metal maChinery solutions Product Catalog · Product Catalog metal maChinery solutions. ... • Max. slit width: ... State-of-the-art in rolling technology, the 4HEL

Product Catalogm e t a l m a C h i n e r y s o l u t i o n s

2 www.eccomachinery.com ECCO Machinery

TennsmiTh

s h e e t m e t a l m a C h i n e r y

TennsmiTh sBs series Folders

SBS12614 SBS15016Bending Capacity (Mild Steel) 10 ga. / 2.0 mm 10 ga. / 2.0 mmBending Capacity (Stainless) 16 ga. / 1.6 mm 20 ga. / 1.0 mmBending Length 126" / 3200 mm 150" / 3810 mmBending Bars 1" / 25 mm and

7/16" / 11 mm1" / 25 mm and 7/16" / 11 mm

Back Gauge Depth (Standard) 41" / 1041 mm 41" / 1041 mm

TennsmiTh heavy Duty hand Brakes

HB48-12 HB73-16 HB97-18 HB97-16 HB97-12Capacity (Mild Steel) 12 ga. / 2.7 mm 16 ga. / 1.6 mm 18 ga. / 1.25 mm 16 ga. / 1.6 mm 12 ga. / 2.7 mmBending Length 49" / 1245 mm 73" / 1854 mm 97" / 2464 mm 97" / 2464 mm 97" / 2464 mmMaximum Lift of Beam 1-7/8" / 47 mm 1-7/8" / 47 mm 1-7/8" / 47 mm 1-7/8" / 47 mm 2-1/4" / 5 7 mmFront to Rear Beam Adjustment 1/2" / 13 mm 1/2" / 13 mm 1/2" / 13 mm 1/2" / 13 mm 1/2" / 13 mmMinimum Reverse Bend 1/4" / 6 mm 1/4" / 6 mm 1/4" / 6 mm 1/4" / 6 mm 1/4" / 6 mmMinimum Flange in Capacity Material 1" / 25 mm 1" / 25 mm 1" / 25 mm 1" / 25 mm 1" / 25 mm

TennsmiTh Power series shears

36A 52A and 52HMax. Shearing Capacity (Mild Steel) 16 ga. / 1.6 mm 16 ga. / 1.6 mmMax. Shearing Capacity (Stainless) 20 ga. / 1.0 mm 20 ga. / 1.0 mmMax. Cutting Length 37" / 940 mm 52-1/4" / 1327 mmBack Gauge Range 30" / 762 mm 30" / 762 mmFront Gauge Range 37" / 940 mm 37" / 940 mm

ECCO Machinery www.eccomachinery.com 3

TennsmiTh (cont’d)


TennsmiTh Powered slip Rolls

SR48PCapacity (Mild Steel) 16 ga. / 1.6 mmMaximum Forming Length 49" / 1244 mmDiameter of Rolls 3" / 76 mmMaximum Forming Radius 1-1/2" / 38 mmWire Grooves 3/8", 1/2", 5/8" / 9.5, 12.7, 15.8 mmGearing Ratio 4:1Roll Speed 22 RPM / 17.28 sfpmMotor 230/640V, 3-phase, 60 Hz, 3/4 HP

Vicon

ViCOn model hVAC 510 Plasma Burning Table • Standard 5' × 10' cutting area with options for up to 6' × 20' cutting area

• From 28 gauge up to 1/2" plate

ViCOn Full Coil Line• 16-28 gauge mild steel capacity• 12,000 lbs maximum coil capacity (with coil drive)• Coil widths from 48" – 60" standard (72" width optional)• Up to six coil stations available

Also Available: Box and Pan Brakes

Ask us about our leasing program (see page 15).



