Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.

MORTISE LOCKINSTALLATION INSTRUCTIONS

MUSEO DESIGNER TRIMFM 601 (617418015)

Rev. C (04/13)

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.

TABLE OF CONTENTS:DOOR PREPARATION

LOCK HANDING

FULL WORKING TRIM

HALF WORKING TRIM

FULL DUMMY TRIM

HALF DUMMY TRIM

SECONDARY TRIM ATTACHMENTEMERGENCY KEY PLATE

1

2

3

8

12

16

SECTIONALR & L ESCUTCHEON

SECTIONALR & L ESCUTCHEON

SECTIONALR & L ESCUTCHEON

SECTIONALR & L ESCUTCHEON

6

10

13

1415

LOCK HANDING IS CRITICAL TO ENSURE LOCK FUNCTIONS PROPERLY

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.1

DOOR PREPARATION:

FULL WORKING TRIM:LOCK-BODY PREPSECTIONALR & L ESCUTCHEON

HALF WORKING TRIM:LOCK-BODY PREPSECTIONALR & L ESCUTCHEON

FULL DUMMY TRIM:SECTIONALR & L ESCUTCHEON

HALF DUMMY TRIM:SECTIONALR & L ESCUTCHEON

T31046NO ADDITIONAL PREP REQUIRED BEYOND T31046

T31047

T31162

T31164

T31163T30651

T31163T30652

ALL WORKING TRIM MUST FIRST BE PREPARED FOR THE LOCK-BODY THEN FOR THE TRIM

TEMPLATE

NO ADDITIONAL PREP REQUIRED BEYOND T31162

ALL TEMPLATES CAN BE FOUND ATWWW.CORBINRUSSWIN.COM

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.2

Mortise Lock Handing Instructions

RED Locking Screw

Step 1) Move the Red locking screw to side of lock-body being locked (Fig. 1)

Step 2) Push in latch then depress catch plate with screw driver (Fig. 1)

Catch Plate

Step 3) Pull latch out of lock-body and turn latch over (Fig. 2)

Figure 1

Figure 2

Figure 3

Step 4) Push in latch while holding screw driver behind latch tail (Fig. 3)

Note: Push in latch until catch plate is no longer depressed (Fig. 4)

Figure 5

Step 5) Rotate lock front to match bevel of door as shown (Fig. 5)

MAKE SURE CATCH PLATE IS EVEN W/ TOP SURFACE

GOOD BADFigure 4

WARNING: LOCK-IN CAN

OCCUR IF LATCH IS NOT PROPERLY

INSTALLED

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.3

FULL WORKING TRIM INSTALLATION

Step 1) Install strike with shorter (3/4”) mounting screws

Step 2) Insert mortise lock into door and hand tighten longer (1”) mounting screws

SECTIONAL:

Step 3) Thread adapter plate hub into lever and fully tighten

Step 4) Align adapter plate hub with square hole in lever; keeping hub as tight as possible

MAKE SURE LOCK IS UNLOCKED

Step 5) Install O/S trim assembly

NOTE: Spindle can be used to help thread hub into lever

Adapter Plate Hub

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.4

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

GOODBAD

Step 6) Install I/S adapter plate

Set screw hole in hub faces away from lock edge

Align studs on rose with bushings in adapter plate

Step 7) Install I/S spindle and rose

Step 8) Install I/S lever with set screw

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.5

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

Step 10) Mark turn-piece mounting holes and drill two .110” (BIT #35) holes where marked

Step 11) Mount turn-piece

Step 9) Install cylinder and secure with set screw

Slightly retract key to help thread cylinder into lock-body

AFTER INSTALLING CYLINDER FULLY TIGHTEN LOCK MOUNTING SCREWS

CYLINDER SET SCREW

Step 12) Install scalp

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.6

Step 1) Install strike with shorter (3/4”) mounting screws

Step 2) Insert mortise lock into door and hand tighten longer (1”) mounting screws

R & L ESCUTCHEON:

MAKE SURE LOCK IS UNLOCKED

NOTE: Repeat step 3 & 4 for I/S Escutcheon

Step 5) Install O/S trim assembly

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

GOODBAD

Step 3) Thread hub into lever and fully tighten

Step 4) Align hub with square hole in lever; keeping hub as tight as possible

Hub

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.7

Align Turn-Piece Vertically

Step 6) Install I/S Escutcheon

CYLINDER SET SCREW

Step 7) Install Cylinder

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

GOODBAD

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

AFTER INSTALLING CYLINDER FULLY TIGHTEN LOCK MOUNTING SCREWS

Step 8) Install Scalp

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.8

HALF WORKING TRIM INSTALLATION

Step 1) Install strike with shorter (3/4”) mounting screws

Step 2) Insert mortise lock into door and hand tighten longer (1”) mounting screws

