338
www.youtube.com/ntkcuttingtools www.ntkcuttingtools.com 5100 SHARP PEOPLE SHARP IDEAS SHARP TOOLS SPARK PLUGS ( USA ) , INC. App for iPad

NTK General Catalog 5100

Embed Size (px)

DESCRIPTION

Cutting tools

Citation preview

www.youtube.com/ntkcuttingtoolswww.ntkcuttingtools.com

5100

SHARP PEOPLESHARP IDEASSHARP TOOLS

SPARK PLUGS (USA), INC.

App for iPad

NTK TECHNOLOGY

Gray / Ductile Cast Iron

High Temperature Alloys

Hardened Steels

Mill Rolls Grooving

Tooling For Swiss Type Lathes

Bearing Production Steel Machining High Speed Machining ofAluminum

■ Metalcutting Safety

Applicable Products Possible Risks Safety Measures

General Cutting Tools

◎ Contact with a sharp cutting edge with bare hands may result in injury.

* Use protective gear such as protective gloves when taking the tool out of packaging and installing into the machine.

◎ Misuse or using under inappropriate conditions may cause the cutting tool to break and/or shatter into pieces, resulting in personal injury.

* Use protective equipment, machine guarding and/or protective glasses.

* Use within the range of recommended conditions. Please refer to the instruction manual and catalogue.

◎ Sudden increase in cutting resistance due to sudden impact load or excessive wear may cause the cutting tool to break and/or shatter into pieces, resulting in personal injury.

* Use protective gear such as protective gloves when taking the tool out of packaging and installing into the machine.

◎ High-temperature chips may be produced and long chips may be ejected, resulting in injury and/or burns.

* Use protective equipment, machine guarding and/or protective glasses.

* Before removing chips, always stop the machine. Wear protective gloves and use proper equipment for chip removal.

◎ The tool and material/work being cut can become very hot. Touching them immediately after use may cause burns.

*Use protective gear such as protective gloves.

◎ Sparks, heat generation due to breakage and/or chips during cutting may cause fire.

* Do not use the machine and tools in locations where there are risks of ignition or explosion.

* When using water-insoluble cutting oil, fire prevention measures must be implemented.

◎ Out of balance machine set ups when used at a high-speed, may cause insert breakage due to excess vibration or chatter, resulting in injury.

* Use protective equipment, machine guarding and/or protective glasses.

* Perform a trial-run beforehand to make sure the setup is stable, free of chatter, vibration and abnormal noise.

◎ Touching burrs and flashes on machined work may result in personal injury.

*Use adequate hand protection.

Throw-Away Type Tools

(With indexable insert)

◎ Inappropriately clamped inserts and/or components may become detached from the machine during cutting, resulting in injury.

* Before installing the insert, clean the seating surface and clamping components so that they are free of debris.* Use the wrench supplied to install the insert and check that the insert and components are securely clamped. Do not use any inserts or components other than the items specified.

◎ Excessively tightening with a device such as a pipe extension may cause the insert and/or components to break or detach due to over clamping.

* Do not use tightening devices such as pipe extensions to obtain further torque. Always use the supplied wrench.

◎ At a high speeds inserts and/or components may lose clamping pressure due to the loosening effect of centrifugal force. This is very dangerous. Always ensure secure clamping systems and check regularly.

* Use within the range the recommended conditions. Please refer to the instruction manual and catalogue.

Cutters and Rotational Tools

◎ As cutters have sharp cutting edges, contact with bare hands may result in injury.

*Use protective equipment such as protective gloves.

◎ Imbalance or eccentric rotation may cause the tool to break due to vibration or chatter, resulting in potential injury.

* Use at a rotational speed within the recommended conditions.

* To prevent eccentric rotation and vibration due to worn bearings, regularly check the machine rotor/rotating parts for the accuracy and balance and adjust as required.

Brazed Inserts / Tools

◎ Inserts may break or become, detached due to incorrect brazing.

* Use protective equipment such as machine guards and/or protective glasses. Additional guarding around the chuck and drill may be advisable.

Others

◎ It is not advisable to use repeatedly brazed inserts as the braze may progressively weaken.

* Do not use repeatedly brazed inserts as the strength of such inserts is lowered.

◎ Use only for the original and intended purpose. Using outside recommended parameters is very dangerous, causing damages to machines and/or tools.

* Always use and operate as specified, observing the required safety rules and conditions.

Guidelines for Catalog●This catalog lists products as of March 2013.

● Please note that specifications of the products listed in this catalog may be changed without notice due to continuous research & development and product improvements.

● This catalog contains the major features and relevant information on all of our products. Please contact our sales representatives or dealers if more detailed information is needed.

●Stock Status Symbols

   ●:Standard stock available for Right-Hand, Left-Hand and neutral products   R:Stock available only in Right-Hand   L:Stock available only in Left-Hand   ○:1-2 weeks delivery   Ⓡ:1-2 weeks delivery only in Right-Hand   Ⓛ:1-2 weeks delivery only in Left-Hand   ■:While stock lasts   No symbol:Not stocked

● Please note that this catalog was prepared based on products intended mainly for sale in North and South America.

■ Standard

1) Holder Type Package quantity NotesTurning holder 1 pc/caseMilling cutter 1 pc/case

2) Spare parts Package quantity Notes

Screw 10 pcs/case Clamp screw, Clamp bolt, Double screw, Button screw

Seat 10 pcs/case Shim seatClamp 10 pcs/case ClampWrench and cutter parts(such as cartridges) 5 pcs/case Wrench, bit, cutter product

Handle 1 pc/case Handle with magnet, handle and bit3) Insert Type Package quantity NotesCBN 1 pc/case B23, B30, B36, B40, B52PCD 1 pc/case PD1CTPW insert for cut-off 5 pcs/case CTPW seriesSTICK DUOSolid carbide bar 1 pc/case SHFS, SHFB, SBFS, SBFB, SBG, SBT

All others 10 pcs/case* Packaging may vary depending on the product size.   For more information, please contact your nearest dealer or our sales office.

ContentsContentsContents Cutting Tool CatalogTable of Contents

New Product Information A1 to A5

Application Introduction B1 to B10

Tool Materials / Selection Guide C1 to C14

Grade Introduction D1 to D38

Insert Item List E1 to E51

General TurningToolholders F1 to F20

ID Tooling G1 to G5

Grooving Tools H1 to H12

Milling Cutter Ⅰ1 toⅠ19

For Swiss-type Lathes J1 to J133

Infomation K1 to K12

Index L1 to L6

NEW PRODUCTS

"SX7" SiAlON ceramic ……………………………………………………………………………A2

"SP9" CVD coated silicon nitride ceramic …………………………………………………A2

"EZ CUBE" CBN grades ………………………………………………………………………A3

"DM4 / DT4" PVD coated carbide ………………………………………………………A4

"TM4" PVD coated carbide ……………………………………………………………………A4

NEW PRODUCTS FOR SWISS-TYPE LATHES"CUT DUO'' Cut-off tools for large diameter ………………………………………… J2

"BACK DUO" No-compromise quality back turning tools ………………………… J3

"Thread Whirling" Make high precision threads in a SINGLE pass…………… J4

"CL Chipbreaker" Covers extremely wide cutting range ……………………… J5

"AMX Chipbreaker" Designed for very light depth of cut …………………… J6

"UL Chipbreaker" Sharp edged negative inserts that cut like positive ……… J7

"DS-ACH Holders" Adjust centerline height simply with a wrench ………… J8

"Mogul Bar" High rigidity boring bar with excellent chip control ……………… J9

"STICK DUO Hyper" Index double-ended ID tools with ease …………… J10

"Shifted Toolholders" Solution for extended guide bushing users ……… J11

"DS Sleeve"Protect live tool stations ………………………………………………… J11

"SATURN DUO" Face grooving for small parts ………………………………… J12

"Indexable End Mills" Small diameter end mills for small parts ……… J12

A2

SP9 New coated silicon nitride ceramicNEWNEW

High speed cast iron machining with low cutting forces !

● Excellent wear resistance and toughness● Smaller edge preparation reduces cutting force● Stabilize finish applications

● Heavy interrupted machining of cast iron● Roughing to Finishing of cast iron with low tool pressure● High speed, High precision machining

Features

Features

Applications

Applications

SX7 New SiAION ceramicNEWNEW

The next step in machining aerospace alloys !

● Better notching resistance compared to whisker ceramics  No need to program ramping when compared to whisker ceramics

● Better flank wear resistance compared to other SiAlON ceramics  Superior performance vs. whisker ceramics under same conditions-even higher productivity at higher feed rates

●Excellent thermal shock resistance  High speed milling can be performed at 3000SFM or higher

● Roughing and semi finishing of heat resistant  alloys●Milling, profiling and grooving of heat resistant alloys● Best grade for pre-machined Waspaloy

➡B2・D12

➡B4・D11

New Products

A3

Grade Main binder CBN content Major applicationsB23 Ti-base 90% High speed roughing of gray cast iron, sintered metalsB30 Ti-base 95% High speed finishing of gray cast ironB36 TiCN-base 65% Light- to interrupted machining of hardened materialsB40 TiN-base 65% Interrupted machining of hardened materialsB52 TiC-base 50% Finishing of ductile cast iron and continuous machining of hardened materials

● Multiple cutting edges ― lower cost per corner

● A variety of grades optimized for different work materials and machining conditions

● Provides longer and more stable tool life in high-speed machining applications

Gray cast iron‒Rough Gray cast iron‒Finish Ductile cast iron‒FinishB23 B30 B52.004"

20°R.001"

.004"

20°

.004"

15°

R.001"

Hardened material ‒ Continuous Hardened material ‒ Light-interruption Hardened material ‒ InterruptionB52 B36 B40.004"

15°

R.001"25°

R.001"

.005"

R.001"35°

.006"

Suitable for machining Gray/Ductile cast iron Suitable for machining hardened materials

New series of multi-corner tipped inserts in new CBN grades !Cut tooling cost even further by combining with NTK ceramic tools!

〔Standard edge preparation〕 〔Standard edge preparation〕

B23

B52

6000

4500

3000

1500

.04 .08 .12

B30

Ceramic

Cutting speed(SFM)

Depth of cut(inch)

(FCD)

300

600

900

B36B52

B40

Ceramic

Cutting speed(SFM)

Continuous Light-interruption Medium interruption Interruption

〔For cast iron〕 〔For hardened materials〕

* See ceramic grades for hard turning on page B6 and B7.

■ Recommended Cutting ConditionsWork material Grade Cutting speed

(SFM)Feed rate (IPR)

Depth of cut (inch)

CoolantMaterial/other Hardness DRY WET

Gray cast iron HB‒280 B23, B30 1300‒3300 .004‒.020 .008‒.080 ○ ●

Ductile cast iron HB‒330 B52 300‒1600 .004‒.016 .008‒.080 ○ ●

Hardened steel HRC50‒68

Continuous B52 300‒1000 .004‒.020 .004‒.040 ○ ●Light-interruption B36 130‒800 .002‒.008 .004‒.040 ● ●Interruption B40 100‒500 .002‒.008 .004‒.040 ● ○

Sintered alloy HRC‒35 B23 150‒1000 .001‒.008 .002‒.020 ● ●

●1st recommendation  ○2nd recommendation

Features

NEWNEW New CBN grades

➡D24・D25

New Products

A4

DM4 / DT4 New PVD coated carbideNEWNEW

Best grade for Titanium alloys !

Extremely smooth coating for excellent surface finish !

Ultra Z coat

Excellent adhesion resistance

Excellent wear resistance

Excellent adherence to insert substrate

Smooth surface makes chip flow easier

Conventional coating

Prevent adhesion

TM4 New PVD coated carbideNEWNEW

Features

Features

Ultra Z coat

● Excellent dimensional stability and tool life thanks to the triple titanium layers adhering to the insert substrate

● Adhesion resistant hard and smooth top coating layer results in excellent surface finishes

● Excellent oxidation resistance enables high temperature machining

● Triple coating layers provide superior tool life and consistancy

● For Titanium alloys● For hard to cut materials● For high temperature alloys

DM4 DT4

Oxidation temperature(℃)Low

Low

High

High

Hardness(Hv)

TiCN DM4 / DT4

TiN TiAIN

Adhesion resistant layer (TiN)

Wear resistant layer (TiCN)

Oxidation resistant layer (TiAIN)

CarbideCarbide

➡D36

➡D36

New Products

A5

PVD Coatings

Best balance of wear resistance and adhesion resistance● For small part machining in general

TM4 TM-Coat

Best balance of heat resistance and sharp edges●Titanium alloy●Heat resistant alloy●Stainless steel●Hardened material

DT4 DT-Coat

Best wear resistance●stainless steel●Carbon steel●Alloy steel

QM3/Q15 Q-Coat

Best edge sharpness●Titanium alloy●Non-ferrous material●Stainless steel●Plastic

VM1 V-Coat

Best heat resistance● Heat resistant alloy● Stainless steel● Hardened material

DM4 DM-Coat

Best adhesion resistance● General purpose machining

ZM3/C7Z Z-Coat

Coating Specitications

Q-Coat TM-Coat DM-Coat DT-Coat V-Coat Z-Coat

Thickness Thick Thin Thick Thin Thin Thick

Wear Resistance ◎ ○ ○ ○ ○

Heat Resistance ◎ ◎ ○

Adhesion Resistance ○ ◎

Edge Sharpness ○ ○ ◎

Composition TiCN Multilayer Multilayer Multilayer TiCN TiN◎1st choice  ○2nd choice

NEW

NEWNEW

➡D30・D37

➡D36

➡D37

➡D36

➡D36

➡D31・D37

New Products

A6

ComeMoreto

www.youtube.com /ntkcutting tools

New Products

B1

Application Introduction

● Machining High Temperature Alloys with Ceramics …………………… B2● Machining Gray / Ductile Cast Iron with Ceramics …………………… B4● Machining Mill Rolls with Ceramics … B6● Machining Hardened Materials with Ceramics …………………… B7● Tooling for Swiss-type Lathes … B8● High Speed Milling of Aluminum …B10

B Application

Introduction

B2

Machining High Temperature Alloys with CeramicsSolutions for the Aerospace Industry

• Rough Turning with scale and interruptions

SX5

Notching ○

Flank Wear

Toughness ○

Heat Shock

SiAlON Ceramic

SiAlON Ceramic

• Can replace whisker ceramics by using higher feed rates• Better notching resistance compared to whisker ceramics • No need to program ramping when compared to whisker ceramics • Better flank wear resistance compared to competitor's SiAlON ceramics• Best grade for pre-machined Waspaloy• Best grade for high-speed milling

• Best grade for scale and interruptions• Best grade for machining high-cobalt alloys

■Recommended Work Materials• Waspaloy • Udimet 720• 718Plus • Rene 41

• Semi-Finish • Profiling• Milling • Grooving

■Recommended Work Materials• Inco 718 • Inco 625• Waspaloy • Udimet 720

■Recommended Applications

■Recommended Applications

■Features

■Features

Tool Life : 4.5minRCGX45, 800SFM .006IPR, .040”, WetInco 718 (pre-machined)

Tool Life : 2.0minRNG65, 950SFM .012IPR, .150”, WetWaspaloy with Scale

■Profiling of Inco 718

Competitor’s Whisker Ceramic

Competitor’s Whisker Ceramic

SX7

SX5

■Rough Turning of Waspaloy with Scale

SX7

SX5

Turbine Disk

Turbine Case

NEW➡D12

➡D13

nd ons

Be

tter F

lan

k W

ear Resistance

Semi

Rough

Wa

spa

lo

y

Better Notch

Wa

spa

lo

y

Better Notch

Be

tter F

lan

k W

ear Resistance

Semi

Rough

Application

Introduction

B3

    

 T

ou

gh

er

Finish

Inco 718

ing Resistance

ing Resistance

    

 T

ou

gh

er

Finish

Inco 718

• Semi-Finish • Profiling• Grooving

• Rough turning with scale• Milling

SX7 SX9 WA1

◎ ◎

○ ◎

◎ ◎

• Versatile grade for machining of high temperature alloys• Better flank wear resistance compared to SiAlON ceramics• Better notching resistance compared to competitor's whisker ceramics

• Tougher when compared to whisker ceramics• Extreme toughness makes higher feed and heavier DOC machining possible• Best grade for machining Inco 718 with scale

■Recommended Work Materials

■Recommended Work Materials

• Inco 718 • Inco 625

• Inco 718 • Inco 706• Inco 713

■Recommended Applications

■Recommended Applications

■Features

■Features

Tool Life : 5.0minRPGX45, 800SFM .006IPR, .040”, WetInco 718 (pre-machined)

Tool Life : 3.0minRNG65, 800SFM .010IPR, .150”, WetInco 718 with Scale

■Profiling of Inco 718

■Rough Turning of Inco 718 with Scale

Competitor’s Whisker Ceramic

Competitor’s Whisker Ceramic

WA1

SX9

Whisker-Reinforced CeramicWA1

SiAlON CeramicSX9

Turbine Case

Cover Shield

➡D9

➡D13

Turning GuidanceGrooving Guidance

➡D17➡ H4

Application GuidanceMilling Guidance

➡D14➡ Ⅰ3

Application

Introduction

B4

Machining Gray / Ductile Cast Iron with CeramicsHigh Speed Machining of Cast Irons

SP9

Notching

Flank Wear ◎

Toughness ◎

Heat Shock

CVD Coated Silicon Nitride Ceramic

TiC Ceramic Whisker Reinforced Ceramic

■Recommended Applications• Gray cast iron - Rough - Turning and milling• Ductile cast iron - Rough - Turning and milling

■Recommended Applications• Gray cast iron - Finish - Turning(HC2・HC6・WA1)• Ductile cast iron - Finish - Turning(HC6)

• Extreme toughness ‒ Tough enough to rough cast iron with T0420 (.004”X20) edge preparation• Small edge preparation ‒ Low tool pressure for stable precision machining• Turning at high feed rate thanks to the superb toughness• Dramatically reduced flank wear due to CVD coating

■Features

• Make high speed finishing of cast iron possible• Applicable for wet cutting• HC6 ‒ Optimized for finishing ductile cast iron

■Features

NEWSP9

HC2,HC6 WA1

➡D11

rced

Finish Finish

D

RY and WET

D

RY and WET

■Recommended Cutting Conditions

Work material Purpose Grade Cutting speed(SFM)

Feed(IPR / IPT)

Depth of cut(inch) DRY WET

Gray cast ironTurning

SP91200-2700 .012-.024 -.140 ● ○

Milling 1200-2700 .002-.010 -.300 ● ○

Ductile cast ironTurning

SP9800-2000 .012-.024 -.140 ○ ●

Milling 800-2000 .002-.010 -.300 ● ○

■Recommended Cutting Conditions

Work material Purpose Grade Cutting speed(SFM)

Feed(IPR)

Depth of cut(inch) DRY WET

Gray cast iron TurningHC2/HC6 1200-2100 .004-.016 -.060 ● ●

WA1 1200-2100 .004-.016 -.120 ● ●

Ductile cast iron Turning HC6 600-1500 .004-.012 -.040 ○ ●

➡D9➡D6・D7

Application

Introduction

B5

D

RY

D

RY

RoughRough

SX6 SX1 SP2

◎ ○

◎ ○

CVD Coated Silicon Nitride Ceramic

Silicon Nitride Ceramic

Alumina Oxide Ceramic

■Recommended Applications• Gray cast iron - Finish - Turning• Chilled liners - Rough / Finish - Turning(HW2)

■Recommended Applications• Gray cast iron - Rough - Turning and milling• Ductile cast iron - Rough - Turning and milling

• 1st choice for roughing gray cast iron• Applicable for wet cutting• Excellent thermal shock resistance make high speed milling possible

■Features• 1st choice for finishing gray cast iron with no coolant• Excellent wear resistance make high speed finishing possible

■Features

HC1, HW2

SX6, SX1 SP2 ➡D11

■Recommended Cutting Conditions

Work material Purpose Grade Cutting speed(SFM)

Feed(IPR)

Depth of cut(inch) DRY WET

Gray cast iron TurningHC1 1200-2100 .004-.016 .020-.080 ●

HW2 1200-2100 .004-.016 .020-.080 ●

Chilled liners Turning HW2 800-1200 .004-.012 .020-.080 ○

■Recommended Cutting Conditions

Work material Purpose Grade Cutting speed(SFM)

Feed(IPR / IPT)

Depth of cut(inch) DRY WET

Gray cast ironTurning

SX6 1800-3500 .012-.024 .020-.140 ● ●

SX1 1500-3000 .012-.024 .020-.140 ● ●

SP2 1200-2700 .008-.020 .020-.140 ● ●

Milling SX6 1500-4200 .003-.010 .020-.140 ● ○

Ductile cast iron

TurningSX6 900-1800 .005-.016 .020-.120 ○ ●

SX1 800-1600 .005-.016 .020-.120 ○ ●

MillingSX6 1200-2000 .003-.008 .020-.120 ● ○

SX1 1000-1800 .003-.008 .020-.120 ● ○

Milling Guidance ➡Ⅰ3

➡D10・D11

➡D4・D5

Application

Introduction

B6

■ HRCD ■ VRAON

Features

● Several ceramic and CBN grades for all mill-roll turning applications

● In addition to standard grade "HC2", NTK offers "HC5" and "HC7" for higher productivity

Machining Mill Rolls with CeramicsImprove Productivity

Recommended Cutting Conditions

MaterialChoice Cutting speed

(SFM) Feed (IPR)

Depth of cut (inch) DRY WET

Shore Hardness ScaleGrade 55-65 65-72 72-

Steelex. D2

1st HC7 150‒500 100% 80% 60% .004‒.012 .025‒.075 ●

2nd HC5 150‒500 100% 80% 60% .004‒.012 .025‒.075 ●

3rd HC2 150‒450 100% 80% 60% .004‒.012 .025‒.075 ●

Chilled Cast Iron

1st HC5 150‒600 100% 80% 60% .004‒.012 .025‒.075 ●

2nd HC7 150‒600 100% 80% 60% .004‒.012 .025‒.075 ●

3rd HC2 150‒450 100% 80% 60% .004‒.012 .025‒.075 ●

Ductile Cast iron1st HC5 300‒600 100% 80% 60% .004‒.012 .025‒.075 ●

2nd HC6 300‒600 100% 80% 60% .004‒.012 .025‒.075 ●

Carbide1st CBN 100‒200 .004‒.012 ‒.010 ●

2nd WA1 100‒200 .004‒.012 ‒.010 ●

CPM Rollsex. Powdered Metal

1st ZC4 150‒500 .004‒.012 .025‒.075 ●

2nd HC7 150‒500 .004‒.012 .025‒.075 ●

Holders

➡F20 ➡F19

・Hardness of the Roll is the important factor. As the roll gets harder, back off your SFM.・ DOC will depend upon the amount of material to remove. When making multiple passes with one edge, vary your DOC to move the wear to another part of the insert edge.・If you encounter Chatter, increase your Feed Rate first to get rid of it. Variable RPM controllers are helpful here to break up harmonics.

Application

Introduction

B7

Machining Hardened Materials with CeramicsDramatically Reduce Costs

ZC7/ ZC4

● ZC7 and ZC4 have excellent wear resistance needed to machine hardened materials

● ZC7 covers a wide range of applications such as carburized or induction hardened steels

● ZC4 performs the best in hardened material applications from HRc 55-70

● Wiper inserts and AG-chipbreaker improve machining efficiency

5050

100

200

300

400

500

600

700

800

55 60

HARDNESS (HRc)

SPEED (SFM)

65 70

Features

Recommended Speed Range

Recommended Cutting Conditions

AG-Chipbreaker

■ With AG-chipbreaker

■ Without AG-chipbreaker

● Good chip control● Improve surface finish● Reduce machine down time● Price advantage vs. CBN

Work material Hardness(HRc) Grade Purpose Cutting speed

(SFM)Feed (IPR) DRY WET

Hardened material30‒62 ZC7 Finish

(Continuous) 130‒700 .003‒.008● ●

55‒70 ZC4 ● ●

➡D8

Application

Introduction

B8

Application

Introduction

Tooling for Swiss type lathes

Advanced DS holders

➡J8

For front turning

➡J5

New back turning tool

➡J3

For light depth of cut

➡J6

For small diameter cut-off

➡J54

For large diameter cut-off

➡J2

For negative inserts

➡J7

A must for extended guide bushing users

➡J11

NEW NEW

NEW NEWNEW

NEW NEWNEW

B9

Application

Introduction

A great solution for chip control problems

➡J118

High quality polycrystalline diamond grade

1➡D26 New swiss tooling catalog now available

For more detail

Protection for live tool spindles

➡J11

Hight performance thread forming

➡J4

Face grooving tool

➡J12

High rigidity boring bar

➡J9

Double-ended bars with adjustable overhang

➡J10

F d t il

NEW

NEW NEW

NEW NEW

B10

utteruttererformanceerformanceighigh

High Speed Milling of Aluminum

NEWNEW

●Wide cutter diameter range  Ranging from φ.79" to φ3.94"

●No presetting required  The fixed-type HPC can be indexed only by replacing inserts※ The adjustable HPC allows adjustment of cutter variance to 5㎛ or less

●High rigidity High-reliability due to steel cutter body

●Max. speed 18000 RPM

●HPC clamping system

  The HPC insert is protected from centrifugal movement by combining the body and cartridge with an insert clamp screw

Prevents insert movement due to centrifugal force

Features

Recommended Cutting Conditions

Work material Grade Cutting speed (SFM)

Feed (IPT)

Depth of cut(inch) DRY WET

AluminumPD1 2000-12000 .002-.008 -.220 ●

TM1 1000-5000 .003-.008 -.220 ○ ●

Cartridge

Body Body

Insert clamping screwInsert

Safety design

➡Ⅰ18

Application

Introduction

C1

Tool Materials / Selection Guide

● Application Range of NTK Insert Grades ……………………………… C2● Recommended Types of Materials and Applications : Ceramics and CBN … C4

● ANSI / ISO Insert Nomenclature … C6

● Chipbreakers for Positive Inserts … C8

● Chipbreakers for Negative Inserts ……………………………………… C12

C

Tool Materials /

Selection Guide

C2

Application Range of NTK Insert Grades

PVD CoatedMicro Grain CarbideDM4DT4TM4QM3VM1ZM3

AluminaCeramic

HC1HW2

Cubic Boron NitrideB23B30B36

Al2O3-SiC Whisker CeramicWA1

Silicon Nitride CeramicSX1SX5SX6SX7SX9CVD Coated Silicon Nitride CeramicSP2SP9

Micro Grain CarbideKM1

Polycrystalline DiamondPD1

CVD Coated CarbideCP1

Low Feed High

Low

Cutting speed

HighAlumina-TiC

CeramicHC2ZC4HC5HC7ZC7

TiCCeramic

HC6

CermetXT3C7XXN4

PVDCoated Cermet

Q15C7Z

B40B52

NEW NEW

NEW

NEW

NEW

NEW

NEW

NEWNEW

Tool Materials / Selection GuideTool Materials /

Selection Guide

C3

PCarbon steelAlloy steel

MStainless steelCast steel

KGray cast ironDuctile cast iron

NAluminum alloyNonferrous metal

SInconelHastelloyWaspalloyRene

HHardened materialSteel Mills

ISO Ceramic / CBN CermetPVD coated cermetPCD

CarbidePVD coated micro-grain carbide

CVD coated carbide

01

10

20

30

40

01

10

20

30

40

01

10

20

30

HC1, HW2

KM1

QM3

ZM3

DM4

WA1

HC2, HC5, HC6

SX1, SX6

WA1

KM1

TM4

PD1

TiN coating

TiCN coating

Carbide w/o coating

Multilayer coating

Cermet

Whisker ceramic

Silicon nitride ceramic

Alumina ceramic

C B N

P C D

VM1

DT4

DT4

QM3

TM4

ZM3

QM3

CP1

VM1

TM4

XN4

SP9

SX9

C7X

C7Z

ZC7

HC7

Q15

XT3

B23, B30, B52

B36

B52

HC2, HC5, ZC4

B40

SX9

SX5

SX7

Wea

r res

istanc

eW

ear r

esistanc

eW

ear r

esistanc

e

Toug

hnes

sTo

ughn

ess

Toug

hnes

s

Wea

r res

istanc

e

Toug

hnes

s

Wea

r res

istanc

e

Toug

hnes

s

C7X

C7Z

■ Insert grade recommendation by work material type

Tool Materials /

Selection Guide

C4

Work material Tool GradeApplication

Continuous InterruptionLight interruption

CoolantRoughing Semi-finishing Finishing Dry Wet

Gray cast iron

Ceram

ic

SX6/SX1/SP2 ● ●

SP9 ● ○

HC1/HW2 ●

HC2/HC6 ● ●

WA1 ● ●

CBN

B23 ○ ●

B30 ○ ●

Chilled Liners

Ceramic HW2 ●

HC2 ● ○

Ductile cast iron

Ceram

ic SX1/SP9 ○ ●

HC6 ○ ●CBN

B52 ○ ●

Heat-resistant alloy

* Based on Using ½" IC Insert

Ceram

ic SX5 ●

SX7/SX9 ● ●

WA1 ○ ●

Hardened material

Ceramic

ZC4/ZC7 ● ●

CBN

B52 ○ ●

B36 ● ●

B40 ● ○

Rolls

* Based on Using ½" IC Insert

SteelCarbide

Ceramic WA1 ●

HC7 ●CBN

B23/B36 ●

Cast iron Ceramic

HC5/HC2/HC7 ●CBN

B30 ●

Ductile iron Ceramic

HC5/HC6 ●CBN

B52 ●

Tool Materials / Selection Guide■ Recommended Types of Materials and Applications : Ceramics and CBN ●1st Choice ○2nd Choice

(Milling) (Turning)

(Turning)

(Turning)

Tool Materials /

Selection Guide

C5

Cutting speed (SFM) Feed rate (IPR / IPT) Depth of cut (inch)

•Starting speed based on using CNGA432 insert

.02 .04 .08 .12 .16.004 .008 .012 .016 .020 .0243500

Milling

Milling

Milling

Turning

Turning

Turning

300 600 900 1200 1500 1800 2100 2400 2700 3000150

Turning

Turning Turning

TurningTurning

Turning

Milling

Milling

Tool Materials /

Selection Guide

C6

Tool Materials / Selection Guide

1 Shape

C 80°

D 55°

E 75°

L

P

R

S

T

V 35°

W 80°

2 Clearances 4 Type

11°

15°

20°

N

B

C

P

D

E

SInch N G A1 2 3 4

SMetric N G A

S TC

D K

φd

m m

φd s

3 Tolerance Class

Symbol d (inch) m (inch) s (inch)

M tolerance

M tolerance

Inscribed Circle

Inscribed Circle

d (inch)

d (inch)

1/4"3/8"1/2"5/8"3/4"1"

±.002±.002±.003±.004±.004±.005

m (inch)

m (inch)

±.003±.003±.005±.006±.006±.007

AFCHEGJKLMNU

±.0010±.0050±.0010±.0050±.0010±.0010±.0020

±.002~±.005±.002~±.005±.002~±.005±.002~±.005±.003~±.010

±.0002±.0002±.0005±.0005±.0010±.0010±.0020±.0005±.0010

±.003~±.007±.003~±.007±.005~±.015

±.0010±.0010±.0010±.0010±.0010±.0050±.0050±.0010±.0010±.0050±.0010±.0050

1/4"3/8"1/2"5/8"3/4"

±.002±.002±.003±.004±.004

±.004±.004±.006±.006±.007

6 Thickness

ThicknessS(inch)

3/32"

1/8"

5/32"

3/16"

1/4"

5/16"

3/8"

1/2"

Inch Metric

02

03

T3

04

06

07

09

12

1.5

2

2.5

3

4

5

6

8Special design

70°-90°

70°-90°

40°-60°

40°-60°

Type Symbol Type Symbol

N (E)

F

R

A

G

M

X

H

B

T

W

■ ANSI / ISO Insert Nomenclature

Tool Materials /

Selection Guide

C7

4 3 3 T 04 205 6 7 8 9 10

12 04 12 T 010 20

C D R S T V WInscribed Circle

1/4"

3/8"

1/2"

5/8"

3/4"

1"

Inch Metric

06

09

12

16

19

25

07

11

15

19

23

31

06

09

12

15

19

25

11

16

22

27

33

44

11

16

22

27

33

44

04

06

08

10

13

17

2

3

4

5

6

8

5 Symbol for Insert Size

R

7 Corner RadiusCorner Radius Inch Metric

1/64"

1/32"

3/64"

1/16"

5/64"

3/32"

1/8"

1

2

3

4

5

6

8

04

08

12

16

20

24

32

ba

r

8 Edge Condition 9 Negative land width 10 Negative land angle

Sharp FNX08

E

T

Z

S

U

K

J

P

Q

Honed

Chamfered

Chamfered and Honed

Double Chamfered

Double Chamfered and Honed

inchDescription

metrica

(inch)r

(inch)

E

T

Z

S

UKJPQ

0102010204050608040804081628607195

002004003005010012015020010020010020040070150180240

--.001.002.004.005.006.008.004.008.004.008.016.028.060.071.095

.001

.002------.001.001.002.002.003-.001.002.003

Note: K, J, P & Q show its primary land width

Description b

10

15

20

25

30

10°

15°

20°

25°

30°Note: K, J, P & Q show its primary land angle

Tool Materials /

Selection Guide

C8

Name Chipbreaker Geometry Features Chip Control Range

AMX

.012 (0.3)

DCGT32.508M shown

10°● Excellent chip control on very light depth of cut

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

AZ7

DCGT32.508M shown

.016(0.4)

● Excellent chip control at light feed and light depth of cut

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

ZR

DCMT32.508 shown

.031(0.8)

● Covers a wide range of depth of cut under high-speed and low-feed conditions

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

QD

DCMT32.508 shown

.051 (1.3)

● Provides stable machining with tough cutting edge processed by fine honing

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

AM3

.047(1.2)

DCGT32.508 shown

● All-purpose chipbreaker● First choice for most applications

● Great combination of sharp edge and chip control

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

CL

.189 (4.8)

DCGT32.508M shown

17°

● Double-positive geometry● Sharp edge and low tool pressure

● Very wide chip control range .016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

1L

.264 (6.7)

DCGT32.508 shown

16°

● Double-positive design with low tool pressure

● Tough cutting edge and excellent performance in combination with QM3

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

■ Molded Chipbreakers for Positive Inserts

Chipbreakers for Positive inserts

➡J6

➡J5

Tool Materials /

Selection Guide

C9

Name Chipbreaker Geometry Features Chip Control Range

FG

.059 (1.5)

TPGH221 shown

17°

● Exclusively designed for ID boring

● Evacuate chips BACKWARD at light depth of cut

● Sharp cutting edge with high rake angle

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

AF1

CCGT32.508 shown

.031(0.8)

● Produces remarkable surfaces in semi-finishing of steels

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

AM5

.035 (0.9)

CPGH21.508 shown

●Chipbreaker for boring● Provides both good cutting performance and chip control .016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (inch)

.12

.08

.04

.02

.02 .04 .08 .12Feed (IPR)

Depth of cut (inch)

CLZR

AM3

AZ7

AMX

Feed (IPR)

Depth of cut (inch) .12

.08

.04

.02

.02 .04 .08 .12

AT/S/UHG/U/U1

F05・F1KHG/KKHG/KKHG/KKHG/K

Molded Chipbreakers Ground Chipbreakers

■ Molded Chipbreakers for Positive Inserts (continued)

➡J9

Tool Materials /

Selection Guide

C10

Name Chipbreaker Geometry Features Chip Control Range

KHG

DCET32.508 shown

.040 (1.0)

14°

● Excellent chip control on finishing cuts

● For super high-precision machining

* Precision tolerance in corner radius: ±.0004"

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

K

TPGHP7308 shown

.040 (1.0)

15°

● Superb chip control on finishing applications

● Sharp cutting edge with the high rake angle .016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (inch)

UHG

.043 (1.1)

R

DCET32.504M shown

●Sharp cutting edge● Covers wide cutting condition range

* Precision tolerance in corner radius: ±.0004"

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

U/U1

DCGT32.508 shown

R

.063 (1.6)● Sharp cutting edge prevents work materials from work hardening

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

S

DCGT320.508 shown

15°

.040 (1.0) ● Standard ground chipbreaker with wide cutting condition coverage

● Sharp cutting edge with excellent chip control

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

AT 15°

.040 (1.0)

R

DCGT32.508 shown

● Excellent adhesion resistance with dimensional stability

● Best for small diameter parts and for machining low carbon steels

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

FM

.028 (0.7)

DCGT32.508 shown

● Full-peripheral ground chipbreaker

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

■ Ground Chipbreakers for Positive Inserts

Chipbreakers for Positive insertsTool Materials /

Selection Guide

C11

Name Chipbreaker Geometry Features Chip Control Range

F05

TPGP5208 shown

.051 (1.3) ● Exclusively designed for ID boring

●Evacuate chips BACKWARD● Excellent choice for blind hole machining

Chip backward

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

F1

TPGP2208 shown

.071 (1.8)

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

B1

TCGP5208 shown

.024 (0.6)

10°

.006 (0.15)

● Stable cutting in boring thanks to sharp and tough cutting edge

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

B2

TPGP7308 shown

.040 (1.0)

10°

.006 (0.15)

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

B3

TPGP6308 shown

.051 (1.3)

10°

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

A

CPGP0308 shown

.040 (1.0)

14°

.006(0.15)

● Tough cutting edge and good chip control● General-purpose ID chipbreaker

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

A1

A

A1

CPGP8308 shown

.031 (0.8)

14°

.006(0.15)

A2

ERGP52Y shown

.031 (0.8)

20°

● Control chips at light feed and light depth of cut

● Sharp cutting edge due to large rake angle .016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (inch)

■ Ground Chipbreakers for Positive Inserts (continued)

➡J9

➡J9 Tool Materials /

Selection Guide

C12

Name Chipbreaker Geometry Features Chip Control Range

UL

TNGG3304M shown

20°

.157(4.0) ● Negative insert with positive insert's chipbreaker

● Reduced burr Improved microfinish

● Superb advantage in cost per corner over positive inserts

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

ZF1

CNMG432 shown

● Cut small curled chips on finishing cuts

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

WM

CNMG431 shown

● Remarkable chip control in the low feed range

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

ZW1

CNMG432 shown

.005 (0.13)● Versatile chipbreaker with remarkable chip control performance in a wide range

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

ZP

CNMG432 shown

● Double-positive rake and sharp cutting edge

● Low tool pressure even at heavy depth of cut .016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (inch)

Z5

CNMG432 shown

.008 (0.2) ● Very tough insert● Suitable for high loaded interrupted machining

● Designed for machining with heavy interruption

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

WV

CNMG432 shown

.008 (0.2)

● Offers the advantages of both tough cutting edge and chip control

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

G

CNMG432 shown

.008 (0.2)

● Tough chipbreaker for roughing with exceptional stability

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

■ Molded Chipbreakers for Negative Inserts

Chipbreakers for Negative inserts

➡J7

Tool Materials /

Selection Guide

C13

Name Chipbreaker Geometry Features Chip Control Range

DA

TNGG3304 shown

.098 (2.5)

15°

● Excellent chip control and sharp cutting edge

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

D1

TNEG3308 shown

.098 (2.5)

.002 (0.05) 15°

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

N1

.059 (1.5)

14°

TNGG3308 shown

● Double-positive design with the large rake angle●Excellent chip control

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

U2

TNGG3308 shown

.091 (2.3)

R

● Reduced burr and work hardening due to high rake design

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

B

TNGG331 shown

.008(0.2) .059 (1.5)

14°

● General-purpose chipbreaker with excellent toughness and chip control

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

C

TNGG3308 shown

.087 (2.2)

14°

.008(0.2)

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

■ Ground Chipbreakers for Negative Inserts

Feed (IPR)

Depth of cut (inch) .12

.08

.04

.02

.02 .04 .08 .12

ULZP

WWMW

ZF1

Feed (IPR)

Depth of cut (inch) .12

.08

.04

.02

.02 .04 .08 .12

D1 U2

DA

Molded Chipbreakers Ground Chipbreakers

Tool Materials /

Selection Guide

C14

Tool Materials / Selection Guide

■ Positive Inserts

.12

.08

.04

.02

.02 .04 .08 .12Feed (IPR)

Depth of cut (inch)

CLZR

AM3

AZ7

AMX

Feed (IPR)

Depth of cut (inch) .12

.08

.04

.02

.02 .04 .08 .12

AT/S/UHG/U/U1

F05・F1KHG/KKHG/KKHG/KKHG/K

■ Negative Inserts

Feed (IPR)

Depth of cut (inch) .12

.08

.04

.02

.02 .04 .08 .12

ULZP

WWMW

ZF1

Feed (IPR)

Depth of cut (inch) .12

.08

.04

.02

.02 .04 .08 .12

D1 U2

DA

Molded Chipbreakers

Molded Chipbreakers

Ground Chipbreakers

Ground Chipbreakers

Tool Materials /

Selection Guide

D1D1

Grade Introduction

Grade Introduction

■Ceramics …………………………… D1●Overview of Ceramic Inserts … D2●Alumina-based Ceramics …… D4●Alumina TiC-based Ceramics … D6●Whisker-reinforced Ceramics … D9●Silicon Nitride-based Ceramics D10●SiAION Ceramics …………… D12● Guideline for Machining  Heat Resistant Alloys ……… D14

■CBN / PCD ……………………… D23■Cermet / Coated Cermet …… D27■Carbide / Coated Carbide …… D33

D

D2

Ceramics

●Alumina-based ceramics(White ceramics)

For Gray Cast Iron

●Silicon nitride-based ceramicsFor Gray Cast IronDuctile Cast IronHeat Resistant Alloys

■ Advantages of ceramic cutting tool (1) ■ Advantages of ceramic cutting tools (2)

●Alumina TiC-based ceramics(Black ceramics)

For Gray Cast IronDuctile Cast IronHardened MaterialsMill Rolls

●Whisker-based ceramicsFor Heat Resistant AlloysGray Cast IronHardened MaterialsMill Rolls

NTK’s premium ceramic grades ensure the user higher productivity. All of the grades show superior high temperature hardness, heat resistance and chemical stability. NTK offers many types of ceramic cutting tool materials (silicon nitride-based, alumina-based and whisker-based) in a variety of geometries to meet customer demands.