RAms

RAms 2011-C 16 Gauge slitter• 1 HP electric motor, 115/208-230V,

1,725 RPM• Capacity: 24 gauge mild steel• Min. slit width: 3/4"• Max. slit width: 24-3/8"• Approx. speed: 65 FPM

inTRODuCinG: RAms 2051 Plasma TableThis heavy duty RAMS cutting table has an effective 5' × 10' cutting area and is constructed of an all steel welded 3 × 3 tube frame with 10 gauge sides and bottom. It will easily support in excess of 1" mild steel plate.This extremely ridged welded machine weighs in excess of 2,000 pounds and is delivered to your shop in one piece so there is no assembly required. It has dual Browning 3/4" rack and pinion drives along with the finest dual hardened and ground HIWIN #20 linear guideways on both sides of the table, and with dual heavy duty NEMA 34 motors the gantry is automatically squared when you seek the home position – a feature only found on the best machines available. The gantry is strong, ridged, and, being made of aluminum, reduces moving weight and enhances position repeatability.Built in the USA, there is no other machine that offers the same precision, rugged construction or unique features at such an affordable price.This is a turnkey system including the plasma table, plasma cutter, computer, software, training and internet/telephone support to the original owner for the life of the machine.

RAms 24-28 Pittsburgh machine• 1/2 HP electric motor, 115/208-230V, 5.4 AMPS 60 cycle single phase• Capacity: 24 gauge maximum – 28 gauge minimum mild steel• Approx. speed: 35 FPM

RAms 2004 Cleat Bender• Torrington needle bearings• Capacity: 20 gauge mild steel



RAms (cont’d)

RAms-2019 14 ga Power Rotary machine (air operated with a 12 inch throat)• 1/2 HP electric motor, 110-115V single phase

• Full 12" throat depth with no interference

• Capacity: 14 ga maximum

RAms 2014 Auxiliary machine• Capacity: 20 gauge maximum – 26 gauge minimum mild steel

• Approx. speed: 40 FPM

RAms 2006 20 Gauge Pittsburgh machine• 1 HP electric motor, 110-115V single phase

• Torrington needle bearings• Capacity: 20 gauge maximum – 26 gauge minimum mild steel

• Approx. speed: 25 FPM

TeCnA spot Welders

spot Welder AccessoriesElectrodes, electrode holders and resistance welding accessories

TeCnA Rocker Arm spot WelderDual voltage 220V-440V/single phase/60 Hertz output welding transformer



eCCO

eCCO shears• Foot• Air• Hydraulic

eCCO Power Rotary TableShown with optional rotary turning machine

eCCO Box and Pan Brake• 4' – 8' length• Up to 12 gauge mild steel capacity

eCCO V416 straight Leaf Brake

eCCO Plate Rolls


f a b r i C a t i o n m a C h i n e r y

mVD

mVD shearsHydraulic guillotine or swing beam shears ranging from 1/4" × 10' – 3/4" × 20'.• Manufactured in sizes 3 meters to 6 meters and capacities 6 mm to 20 mm

• Back gauge range (stroke ) 1000 mm

mVD Press BrakesFully hydraulic press brakes with downstroking ram. Capacities of 45 tons to 1100 tons and lengths from 4' to 20'.• HAP 35/225-4: 12', 250 Tons• HAP 35/160: 12', 176 Tons• EAP 25-060: 8', 66 Tons/ 3 axis (Y1, Y2, X)

Press Brake Tooling

Press Brake urethane Film4" × 0.015" × 100' 4" × 0.030" × 100' 6" × 0.015" × 100’ 6" × 0.030" × 100' 8" × 0.015" × 100’ 8" × 0.030" × 100'

Made in Turkey with all top quality European components. MVD machines are designed to be reliable, durable, precise, and easy to use.



edwards ironworking machines

edwards e120J5 120 Ton ironworker – Jaws iV• The powerhorse ironworking machine• 5 available stations• Universal open tooling cavity• Electric foot pedal• Electric stroke standard• 24" bar shear

edwards 100 Ton ironworker – Jaws iV• Hydraulic ironworker machine for metal fabrication

