Embed Size (px)
Citation preview
Model 104 Slider Belt Conveyor
Model Description: The Model 104 Slider Bed Belt is designed with the systems approach in mind. The square head and tail end terminals allow you the flexibility to combine this unit with other Titan units to assure a continuous flow of material. The standard 4" deep formed 12-gauge frame allows integration with several other types of conveyors available from Titan. Screw type take-ups and 4" diameter crown face pulleys are some of the standard design features. Modular design allows you the flexibility to add additional sections if required. Your material handling requirements can be solved by the experts at Titan.
1
MODEL 680MULTI-STRAND CHAIN CONVEYOR
The Model 680 Multi strand chain conveyor is used to convey products that are not conveyable on a standard roller conveyor. The standard chain is C2060 double pitch with a load capac-ity of 2,400 lbs. An optional C2080 double pitch chain can be used for loads up to 4,000 lbs. Optional low profile side mounted drive and addi-tional strands of chain can be added to increase load capacities.
NOTE: Specifications subject to change without notice
MODEL 680 MULTI-STRAND CHAIN CONVEYORStandard Options
Chain (2) strands of C2060 C2080, multiple strands availableCapacity 2,400 lbs 4,000 with (2) strands C2080Drive 1 HP 230/460/3/60 Horsepower to fit applicationFrame Formed 7 ga. StructuralChain Speed 30 F.P.M. Specify
OptionalDrive location, HP, speed, variable speed available, controls, multiple chain strands, paint
MODEL 680 MULTI-STRAND CHAIN CONVEYOR
BELT WIDTH + 9 3/8"
INFEED SECTION
SECTION A-A SECTION B-B
5 3 4" 812"
BELT WIDTH 3 3 8"C - C 6"
14" 18"DRIVE SECTION
OVERALL LENGTH
1 1332"
8 12"
9 9 32"
20" MINIMUMW/BOTTOM
MOUNT DRIVESTD. IC60REDUCER
A
A B
B
MODEL 535CHAIN DRIVEN LIVE ROLLER
CONVEYOR
The ultimate in heavy-duty conveying for pallets, skids or drums - the Model 535 is designed to handle extremely heavy loads. The 3 1/2” diameter x .300 wall (schedule 80 pipe) rollers are rated for 2500 lbs. per roller. The rollers use a heavy-duty industrial, grease sealed, 1 1/16” hex bore bearing. The Model 535 is available with either #60 or #80 roll-to-roll chain drives depending on chain pull required. Standard construction is a 6” at #8.2 structural channel frame. This unit is available with either a bottom mount or side mount drive. Supports are structural channel (non-adjustable) with foot pads. Roller centers are 6” for #60 chain drive and 6 1/2” for #80 chain drive.
NOTE: Specifications subject to change without notice
MODEL 535 CHAIN DRIVEN LIVE ROLLER CONVEYORSTANDARD OPTIONS
Effective Widths 15” to 66” Customer can specifyLengths Per application - 5’ Minimum 3’ minimum, maximum length based on applicationRoller Size 3 1/2” dia. x .300 wall 1-1/16” hex shaft
(#2500 roll rating)Roller Centers 6” Roller centers of 6”, 9”, 10-1/8”, 12” with #60 sprockets,
#80 roll-to-roll chain drive with roller centers of 6-7/16”, 9-7/16”, 12-7/16”
Frame Structural channelDrive 3/4 H.P. 230/460/3/60 1, 1-1/2, 2, 3, 5 HP, 115/230/1/60, 575/3/60, severe duty,
inverter duty, brake motorChain Drive #60 #80
OPTIONALRoller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless con-struction, H. P. , Speeds, Variable speed, Controls, Paint, 2 or 3 strand chain transfers, Pallet lifts, “C” Face brake and Fixed end stop, Rollers set low, UHMW sleeves, Galvanized rollers, accumulation sleeves, Knee braces, Air operated
blade stop, Supports - 6” @ #8.2 structural channel, Pop-up roller, blade stops, pallet lifts.
