

    How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode.

    Seating and safety restraints

    63

  • Front safety belt height adjustmentYour vehicle has safety belt heightadjustments for the driver and frontpassenger. Adjust the height of theshoulder belt so the belt restsacross the middle of your shoulder.

    To lower the shoulder belt height,push the button and slide the heightcontrol down. To raise the height ofthe shoulder belt, slide the heightadjuster up. Pull down on the heightadjustment assembly to make sure itis locked in place.

    Position the shoulder beltheight adjuster so that the

    belt rests across the middle ofyour shoulder. Failure to adjustthe safety belt properly couldreduce the effectiveness of thesafety belt and increase the risk ofinjury in a collision.

    Lap beltsAdjusting the lap beltThe lap belt does not adjust automatically. Adjust to fit snugly and as lowas possible around your hips. Do not wear the lap belt around your waist.

    Seating and safety restraints

    64

  • Insert the tongue into the correctbuckle. To lengthen the belt, turnthe tongue at a right angle to thebelt and pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it fitssnugly across the hips.

    Shorten and fasten the belt whennot in use.

    Safety belt extension assemblyIf the safety belt assembly is too short, even when fully extended, 20 cm(8 inches) can be added to the safety belt assembly by adding a safetybelt extension assembly (part number 611C22). Safety belt extensionassemblies can be obtained from your dealer at no cost.

    Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label. Also, use the safety belt extension only if the safety belt is tooshort for you when fully extended. Do not use extensions to change thefit of the shoulder belt across the torso.

    Safety belt warning light and indicator chimeThe seat belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts.

    Seating and safety restraints

    65

  • Conditions of operation

    If... Then...The drivers safety belt is notbuckled before the ignitionswitch is turned to the ONposition...

    The safety belt warning lightilluminates for one to two minutes andthe warning chime sounds for four toeight seconds.

    The drivers safety belt isbuckled while the indicatorlight is illuminated and thewarning chime is sounding...

    The safety belt warning light andwarning chime turn off.

    The drivers safety belt isbuckled before the ignitionswitch is turned to the ONposition...

    The safety belt warning light andindicator chime remain off.

    Safety belt maintenanceCheck the safety belt systems periodically to make sure they workproperly and are not damaged. Check the safety belts to make sure thereare no nicks, wears or cuts. All safety belt assemblies, includingretractors, buckles, front seat belt buckle assemblies (slide bar)(ifequipped), shoulder belt height adjusters (if equipped), child safety seattether bracket assemblies (if equipped), and attaching hardware, shouldbe inspected after a collision. Ford recommends that all safety beltassemblies used in vehicles involved in a collision be replaced. However,if the collision was minor and a qualified technician finds that the beltsdo not show damage and continue to operate properly, they do not needto be replaced. Safety belt assemblies not in use during a collision shouldalso be inspected and replaced if either damage or improper operation isnoted.

    Failure to replace the safety belt assembly under the aboveconditions could result in severe personal injuries in the event of

    a collision.

    Refer to Cleaning and maintaining the safety belts in theMaintenance and care section.

    Seating and safety restraints

    66

  • AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

    Important supplemental restraint system (SRS) precautionsThe supplemental restraint systemis designed to work with the safetybelt to help protect the driver andright front passenger from certainupper body injuries.

    Air bags DO NOT inflate slowly orgently and the risk of injury from adeploying air bag is greatest close tothe trim covering the air bagmodule.

    All occupants of the vehicle including the driver should alwaysproperly wear their safety belts even when air bag SRS is

    provided.

    Always transport children 12 years old and under in the backseat and always use appropriate child restraints.

    NHTSA recommends a minimum distance of at least 25.4 cm(ten [10] inches) between an occupants chest and the air bag

    module.

    HILO

    F

    SOFF

    E

    CHECKENGINE

    AIRSUSP

    ODOFF

    BRAKE

    TEMP OILVOLTS FUEL

    MPH km/h10

    20

    30

    4050

    60 7080

    90

    100

    110

    12020

    40

    60

    80100

    120

    140

    160

    180

    200

    HH

    LC

    FH

    L< FUEL FILL DOOR

    NORM A/C VENT FLOOR FLR DEF DEF

    HI

    LOMAX A/C

    OUTSIDE TEMP AUTOMATIC

    OFFF

    AUTO

    REWSIDE 1-2

    FFSCAN EJ

    BASS TREB BAL FADE

    VOL - PUSH ON

    SEEK

    TUNE

    1 2 3 4 5 6

    fw DOLBY B NR

    FM1 ST

    CD

    CLKAMFM

    TAPEAMS

    R.DEF.