• 5 available stations• Universal open tooling station• 24" bar shear

Tooling for ironworkers, metal Working and Portable Fabricating machinesBuffalo, Cleveland Steel Tool, Edwards, Ficep, Geka, Kingsland, Mubea, Peddinghaus, Piranha, Pittsburgh, Scotchman, Spartan, Uni-Hydro, W.A. Whitney, etc.

edwards 55 Ton ironworker – Jaws iV• Best seller• 4 available stations• Universal open tooling station

edwards 65 Ton ironworker – Jaws iV• The most versatile ironworking machine

• 5 available stations• Universal open tooling station• 24" bar shear

edwards 40 Ton ironworker – Jaws iV• 4 available stations• Optional hydraulic accessory package• “Plug and Play” with 10-ton tube/pipe bender

• 20-ton and 40-ton shop press



eCCO ironworking machines

Q35Y-16 Q35Y-25Pressure – Short Ton (Metric Ton) 60

(55)125(110)

Max. Cutting Thickness " (mm) 5/8(16)

1(25)

Plate Strength (N/mm2) ≤450 ≤450Cutting Angle 7° 8°Shearing Size of One Stroke (mm) 16 × 250 / 8 × 400 25 × 330 / 16 × 600Ram Stroke " (mm) 3-1/8 (80) 3-1/8 (80)Number of Strokes (CPM) 8 6Throat Depth " (mm) 11-3/4 (300) 15-3/4 (400)Punching Thickness " (mm) 5/8 (16) 1 (25)Max. Punching Diameter " (mm) 1 (25) 1-3/8 (35)Main Motor Power (kW) 4 7.5Overall Dimensions L × W × H " (mm)

65 × 29 × 70(1640 × 730 × 1770)

93 × 38 × 82(2355 × 960 ×2090)

Weight (kg) 1600 4800

Profile Round Bar Square BarEqual Angle

90° Shearing 45° ShearingSection View

Q35Y-16 1-3/4" (45 mm) Ø 1-1/2" × 1-1/2"(40 mm × 40 mm)

5" × 5" × 1/2"(125 mm × 125 mm × 12 mm)

2" × 2" × 3/16"(50 mm × 50 mm × 5 mm)

Q35Y-25 2-3/8" (60 mm) Ø 2" × 2"(50 mm × 50 mm)

6-1/4" × 6-1/4" × 1/2"(160 mm × 160 mm × 14 mm)

2-3/8" × 2-3/8" × 1/4"(60 mm × 60 mm × 6 mm)

eCCO hY-4-1 hydraulic notcher• 4 mm mild steel capacity (50,000 psi tensile strength)

• 700 mm × 800 mm table• 220 mm × 220 mm × 90° notch• 32 Strokes per minute• 3 HP Hydraulic system drive motor• Approximately 550 kg• CSA Electrics and wires

eCCO notchers

Faccin 4heL 4 Rolls Plate Bending RollsState-of-the-art in rolling technology, the 4HEL is considered the most versatile, precise, and easy to use plate roll.

Faccin Rolls



Boschert notchers

Boschert LiTe hydraulic Power notcher• 5/32" mild steel capacity• 10 gauge stainless steel capacity• 8-7/8" × 8-7/8" 90° notch• 35" wide by 25" deep table with milled surface

• 4.5 HP motor

Boschert VARi iV hydraulic Variable Angle notcher • 5/32" mild steel* capacity – * mild steel designated as 50,000 psi

• 11 gauge stainless steel** capacity• 5.9" × 5.9" notch• 39.4" wide by 25.6" deep table• 6.5 HP drive motor** Stainless designated as 75,000 psi

Boschert eagle and eagle 250 hydraulic Power notcher• 1/4" mild steel capacity• 3/16" stainless steel capacity• 8-7/8" × 8-7/8" 90° notch• 35" wide by 25" deep table with milled surface

• 6.5 HP motor

RDB-250 Tube and Pipe BenderWith 220 volt single phase power the RDB-250 can bend up to 2-1/2" tubing and 2" Schedule 40 pipe. It can bend to 180° in 9 seconds and can be programmed to bend up to 360° both left and right – great for solid rod applications when teamed up with a universal bend plate. It makes quick work of complex serpentine bends because of its unique quick release counter die mount and easy to use touch screen controller. Controller features an internal memory that can hold 170 programs with 10 bends per program, and accepts a memory card for unlimited program storage. Unit can also be used in manual mode for one-off prototypes, and will accept an index table – important for keeping a section of bends during a program on the correct plane to achieve the most accurate finished product possible.