MODEL 535CHAIN DRIVEN LIVE ROLLER CONVEYOR
IC-70
IC-70
STANDARD 10' LG. CONVEYOR SECTION W/#60 CHAIN DRIVE
ROLLERS SET HIGH
STANDARD BOTTOM MOUNT DRIVE
13"
ROLLERS SET LOW
STANDARD SIDE MOUNT DRIVE
STANDARD 9'-9" LG. CONVEYOR SECTION W/#80 CHAIN DRIVE
ROLLERS SET HIGH
STANDARD BOTTOM MOUNT DRIVE
ROLLERS SET LOW
STANDARD SIDE MOUNT DRIVE
10'6" STANDARD CENTERS
30"STANDARD
3/8"
1 29/32"
8 1/2"
6 15/16"EFFECTIVEWIDTH
8 1/2"
2 1/8" 2 1/8" 5 1/4"
60A20 SPROCKETS
C6 x #8.2 CHANNEL
23"
14"
19 1/2"
9'- 9"6 1/2" STANDARD CENTERS
30"STANDARD
3/8"
1 29/32" EFFECTIVEWIDTH 7 1/4"
8 1/4"
80A16 SPROCKETS
1 5/8" 1 7/8"C8 x #11.5 CHANNEL
14"
22 3/4"
C6 x #8.2 CHANNEL
20 7/8"
12 15/16"
OPTIONAL ROLLER CENTERS5 5/8" CENTERS6 3/8" CENTERS6 3/4" CENTERS7 1/8" CENTERS
OPTIONAL ROLLER CENTERS7" CENTERS
7 1/2" CENTERS8" CENTERS
8 1/2" CENTERS
[Type here]
Turn Table On Shuttle
Model Description: When your plant layout requires a directional change in the smallest possible space of your conveyor system, you should consider using a Titan Powered Turntable. The turntable conveyor can be used for product sortation, accumulation as well as directional changes. The Titan Turntable is available in sizes ranging from 2' diameter to 12' diameter. The standard table top is 7-gauge construction with angle iron supports. The top is driven by either chain and sprockets or air operated cylinder. The unit is furnished with expanded metal guards on all four sides. The unit can be supplied with chain and sprocket drive, air operated for 90 degrees’ rotation or no drive for manual indexing. Tops can be fitted with gravity roller or chain driven live roller conveyor to suit your application.
3
[Type here]
Model 425
Model 425 Gravity Roller Conveyor Specifications:
Axle: 11/16" Hex
Capacity: 580 lbs
Frame: Formed 7 gauge
Minimum Centers: 3"
Roller Rating: 625 lbs.
Rollers: 2-1/2" Diameter x 11 Gauge
Shaft: 11/16" hex
4
[Type here]
525 V-Belt
Model MDR Poly V-Belt Motor Driven Roller Conveyor Specifications:
Bearings: Grease Sealed
Chain: #50 Roll-to-Roll Drive
Drive: 24 Volt DC
Frame: Formed 7 Gauge
Paint: One Coat Industrial Enamel
Rollers: 2-1/2" dia. x 11ga. or 2-5/8" dia. x 7 ga. or 1.9" dia. x 16 ga./Spring Loaded 7/16" Hex Shaft
Speed: Specify
Supports: "H" Type
5
[Type here]
525 CDLR W/ Iron Cross 525 CDLR
Model Description: The Model 525 is designed to handle heavy loads including skids, drums, and pallets. This unit incorporates a number 50 chain with a roll-to-roll drive. The frame is a heavy formed 7 gauge construction with a one piece chain guard. Rollers are 2-1/2" diameter x 11 gauge (580 lb. capacity) centers are 2-13/16", 3-7/16", 4-3/8", 5", 5-15/16" and 10".
Standard floor supports supplied are adjustable for approximately 30" to the top of roller. This model is available in lengths to meet your needs (min length: 4-1/2"). Consult the factory for further details.