    AUTOLAMP

    0FF

    PANELDIM

    PUSH INTERIOR

    H M

    P R N D 2 1

    OFF

    ON

    RSM

    SETACC

    COAST

    10:35

    Seating and safety restraints

    67

  • Steps you can take to properly position yourself away from the airbag:

    Move your seat to the rear as far as you can while still reaching thepedals comfortably.

    Recline the seat one or two notches from the upright position.The right front passenger air bag is not designed to restrainoccupants in the center front seating position.

    Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those

    objects to be propelled by the air bag into your face and torso causingserious injury.

    Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its fuses. See your Ford or

    Lincoln-Mercury dealer.

    Children and air bagsFor additional important safetyinformation, read all information onsafety restraints in this guide.

    Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision.

    Seating and safety restraints

    68

  • Air bags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active air bag. If you must

    use a forward-facing child seat in the front seat, move the seat all theway back.

    How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decelerationsufficient to cause the sensors toclose an electrical circuit thatinitiates air bag inflation.

    The fact that the air bags did notinflate in a collision does not meanthat something is wrong with thesystem. Rather, it means the forceswere not of the type sufficient tocause activation. Air bags are designed to inflate in frontal andnear-frontal collisions, not rollover, side-impact, or rear-impacts.

    The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion process that inflates theair bag. Small amounts of sodiumhydroxide may be present whichmay irritate the skin and eyes, butnone of the residue is toxic.

    While the system is designed to helpreduce serious injuries, it may alsocause minor burns, abrasions, swelling or temporary hearing loss.Because air bags must inflate rapidly and with considerable force, thereis the risk of death or serious injuries such as fractures, facial and eye

    Seating and safety restraints

    69

  • injuries or internal injuries, particularly to occupants who are notproperly restrained or are otherwise out of position at the time of air bagdeployment. Thus, it is extremely important that occupants be properlyrestrained as far away from the air bag module as possible whilemaintaining vehicle control.

    Several air bag system components get hot after inflation. Do nottouch them after inflation.

    If the air bag is inflated, the air bag will not function againand must be replaced immediately . If the air bag is not

    replaced, the unrepaired area will increase the risk of injury in acollision.

    The SRS consists of:

    driver and passenger air bag modules (which include the inflators andair bags),

    one or more impact and safing sensors, a readiness light and tone and the electrical wiring which connects the components.The diagnostic module monitors its own internal circuits and thesupplemental air bag electrical system warning (including the impactsensors), the system wiring, the air bag system readiness light, the airbag back up power and the air bag ignitors.

    Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Air bag readinesssection in the Instrumentation chapter. Routine maintenance of the airbag is not required.

    A difficulty with the system is indicated by one or more of the following:

    The readiness light will eitherflash or stay lit.

    The readiness light will notilluminate immediately afterignition is turned on.

    AIRBAG

    Seating and safety restraints

    70

  • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and light are repaired.

    If any of these things happen, even intermittently, have the SRS servicedat your dealership or by a qualified technician immediately. Unlessserviced, the system may not function properly in the event of acollision.

    Disposal of air bags and air bag equipped vehiclesFor disposal of air bags or air bag equipped vehicles, see your localdealership or qualified technician. Air bags MUST BE disposed of byqualified personnel.

    SAFETY RESTRAINTS FOR CHILDREN

    Important child restraint precautionsYou are required by law to use safety restraints for children in the U.S.and Canada. If small children ride in your vehicle (generally children whoare four years old or younger and who weigh 18 kg [40 lbs] or less), youmust put them in safety seats made especially for children. Check yourlocal and state or provincial laws for specific requirements regarding thesafety of children in your vehicle.

    Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from

    injury in a collision.

    Always follow the instructions and warnings that come with any infant orchild restraint you might use.