• Minimum CLR – .5"• Minimum OD – .25"• Mild Steel Solid Rod – 1.25"• Mild Steel Pipe Schedule 40 – 2"• Mild Steel Round Tube Wall – 2.5"• Mild Steel Square Tube (Wall) – 2" • Stainless Steel Pipe Schedule 40 – 1.5"

• Stainless Steel Round Tube Wall – 2.375"• Chromolly Round Tube Wall – 2"• Aluminum Round Tube Wall – 2.5"• Maximum Center Line Radius Clr – 9"• Power – 220V Single Phase• Shipping Weight – 610 Lbs• Shipping Dimensions – 40" × 32" × 43"

Baileigh Tube and Pipe Benders


eCCO sawseCCO model ue-916V-CsA horizontal Band saw

• Capacity round – 8.85" at 90°• Capacity round – 6.5" at 45°• Capacity square – 8.85" at 90°• Capacity square – 6.5" at 45°• Capacity rectangular – 8.86" × 13.5" at 90°

• Capacity rectangular – 8.86" × 6.5" at 45°

• Blade size – 1" × .035" × 119.48"• Variable blade speed – 82-259 FPM

• Blade guide – roller

• Miter angle – 0-45°• Miter adjustment – vice• Descent Control – hydraulic• Return – manual• Motor – 1.5 HP• Electrics – 220V, single phase

eCCO model KB-36 Vertical Band saw• Throat depth – 14"• Work height – 9-1/16"• Table size – 19-1/2" × 15-1/4"• Table inclination (4 ways) – 15"• Saw blade length – 111-13/16"• Saw blade width – 3/16"• Saw blade speeds – 65-295• Butt welder capacity – 1/8" × 5/8"• Drive motor – 1 HP

eCCO model Cs350 manual Cold Cut saw with Variable speed• Variable speed control

24-120 RPM• Electrics 3 HP 220V 3 phase 60 Hz motor

• Mitre design for cutting angle adjustment 45° on the right and left respectively

eCCO model W1318s horizontal Band saw• Blade Motor – 3 HP• Coolant Motor – 1/8 HP• Electrics; 220 volt 3 phase 60 Hz• CSA approved• Knock down feed table• Complete with industrial level coolant pump for longer life

• Coolant tank: 30 liter• Quick action vise• Fixed vise jaw has a grooved surface for camping work piece securely

• Length stopper is a standard accessory• Blade tension adjusting gauge• Blade size – 1.06" × 0.035" × 162.6"• Blade speeds – 92/137/198/256 FPM• Shipping Dimensions – 83" × 37" × 62.8"• Weight: N.W / G.W 1870 lbs / 2134 lbs

Capacities:• Rounds at 90 degrees – 13"• Rectangular at 90 degrees – 13" × 18"• Rounds at 45 degrees – 11"• Rectangular at 45 degrees – 13" × 11"• Rounds at 60 degrees – 6.3"• Rectangular at 60 degrees – 10" × 6.3"



C h i P m a k i n g m a C h i n e r y

eCCO mills, Lathes, and Drill PresseseCCO model 3Vm Ram Turret Vertical milling machine c/w Variable speed• Single phase electrics• Table size: 10" × 54"• Quill travel: 5"• Variable speeds 70 – 4200 RPM• Main motor 3 HP, 220 volt 1 phase

eCCO model Ys2Vs-DRO-1 single Phase Vertical Turret mill• Table size 9" × 49" • Quill travel: 5"• Variable speeds 70 – 4200 RPM• Main motor 3HP, 220 volt 1 phase

eCCO model 4KVs-nT40 milling machine• X-axis dovetail and Y- and Z-axis square sideways (box way)