22

20

18

16

14

12

10

8

6

40 200 400

Temperature (℃)

Carbide P10

Cermet

Black ceramic HC2

White ceramic HC1

Silicon nitride-based SX6

Vickers Hardness (GPa)

【 Hardness at high temperature by tool material 】

600 800 1000 1200

The material retains high hardness even at

increased temperatures !!

Excellent wear resistance at high cutting speed

1600

1400

1200

1000

800

600

400

200

00 200 400

Transverse rupture strength. (MPa)

600 800 1000 1200 1400

Carbide P10

Cermet

Black ceramic HC2

White ceramic HC1

Silicon nitride-based SX6

Low impact on bendingstrength even under high

temperature

【 Breaking strength at high temperature by tool material 】

Stable machining is possible in the high speed range

Temperature (℃)

Grade Introduction

[ Ceram

ics ]

D3

Grade / Coating Applications / Features

Physical properties*

Application mapDensity

/㎠

Hardness

HRA

Bending strength

MPa

Young'smodulus

GPa

Thermalexpansioncoefficient

X10-6/K

Thermalconductivity

W/m・K

Whit

e cera

mics

Alum

ina - b

ased

ceram

ics HC1

Al2O3

KSemi-finish / Finish 4.0 94.0 700 400 7.8 17

【Gray cast iron, Finish, DRY, White ceramics】

HC1

HW2

High

HighToughness / strength

Wear resistance

Best wear resistance

HW2

Al2O3

KRough / Semi-finish / Finish 4.1 94.0 750 390 7.8 19Outstanding fracture toughness

Blac

k ce

ramics

Alumina + TiC-bas

ed ceram

ics

HC2

Al2O3+TiC

K HSemi-finish / Finish 4.3 94.5 800 420 7.9 21 【Gray cast iron, Finish, WET, Black ceramics】

HC6HC2

HC7/ ZC7

High

HighToughness / strength

Wear resistance

HC2

【Machining of hardened materials】

ZC4 HC7/ZC7

Wear resistance

High

HighToughness / strength

General black ceramic

ZC4

Al2O3+TiC

K HSemi-finish / Finish 4.6 95.5 1,000 420 7.8 25Competitive vs CBN

HC5

Al2O3+TiC

KSemi-finish / Finish 4.3 95.0 900 420 7.8 25Stable performance for Mill Rolls

HC6

TiC+Al2O3

KSemi-finish / Finish 4.7 94.0 800 450 7.6 29Excellent performance for Ductile

HC7

Al2O3+TiC

K HSemi-finish / Finish 4.6 95.0 1,100 420 7.9 23Stable performance for Mill Rolls

ZC7Al2O3+TiCTiN coat

K HSemi-finish / Finish 4.6 95.0 1,100 420 7.9 23Excellent wear resistance in wide hardness range

Silic

on N

itride - b

ased

ceram

ics

SX1

Si3N4

KRough 3.2 93.5 1,200 320 3.0 29

【Machining of Gray cast iron / Rough】

SX1

SX6

SP9

SX9

Wear resistance

High

HighToughness / strength

Wear resistance

High

HighToughness / strength

【Machining of Inco 718】

WA1 SX7

SX9SX5

Good wear resistance and toughness

SP2Si3N4

TiN+Al2O3 coat

KRough 3.2 93.5 1,100 320 3.0 29Good flank wear resistance

SX5

SiAlON

K SRough / Semi-finish 3.6 92.5 1,100 350 4.0 18Excellent toughness

SX6

Si3N4

KRough 3.2 93.5 1,200 320 3.0 501st choice for Cast Iron machining

SX7

SiAlON

K SRough / Semi-finish 3.3 93.5 900 290 3.4 11Can replace whisker ceramic

SX9

SiAlON

K SRough / Semi-finish 3.3 93.5 1,200 330 3.0 15Excellent combination of toughness and heat resistance

SP9Si3N4

TiN+Al2O3 coat

KRough / Semi-finish / Finish 3.3 93.5 1,200 330 3.0 15Low tool pressure increased toughnessDecreased tool pressure

Whiske

r - reinf

orced

ceramic

s WA1

Al2O3+SiC

K H SSemi-finish / Finish 3.7 94.5 1,200 400 7.6 35Superior flank wear resistance with toughness

*For coated grades, the values of the substrate material are indicated.

Grade Introduction

[ Ceram

ics ]

D4

Ceramics■ Alumina-based ceramics (White ceramics)

Characterized by high oxidation resistance and adhesion resistance. This ceramic utilizes alumina that is thermally and chemically stable. This ceramic is best suited for high-speed cutting applications where cutting temperature tends to be high with no coolant.

HC1 Ideal grade for high-speed finishing of cast iron !

HC1

HW2

High

HighToughness / Strength

Wear resistance

Brake rotorGray cast iron

2100 SFM

.012 IPR

.020" DOC

DRY

NTK:HC1 130 pcs

Competitor’s black ceramic 65 pcs

【Gray cast iron, Finishing, Dry cutting, White ceramic】

● Best wear resistance● Stable machining performance in many high-speed machining applications

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR)

Depth of cut(inch) DRY WET

HC1 Gray cast iron Turning Finish 1200‒2100 .004‒.016 .020‒.080 ●

Grade Introduction

[ Ceram

ics ]

D5

HW2 Alumina-based ceramic grade with high toughness !

Cylinder linerChilled liner

1200 SFM

.012 IPR

.080" DOC

DRY

NTK:HW2 70 pcs

Competitor’s white ceramic 30 pcs

● Outstanding fracture toughness● Stable machining performance in many high-speed machining applications

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR)

Depth of cut(inch) DRY WET

HW2 Gray cast iron Turning Rough-Finish 1200‒2100 .004‒.016 .020‒.080 ●

Grade Introduction

[ Ceram

ics ]

D6

Ceramics

Mill roll

240 SFM

.008 IPR

.020" - .120" DOC

DRY

NTK:HC2 20 pcs

Competitor’s black ceramic 10 pcs

HC6HC2

HC7/ ZC7

High

HighToughness / Strength

Wear resistance

HC2

ZC4 HC7/ ZC7

High

HighToughness / Strength

Wear resistance

■ Alumina TiC-based ceramics (Black ceramics)Alumina TiC-based ceramics are strengthened by adding hard carbide to highly pure alumina. This process results in ceramic materials that shows excellent performance in either wet or dry cutting conditions. As an added benefit, hardness and toughness has been improved which enables the machining of partially interrupted cuts. This ceramic material has both high-hot hardness and low plasticity needed to cut hardened materials.

【Gray cast iron, Finishing, WET, Black ceramic】 【Machining of hardened materials】

HC2 The standard grade for machining cast iron and hardened materials !

● Well-balanced content of aluminum oxide and titanium carbide (Al2O3 +TiC) sintered under pressure● Stable performance under a wide range of machining conditions● General purpose ceramic which works well in a wide range of cutting applications

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR)

Depth of cut(inch) DRY WET

HC2Gray cast iron Turning Semi finish‒Finish 1200‒2100 .004‒.016 .020‒.060 ● ●

Mill rolls(Cast iron) Turning Semi finish‒Finish 150‒500 .003‒.008 .020‒.140 ●

Grade Introduction

[ Ceram

ics ]

D7

Mill rollChilled cast iron

230 SFM

.016 IPR

.394" DOC

DRY

55″

φ53″

NTK:HC5 4 pass

Competitor’s black ceramic 2 pass

Differential case

Ductile cast iron

900 SFM

.008 IPR

.020" DOC

WET

NTK:HC6 60 pcs

Competitor’s coated carbide 30 pcs

HC5 Developed for Mill Rolls !

HC6 For machining ductile cast iron !

●Developed for use in hard turning applications for mill rolls●Excellent toughness combined with wear resistance

● Designed specifically for finish turning of ductile / nodular cast irons● TiC-based ceramic with improved wear resistance at high cutting speed

Features

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR)

Depth of cut(inch) DRY WET

HC5Mill roll(Cast iron) Turning Rough‒Finish 150‒500 .003‒.008 .020‒.140 ●

Mill roll(Steel) Turning Rough‒Finish 150‒500 .003‒.008 .020‒.140 ●

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR)

Depth of cut(inch) DRY WET

HC6 Ductile cast iron Turning Finish 600‒1500 .005‒.012 .020‒.040 ○ ●

Grade Introduction

[ Ceram

ics ]

D8

Ceramics

Side gearCase carburizing steel

Hardness:HRC63

400 SFM

.004 IPR

.006" DOC

DRY

NTK:ZC4 60 pcsCompetitor’s black ceramic 30 pcs

Gear

Carburized and hardened steel

300 SFM

.005 IPR

.006" DOC

WET

NTK:ZC7 80 pcsCompetitor’s

CBN 80 pcs

HRC58-62

ZC4 For machining hardened materials !

ZC7/ HC7 For machining hardened parts with a wide range of hardness !

● TiN-coated premium ceramic grade with the finest grain size of the all NTK ceramic grades● Best for hard turning applications from (HRC 55 - 70)● The gold coating makes edge wear easily detectable

● Excellent wear resistance in a wide range of applications such as machining carburized or induction hardened steels (HRC 30 - 62)

● High quality surface finishes with wiper facet inserts● TiN coated ZC7 is available in various geometries as standard

Features

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR)

Depth of cut(inch) DRY WET

ZC7HC7

Hardened material(HRC30-62) Turning Finish 130‒700 .003‒.008 .005‒.030 ● ●

Mill roll(Steel / Cast iron) Turning Rough ‒ Finish 150‒500 .004‒.020 .020‒.140 ● ○

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR)

Depth of cut(inch) DRY WET

ZC4 Hardened material(HRC55-70) Turning Finish 130‒700 .003‒.008 .005‒.030 ● ●

Grade Introduction

[ Ceram

ics ]

D9

Housing

Inco 625

900 SFM

.006 IPR

.020"-.030" DOC

WET

NTK:WA1 1 passCompetitor’s whisker ceramic 1 pass

WA1 Ultra high-speed machining of heat resistant alloys and cast iron !

● Best flank wear resistance at high speed● Best notch wear resistance compared to competitor's whisker-reinforced ceramics● Increased toughness compared to competitor's whisker-reinforced ceramics

Features

Wear resistance

High

HighToughness / strength

【Machining of Inco 718】

WA1 SX7

SX9SX5

■ Whisker-reinforced ceramicsWA1 ceramic grade has a unique combination of superior wear resistance, toughness and flaking resistance as a result of adding SiC whiskers to Alumina. WA1 is primarily used in machining continuous cuts of aerospace alloys because of its productivity and reliability characteristics. WA1 can also be used to machine gray cast iron and hardened steels because of its excellent thermal shock resistance.

【Heat-resistant alloy】 【WA1 structure】

Recommended applications

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR)

Depth of cut(inch) DRY WET

WA1

Heat resistantalloy Turning

Rough no scale 600‒1200 .004‒.010 .040‒.010 ●

Semi finishProfiling 600‒1500 .004‒.008 .020‒.080 ●

Grooving 600‒1200 .002‒.006 ‒ ●

Gray cast iron Turning Semi finishFinish 1200‒2100 .004‒.016 .020‒.120 ● ●

Mill roll (Carbide) Turning Rough‒Semi finish 150‒500 .003‒.008 .020‒.140 ●

Competitor’s Whisker Ceramic WA1

Grade Introduction

[ Ceram

ics ]

D10

■ Silicon Nitride-based ceramicsSilicon nitride-based ceramics have approximately twice the fracture toughness of alumina-based ceramics. Their fracture toughness is nearly the same as some carbide grades. Silicon nitride ceramic enables the user to perform productive high speed machining where traditional ceramic grades could not perform, including milling cast iron and interrupted cutting with scale.

SP2

SX1

SX6

SP9

Better

BetterToughness / strength

Wear resistance

【Gray cast iron, Roughing】

Brake rotor

Gray cast iron

2400 SFM

.025 IPR

.080" DOC

DRY

NTK:SX6 150 pcsCompetitor’s

silicon nitride ceramic 100 pcs

Cylinder block

Gray Cast Iron

330 SFM

.0043 IPT

.080″+.040″DOC

Residual coolant

NTK:SX6 150 pcsCompetitor’ssolid CBN 150 pcs

SX6 Our newest silicon nitride for machining cast iron !

● Excellent wear resistance in applications where notch wear appears● Stable tool life in the applications where thermal shock resistance is required : such as WET machining or milling● Long tool life and high productivity at high cutting speed

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR / IPT)

Depth of cut(inch) DRY WET

SX6 Cast ironTurning Rough 1500‒3500 .012‒.024 .020‒.140 ● ●Milling Rough 1500‒4200 .003‒.010 .020‒.140 ● ●

Ceramics For Cast Iron and Ductile Cast IronGrade Introduction

[ Ceram

ics ]

D11

SP9 High Speed machining with low cutting forces !

● Excellent wear-resistance and chipping resistance with CVD coated high-strength silicon nitride-based ceramic

● Achieves lower tool pressure with minimal edge preparation● Also usable for finishing

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed(IPR / IPT)

Depth of cut(inch) DRY WET

SP9Gray cast iron

Turning Rough‒Finish 1200‒2700 .012‒.024 .020‒.140 ● ○Milling Rough‒Semi finish 1200‒2500 .003‒.010 .020‒.140 ● ○

Ductile cast ironTurning Rough‒Finish 900‒1800 .006‒.016 .020‒.120 ○ ●Milling Rough‒Semi finish 2100‒3000 .003‒.010 .020‒.120 ● ○

SP2 Coated silicon nitride grade !

● Greatly improved flank wear resistance● Excellent heat resistance at high cutting speeds● High-speed rough turning of gray cast iron

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed(IPR)

Depth of cut(inch) DRY WET

SP2 Gray cast iron Turning Rough 1200‒2700 .008‒.020 .020‒.140 ● ●

Brake rotorGray cast iron1800 SFM.016 IPRDRY

NTK:SP9 120 pcs

Competitor’s silicon nitride 80 pcs

Mount bracketComp. carbide SP9

Cutter 7 tooth 10 toothCutting speed (SFM) 490 1820Feed (IPT) .008 .005Depth of cut (inch).080+.080 ⬅

DRY ⬅

NTK:SP9 390 pcs with 3.6times higher productivity

Competitor’s carbide 180 pcs

SX1 The best seller for high-speed rough machining of cast iron !

● Outstanding wear resistance by reducing binder● Improved fracture toughness● Capable of high-speed cutting

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed(IPR / IPT)

Depth of cut(inch) DRY WET

SX1Gray cast iron Turning Rough 1500‒3000 .012‒.024 .020‒.140 ● ●

Ductile cast ironTurning

Rough800‒1600 .005‒.016 .020‒.120 ○ ●

Milling 1000‒1800 .003‒.008 .020‒.120 ● ○

NEWNEWNEW

Grade Introduction

[ Ceram

ics ]

D12

■ SiAlON Ceramics● SiAlON ceramic is a silicon nitride based ceramic combined with “Al” and “O”. SiAlON ceramic offers excellent heat resistance, mechanical strength under high temperature, thermal shock resistance and wear resistance in addition to the toughness of silicon nitride.SiAlON shows superb performance in high speed machining of high temperature alloys.

● Better notching resistance compared to whisker ceramics  No need to program ramping●Better flank wear resistance compared to other SiAlON ceramics   Superior performance vs. whisker ceramics under same

conditions-even higher productivity at higher feed rates●Excellent thermal shock resistance  High speed milling can be performed at 3000SFM or higher

Features

Wea

r res

istanc

e

High

HighToughness / strength

【Machining of Inco 718】

WA1 SX7

SX9SX5

SX7 Can replace whisker ceramic !

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR / IPT)

Depth of cut(inch) DRY WET

SX7 Heat resistant alloyTurning

Rough scale 600‒1000 .004‒.010 .040‒.200 ●Rough no scale 700‒1100 .006‒.014 .040‒.100 ●

Semi finish / profiling 700‒1100 .003‒.010 .040‒.080 ●Grooving 500‒1000 .004‒.007 ‒ ●

Milling ‒ 2500‒4000 .003‒.005 .040‒.100 ●

NEWNEW

Turbine case(Waspaloy semi finish)RPGX45

φ39"

800 SFM

.012 IPR

Various DOC

WET

NTK:SX7 7.2 min

Competitor’s whisker ceramic 5.3 min * Broken

Seal(Inco 718 Finish)Comp. carbide Comp. whisker SX7

φ26"

Shape VNGA333 ⬅ ⬅Cutting speed (SFM) 160 650 800Feed (IPR) .0078 ⬅ ⬅Depth of cut (inch) .020 ⬅ ⬅

WET ⬅ ⬅Tool life 1 pass ⬅ ⬅

NTK:SX7 7 min /pc

Competitor’s whisker ceramic 15 min /pc

Competitor’s carbide 24 min /pc

Ceramics For Heat Resistant AlloysGrade Introduction

[ Ceram

ics ]

D13

SX9 Best grade for roughing Inco 718 with scale !

SX5 Best grade for roughing Waspaloy with scale !

● Excellent notch wear resistance● Toughest SiAlON grade on the market● Better thermal shock resistance compared to whisker-reinforced ceramics● Use SX5 where heavy scale or interruptions exist

● Excellent notch wear resistance● Better flank wear resistance compared to competitor's silicon nitride ceramics● Superior toughness compared to whisker-reinforced ceramics● Best thermal shock resistance● Best grade for roughing Inco 718 with scale

Features

Features

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR / IPT)

Depth of cut(inch) DRY WET

SX9 Heat resistant alloyTurning

Rough scale 450‒800 .008‒.014 .040‒.200 ●Rough no scale 600‒900 .008‒.016 .040‒.100 ●

Semi finish / profiling 600‒900 .004‒.012 .040‒.080 ●Milling ‒ 2000‒3500 .004‒.006 .040‒.100 ●

Grade Work material Application Purpose Cutting speed (SFM)

Feed (IPR / IPT)

Depth of cut(inch) DRY WET

SX5 Heat resistant alloy Turning

Rough scale 450‒800 .008‒.014 .040‒.200 ●Rough no scale 600‒900 .008‒.016 .040‒.100 ●

Semi finish / profiling 600‒900 .004‒.012 .040‒.080 ●Grooving 500‒900 .003‒.008 ‒ ●

Ring(Inco 718 with scale)Comp. whisker SX5

13.86"

5.91"

16"

Shape RCGX45 ⬅Cutting speed (SFM) 850 800Feed (IPR) .004 .010Depth of cut (inch) .750-.100 ⬅

WET ⬅

NTK:SX5 1 pass with 2.5times higher productivity

Competitor’s whisker ceramic 1 pass

Housing(Inco 718 with scale)Comp. whisker SX9

5.805"

3.983"

C/L

VANES

Shape RCGX45 ⬅Cutting speed (SFM) 600 ⬅Feed (IPR) .005 .008Depth of cut (inch) .100 ⬅

WET ⬅

NTK:SX9 * High productivity

Competitor’s whisker ceramic

Ring(Inco 718 milling with scale)Comp. whisker SX9

Shape RNG45 ⬅Cutting speed (SFM) 1200 700Feed (IPT) .0027 .004Depth of cut (inch) .010 ⬅

DRY ⬅

NTK:SX9 10 pass with high productivity

Competitor’s whisker ceramic 5 pass

Ring(Waspaloy with scale)RCGX35650 SFM.008 IPR.750-.100 DOCWET

NTK:SX5 1 pass * Small Chipping

Competitor’s SiAION ceramic 1 pass * Was chipping a lot

Grade Introduction

[ Ceram

ics ]

D14

■ Recommended Cutting Conditions (per Application)

Application Grade CoolantCutting speed Feed Depth of cut

400 600 800 1000 1200 .004 .008 .012 .016 .020 .040 .060 .080 .100 .120

Roughwith Scale SX5

WET650 (600-800) SFM .012 (.008-.014) IPR .080 (.040-.200)"

SX7800 (600-1000) SFM .008 (.004-.010) IPR .080 (.040-.200)"

SX9650 (600-800) SFM .012 (.008-.014) IPR .080 (.040-.200)"

Roughno Scale

SX5

WET

700 (600-900) SFM .014 (.008-.016) IPR .080 (.040-.100)"

SX7900 (700-1100) SFM .010 (.006-.014) IPR .080 (.040-.100)"

SX9700 (600-900) SFM .014 (.008-.016) IPR .080 (.040-.100)"

WA1900 (700-1100) SFM .006 (.004-.008) IPR .060 (.040-.080)"

Profiling&

Semi-Finish

SX5

WET

800 (600-1000) SFM .008 (.004-.012) IPR .060 (.040-.080)"

SX7900 (700-1100) SFM .008 (.004-.012) IPR .060 (.040-.080)"

SX9800 (600-1000) SFM .008 (.004-.012) IPR .060 (.040-.080)"

WA1900 (700-1200) SFM .006 (.004-.008) IPR .060 (.040-.080)"

GroovingSX7SX5 WET 900 (600-1200) SFM .006 (.004-.008) IPR

WA1900 (600-1200) SFM .002 (.002-.004) IPR

Application Grade CoolantCutting speed Feed Depth of cut

2000 2500 3000 3500 4000 .002 .003 .004 .005 .006 .020 .040 .060 .080 .100

MillingSX7 DRY

×3300 (2000-4000) SFM .004 (.003-.005) IPT .080 (.040-.100)"

SX92500 (2000-3500) SFM .005 (.004-.006) IPT .080 (.040-.100)"

Rough with scale Rough & semi-finish Profiling Grooving Milling

■ Applications

Ceramics Guidelines For Machining Heat Resistant Alloys

When using SX7/SX5, increase feed rates 100% vs. Whisker Ceramics

Grade Introduction

[ Ceram

ics ]

D15

■ Recommended Insert Grade (per Work Material)

Application Grade Inco625 Inco706 Inco713 Inco718 Inco901 Inco903 IN100 Udimet720 Rene41 Waspaloy 718Plus

Roughwith Scale SX5

SX7

SX9

Roughno Scale

SX5

SX7

SX9

WA1

Profiling&

Semi-Finish

SX5

SX7

SX9

WA1

GroovingSX7SX5

WA1

1st Choice     2nd Choice

Alternate choice

Application Grade Inco625 Inco706 Inco713 Inco718 Inco901 Inco903 IN100 Udimet720 Rene41 Waspaloy 718Plus

MillingSX7

SX9

SX5 SX7 SX9 WA1

Grade Introduction

[ Ceram

ics ]

D16

Introduction of NTK Ceramic Grades

2000

1800

1600

1400

1200

1000

800

0Light Interrupted InterruptedContinuous

Cutting Speed(SFM)

画像 製版待

Toughness

Wear ResistanceWA1WA1

SX7SX7

SX9SX9 SX5SX5

■ Correlation Chart (Inco 718)

Grade Application

Whisker - Reinforced

WA1

Grooving Finishing

SiAlON

SX7Roughing

(without scale)Semi finishing Grooving Finishing Milling

SiAlON

SX9(with or without scale)

SiAlON

SX5

(with scale)

■Application Chart

Ceramics Guidelines For Machining Heat Resistant AlloysGrade Introduction

[ Ceram

ics ]

D17

Guidelines For Success

Strength Increases

R S T D V

■ Use strong insert shapesMaximize geometry for strength productivity

■ Use largest Nose RadiusMaximize insert nose radius for strength and longer tool lifeTake into account that the larger the nose radius the greater the tool pressureTypical application machining heat resistant alloys use a RNG45 insert for roughing and CNGA43 style for finishing

■ No dwellingInserts wear out when rubbing the part instead of cutting

■ CoolantWhen turning with SX7, SX9 ,SX5 ,WA1 a flood coolant condition should be usedIn some cases where a high interruption is encountered it may be best to cut-off the coolantNo coolant should be used while milling with SX7 & SX9

■ Edge preparations.Typical cutting tool applications machining Heat resistant alloys require the insert cutting edge to be sharp. Using a slight T-land is also effective to reduce notching

■ Minimize overhangToo much overhang may cause chatter or insert breakage

■ Pre-ChamferingPre-chamferring the part reduces the potential for insert chipping or breaking upon the entry or exit point of work material

Grade Introduction

[ Ceram

ics ]

D18

● NTK ceramics bring extremely high productivity to heat resistant alloy machining● Whisker ceramics offer excellent flank wear resistance and SiAlON ceramics provide exceptional notch wear resistance● Stable machining can be performed by optimizing cutting conditions and tooling

■ Keys to successful machining of Heat Resistant Alloys

■ Troubleshooting

・Cutting Condition ➡ 1 ➡D19・Programming at Scale ➡ 2 ➡D20・Insert Grade ➡ Choose tougher grade・Insert Shape ➡ 6 ➡D22・Edge Preparation ➡ 7 ➡D22

Insert Breakage

Flaking

Heat

Chatter

・Cutting Condition ➡ 1 ➡D19・Depth of Cut ➡ 3 ➡D20・Lead Angle ➡ 4 ➡D20・Programming ➡ 5 ➡D21・Insert Grade ➡ Choose SiAlON ceramic

・Cutting Condition ➡ 1 ➡D19・Insert Grade ➡ Choose harder grade

・Cutting Condition ➡ 1 ➡D19・Programming ➡ 5 ➡D21・Edge Preparation ➡ 7 ➡D22

・Cutting Condition ➡ 1 ➡D19・Insert Shape ➡ 6 ➡D22・Edge Preparation ➡ 7 ➡D22

・Cutting Condition ➡ 1 ➡D19・Others ➡ 1 ➡D22

・Grooving infomation ➡   ➡ H4

Notching

Flank Wear

Ceramics Guidelines For Machining Heat Resistant AlloysGrade Introduction

[ Ceram

ics ]

D19

Cutting speed (SFM) Feed rate (IPR) Grade attributeSX5 SX7 SX9 WA1 SX5 SX7 SX9 WA1 SX5 SX7 SX9 WA1

Notching ➡「a」 ➡「b」 ◎

Flank wear ➡「c」 ➡「d」 ○SX7 ◎

Breakage ➡ ➡ ◎

Heat ➡ ➡ ➡ ➡ ― ―

Chatter ➡ ➡ ➡ ➡ ― ―

1Cutting Condition

Test Results

「a」 WA1 : Increase cutting speed

500 SFM 1800 SFM

「b」 SX7・SX9・SX5 : Increase feed rate

.008 IPR .016 IPR

「c」 SX7・SX9・SX5 : Decrease cutting speed

1300 SFM 500 SFM

「d」 SX7・SX9・SX5 : Increase feed rate

In some cases, in order to increase the wear resistance of SX7 & SX9 & SX5, the feed must be increased. By increasing the feed and utilizing the toughness of SX7 & SX9 & SX5, the inserts are off the part sooner causing less wear. Increasing the feed also decreases cycle time and improves productivity and profitability.

Note : Be careful to reduce the feed rate by 25%, when going into a corner.

.000 .004 .008 .012 .016 .020.000

.025

.050

.075

.100

Whisker rainforcedceramic

Feed (IPR)

Flank wear (inch)

Cutting conditionWork material : Inco718Insert shape : RNG45

Cutting Speed : 800 SFMDepth of Cut : .080"WET

SX7・SX9・SX5Whisker ceramic

Feed rate increased decreases wear amount of SiAION

■ Troubleshooting (continued)

◎1st choice  ○2nd choice

Grade Introduction

[ Ceram

ics ]

D20

f/2f

2 Scale machining

3 Depth of Cut

4 Lead Angle

When the insert breakage happens at the begin of cut scale, it might be caused by too high cutting speeds & feeds

Depth of Cut NotchingThis mode of insert failure is typical when machining heat resistant alloys. It must be controlled to prevent a catastrophic failure of the insert's cutting edge. The following information should help to minimize this probrem.

Lead AnglesWhen cutting heat resistant alloys consideration should be given to useing the largest lead angle possible. When using large lead angles, the cutting forces are spread over a larger surface area of the insert. This will also improve tool life and surface finish while reducing notching. As the lead angle increases the chip will flow more easily.

FeedsUtillize the superior strength characteristic of SX7, SX9, SX5 SiAION ceramics. If excessive wear is encountered while machining heat resistant alloys, increase the feed rate thus minimizing the cutting time.

● Typical insert wear pattern showing the effect of various lead angle changes and the resulting increase of depth of cut notching

Depth of Cut Prime consideration should be given to the effect of depth of cut upon insert tool life. There is a direct relationship between the insert radius size and the maximum depth of cut which should be taken. See the chart below for recommendations.

Knowing the hardness of the work material before the cutting begins may make all the difference between success or failure. Many times on the shop floor the operator does not know the part hardness. If this information is not known then more time is needed in the testing procedure trying to find the optimum speed and feed range. As the material hardness increases speed should decrease. Also, parts that have a forged scale work surface require a 25% speed and feed reduction until the scale is gone. This type of programing change will reduce the potential of notching as a failure mode.

Round insert Maximum DOC *Insert radius Maximum DOC1/4 .060...Less 1/32 .008...Less3/8 .090...Less 3/64 .012...Less1/2 .125...Less 1/16 .016...Less1 .250...Less 3/32 .024...Less

*OPTIMUM DOC. IS 5-15% OF THE INSERT DIAMETER *BASED ON 0º LEAD ANGLE

■ Recommended Depth of Cut Range (Inch)

-5

-5

0 015

15

45

45

Ceramics Guidelines For Machining Heat Resistant Alloys■ Troubleshooting (continued)

Grade Introduction

[ Ceram

ics ]

D21Better

Depth of Cut

α=45°

5 Programing

Same Depth of Cut Varying Depth of Cut

Ramping

● Rough

● Finish

Feed

Note) Notch wear on the insert cutting edge as shown in is the result of multiple passes being taken at the same depth of cut. This type of wear will minimize tool life. The following programming examples will help to minimize this mode of failure.

change to

Note) Another programming change that may help to reduce notching is by varying the depth of cut. Again, the same principle applies, notching takes place at various points on the cutting edge rather than concentrated at one point.

Feed

Note) Programming " Ramping " cuts in the same cutting direction is one of the best procedures to use to minimize notching. By varying the DOC, wear is distributed over the entire cutting edge not on one point.

Feed

Note) The correct procedure is to take more material off during the previous roughing application.

Then remove the amount of stock suitable for the nose radius of the insert by staying

below the 45°mark of the corner radius. This will minimize notching and allow a cut frow both directions.

45°

45°

Depth of Cut

Insert radius DOC

1/64" .005"1/32" .009"3/64" .014"1/16" .018"3/32" .028"1/8" .037"

・α=45°

■ Troubleshooting (continued)

Grade Introduction

[ Ceram

ics ]

D22

7 Edge preparation

8 Eliminate chatter

6 Insert shape

Angle

Sharper

Tougher

Width Width

Strength Increases

R S T D V

● Slightly larger T-land on the edge preparation may eliminate flaking.

Chatter problem is often caused by too much cutting pressure when machining heat resistant alloys especially in profiling or grooving. A non-rigid machine may cause excessive insert wear or insert breakage.

●Increase speeds and decrease feeds●Use harder grade with higher speed●Use smaller I.C round insert, or smaller nose radius●Reduce insert nose radius●Use positive insert●Reduce lead angle●Reduce edge preparation or use sharp edge●Minimize overhang●Try a heavy metal boring bar

Ceramics Guidelines For Machining Heat Resistant Alloys■ Troubleshooting (continued)

Grade Introduction

[ Ceram

ics ]

D23D23

Grade Introduction

CBN / PCD

●CBN (EZ CUBE) ………………… D24●PCD ……………………………… D26

D

[ CBN

/ PCD ]

D24

CBN / PCD

【Recommended cutting conditions】

【Recommended cutting conditions】

Work material Application Purpose Cutting speed(SFM)

Feed(IPR)

Depth of cut(inch) DRY WET

Cast iron Turning RoughSemi finish 1300‒3300 .004‒.020 .008‒.080 ○ ●

Sintered alloy Turning Rough‒ Finish 150‒1000 .001‒.008 .002‒.020 ● ●

Work material Application Purpose Cutting speed(SFM)

Feed(IPR)

Depth of cut(inch) DRY WET

Cast iron Turning Semi finishFinish 1300‒3300 .004‒.020 .008‒.080 ○ ●

● Five grades available to cover a variety of work materials●A wide selection in geometries● Multiple corners on both insert sides contributes to cost reduction

NTK's unique brazing technologies to ensure the bonding with the substrate.

Optimized edge prep-aration for application.● / EZ CUBE

Material grade Main binder CBN content Major application

B23 Ti-base 90% High-speed semi roughing of cast iron/sintered alloys

B30 Ti-base 95% High-speed finishing of cast iron

B36 TiCN-base 65% semi-interrupted to interrupted machining of hardened materials

B40 TiN-base 65% Interrupted machining of highly hardened materials

B52 TiC-base 50%Finishing of ductile cast iron and continuous machining of highly hardened materials

EZ CUBE Excellent performance with superb versatility at a low price !