6
MODEL 525CHAIN DRIVEN LIVE ROLLER
The Model 525 Chain Driven Live Roller conveyor from RSI, Inc. is designed to handle heavy loads such as pallets, skids or drums. The unit incorporates a number 50 chain with a roll-to-roll drive. The frame is a heavy formed 7 gauge construction with a one piece chain guard. Rollers are 2-1/2” diameter x 11 gauge (580 lb. capacity). The standard drive is a 3/4 H.P. for 30 F.P.M. roller speed. A wide range of standard effective widths are available. Standard roller spacings are 2-13/16”, 3-7/16”, 4-3/8”, 5”, and 5-15/16”. Floor supports are optional. The Model 525 comes in lengths to suit with a minimum length of 4’ long. Consult the factory for further details.
NOTE: Specifications subject to change without notice
MODEL 525 CHAIN DRIVEN LIVE ROLLER CONVEYOR SPECIFICATIONSStandard Options
Effective Widths 13” to 40” Specify up to 40” E.W.Lengths 5’ min. 3’ min., max. based on application
Roller Size 2 1/2” Dia. x 11 ga. with 11/16” hex shaft - 580 lb. roller cap.
Roller Center 5” 2-13/16”, 3-7/16”, 4-3/8”, 5-15/16”, 10”Frame Formed 7 ga.
Drive 3/4 H.P. 230/460/3/60 1, 1-1/2, 2, 3 H.P. 230/460/3/60, severe duty, inverter duty, brake motor
Chain Drive #50 #60 availableOPTIONAL
Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P. , Speeds, Variable speed, Controls, Coated rollers, Paint, 2 or 3 strand chain transfers, Pallet lifts,
Pallet jack plates for side or end load, “C” Face brake and Fixed end stop, Rollers set low, UHMW sleeves, Accumula-tion sleeves, Knee braces, Air operated blade stop, Supports - 6” @ #8.2 structural channel,
MODEL 525CHAIN DRIVEN LIVE ROLLER CONVEYOR
EFFECTIVE WIDTH
5 5/16"
1 1/2"
3/8"1 11/16"
3 1/2"
5 13/16" 5 13/16"1 11/16"
5 5/16" EFFECTIVE WIDTH 1 1/2"
1"18 13/16"
11 1/2"
15 13/16"
8"
6 1/2"8 5/16"
5 13/16"1 11/16"
5 5/16"EFFECTIVE WIDTH3 1/2"
5 13/16"1 11/16"
13"
OVERALL LENGTH
ROLLERS SET LOW ROLLERS SET HIGH
FIGURE "B" FIGURE "C"
STANDARD BOTTOM MOUNT DRIVE
FIGURE "D"
FIGURE "E"
STANDARD SIDE MOUNT DRIVE
FIGURE "A"
DOUBLE WIDE CHAIN GUARD(STANDARD CENTERS - 3 7/16")
FIGURE "F"
DOUBLE DRIVE GUARD(STANDARD CENTERS - 2 13/16")
FIGURE "G"
18 3/8" (IC-60)19 1/2" (IC-70)20 7/8" (IC-80)REDUCERS
OPTIONALSUPPORTS
[Type here]
45 Degree Plastic Belt
The Series 2100 Flat Top Zero Tangent Radius belt is designed specifically for curved conveyance, free of straight sections, maximizing all available space. The S2100 has a smooth, closed-top surface that can handle a variety of package sizes, types, and configurations, and is able to maintain product orientation and spacing through its curves. Its compact design provides flexibility, simplifying layout design and conveyor installation. • Patent-pending, symmetric drive design simplifies installation • Lug-tooth style sprockets and positive drive system provide improved reliability and durability • Modular belt construction reduces maintenance time and cost Contact Intralox today for a sample of this new product or for more information.