• Table size: 10" × 54" • Quill diameter: 100 mm• Spindle taper: NT 40 • Variable speeds: 70 – 4200 RPM • Main motor: 5 HP, 220 volt 3 phase

eCCO model mD930 mill Drill

eCCO model DP-925GAD inverter Drill Press

eCCO model KD-1440 Lathe• Swing over bed – 14"• Distance between centers – 40"

eCCO model Gh-1660ZX c/w DRO• Swing over bed – 16"• Distance between centers – 60"

eCCO model Gh-1860ZX-DRO Precision Lathe• Swing over bed – 18"• Distance between centers – 60"

eCCO model Gh-1880ZX-DRO Precision Lathe• Swing over bed – 18"• Distance between centers – 80"


w a t e r j e t C u t t i n g

semyx Waterjet Cutters

scorpion series – model 318The most versatile waterjet cutting system on the market when it comes to speed and accuracy, the Scorpion waterjet cutting system is efficient both in size and price.• Easy loading from all three sides• Rigid bridge gantry• Extreme accuracy provided by ball screws• Small Footprint – Width: 141" / Length: 159"• X-Axis Cutting Stroke: 120" / Y-Axis Cutting Stroke: 72"• Z-Axis Stroke: 7"• Accuracy: 0.003"• Drivers: AC Servo Motors• Motion for X-Axis: Ball Screw / Motion for Y-Axis: Ball Screw

Optima seriesProvides a vigorous industrial design and rigid construction that combines precision and simplicity, the Optima model is made to handle high production for versatile applications.• Separate waterjet tank allows for extra weight on the tank• Roller bearings guarantee the longest life possible• Special sides stationary covers• Combination of precision and simplicity• Z-Axis Stroke: 7"• Drivers: AC Servo Motors• Motion for X-Axis: Ball Screw / Motion for Y-Axis: Ball Screw

OPTiMA MODELCuTTiNG STROkE (") FOOTPRiNT (")

ACCuRACY (")X-AXiS Y-AXiS FRONT SiDE210 80 40 120 63 0.006240 80 156 132 189 0.006260 80 240 132 268 0.006320 120 78 178 111 0.004340 120 156 178 189 0.004360 120 240 178 325 0.006420 160 78 222.5 189 0.004460 160 240 222.5 325 0.004

Series

Series


l a s e r C u t t i n g

han-Kwang Laser Cutting machines

• Synchronized dual servo motor gantry• Durable rack and pinion motion system• Adaptive optics AFC unit• Quick change lens cartridge• Rigid heavy-duty body frame• Built-in air filtration and dryer system• Automatic dual shuttle table

• Zone and ducting exhaust system• Automatic nozzle cleaning system• Aiming diode laser• Cross-jet oil mist spray system• Dynamic power/speed ramping• Edge detection and axis re-alignment• High-speed etching mode

• Quick Micro-tap and Micro-welding• Pre-piercing mode• Multi Pulse Piercing (MPP)• Pro-Design nesting software• Plasma Monitoring Unit (PMU) option• Lens Crack Sensor (LCS) option

FL 3015 – Design, Features and Functions

• 2KW fiber laser resonator (higher powers available as an option)

• Siemens 840D SINUMERIK control• Quick change non-contact cutting head• Rapid traverse speed 6700 IPM with 1.5G acceleration

• 15" flat panel touch screen• 512MB memory with 40GB HDD

• Cutting feed rate up to 1000 IPM• Lens protective glass• Open / close roof design• Automatic regulator systems for three (3) assist gases