Features

B23 ● Excellent wear resistance thanks to high CBN content

● Ideal for roughing cast iron and machining sintered materials

Features

● Excellent wear resistance thanks to high CBN content

● Designed for finishing cast iron

Features

Brake rotor

Gray cast iron

820 SFM

.0079 IPR

.079" DOC

WET

NTK:B23 210 pcs

Competitor’s CBN 70 pcs

Cylinder block

Cast iron

2600 SFM

.012 IPR

.004" DOC

WET

NTK:B30 800 pcs

Competitor’s CBN 500 pcs

B30

CBN (Cubic Boron Nitride)

NEWNEW

NEWNEWNEW

Grade Introduction

[ CBN

/ PCD ]

D25

B36

B40

B52

● Excellent combination of wear resistance and toughness due to special TiCN binders

● Best for semi-interrupted cutting of hardened materials

● Exceptional toughness thanks to special TiN binders

● Designed for severely interrupted cutting of hardened materials

● Excellent wear resistance due to optimum CBN content with special TiC binders

● Ideal for finishing ductile cast iron and continuous cuts for finishing hardened materials

Features

Features

Features

Gear(HRC61-65)

5120H

430 SFM

.006 IPR

.004" DOC

DRY

NTK:B36 50 pcs

Competitor’s CBN 20 pcs

Universal joint(HRC62)

1055

360 SFM

.0055 IPR

.0059" DOC

DRY

NTK:B40 2300 pcs

Competitor’s CBN 1500 pcs

Hub

Ductile cast iron

1150-1130 SFM

.003 IPR

.0079" DOC

WET

NTK:B52 60 pcs

Competitor’s CBN 30 pcs

Work material Application Purpose Cutting speed(SFM)

Feed(IPR)

Depth of cut(inch) DRY WET

Hardened material Turning(Light interrupted)Rough‒ Finish 130‒800 .002‒.008 .004‒.040 ● ●

Work material Application Purpose Cutting speed(SFM)

Feed(IPR)

Depth of cut(inch) DRY WET

Hardened material Turning(Heavy interrupted)Rough‒ Finish 100‒500 .002‒.008 .004‒.040 ● ໐

【Recommended cutting conditions】

【Recommended cutting conditions】

【Recommended cutting conditions】

Work material Application Purpose Cutting speed(SFM)

Feed(IPR)

Depth of cut(inch) DRY WET

Ductile cast iron Turning Finish 300‒1600 .004‒.016 .012‒.080 ໐ ●

Hardened material Turning(Continuous)Rough‒ Finish 300‒1000 .004‒.020 .004‒.040 ໐ ●

NEWNEWNEWNEW

NEWNNEWNEW

Grade Introduction

[ CBN

/ PCD ]

D26

CBN / PCD

Best for : aluminum alloys, brass, copper alloys, graphite, ceramic compact, plastics

【Recommended cutting conditions】

Work material Application Purpose Cutting speed(SFM)

Feed(IPR/IPT)

Depth of cut(inch) DRY WET

Aluminum alloyTurning Rough‒Finish ‒6500 ‒.006 ‒.200 ●

Milling Rough‒Finish ‒25000 ‒.008 ‒.200 ●

● Faster cutting speeds than carbide● Recommended for cutting aluminum and copper alloys thanks to its excellent adhesion resistance● Incorporates a very sharp cutting edge● Available for general turning and cut-off in addition to the inserts for milling cutters

● Sharp cutting edges● Enables high precision and stable machining by controlling the potential for built-up edge

Features

Spool ●Work material : A6061①Rough ②Finish

Material grade PD1GTPA25FRN01

PD1VCMW2208

Cutting speed (SFM) 660 660Feed (IPR) .004 .002Depth of cut (inch) .200 .008Life (pcs) 30000 30000

Cutting of rocker shaft holder ●Work material: ADC12 aluminumConventional cutting tool NTK

Material grade Competitor's PCD PD1Cutter specification φ1.26"×2 cutting edges φ1.26"×4 cutting edgesCutting speed (SFM) 2000 2600Revolution (RPM) 6000 8000Feed (IPT) .001 .002Table feed rate (IPM) 12 64Depth of cut (inch) ‒.240 ⬅Cutting oil WET (through coolant) ⬅ Life (pcs/corner) 8000 15000

NTK:PD1 1500 pcs

Competitor’s PCD 800 pcs

φ1.26

PD1 High-speed cutting of non ferrous metals !

PCD (polycrystalline Diamond)

Grade Introduction

[ CBN

/ PCD ]

D27D27

Grade Introduction

Cermet / PVD-coated Cermet

●Overview ………………………… D28●Cermet / PVD-coated Cermet D30

D

[ Cermet ]

D28

Cermet / PVD-coated Cermet

Cermet is a cutting tool material composed mainly of TiC (Titanium Carbide) and TiN (Titanium Nitride). The name, cermet, is derived from the words CERAMIC and METAL (representing carbide).As the name suggests, cutting performance is also in the mid-range of ceramic's and carbide's. The advantages of this material grade are high-quality and excellent surface finishes can be achieved with elevated cutting speeds. Cermets provide extended tool life.

PVD TiN or TiCN coated cermet grades bring improved wear resistance. Since the coating layer does not contain any binder components, the coating maximizes the wear resistance of the titanium which delivers excellent performance and the tool life.

High quality surface finishThe main components, TiC and TiN, have good deposition resistance as they have low affinity with work materials. Thus, machining with cermets brings high quality surface finish over extended periods of time.

High speed cuttingThe main components, TiC and TiN, are more resistant to wear and oxidation at high temperature than WC (tungsten carbide), which is the main component of carbide tools. Because of excellent wear and oxidation resistaence, cermet grades are less reactive with work materials and make stable high speed machining possible.

PVD coating with superb hardness and surface smoothness provide excellent wear resistance and adhesion resistance.

Surface finished with cermet

Cermet

Surface finished with carbide

Carbide

Smooth coating layer offers excellent adhesion resistance

Outstanding coating bonding with substrate

■ Cermet series

■ PVD-coated cermet series

Features

Features

Grade Introduction

[ Cermet ]

D29

Grade / Coating Applications / Features

Physical properties*

Applications and ceramic property mapDensity

/㎠

Hardness

HRA

Bending strength

MPa

Young'smodulus

GPa

Thermalexpansioncoefficient

X10-6/K

Thermalconductivity

W/m・K

XT3

TiC+TiN base

P M K N● Well balanced between wear resistance and toughness

6.3 92.5 1,700 450 8.4 21

Q15

TiC+TiN base+TiCN coat

P M K● Superior wear resistance and toughness

6.3 92.5 1,700 450 8.4 21

C7X

TiCN base

P M K N● Good combination of heat resistance and toughness

7.0 91.5 1,800 440 8.2 31

C7Z

TiCN base + TiN coat

P M K N● Perfect combination of heat resistance and toughness

7.0 91.5 1,800 440 8.2 31

XN4

TiN base

P M● Excellent toughness

5.9 91.5 1,900 450 8.9 42

*For coated grades, the values of the base material are indicated.

■ Applications

Q15

XT3

Continuous Light interruption Interruption

Wear resistance

■ Ductile cast iron

C7X

XN4

XT3 C7Z

Continuous Light interruption Interruption

Wear resistance

■ Steel

Material General steelCarbon steel , Alloy steel

Stainless steelStainless steel , Cast steel

Cast ironGray cast iron , Ductile cast iron

Cutting Finish Rough Finish Rough Finish Rough

Range P01 P10 P20 P30 P40 M01 M10 M20 M30 M40 K01 K10 K20 K30

Cermets

PVDCoatedcermets

Q15

XT3 XT3 XT3

Q15 Q15

C7X C7X

C7Z C7Z

XN4Grade Introduction

[ Cermet ]

D30

XT3 Well balanced combination of wear resistance and toughness !

Q15 Coated cermet for high-speed finishing of ductile cast iron !

● Well-balanced combination of wear resistance and toughness● Covers a wide range of steel cutting, from medium cutting to finishing of steel

● Further improved wear resistance and toughness from the TiCN-based coating

● The recommended grade for high-speed finishing of ductile cast iron

Features

Features

Crank shaft1049

dia. 1.08”250 SFM

.002 IPR

.001" DOC

WET

NTK:XT3 100 pcs

Competitor's cermet 60 pcs

Best for Optimized for Excellent in● Carbon steels

● Stainless steels

● Alloy steels

● Cast iron

Conventional lathes Wear resistance

Differential caseDuctile cast iron

dia. 1.18”

525 SFM

.004 IPR

.008" DOC

WET

NTK:Q15 35 pcs

Competitor's cermet 20 pcs

Best for Optimized for Excellent in● Carbon steels● Stainless steels● Alloy steels● Cast iron● Ductile cast iron

Conventional lathes Wear resistance

Cermet, PVD-coated CermetGrade Introduction

[ Cermet ]

D31

C7X High-strength cermet grade that offers remarkable machining stability !

XN4 Toughest cermet grade with excellent fracture resistance !

C7Z Combining the advantages of thermal shock resistance and fracture resistance !

● Overcomes the traditional weakness of conventional cermet grades with improved thermal shock resistance

● Excellent grade for grooving and bearing machining

● Allows for stable machining with longer tool life thanks to its excellent fracture resistance

● Further improvement in wear resistance and thermal shock resistance with a TiN-based coating

● Excellent perfprmance in grooving and bearing machining● The most recommended grade for high-speed machining of steel

Features

Features

Features

AT clutchSS800 SFM.0008-.0016 IPR.060" DOCWET

NTK:C7X 200 pcsCompetitor's cermet 100 pcs

Best for Optimized for Excellent in● Carbon steels● Stainless steels● Alloy steels● Cast iron

Swiss-type lathesConventional lathes Balance

SpringSS

dia. .079”

dia. .16”

.24”

430 SFM.002 IPR.012" DOCWET

NTK:C7Z 1600 pcsCompetitor's cermet 1200 pcs

Best for Optimized for Excellent in● Carbon steels● Stainless steels● Alloy steels● Cast iron

Swiss-type lathesConventional lathes Balance

Gear5120H

.12”

Interrupted operation required

360 SFM.004 IPR

WET

NTK:XN4 300 pcsCompetitor's cermet 200 pcs

Best for Optimized for Excellent in● Carbon steels

● Stainless steels

● Alloy steels

Conventional lathes Toughness

Grade Introduction

[ Cermet ]

MEMO

D33D33

Grade Introduction

Micro-grain Carbide, PVD / CVD-coated Carbide

●Overview ………………………… D34●PVD-coated Carbide ………… D36●Micro-grain Carbide ………… D38●CVD-coated Carbide ………… D38

D

[ Carbide

D34

Build-up edge

Flank wear

Chipping / fracture

Wear on rake

■ Micro-grain Carbide and PVD/CVD-coated CarbideExcellence in precision machining and machining of hard-to-cut materialsThese material grades use WC micro-grain carbide, the hard layer of which is granulated to a micro size 1μm as the substrate. Furthermore, the substrate is coated by the PVD method with TiN, TiCN, and/or TiAlN. The end result are materials that are suitable for precision machining and machining of difficult-to-cut materials. Inserts in these grades are tougher and harder than carbide and come with precision sharp cutting edges. They even have superior toughness and sharper cutting edges than ultra micro-grain carbide grades, with excellent wear resistance and thermal crack resistance.

General carbide structure

● Carbide grade

Micro-grain carbide structure Super micro-grain carbide structure

The result of intensive reseach and development for improving carbide gradesThe NTK carbide grade series show very stable performance under a wide range of conditions. NTK uses micro-grain carbide well balanced between wear resistance and toughness, as substrate.

Continuous research on insert tool lifeDamage to insert cutting edges vary depending on the machining process and the work material. There are various types of coatings that reduce such damages to prolong the tool life. NTK carbide series offer a variety of coated insert grades which have been developed to improve their resistance characteristics, including wear, fracture, adhesion, oxidation and the likes, by utilizing our state-of-the-art technologies.

No burrs Burrs

Relentless pursuit of better cutting performanceNTK takes pride in its carbide grade series for their outstanding cutting performance as a result of grinding ultra sharp cutting edges. This outstanding cutting performance benefits in better burr control, lower tool pressuer, stabilized dimensions and improved work hardening control.

Machined with our insert with a sharp cutting edge

Machined with a competitor's product with a honed cutting edge

Features Superior cutting performance

Features Precise analysis on insert wear patterns

Micro-grain Carbide and PVD/CVD-coated CarbideGrade Introduction

[ Carbide

D35

Grade / Coating Applications / Features

Physical properties*

Applications mapDensity

/㎠

Hardness

HRA

Bending strength

MPa

Young'smodulus

GPa

Thermalexpansioncoefficient

X10-6/K

Thermalconductivity

W/m・K

PVD coa

ted

DM4

Micro-grain carbide

+ Thick TiN-TiCN-TiAIN coat

P M S H

● Best oxidation resistance enable high temperature machining

14.4 91.0 3000 580 5.8 63

DT4

Micro-grain carbide

+ Thin TiN-TiCN-TiAIN coat

P M S H

● Excellent oxidation resistance for Swiss-type lathes 14.4 91.0 3000 580 5.8 63

TM4

Micro-grain carbide

+Thin TiN-TiCN-TiN coat

P M N S

● Best combination of wear resistance and toughness and adhesion resistance for Swiss-type lathes

14.4 91.0 3000 580 5.8 63

ZM3

Micro-grain carbide

+ Thick TiN coat

P M N

● Best Adhesion resistance enables high accuracy machining

14.4 91.0 3000 580 5.8 63

QM3

Micro-grain carbide

+ Thick TiCN coat

P M S H

● Best wear resistance enable stable machining 14.4 91.0 3000 580 5.8 63

VM1

Micro-grain carbide

+ Thin TiCN coat

P M N

● Best edge sharpness and good wear resistance 14.8 92.0 2500 640 5.7 84

Unc

oated KM1

Micro-grain carbide

P M N

● Best for non-ferrous material with mirror finish 14.8 92.0 2500 640 5.7 84

CVD

coated

CP1

Carbide + Thick film Al2O3-TiCN coat

K

● Good balance of wear resistance and toughness for cast iron machining

14.9 92.0 2400 640 ― ―

※For products with coating, the values of the base material are indicated.

QM3

HEAT RESISTA

NCE

WEAR RESISTANCE

VM1

TM4ZM3

DM4

DT4

■Correlation chart 1

VM1

ZM3ADHESION RESISTANCE

TOUGHNESS

DM4

QM3DT4

TM4

■Correlation chart 2

KM1ZM3

Hardness

Continuous InterruptionLightinterruption

■Aluminum / Brass

Grade Introduction

[ Carbide

D36

DM4 Excellent oxidation resistance !

● Best oxidation resistance for high temperature machining

● Optimized for Conventional / Swiss-type lathes

Features

CaseInco 718130 SFM.001 IPR.008" DOCWET

NTK:DM4 110 pcsCompetitor's PVD-coated carbide 90 pcs

Best for Optimized for Excellent in● Titanium alloys● Stainless steels● Alloy steels● Carbon steels● Heat resistant alloys

Conventional lathesSwiss-type lathes

Oxidation Heat resistance

DT4 Excellent heat resistance for Swiss-type lathes !

● Excellent oxidation resistance for Swiss-type lathes

Features

Pin440 CSS260 SFM.002 IPR.039" DOCWET

NTK:DT4 1100 pcsCompetitor's PVD-coated carbide 800 pcs

Best for Optimized for Excellent in● Titanium alloys● Stainless steels● Alloy steels● Carbon steels● Heat resistant alloys

Swiss-type lathes Oxidation Heat resistance

TM4 Next generation standard insert grade Swiss-type lathes !

● Excellent dimensional stability and tool life thanks to triple titanium layers with excellent adherence to insert substrate

Features

Automobile parts304 SS

φ.35

φ.45260 SFM

.0008 IPR

.047" DOCWET

NTK:TM4 950 pcsCompetitor's PVD-coated carbide 500 pcs

Best for Optimized for Excellent in● Carbon steels

● Stainless steels

● Alloy steels

Swiss-type lathes Balance

PVD-coated Carbide

NEWNEWNEW

NEWNEWNEW

NEWNEW

Grade Introduction

[ Carbide

D37

QM3 Superb wear resistance and fracture resistance in interrupted cutting !

● Excellent toughness and wear resistance for wide speed range

● Stable interrupted machining of steel

Features

Spindle4135

φ.75

φ.55

330 SFM.0012 IPR.008" DOC WET

NTK:QM3 600 pcsCompetitor's PVD-coated carbide 300 pcs

Best for Optimized for Excellent in● Carbon steels● Stainless steels● Alloy steels● Heat resistant alloys

Swiss-type lathesConventional lathes Wear resistance

ZM3 The best selling grade for automatic lathes !

● Stabilizes machining dimensions thanks to the coating being firmly adhered to the substrate

● A wide range of cutting tools in various sizes available for automatic lathes

Features

Case1010330 SFM.0047 IPR.012"‒.015" DOC WET

NTK:ZM3 6000 pcsCompetitor's PVD-coated carbide 150 pcs

Best for Optimized for Excellent in● Carbon steels● Stainless steels● Alloy steels● Non-ferrous materials

Swiss-type lathesConventional lathes Adhesion resistance

VM1 High precision machining of small diameter parts !

● Especially for machining free cutting steels (SUM materials)● For high-precision machining with longer tool life

even in the high-speed machining range

Features

Plug12L14

φ.16

460 SFM.0006 IPR.004" DOC WET

NTK:VM1 800-1000 pcsCompetitor's PVD-coated carbide 150 pcs

Best for Optimized for Excellent in● Carbon steels

● Stainless steels

● Alloy steels

Swiss-type lathes Edge sharpness

Grade Introduction

[ Carbide

D38

【Coating structure】Photo of composition (COMP)×5000

Equivalent to HRA 91.3 Young's modulus:640 GPa

Film structure Coating of highly smooth micro-grain Al2O3

Coating of micro-grain pillar-shaped TiCN

Substrate:ultra-hard carbide10μm

● Very sharp cutting edges with uncoated Micro-grain carbide

● Excellent adhesion resistance because of mirror-finish● A wide range of cutting tools in various types available

for Swiss-type lathes

Features

● High wear resistance achieved by laminating thick film TiCN layer and Al2O3 layer as the coating; Great for cast iron cutting even in high-speed range

● Excellent deposition resistance due to our original insert rake surface treatment to bring the mirror finish

● Can be also used for machining ductile cast iron

Features

KM1 Longer tool life even for machining hard-to-cut materials !

CP1 For roughing cast iron and ductile cast iron !

Spool machining5056(Aluminium)300~ 560 SFM.0016 IPR.02"‒.20" DOCWET

NTK:KM1 300 pcsCompetitor's PVD-coated carbide 200 pcs

Best for Optimized for Excellent in● Aluminium

● Plastic

● Non-ferrous materials

Swiss-type lathes Edge sharpness

HUBDuctile Cast Iron

φ.51660 SFM.0047 IPR.004" DOCWET

NTK:KM1 200 pcsCompetitor's CVD coated carbide 100 pcs

Best for Optimized for Excellent in

● Ductile cast iron

● Gray cast ironConventional lathes Wear resistance

●Sharp edge●Mirror-finish

CVD-coated Carbide

Micro-grain CarbideGrade Introduction

[ Carbide

E1

Insert Item List

●Ceramics …………………………… E2●CBN / PCD …………………………E22●Carbide / Cermet …………………E27

E

Insert Item List

E2

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

CCGW 21.51 T0225 CCGW 060204 T00525 1/4 .016 ●CCGW 21.52 T0225 CCGW 060208 T00525 1/4 .031 ●CCGW 32.51 T0425 CCGW 09T304 T01025 3/8 .016 ●CCGW 32.52 T0425 CCGW 09T308 T01025 3/8 .031 ●CCGW 431 T0420 CCGW 120404 T01020 1/2 .016 ● ●CCGW 432 T0420 CCGW 120408 T01020 1/2 .031 ● ●CCGW 433 T0420 CCGW 120412 T01020 1/2 .047 ●

■ CCGW (inch) IC TCCGW 21.5 1/4 3/32CCGW 32.5 3/8 5/32CCGW 43 1/2 3/16

Holders ➡ J26・J27・J108

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

CDH 22 P2810 CDH 1207 P07010 1/2 ● ●CDH 33 P6015 CDH 1909 P15015 3/4 ○CDH 33 Q6010 CDH 1909 Q15010 3/4 ●CDH 33 Q6010B CDH 1909 Q15010B 3/4 ●CDH 42 P8015 CDH 2512 P20015 1 ●CDH 42 P12010 CDH 2512 P30010G 1 ● ●CDH 43 P6010 CDH 2519 P15015 1 ●CDH 515 P7110B CDH 3209 P18010B 1-1/4 ●CDH 515 P7110 CDH 3209 P18010 1-1/4 ■ ●CDH 515 P8015 CDH 3209 P20015 1-1/4 ●CDH 515 Q7110 CDH 3209 Q18010 1-1/4 ● ● ●CDH 53 P8015 CDH 3219 P20015 1-1/4 ●CDH 53 Q9515 CDH 3219 Q24015 1-1/4 ● ●

■ CDH (inch) IC T HCDH 515 1-1/4 3/8 .391CDH 53 1-1/4 3/4 .391

(inch) IC T HCDH 42 1 1/2 .266CDH 43 1 3/4 .266

(inch) IC T HCDH 22 1/2 1/4 .125CDH 33 3/4 3/8 .250

Holders ➡ F20

TR

R

IC

7°80°

100°

IC H

Insert Item List

[ Ceram

ics ]

E3

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

CNG 431 T0425 CNGN 120404 T01025 1/2 .016 ○ ○CNG 431 T0525 CNGN 120404 T01225 1/2 .016 ●CNG 432 T0220 CNGN 120408 T00520 1/2 .031 ● ● ●CNG 432 T0420 CNGN 120408 T01020 1/2 .031 ● ●CNG 432 T0425 CNGN 120408 T01025 1/2 .031 ● ○ ● ○CNG 432 T0525 CNGN 120408 T01225 1/2 .031 ● ●CNG 432 T0820 CNGN 120408 T02020 1/2 .031 ○CNG 432 S0825 CNGN 120408 S02025 1/2 .031 ○CNG 432 T0825 CNGN 120408 T02025 1/2 .031 ■ ○ ○ ○CNG 433 T0220 CNGN 120412 T00520 1/2 .047 ● ● ●CNG 433 T0420 CNGN 120412 T01020 1/2 .047 ● ●CNG 433 T0425 CNGN 120412 T01025 1/2 .047 ○ ○ ● ○ ● ○CNG 433 T0525 CNGN 120412 T01225 1/2 .047 ● ●CNG 433 T0820 CNGN 120412 T02020 1/2 .047 ●CNG 433 S0825 CNGN 120412 S02025 1/2 .047 ○CNG 433 T0825 CNGN 120412 T02025 1/2 .047 ■ ■ ○ ○ ○CNG 434 T0220 CNGN 120416 T00520 1/2 .063 ● ●CNG 434 T0420 CNGN 120416 T01020 1/2 .063 ●CNG 434 T0525 CNGN 120416 T01225 1/2 .063 ●CNG 434 T0820 CNGN 120416 T02020 1/2 .063 ○CNG 434 T0825 CNGN 120416 T02025 1/2 .063 ■ ○CNG 435 T0825 CNGN 120420 T02025 1/2 .079 ○CNG 452 T0220 CNGN 120708 T00520 1/2 .031 ●CNG 452 T0825 CNGN 120708 T02025 1/2 .031 ●CNG 453 T0220 CNGN 120712 T00520 1/2 .047 ● ●CNG 453 T0825 CNGN 120712 T02025 1/2 .047 ■ ■ ●CNG 454 T0220 CNGN 120716 T00520 1/2 .063 ●CNG 454 T0825 CNGN 120716 T02025 1/2 .063 ■ ●CNG 543 T0825 CNGN 160612 T02025 5/8 .047 ●CNG 552 T0825 CNGN 160708 T02025 5/8 .031 ●CNG 554 T0220 CNGN 160716 T00520 5/8 .063 ○CNG 643 T0825 CNGN 190612 T02025 3/4 .047 ●CNG 644 T0825 CNGN 190616 T02025 3/4 .063 ●CNG 646 T0220 CNGN 190624 T00520 3/4 .094 ●CNG 648 T0825 CNGN 190632 T02025 3/4 .125 ●CNG 656 T0220 CNGN 190724 T00520 3/4 .094 ●

■ CNG (inch) IC TCNG 43 1/2 3/16CNG 45 1/2 5/16

(inch) IC TCNG 54 5/8 1/4CNG 55 5/8 5/16

(inch) IC TCNG 64 3/4 1/4CNG 65 3/4 5/16

Holders ➡ F6・F7・G4

TR

RIC 90°

80°

100°

Insert Item List

[ Ceram

ics ]

E4

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

CNGA 431 T0220 CNGA 120404 T00520 1/2 .016 ●CNGA 431 T0425 CNGA 120404 T01025 1/2 .016 ● ●CNGA 431 T0525 CNGA 120404 T01225 1/2 .016 ● ●CNGA 431 S0825 CNGA 120404 S02025 1/2 .016 ●CNGA 431 T0825 CNGA 120404 T02025 1/2 .016 ●CNGA 431 Z0825 CNGA 120404 Z02025 1/2 .016 ●CNGA 432 T0220 CNGA 120408 T00520 1/2 .031 ● ● ●CNGA 432 T0320 CNGA 120408 T00820 1/2 .031 ●CNGA 432 T0420 CNGA 120408 T01020 1/2 .031 ● ●CNGA 432 T0425 CNGA 120408 T01025 1/2 .031 ● ○ ○ ●CNGA 432 T0525 CNGA 120408 T01225 1/2 .031 ● ● ● ● ●CNGA 432 T0630 CNGA 120408 T01530 1/2 .031 ■CNGA 432 T0820 CNGA 120408 T02020 1/2 .031 ● ●CNGA 432 Z0820 CNGA 120408 Z02020 1/2 .031 ●CNGA 432 S0825 CNGA 120408 S02025 1/2 .031 ●CNGA 432 T0825 CNGA 120408 T02025 1/2 .031 ● ■ ○CNGA 432 Z0825 CNGA 120408 Z02025 1/2 .031 ●CNGA 433 T0220 CNGA 120412 T00520 1/2 .047 ● ● ●CNGA 433 T0320 CNGA 120412 T00820 1/2 .047 ●CNGA 433 T0420 CNGA 120412 T01020 1/2 .047 ● ● ●CNGA 433 T0425 CNGA 120412 T01025 1/2 .047 ● ○ ○ ●CNGA 433 T0525 CNGA 120412 T01225 1/2 .047 ● ● ● ● ●CNGA 433 T0820 CNGA 120412 T02020 1/2 .047 ● ● ●CNGA 433 Z0820 CNGA 120412 Z02020 1/2 .047 ●CNGA 433 S0825 CNGA 120412 S02025 1/2 .047 ●CNGA 433 T0825 CNGA 120412 T02025 1/2 .047 ● ■ ○ ●CNGA 433 Z0825 CNGA 120412 Z02025 1/2 .047 ●CNGA 434 T0220 CNGA 120416 T00520 1/2 .063 ● ○ ●CNGA 434 T0420 CNGA 120416 T01020 1/2 .063 ● ●CNGA 434 T0525 CNGA 120416 T01225 1/2 .063 ● ■CNGA 434 T0820 CNGA 120416 T02020 1/2 .063 ●CNGA 434 T0825 CNGA 120416 T02025 1/2 .063 ● ■ ○CNGA 542 T0825 CNGA 160608 T02025 5/8 .031 ●CNGA 543 T0220 CNGA 160612 T00520 5/8 .047 ● ●CNGA 543 T0820 CNGA 160612 T02020 5/8 .047 ●CNGA 543 T0825 CNGA 160612 T02025 5/8 .047 ● ■ ●CNGA 543 Z0825 CNGA 160612 Z02025 5/8 .047 ●CNGA 544 T0220 CNGA 160616 T00520 5/8 .063 ● ●CNGA 544 T0825 CNGA 160616 T02025 5/8 .063 ■ ●CNGA 544 Z0825 CNGA 160616 Z02025 5/8 .063 ●CNGA 642 T0825 CNGA 190608 T02025 3/4 .031 ●CNGA 643 T0220 CNGA 190612 T00520 3/4 .047 ● ●CNGA 643 T0420 CNGA 190612 T01020 3/4 .047 ●CNGA 643 T0525 CNGA 190612 T01225 3/4 .047CNGA 643 Z0620 CNGA 190612 Z01520 3/4 .047 ●CNGA 643 T0820 CNGA 190612 T02020 3/4 .047 ●CNGA 643 T0825 CNGA 190612 T02025 3/4 .047 ● ■ ● ●CNGA 644 T0220 CNGA 190616 T00520 3/4 .063 ● ●CNGA 644 T0825 CNGA 190616 T02025 3/4 .063 ● ●CNGA 648 T0825 CNGA 190632 T02025 3/4 .125 ●

■ CNGA (inch) IC TCNGA 43 1/2 3/16CNGA 54 5/8 1/4CNGA 64 3/4 1/4

Holders ➡ F6・F7・G4・J35

R T

R

IC 90°

80°

100°

Insert Item List

[ Ceram

ics ]

E5

(inch) IC TCNGA 43 WL 1/2 3/16

Holders ➡ F6・F7・G4・J35

■ CNGA-WL with wiper for higher feed

R T

RIC 90°

80°

100°

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

CNGA 432 WLM T0425 CNGA 120408 WLM T01025 1/2 .031 ● ● ●CNGA 433 WLM T0425 CNGA 120412 WLM T01025 1/2 .047 ● ● ●

(inch) IC TCNGA 43 WLM 1/2 3/16

Holders ➡ F6・F7・G4・J35

R T

R

IC 90°

80°

100°

■ CNGA-WLM with wiper for slower feed

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

CNGA 432 WL T0425 CNGA 120408 WL T01025 1/2 .031 ● ●CNGA 432 WL T0525 CNGA 120408 WL T01225 1/2 .031 ●CNGA 433 WL T0425 CNGA 120412 WL T01025 1/2 .047 ● ●CNGA 433 WL T0525 CNGA 120412 WL T01225 1/2 .047 ●CNGA 434 WL T0225 CNGA 120416 WL T00525 1/2 .063 ●CNGA 434 WL T0425 CNGA 120416 WL T01025 1/2 .063 ●

(inch) IC TCNGG 43 1/2 3/16

Holders ➡ F6・F7・G4・J35

■ CNGG with chipbreaker

100°

90°

80°

IC

R

R

TSteel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

CNGG 432 Z0430 AG CNGG 120408 Z01030 AG 1/2 .031 ●CNGG 433 Z0430 AG CNGG 120412 Z01030 AG 1/2 .047 ●

Insert Item List

[ Ceram

ics ]

E6

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

(inch) IC TCNGX 43 1/2 3/16CNGX 45 1/2 5/16

Holders ➡ F6・G4

■ CNGX

80°

90°

100° R

R

TIC

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

CNGX 432 T0320 DP5 CNGX 120408 T00820 DP5 1/2 .031 ●CNGX 432 T0420 DP5 CNGX 120408 T01020 DP5 1/2 .031 ●CNGX 432 T0820 DP5 CNGX 120408 T02020 DP5 1/2 .031 ●CNGX 433 T0220 DP5 CNGX 120412 T00520 DP5 1/2 .031 ●CNGX 433 T0320 DP5 CNGX 120412 T00820 DP5 1/2 .047 ●CNGX 433 T0420 DP5 CNGX 120412 T01020 DP5 1/2 .047 ●CNGX 433 T0820 DP5 CNGX 120412 T02020 DP5 1/2 .047 ●CNGX 434 T0420 DP5 CNGX 120416 T01020 DP5 1/2 .063 ●CNGX 434 T0820 DP5 CNGX 120416 T02020 DP5 1/2 .063 ●CNGX 452 T0220 DP5 CNGX 120708 T00520 DP5 1/2 .031 ●CNGX 452 T0320 DP5 CNGX 120708 T00820 DP5 1/2 .031 ●CNGX 452 T0820 DP5 CNGX 120708 T02020 DP5 1/2 .031 ●CNGX 452 T0825 DP5 CNGX 120708 T02025 DP5 1/2 .031 ●CNGX 453 T0220 DP5 CNGX 120712 T00520 DP5 1/2 .047 ●CNGX 453 T0320 DP5 CNGX 120712 T00820 DP5 1/2 .047 ●CNGX 453 T0420 DP5 CNGX 120712 T01020 DP5 1/2 .047 ●CNGX 453 T0820 DP5 CNGX 120712 T02020 DP5 1/2 .047 ● ●CNGX 453 T0825 DP5 CNGX 120712 T02025 DP5 1/2 .047 ● ● ●CNGX 454 T0420 DP5 CNGX 120716 T01020 DP5 1/2 .063 ●CNGX 454 T0425 DP5 CNGX 120716 T01025 DP5 1/2 .063 ■CNGX 454 T0820 DP5 CNGX 120716 T02020 DP5 1/2 .063 ● ●CNGX 454 S0825 DP5 CNGX 120716 S02025 DP5 1/2 .063 ●CNGX 454 T0825 DP5 CNGX 120716 T02025 DP5 1/2 .063 ● ●

(inch) IC TDNG 43 1/2 3/16DNG 45 1/2 5/16DNG 54 5/8 1/4

■ DNG

55°

90°

TR

IC

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

DNG 431 T0420 DNGN 150404 T01020 1/2 .016 ○DNG 432 T0220 DNGN 150408 T00520 1/2 .031 ●DNG 432 T0420 DNGN 150408 T01020 1/2 .031 ●DNG 432 T0425 DNGN 150408 T01025 1/2 .031 ○ ○DNG 432 T0525 DNGN 150408 T01225 1/2 .031 ●DNG 432 S0825 DNGN 150408 S02025 1/2 .031 ○DNG 433 T0220 DNGN 150412 T00520 1/2 .047 ●DNG 433 T0420 DNGN 150412 T01020 1/2 .047 ●DNG 433 T0625 DNGN 150412 T01525 1/2 .047 ●DNG 433 T0825 DNGN 150412 T02025 1/2 .047 ○DNG 434 T0220 DNGN 150416 T00520 1/2 .063 ●DNG 434 T0420 DNGN 150416 T01020 1/2 .063 ●DNG 434 T0425 DNGN 150416 T01025 1/2 .063 ●DNG 453 T0825 DNGN 150712 T02025 1/2 .047 ○ ●DNG 454 T0825 DNGN 150716 T02025 1/2 .063 ■ ●DNG 543 T0825 DNGN 190612 T02025 5/8 .047 ●

Insert Item List

[ Ceram

ics ]

E7

(inch) IC TDNGA 44 1/2 1/4DNGA 54 5/8 1/4

(inch) IC TDNGA 33 3/8 3/16DNGA 43 1/2 3/16

Holders ➡ F8・F9・G4

■ DNGA

55°

90°

TR

IC

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

DNGA 331 T0820 DNGA 110404 T02020 3/8 .016 ●DNGA 431 T0220 DNGA 150404 T00520 1/2 .016 ●DNGA 431 T0425 DNGA 150404 T01025 1/2 .016 ● ○ ○DNGA 431 T0525 DNGA 150404 T01225 1/2 .016 ●DNGA 431 S0825 DNGA 150404 S02025 1/2 .016 ●DNGA 431 Z0825 DNGA 150404 Z02025 1/2 .016 ● ●DNGA 432 T0220 DNGA 150408 T00520 1/2 .031 ● ● ●DNGA 432 T0320 DNGA 150408 T00820 1/2 .031 ●DNGA 432 T0420 DNGA 150408 T01020 1/2 .031 ● ●DNGA 432 T0425 DNGA 150408 T01025 1/2 .031 ○ ○ ●DNGA 432 T0525 DNGA 150408 T01225 1/2 .031 ● ● ● ●DNGA 432 T0820 DNGA 150408 T02020 1/2 .031 ● ●DNGA 432 S0825 DNGA 150408 S02025 1/2 .031 ○ ●DNGA 432 T0825 DNGA 150408 T02025 1/2 .031 ● ■ ○ ●DNGA 432 Z0820 DNGA 150408 Z02020 1/2 .031 ●DNGA 432 Z0825 DNGA 150408 Z02025 1/2 .031 ●DNGA 433 T0220 DNGA 150412 T00520 1/2 .047 ● ● ●DNGA 433 T0320 DNGA 150412 T00820 1/2 .047 ●DNGA 433 T0420 DNGA 150412 T01020 1/2 .047 ● ●DNGA 433 T0425 DNGA 150412 T01025 1/2 .047 ○ ○DNGA 433 T0525 DNGA 150412 T01225 1/2 .047 ● ●DNGA 433 T0820 DNGA 150412 T02020 1/2 .047 ● ●DNGA 433 S0825 DNGA 150412 S02025 1/2 .047 ●DNGA 433 T0825 DNGA 150412 T02025 1/2 .047 ● ■ ● ●DNGA 433 Z0825 DNGA 150412 Z02025 1/2 .047 ●DNGA 434 T0220 DNGA 150416 T00520 1/2 .063 ●DNGA 434 T0420 DNGA 150416 T01020 1/2 .063 ●DNGA 434 T0525 DNGA 150416 T01225 1/2 .063 ●DNGA 434 S0820 DNGA 150416 S02020 1/2 .063 ●DNGA 436 T0420 DNGA 150424 T01020 1/2 .094 ●DNGA 442 T0825 DNGA 150608 T02025 1/2 .031 ●DNGA 542 T0820 DNGA 190608 T02020 5/8 .031 ●DNGA 543 T0820 DNGA 190612 T02020 5/8 .047 ●DNGA 544 T0825 DNGA 190616 T02025 5/8 .063 ●

Holders ➡ F8・F9・G4

■ DNGG with chip-breaker (inch) IC TDNGG 43 1/2 3/16

55°

RT

90°IC

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

DNGG 432 Z0430 AG DNGG 150408 Z01030 AG 1/2 .031 ●DNGG 433 Z0430 AG DNGG 150412 Z01030 AG 1/2 .047 ○

Insert Item List

[ Ceram

ics ]