7
POWER TURNTABLE
POWERED TURNTABLE SPECIFICATIONS
DRIVE:...................................................................................................................1/2 H.P. 230/460/3/60SPEED: .......................................................................................................... 2.5 R.P.M. at Outside RimFRAME: ............................................................................................. 7 Gauge Top with Angle Iron BaseBEARINGS: ..................................................................................................................... Grease SealedSUPPORTS: ........................................................................................................ Fixed for 30” ElevationPAINT: .......................................................................................................... One Coat Industrial Enamel
When your plant layout requires a directional change in the smallest possible space, you should consider using a RSI Powered Turntable. The turntable can be used for product sortation, accumulation as well as directional changes. The RSI Turntable is available in sizes ranging from 2’ diameter to 10’ diameter. The standard table top is 7 gauge construction with angle iron supports. The top is driven by either chain and sprockets or a contact wheel. The unit is furnished with expanded metal guards on all four sides. Roller supports supplied as optional equipment. The unit can be supplied with chain and sprocket drive, air operated for 900 rotation or no drive for manual indexing. Tops can be fitted with gravity roller or chain driven live roller conveyor to suit your application
NOTE: Specifications subject to change without notice
POP-UP TRANSFER, POP-UP STOPS, PALLET CENTERING, PALLET LIFT and PALLET CROWDER OPTIONS
Designed to handle heavy duty loads such as pallets, skids and drums. Heavy duty construc-tion with #50 toll-to-roll drive chain. (#60 chain op-tional.) Standard rollers are 2 1/2” diameter x #11 gauge or 2 5/8” diameter x #7 gauge. Standard roller centers are 5”. Supports are 4” structural with adjustable feet.
NOTE: Specifications subject to change without notice
MODEL 525 CHAIN DRIVEN LIVE ROLLER CONVEYOR SPECIFICATIONSStandard Options
Effective Widths 13” to 40” Specify up to 72” E.W.Lengths 5’ min. 3’ min., max. based on applicationRoller Size 2” Dia. x 11 ga. with 7/16” hex shaft - 580 lb. roller cap.Roller Center 5” 2-13/16”, 3-7/16”, 4-3/8”, 5-15/16”, 10”Frame Formed 7 ga. 6” C structural
Drive 3/4 H.P. 230/460/3/60 1, 1-1/2, 2, 3 H.P. 230/460/3/60, severe duty, inverter duty, brake motor
Chain Drive #50 roll to roll drive #60 availableOPTIONAL
Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P. , Speeds, Variable speed, Controls, Coated rollers, Paint, multi-strand chain transfers, Pallet lifts, Pal-
let jack plates for side or end load, “C” Face brake and Fixed end stop, Rollers set low, UHMW sleeves, Accumulation sleeves, Knee braces, Air operated blade stop, Supports - 6” @ #8.2 structural channel,
POP-UP TRANSFER, POP-UP STOPS, PALLET CENTERING, PALLET LIFT and PALLET CROWDER OPTIONS
18"21 15/16"
3 3/4"
14"
3 1/2"
Overall Length
30"Standard
Effective Width
End ViewNOTE: Pop-up Travel Chain Approximately 34" above roller
4 1/8"
13 3/4"34 1/2"
3/8"
1 11/16"
EffectiveWidth1 1/2" 3 1/2"
1 13/16"
1"18 13/16" 17 1/8"
Rollers Set High
18"21 15/16"
3 3/4"
14"
3 1/2"
Overall Length
30"Standard
Effective Width
End ViewNOTE: Pop-up Travel Chain Approximately 34" above roller
4 1/8"
13 3/4"
8"
Standard Side Mount Drive
34 1/2"
3/8"
1 11/16"
EffectiveWidth1 1/2" 3 1/2"
1 13/16"
1"18 13/16" 17 1/8"
Standard Bottom Mount Drive
Rollers Set High
Chain Driven Live Roller Conveyorwith Pop-Up Pallet Lift
Chain Driven Live Roller Conveyor with Pallet Centering device - Pallet Crowder also available
POWERED TURNTABLE
Rotation
Optional Roller Approaches
20" Min.Expanded Metal GuardingFour Sides
6"Dia.
Optional SiderailsSpecify Height Required