MAKE SURE LOCK IS UNLOCKED

SECTIONAL:

Align studs on rose with bushings in adapter plate

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

GOODBAD

Step 3) Install I/S adapter plate Step 4) Install spindle and rose

Step 5) Install I/S lever with set screw

Half trim adapter plate must be on non-trim side of the lockbody

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.9

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

Step 6) Install cylinder and secure with set screw

Slightly retract key to help thread cylinder into lock-body

AFTER INSTALLING CYLINDER FULLY TIGHTEN LOCK MOUNTING SCREWS

CYLINDER SET SCREW

Step 7) Mark turn-piece mounting holes and drill two .110” (BIT #35) holes where marked

Step 8) Mount turn-pieceStep 9) Install scalp

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.10

R & L ESCUTCHEON:Step 1) Install strike with shorter (3/4”) mounting screws

Step 2) Insert mortise lock into door and hand tighten longer (1”) mounting screws

MAKE SURE LOCK IS UNLOCKED

Step 5) Install I/S Escutcheon

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

GOODBAD

Align Turn-Piece Vertically

Step 3) Thread hub into lever and fully tighten

Step 4) Align hub with square hole in lever; keeping hub as tight as possible

Hub

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.11

4

6

Spindles

Keypad ribbon cable

Outsideof Door

Installation of Outside Escutcheon

2A. For fire rated doors feed ribbon cable connector and ground wire from outside escutcheon through the fire stop plate.

2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through weather seal gasket (if used), then conduit sleeve in door (not shown).

3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lockbody make certain the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 Allen wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder. Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly. Tighten (2) #12 x 1" lockbody screws. Remove Allen wrench.

Installation Instructions

Groundwire

Gasket (optional)

C A U T I O NDOOR MUST REMAIN OPEN

DURING INSTALLATION.USE DOOR STOP.

NOTE: Key and cylinder must be rotated as shown

Correct Incorrect

Use Correct Spindle Orientation

STANDARD MUSÉO

GASKET APPLICATION:Peel off the adhesive protective paper from gasket. Feed Trim assembly motor harness through gasket opening as shown and firmly press gasket to escutcheon, aligning edge of gasket with the edge of the escutcheon.

1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a device is ordered. this kit includes gaskets and a conduit. When ordering the kit separately, order part number 794F929. The gaskets may be used as a seal between the escutcheon and the door surfaces.

NOTE A.For MUSÉO Lever collections ONLY.Rotate adapter bushing as neededto insure horizontal lever position and maximum thread engaging lever - adapter bushing.

LeverLever

Step 6) Install cylinder and secure with set screw

Slightly retract key to help thread cylinder into lock-body

AFTER INSTALLING CYLINDER FULLY TIGHTEN LOCK MOUNTING SCREWS

CYLINDER SET SCREW

Step 7) Install scalp

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.12

FULL DUMMY TRIM INSTALLATION

SECTIONAL:

Step 1) Install O/S adapter plate Step 2) Install I/S adapter plate

Step 3) Install rose onto both adapter plates

Align studs on rose with bushings in adapter plate

Step 4) Install both levers with set screw

INSTALLATION INSTRUCTIONS

MUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.13

R & L ESCUTCHEON:

Step 3) Install O/S Escutcheon Step 4) Install I/S Escutcheon

Step 1) Insert spindle into hub and rotate lever CW until tight

Step 2) Push spindle into lever

NOTE: Repeat step 1 & 2 for I/S Escutcheon

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.14

HALF DUMMY TRIM INSTALLATIONSECTIONAL:

Step 1) Install adapter platePlastic bushings in

adapter plate go on top

Step 2) Install mounting screws and washers

Step 3) Install rose onto adapter plate

Step 4) Install lever with set screw

Align studs on rose with bushings in adapter plate

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.15

R & L ESCUTCHEON:

NOTE: Re-hand the lever, if necessary, by pushing spindle out of dummy plate and rotating lever

Step 1) Hold O/S escutcheon on door Step 2) Install mounting screws and washers

INSTALLATION INSTRUCTIONSMUSEO Trim InstructionsFM 601 Rev. C (04/13) (617418015)

Copyright © 2013 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.16

SECONDARY TRIM INSTALLATION

EMERGENCY KEY PLATE:Step 1) Mark emergency key mounting holes and drill two .110” (BIT #35) holes where marked

Step 2) Mount emergency key plate

In US: Corbin Russwin, Inc.225 Episcopal Road

Berlin, CT 06037-4004www.corbinrusswin.com

Technical Product Support:Phone: 888-607-5703 Fax: 800-659-7293

In Canada: ASSA ABLOY Door Security Solutions Canada

160 Four Valley DriveVaughan, ON, L4K 4T9

www.assaabloy.ca