E8

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Holders ➡ F8・F9・G4

■ DNGX (inch) IC TDNGX 1207 .394 5/16DNGX 45 1/2 5/16

55°

ICRT

90°

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

DNGX 120712 T0820 DP5 DNGX 120712 T02020 DP5 .394 .047 ■DNGX 120712 T0825 DP5 DNGX 120712 T02025 DP5 .394 .047 ●DNGX 452 T0220 DP5 DNGX 150708 T00520 DP5 1/2 .031 ●DNGX 452 T0825 DP5 DNGX 150708 T02025 DP5 1/2 .031 ●DNGX 453 T0825 DP5 DNGX 150712 T02025 DP5 1/2 .047 ●DNGX 454 T0825 DP5 DNGX 150716 T02025 DP5 1/2 .063 ● ○

■ LNJ / LNM (inch) W L TLNJ / M 6688 3/4 1-1/2 1/2

90°

L

W

RT

90°

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

LNJ 6688 P6015 LNJ 6688 P15015 .125 ■ ●LNJ 6688 Q8015 LNJ 6688 Q20015 .125 ● ●LNM 6688 S6015 LNM 6688 SN2 .125 ○LNM 6688 SNX2 LNM 6688 SNX2 .125 ○LNM 6688 SNX6 LNM 6688 SNX6 .125 ○

Insert Item List

[ Ceram

ics ]

E9

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

RCGX 23 T0220 RCGX 060400 T00520 1/4 ● ● ●RCGX 23 T0320 RCGX 060400 T00820 1/4 ●RCGX 25 T0220 RCGX 060700 T00520 1/4 ● ● ●RCGX 25 Z0820 RCGX 060700 Z02020 1/4 ●RCGX 35 E02 RCGX 090700 E004 3/8 ●RCGX 35 T0220 RCGX 090700 T00520 3/8 ● ● ●RCGX 35 T0320 RCGX 090700 T00820 3/8 ● ●RCGX 35 T0420 RCGX 090700 T01020 3/8 ● ●RCGX 35 Z0420 RCGX 090700 Z01020 3/8 ●RCGX 35 Z0820 RCGX 090700 Z02020 3/8 ●RCGX 45 E02 RCGX 120700 E004 1/2 ● ●RCGX 45 T0220 RCGX 120700 T00520 1/2 ● ● ●RCGX 45 T0320 RCGX 120700 T00820 1/2 ● ●RCGX 45 T0420 RCGX 120700 T01020 1/2 ● ●RCGX 45 Z0620 RCGX 120700 Z01520 1/2 ●RCGX 45 Z0820 RCGX 120700 Z02020 1/2 ●

Holders ➡ F17・F18・F19

■ RCGX (inch) IC T θRCGX 23 1/4 3/16 120RCGX 25 1/4 5/16 120RCGX 35 3/8 5/16 120RCGX 45 1/2 5/16 120

θ

IC T

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

RCGX 101 P2010 3/16 ●RCGX 102 P4815 1/4 ● ● ●RCGX 102 T0225 1/4 ● ●RCGX 102 T0820 1/4 ●RCGX 103 P4815 3/8 ● ●RCGX 103 P8015 3/8 ●RCGX 103 T0820 3/8 ●RCGX 103 T0825 3/8 ●RCGX 103 T1625 3/8 ●RCGX 104 P6015 1/2 ● ● ●RCGX 104 P8015 1/2 ●RCGX 104 T0820 1/2 ●RCGX 104 T1625 1/2 ●RCGX 105 P4815 5/8 ● ●RCGX 105 P8015 5/8 ●RCGX 105 S8020 5/8 ● ●RCGX 106 P4815 3/4 ●RCGX 106 P8015 3/4 ● ● ●RCGX 108 P8015 1 ●

Holders ➡ F18・F19

■ RCGX10 (inch) IC T θRCGX 105 5/8 .388 120RCGX 106 3/4 .388 120RCGX 108 1 .461 140

(inch) IC T θRCGX 101 3/16 .240 90RCGX 102 1/4 .309 120RCGX 103 3/8 .309 120RCGX 104 1/2 .312 120

IC T

θ

Insert Item List

[ Ceram

ics ]

E10

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

RNG 32 T0220 RNGN 090300 T00525 3/8 ●RNG 32 T0425 RNGN 090300 T01025 3/8 ●RNG 32 T0525 RNGN 090300 T01225 3/8 ●RNG 33 T0320 RNGN 090400 T00820 1/2 ●RNG 33 T0825 RNGN 090400 T02025 3/8 ●RNG 42 T0425 RNGN 120300 T01025 1/2 ●RNG 43 T0220 RNGN 120400 T00520 1/2 ● ● ●RNG 43 T0225 RNGN 120400 T00525 1/2 ○ ○RNG 43 T0320 RNGN 120400 T00820 1/2 ●RNG 43 T0420 RNGN 120400 T01020 1/2 ● ● ●RNG 43 T0425 RNGN 120400 T01025 1/2 ○ ● ○RNG 43 T0525 RNGN 120400 T01225 1/2 ● ●RNG 43 T0820 RNGN 120400 T02020 1/2 ●RNG 43 S0825 RNGN 120400 S02025 1/2 ○RNG 43 T0825 RNGN 120400 T02025 1/2 ● ■ ○RNG 43 Z0825 RNGN 120400 Z02025 1/2 ● ●RNG 43 T2820 RNGN 120400 T07020 1/2 ●RNG 45 E01 RNGN 120700 E002 1/2 ● ●RNG 45 E02 RNGN 120700 E004 1/2 ●RNG 45 E03 RNGN 120700 E007 1/2 ○RNG 45 T0220 RNGN 120700 T00520 1/2 ● ● ●RNG 45 T0225 RNGN 120700 T00525 1/2 ○ ○RNG 45 T0320 RNGN 120700 T00820 1/2 ●RNG 45 T0420 RNGN 120700 T01020 1/2 ● ● ● ●RNG 45 Z0620 RNGN 120700 Z01520 1/2 ●RNG 45 S0825 RNGN 120700 S02025 1/2 ●RNG 45 T0825 RNGN 120700 T02025 1/2 ■ ● ○RNG 45 Z0825 RNGN 120700 Z02025 1/2 ● ●RNG 45 P2810 RNGN 120700 P07010 1/2 ●RNG 55 T0220 RNGN 150700 T00520 5/8 ● ● ●RNG 55 T0225 RNGN 150700 T00525 5/8 ○ ○RNG 55 T0320 RNGN 150700 T00820 5/8 ●RNG 64 T0825 RNGN 190600 T02025 3/4 ●RNG 64 P6010 RNGN 190600 P15010 3/4 ●RNG 65 T0220 RNGN 190700 T00520 3/4 ● ● ●RNG 65 T0225 RNGN 190700 T00525 3/4 ○RNG 65 T0320 RNGN 190700 T00820 3/4 ●RNG 65 T0420 RNGN 190700 T01020 3/4 ● ●RNG 85 T0220 RNGN 250700 T00520 1 ● ○ ○RNG 85 S6015 RNGN 250700 S15015 1 ●RNG 86 T0220 RNGN 250900 T00520 1 ●

■ RNG (inch) IC TRNG 85 1 5/16RNG 86 1 3/8

(inch) IC TRNG 32 3/8 1/8RNG 33 3/8 3/16RNG 42 1/2 1/8RNG 43 1/2 3/16

(inch) IC TRNG 45 1/2 5/16RNG 55 5/8 5/16RNG 64 3/4 1/4RNG 65 3/4 5/16

90°IC

T

Holders ➡ F16Cutters ➡ Ⅰ5 

Insert Item List

[ Ceram

ics ]

E11

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

RPGX 23 T0220 RPGX 060400 T00520 1/4 ● ●RPGX 35 E02 RPGX 090700 E004 3/8 ●RPGX 35 T0220 RPGX 090700 T00520 3/8 ● ● ●RPGX 35 T0320 RPGX 090700 T00820 3/8 ●RPGX 35 T0420 RPGX 090700 T01020 3/8 ●RPGX 45 E02 RPGX 120700 E004 1/2 ●RPGX 45 T0220 RPGX 120700 T00520 1/2 ● ● ●RPGX 45 T0320 RPGX 120700 T00820 1/2 ●RPGX 45 T0420 RPGX 120700 T01020 1/2 ● ●

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

RPG 21.5 E02 RPGN 060200 E004 1/4 ●RPG 21.5 T0220 RPGN 060200 T00520 1/4 ● ● ●RPG 21.5 T0320 RPGN 060200 T00820 1/4 ●RPG 32 E02 RPGN 090300 E004 3/8 ●RPG 32 T0220 RPGN 090300 T00520 3/8 ● ●RPG 32 T0320 RPGN 090300 T00820 3/8 ●RPG 32 T0425 RPGN 090300 T01025 3/8 ●RPG 42 T0525 RPGN 120300 T01225 1/2 ●RPG 43 E01 RPGN 120400 E002 1/2 ●RPG 43 E02 RPGN 120400 E004 1/2 ●RPG 43 T0220 RPGN 120400 T00520 1/2 ● ● ●RPG 43 T0225 RPGN 120400 T00525 1/2 ○RPG 43 T0320 RPGN 120400 T00820 1/2 ●RPG 43 T0420 RPGN 120400 T01020 1/2 ● ● ● ●RPG 43 Z0620 RPGN 120400 Z01520 1/2 ●RPG 43 Z0825 RPGN 120400 Z02025 1/2 ●RPG 65 T0220 RPGN 190700 T00520 3/4 ●

Cutters ➡ Ⅰ4

Holders ➡ F17・F18・F19

■ RPG

■ RPGX

(inch) IC TRPG 43 1/2 3/16RPG 65 3/4 5/16

(inch) IC TRPG 21.5 1/4 3/32RPG 32 3/8 1/8RPG 42 1/2 1/8

11°

TIC

(inch) IC T θRPGX 23 1/4 3/16 120RPGX 35 3/8 5/16 120RPGX 45 1/2 5/16 120

11°

IC T

φ

Insert Item List

[ Ceram

ics ]

E12

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

SCG 333 T0425 SCGN 090412 T01025 3/8 .047 ■SCG 433 T0425 SCGN 120412 T01025 1/2 .047 ■

■ SCG (inch) IC TSCG 33 3/8 3/16SCG 43 1/2 3/16

90°7°

RIC

T

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

SDCW 432 T0420 SDCW 120408 T01020 1/2 .031 ● ● ○SDCW 433 T0420 SDCW 120412 T01020 1/2 .047 ● ●SDCW 434 T0420 SDCW 120416 T01020 1/2 .063 ● ●

Cutters ➡ Ⅰ14・Ⅰ15・Ⅰ16

■ SDCW (inch) IC TSDCW 43 1/2 3/16

IC R

15°

T

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

SCGW 32.52 T0420 SCGW 09T308 T01020 3/8 .031 ● ●SCGW 32.53 T0420 SCGW 09T312 T01020 3/8 .047 ●SCGW 431 T0420 SCGW 120404 T01020 1/2 .016 ●SCGW 432 T0420 SCGW 120408 T01020 1/2 .031 ●

■ SCGW(inch) IC T

SCGW 32 3/8 5/12SCGW 43 1/2 3/16

IC R T

Insert Item List

[ Ceram

ics ]

E13

■ SNG3 / SNG4S / NG5 (inch) IC TSNG 32 3/8 1/8SNG 33 3/8 3/16SNG 43 1/2 3/16

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

SNG 322 T0425 SNGN 090308 T01025 3/8 .031 ■ ○ ●SNG 322 T0525 SNGN 090308 T01225 3/8 .031 ●SNG 324 T0425 SNGN 090316 T01025 3/8 .063 ○ ○SNG 324 T0525 SNGN 090316 T01225 3/8 .063 ●SNG 332 T0425 SNGN 090408 T01025 3/8 .031 ○SNG 333 T0425 SNGN 090412 T01025 3/8 .047 ○SNG 431 T0425 SNGN 120404 T01025 1/2 .016 ○SNG 432 T0220 SNGN 120408 T00520 1/2 .031 ● ● ●SNG 432 T0420 SNGN 120408 T01020 1/2 .031 ● ● ● ●SNG 432 T0425 SNGN 120408 T01025 1/2 .031 ○ ● ○ ● ○SNG 432 T0525 SNGN 120408 T01225 1/2 .031 ● ●SNG 432 T0820 SNGN 120408 T02020 1/2 .031 ○SNG 432 S0825 SNGN 120408 S02025 1/2 .031 ○SNG 432 T0825 SNGN 120408 T02025 1/2 .031 ● ■ ○SNG 433 T0220 SNGN 120412 T00520 1/2 .047 ● ● ●SNG 433 T0420 SNGN 120412 T01020 1/2 .047 ● ● ● ●SNG 433 T0425 SNGN 120412 T01025 1/2 .047 ○ ● ○ ● ○SNG 433 T0525 SNGN 120412 T01225 1/2 .047 ● ●SNG 433 T0820 SNGN 120412 T02020 1/2 .047 ● ○SNG 433 S0825 SNGN 120412 S02025 1/2 .047 ○SNG 433 T0825 SNGN 120412 T02025 1/2 .047 ■ ○SNG 433 Z0825 SNGN 120412 Z02025 1/2 .047 ●SNG 434 T0220 SNGN 120416 T00520 1/2 .063 ● ● ●SNG 434 T0420 SNGN 120416 T01020 1/2 .063 ● ● ● ●SNG 434 T0425 SNGN 120416 T01025 1/2 .063 ○ ● ● ● ○SNG 434 T0525 SNGN 120416 T01225 1/2 .063 ● ●SNG 434 T0820 SNGN 120416 T02020 1/2 .063 ●SNG 434 S0825 SNGN 120416 S02025 1/2 .063 ○SNG 434 T0825 SNGN 120416 T02025 1/2 .063 ● ■ ○SNG 435 T0420 SNGN 120420 T01020 1/2 .079 ●SNG 435 T0425 SNGN 120420 T01025 1/2 .079 ○ ○SNG 435 T0820 SNGN 120420 T02020 1/2 .079 ●SNG 435 T0825 SNGN 120420 T02025 1/2 .079 ○ ○SNG 436 T0425 SNGN 120424 T01025 1/2 .094 ○SNG 436 T0625 SNGN 120424 T01525 1/2 .094 ●SNG 436 T0820 SNGN 120424 T02020 1/2 .094 ○SNG 438 T0525 SNGN 120432 T01225 1/2 .125 ●SNG 438 S0825 SNGN 120432 S02025 1/2 .125 ●SNG 438 T0825 SNGN 120432 T02025 1/2 .125 ● ■SNG 452 T0220 SNGN 120708 T00520 1/2 .031 ●SNG 452 T0825 SNGN 120708 T02025 1/2 .031 ○ ○SNG 453 T0220 SNGN 120712 T00520 1/2 .047 ● ●SNG 453 S0825 SNGN 120712 S02025 1/2 .047 ○SNG 453 T0825 SNGN 120712 T02025 1/2 .047 ■ ●SNG 454 T0220 SNGN 120716 T00520 1/2 .063 ● ●SNG 454 Z0620 SNGN 120716 Z01520 1/2 .063 ●SNG 454 T0825 SNGN 120716 T02025 1/2 .063 ● ○ ○ ●SNG 554 T0820 SNGN 150716 T02020 5/8 .063 ●

90° 90°ICT

R

Holders ➡ F10・F11・G5SNG6 ➡ E14      

Cutters ➡ Ⅰ6・Ⅰ8・Ⅰ10 

(inch) IC TSNG 45 1/2 5/16SNG 55 5/8 5/16

Insert Item List

[ Ceram

ics ]

E14

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

SNG 632 T0820 SNGN 190408 T02020 3/4 .031 ●SNG 634 T0820 SNGN 190416 T02020 3/4 .063 ●SNG 643 T0820 SNGN 190612 T02020 3/4 .047 ●SNG 644 T0120 SNGN 190616 T00320 3/4 .063 ●SNG 644 T0220 SNGN 190616 T00520 3/4 .063 ● ● ●SNG 644 T0225 SNGN 190616 T00525 3/4 .063 ○SNG 644 T0320 SNGN 190616 T00820 3/4 .063 ●SNG 644 T0420 SNGN 190616 T01020 3/4 .063 ● ●SNG 644 Z0620 SNGN 190616 Z01520 3/4 .063 ●SNG 644 T0825 SNGN 190616 T02025 3/4 .063 ●SNG 653 T0825 SNGN 190712 T02025 3/4 .047 ●SNG 654 T0825 SNGN 190716 T02025 3/4 .063 ●SNG 656 T0120 SNGN 190724 T00320 3/4 .094 ●SNG 656 T0225 SNGN 190724 T00525 3/4 .094 ○SNG 656 T0320 SNGN 190724 T00820 3/4 .094 ●SNG 656 T0820 SNGN 190724 T02020 3/4 .094 ○

(inch) IC TSNG 63 3/4 3/16SNG 64 3/4 1/4SNG 65 3/4 5/16

SNG3 / 4 / 5 ➡ E13

90° 90°ICT

R

■ SNG6

90°90°IC

TR

■ SNGA (inch) IC TSNGA 43 1/2 3/16SNGA 54 5/8 1/4SNGA 64 3/4 1/4

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

SNGA 432 T0220 SNGA 120408 T00520 1/2 .031 ●SNGA 432 T0425 SNGA 120408 T01025 1/2 .031 ○SNGA 432 T0525 SNGA 120408 T01225 1/2 .031 ● ●SNGA 432 T0820 SNGA 120408 T02020 1/2 .031 ●SNGA 432 S0825 SNGA 120408 S02025 1/2 .031 ●SNGA 432 T0825 SNGA 120408 T02025 1/2 .031 ■SNGA 432 Z0825 SNGA 120408 Z02025 1/2 .031 ●SNGA 433 T0220 SNGA 120412 T00520 1/2 .047 ● ●SNGA 433 T0420 SNGA 120412 T01020 1/2 .047 ● ● ●SNGA 433 T0425 SNGA 120412 T01025 1/2 .047 ○SNGA 433 T0525 SNGA 120412 T01225 1/2 .047 ● ● ●SNGA 433 T0820 SNGA 120412 T02020 1/2 .047 ●SNGA 433 S0825 SNGA 120412 S02025 1/2 .047 ●SNGA 433 T0825 SNGA 120412 T02025 1/2 .047 ●SNGA 433 Z0825 SNGA 120412 Z02025 1/2 .047 ●SNGA 434 T0525 SNGA 120416 T01225 1/2 .063 ●SNGA 434 T0820 SNGA 120416 T02020 1/2 .063 ●SNGA 434 T0825 SNGA 120416 T02025 1/2 .063 ●SNGA 543 T0220 SNGA 150612 T00520 5/8 .047 ● ●SNGA 543 T0225 SNGA 150612 T00525 5/8 .047 ●SNGA 543 T0825 SNGA 150612 T02025 5/8 .047 ● ■SNGA 544 T0220 SNGA 150616 T00520 5/8 .063 ●SNGA 544 T0820 SNGA 150616 T02020 5/8 .063 ●SNGA 544 T0825 SNGA 150616 T02025 5/8 .063 ■SNGA 644 T0825 SNGA 190616 T02025 3/4 .063 ●

Holders ➡ F11・G5

Insert Item List

[ Ceram

ics ]

E15

90° 90°ICT

R

■ SNGX (inch) IC TSNGX 45 1/2 5/16SNGX 55 5/8 5/16

Holders ➡ F10・F11・G5

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

SNGX 452 T0220 DP5 SNGX 120708 T00520 DP5 1/2 .031 ●SNGX 452 T0320 DP5 SNGX 120708 T00820 DP5 1/2 .031 ●SNGX 452 T0825 DP5 SNGX 120708 T02025 DP5 1/2 .031 ●SNGX 453 T0220 DP5 SNGX 120712 T00520 DP5 1/2 .047 ●SNGX 453 T0320 DP5 SNGX 120712 T00820 DP5 1/2 .047 ●SNGX 453 T0820 DP5 SNGX 120712 T02020 DP5 1/2 .047 ●SNGX 453 T0825 DP5 SNGX 120712 T02025 DP5 1/2 .047 ● ●SNGX 454 T0425 DP5 SNGX 120716 T01025 DP5 1/2 .063 ●SNGX 454 T0820 DP5 SNGX 120716 T02020 DP5 1/2 .063 ● ●SNGX 454 S0825 DP5 SNGX 120716 S02025 DP5 1/2 .063 ●SNGX 454 T0825 DP5 SNGX 120716 T02025 DP5 1/2 .063 ● ●SNGX 552 T0320 DP5 SNGX 150708 T00820 DP5 5/8 .031 ●SNGX 553 T0220 DP5 SNGX 150712 T00520 DP5 5/8 .047 ● ●SNGX 553 T0320 DP5 SNGX 150712 T00820 DP5 5/8 .047 ●SNGX 554 T0320 DP5 SNGX 150716 T00820 DP5 5/8 .063 ●SNGX 554 T0825 DP5 SNGX 150716 T02025 DP5 5/8 .063 ●

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

SPG 322 T0425 SPGN 090308 T01025 3/8 .031 ○ ■SPG 324 S0820 SPGN 090316 S02020 3/8 .063 ●SPG 422 T0425 SPGN 120308 T01025 1/2 .031 ● ■ ● ●SPG 422 T0525 SPGN 120308 T01225 1/2 .031 ●SPG 432 T0420 SPGN 120408 T01020 1/2 .031 ●SPG 432 T0425 SPGN 120408 T01025 1/2 .031 ●SPG 433 T0420 SPGN 120412 T01020 1/2 .047 ●SPG 433 T0425 SPGN 120412 T01025 1/2 .047 ○SPG 433 T0825 SPGN 120412 T02025 1/2 .047 ●SPG 434 T0420 SPGN 120416 T01020 1/2 .063 ●SPG 434 T0425 SPGN 120416 T01025 1/2 .063 ● ■ ●SPG 434 T0820 SPGN 120416 T02020 1/2 .063 ● ●SPG 633 T0425 SPGN 190412 T01025 3/4 .047 ●SPG 634 T0420 SPGN 190416 T01020 3/4 .063 ●

90°11°

IC

TR

■ SPG (inch) IC TSPG 32 3/8 1/8SPG 42 1/2 1/8SPG 43 1/2 3/16SPG 63 3/4 3/16

Insert Item List

[ Ceram

ics ]

E16

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

TBGE 521 T0225 TBGE 060104 T00525 5/32 .016 ●TBGE 522 T0225 TBGE 060108 T00525 5/32 .031 ○

60°

IC

T

R

■ TBGE (inch) IC TTBGE 52 5/32 .063

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

TNG 221 T0225 TNGN 110304 T00525 1/4 .016 ●TNG 222 T0225 TNGN 110308 T00525 1/4 .031 ● ●TNG 321 T0425 TNGN 160304 T01025 3/8 .016 ●TNG 322 T0425 TNGN 160308 T01025 3/8 .031 ● ●TNG 322 T0525 TNGN 160308 T01225 3/8 .031 ●TNG 322 T0825 TNGN 160308 T02025 3/8 .031 ●TNG 331 T0425 TNGN 160404 T01025 3/8 .016 ●TNG 332 T0420 TNGN 160408 T01020 3/8 .031 ● ●TNG 332 T0425 TNGN 160408 T01025 3/8 .031 ○ ○ ○ ● ○TNG 332 T0525 TNGN 160408 T01225 3/8 .031 ● ● ●TNG 332 T0820 TNGN 160408 T02020 3/8 .031 ○TNG 332 S0825 TNGN 160408 S02025 3/8 .031 ○TNG 332 T0825 TNGN 160408 T02025 3/8 .031 ○TNG 333 T0420 TNGN 160412 T01020 3/8 .047 ● ● ●TNG 333 T0425 TNGN 160412 T01025 3/8 .047 ■ ■ ○ ● ● ● ○TNG 333 T0525 TNGN 160412 T01225 3/8 .047 ●TNG 333 T0820 TNGN 160412 T02020 3/8 .047 ● ●TNG 333 S0825 TNGN 160412 S02025 3/8 .047 ○TNG 333 T0825 TNGN 160412 T02025 3/8 .047 ○TNG 334 T0420 TNGN 160416 T01020 3/8 .063 ●TNG 334 T0425 TNGN 160416 T01025 3/8 .063 ● ○ ○TNG 334 T0525 TNGN 160416 T01225 3/8 .063 ●TNG 334 T0820 TNGN 160416 T02020 3/8 .063 ○TNG 334 T0825 TNGN 160416 T02025 3/8 .063 ○TNG 335 T0425 TNGN 160420 T01025 3/8 .079 ■ ○ ○TNG 335 T0820 TNGN 160420 T02020 3/8 .079 ○TNG 352 T0825 TNGN 160708 T02025 3/8 .031 ○TNG 353 T0825 TNGN 160712 T02025 3/8 .047 ○

60°

90°IC

T

R

■ TNG2 / TNG3 (inch) IC TTNG 22 1/4 1/8TNG 32 3/8 1/8TNG 33 3/8 3/16TNG 35 3/8 5/16

TNG4 / 5 ➡ E17

Holders ➡ F14

Insert Item List

[ Ceram

ics ]

E17

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

TNG 431 T0425 TNGN 220404 T01025 1/2 .016 ●TNG 432 T0220 TNGN 220408 T00520 1/2 .031 ● ● ●TNG 432 T0420 TNGN 220408 T01020 1/2 .031 ● ●TNG 432 T0425 TNGN 220408 T01025 1/2 .031 ●TNG 432 T0525 TNGN 220408 T01225 1/2 .031 ●TNG 432 T0820 TNGN 160408 T02020 1/2 .031 ●TNG 432 T0825 TNGN 220408 T02025 1/2 .031 ■ ■TNG 432 Z0825 TNGN 220408 Z02025 1/2 .031 ●TNG 433 T0220 TNGN 220412 T00520 1/2 .047 ● ●TNG 433 T0225 TNGN 220412 T00525 1/2 .047 ●TNG 433 T0425 TNGN 220412 T01025 1/2 .047 ●TNG 433 T0630 TNGN 220412 T01530 1/2 .047 ●TNG 433 Z0820 TNGN 220412 Z02020 1/2 .047 ●TNG 433 T0825 TNGN 220412 T02025 1/2 .047 ■TNG 433 Z0825 TNGN 220412 Z02025 1/2 .047 ● ●TNG 434 T0220 TNGN 220416 T00520 1/2 .063 ● ●TNG 434 T0625 TNGN 220416 T01525 1/2 .063 ●TNG 434 T0825 TNGN 220416 T02025 1/2 .063 ■ ■TNG 452 T0220 TNGN 220708 T00520 1/2 .031 ●TNG 452 T0825 TNGN 220708 T02025 1/2 .031 ●TNG 453 T0220 TNGN 220712 T00520 1/2 .047 ● ●TNG 454 T0825 TNGN 220716 T02025 1/2 .063 ●TNG 543 T0825 TNGN 270612 T02025 5/8 .047 ●TNG 544 T0120 TNGN 270616 T00320 5/8 .063 ●TNG 544 T0220 TNGN 270616 T00520 5/8 .063 ●TNG 544 T0825 TNGN 270616 T02025 5/8 .063 ●

(inch) IC TTNG 43 1/2 3/16TNG 45 1/2 5/16TNG 54 5/8 1/4

60°

90°ICT

R

■ TNG4 / TNG5

TNG2 / 3 ➡ E16

Insert Item List

[ Ceram

ics ]

E18

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

■ TNGA (inch) IC TTNGA 43 1/2 3/16

60°

90°ICT

R

Holders ➡ F14・J34

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

TNGA 321 T0425 TNGA 160304 T01025 3/8 .016 ●TNGA 322 T0525 TNGA 160308 T01225 3/8 .031 ●TNGA 331 T0425 TNGA 160404 T01025 3/8 .016 ● ○TNGA 331 S0825 TNGA 160404 S02025 3/8 .016 ●TNGA 331 Z0825 TNGA 160404 Z02025 3/8 .016 ●TNGA 332 T0425 TNGA 160408 T01025 3/8 .031 ● ■ ○ ○ ○TNGA 332 T0525 TNGA 160408 T01225 3/8 .031 ● ● ●TNGA 332 T0820 TNGA 160408 T02020 3/8 .031 ●TNGA 332 S0825 TNGA 160408 S02025 3/8 .031 ●TNGA 332 T0825 TNGA 160412 T02025 3/8 .031 ○TNGA 332 Z0825 TNGA 160408 Z02025 3/8 .031 ●TNGA 333 T0425 TNGA 160412 T01025 3/8 .047 ● ■ ● ○ ○TNGA 333 T0525 TNGA 160412 T01225 3/8 .047 ●TNGA 333 T0820 TNGA 160412 T02020 3/8 .047 ●TNGA 333 S0825 TNGA 160412 S02025 3/8 .047 ●TNGA 333 T0825 TNGA 160412 T02025 3/8 .047 ○TNGA 333 Z0825 TNGA 160412 Z02025 3/8 .047 ●TNGA 334 T0825 TNGA 160416 T02025 3/8 .063 ○TNGA 431 T0425 TNGA 220404 T01025 1/2 .016 ●TNGA 432 T0220 TNGA 220408 T00520 1/2 .031 ●TNGA 432 T0525 TNGA 160408 T01225 1/2 .031 ●TNGA 432 S0825 TNGA 220408 S02025 1/2 .031 ●TNGA 432 T0825 TNGA 220408 T02025 1/2 .031 ● ■ ● ●TNGA 433 T0825 TNGA 220412 T02025 1/2 .047 ● ■ ●TNGA 433 Z0825 TNGA 220412 Z02025 1/2 .047 ●TNGA 434 T0525 TNGA 220416 T01225 1/2 .063 ●TNGA 434 T0825 TNGA 220416 T02025 1/2 .063 ● ●

60°

90°IC

T

R

■ TNGG with chip-breaker (inch) IC TTNGG 33 3/8 .063

Holders ➡ F14・J34

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

TNGG 332 Z0430 AG TNGG 160408 Z01030 AG 3/8 .031 ●TNGG 333 Z0430 AG TNGG 160412 Z01030 AG 3/8 .047 ●

(inch) IC TTNGA 32 3/8 1/8TNGA 33 3/8 3/16

Insert Item List

[ Ceram

ics ]

E19

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

TP 41 T0225 1/4 .016 ●TP 42 T0225 1/4 .031 ●

■ TP (inch) IC TTP 41 1/4 .094TP 42 1/4 .094

60°

10°

IC

T

R

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

TPG 221 T0225 TPGN 110304 T00525 1/4 .016 ●TPG 221 T0425 TPGN 110304 T01025 1/4 .016 ○TPG 221 T0525 TPGN 110304 T01225 1/4 .016 ●TPG 222 T0225 TPGN 110308 T00525 1/4 .031 ● ●TPG 222 T0425 TPGN 110308 T01025 1/4 .031 ○TPG 222 T0525 TPGN 110308 T01225 1/4 .031 ●TPG 222 T0825 TPGN 110308 T02025 1/4 .031 ●TPG 223 T0225 TPGN 110312 T00525 1/4 .047 ●TPG 223 T0820 TPGN 110312 T02020 1/4 .047 ●TPG 32Y T0425 TPGN 160302 T01025 3/8 .008 ●TPG 321 T0425 TPGN 160304 T01025 3/8 .016 ● ○TPG 321 T0525 TPGN 160304 T01225 3/8 .016 ●TPG 322 T0220 TPGN 160308 T00520 3/8 .031 ● ●TPG 322 T0425 TPGN 160308 T01025 3/8 .031 ● ○ ● ○TPG 322 T0525 TPGN 160308 T01225 3/8 .031 ● ●TPG 323 T0220 TPGN 160312 T00520 3/8 .047 ● ●TPG 323 T0425 TPGN 160312 T01025 3/8 .047 ●TPG 323 T0525 TPGN 160312 T01225 3/8 .047 ●TPG 324 T0425 TPGN 160316 T01025 3/8 .063 ●TPG 431 T0425 TPGN 220404 T01025 1/2 .016 ●TPG 432 T0220 TPGN 220408 T00520 1/2 .031 ●TPG 432 T0425 TPGN 220408 T01025 1/2 .031 ● ● ●TPG 432 T0525 TPGN 220408 T01225 1/2 .031 ●TPG 433 T0220 TPGN 220412 T00520 1/2 .047 ●TPG 434 T0220 TPGN 220416 T00520 1/2 .063 ●TPG 434 T0425 TPGN 220416 T01025 1/2 .063 ●TPGE 521 T0225 TPGN 060104 T00525 5/32 .016 ●TPGE 731 T0225 TPGN 090204 T00525 7/32 .016 ●TPGE 732 T0225 TPGN 090208 T00525 7/32 .031 ●

■ TPG / TPGE (inch) IC TTPG 22 1/4 1/8TPG 32 3/8 1/8TPG 43 1/2 3/16

60°

11°

IC

T

R

(inch) IC TTPGE 52 5/32 .063TPGE 73 7/32 .094

Insert Item List

[ Ceram

ics ]

E20

Ceramics

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

VNG 331 T0425 VNGN 160404 T01025 3/8 .016 ●VNG 332 T0425 VNGN 160408 T01025 3/8 .031 ●

■ VNG (inch) IC TVNG 33 3/8 3/16

90°

35°

ICT

R

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

VNGA 331 T0220 VNGA 160404 T00520 3/8 .016 ●VNGA 331 T0225 VNGA 160404 T00525 3/8 .016 ●VNGA 331 T0420 VNGA 160404 T01020 3/8 .016 ○VNGA 331 T0425 VNGA 160404 T01025 3/8 .016 ● ○ ○VNGA 331 T0525 VNGA 160404 T01225 3/8 .016 ● ●VNGA 331 S0825 VNGA 160404 S02025 3/8 .016 ●VNGA 331 Z0825 VNGA 160404 Z02025 3/8 .016 ●VNGA 332 T0220 VNGA 160408 T00520 3/8 .031 ● ●VNGA 332 T0320 VNGA 160408 T00820 3/8 .031 ●VNGA 332 T0420 VNGA 160408 T01020 3/8 .031 ● ●VNGA 332 T0425 VNGA 160408 T01025 3/8 .031 ● ● ○ ○VNGA 332 T0525 VNGA 160408 T01225 3/8 .031 ● ●VNGA 332 S0825 VNGA 160408 S02025 3/8 .031 ●VNGA 332 Z0825 VNGA 160408 Z02025 3/8 .031 ●VNGA 333 T0220 VNGA 160412 T00520 3/8 .047 ●VNGA 333 T0320 VNGA 160412 T00820 3/8 .047 ●VNGA 333 T0420 VNGA 160412 T01020 3/8 .047 ● ●VNGA 333 T0425 VNGA 160412 T01025 3/8 .047 ● ● ● ○VNGA 333 S0825 VNGA 160412 S02025 3/8 .047 ●VNGA 333 T0825 VNGA 160412 T02025 3/8 .047 ■VNGA 333 Z0825 VNGA 160412 Z02025 3/8 .047 ●VNGA 431 T0425 VNGA 220404 T01025 1/2 .016 ●VNGA 432 T0425 VNGA 220408 T01025 1/2 .031 ●VNGA 433 T0425 VNGA 220412 T01025 1/2 .047 ●VNGA 436 T0420 VNGA 220424 T01020 1/2 .094 ●

■ VNGA (inch) IC TVNGA 33 3/8 3/16VNGA 43 1/2 3/16

Holders ➡ F12・F13

35°

90°

IC

TR

Insert Item List

[ Ceram

ics ]

E21

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number ISO Item Number IC RSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

WNGA 331 T0525 WNGA 060404 T01225 3/8 .016 ●WNGA 332 T0525 WNGA 060408 T01225 3/8 .031 ●WNGA 333 T0525 WNGA 060412 T01225 3/8 .047 ●WNGA 431 T0220 WNGA 080404 T00520 1/2 .016 ●WNGA 431 Z0825 WNGA 080404 Z02025 1/2 .016 ●WNGA 432 T0220 WNGA 080408 T00520 1/2 .031 ● ● ●WNGA 432 T0420 WNGA 080408 T01020 1/2 .031 ●WNGA 432 T0525 WNGA 080408 T01225 1/2 .031 ● ●WNGA 432 T0820 WNGA 080408 T02020 1/2 .031 ● ●WNGA 432 T0825 WNGA 080408 T02025 1/2 .031 ■WNGA 432 Z0825 WNGA 080408 Z02025 1/2 .031 ●WNGA 433 T0220 WNGA 080412 T00520 1/2 .047 ● ● ●WNGA 433 T0420 WNGA 080412 T01020 1/2 .047 ●WNGA 433 T0525 WNGA 080412 T01225 1/2 .047 ●WNGA 433 T0820 WNGA 080412 T02020 1/2 .047 ● ●WNGA 433 T0825 WNGA 080412 T02025 1/2 .047 ■ ■WNGA 434 T0420 WNGA 080416 T01020 1/2 .063 ●WNGA 434 T0820 WNGA 080416 T02020 1/2 .063 ●WNGA 434 T0825 WNGA 080416 T02025 1/2 .063 ■

80°

I.C.