• 70% energy savings by fiber laser compared to CO2 laser

• No need for laser gas

• Cuts thin materials 2-3 times faster than CO2 laser systems

• No need for optical mirrors to deliver the laser beam to the cutting head

• Cuts exotic materials including copper and brass

• Simple and modular fiber laser source

Fs 3015 Fiber – Design, Features and Functions

HAN-KWANG has produced approximately 1000 systems over 18 years and continues to develop customer-oriented solutions specially designed to meet the challenge of today’s competitive industrial environment. Its technical and demo center, HAN-KWANG USA, is located in Chicago, Illinois, where there are two laser cutting systems running for demonstration and a huge service parts inventory. They have another service depot in Charlotte, North Carolina, where one laser cutting system is running for demonstration and training. With more than 15 sales networks throughout the United States, Canada and Mexico and a well-established quick-response service system, HAN-KWANG provides top quality service and support to all its customers to ensure their complete satisfaction.

ECCO Machinery www.eccomachinery.com 15ECCO Machinery www.eccomachinery.com 15

eCCO Lease Financing ProgramECCO Machinery and National Leasing have developed a strategic partnership to bring you the best equipment financing solutions in the industry.The wise use of lease financing is the cornerstone of growth for most enterprises. Why should leasing be considered as a financing solution for acquiring equipment? Because of the many benefits it offers:

1. Tax managementa) The ECCO Lease Financing Program can provide the

ability to write the fixed lease payments off as a business expense and may reduce the amount of tax payable.

b) If assets are acquired through Cash Flow or Finance Loan then CCA allowances will apply, resulting in a longer depreciation period.

2. Asset managementa) The ECCO Lease Financing Program will provide the

opportunity to rollover equipment during or at the end of the lease term in order to keep equipment current and systems and people productive.

b) The program provides a better tool for business asset management by offering four options at the end of the lease term:

i) Return the equipment and upgrade to new equipment

ii) Trade up the equipment at any time during the lease or at the end of the lease term

iii) Buy out the equipment and obtain additional equipment

iv) Monthly renewal

3. Cash Flow managementa) The ECCO Lease Financing Program has fixed monthly

lease payments to conserve cash flow dollars today to reinvest back into the business and generate profits from the revenue.

b) The program provides 100% financing – just first and last payments in advance.

4. soft Cost AllowancesEach lease can include soft cost components such as asset extended warranty and maintenance, software and consulting, training and development, installation and delivery, customs/brokerage and duty fees, etc.

For more information contact:

Candice Dowhaniuk Account Manager, National Leasing780-448-9353 / 877-363-4223 780-461-4039 / 877-871-1589

[email protected]

ECCO Machinery – a single source for all of your machinery requirements throughout Canada, the US and internationally. We offer an expansive line of new, used, and custom built machinery, as well as providing control and automation upgrades to existing equipment. We service what we sell and we are pleased to offer comprehensive maintenance programs to keep all of your machinery operating smoothly and efficiently.

ECCO Machinery’s Mechanical Design Engineers, Machinists, and Service and Sales personnel are highly professional, technically trained, and have many years of industry knowledge and experience. From the time of inquiry and order placement, through to final delivery, installation and set-up of your equipment, our ECCO Machinery team will attend to every detail necessary in order to ensure your utmost satisfaction.

useD maChineryWe have access to used machinery and machine tools locally and from around the world, and we constantly add to our inventory. If you require a specific machine or tool please call or email us with your specifications and applications and we will find the machine for you.

serViCe anD maintenanCeWe provide service and maintenance for all your machinery needs. Our knowledge and experience can provide you with a reliable solution, whether you need machinery rebuilt or on-site service and repairs to retrofit your existing machinery.

About eCCO machinery

m e t a l m a C h i n e r y s o l u t i o n seCCo machinery

#101 – 19335 96th Avenue, Surrey, BC V4N 4C4Phone: 778-298-2023 • Fax: 778-298-2024

Toll Free: 1-877-513-1773 • www.eccomachinery.com PB20

1 09

13

Documents

metal maChinery solutions Product Catalog · Product Catalog metal maChinery solutions. ... • Max. slit width: ... State-of-the-art in rolling technology, the 4HEL