    When possible, place children in the rear seat of your vehicle. Accidentstatistics suggest that children are safer when properly restrained in therear seating positions than in the front seating position.

    Children and safety beltsChildren who are too large for child safety seats (as specified by yourchild safety seat manufacturer) should always wear safety belts.

    Follow all the important safety restraint and air bag precautions thatapply to adult passengers in your vehicle.

    If the shoulder belt portion of a combination lap and shoulder belt canbe positioned so it does not cross or rest in front of the childs face or

    Seating and safety restraints

    71

  • neck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit.

    If the shoulder belt cannot be properly positioned:

    move the child to one of the seats with a lap belt only (if equipped) or if the child is the proper size, restrain the child in a safety seat.

    Do not leave children, unreliable adults, or pets unattended inyour vehicle.

    To improve the fit of lap and shoulder belts on children who haveoutgrown child safety seats, Ford recommends use of a belt-positioningbooster seat that is labelled as conforming to all Federal motor vehiclesafety standards. Belt-positioning booster seats raise the child andprovide a shorter, firmer seating cushion that encourages safer seatingposture and better fit of lap and shoulder belts on the child.

    A belt-positioning booster should be used if the shoulder belt rests infront of the childs face or neck, or if the lap belt does not fit snugly onboth thighs, or if the thighs are too short to let the child sit all the wayback on the seat cushion when the lower legs hang over the edge of theseat cushion. You may wish to discuss the special needs of your childwith your pediatrician.

    SAFETY SEATS FOR CHILDREN

    Child and infant or child safety seatsUse a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturers instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the child may be injured in a sudden stop orcollision.

    Seating and safety restraints

    72

  • When installing a child safety seat:

    Use the correct safety belt bucklefor that seating position.

    Make sure the tongue is securelyfastened in the buckle.

    Keep the buckle release buttonpointing up and away from thesafety seat, with the tonguebetween the child seat and therelease button, to preventaccidental unbuckling.

    Place seat back in upright position. Put the safety belt in the automatic locking mode. Refer to Automaticlocking mode.

    Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position which is capableof providing a tether anchorage. For more information on top tetherstraps, refer to Attaching safety seats with tether straps.

    Carefully follow all of the manufacturers instructions includedwith the safety seat you put in your vehicle. If you do not install

    and use the safety seat properly, the child may be injured in a suddenstop or collision.

    1. Position the child safety seat in aseat with a combination lap andshoulder belt.

    Seating and safety restraints

    73

  • Air bag can kill or injure a child in a child seat. If you must use aforward-facing child seat in the front seat, move seat all the way

    back.

    2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.

    3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturers instructions. Be surethe belt webbing is not twisted.

    4. Insert the belt tongue into theproper buckle for that seatingposition until you hear and feel thelatch engage. Make sure the tongueis latched securely by pulling on it.

    PRESS

    Seating and safety restraints

    74

  • 5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt isextracted and a click is heard.

    6. Allow the belt to retract. The belt will click as it retracts to indicate itis in the automatic locking mode.

    7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.

    8. Allow the safety belt to retract toremove any slack in the belt.

    9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make sure the seat issecurely held in place.

    10. Try to pull the belt out of the retractor to make sure the retractor isin the automatic locking mode (you should not be able to pull more beltout). If the retractor is not locked, unbuckle the belt and repeat stepstwo through nine.

    Check to make sure the child seat is properly secured before each use.

    Seating and safety restraints

    75

  • Installing a child safety seat in the center seating position withadjustable lap belt1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbottom is perpendicular to the direction of webbing while sliding thetongue up the webbing.

    2. Place the child safety seat in the center seating position.

    3. Route the tongue and webbing through the child seat according to thechild seat manufacturers instructions.

    4. Insert the belt tongue into the proper buckle for the center seatingposition until you hear a snap and feel it latch. Make sure the tongue issecurely fastened to the buckle by pulling on tongue.

    5. Push down on the child seat while pulling on the loose end of the lapbelt webbing to tighten the belt.

    6. Before placing the child into the child seat, forcibly tilt the child seatfrom side to side and in forward direction to make sure that the seat isheld securely in place. If the child seat moves excessively, repeat steps 5through 6, or properly install the child seat in a different position.

    Attach