T

R

■ WNGA (inch) IC TWNGA 33 3/8 3/16WNGA 43 1/2 3/16WNGA 54 5/8 1/4

Holders ➡ F15・G5

Insert Item List

[ Ceram

ics ]

E22

CBN / PCD

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

CCGW 21.51 PD CCGW 060204 PD S0415 1/4 .016 2 ●CCGW 32.508 PD CCGW 09T302 PD S0415 3/8 .008 2 ●CCGW 32.508 PD CCGW 09T302 PD S0635 3/8 .008 2 ●CCGW 32.51 PD CCGW 09T304 PD S0415 3/8 .016 2 ●CCGW 32.51 PD CCGW 09T304 PD S0635 3/8 .016 2 ●CCGW 32.52 PD CCGW 09T308 PD S0415 3/8 .031 2 ●CCGW 32.52 PD CCGW 09T308 PD S0635 3/8 .031 2 ●CCMW 32.504 CCMW 09T301 None 3/8 .004 1 ○CCMW 32.508 CCMW 09T302 None 3/8 .008 1 ○CCMW 32.51 CCMW 09T304 None 3/8 .016 1 ○CCMW 32.52 CCMW 09T308 None 3/8 .031 1 ○

■ CC. W (inch) IC TCC.. 21 1/4 .094CC.. 32 3/8 5/32

Holders ➡ J26・J27・J108

100°

80° 7°

IC

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

CNGA 4308 PQ CNGA 120402 PQ S0415 1/2 .008 4 ●CNGA 4308 PQ CNGA 120402 PQ S0635 1/2 .008 4 ●CNGA 431 PQ CNGA 120404 PQ S0415 1/2 .016 4 ●CNGA 431 PQ CNGA 120404 PQ S0420 1/2 .016 4 ○CNGA 431 PQ CNGA 120404 PQ T0420 1/2 .016 4 ○CNGA 431 PQ CNGA 120404 PQ S0525 1/2 .016 4 ○CNGA 431 PQ CNGA 120404 PQ S0635 1/2 .016 4 ●CNGA 432 PQ CNGA 120408 PQ S0415 1/2 .031 4 ●CNGA 432 PQ CNGA 120408 PQ S0420 1/2 .031 4 ○CNGA 432 PQ CNGA 120408 PQ T0420 1/2 .031 4 ○CNGA 432 PQ CNGA 120408 PQ S0525 1/2 .031 4 ○CNGA 432 PQ CNGA 120408 PQ S0635 1/2 .031 4 ●CNGA 433 PQ CNGA 120412 PQ S0415 1/2 .047 4 ●CNGA 433 PQ CNGA 120412 PQ S0420 1/2 .047 4 ○CNGA 433 PQ CNGA 120412 PQ T0420 1/2 .047 4 ○CNMA 433 PQ CNMA 120412 PQ S0525 1/2 .047 4 ○CNGA 433 PQ CNGA 120412 PQ S0635 1/2 .047 4 ●

with wiper

CNGA 431 PQW CNGA 120404 PQW S0415 1/2 .016 4 ●CNGA 431 PQW CNGA 120404 PQW S0635 1/2 .016 4 ●CNGA 432 PQW CNGA 120408 PQW S0415 1/2 .031 4 ●CNGA 432 PQW CNGA 120408 PQW S0635 1/2 .031 4 ●CNGA 433 PQW CNGA 120412 PQW S0415 1/2 .047 4 ●CNGA 433 PQW CNGA 120412 PQW S0635 1/2 .047 4 ●

■ CN. A 43 (inch) IC TCN.. 43 1/2 3/16

Holders ➡ F6・F7・G4・J35

100°

80°

90°

IC

Insert Item List

[ CBN

/ PCD ]

E23

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

DCGW 21.508 PD DCGW 070202 PD S0415 1/4 .008 2 ●DCGW 21.51 PD DCGW 070204 PD S0415 1/4 .016 2 ●DCGW 21.51 PD DCGW 070204 PD S0635 1/4 .016 2 ●DCGW 21.52 PD DCGW 070208 PD S0415 1/4 .031 2 ●DCGW 32.508 PD DCGW 11T302 PD S0415 3/8 .008 2 ●DCGW 32.508 PD DCGW 11T302 PD S0635 3/8 .008 2 ●DCGW 32.51 PD DCGW 11T304 PD S0415 3/8 .016 2 ●DCGW 32.51 PD DCGW 11T304 PD S0635 3/8 .016 2 ●DCGW 32.52 PD DCGW 11T308 PD S0415 3/8 .031 2 ●DCGW 32.52 PD DCGW 11T308 PD S0635 3/8 .031 2 ●DCMW 32.504 DCMW 11T301 None 3/8 .004 1 ○

DCMW 32.508 DCMW 11T302 None 3/8 .008 1 ●

DCMW 32.51 DCMW 11T304 None 3/8 .016 1 ○

DCMW 32.52 DCMW 11T308 None 3/8 .031 1 ○

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

DNGA 4308 PQ DNGA 150402 PQ S0415 1/2 .008 4 ●DNGA 4308 PQ DNGA 150402 PQ S0635 1/2 .008 4 ●DNGA 431 PQ DNGA 150404 PQ S0415 1/2 .016 4 ●DNGA 431 PQ DNGA 150404 PQ S0525 1/2 .016 4 ○DNGA 431 PQ DNGA 150404 PQ S0635 1/2 .016 4 ●DNGA 432 PQ DNGA 150408 PQ S0415 1/2 .031 4 ●DNGA 432 PQ DNGA 150408 PQ S0420 1/2 .031 4 ○DNGA 432 PQ DNGA 150408 PQ T0420 1/2 .031 4 ○DNGA 432 PQ DNGA 150408 PQ S0525 1/2 .031 4 ○DNGA 432 PQ DNGA 150408 PQ S0635 1/2 .031 4 ●DNGA 433 PQ DNGA 150412 PQ S0415 1/2 .047 4 ●DNGA 433 PQ DNGA 150412 PQ S0420 1/2 .047 4 ○DNGA 433 PQ DNGA 150412 PQ T0420 1/2 .047 4 ○DNMA 433 PQ DNMA 150412 PQ S0525 1/2 .047 4 ●DNGA 433 PQ DNGA 150412 PQ S0635 1/2 .047 4 ●

(inch) IC TDC.. 21 1/4 .094DC.. 32 3/8 5/32

(inch) IC TDN.. 43 1/2 3/16

Holders ➡ J28・J29・J30

Holders ➡ F8・F9・G4

■ DC. W

■ DN. A 43

55° 7°

IC

55°

90°

RT

IC

Insert Item List

[ CBN

/ PCD ]

E24

CBN / PCD

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

SNGA 431 PE SNGA 120404 PE T0420 1/2 .016 8 ○SNGA 431 PE SNGA 120404 PE S0635 1/2 .016 8 ○SNGA 432 PE SNGA 120408 PE S0415 1/2 .031 8 ○SNGA 432 PE SNGA 120408 PE S0525 1/2 .031 8 ○SNGA 432 PE SNGA 120408 PE S0635 1/2 .031 8 ○SNGA 433 PE SNGA 120412 PE S0415 1/2 .047 8 ○SNGA 433 PE SNGA 120412 PE S0420 1/2 .047 8 ○SNGA 433 PE SNGA 120412 PE T0420 1/2 .047 8 ○SNMA 433 PE SNMA 120412 PE S0525 1/2 .047 8 ●SNGA 433 PE SNGA 120412 PE S0635 1/2 .047 8 ○

(inch) IC TSN.. 43 1/2 3/16

Holders ➡ F11・G5

■ SN. A 43

90° 90°

RT

IC

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

SPG 321 PQ SPGN 090304 PQ S0420 3/8 .016 4 ○

SPG 322 PQ SPGN 090308 PQ S0420 3/8 .031 4 ○

SPG 322 PQ SPGN 090308 PQ T0420 3/8 .031 4 ○

(inch) IC TSP.. 32 3/8 1/8

■ SPG 32

90°11°

RT

IC

Insert Item List

[ CBN

/ PCD ]

E25

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

TPG 221 PT TPGN 110304 PT S0420 1/4 .016 3 ○

TPG 222 PT TPGN 110308 PT S0420 1/4 .031 3 ○

TPG 321 PT TPGN 160304 PT S0420 .094 .016 3 ○

TPG 322 PT TPGN 160308 PT S0420 .094 .031 3 ○TPGW 2208 PT TPGW 110302 PT S0415 1/4 .008 3 ○TPGW 221 PT TPGW 110304 PT S0415 1/4 .016 3 ○TPGW 221 PT TPGW 110304 PT T0615 1/4 .016 3 ○TPGW 221 PT TPGW 110304 PT S0635 1/4 .016 3 ○TPGW 222 PT TPGW 110308 PT S0415 1/4 .031 3 ○TPGW 222 PT TPGW 110308 PT S0635 1/4 .031 3 ○

(inch) IC TTP.. 22 1/4 1/8TP.. 32 .094 1/8

Holders(TPGW) ➡ J109

■ TPG

60°

11°R

IC

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

TNGA 331C PH TNGA 160401 PH S0415 3/8 .004 6 ●TNGA 3308 PH TNGA 160402 PH S0415 3/8 .008 6 ●TNGA 3308 PH TNGA 160402 PH S0635 3/8 .008 6 ●TNGA 331 PH TNGA 160404 PH S0415 3/8 .016 6 ●TNGA 331 PH TNGA 160404 PH T0420 3/8 .016 6 ○TNGA 331 PH TNGA 160404 PH S0525 3/8 .016 6 ○TNGA 331 PH TNGA 160404 PH S0635 3/8 .016 6 ●TNGA 332 PH TNGA 160408 PH S0415 3/8 .031 6 ●TNGA 332 PH TNGA 160408 PH S0420 3/8 .031 6 ○TNGA 332 PH TNGA 160408 PH T0420 3/8 .031 6 ○TNGA 332 PH TNGA 160408 PH S0525 3/8 .031 6 ○TNGA 332 PH TNGA 160408 PH S0635 3/8 .031 6 ●TNGA 333 PH TNGA 160412 PH S0415 3/8 .047 6 ●TNGA 333 PH TNGA 160412 PH S0420 3/8 .047 6 ○TNGA 333 PH TNGA 160412 PH T0420 3/8 .047 6 ○TNMA 333 PH TNMA 160412 PH S0525 3/8 .047 6 ○TNGA 333 PH TNGA 160412 PH S0635 3/8 .047 6 ●

(inch) IC TTN.. 33 3/8 1/8

Holders ➡ F14・J34

■ TN. A 3360°

90°

IC

Insert Item List

[ CBN

/ PCD ]

E26

CBN / PCD

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

VBGW 2208 PD VBGW 110302 PD S0415 1/4 .008 2 ○VBGW 221 PD VBGW 110304 PD S0415 1/4 .016 2 ○VBGW 332 PD VBGW 160408 PD S0415 3/8 .031 2 ○VCGW 221 PD VCGW 110304 PD S0415 1/4 .016 2 ○VCGW 221 PD VCGW 110304 PD S0635 1/4 .016 2 ○VCGW 222 PD VCGW 110308 PD S0415 1/4 .031 2 ○VCGW 222 PD VCGW 110308 PD S0635 1/4 .031 2 ○VCGW 331 PD VCGW 160404 PD S0415 3/8 .016 2 ○VCGW 331 PD VCGW 160404 PD S0635 3/8 .016 2 ○VCGW 332 PD VCGW 160408 PD S0415 3/8 .031 2 ○VCGW 332 PD VCGW 160408 PD S0635 3/8 .031 2 ○VCMW 2204 VCMW 110301 None 1/4 .004 1 ○VCMW 2208 VCMW 110302 None 1/4 .008 1 ○VCMW 221 VCMW 110304 None 1/4 .016 1 ○

Steel PStainless Steel MCast Iron K ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy SHardened Material H ● ● ●

Shape Item Number ISO Item Number Edge Prep. IC R No. of edgeCBN PCD

B23

B30

B36

B40

B52

PD1

VNGA 3308 PQ VNGA 160402 PQ S0635 3/8 .008 4 ●VNGA 331 PQ VNGA 160404 PQ S0415 3/8 .016 4 ●VNGA 331 PQ VNGA 160404 PQ S0525 3/8 .016 4 ○VNGA 331 PQ VNGA 160404 PQ S0635 3/8 .016 4 ●VNGA 331 PQ VNGA 160404 PQ T01020 3/8 .016 4 ○VNGA 332 PQ VNGA 160408 PQ S0415 3/8 .031 4 ●VNGA 332 PQ VNGA 160408 PQ S0525 3/8 .031 4 ○VNGA 332 PQ VNGA 160408 PQ S0635 3/8 .031 4 ●VNGA 333 PQ VNGA 160412 PQ S0635 3/8 .047 4 ●

(inch) IC TVB.. 22 1/4 1/8VB.. 33 3/8 3/16VC.. 22 1/4 1/8VC.. 33 3/8 3/16

(inch) IC TVN.. 33 3/8 3/16

VCGW ➡ J31

Holders ➡ F12・F13

■ VB / VC

■ VNGA 33

35°5°

RT

IC

35°7°

RT

IC

VB.. VC..

90°

35°

IC

Insert Item List

[ CBN

/ PCD ]

E27

RT

R

IC

7°80°

100°Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

CCGT 21.508 FN1L CCGT 060202 FN1L 1/4 .008 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 32.51 FN1L CCGT 09T304 FN1L 3/8 .016 ○

CCGT 21.504 AF1 CCGT 060201 ENBAF1 1/4 .004 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 21.508 AF1 CCGT 060202 ENBAF1 1/4 .008 ●CCGT 21.51 AF1 CCGT 060204 ENBAF1 1/4 .016 ●CCGT 21.51 FNAF1 CCGT 060204 FNAF1 1/4 .016 ●CCGT 21.52 AF1 CCGT 060208 ENBAF1 1/4 .031 ●CCGT 32.508 AF1 CCGT 09T302 ENBAF1 3/8 .008 ○CCGT 32.508 FNAF1 CCGT 09T302 FNAF1 3/8 .008 ●CCGT 32.51 FNAF1 CCGT 09T304 FNAF1 3/8 .016 ●CCGT 32.51 AF1 CCGT 09T304 ENBAF1 3/8 .016 ○CCGT 32.52 FNAF1 CCGT 09T308 FNAF1 3/8 .031 ●CCGT 32.52 AF1 CCGT 09T308 ENBAF1 3/8 .031 ○CCGT 21.501 FNAM3 CCGT 060200 FNAM3 1/4 .001 ○ ● ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 21.504M FNAM3 CCGT 060201M FNAM3 1/4 .003 ●CCGT 21.504 FNAM3 CCGT 060201 FNXAM3 1/4 .004 ●CCGT 21.508M FNAM3 CCGT 060202M FNAM3 1/4 .007 ○ ●CCGT 21.508 FNAM3 CCGT 060202 FNAM3 1/4 .008 ○ ○CCGT 21.508 FNAM3 CCGT 060202 FNXAM3 1/4 .008 ●CCGT 21.51M FNAM3 CCGT 060204M FNAM3 1/4 .015 ○ ●CCGT 21.51 FNAM3 CCGT 060204 FNAM3 1/4 .016 ● ○CCGT 32.501 FNAM3 CCGT 09T300 FNAM3 3/8 .001 ● ● ● ○CCGT 32.504M FNAM3 CCGT 09T301M FNAM3 3/8 .003 ● ● ● ● ○CCGT 32.504 FNAM3 CCGT 09T301 FNXAM3 3/8 .004 ●CCGT 32.508M FNAM3 CCGT 09T302M FNAM3 3/8 .007 ● ● ● ● ○CCGT 32.508 FNAM3 CCGT 09T302 FNAM3 3/8 .008 ● ○CCGT 32.508 FNAM3 CCGT 09T302 FNXAM3 3/8 .008 ●CCGT 32.51M FNAM3 CCGT 09T304M FNAM3 3/8 .015 ○ ● ● ○ ○CCGT 32.51 FNAM3 CCGT 09T304 FNAM3 3/8 .016 ● ○CCGT 32.51 FNAM3 CCGT 09T304 FNXAM3 3/8 .016 ●CCGT 32.52 FNAM3 CCGT 09T308 FNAM3 3/8 .031 ● ●CCMT 21.508 AM3 CCMT 060202 ENBAM3 1/4 .008 ○ ○CCMT 21.51 AM3 CCMT 060204 ENBAM3 1/4 .016 ● ○CCMT 32.508 AM3 CCMT 09T302 ENBAM3 3/8 .008 ○ ○CCMT 32.51 AM3 CCMT 09T304 ENBAM3 3/8 .016 ● ○CCMT 32.52 AM3 CCMT 09T308 ENBAM3 3/8 .031 ● ○CCMT 32.53 AM3 CCMT 09T312 ENBAM3 3/8 .047 ○ ○CCMT 21.51 AM5 CCMT 060204 ENBAM5 1/4 .016 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCMT 32.51 AM5 CCMT 09T304 ENBAM5 3/8 .016 ●

CCMT 32.52 AM5 CCMT 09T308 ENBAM5 3/8 .031 ●

CCGT 21.501 FNAZ7 CCGT 060200 FNAZ7 1/4 .001 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 21.504M FNAZ7 CCGT 060201M FNAZ7 1/4 .003 ○CCGT 21.508M FNAZ7 CCGT 060202M FNAZ7 1/4 .007 ○CCGT 32.501 FNAZ7 CCGT 09T300 FNAZ7 3/8 .001 ○ ○ ○ ○ ○CCGT 32.504M FNAZ7 CCGT 09T301M FNAZ7 3/8 .003 ○ ○ ● ○ ○CCGT 32.508M FNAZ7 CCGT 09T302M FNAZ7 3/8 .007 ○ ○ ○ ○ ○CCGT 32.51M FNAZ7 CCGT 09T304M FNAZ7 3/8 .015 ○ ○ ● ○ ○

■ 80 degree Diamond Positive type(CC..) (inch) IC TCC..21.5 1/4 3/32CC..32.5 3/8 5/32

Carbide / Cermet

Holders ➡ J26・J27・J108

Insert Item List

[ Carbide

/ Cermet ]

E28

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)  M:Mirror finish

RT

R

IC

7°80°

100°Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

CCGT 21.504M CL CCGT 060201M CL 1/4 .003 ○ ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 21.508M CL CCGT 060202M CL 1/4 .007 ○ ○CCGT 32.504M CL CCGT 09T301M CL 3/8 .003 ● ●CCGT 32.508M CL CCGT 09T302M CL 3/8 .007 ● ●CCGT 32.51M CL CCGT 09T304M CL 3/8 .015 ● ●CCGT 21.508 F F1 CCGT 060202 F F1 1/4 .008 Ⓡ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 21.51 F F1 CCGT 060204 F F1 1/4 .016 ⓇCCGT 32.508 F F1 CCGT 09T302 F F1 3/8 .008 ⓇCCGT 32.51 F F1 CCGT 09T304 F F1 3/8 .016 Ⓡ

CCGT 21.508 ENBFM CCGT 060202 ENBFM 1/4 .008 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 21.51 ENBFM CCGT 060204 ENBFM 1/4 .016 ○

CCET 21.502 KHG CCET 0602005 KHG 1/4 .002 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCET 21.503 KHG CCET 0602008 KHG 1/4 .003 ○CCET 21.507 KHG CCET 0602018 KHG 1/4 .007 ○CCET 21.508 KHG CCET 060202 KHG 1/4 .008 ○CCET 32.502 KHG CCET 09T3005 KHG 3/8 .002 Ⓡ ○CCET 32.503 KHG CCET 09T3008 KHG 3/8 .003 Ⓡ ○CCET 32.507 KHG CCET 09T3018 KHG 3/8 .007 Ⓡ ○CCET 32.508 KHG CCET 09T302 KHG 3/8 .008 Ⓡ ○CCMT 21.508 QD CCMT 060202 ENAQD 1/4 .008 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCMT 21.51 QD CCMT 060204 ENAQD 1/4 .016 ○CCMT 32.508 QD CCMT 09T302 ENAQD 3/8 .008 ○CCMT 32.51 QD CCMT 09T304 ENAQD 3/8 .016 ○CCMT 32.52 QD CCMT 09T308 ENAQD 3/8 .031 ○CCGT 21.501 S CCGT 060200 S 1/4 .001 Ⓡ R ○ LⓇ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 21.504M S CCGT 060201M S 1/4 .003 Ⓡ RCCGT 21.504 S CCGT 060201 S 1/4 .004 ○ ○ ⓁRCCGT 21.508M S CCGT 060202M S 1/4 .007 RCCGT 21.508 S CCGT 060202 S 1/4 .008 ○ Ⓡ ⓁR ○CCGT 21.51 S CCGT 060204 S 1/4 .016 RCCGT 32.501 S CCGT 09T300 S 3/8 .001 R R R ○ ⓇCCGT 32.504M S CCGT 09T301M S 3/8 .003 R R ⓇCCGT 32.504 S CCGT 09T301 S 3/8 .004 R ○ ○CCGT 32.508M S CCGT 09T302M S 3/8 .007 R R ⓇCCGT 32.508 S CCGT 09T302 S 3/8 .008 R ⓁR ⓇCCGT 32.51M S CCGT 09T304M S 3/8 .015 R ⓇCCGT 32.51 S CCGT 09T304 S 3/8 .016 RCCMT 21.504 T AS CCMT 060201 T AS 1/4 .004 ○ ○CCMT 21.508 T AS CCMT 060202 T AS 1/4 .008 ○ ○CCMT 21.51 T AS CCMT 060204 T AS 1/4 .016 ○ ○CCMT 32.504 T AS CCMT 09T301 T AS 3/8 .004 ○ ○CCMT 32.508 T AS CCMT 09T302 T AS 3/8 .008 ○ ○CCMT 32.51 T AS CCMT 09T304 T AS 3/8 .016 ○ ○

■ 80 degree Diamond Positive type(CC.. ,continued) (inch) IC TCC..21.5 1/4 3/32CC..32.5 3/8 5/32

Holders ➡ J26・J27・J108

Insert Item List

[ Carbide

/ Cermet ]

E29

RT

RIC

7°80°

100°Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

CCGT 21.501 U CCGT 060200 U 1/4 .001 Ⓡ Ⓡ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCGT 21.504 U CCGT 060201 U 1/4 .004 Ⓡ ○CCGT 21.508 U CCGT 060202 U 1/4 .008 Ⓡ ○CCGT 32.501 U1 CCGT 09T300 U1 3/8 .001 R ○CCGT 32.504 U1 CCGT 09T301 U1 3/8 .004 Ⓡ R ○CCGT 32.508 U1 CCGT 09T302 U1 3/8 .008 Ⓡ R ○CCGT 32.51 U1 CCGT 09T304 U1 3/8 .016 Ⓡ ○CCMT 21.508 ENBZR CCMT 060202 ENBZR 1/4 .008 ○ ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CCMT 21.51 ENBZR CCMT 060204 ENBZR 1/4 .016 ○ ○CCMT 32.508 ENBZR CCMT 09T302 ENBZR 3/8 .008 ○ ○CCMT 32.51 ENBZR CCMT 09T304 ENBZR 3/8 .016 ○ ○CCMT 32.52 ENBZR CCMT 09T308 ENBZR 3/8 .031 ○ ○CCGW 21.501 FN CCGW 060200 FN 1/4 .001 ○

CCGW 21.501 H CCGW 060200 H 1/4 .001 ○CCGW 21.504 FN CCGW 060201 FN 1/4 .004 ○CCGW 21.504 H CCGW 060201 H 1/4 .004 ○CCGW 21.508 H CCGW 060202 H 1/4 .008 ○CCGW 21.52 FN CCGW 060208 FN 1/4 .031 ●CCGW 32.500 V CCGW 09T30 V 3/8 0 ○CCGW 32.501 FN CCGW 09T300 FN 3/8 .001 ○CCGW 32.501 H CCGW 09T300 H 3/8 .001 ○CCGW 32.504 FN CCGW 09T301 FN 3/8 .004 ○CCGW 32.504 H CCGW 09T301 H 3/8 .004 ○CCGW 32.504 D CCGW 09T301 P 3/8 .004 ○CCGW 32.508M P CCGW 09T302M P 3/8 .007 ○CCGW 32.508 H CCGW 09T302 H 3/8 .008 ○CCGW 32.508 P CCGW 09T302 P 3/8 .008 ○

Holders ➡ J26・J27・J108

M

MM

M

M

MMMMM

Insert Item List

[ Carbide

/ Cermet ]

E30

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

RT

R

IC 90°

80°

100°Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

CNMG 432 G CNMG 120408 G 1/2 .031 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNMG 433 G CNMG 120412 G 1/2 .047 ○

CNMG 434 G CNMG 120416 G 1/2 .063 ○CNMG 431 G CNMG 120404 ENBG 1/2 .016 ● ●CNMG 431 TNG CNMG 120404 TNG 1/2 .016 ○CNMG 432 G CNMG 120408 ENBG 1/2 .031 ● ○CNMG 432 TNG CNMG 120408 TNG 1/2 .031 ○CNMG 433 G CNMG 120412 ENBG 1/2 .047 ● ●CNMG 433 TNG CNMG 120412 TNG 1/2 .047 ○CNGG 4304 N1 CNGG 120401 N1 1/2 .004 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNGG 4308 N1 CNGG 120402 N1 1/2 .008 RCNGG 431 N1 CNGG 120404 N1 1/2 .016 ●CNGG 432 N1 CNGG 120408 N1 1/2 .031 ●

CNMG 431 WM CNMG 120404 ENWM 1/2 .016 ● ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNMG 432 WM CNMG 120408 ENWM 1/2 .031 ● ○

CNMG 432 WR CNMG 120408 ENBWR 1/2 .031 ●.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNMG 432 WV CNMG 120408 ENWV 1/2 .031 ● ○.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNMG 432 ENBZ5 CNMG 120408 ENBZ5 1/2 .031 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNMG 432 Z5 CNMG 120408 TNBZ5 1/2 .031 ○ ໐

CNMG 431 ZF1 CNMG 120404 ENBZF1 1/2 .016 ● ● ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNMG 432 ZF1 CNMG 120408 ENBZF1 1/2 .031 ● ● ○

CNMG 433 ZF1 CNMG 120412 ENBZF1 1/2 .047 ● ○

CNGG 4304 FNZF1 CNGG 120401 FNZF1 1/2 .004 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNGG 4308 FNZF1 CNGG 120402 FNZF1 1/2 .008 ●CNGG 431 FNZF1 CNGG 120404 FNZF1 1/2 .016 ●CNGG 432 FNZF1 CNGG 120408 FNZF1 1/2 .031 ●

CNGG 431 FNZP CNGG 120404 FNZP 1/2 .016 ● ● ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNMP 432 ZP CNMG 120408 ENBZP 1/2 .031 ●

CNGG 432 FNZP CNGG 120408 FNZP 1/2 .031 ● ● ●

CNMG 432 ZW1 CNMG 120408 ENBZW1 1/2 .031 ● ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CNMG 433 ZW1 CNMG 120412 ENBZW1 1/2 .047 ● ●

CNGA 431 CNGA 120404 TN 1/2 .016 ●

―CNGA 432 CNGA 120408 TN 1/2 .031 ●CNGA 433 CNGA 120412 TN 1/2 .047 ●

■ 80 degree Diamond Negative type(CN..) (inch) IC TCN..43 1/2 3/16

Holders ➡ F6・F7・G4・J35

Insert Item List

[ Carbide

/ Cermet ]

E31

■ 80 degree Diamond Positive type(CP..) (inch) IC TCP..21.5 1/4 3/32CP..2.51.5 5/16 3/32CP..32.5 3/8 5/32

Holders ➡ J108

RT

R

IC

11°80°

100°Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

CPGR 422 AF1 CPGR 120308 AF1 1/2 .031 ●.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CPGT 21.504 FNAM3 CPGT 060201 FNXAM3 1/4 .004 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CPGT 21.508 FNAM3 CPGT 060202 FNXAM3 1/4 .008 ●CPGT 21.51 FNAM3 CPGT 060204 FNXAM3 1/4 .016 ●CPGT 32.504 FNAM3 CPGT 09T301 FNXAM3 3/8 .004 ●CPGT 32.508 FNAM3 CPGT 09T302 FNXAM3 3/8 .008 ●CPGT 32.51 FNAM3 CPGT 09T304 FNXAM3 3/8 .016 ●CPGT 32.52 FNAM3 CPGT 09T308 FNXAM3 3/8 .031 ●CPGH 32.504 AF1 CPGH 09T301 ENBAF1 3/8 .004 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

CPGH 32.508 AF1 CPGH 09T302 ENBAF1 3/8 .008 ●CPGH 32.51 AF1 CPGH 09T304 ENBAF1 3/8 .016 ●CPGH 32.52 AF1 CPGH 09T308 ENBAF1 3/8 .031 ●CPGH 21.504 AM5 CPGH 060201 ENBAM5 1/4 .004 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CPGH 21.508 AM5 CPGH 060202 ENBAM5 1/4 .008 ● ○CPGH 21.508 FNAM5 CPGH 060202 FNAM5 1/4 .008 ○ ○CPGH 21.51 AM5 CPGH 060204 ENBAM5 1/4 .016 ●CPGH 21.51 FNAM5 CPGH 060204 FNAM5 1/4 .016 ●CPGH 21.52 AM5 CPGH 060208 ENBAM5 1/4 .031 ●CPGP 2.51.508 ENBAM5 CPGP 080202 ENBAM5 5/16 .008 ○CPGP 2.51.508 FNAM5 CPGP 080202 FNAM5 5/16 .008 ○ ○CPGM 3208 ENBAM5 CPGM 090302 ENBAM5 3/8 .008 ○CPGM 3208 FNAM5 CPGM 090302 FNAM5 3/8 .008 ○ ○CPGM 321 ENBAM5 CPGM 090304 ENBAM5 3/8 .016 ○CPGM 321 FNAM5 CPGM 090304 FNAM5 3/8 .016 ○ ○CPGM 322 ENBAM5 CPGM 090308 ENBAM5 3/8 .031 ○CPGM 322 FNAM5 CPGM 090308 FNAM5 3/8 .031 ○ ○CPMH 21.51 AM5 CPMH 060204 AM5 1/4 .016 ●CPMH 2.51.51 AM5 CPMH 080204 AM5 5/16 .016 ●CPMH 2.51.52 AM5 CPMH 080208 AM5 5/16 .031 ●CPMH 321 AM5 CPMH 090304 AM5 3/8 .016 ●CPMH 322 AM5 CPMH 090308 AM5 3/8 .031 ●CPGP 6208 F A1 CPGH 040102 F A1 .187 .008 Ⓛ Ⓛ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

A1

A

CPGP 621 F A1 CPGH 040104 F A1 .187 .016 Ⓛ ⓁCPGP 21.508 F A CPGH 060202 F A 1/4 .008 Ⓛ ⓁCPGP 21.51 F A CPGH 060204 F A 1/4 .016 Ⓛ ⓁCPGH 2.51.508 F A CPGH 080202 F A 5/16 .008 Ⓛ ⓁCPGH 2.51.51 F A CPGH 080204 F A 5/16 .016 Ⓛ ⓁCPGP 6208 A1 CPGH 040102 T A1 .187 .008 Ⓛ ⓁCPGP 621 A1 CPGH 040104 T A1 .187 .016 Ⓛ ⓁCPGP 21.508 A CPGH 060202 T A 1/4 .008 Ⓛ ⓁCPGP 21.51 A CPGH 060204 T A 1/4 .016 Ⓛ ⓁCPGH 2.51.51 T A CPGH 080204 T A 5/16 .016 Ⓛ ⓁCPGP 6204 FRF1 CPGH 040101 F F1 .187 .004 R

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

CPGP 6208 FRF1 CPGH 040102 F F1 .187 .008 RCPGP 621 FRF1 CPGH 040104 F F1 .187 .016 RCPGP 21.508 FRF1 CPGH 060202 F F1 1/4 .008 RCPGP 21.51 FRF1 CPGH 060204 F F1 1/4 .016 R

Insert Item List

[ Carbide

/ Cermet ]

E32

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

■ 55 degree Diamond Positive type(DC..) (inch) IC TDC..21.5 1/4 3/32DC..32.5 3/8 5/32

Holders ➡ J28・J29・J30

RT

IC

7°55°

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

DCGT 21.51 FN1L DCGT 070204 FN1L 1/4 .008 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCGT 32.508 FN1L DCGT 11T302 FN1L 3/8 .008 ○

DCGT 32.51 FN1L DCGT 11T304 FN1L 3/8 .016 ○

DCGT 32.508 AF3 DCGT 11T302 ENBAF3 3/8 .008 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCGT 32.51 AF3 DCGT 11T304 ENBAF3 3/8 .016 ●

DCGT 21.501 FNAM3 DCGT 070200 FNAM3 1/4 .001 ● ● ○ ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCGT 21.504M FNAM3 DCGT 070201 MFNAM3 1/4 .003 ● ●DCGT 21.504 FNAM3 DCGT 070201 FNAM3 1/4 .004 ○ ●DCGT 21.504 FNAM3 DCGT 070201 FNXAM3 1/4 .004 ●DCGT 21.508M FNAM3 DCGT 070202 MFNAM3 1/4 .007 ● ●DCGT 21.508 AM3 DCGT 070202 ENBAM3 1/4 .008 ●DCGT 21.508 FNAM3 DCGT 070202 FNAM3 1/4 .008 ○ ●DCGT 21.508 FNAM3 DCGT 070202 FNXAM3 1/4 .008 ●DCGT 21.51M FNAM3 DCGT 070204 MFNAM3 1/4 .015 ● ●DCGT 21.51 AM3 DCGT 070204 ENBAM3 1/4 .016 ●DCGT 21.51 FNAM3 DCGT 070204 FNAM3 1/4 .016 ○ ●DCGT 21.51 FNAM3 DCGT 070204 FNXAM3 1/4 .016 ●DCGT 32.501 FNAM3 DCGT 11T300 FNAM3 3/8 .001 ● ● ● ○ ●DCGT 32.504M FNAM3 DCGT 11T301 MFNAM3 3/8 .003 ● ● ● ○ ○DCGT 32.504 FNAM3 DCGT 11T301 FNXAM3 3/8 .004 ●DCGT 32.508M FNAM3 DCGT 11T302 MFNAM3 3/8 .007 ● ● ● ○ ○DCGT 32.508 AM3 DCGT 11T302 ENBAM3 3/8 .008 ●DCGT 32.508 FNAM3 DCGT 11T302 FNAM3 3/8 .008 ● ○ ●DCGT 32.508 FNAM3 DCGT 11T302 FNXAM3 3/8 .008 ●DCGT 32.51M FNAM3 DCGT 11T304 MFNAM3 3/8 .015 ● ● ● ○ ○DCGT 32.51 FNAM3 DCGT 11T304 FNAM3 3/8 .016 ● ○ ●DCGT 32.51 FNAM3 DCGT 11T304 FNXAM3 3/8 .016 ●DCGT 32.52 FNAM3 DCGT 11T308 FNAM3 3/8 .031 ●DCGT 32.52 AM3 DCGT 11T308 ENBAM3 3/8 .031 ●DCGT 32.52 FNAM3 DCGT 11T308 FNXAM3 3/8 .031 ●DCMT 21.508 AM3 DCMT 070202 ENBAM3 1/4 .008 ○ ○DCMT 21.51 AM3 DCMT 070204 ENBAM3 1/4 .016 ● ○ ○DCMT 21.52 AM3 DCMT 070208 ENBAM3 1/4 .031 ○DCMT 32.508 AM3 DCMT 11T302 ENBAM3 3/8 .008 ○ ○DCMT 32.51 AM3 DCMT 11T304 ENBAM3 3/8 .016 ● ○ ○DCMT 32.52 AM3 DCMT 11T308 ENBAM3 3/8 .031 ● ○ ○DCMT 32.53 AM3 DCMT 11T312 ENBAM3 3/8 .047 ○ ○

Insert Item List

[ Carbide

/ Cermet ]

E33

Holders ➡ J28・J29・J30

RT

IC

7°55°

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

DCGT 21.504M AMX DCGT 070201M AMX 1/4 .003 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

DCGT 21.508M AMX DCGT 070202M AMX 1/4 .007 ●

DCGT 32.504M AMX DCGT 11T301M AMX 3/8 .003 ●

DCGT 32.508M AMX DCGT 11T302M AMX 3/8 .007 ●

DCGT 21.501 FNAZ7 DCGT 070200 FNAZ7 1/4 .001 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCGT 21.504M FNAZ7 DCGT 070201M FNAZ7 1/4 .003 ○DCGT 21.508M FNAZ7 DCGT 070202M FNAZ7 1/4 .007 ○DCGT 32.501 FNAZ7 DCGT 11T300 FNAZ7 3/8 .001 ○ ○ ● ○ ○DCGT 32.504M FNAZ7 DCGT 11T301M FNAZ7 3/8 .003 ○ ○ ● ○ ○DCGT 32.508M FNAZ7 DCGT 11T302M FNAZ7 3/8 .007 ○ ○ ● ○ ○DCGT 32.51M FNAZ7 DCGT 11T304M FNAZ7 3/8 .015 ○ ○ ● ○ ○DCGT 32.52 FNAZ7 DCGT 11T308 FNAZ7 3/8 .031 ○ ○ ○ ○

DCGT 21.504M CL DCGT 070201M CL 1/4 .003 ○ ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCGT 21.508M CL DCGT 070202M CL 1/4 .007 ○ ○DCGT 32.504M CL DCGT 11T301M CL 3/8 .003 ● ●DCGT 32.508M CL DCGT 11T302M CL 3/8 .007 ● ●DCGT 32.51M CL DCGT 11T304M CL 3/8 .015 ● ●

DCGT 32.508 FM DCGT 11T302 ENBFM 3/8 .008 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCGT 32.51 FM DCGT 11T304 ENBFM 3/8 .016 ●

DCGT 32.52 FM DCGT 11T308 ENBFM 3/8 .031 ●

DCET 21.502 KHG DCET 0702005 KHG 1/4 .002 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCET 21.503 KHG DCET 0702008 KHG 1/4 .003 ○DCET 21.507 KHG DCET 0702018 KHG 1/4 .007 ○DCET 21.508 KHG DCET 070202 KHG 1/4 .008 ○DCET 32.502 KHG DCET 11T3005 KHG 3/8 .002 Ⓡ ○DCET 32.503 KHG DCET 11T3008 KHG 3/8 .003 Ⓡ ○DCET 32.507 KHG DCET 11T3018 KHG 3/8 .007 Ⓡ ○DCET 32.508 KHG DCET 11T302 KHG 3/8 .008 Ⓡ ○

DCET 21.503 UHG DCET 0702008 UHG 1/4 .003 Ⓡ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCET 32.503 UHG DCET 11T3008 UHG 3/8 .003 Ⓡ

DCMT 21.508 QD DCMT 070202 ENAQD 1/4 .008 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCMT 21.51 QD DCMT 070204 ENAQD 1/4 .016 ○DCMT 32.508 QD DCMT 11T302 ENAQD 3/8 .008 ○DCMT 32.51 QD DCMT 11T304 ENAQD 3/8 .016 ○DCMT 32.52 QD DCMT 11T308 ENAQD 3/8 .031 ○

Insert Item List

[ Carbide

/ Cermet ]

E34

Carbide / Cermet

RT

IC

7°55°

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

DCGT 21.501 S DCGT 070200   S 1/4 .001 R ○ ⓁR

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCGT 21.504M S DCGT 070201M S 1/4 .003 R ⓇDCGT 21.504 S DCGT 070201   S 1/4 .004 R Ⓡ ⓁR ⓁRDCGT 21.508M S DCGT 070202M S 1/4 .007 R RDCGT 21.508 S DCGT 070202   S 1/4 .008 ○ ○ ⓁRDCGT 21.51 S DCGT 070204   S 1/4 .016 R ⓇDCGT 32.501 S DCGT 11T300  S 3/8 .001 R R R ○ RDCGT 32.504M S DCGT 11T301M S 3/8 .003 R R RDCGT 32.504 S DCGT 11T301   S 3/8 .004 Ⓡ ○ RDCGT 32.508M S DCGT 11T302M S 3/8 .007 R Ⓡ ⓇDCGT 32.508 S DCGT 11T302   S 3/8 .008 R ○ RDCGT 32.51M S DCGT 11T304M S 3/8 .015 R ⓇDCGT 32.51 S DCGT 11T304   S 3/8 .016 RDCMT 21.504 T AS DCMT 070201  T AS 1/4 .004 ○ ○DCMT 21.508 T AS DCMT 070202  T AS 1/4 .008 ○ ○DCMT 21.51 T AS DCMT 070204  T AS 1/4 .016 ○ ○DCMT 32.504 T AS DCMT 11T301  T AS 3/8 .004 ○ ○DCMT 32.508 T AS DCMT 11T302  T AS 3/8 .008 ○ ○DCMT 32.51 T AS DCMT 11T304  T AS 3/8 .016 ○ ○DCGT 21.501 U DCGT 070200   U 1/4 .001 Ⓡ Ⓡ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCGT 21.504 U DCGT 070201  U 1/4 .004 Ⓡ ⓇDCGT 21.508 U DCGT 070202  U 1/4 .008 Ⓡ ○DCGT 32.501 U1 DCGT 11T300  U1 3/8 .001 Ⓡ Ⓡ ○DCGT 32.504 U1 DCGT 11T301  U1 3/8 .004 Ⓡ Ⓡ Ⓡ ○DCGT 32.508 U1 DCGT 11T302  U1 3/8 .008 Ⓡ Ⓡ Ⓡ ○DCGT 32.51 U1 DCGT 11T304  U1 3/8 .016 Ⓡ Ⓡ ○DCMT 21.508 ENBZR DCMT 070202  ENBZR 1/4 .008 ○ ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DCMT 21.51 ENBZR DCMT 070204  ENBZR 1/4 .016 ○ ○DCMT 32.508 ENBZR DCMT 11T302  ENBZR 3/8 .008 ○ ○DCMT 32.51 ENBZR DCMT 11T304  ENBZR 3/8 .016 ○ ○DCMT 32.52 ENBZR DCMT 11T308  ENBZR 3/8 .031 ○ ○DCGW 21.500 V DCGW 07020  V 1/4 0 ○

DCGW 21.501 FN DCGW 070200  FN 1/4 .001 ○DCGW 21.501 H DCGW 070200  H 1/4 .001 ○DCGW 21.504 FN DCGW 070201  FN 1/4 .004 ○DCGW 21.504 H DCGW 070201  H 1/4 .004 ●DCGW 21.508 H DCGW 070202  H 1/4 .008 ○DCGW 32.500 V DCGW 11T30   V 3/8 0 ○DCGW 32.501 FN DCGW 11T300  FN 3/8 .001 ○DCGW 32.501 H DCGW 11T300  H 3/8 .001 ○DCGW 32.504 FN DCGW 11T301  FN 3/8 .004 ○DCGW 32.504 H DCGW 11T301  H 3/8 .004 ○DCGW 32.508 H DCGW 11T302  H 3/8 .008 ○

■ 55 degree Diamond Positive type(DC.. ,continued) (inch) IC TDC..21.5 1/4 3/32DC..32.5 3/8 5/32

Holders ➡ J28・J29・J30

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)  M:Mirror finish

M

M

MMM

M

MM

Insert Item List

[ Carbide

/ Cermet ]

E35

■ 55 degree Diamond Negative type(DN..) (inch) IC TDN..43 1/2 3/16DN..44 1/2 1/4DN..54 3/4 1/4

RT

IC 90°

55°

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

DNMG 431 G DNMG 150404 G 1/2 .016 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNMG 432 G DNMG 150408 G 1/2 .031 ○DNMG 433 G DNMG 150412 G 1/2 .047 ○DNMG 431 G DNMG 150404 ENBG 1/2 .016 ● ●DNMG 431 G DNMG 150404 TNG 1/2 .016 ○ ○DNMG 432 G DNMG 150408 ENBG 1/2 .031 ● ●DNMG 432 G DNMG 150408 TNG 1/2 .031 ○DNMG 433 G DNMG 150412 ENBG 1/2 .047 ●DNMG 441 G DNMG 150604 ENBG 1/2 .016 ○

DNGG 432 R6 DNGG 150408 ENBR6 1/2 .031 ●.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNGG 4304 RN1 DNGG 150401 T RN1 1/2 .004 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNGG 431 RN1 DNGG 150404 T RN1 1/2 .016 ●

DNGG 432 RN1 DNGG 150408 T RN1 1/2 .031 ●

DNMG 431 WM DNMG 150404 ENWM 1/2 .016 ● ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNMG 432 WM DNMG 150408 ENWM 1/2 .031 ● ○

DNMG 432 WR DNMG 150408 ENBWR 1/2 .031 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNMG 433 WR DNMG 150412 ENBWR 1/2 .047 ●

DNMG 432 WV DNMG 150408 ENWV 1/2 .031 ● ○.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNMG 432 Z5 DNMG 150408 TNBZ5 1/2 .031 ○ ○.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNMG 431 ZF1 DNMG 150404 ENBZF1 1/2 .016 ● ● ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNMG 432 ZF1 DNMG 150408 ENBZF1 1/2 .031 ● ● ○DNMG 441 ZF1 DNMG 150604 ENBZF1 1/2 .016 ○ ○DNMG 442 ZF1 DNMG 150608 ENBZF1 1/2 .031 ● ○

Holders ➡ F8・F9・G4

Insert Item List

[ Carbide

/ Cermet ]

E36

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

RT

IC 90°

55°

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

DNGG 4304 FNZF1 DNGG 150401 FNZF1 1/2 .004 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNGG 4308 FNZF1 DNGG 150402 FNZF1 1/2 .008 ●

DNGG 431 FNZF1 DNGG 150404 FNZF1 1/2 .016 ●

DNGG 432 FNZF1 DNGG 150408 FNZF1 1/2 .031 ●

DNGG 431 FNZP DNGG 150404 FNZP 1/2 .016 ● ● ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNGG 432 FNZP DNGG 150408 FNZP 1/2 .031 ● ● ●

DNMG 431 ZW1 DNMG 150404 ENBZW1 1/2 .016 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DNMG 432 ZW1 DNMG 150408 ENBZW1 1/2 .031 ●

DNMG 442 ZW1 DNMG 150608 ENBZW1 1/2 .031 ○ ○

DNGA 431 DNGA 150404 TN 1/2 .016 ●

―DNGA 432 DNGA 150408 TN 1/2 .031 ●

DNGA 433 DNGA 150412 TN 1/2 .047 ○

Holders ➡ F8・F9・G4

■ 55 degree Diamond Negative type(DN.. ,continued) (inch) IC TDN..43 1/2 3/16DN..44 1/2 1/4

Insert Item List

[ Carbide

/ Cermet ]

E37

RT

IC

11°55°

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

DPGT 21.504 FNAM3 DPGT 070201 FNAM3 1/4 .004 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

DPGT 21.508 AM3 DPGT 070202 ENBAM3 1/4 .008 ●DPGT 21.508 FNAM3 DPGT 070202 FNAM3 1/4 .008 ●DPGT 21.51 AM3 DPGT 070204 ENBAM3 1/4 .016 ●DPGT 21.51 FNAM3 DPGT 070204 FNXAM3 1/4 .016 ●DPGT 32.504 FNAM3 DPGT 11T301 FNAM3 3/8 .004 ●DPGT 32.508 AF3 DPGT 11T302 ENBAF3 3/8 .008 ●DPGT 32.508 FNAM3 DPGT 11T302 FNAM3 3/8 .008 ●DPGT 32.51 AF3 DPGT 11T304 ENBAF3 3/8 .016 ●DPGT 32.51 FNAM3 DPGT 11T304 FNAM3 3/8 .016 ●

DPGT 21.504 S DPGT 070201 S 1/4 .004 R.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

■ 75 degree Diamond Positive type(ER..) (inch) IC TER..52 5/32 .063

Holders ➡ J107

11°

RT

IC H

75°

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePCD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

ERGP 52Y F A2 ERGHT 30102 F A2 5/32 .008 ○ ○ ⓁR ○ ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

ERGP 521 F A2 ERGHT 30104 F A2 5/32 .016 R Ⓛ

ERGP 5204 F F1 ERGHT 30101 F F1 5/32 .004 R

.004

.016

.024

.031

.039

.002Feed (IPR)

Depth of cut (Inch)

.008.008

ERGP 52Y F F1 ERGHT 30102 F F1 5/32 .008 R

ERGP 521 F F1 ERGHT 30104 F F1 5/32 .016 R

■ 55 degree Diamond Positive type(DP..) (inch) IC TDP..21.5 1/4 3/32DP..32.5 3/8 5/32

Insert Item List

[ Carbide

/ Cermet ]

E38

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

■ Round type(RC.. / RN.. / RP..) (inch) IC TRP..08 .315 3/22RP..10 .394 7/64RP..12 .472 1/8RP..16 .630 3/16RP..20 .787 3/16

(inch) IC TRC..43 .472 3/16RN..32 3/8 1/8RN..43 1/2 3/16RP..06 .236 3/32

RC_ _, RP_ _ RN_ _

T

IC

T

IC

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

RCMX 43M0 GM RCMX 1204M0 ENBGM .472 ― ໐ ໐

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

RCMX 43M0 GB RCMX 1204M0 GB .472 ― ໐ ໐

RNMG 32 F RNMG 090300 ENBF 3/8 ― ໐.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

RNMG 43 G RNMG 120400 ENBG 1/2 ― ●.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

RPMT 0602M0 GB RPMT 0602M0 GB .236 ― ໐ ໐

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

RPMT 0802M0 GB RPMT 0802M0 GB .315 ― ໐ ໐RPMT 10T2M0 GB RPMT 10T2M0 GB .394 ― ໐ ໐RPMT 1203M0 GB RPMT 1203M0 GB .472 ― ໐ ໐RPMT 1604M0 GB RPMT 1604M0 GB .630 ― ໐ ●RPMT 2004M0 GB RPMT 2004M0 GB .787 ― ໐ ໐RPMX 1203M0 GB RPMX 1203M0 GB .472 ― ໐ ໐

Insert Item List

[ Carbide

/ Cermet ]

E39

■ 90 degree Square Positive type (SC.. / SD.. / SE..)

(inch) IC T HSD..53 5/8 3/16 ―SE..42 1/2 1/8 ―SE..53 5/8 3/16 ―

(inch) IC T HSC..32 3/8 1/8 .173SD..42 1/2 1/8 ―SD..43 1/2 3/16 ―

Cutters(SDCW) ➡ Ⅰ14・Ⅰ15・Ⅰ16

SCMT_ _ SD_ _ SECN_ _

R T

ICH 45°

15°

A

TIC 45°

20°

A

TICSteel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R[A]

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

SCMT 32.52 AM3

SCMT 32.52 AM5

SCMT 09T308 ENBAM3

SCMT 09T308 ENBAM5

3/8

3/8

.031

.031

○ .016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SDKN 42 AEN SDKN 1203 AEN 1/2 [.047] ○―

SDKN 53 A SDKN 1504 AETN 5/8 [.047] ○

SDC 42 A3 SDCN 1203 AE 1/2 [.047] ●

―SEK 42 AFN SEKN 1203 AFN 1/2 [.094] ●

SECN 42 AFTN SECN 1203 AFTN 1/2 [.094] ●

SECN 53 AFTN SECN 1504 AFTN 5/8 [.094] ●

SDCW 432 T0420 1/2 .031 ●

―SDCW 433 T0420 1/2 .047 ●

SDCW 434 T0420 1/2 .063 ●

※AE, EE, and PE come with wipers.

Insert Item List

[ Carbide

/ Cermet ]

E40

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

■ 90 degree Square Negative type(SN..) (inch) IC TSN..54 5/8 1/4SN..64 3/4 1/4

Holders ➡ F11・G5

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

SNMG 432 G SNMG 120408 G 1/2 .031 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNMG 433 G SNMG 120412 G 1/2 .047 ●

SNMG 434 G SNMG 120416 G 1/2 .063 ○

SNMG 322 K SNMG 090308 K 3/8 .031 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNMG 322 G SNMG 090308 ENBG 3/8 .031 ○SNMG 432 G SNMG 120408 ENBG 1/2 .031 ● ●SNMG 432 G SNMG 120408 TNG 1/2 .031 ○SNMG 433 G SNMG 120412 ENBG 1/2 .047 ● ●SNMG 433 G SNMG 120412 TNG 1/2 .047 ○SNMG 434 G SNMG 120416 ENBG 1/2 .063 ○

SNMG 432 WM SNMG 120408 ENWM 1/2 .031 ○ ○.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNMG 432 WR SNMG 120408 ENBWR 1/2 .031 ●.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNMG 432 Z5 SNMG 120408 ENBZ5 1/2 .031 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNMG 433 Z5 SNMG 120412 TNBZ5 1/2 .047 ○ ○

SNMG 432 ZF1 SNMG 120408 ENBZF1 1/2 .031 ● ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNMG 433 ZF1 SNMG 120412 ENBZF1 1/2 .047 ●

SNMG 432 ZW1 SNMG 120408 ENBZW1 1/2 .031 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNMG 433 ZW1 SNMG 120412 ENBZW1 1/2 .047 ●

SNGG 321 B SNGG 090304 T B 3/8 .016 Ⓛ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNGG 322 B SNGG 090308 T B 3/8 .031 ○

SNGG 431 B SNGG 120404 T B 1/2 .016 ○

R T

IC 90° 90°

(inch) IC TSN..32 3/8 1/8SN..43 1/2 3/16

Insert Item List

[ Carbide

/ Cermet ]

E41

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

SNGG 322 N1 SNGG 090308 N1 3/8 .031 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

SNGG 432 N1 SNGG 120408 N1 1/2 .031 R

SNGG 432 C SNGG 120408T C 1/2 .031 ໐ Ⓡ.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SNG 322 SNGN 090308 TN 3/8 .031 ໐

SNG 432 T0420 SNGN 120408 T01020 1/2 .031 ●

SNG 432 T0425 SNGN 120408 T01025 1/2 .031 ໐ ໐

SNG 433 T0420 SNGN 120412 T01020 1/2 .047 ●

SNG 434 T0420 SNGN 120416 T01020 1/2 .063 ●

Holders    ➡ F10・F11・G5Cutters(SNG) ➡ Ⅰ6・Ⅰ8・Ⅰ10 

R T

IC 90° 90°

Insert Item List

[ Carbide

/ Cermet ]

E42

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

SPGR 322 AF1 SPGR 090308 ENBAF1 3/8 .031 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SPGR 422 AF1 SPGR 120308 ENBAF1 1/2 .031 ●

SPGR 322 QZ SPGR 090308 ENBQZ 3/8 .031 ○.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

SPMH 326 T BH1 SPMH 090324 T BH1 3/8 .094 Ⓛ―

SPMH 328 T H1 SPMH 090332 T AH1 3/8 .126 Ⓛ

SPMR 4310 H2 SPMR 120440 T H2 1/2 .157 Ⓛ ―

SPG 321 SPGN 090304 TN 3/8 .016 ○

―SPG 322 SPGN 090308 TN 3/8 .031 ○SPG 422 SPGN 120308 TN 1/2 .031 ○ ○SPG 433 SPGN 120412 3/8 .047 ●SPC 422 SPCN 120308 1/2 .031 ●

―SPC 433 SPCN 120412 1/2 .047 ●SPC 633 SPCN 190412 1/2 .047 ●SPC 634 SPCN 190416 1/2 .063 ●

SPCE 732 SPCE 050208 7/32 .031 ●―

SPCE 032 SPCE 070208 5/16 .031 ●

SPEB 222 SPEB 060308 1/4 .031 ● ―

SPKN 42 EDT SPKN 1203 EDT 1/2 ●―

SPKN 53 EDT SPKN 1504 EDT 5/8 R

SPME 032 SPME 070208 1/4 .031 ● ―

SPM 322 SPMN 090308 3/8 .031 ●

―SPM 422 SPMN 120308 1/2 .031 ●SPM 4310 SPMN 120440 TN 1/2 .157 ○SPM 632 SPMN 190408 TN 3/4 .031 ○

TIC

R 11

(inch) IC TSP..43 1/2 3/16SP..53 5/8 3/16SP..63 3/4 3/16SP..73 7/32 3/32

(inch) IC TSP..22 1/4 1/8SP..32 3/8 1/8SP..42 1/2 1/8

■ 90 degree Square Positive type(SP..)

Insert Item List

[ Carbide

/ Cermet ]

E43

■ 60 degree Triangle Positive type (TB.. / TC.. / TE..)

(inch) IC TTC..52 5/32 1/16TC..73 7/32 3/32TE..43 1/2 3/16

(inch) IC TTB..52 5/32 1/16TC..21 1/4 3/32TC..32 3/32 5/32

60°

ICR

11°

TC_ _, TE_ _TB_ _

60°

IC

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

TBGE 521 TBGE 060104 5/32 .016 ●―

TBGE 522 TBGE 060108 5/32 .031 ○

TCGT 21.508 FNAM3 TCGT 110202 FNXAM3 1/4 .008 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TCGT 32.508 AM3 TCGT 16T302 ENBAM3 3/32 .008 ●

TCGT 32.51 AM3 TCGT 16T304 ENBAM3 3/32 .016 ●

TCMT 21.51 AM3 TCMT 110204 ENBAM3 1/4 .016 ○

TCGT 21.504 AF1 TCGT 110201 AF1 1/4 .004 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

TCGT 21.51 AF1 TCGT 110204 AF1 1/4 .016 ●

TCGT 21.52 AF1 TCGT 110208 AF1 1/4 .031 ●

TCMT 21.508 QD TCMT 110202 ENAQD 1/4 .008 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TCMT 21.51 QD TCMT 110204 ENAQD 1/4 .016 ○TCMT 21.52 QD TCMT 110208 ENAQD 1/4 .031 ○TCMT 32.51 QD TCMT 16T304 ENAQD 3/32 .016 ○TCMT 32.52 QD TCMT 16T308 ENAQD 3/32 .031 ○

TCMT 32.52 AM5 TCMT 16T308 ENBAM5 3/32 .031 ○.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TCGT 7304 S TCGT 090201 S 7/32 .004 Ⓡ ໐ R

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TCGT 7308 S TCGT 090202 S 7/32 .008 ○ R

TCGT 21.504 S TCGT 110201 S 1/4 .004 ໐ R

TCGT 7304 RU TCGT 090201 U 7/32 .004 Ⓡ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TCGT 7308 RU TCGT 090202 U 7/32 .008 Ⓡ

TCGH 5204 T B1 TCGH 060101 T B1 5/32 .004 L

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TCGH 5208 F B1 TCGH 060102 F B1 5/32 .008 Ⓛ ⓁTCGH 5208 T B1 TCGH 060102 T B1 5/32 .008 ○TCGH 521 F B1 TCGH 060104 F B1 5/32 .016 Ⓛ ⓁTCGH 521 T B1 TCGH 060104 T B1 5/32 .016 LTCGP 5204 F F05 TCGH 060101 F F05 5/32 .004 R

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TCGP 5208 F F05 TCGH 060102 F F05 5/32 .008 ⓁR Ⓡ ○TCGP 5208 F05 TCGH 060102 T F05 5/32 .008 ○ ⓇTCGP 521 F F05 TCGH 060104 F F05 5/32 .016 R Ⓡ ⓇTCGP 521 F05 TCGH 060104 T F05 5/32 .016 ○ ⓇTCGD 52Y TCGB 060102 TN 5/32 .008 ○

TCGD 521 TCGB 060104 TN 5/32 .016 ●TCGW 7301 FN TCGW 090200 FN 7/32 .001 ໐TCGW 7304 FN TCGW 090201 FN 7/32 .004 ໐TCGW 21.501 FN TCGW 110200 FN 1/4 .001 ○TCGW 21.504 FN TCGW 110201 FN 1/4 .004 ○

TEEN 43 PR TEEN 2204 PFTR 1/2 .016 ○ ―

Holders(TC) ➡ J109

Insert Item List

[ Carbide

/ Cermet ]

E44

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

■ 60 degree Triangle Negative type(TN..) (inch) IC TTN..33 3/8 3/16TN..43 1/2 3/16

(inch) IC TTN..22 1/4 1/8TN..32 3/8 1/8

Holders ➡ F14・J34

60°

90°

IC

T Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

TNEG 3304M F D1 TNEG 160401M F D1 3/8 .003 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNEG 3308 F D1 TNEG 160402 F D1 3/8 .008 ○ ○TNEG 331 F D1 TNEG 160404 F D1 3/8 .016 ○ ○TNEG 332 F D1 TNEG 160408 F D1 3/8 .031 ○ ○TNGA 222 TNGA 110308 TN 1/4 .031 ○

TNGA 322 TNGA 160308 TN 3/8 .031 ●TNGA 332 TNGA 160408 TN 3/8 .031 ○TNGA 333 TNGA 160412 TN 3/8 .047 ○TNGA 432 TNGA 220408 TN 1/2 .031 ○TNGA 433 TNGA 220412 TN 1/2 .047 ●TNGG 221 B TNGG 110304 T B 1/4 .016 LⓇ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNGG 222 B TNGG 110308 T B 1/4 .031 ⓁTNGG 322 B TNGG 160308 T B 3/8 .031 ⓁTNGG 331 B TNGG 160404 T B 3/8 .016 ○TNGG 332 B TNGG 160408 T B 3/8 .031 ○TNGG 3308 F C TNGG 160402 F C 3/8 .008 Ⓡ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)TNGG 332 T C TNGG 160408 T C 3/8 .031 ○

TNGG 431 C TNGG 220404 T C 1/2 .016 ●TNGG 432 C TNGG 220408 T C 1/2 .031 ●TNMG 331 C TNMG 160404 T C 3/8 .016 ○ ⓇTNMG 332 C TNMG 160408 T C 3/8 .031 ○

TNGG 3304 F DA TNGG 160401 F DA 3/8 .004 Ⓡ Ⓡ Ⓡ.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNGG 331 L2 TNGG 160404 L2 3/8 .016 R

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

TNGG 332 L2 TNGG 160408 L2 3/8 .031 R

TNGG 321 N1 TNGG 160304 N1 3/8 .016 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNGG 322 N1 TNGG 160308 N1 3/8 .031 LTNGG 3308 N1 TNGG 160402 T N1 3/8 .008 ○TNGG 331 N1 TNGG 160404 T N1 3/8 .016 ●TNGG 332 N1 TNGG 160408 T N1 3/8 .031 ●

TNGG 332 R1 TNGG 160408 ENBR1 3/8 .031 ●.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNGG 3304 F U2 TNGG 160401 F U2 3/8 .004 Ⓡ Ⓡ R

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNGG 3308 F U2 TNGG 160402 F U2 3/8 .008 ○ ○ ⓁRTNGG 331 F U2 TNGG 160404 F U2 3/8 .016 ○ ○ ⓁRTNGG 332 F U2 TNGG 160408 F U2 3/8 .031 ○ ⓁR

TNGG 3304M FNUL TNGG 160401M FNUL 3/8 .003 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

TNGG 3308M FNUL TNGG 160402M FNUL 3/8 .007 ●

TNGG 331M FNUL TNGG 160404M FNUL 3/8 .015 ●

Insert Item List

[ Carbide

/ Cermet ]

E45

60°

90°IC

T Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

TNGG 322 FNZF1 TNGG 160308 FNZF1 3/16 .031 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

TNGG 331 FNZF1 TNGG 160404 FNZF1 3/16 .016 ●

TNGG 332 FNZF1 TNGG 160408 FNZF1 3/16 .031 ●

TNGG 3308 FNZP TNGG 160402 FNZP 3/8 .008 ○ ○ ○ ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNGG 331 FNZP TNGG 160404 FNZP 3/8 .016 ○ ● ○ ●

TNGG 332 FNZP TNGG 160408 FNZP 3/8 .031 ○ ● ○ ●

TNMA 332 TNMA 160408 TN 3/16 .031 ● ―

TNMG 332 G TNMG 160408 G 3/8 .031 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNMG 333 G TNMG 160412 G 3/8 .047 ●

TNMG 221 F TNMG 110304 ENBF 3/8 .016 ●TNMG 321 F TNMG 160404 ENBF 3/16 .016 ●TNMG 322 F TNMG 160408 ENBF 3/16 .031 ●TNMG 321 G TNMG 160304 ENBG 3/16 .016 ●TNMG 322 G TNMG 160308 ENBG 3/16 .031 ●TNMG 323 G TNMG 160316 ENBG 3/16 1/16 ●TNMG 331 G TNMG 160404 ENBG 3/8 .016 ● ●TNMG 331 G TNMG 160404 TNG 3/8 .016 ○TNMG 332 G TNMG 160408 ENBG 3/8 .031 ● ●TNMG 332 G TNMG 160408 TNG 3/8 .031 ○TNMG 333 G TNMG 160412 ENBG 3/8 .047 ● ○TNMG 333 G TNMG 160412 TNG 3/8 .047 ○TNMG 431 G TNMG 220404 ENBG 1/2 .016 ●TNMG 432 G TNMG 220408 ENBG 1/2 .031 ● ●TNMG 433 G TNMG 220412 ENBG 1/2 .047 ● ●

TNMG 331 WM TNMG 160404 ENWM 3/8 .016 ● ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNMG 332 WM TNMG 160408 ENWM 3/8 .031 ● ○

TNMG 332 WR TNMG 160408 ENBWR 3/8 .031 ●.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNMG 332 WV TNMG 160408 ENWV 3/8 .031 ● ○.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNMG 331 Z5 TNMG 160404 TNBZ5 3/8 .016 ○ ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNMG 332 Z5 TNMG 160408 ENBZ5 3/8 .031 ○

TNMG 332 Z5 TNMG 160408 TNBZ5 3/8 .031 ○ ○

Holders ➡ F14・J34

Insert Item List

[ Carbide

/ Cermet ]

E46

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

60°

90°

IC

T Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

TNMG 322 ZF1 TNMG 160308 ENBZF1 3/16 .031 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)TNMG 323 ZF1 TNMG 160312 ENBZF1 3/16 .047 ●

TNMG 331 ZF1 TNMG 160404 ENBZF1 3/8 .016 ● ● ໐TNMG 332 ZF1 TNMG 160408 ENBZF1 3/8 .031 ● ● ○TNMG 333 ZF1 TNMG 160412 ENBZF1 3/8 .047 ●TNMG 432 ZF1 TNMG 220408 ENBZF1 1/2 .031 ●TNMP 331 ZP TNMG 160404 ENBZP 3/8 .016 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNMP 332 ZP TNMG 160408 ENBZP 3/8 .031 ●

TNMP 432 ZP TNMG 220408 ENBZP 1/2 .031 ●TNMG 321 ZW1 TNMG 160304 ENBZW1 3/16 .016 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TNMG 322 ZW1 TNMG 160308 ENBZW1 3/16 .031 ● ●TNMG 331 ZW1 TNMG 160404 ENBZW1 3/8 .016 ●TNMG 332 ZW1 TNMG 160408 ENBZW1 3/8 .031 ● ●TNMG 432 ZW1 TNMG 220408 ENBZW1 1/2 .031 ●

Holders ➡ F14・J34

(inch) IC TTN..32 3/8 1/8TN..33 3/8 3/16TN..43 1/2 3/16

■ 60 degree Triangle Negative type(TN.. ,continued)

Insert Item List

[ Carbide

/ Cermet ]

E47

Holders ➡ J109

■ 60 degree Triangle Positive type (TP..) (inch) IC TTP..63 3/16 3/32TP..73 7/32 3/32

(inch) IC TTP..22 1/4 1/8TP..32 3/8 1/8TP..43 1/2 3/16

60°

11°IC

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

TP 404 TPGA 110201 1/4 .004 ●

―TP 41 TPGA 110204 1/4 .016 ●TP 42 TPGA 110208 1/4 .031 ●TP 62 TPGA 160308 3/8 .031 ●TPC 2204 TPCN 110301 1/4 .004 ●

TPC 3204 TPCN 160301 3/8 .004 ●TPC 322 TPCN 160308 3/8 .016 ●TPC 432 TPCN 220408 1/2 .016 ●

TPC 433 TPCN 220412 1/2 .047 ●TPG 221 TPGN 110304 TN 1/4 .016 ●

TPG 222 TPGN 110308 TN 1/4 .031 ● ○TPG 321 FN TPGN 160304 FN 3/8 .016 ●TPG 321 TPGN 160304 TN 3/8 .016 ●TPG 322 FN TPGN 160308 FN 3/8 .031 ●TPG 322 TPGN 160308 TN 3/8 .031 ○ ●TPG 431 TPGN 220404 TN 1/2 .016 ●TPG 432 TPGN 220408 TN 1/2 .031 ●TPG 433 TPGN 220412 TN 1/2 .047 ●TPG 435 TPGN 220420 TN 1/2 .079 ○

TPGE 731 TPGE 090204 7/32 .016 ●

TPGE 732 TPGE 090208 7/32 .031 ●

TPGD 63Y TPGB 080202 TN 3/16 .008 ○

―TPGD 631 TPGB 080204 TN 3/16 .016 ○TPGD 73Y TPGB 090202 TN 7/32 .008 ○TPGD 731 TPGB 090204 TN 7/32 .016 ○TPGH 6308 F B3 TPGH 080202 F B3 3/16 .008 Ⓛ Ⓛ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TPGH 631 F B3 TPGH 080204 F B3 3/16 .016 Ⓛ ⓁTPGH 631 B3 TPGH 080204 T B3 3/16 .016 LTPGH 7308 F B2 TPGH 090202 F B2 7/32 .008 Ⓛ ⓁTPGH 731 F B2 TPGH 090204 F B2 7/32 .016 Ⓛ ⓁTPGH 731 B2 TPGH 090204 T B2 7/32 .016 ●TPGH 732 B2 TPGH 090208 F B2 7/32 .031 Ⓛ ⓁTPGH 2204 B3 TPGH 110301 T B3 1/4 .004 LTPGH 221 B3 TPGH 110304 T B3 1/4 .016 LTPGH 222 B3 TPGH 110308 T B3 1/4 .031 LTPGH 6308 F F1 TPGH 080202 F F1 3/16 .008 Ⓡ Ⓡ Ⓡ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

chip backward

TPGH 631 F F1 TPGH 080204 F F1 3/16 .016 Ⓡ Ⓡ ⓇTPGH 7304 F F1 TPGH 090201 F F1 7/32 .004 ⓇTPGH 7308 F F1 TPGH 090202 F F1 7/32 .008 Ⓡ Ⓡ ⓇTPGH 731 F F1 TPGH 090204 F F1 7/32 .016 Ⓡ Ⓡ ⓇTPGH 732 F F1 TPGH 090208 F F1 7/32 .031 Ⓡ ⓇTPGH 2208 F F1 TPGH 110302 F F1 1/4 .008 Ⓡ Ⓡ ⓇTPGH 221 F F1 TPGH 110304 F F1 1/4 .016 Ⓡ Ⓡ ⓇTPGH 222 F F1 TPGH 110308 F F1 1/4 .031 Ⓡ Ⓡ

Insert Item List

[ Carbide

/ Cermet ]

E48

Carbide / Cermet

Holders ➡ J109

60°

11°IC

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

TPGH 6308 F1 TPGH 080202 T F1 3/16 .008 Ⓡ Ⓡ

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

chip backward

TPGH 631 F1 TPGH 080204 T F1 3/16 .016 Ⓡ Ⓡ

TPGP 7308 F1 TPGH 090202 T F1 7/32 .008 Ⓡ Ⓡ

TPGP 731 F1 TPGHP 090204 T F1 7/32 .016 Ⓡ Ⓡ

TPGP 2208 F1 TPGH 110302 T F1 1/4 .008 Ⓡ Ⓡ

TPGP 221 F1 TPGH 110304 T F1 1/4 .016 Ⓡ Ⓡ

TPGP 222 F1 TPGH 110308 T F1 1/4 .031 Ⓡ Ⓡ

TPGP 7308 FG TPGH 090202 FG 7/32 .008 Ⓡ R

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TPGP 731 FG TPGH 090204 FG 7/32 .016 Ⓡ R

TPGH 2208 FG TPGH 110302 FG 1/4 .008 Ⓡ R

TPGH 221 FG TPGH 110304 FG 1/4 .016 Ⓡ R

TPGR 221 AF1 TPGR 110304 ENBAF1 1/4 .016 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

TPGR 221 FNAF1 TPGR 110304 FNAF1 1/4 .016 ●

TPGR 222 AF1 TPGR 110308 ENBAF1 1/4 .031 ●

TPGR 321 AF1 TPGR 160304 ENBAF1 3/8 .016 ●

TPGR 321 FNAF1 TPGR 160304 FNAF1 3/8 .016 ●

TPGR 322 AF1 TPGR 160308 ENBAF1 3/8 .031 ●

TPGR 322 FNAF1 TPGR 160308 FNAF1 3/8 .031 ●

TPGR 431 AF1 TPGR 220404 ENBAF1 1/2 .016 ●

TPGR 432 AF1 TPGR 220408 ENBAF1 1/2 .031 ●TPGS 731 P1 TPGS 090204 P1 7/32 .016 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

TPGR 221 P1 TPGR 110304 1/4 .016 ●TPGR 321 P1 TPGR 160304 3/8 .016 ●TPGR 322 P1 TPGR 160308 3/8 .031 ●

TPKN 32 PDTR TPKN 1603 PDTR 3/8 .012 ●―

TPKN 43 PDTR TPKN 2204 PDTR 1/2 .016 ●

TPM 221 TPMN 110304 1/4 .016 ●

―TPM 222 TPMN 110308 1/4 .031 ●TPM 321 TPMN 160304 3/8 .016 ●TPM 322 TPMN 160308 3/8 .031 ●

TPMR 221 A283 TPMR 110304 A283 1/4 .016 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

TPMR 321 A283 TPMR 160304 A283 3/8 .016 ●

TPMR 322 A305 TPMR 160308 A305 3/8 .031 ●

■ 60 degree Triangle Positive type  (TP.. ,continued)

(inch) IC TTP..63 3/16 3/32TP..73 7/32 3/32

(inch) IC TTP..22 1/4 1/8TP..32 3/8 1/8TP..43 1/2 3/16

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)  M:Mirror finish

Insert Item List

[ Carbide

/ Cermet ]

E49Holders(VC) ➡ J31

■ 35 degree Diamond Positive type (VB.. / VC..)

(inch) IC TVC..13 .313 .125VC..22 1/4 1/8

VB_ _

5°35°

IC

VC_ _

7°35°

IC

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

VBG 21.508 FNAM3 VBGT 110202 FNXAM3 1/4 .008 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VBG 21.51 FNAM3 VBGT 110204 FNXAM3 1/4 .016 ●VBG 2208 FNAM3 VBGT 110302 FNXAM3 1/4 .008 ●VBG 221 FNAM3 VBGT 110304 FNXAM3 1/4 .016 ●VBGT 3304 AM3 VBGT 160401 AM3 3/8 .004 ●VBGT 3308 AM3 VBGT 160402 AM3 3/8 .008 ●VBMT 331 AM3 VBMT 160404 ENBAM3 3/8 .016 ○VBGT 331 GA VBGT 160404 ENBGA 3/8 .016 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VBGT 332 GA VBGT 160408 ENBGA 1/32 .031 ●

VBGT 333 GA VBGT 160412 ENBGA 3/8 .047 ●

VCET 2203 RUHG VCET 1103008 UHG 1/4 .003 Ⓡ.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VCGT 21.508 FN1L VCGT 110202 FN1L 1/4 .008 ○.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VCGT 2201 FNAZ7 VCGT 110300 FNAZ7 1/4 .001 ● ◯ ◯

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VCGT 2204M FNAZ7 VCGT 110301M FNAZ7 1/4 .003 ● ◯ ◯VCGT 2208M FNAZ7 VCGT 110302M FNAZ7 1/4 .007 ● ◯ ◯VCGT 221M FNAZ7 VCGT 110304M FNAZ7 1/4 .015 ● ◯ ◯VCGT 2201 FNAM3 VCGT 110300 FNAM3 1/4 .001 ● ● ● ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VCGT 2204M FNAM3 VCGT 110301M FNAM3 1/4 .003 ● ◯ ● ◯VCGT 2204 FNAM3 VCGT 110301 FNAM3 1/4 .004 ● ●VCGT 2208M FNAM3 VCGT 110302M FNAM3 1/4 .007 ● ◯ ● ○VCGT 2208 FNAM3 VCGT 110302 FNAM3 1/4 .008 ● ●VCGT 2208 FNAM3 VCGT 110302 FNXAM3 1/4 .008 ○VCGT 221M FNAM3 VCGT 110304M FNAM3 1/4 .015 ● ◯ ●VCGT 221 FNAM3 VCGT 110304 FNAM3 1/4 .016 ◯

VCGT 130300F 2M VCGT 130300 F 2M .313 .001 ◯

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VCGT 130301F 2M VCGT 130301 F 2M .313 .004 ◯

VCGT 2201 U VCGT 110300 U 1/4 .001 R R

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VCGT 2204M U VCGT 110301M U 1/4 .003 ⓇVCGT 2204 U VCGT 110301 U 1/4 .004 R RVCGT 2208M U VCGT 110302M U 1/4 .007 ⓇVCGT 2208 U VCGT 110302 U 1/4 .008 R RVCMT 2204 T AS VCMT 110301 T AS 1/4 .004 ◯ ◯

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VCMT 2208 T AS VCMT 110302 T AS 1/4 .008 ◯ ◯

VCMT 221 T AS VCMT 110304 T AS 1/4 .016 ◯ ◯

VCGW 2201 H VCGW 110300 H 1/4 .001 ●―VCGW 2204 H VCGW 110301 H 1/4 .004 ●

VCGW 2208 H VCGW 110302 H 1/4 .008 ◯

VCGT 2204M CL VCGT 110301M CL 1/4 .003 ● ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VCGT 2208M CL VCGT 110302M CL 1/4 .007 ● ●

(inch) IC TVB..21 1/4 3/32VB..22 1/4 1/8VB..33 3/8 3/16

MMM

Insert Item List

[ Carbide

/ Cermet ]

E50

Carbide / Cermet

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery  R:Stock(Right-hand only)  L:Stock(Left-hand only)

■ 35 degree Diamond type(VN.. / VP..) (inch) IC TVP..08 3/16 3/32VP..22 1/4 1/8

Holders(VN) ➡ F12・F13Holders(VP) ➡ J32   

VN_ _

90°

35°

IC

VP_ _

11°35°

IC

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

VNGA 332 VNGA 160408 3/8 .031 ● ―

VNGG 3304 N1 VNGG 160401 N1 3/8 .004 ●

.016.008.004.004.012.020.040.118.200

.002Feed (IPR)

Depth of cut (inch)

VNGG 331 N1 VNGG 160404 N1 3/8 .016 ●

VNGG 332 N1 VNGG 160408 N1 3/8 .031 ●VNGG 3308 FNZP VNGG 160402 FNZP 3/8 .008 ◯ ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VNMP 331 ZP VNMM 160404 ENBZP 3/8 .016 ●VNGG 331 FNZP VNGG 160404 FNZP 3/8 .016 ◯ ●VNGG 332 FNZP VNGG 160408 FNZP 3/8 .031 ◯ ●VNMG 331 GE VNMG 160404 GE 3/8 .016 ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VNMG 331 AM1 VNMG 160404 ENAM1 3/8 .016 ● ◯VNMG 331 AM1 VNMG 160404 ENBAM1 3/8 .016 ● ◯ ◯VNMG 331 AM1 VNMG 160404 TNBAM1 3/8 .016 ◯ ◯VNMG 332 AM1 VNMG 160408 ENAM1 3/8 .031 ● ◯VNMG 332 AM1 VNMG 160408 ENBAM1 3/8 .031 ● ◯ ◯VNMG 332 AM1 VNMG 160408 TNBAM1 3/8 .031 ◯ ◯VNMG 333 AM1 VNMG 160412 ENBAM1 3/8 .047 ●VNMG 431 AM1 VNMG 220404 AM1 1/2 .016 ●VNMG 432 AM1 VNMG 220408 AM1 1/2 .031 ●

VNMG 331 G VNMG 160404 G 3/8 .016 ◯

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VNMG 332 G VNMG 160408 G 3/8 .031 ◯

VNMG 333 G VNMG 160412 G 3/8 .047 ◯

VNMG 332 WM VNMG 160408 ENWM 3/8 .031 ● ◯.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VNMG 331 ZF1 VNMG 160404 ENBZF1 3/8 .016 ●.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VPET 0802005 KHG VPET 0802005 KHG .187 .002 ◯

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VPET 0802008 KHG VPET 0802008 KHG .187 .003 Ⓡ ◯VPET 0802018 KHG VPET 0802018 KHG .187 .007 ◯VPET 080202 KHG VPET 080202 KHG .187 .008 ◯VPET 2202 KHG VPET 1103005 KHG 1/4 .002 R ◯VPET 2203 KHG VPET 1103008 KHG 1/4 .003 Ⓡ ◯VPET 2207 KHG VPET 1103018 KHG 1/4 .007 Ⓡ ◯VPET 2208 KHG VPET 110302 KHG 1/4 .008 Ⓡ ◯

VPET 0802008 UHG VPET 0802008 UHG .187 .003 ◯.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VPGT 2201 FNAM3 VPGT 110300 FNAM3 1/4 .001 ◯ ◯

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

VPGT 2204M FNAM3 VPGT 110301M FNAM3 1/4 .003 ◯ ◯ ●

VPGT 2208M FNAM3 VPGT 110302M FNAM3 1/4 .007 ◯ ●

(inch) IC TVN..33 3/8 3/16VN..43 1/2 .187

Insert Item List

[ Carbide

/ Cermet ]

E51

■ 80 degree Hexagon type(WC.. / WP.. / WN..) (inch) IC TWC..21 1/4 3/32WC..52 5/32 1/16WN..43 1/2 3/16

WC_ _

80°

IC

WP_ _ WN_ _

80°

IC

11°

80°

IC

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Shape Item Number ISO Item Number IC R

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

WCGT 521 QB WCGT 020104 QB 5/8 .016 ○

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

WCGT 21.504 FNAM3 WCGT 040201 FNXAM3 1/4 .004 ●WCGT 21.508 FNAM3 WCGT 040202 FNXAM3 1/4 .008 ●WCGT 21.51 FNAM3 WCGT 040204 FNXAM3 1/4 .016 ●WPGT 21.504 FNAM3 WPGT 040201 FNXAM3 1/4 .004 ●WPGT 21.508 FNAM3 WPGT 040202 FNXAM3 1/4 .008 ●WPGT 21.51 FNAM3 WPGT 040204 FNXAM3 1/4 .016 ●

WNMG 432 G WNMG 080408 G 1/2 .031 ◯

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

WNMG 433 G WNMG 080412 G 1/2 .047 ◯

WNMG 432 WR WNMG 080408 ENWR 1/2 .031 ● ● ໐.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

WNMG 432 WV WNMG 080408 ENWV 1/2 .031 ● ໐.016.008.004

.004

.012

.020

.040

.118

.200

.002Feed (IPR)

Depth of cut (Inch)

WNMG 432 Z5 WNMG 080408 TNBZ5 1/2 .031 ໐ ໐

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

WNMG 433 Z5 WNMG 080412 TNBZ5 1/2 .047 ໐ ໐

WNGG 431 FNZP WNGG 080404 FNZP 1/2 .016 ໐ ● ●

.016.008.004.004.012.020.040.118

.200

.002Feed (IPR)

Depth of cut (Inch)

WNGG 432 FNZP WNGG 080408 FNZP 1/2 .031 ໐ ● ●

Holders(WN) ➡ F15・G5

Insert Item List

[ Carbide

/ Cermet ]

MEMO

F1

General Turning Toolholders

●Holder Identification System …… F2●Selection Guide …………………… F4●For CN.. Inserts …………………… F6●For DN.. Inserts …………………… F8●For SN.. Inserts ……………………F10●For VN.. Inserts ……………………F12●For TN.. Inserts ……………………F14●For WN.. Inserts ……………………F15●For RN.. Inserts ……………………F16●For RC / RP.. Inserts ………………F17●For CDH.. Inserts …………………F20

F

General Turning

Toolholders

F2

General Turning Toolholders■ Holder Identification System

C C L R 16 5-- DN

A B D F G

91° 75° 45° 91° 91°

H J K L N

107° 30' 93° 75° 95°

62° 30'

P R S V X

117° 30' 75° 45°

72° 30'

SpecialDesign

❸ Approach Angle

❼ Insert SizeIC(inch) 1/4 3/8 1/2 5/8 3/4 1

T 2 3 4 5 6 8

S

R 2 3 4 5 6 8

W 2 3 4 5 6

80° C 3 4 5 6 8

55° D 3 4 5 6 8

35° V 2 3

❻ Shank Size [Height( )and Width( )](inch)06 08 10 12 16 20 24 85.375 .500 .625 .750 1.000 1.250 1.500 1.250.375 .500 .625 .750 1.000 1.250 1.500 1.000

❽ Length of toolholder ( )(inch)B C D E

4.500 5.000 6.000 7.000

❺ Hand of Tool

R

L

N

C D R S

80°

80°Diamond

55°

55°Diamond Round Square

T V W

Triangluar

35°

35°Diamond

80°

Trigon

❷ Insert Shape

❹ Insert Relief Angle

N:0°B:5°C:7°P:11°D:15°E:20°

B C Clamp-onV 

W Multi-clampP Lever-lockH Bolt-clampS Screw-on

❶ Clamping System

❶ ❷ ❸ ❹ ❺ ❻ ❼ ❽

In case of = , the number will represent the number of sixteeths of and .In case of ≠ , the first digit represents the numuber of eighths of , and the second digit represents the number of quarters of .

General Turning

Toolholders

F3

Multi Clamp Toolholders

BRV Toolholder System

● Three clamping configurations available with one toolholder just by changing a clamp

● Clamp screw also accessible from bottom of the toolholder Dramatically improved accessibility when using toolholder up-side down

● BRV toolholder is a modular tooling system designed for ceramic V-bottom inserts for profiling This system provides excellent index repeatability and rigid clamping● The BRV toolholder can be used in four configurations to cut the cost for preparing separate toolholders

Features

Features

■ Double-clamp type ■ Dimple-clamp type ■ Clamp-on type

General Turning

Toolholders

F4

Selection Guide

Lead Angle 95° 75°(Using 100°Corner) 91° 91° 95°

Tooling

95° 75° 91° 91° 95°

Insert shape

CNG / CNGX / CNGA CNG / CNGA TNG / TNGA WNGA

Perfect for Ceramic Insert

Multi Clamp WCLN ➡F6 WCBN ➡F7 WTGN ➡F14 WTFN ➡F14 WWLN ➡F15WWLN-2

Clamp On CCLN ➡F6

For Insert in General Lever Lock PCLN ➡J35

Lead Angle 75° 75° 45° 45°

Tooling

75° 75° 45° 45°

Insert shape

SNG / SNGX SNG / SNGX / SNGA

Perfect for Ceramic Insert

Multi Clamp WSSN ➡F11 WSDN ➡F11

Clamp On CSKN ➡F10 CSRN ➡F10 CSSN ➡F10 CSDN ➡F11

Lead Angle 93° 107°30' 62°30' 93° 117°30' 72°30'

Tooling

93°107° 30'

62° 30' 93°

117° 30'

72° 30'

Insert shape

DNGA / DNGX VNGA / VNGX

Perfect for Ceramic Insert Multi Clamp

WDJN ➡F8

WDHN ➡F8

WDNN ➡F9

WVJN ➡F12

WVPN ➡F12

WVVN ➡F13

■ For General Turning

General Turning

Toolholders

F5

Lead Angle - - - -

Tooling

Insert shape

RNG RCGX / RPGX CDH

Perfect for Ceramic Insert

Clamp On CRGN ➡F16 VRAO ➡F18 VRAON ➡F19

BRV BRV ➡F17

Screw On HRCD ➡F20

Lead Angle 99° 91° 100°

Tooling

99° 91° 100°

Insert shape

VP.T TC.T / TC.W / TFT TN..

No offset Screw On SVXP-N ➡J32 STAC-N ➡J33 PTXN ➡J34

Lead Angle 95° 93° 62°30' 91° 93° 72°30'

Tooling

95° 93°62° 30'62° 30' 91° 91°

72° 30'

Insert shape

CC.T / CC.W DC.T / DC.W / TFD DC.T / DC.W VC.T / VC.W / TFV VC.T / VC.W

No offset Screw On SCLC ➡J26

SDJC ➡J28

SDNCN ➡J28

SVAC-N ➡J31

SVJC ➡J31

SVVCR-N ➡J31

■ For Swiss-type Lathes (With no offset)

● Y-Axis holders and DS-Holders are also available!

General Turning

Toolholders

F6

General Turning Toolholders

・ Right hand shown

95°

WCLN

CCLN

Inserts(CNG) ➡ E3        Inserts(CNGA) ➡ E4・E5・E22・E30Inserts(CNGX) ➡ E6        

Inserts(CNG) ➡ E3Inserts(CNGX) ➡ E6

● Inch / Metric Holders

Item NumberStock

Insert*R L (inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)

WCLN 16-4D ● ● 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.25 ― CNGA 43(CNGA 45)(CNG 43)(CNG 45)(CNGX 43)(CNGX 45)

WCLN 20-4D ● ● 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.25 ―WCLN 2525M12 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 32WCLN 3225P12 ○ ○ ― 32 ― 25 ― 170 ― 32 ― 32 ― 32

● Inch Holders

Item NumberStock Dimensions (inch)

Insert*R L

CCLN 164 CX ● ● 1.00 1.00 6.00 1.00 1.25 1.34 CNGX 45(CNGX 43)(CNG 45)(CNG 43)CCLN 204 CX ● ● 1.25 1.25 6.00 1.25 1.50 1.34

● Spare PartsInsert Clamp Blade Shim Shim Screw Wrench

CNGX 432415 ―

ICSN454 (OP)

1160 LW-4Standard CNGX 45 ICSN434

CNG 432417 (OP) 9414 (OP)

ICSN454 (OP)CNG 45 INSN434

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard CNGA 43DC6CN

ACN423×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-D

CNGA 45 ACN423×1CNG 43 TC6CN

(OP)ACN423×2

CNG 45 ACN423×1CNGX 43 HC6CN

(OP)ACN423×2

CNGX 45 ACN423×1

95°

・ Right hand shown

CN.. Inserts

●:Stock  ○: 1-2 week delivery  OP:Optional parts

General Turning

Toolholders

F7

WCBN

● Inch / Metric Holders

Item NumberStock

Insert*R L (inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)

WCBN 16-4D 1.00 ― 1.00 ― 6.00 ― 1.00 ― .88 ― 1.25 ―CNGA 43(CNGA 45)(CNG 43)(CNG 45)

WCBN 20-4D 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.13 ― 1.25 ―

WCBN 2525M12 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 22 ― 32

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard CNGA 43DC6CN

ACN423×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-DCNGA 45 ACN423×1CNG 43 TC6CN

(OP)ACN423×2

CNG 45 ACN423×1

75°

・ Right hand shown

* Optional spare parts are required to use the inserts in parentheses. See spare parts lists for detail.

Inserts(CNG) ➡ E3        Inserts(CNGA) ➡ E4・E5・E22・E30

General Turning

Toolholders

F8

General Turning Toolholders

WDJN

● Inch / Metric Holders

Item NumberStock

Insert*R L (inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)

WDJN 16-4D ● ● 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.50 ―DNGA 43(DNGA 45)(DNGX 45)

WDJN 20-4D ● ● 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.50 ―WDJN 2525M15 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 38WDJN 3225P15 ○ ○ ― 32 ― 25 ― 170 ― 32 ― 32 ― 38

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard DNGA 43DC6DN

ADN423×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-DDNGA 45 ADN423×1

DNGX 45 HC6DN(OP) ADN423×1

93°

・ Right hand shown

WDHN

● Inch / Metric Holders

Item NumberStock

Insert*R L (inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)

WDHN 16-4D 1.00 ― 1.25 ― 6.00 ― 1.00 ― 1.25 ― 1.38 ―DNGA 43(DNGA 45)(DNGX 45)

WDHN 20-4D 1.00 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.38 ―WDHN 2525M15 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 35

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard DNGA 43DC6DN

ADN423×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-DDNGA 45 ADN423×1

DNGX 45 HC6DN(OP) ADN423×1

107°30'

・ Right hand shown

DN.. Inserts

●:Stock  ○: 1-2 week delivery  OP:Optional parts

Inserts(DNGA) ➡ E7・E23   Inserts(DNGX) ➡ E8・E35・E36

Inserts(DNGA) ➡ E7・E23   Inserts(DNGX) ➡ E8・E35・E36

General Turning

Toolholders

F9

WDNN

● Inch / Metric Holders

Item Number Stock Insert*(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)(inch)(㎜)

WDNNN 16-4D 1.00 ― 1.00 ― 6.00 ― 1.00 ― .500 ― 1.67 ―DNGA 43(DNGA 45)(DNGX 45)

WDNNN 20-4D 1.25 ― 1.25 ― 6.00 ― 1.25 ― .625 ― 1.67 ―WDNNN 2525M15 ○ ― 25 ― 25 ― 150 ― 25 ― 12.5 ― 42.5

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard DNGA 43DC6DN

ADN423×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-DDNGA 45 ADN423×1

DNGX 45 HC6DN(OP) ADN423×1

10°

62°30'

* Optional spare parts are required to use the inserts in parentheses. See spare parts lists for detail.

Inserts(DNGA) ➡ E7・E23   Inserts(DNGX) ➡ E8・E35・E36 G

eneral Turning

Toolholders

F10

General Turning Toolholders

・ Right hand shown

75°

CSKN

● Inch Holders

Item NumberStock Dimensions (inch)

Insert*R L

CSKN 164 CX ● ● 1.00 1.00 6.00 1.00 1.25 1.34 SNGX 45(SNG 43)(SNG 45)CSKN 204 CX ● ● 1.25 1.25 6.00 1.25 1.50 1.34

CSKN 165 CX ● ● 1.00 1.00 6.00 1.00 1.25 1.34 SNGX 55(SNG 55)CSKN 205 CX ● ● 1.25 1.25 6.00 1.25 1.50 1.34

CSSN

・ Right hand shown75°

CSRN

● Inch Holders

Item NumberStock Dimensions (inch)

Insert*R L

CSRN 164 CX ● ● 1.00 1.00 6.00 1.00 1.13 1.34 SNGX 45(SNG 43)(SNG 45)CSRN 204 CX ● ● 1.25 1.25 6.00 1.25 1.38 1.34

CSRN 165 CX ● ● 1.00 1.00 6.00 1.00 1.10 1.50SNGX 55(SNG 55)CSRN 205 CX ● ● 1.25 1.25 6.00 1.25 1.35 1.50

CSRN 245 CX ● ● 1.50 1.50 8.00 1.50 1.75 1.65

● Inch Holders

Item NumberStock Dimensions (inch)

Insert*R L

CSSN 245 CD ● ● 1.50 1.50 6.00 1.50 2.00 1.653 SNGX 55(SNG 55)

● Spare PartsInsert Clamp Blade Shim Shim Screw Wrench

Standard SNGX 45 2415 ― ISSN 4341160

LW-4SNG 43

2417 (OP) 9414 (OP)ISSN 454 (OP)

SNG 45 ISSN 434Standard SNGX 55 2415 ―

ISSN534 1180SNG 55 2417 (OP) 9414 (OP)

45°・ Right hand shown

SN.. Inserts

●:Stock  ○: 1-2 week delivery  OP:Optional parts Inserts(SNG)  ➡ E13・E41Inserts(SNGX) ➡ E15   

General Turning

Toolholders

F11

WSDN

45°

・ Right hand shown

45°

WSSN

● Inch / Metric Holders

Item NumberStock

Insert*R L inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WSSN 16-4D 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.38 ― SNGA 43(SNGA 45)(SNG 43)(SNG 45)(SNGX 45)

WSSN 20-4D 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.38 ―WSSN 2525M12 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 35

Item Number Stock Insert*inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WSDNN 16-4D 1.00 ― 1.00 ― 6.00 ― 1.00 ― .500 ― 1.42 ― SNGA 43(SNGA 45)(SNG 43)(SNG 45)(SNGX 45)

WSDNN 20-4D 1.25 ― 1.25 ― 6.00 ― 1.25 ― .625 ― 1.42 ―WSDNN 2525M12 ○ ― 25 ― 25 ― 150 ― 25 ― 12.5 ― 35WSDNN 3225P12 ○ ― 32 ― 25 ― 170 ― 32 ― 12.5 ― 35

● Spare PartsInsert Clamp Shim Clamp Screw Wrench

(for Clamp Screw) Shim Screw Wrench (for Shim Screw) Spring

Standard SNGA 43DC6CN

ASN423×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-DSNGA 45 ASN423×1SNG 43 TC6CN

(OP)ASN423×2

SNG 45 ASN423×1SNGX 45 HC6SN (OP) ASN423×1

CSDN

● Inch Holders

Item Number StockDimensions (inch)

Insert*

CSDNN 164 CX ● 1.00 1.00 6.00 1.00 1.65 SNGX 45(SNG 43)(SNG 45)CSDNN 204 CX ● 1.25 1.25 6.00 1.25 1.65

CSDNN 165 CX ● 1.00 1.00 6.00 1.00 1.65 SNGX 55(SNG 55)CSDNN 205 CX ● 1.25 1.25 6.00 1.25 1.65

● Spare Parts Insert Clamp Blade Shim Shim Screw Wrench

Standard SNGX 45 2415 ― ISSN 4341160

LW-4SNG 43

2417 (OP) 9414 (OP)ISSN 454 (OP)

SNG 45 ISSN 434Standard SNGX 55 2415 ―

ISSN534 1180SNG 55 2417 (OP) 9414 (OP)

* Optional spare parts are required to use the inserts in parentheses. See spare parts lists for detail.

Inserts(SNG)  ➡ E13・E41Inserts(SNGX) ➡ E15   

Inserts(SNG) ➡ E13・E41      Inserts(SNGA) ➡ E14・E24・E40・E41Inserts(SNGX) ➡ E15         

General Turning

Toolholders

F12

General Turning Toolholders

WVJN

● Inch / Metric Holders

Item NumberStock

Insert*R L inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WVJN 16-3D ● ● 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.61 ―

VNGA 33(VNGA 35)(VNGX 35)

WVJN 20-3D ● ● 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.61 ―

WVJN 2525M16 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 41

WVJN 3225P16 ○ ○ ― 32 ― 25 ― 170 ― 32 ― 32 ― 41

Inserts(VNGA) ➡ E20・E26・E50

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard VNGA 33DC6VN

AVN323×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-DVNGA 35 AVN323×1

VNGX 35 HC6VN(OP) AVN323×1

13°

93°

・ Right hand shown

WVPN

● Inch / Metric Holders

Item NumberStock

Insert*R L inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WVPN 16-3D 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.38 ―VNGA 33(VNGA 35)(VNGX 35)

WVPN 20-3D 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.38 ―

WVPN 2525M16 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 35

Inserts(VNGA) ➡ E20・E26・E50

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard VNGA 33DC6VN

AVN323×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-DVNGA 35 AVN323×1

VNGX 35 HC6VN(OP) AVN323×1

10°

10°

117°30'

2

・ Right hand shown

VN.. Inserts

●:Stock  ○: 1-2 week delivery  OP:Optional parts

General Turning

Toolholders

F13

WVVN

● Inch / Metric Holders

Item Number Stock Insert*inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WVVNN 16-3D 1.00 ― 1.00 ― 6.00 ― 1.00 ― .500 ― 1.73 ―VNGA 33(VNGA 35)(VNGX 35)

WVVNN 20-3D 1.25 ― 1.25 ― 6.00 ― 1.25 ― .625 ― 1.73 ―

WVVNN 2525M16 ○ ― 25 ― 25 ― 150 ― 25 ― 12.5 ― 44

Inserts(VNGA) ➡ E20・E26・E50

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard VNGA 33DC6VN

AVN323×2

AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-DVNGA 35 AVN323×1

VNGX 35 HC6VN(OP) AVN323×1

15°

72°30'

* Optional spare parts are required to use the inserts in parentheses. See spare parts lists for detail.

General Turning

Toolholders

F14

General Turning Toolholders

WTGN

● Inch / Metric Holders

Item NumberStock

Insert*R L inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WTGN 16-3D 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.00 ― TNGA 33(TNGA 35)(TNG 33)(TNG 35)

WTGN 20-3D 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.00 ―

WTGN 2525M16 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 35

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard TNGA 33DC5TN

ATN323×2

AOS-5*26W LLR-T15 FSS15-3.0*12 LLR-T10 ASGL6-DTNGA 35 ATN323×1TNG 33 TC5TN

(OP)ATN323×2

TNG 35 ATN323×1

・ Right hand shown

91°

WTFN

● Inch / Metric Holders

Item NumberStock

Insert*R L inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WTFN 16-3D 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.06 ― TNGA 33(TNGA 35)(TNG 33)(TNG 35)

WTFN 20-3D 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.06 ―

WTFN 2525M16 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 27

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard TNGA 33DC5TN

ATN323×2

AOS-5*26W LLR-T15 FSS15-3.0*12 LLR-T10 ASGL6-DTNGA 35 ATN323×1TNG 33 TC5TN

(OP)ATN323×2

TNG 35 ATN323×1

91°

・ Right hand shown

TN.. Inserts

●:Stock  ○: 1-2 week delivery  OP:Optional parts

Inserts(TNG) ➡ E16            Inserts(TNGA) ➡ E18・E25・E44・E45・E46

Inserts(TNG) ➡ E16            Inserts(TNGA) ➡ E18・E25・E44・E45・E46

General Turning

Toolholders

F15

WWLN-2

95°

・ Right hand shown

95°

・ Right hand shown

WWLN

● Inch / Metric Holders

Item NumberStock

InsertR L inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WWLN 16-4D 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.30 ―

WNGA 43(WNGA 45)WWLN 20-4D 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.30 ―

WWLN 2525M08 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 33

Item NumberStock

InsertR L inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜ inch ㎜

WWLN 16-4D-2 1.00 ― 1.00 ― 6.00 ― 1.00 ― 1.25 ― 1.18 ―WNGA 43(WNGA 45)WWLN 20-4D-2 1.25 ― 1.25 ― 6.00 ― 1.25 ― 1.50 ― 1.18 ―

WWLN 2525M08-2 ○ ○ ― 25 ― 25 ― 150 ― 25 ― 32 ― 30

Inserts ➡ E21・E51

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard WNGA 43DC6CN

AWN423-W×2AOS-6*30W LLR-T20 FSS15-3.0*12 LLR-T10 ASGL6-D

WNGA 45 AWN423-W×1

95°

WN.. Inserts

* Optional spare parts are required to use the inserts in parentheses. See spare parts lists for detail.

General Turning

Toolholders

F16

General Turning Toolholders

・ Right hand shown

CRGN

Inserts ➡ E10

● Inch Holders

Item NumberStock Dimensions (inch)

Insert*R L

CRGN 164 CD ● ● 1.00 1.00 6.00 1.00 1.25 1.34 RNG 45(RNG 43)CRGN 204 CD ● ● 1.25 1.25 6.00 1.25 1.50 1.34

CRGN 165 CD ● ● 1.00 1.00 6.00 1.00 1.25 1.34RNG 55

CRGN 205 CD ● ● 1.25 1.25 6.00 1.25 1.50 1.34

CRGN 206 CD ● ● 1.25 1.25 6.00 1.25 1.50 1.65 RNG 65

● Spare PartsInsert Clamp Blade Shim Shim Screw Wrench

Standard RNG 452413

9414

IRSN 431160

LW-4RNG 43 IRSN 45 (OP)

Standard RNG 55 IRSN 53 1180Standard RNG 65 2417 3919 1182

RN.. Inserts

●:Stock  ○: 1-2 week delivery  OP:Optional parts

General Turning

Toolholders

F17

・ Right hand shown

Radial mounting

Axial mountingAnvil

Shank

Clamp

BRV

Inserts(RCGX) ➡ E9 Inserts(RPGX)  ➡ E11

●Toolholder body

Item Number StockDimensions (inch)

Anvil Screw Stock

BS 20 ● 1.25 1.38 5.5 BAS 20 ●

● Anvils and Parts (Order each part separately)

Shank AnvilStock Dimensions (inch)

Insert Clamp Shim Clamp Screw

Shim ScrewR L

BS 20

BRVR 6020-2V ● .750 RCGX 23RPGX 23 BRCR-2V BN-2V BRCS 2V BNS-2V

BRVR 8020-3V ● 1.000 RCGX 35RPGX 35 BRCN-3V BN-3V BRCS 3V BNS-3V

BRVR 9020-4V ● 1.125 RCGX 45RPGX 45 BRCN-4V BN-4V BRCS 4V BNS-4V

BRVL 6020-2V ○ .750 RCGX 23RPGX 23 BRCL-2V BN-2V BRCS 2V BNS-2V

BRVL 8020-3V ● 1.000 RCGX 35RPGX 35 BRCN-3V BN-3V BRCS 3V BNS-3V

BRVL 9020-4V ● 1.125 RCGX 45RPGX 45 BRCN-4V BN-4V BRCS 4V BNS-4V

Note: Shank comes with anvil screws. - Order anvil separately.

RC.. / RP.. Inserts

* Optional spare parts are required to use the inserts in parentheses. See spare parts lists for detail.

General Turning

Toolholders

F18

General Turning Toolholders

・ Right hand shown

VRAO

● Inch Holders

Item NumberStock Dimensions (inch)

InsertR L

VRAO 16-2D ● ● 1.00 1.00 6.00 1.00 1.00 RCGX 102RCGX 23RCGX 25RPGX 23RPGX 25VRAO 20-2D ● ● 1.25 1.25 6.00 1.25 1.00

VRAO 16-3D ● ● 1.00 1.00 6.00 1.00 1.25RCGX 103RCGX 35RPGX 35

VRAO 20-3D ● ● 1.25 1.25 6.00 1.25 1.25

VRAO 24-3E ● ● 1.50 1.50 7.00 1.50 1.25

VRAO 16-4D ● ● 1.00 1.00 6.00 1.00 1.50RCGX 104RCGX 45RPGX 45

VRAO 20-4D ● ● 1.25 1.25 6.00 1.25 1.50

VRAO 24-4E ● ● 1.50 1.50 7.00 1.50 1.50

● Spare PartsParts

Toolholder

Clamp Shim Clamp Screw Shim Screw

VRAO 16-2DCL2RV SM2RV(RCGX10. / R.GX.5)

SM2RVS(R.GX23)(OP) SC40F-16 SC02C-08VRAO 20-2D

VRAO 16-3D

CL3RV SM3RV SC10F-10

SC05C-08

VRAO 20-3DSC05C-10

VRAO 24-3E

VRAO 16-4D

CL4RV SM4RV SC40F-12

SC06C-08

VRAO 20-4DSC06C-10

VRAO 24-4E

RC.. / RP.. Inserts

●:Stock  ○: 1-2 week delivery  OP:Optional parts

Inserts(RCGX) ➡ E9 Inserts(RPGX)  ➡ E11

General Turning

Toolholders

F19

VRAON

● Inch Holders

Item Number StockDimensions (inch)

Insert

VRAON 16-2D ● 1.00 1.00 6.00 1.00 RCGX 102RCGX 23RCGX 25RPGX 23RPGX 25VRAON 20-2D ● 1.25 1.25 6.00 1.00

VRAON 16-3D ● 1.00 1.00 6.00 1.25RCGX 103RCGX 35RPGX 35

VRAON 20-3D ● 1.25 1.25 6.00 1.25

VRAON 24-3E ● 1.50 1.50 7.00 1.25

VRAON 16-4D ● 1.00 1.00 6.00 1.50RCGX 104RCGX 45RPGX 45

VRAON 20-4D ● 1.25 1.25 6.00 1.50

VRAON 24-4E ● 1.50 1.50 7.00 1.50

● Spare PartsParts

Toolholder

Clamp Shim Clamp Screw Shim Screw

VRAON 16-2DCL2RV SM2RV(RCGX10. / R.GX.5)

SM2RVS(R.GX23)(OP) SC40F-16 SC02C-08VRAON 20-2D

VRAON 16-3D

CL3RV SM3RV SC10F-10

SC05C-08

VRAON 20-3DSC05C-10

VRAON 24-3E

VRAON 16-4D

CL4RV SM4RV SC40F-12

SC06C-08

VRAON 20-4DSC06C-10

VRAON 24-4E

Inserts(RCGX) ➡ E9 Inserts(RPGX)  ➡ E11

General Turning

Toolholders

F20

General Turning Toolholders

HRCD

● Metric Holders

Item NumberStock Dimensions (㎜)

InsertR

HRCD-22 ○ 50 50 300 50 30 CDH 22

HRCD-33 ○ 50 50 300 50 30 CDH 33

HRCD-42 50 50 300 50 30 CDH 42

HRCD-43 50 50 300 50 30 CDH 43

HRCD-53 50 50 300 50 30 CDH 53

● Spare PartsParts

Toolholder

Clamp Screw Washer Shim Wrench

HRCD-22 CS0316 W120 HACDH22 LW-2.5

HRCD-33 CS0625 W110 HACDH33 LW-5

HRCD-42 1/4-20UNC×11/4W106

HACDH42LWU-4

HRCD-43 1/4-20UNC×11/2 HACDH43

HRCD-53 3/8-16UNC×11/2 W107 HACDH53 LWU-5

CDH.. Inserts

●:Stock  ○: 1-2 week delivery  

Inserts ➡ E2

General Turning

Toolholders

G1

ID Tooling

●Product Lines ……………………… G2●For CN.. Inserts …………………… G4●For DN.. Inserts …………………… G4●For SN.. Inserts …………………… G5●For WN.. Inserts ………………… G5

G

ID Tooling

G2

NTK ID Tooling-Product Lines

■ Minimum bore diameter φ.039" -

For Conventional Lathes

For Swiss-type Lathes and Conventional Lathes

■ Multi-clamp seriesS-WCLN S-WDUN S-WSKN S-WWLN

Double clamp Double clamp Double clamp Double clamp

Min. Bore Dia:φ1.299" Min. Bore Dia:φ1.654" Min. Bore Dia:φ1.969" Min. Bore Dia:φ1.299"

S chipbreaker

Sharp cutting edge

H No chipbreaker

Mirror finish edge

F chipbreaker

Evacuates chips BACKWARD.

LBMA/LBMA-S DS-LBMB

Min. Bore Dia.:φ.039" Min. Bore Dia.:φ.039"

➡G5➡G5

➡J105

➡G4➡G4

➡J105

SBFS (Solid carbide bars)

Min. Bore Dia.:φ.079"

SHFS (Solid carbide bars)

Min. Bore Dia.:φ.079"

Hyper

➡J94➡J98

SBFB (Solid carbide bars)

Min. Bore Dia.:φ.079"

SHFB (Solid carbide bars)

Min. Bore Dia.:φ.079"

Hyper

➡J94➡J98

ID Tooling

G3

SBG BG (Steel shank) SFG

Min. Bore Dia.:φ.118" Min. Bore Dia.:φ.394" Min. Bore Dia.:φ.236"

■ Minimum Bore Diameter:φ.197" -

■ Back Boring

■ ID Grooving

■ ID Threading

C-MBR (Carbide shank) S-MBR (Steel shank) C-SEXR (Carbide shank) S-SEXR (Steel shank)

Min. Bore Dia.:φ.197" Min. Bore Dia.:φ.197" Min. Bore Dia.:φ.236" Min. Bore Dia.:φ.236"

C-STZ (Carbide shank)

Min. Bore Dia.:φ.394"

TGC (Carbide shank)HN59 (Steel shank)

    

Min. Bore Dia.:φ.315"

SBT

Min. Bore Dia.:φ.118"

C-STUC/P (Carbide shank) S-STUC/P (Steel shank) C-SCLC/P (Carbide shank) S-SCLC/P (Steel shank)

Min. Bore Dia.:φ.315" Min. Bore Dia.:φ.315" Min. Bore Dia.:φ.276" Min. Bore Dia.:φ.276"

➡J107

➡J108

➡J107

➡J108

➡J106

➡J109

➡J106

➡J109

➡J100

➡J112 ➡J101

➡J109

MMMMMMMMMMOOOOOOOOOOOOOGGGGGGGGGGGGGMMMMMMMMMMOOOOOOOOOOOGGGGGGGGGGGUUUUUUUUUULLLLLLLLLL BBBBBBBBBBBaaaaaaaaaarrrrrrrrrrrMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGGUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUULLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaarrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrNEWNEWNEW

➡J111 ➡J100ID Tooling

G4

ID Tooling■ CN.. Inserts

■ DN.. Inserts

S-WCLN

S-WDUN

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard CNGA 43DC6CN

ACN423×1

AOS-6*26W(S25R-WCLN 12)AOS-6*30W(Others)

LLR-T20

FSS16-3.0*8 LLR-T10

ASGL6-D

CNGA 45 ― ― ―CNG 43 TC6CN

(OP)ACN423×1 FSS16-3.0*8 LLR-T10

CNG 45 ― ― ―CNGX 43 HC6CN

(OP)ACN423×1 FSS16-3.0*8 LLR-T10

CNGX 45 ― ― ―

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard DNGA 43DC6DN

ADN423×1 AOS-6*26W(S32S-WDUN 15)AOS-6*30W

(S40T-WDUN 15)LLR-T20

FSS16-3.0*8 LLR-T10

ASGL6-DDNGA 45 ― ― ―

DNGX 45 HC6DN(OP) ― ― ―

6

95

6

3

● Metric Holders

Item NumberStock Min. Bore Dia.

(㎜)Dimensions (㎜)

Insert*R L

S25R-WCLN 12 ○ ○ 33 25 24 200 17 40 14 CNGA 43(CNGA 45)(CNG 43)(CNG 45)(CNGX 43)(CNGX 45)

S32S-WCLN 12 ○ ○ 40 32 30 250 22 50 12S40T-WCLN 12 ○ ○ 50 40 38 300 27 60 10S50U-WCLN 12 ○ ○ 63 50 47 350 35 65 8

● Metric Holders

Item NumberStock Min. Bore Dia.

(㎜)Dimensions (㎜)

Insert*R L

S32S-WDUN 15 ○ ○ 42 32 30 250 22 50 12 DNGA 43(DNGA 45)(DNGX 45)S40T-WDUN 15 ○ ○ 50 40 38 300 27 60 10

Min. Bore Diameter φ1.299" -

Min. Bore Diameter φ1.654" -

・ Right hand shown

・ Right hand shown

●:Stock  ○: 1-2 week delivery  OP:Optional parts

Inserts(CNG) ➡ E3        Inserts(CNGA) ➡ E4・E5・E22・E30Inserts(CNGX) ➡ E6        

Inserts(DNGA) ➡ E7・E23   Inserts(DNGX) ➡ E8・E35・E36

ID Tooling

G5

■ SN.. Inserts

■ WN.. Inserts

S-WSKN

S-WWLN

Inserts ➡ E21・E51

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard SNGA 43DC6CN

ASN423×1

AOS-6*30W LLR-T20

FSS16-3.0*8 LLR-T10

ASGL6-D

SNGA 45 ― ― ―SNG 43 TC6CN

(OP)ASN423×1 FSS16-3.0*8 LLR-T10

SNG 45 ― ― ―

SNGX 45 HC6CN(OP) ― ― ―

● Spare Parts

Insert Clamp Shim Clamp Screw Wrench (for Clamp Screw) Shim Screw Wrench

(for Shim Screw) Spring

Standard WNGA 43DC6CN

AWN423-W×1AOS-6*30W LLR-T20

FSS16-3.0*8 LLR-T10ASGL6-D

WNGA 45 ― ― ―

675

6

95

● Metric Holder

Item NumberStock Min. Bore Dia.

(㎜)Dimensions (㎜)

Insert*R L

S40T-WSKN 12 ○ ○ 50 40 38 300 27 60 10

SNGA 43(SNGA 45)(SNG 43)(SNG 45)(SNGX 45)

● Metric Holders

Item NumberStock Min. Bore Dia.

(㎜)Dimensions (㎜)

InsertR L

S25R-WWLN 08 ○ ○ 33 25 24 200 17 40 14WNGA 43

(WNGA 45)S32S-WWLN 08 ○ ○ 40 32 30 250 22 50 12S40T-WWLN 08 ○ ○ 50 40 38 300 27 60 10

Min. Bore Diameter φ1.969" -

Min. Bore Diameter φ1.299" -

・ Right hand shown

・ Right hand shown

* Optional spare parts are required to use the inserts in parentheses. See spare parts lists for detail.

Inserts(SNG) ➡ E13・E41      Inserts(SNGA) ➡ E14・E24・E40・E41Inserts(SNGX) ➡ E15         

ID Tooling

MEMO

H1

Grooving Tools

●Product Lines ……………………… H2● Guideline for Grooving  Heat Resistant Alloys …………… H4●For VGW Inserts ………………… H6●For VDB Inserts ………………… H8●For GKN / GKP / RKN Inserts H11●For VGE Inserts ………………… H12

H

Grooving

H2

Grooving Toolsfor General Machining

DB (Face Grooving)

➡H10Blade width .125" to .375"Depth of cut .750"

VDB

BGV

➡H7Blade width .125" to .375"Depth of cut .375" to 1.125"

VGW

DB(Straight OD) VGT NS

➡H9 ➡H12 ➡H11Blade width .125" to .375" Blade width .115" to .378" Blade width .031" to .189"Depth of cut .750" Depth of cut .470" Depth of cut .021"

VDB VGE GKN, GKP, RKN

Grooving

H3

for Swiss-type Lathes■ Grooving

■ Face Grooving

GTT DS-GTTL GTVW GTPA

➡J69 ➡J70 ➡J71 ➡J72Blade width .012" to .118" Blade width .012" to .118" Blade width .118" to .236" Blade width .079" to .098"Depth of cut .012" to .106" Depth of cut .012" to .106" Depth of cut .244" to .315" Depth of cut .197" to .236"

Y-axis holders available ➡J70 Y-axis holders available ➡J72GTMH32, GTMX32, GTM32 GVW GTPA

CSV

➡J73Blade width .010" to .059"Depth of cut .006" to .102"

CSVG

■ ID GroovingSBG BG SFG

➡J100 ➡J111 ➡J100Blade width .020" to .079" Blade width .020" to .079" Blade width .039" to .118"Depth of cut .031" to .087" Depth of cut .047" to .126" Depth of cut .059" to .118"Min. Bore Dia. φ.118" Min. Bore Dia. φ.394" Min. Bore Dia. φ.236"

CH-FGV DS-FGV FGV

➡J77 ➡J77 ➡J77Blade width .039" to .079" Blade width .039" to .079" Blade width .039" to .079"Depth of cut .059" to .157" Depth of cut .059" to .157" Depth of cut .059" to .118"

FGV, FBV FGV, FBV FGV

Grooving

H4

Guideline for grooving heat resistant alloys

Now available SX7 !

When using SX7 / SX5, increase feed rates 100% vs. Whisker Ceramics

SiAlON Ceramic Whisker Ceramic

SX5 SX7 WA1

Toughness

Flank wear resistance

Notching resistance

better

better

better

Application Grade CoolantCutting speed Feed

400 600 800 1000 1200 .002 .004 .006 .008 .010

Grooving SX7SX5 WET 900 (600-1200) SFM .006 (.004-.008) IPR

WA1900 (600-1200) SFM .002 (.002-.004) IPR

Grooving

H5

BGV Toololder System

● BGV toolholder is a flexible modular tooling system designed for ceramic grooving inserts with V-bottoms  This system provides excellent index repeatability and rigid clamping

● This BGV tool shank offers the flexibility and economy of a 4-way-use

When machining a grooved area with multiple passes, during the last remaining plunge the insert radius engages a potentially work hardened area. This programming procedure sets up the potential of corner radius chipping or notching.

The grooving insert is plunged down both outside walls thus maintaining a good finish. The remaining material can be removed by using a stronger insert shape such as a RCGX style.

Features

■ Application Information

≧45° Work HardeningLayer

45°

Change to

Grooving

H6

Grooving Tools

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number W R T LSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

VGW 41251 EX001 .125 .015 .187 .500 ●VGW 41251 T0220 .125 .015 .187 .500 ●VGW 41252 EX001 .125 .031 .187 .500 ●VGW 41252 T0220 .125 .031 .187 .500 ●VGW 41561 EX001 .156 .015 .187 .500 ●VGW 41561 T0220 .156 .015 .187 .500 ●VGW 41562 EX001 .156 .031 .187 .500 ●VGW 41562 T0220 .156 .031 .187 .500 ●VGW 41871 EX001 .187 .015 .187 .500 ●VGW 41871 T0220 .187 .015 .187 .500 ● ●VGW 41872 EX001 .187 .031 .187 .500 ●VGW 41872 T0220 .187 .031 .187 .500 ● ●VGW 62501 T0220 .250 .015 .250 .750 ● ●VGW 62501 T0420 .250 .015 .250 .750 ●VGW 62501 Z0220 .250 .015 .250 .750 ●VGW 62501 Z0420 .250 .015 .250 .750 ●VGW 62502 EX001 .250 .031 .250 .750 ●VGW 62502 T0220 .250 .031 .250 .750 ● ●VGW 62503 EX001 .250 .046 .250 .750 ●VGW 62503 T0220 .250 .046 .250 .750 ● ●VGW 62814 T0220 .250 .062 .250 .750 ●VGW 83122 EX001 .312 .031 .337 1.000 ●VGW 83122 T0220 .312 .031 .337 1.000 ●VGW 83124 EX001 .312 .062 .337 1.000 ●VGW 83124 T0220 .312 .062 .337 1.000 ● ●VGW 83752 EX001 .375 .031 .337 1.000 ●VGW 83752 T0220 .375 .031 .337 1.000 ● ●VGW 83754 EX001 .375 .062 .337 1.000 ●VGW 83754 T0220 .375 .062 .337 1.000 ● ● ●

90°T

W

R

L

■ VGW

Holders ➡ H7■ VGW..R

Holders ➡ H7

90°T

W

R

LSteel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number W R T LSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

VGW 4125R EX001 .125 .063 .187 .500 ●VGW 4125R T0220 .125 .063 .187 .500 ●VGW 4156R EX001 .156 .078 .187 .500 ●VGW 4156R T0220 .156 .078 .187 .500 ● ●VGW 4156R Z0820 .156 .078 .187 .500 ●VGW 4187R EX001 .187 .094 .187 .500 ●VGW 4187R T0220 .187 .094 .187 .500 ● ●VGW 6218R EX001 .218 .109 .250 .750 ●VGW 6218R T0220 .218 .109 .250 .750 ●VGW 6250R EX001 .250 .125 .250 .750 ●VGW 6250R T0220 .250 .125 .250 .750 ● ●VGW 8312R EX001 .312 .156 .337 1.000 ●VGW 8312R T0220 .312 .156 .337 1.000 ● ●VGW 8375R EX001 .375 .188 .337 1.000 ●VGW 8375R T0220 .375 .188 .337 1.000 ● ●

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery

Grooving

H7

Axial mounting

Radial mounting

Anvil

Shank

Clamp

BGV

● Toolholder Body

Item Number Stock

Dimensions (inch)Insert Anvil Screw Stock

BS 20 ● 1.25 1.38 5.5 VGWVGW..R BAS 20 ●

● Anvils(Anvil comes with clamp & clamp screw)Right hand

Shank Item NumberStock Dimensions (inch)

Insert Clamp Stock Clamp Screw StockR L

BS 20

BGVR 043020 ● ― .375 VGW 4125VGW 4156 BGCR 04 ●

BRCS 2V ●

BGVR 054520 ● ― .562 VGW 4156VGW 4187 BGCR 05 ●

BGVR 074520 ● ― .562 VGW 6218VGW 6250 BGCR 07 ●

BGVR 086020 ● ― .750 VGW 6250VGW 6281 BGCR 08 ●

BGVR 106020 ● ― .750 VGW 8312VGW 8344 BGCR 10 ●

BGVR 119020 ● ― 1.125 VGW 8344VGW 8375 BGCR 11 ●

Left hand

Shank Item NumberStock Dimensions (inch)

Insert Clamp Stock Clamp Screw StockR L

BS 20

BGVL 043020 ― ● .375 VGW4125VGW4156 BGCL 04 ●

BRCS 2V ●

BGVL 054520 ― ● .562 VGW4156VGW4187 BGCL 05 ●

BGVL 074520 ― ● .562 VGW6218VGW6250 BGCL 07 ●

BGVL 086020 ― ● .750 VGW6250VGW6281 BGCL 08 ●

BGVL 106020 ― ● .750 VGW8312VGW8344 BGCL 10 ●

BGVL 119020 ― ● 1.125 VGW8344VGW8375 BGCL 11 ●

Note: The holder body comes with anvil screws. Anvils sold separately

・ Right hand shown

Inserts ➡ H6

Grooving

H8

Grooving Tools■ VDB

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number W R S TSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

VDB 125 A015 T0225 .125 .015 .106 .250 ●VDB 156 A015 T0225 .156 .015 .106 .250 ●VDB 188 A015 T0225 .188 .015 .144 .250 ●VDB 218 A015 T0225 .218 .015 .144 .250 ●VDB 250 B015 T0225 .250 .015 .202 .337 ●VDB 250 B031 T0220 .250 .031 .202 .337 ● ● ●VDB 250 B062 T0220 .250 .062 .202 .337 ●VDB 281 B015 T0225 .281 .015 .202 .337 ●VDB 312 B015 T0225 .312 .015 .202 .337 ●VDB 312 B031 EX001 .312 .031 .202 .337 ●VDB 312 B031 T0220 .312 .031 .202 .337 ●VDB 312 B062 EX001 .312 .062 .202 .337 ●VDB 312 B062 T0220 .312 .062 .202 .337 ●VDB 344 B015 T0225 .344 .015 .275 .337 ●VDB 375 B015 T0225 .375 .015 .275 .337 ●VDB 375 B031 EX001 .375 .031 .275 .337 ●VDB 375 B031 T0220 .375 .031 .275 .337 ●VDB 375 B046 E02 .375 .046 .275 .337 ●VDB 375 B046 T0220 .375 .046 .275 .337 ●VDB 375 B062 E02 .375 .062 .275 .337 ●VDB 375 B062 T0220 .375 .062 .275 .337 ● ●

1.125

90°W

T

R S

■ VDB..R

Holders ➡ H9・H10

Holders ➡ H9・H10

1.125

90°W

T

R S

Steel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number W R S TSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

VDB 125 RA T0225 .125 .063 .106 .250 ●VDB 156 RA T0225 .156 .078 .106 .250 ●VDB 188 RA T0225 .188 .094 .144 .250 ●VDB 218 RA T0225 .218 .109 .144 .250 ●VDB 250 RB T0220 .250 .125 .202 .337 ● ●VDB 250 RB T0225 .250 .125 .202 .337 ●VDB 281 RB T0225 .281 .141 .202 .337 ●VDB 312 RB T0225 .312 .156 .202 .337 ●VDB 344 RB T0225 .344 .172 .275 .337 ●VDB 375 RB T0225 .375 .188 .275 .337 ●

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery

Grooving

H9

Anvil Shank

DB

● Toolholder Body

Item NumberStock Dimensions (inch)

Insert Anvil Screw Stock Clamp Screw StockR L

DB1-1-16 ● ● 1.00 1.00 6.00 .750VDBVDB..R DAS41 ● SC40F10 ●

DB1-1-20 ● ● 1.25 1.25 7.00 .750

Note: Toolholder body comes with anvil screw and clamp screw. Anvils and Clamps are sold separately

● Anvils and Clamps

InsertDB-1-16R(Right hand)

DB-1-16L(Left hand)

Anvil Stock Clamp Stock Anvil Stock Clamp StockVDB125 R1E04 ● CR1-1-E04 ● L1E04 ● CL1-1-E04 ●

VDB156 R1E05 ● CR1-1-E06 ● L1E05 ● CL1-1-E06 ●

VDB188 / VDB218 R1E06 ● CR1-1-E06 ● L1E06 ● CL1-1-E06 ●

VDB250 R1E07 ● CR1-1-E07 ● L1E07 ● CL1-1-E07 ●

VDB281 / VDB312 R1E09 ● CR1-1-E09 ● L1E09 ● CL1-1-E09 ●

VDB344 / VDB375 R1E11 ● CR1-1-E11 ● L1E11 ● CL1-1-E11 ●

InsertDB-1-20R(Right hand)

DB-1-20L(Left hand)

Anvil Stock Clamp Stock Anvil Stock Clamp StockVDB125 R2E04 ● CR1-1-E04 ● L2E04 ● CL1-1-E04 ●

VDB156 R2E05 ● CR1-1-E06 ● L2E05 ○ CL1-1-E06 ●

VDB188 / VDB218 R2E06 ● CR1-1-E06 ● L2E06 ● CL1-1-E06 ●

VDB250 R2E07 ● CR1-1-E07 ● L2E07 ● CL1-1-E07 ●

VDB281 / VDB312 R2E09 ● CR1-1-E09 ● L2E09 ● CL1-1-E09 ●

VDB344 / VDB375 R2E11 ● CR1-1-E11 ● L2E11 ● CL1-1-E11 ●

・ Right hand shown

Straight OD turning

Inserts ➡ H8

Grooving

H10

Grooving ToolsDB Face Grooving

Curve In Curve Out

CL

CL

RIGHT HAND

LEFT HAND

Clamp

Anvil Shank

(Max. Depth)CL

CL

RIGHT HANDClamp

Anvil Shank LEFT HAND

(Max. Depth)

● Toolholder Body

Item NumberStock Dimensions (inch)

Insert Anvil Screw Stock Clamp Screw StockR L

DB7-1-7-16 ○ ○ 1.00 1.00 6.00 .750VDBVDB..R DAS41 ● SC40F10 ●

DB7-1-7-20 ○ ○ 1.25 1.25 7.00 .750

Note: Toolholder body comes with anvil screw and clamp screw. Anvils and Clamps are soid separately

● Anvils and Clamps

Curve In

Shank InsertO.D. range

Clamp Stock3" - 4 1/2" 4 1/2" - 7" 7" - 14" 14" and over

DB7-1-7-16RDB7-1-7-20R

VDB156 / VDB188 DBA-3305 ○ DBA-3405 ○ DBA-3505 ○ DBA-3605 ○ CR1-1-E06A ○

VDB250 DBA-3307 ○ DBA-3407 ○ DBA-3507 ○ DBA-3607 ○ CR1-1-E07A ●

VDB281 / VDB312 DBA-3309 ○ DBA-3309 ○ DBA-3509 ○ DBA-3509 ○ CR1-1-E09A ○

VDB344 / VDB375 DBA-3311 ○ DBA-3311 ○ DBA-3511 ○ DBA-3511 ○ CR1-1-E11A ●

DB7-1-7-16LDB7-1-7-20L

VDB156 / VDB188 DBA-7305 ○ DBA-7405 ○ DBA-7505 ○ DBA-7605 ○ CL1-1-E06A ○

VDB250 DBA-7307 ○ DBA-7407 ○ DBA-7507 ○ DBA-7607 ○ CL1-1-E07A ●

VDB281 / VDB312 DBA-7309 ○ DBA-7309 ○ DBA-7509 ○ DBA-7509 ○ CL1-1-E09A ○

VDB344 / VDB375 DBA-7311 ○ DBA-7311 ○ DBA-7511 ○ DBA-7511 ○ CL1-1-E11A ○

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery

・ Right hand shown ・ Right hand shown

Curve Out

Shank InsertO.D. range

Clamp Stock3" - 4 1/2" 4 1/2" - 7" 7" - 14" 14" and over

DB7-1-7-16RDB7-1-7-20R

VDB156 / VDB188 DBA-4305 ○ DBA-4405 ○ DBA-4505 ○ DBA-4605 ○ CR1-1-E06A ○

VDB250 DBA-4307 ○ DBA-4407 ○ DBA-4507 ○ DBA-4607 ○ CR1-1-E07A ●

VDB281 / VDB312 DBA-4309 ○ DBA-4309 ○ DBA-4509 ○ DBA-4509 ○ CR1-1-E09A ○

VDB344 / VDB375 DBA-4311 ○ DBA-4311 ○ DBA-4511 ○ DBA-4511 ○ CR1-1-E11A ●

DB7-1-7-16LDB7-1-7-20L

VDB156 / VDB188 DBA-8305 ○ DBA-8405 ○ DBA-8505 ○ DBA-8605 ○ CL1-1-E06A ○

VDB250 DBA-8307 ○ DBA-8407 ○ DBA-8507 ○ DBA-8607 ○ CL1-1-E07A ●

VDB281 / VDB312 DBA-8309 ○ DBA-8309 ○ DBA-8509 ○ DBA-8509 ○ CL1-1-E09A ○

VDB344 / VDB375 DBA-8311 ○ DBA-8311 ○ DBA-8511 ○ DBA-8511 ○ CL1-1-E11A ○

Inserts ➡ H8

Grooving

H11

(Max. Depth)NS

■ GKN / GKPSteel P ● ●Stainless Steel M ● ●Cast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material N ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ●

Item Number W R DSilicon Nitride SiAlON Alumina Alumina - TiC Cermet PVD

SX1

SX6

SP2

SP9

SX5

SX7

SX9

HC1

HW2

HC2

HC6

HC7

ZC4

ZC7

C7X

QM3

GKP 3031 .031 .004 .050 ● ●GKP 3047 .047 .008 .075 ●GKN 3062 .062 .008 .094 ● ●GKP 3062 .062 .008 .094 ● ●GKP 3088 .088 .008 .094 ●GKN 3094 .094 .008 .150 ● ●GKP 3094 .094 .008 .150 ● ●GKN 3125 .125 .012 .150 ● ●GKP 3125 .125 .008 .150 ● ●GKN 3156 .156 .012 .150 ●GKP 3156 .156 .008 .150 ● ●GKN 3189 .189 .012 .150 ●GKP 3189 .189 .012 .150 ● ●

WD

.195

.344

.405φ3/855°

■ RKNSteel PStainless Steel MCast Iron K ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●Non-Ferrous Material NHeat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ● ● ● ●

Item Number W R DSilicon Nitride SiAlON Whisker Alumina Alumina - TiC

SX1

SX6

SP2

SP9

SX5

SX7

SX9

WA1

HC1

HW2

HC2

HC5

HC6

HC7

ZC4

ZC7

RKN 3078 .078 .039 .150 ●RKN 3094 .094 .047 .150 ●RKN 3125 .125 .063 .150 ●RKN 3156 .156 .078 .150 ●RKN 3189 .189 .095 .150 R

WD

.195

.344

55° .405φ3/8

* Inserts with special width and R in both GKN and GKP are available upon requests. Holders ➡ H11

● Toolholders

Item Number StockDimensions (inch)

Insert Clamp Stock Clamp Screw Stock

NSR16-3D ● 1.00 1.00 6.00 1.25 1.25 0.210GKN3..RRKN3..RGKP3..R

CM-72 S-412

NSL16-3D ● 1.00 1.00 6.00 1.25 1.25 0.210GKN3..LRKN3..LGKP3..L

CM-73 S-412

Inserts ➡ H11

Holders ➡ H11

Grooving

H12

Grooving Tools

Clamp-on type

(Max. depth)

1.0

VGT

● Toolholders

Item NumberStock Groove size covered Dimensions (inch)

InsertR L Width

VGT 16-3 ● ● .115 ~ .153 1.0 1.0 6.0 32 1.18 .470VGEVGT 16-4 ● ● .154 ~ .220 1.0 1.0 6.0 32 1.18 .470

VGT 16-6 ● ● .221 ~ .292 1.0 1.0 6.0 32 1.18 .470

● Spare Parts

Holder

Clamp Clamp screw Spring Wrench

Stock

Stock Stock Stock

R L

VGT 16-3 CV 3N ○ ○AOB-6N ○ ASG-6 ○ LW-4 ●VGT 16-4 CV 4N ○ ●

VGT 16-6 CV 6 ○ ○

■ VGE

●:1st Choice ●: Alternate choice●:Stock ○: 1-2 week delivery

・ Right hand shown

.787

W R 90°

T

Steel P ● ● ● ● ● ● ● ● ● ● ● ●Stainless Steel M ● ● ● ● ● ● ● ● ● ● ● ●Cast Iron K ● ● ● ●Non-Ferrous Material N ● ● ● ● ● ● ●Heat Resistant Alloy S ● ● ● ●Hardened Material H ● ● ●

Item Number W R T

Cermet CarbidePVD Coated PVD Coated CVD

XT3

C7X

XN4

Q15

C7Z

KM1

DM4

DT4

TM4

QM3

VM1

ZM3

CP1

VGE 125N008 .125 .008 .205 ●VGE 125N015 .125 .015 .205 ●VGE 156N015 .156 .015 .335 ●VGE 188N015 .188 .015 .335 ●VGE 250N015 .250 .015 .335 ●

Inserts ➡ H12

Holders ➡ H12

Grooving

Ⅰ1

Milling Cutters

●Overview …………………………… Ⅰ2● Milling with NTK Grades by Application ………………………… Ⅰ3● For Heat Resistant Alloys and Hardened Materials ……………… Ⅰ4●For Gray / Ductile Cast Iron … Ⅰ6●For Aluminum ………………… Ⅰ18

I

Milling Cutter

Ⅰ2

Milling Cutters

Features

Features

Features

Features

● High performance milling cutter line that uses round-shaped inserts for machining both aerospace and hardened steels

● SX7, the new SiAlON grade, has the best performance for high speed machining of high temperature alloys

● Extremely economical 8-corner inserts● Covers various applications with 45, 75, and 88 degree angle milling cutter● Ceramic inserts with chipbreaker and wiper are also available

● Positive inserts reduce tool pressure and bring excellent surface finish with long tool life● Best for milling thin parts thanks to the low tool pressure

● Large DOC is possible because of the fine pitch of inserts which results in higher productivity

● LNX Insert comes with special chipbreaker to reduce tool pressure

ccel igh speed illccel igh speed ill series

igh elocity illigh elocity ill series treme eed illtreme eed ill series

igh speed hear illigh speed hear ill series series

utteruttererformanceerformanceighigh series

Features

● Capable of 90-degree shoulder milling

● A variety of cutter diameters as small as .787 (φ20mm)

➡Ⅰ4・Ⅰ5

➡Ⅰ18

➡Ⅰ6-Ⅰ11

➡Ⅰ14-Ⅰ16

➡Ⅰ12

➡Ⅰ17

Features

● A wide range of cutter diameters from φ.787" (20mm) to  φ3.937" (100mm)● Excellent rigidity steel body ● With the fixed-type cutters, no time-consuming presetting is required

Heat Resistant Alloys and Hardened Materials

Gray / Ductile cast iron

Aluminum

Milling Cutter

Ⅰ3

■ General Guidelines for Successful Milling

● Select the best grade for the application

● Select cutter diameter 1.5 times greaterthan the workpiece width

● Eliminate any overhang to increase stability

● Choose the strongest nose radius

● No Coolant. Use compressed air

● Check clamp and part rigidity

Heat resistant alloy / PH stainless steel● Down or climb milling where the chip thins upon exit is the preferred method for HNBA materials

● Reduce feed rate 50% upon entrance and exit● Do not recut side walls as this can cause work hardening

● Use balanced shell mill adapter or shrink fit for end-mills

● As DOC gets thinner the feed must be increased to compensate for heat loss

● Use RPG geometries if tool pressure is a problem

Hardened Steel / Die mold /Chilled iron / Overlay● Larger edge preparations need to be used● Speed is reduced as hardness goes up

Cast iron / Ductile cast iron ● Parts that are cast are more difficult to machine than forged ・ decrease feed rates by 25%

● Maximize feed rates for gray cast irons

● Trouble shooting

Material Insert Grade NTK Grade ProblemSolution

Speed Feed DOC Edge Prep. Insert Grade Others

StainlessSteel Cermet C7X

Chipping ― ➡ ― ― ― ―

BUE ➡ ― ― ― ― ―

Break ― ➡ ➡ ― ― ―

Hardened Steel Ceramic HC7

WA1Chipping ― ➡ ― Wider ― ―

Break ➡ ➡ ― ― ― ―

Cast Iron SiliconNitride

SX1SX6SP9

Chipping ➡ ➡ ― Wider ― ―

Break ➡ ➡ ➡ ― Tougher Larger radius

Themal Crack ➡ ➡ ― ― ― ―

Crater Wear ― ― ― Sharper ― ―

HeatResistant Alloy

SiAlONSX5SX9SX7

Notching ➡ ➡ Vary /➡ Wider ― Pre-chamfer parts

Flank Wear ➡ ➡ ― ― Harder ―

Chipping ― ― Wider Tougher ―

Break ➡ ― ➡ ― Tougher ―

Tool Pressure ― ― ― ― ― Use RPG insert

Milling with NTK Grades by Application

■ Guidelines for Successful Milling by Material

Milling Cutter

Ⅰ4

Milling Cutters

●:Stock ○: 1-2 week delivery

● Inch size cutters

Item Number StockDimensions (inch)

Clamp Clamp Screw Weight(lbs) Insert

φRPIW075E075R02 ● 2 .750 .750 3.270 1.220 AMS-3 AOB-3S 0.4 RPG 21.5RPIW100E100R03 ● 3 1.000 1.000 3.270 1.000 AMS-4 AOB-4S 0.6 RPG 32RPIW125E125R03 ● 3 1.250 1.250 4.000 1.640

AMS-5T AOB-5S-T251.1

RPG 43RPIW150E150R03 ● 3 1.500 1.500 4.000 1.830 1.6

● Inch size cutters

Item Number StockDimensions (inch)

Shim Shim Screw Clamp Clamp Screw A.R. R.R. Weight

(lbs) Insertφ

RPIW200S075R04 ● 4 2.00 2.00 .750 .322 .748 .222ARP42A M3*8 AMS-5T AOB-

5S-T25 +5° +5° 0.9

RPG 43RPIW300S100R05 ● 5 3.00 2.00 1.000 .387 .748 .244 +5° +5° 2.0

●Metric size cutters

Item Number StockDimensions (㎜)

Shim Shim Screw Clamp Clamp Screw A.R. R.R. Weight

(㎏) Insertφ

JRPMW050S220R04 ○ 4 50 50 22 10.4 20 6.3ARP42A M3*8 AMS-5T AOB-

5S-T25

+5° +5° 0.4RPG 43JRPMW063S220R04 ○ 4 63 50 22 10.4 20 6.3 +5° +5° 0.6

JRPMW080S254R05 ○ 5 80 50 25.4 9.5 25 6.0 +5° +2°30′ 0.9

● Metric size cutters

Item Number StockDimensions (㎜)

Clamp Clamp Screw Weight(㎏) Insert

φJRPMW032E250R03 ○

332 25

120 40 AMS-5T AOB-5S-T250.4

RPG 43JRPMW032E320R03 ○ 32 32 0.6JRPMW040E320R03 ○ 40 32 0.7

H

φD2

φD1

L2

A.R.+5°R.R.‒7°30'

ccel igh speed illccel igh speed ill series

W

H

φD2

φD1

L2

L1

A.R.+5°R.R.‒2°30'~ ‒5°

* Recommend using torque wrench @35lbs(4Nm)

Milling Cutter

Ⅰ5

● Inch size cutters

Item Number StockDimensions (inch)

Clamp Clamp Screw Weight(lbs) Insert

φ φRNIW200S075R03 ● 3 2.000 2.000 .750 .322 .748 .203

AMS-6T AOB-6S-T301.0

RNG 45RNIW250S075R04 ● 4 2.500 2.000 .750 .322 .748 .222 1.3RNIW300S100R05 ● 5 3.000 2.000 1.000 .387 .748 .244 1.6

● Metric size cutters

Item Number StockDimensions (㎜)

Clamp Clamp Screw Weight(㎏) Insert

φ φJRNMW050S220R03 ○ 3 50 50 22 10.4 20 6.3

AMS-6T AOB-6S-T300.4

RNG 45JRNMW063S220R04 ○ 4 63 50 22 10.4 20 6.3 0.6JRNMW080S254R05 ○ 5 80 50 25.4 9.5 25 6.0 0.9

W

H

φD2

φD1

L2

L1

A.R.‒5°R.R.‒10°

● Recommend Cutting Conditions

Work Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)200 700 1200 1700 2200 2700 3200 3700 .002 .003 .004 .005 .006 .007

S SX7 ● ‒.150

Heat Resistant Alloys

SX5/SX9 ● ‒.150

WA1 ● ‒.150

H WA1 ● ○ ‒.150

Hardened Steel

HRC45-55 HC7 ● ○ ‒.150

HRC55-65

WA1 ● ○ ‒.150

HC7 ● ○ ‒.150

Inserts (RNG) ➡ E10Inserts (RPG) ➡ E11

Milling Cutter

Ⅰ6

Milling Cutters

●:Stock ○: 1-2 week delivery

igh elocity illigh elocity ill series

Insert

● Inch size cuttersItem Number Stock

Dimensions (inch) Weight(lbs) Insert

φ φ φ φ φJFDX25IN-45-06R ● 6 2.500 3.129 2.000 .315 .750 .315 2.362 .669 .445 2.2

SNG 43

JFDX30IN-45-08R ● 8 3.000 3.629 2.000 .315 1.000 .387 2.362 .827 .445 2.8JFDX40IN-45-10R ● 10 4.000 4.629 2.000 .315 1.500 .640 3.150 2.000 .535 3.9JFDX50IN-45-12R 12 5.000 5.629 2.000 .315 1.500 .640 3.740 2.000 .535 4.1

● Metric size cuttersItem Number Stock

Dimensions (㎜) Weight(㎏) Insert

φ φ φ φ φJFDX063-45-06R ○ 6 63 72 50 8 22.0 10.4 58 18 10.5 0.9

SNG 43

JFDX080-45-08R ○ 8 80 95 50 8 25.4 9.5 62 36 10.5 1.2JFDX080MM-45-08R ● 8 80 95 50 8 27.0 12.4 64 19 10.5 1.3JFDX100-45-10R ○ 10 100 120 50 8 31.75 12.7 62 45 8.5 1.7JFDX100MM-45-10R ● 10 100 120 50 8 32.0 14.4 64 45 8.5 1.5JFDX125-45-12R ○ 12 125 146 58 8 38.1 15.9 83 55 13.5 2.8JFDX125MM-45-12R ● 12 125 146 58 8 40.0 16.4 85 55 13.5 2.9

● Spare Parts

Wedge Wedge Screw Torx Wrench Shim Shim Screw

① ② ③ ④

T15 T15HLW175 WS0616-T15 T-15A ASN423 M3×8

12.5 6.3

Lead angle

θθ:45°

● Lead angle 45 degree -SN43〈A.R. -6° R.R. -10°〉

φW

ag

H

45°

dφd2

φD2φD1

φc

Milling Cutter

Ⅰ7

● Inserts

Shape Dimensions (inch) Item Number RSilicon Nitride Whisker Cermet

SX1

SX6

SP9

WA1

C7X

12.5

1/2 3/16R

SNG 432 T0220 .031 ●SNG 432 T0420 .031 ● ● ● ● ●SNG 433 T0220 .047 ●SNG 433 T0420 .047 ● ● ● ● ●SNG 434 T0220 .063 ●SNG 434 T0420 .063 ● ● ● ● ●

12.5 .40

1/2 3/16R

SNGF 433 TRCC413 .047 ● ●

SNGF 433 RT0425 C421 .047 ●

6.3

3/16

45°R150 0.64

.079

1/2R0.5

SNG 43AN TW ― ● ●

The insert must be installed in all insert pockets

● CBN Wiper InsertDimensions (inch) Item Number R CBN

B30 B52

3/16.480

45°

.630

R9.84 .087

(.189)

.059FDX 1204-45-50R ― ● ●

For θ=45°

● Recommend Cutting ConditionsWork Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)700 1200 1700 2200 2700 3200 3700 4200 .002 .004 .006 .008 .010 .012

K SX1 ● ○ ‒.220

Gray Cast Iron

SX6 ● ● ‒.220

SP9 ● ○ ‒.220

Ductile IronSP9 ● ○ ‒.220

C7X ● ○ ‒.220

Work Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)200 400 600 800 1000 1200 1400 1600 .002 .004 .006 .008 .010 .012

P C7X ● ○ ‒.150Stainless Steel

M

C7X ● ○‒.120

Carbon SteelAlloy Steel ‒.040

* Recommend using torque wrench @35lbs(4Nm)

with chipbreaker

with wiper

Reduce tool pressure

Reduce tool pressure

Inserts (SNG) ➡ E13・E41

(300- BHN)

(-300 BHN)

Milling Cutter

Ⅰ8

Milling Cutters

●:Stock ○: 1-2 week delivery

igh elocity illigh elocity ill series

● Inch size cuttersItem Number Stock

Dimensions (inch) Weight(lbs) Insert

φ φ φ φ φJFDX25IN-75-06R ● 6 2.500 2.732 2.000 .472 .750 .315 2.362 .669 .760 2.0

SNG 43

JFDX30IN-75-08R ● 8 3.000 3.232 2.000 .472 1.000 .387 2.362 .827 .760 2.2JFDX40IN-75-10R ● 10 4.000 4.232 2.000 .472 1.500 .640 3.150 2.000 .850 3.3JFDX50IN-75-12R ● 12 5.000 5.232 2.000 .472 1.500 .640 3.740 2.000 .850 5.7

● Metric size cuttersItem Number Stock

Dimensions (㎜) Weight(㎏) Insert

φ φ φ φ φJFDX063-75-06R ○ 6 63 70 50 12 22.0 10.4 58 18 18.5 0.8

SNG 43

JFDX080-75-08R ○ 8 80 87 50 12 25.4 9.5 62 36 15.5 1.1JFDX080MM-75-08R 8 80 87 50 12 27.0 12.4 64 19 15.5 1.1JFDX100-75-10R ○ 10 100 107 50 12 31.75 12.7 62 45 16.5 1.4JFDX100MM-75-10R 10 100 107 50 12 32.0 14.4 64 45 23.5 1.3JFDX125-75-12R ○ 12 125 132 58 12 38.1 15.9 83 55 21.5 2.6JFDX125MM-75-12R 12 125 132 58 12 40.0 16.4 85 55 26.5 2.3JFDX160-75-16R 16 160 166 60 12 50.8 19 100 72 20.5 4.1

12.5 6.3

θ:75°

Lead angle

θ

● Lead angle 75 degree -SN43〈A.R. -6° R.R. -10°〉

● Spare Parts

Wedge Wedge Screw Torx Wrench Shim Shim Screw

① ② ③ ④

T15 T15HLW175 WS0616-T15 T-15A ASN423 M3×8

W

ag

H

75°

φdφd2

φD2φD1

φc

Insert

Milling Cutter

Ⅰ9

● CBN Wiper InsertDimensions (inch) Item Number R CBN

B30 B52

3/16

(.177)

1/2

.480

15° .543

R9.84

.049

.059FDX 1204-75-50R ― ● ●

For θ=75°

● Inserts

Shape Dimensions (inch) Item Number RSilicon Nitride Whisker Cermet

SX1

SX6

SP9

WA1

C7X

12.5

1/2 3/16R

SNG 432 T0220 .031 ●SNG 432 T0420 .031 ● ● ● ● ●SNG 433 T0220 .047 ●SNG 433 T0420 .047 ● ● ● ● ●SNG 434 T0220 .063 ●SNG 434 T0420 .063 ● ● ● ● ●

12.5 .40

1/2 3/16R

SNGF 433 TRCC413 .047 ● ●

SNGF 433 RT0425 C421 .047 ●

6.3

.055 .055

.031

45°75°

3/161/2

SNG 43EN TN ― ● ● ●

The insert must be installed in all insert pockets

● Recommend Cutting ConditionsWork Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)700 1200 1700 2200 2700 3200 3700 4200 .002 .004 .006 .008 .010 .012

K SX1 ● ○ ‒.220

Gray Cast Iron

SX6 ● ● ‒.220

SP9 ● ○ ‒.220

Ductile IronSP9 ● ○ ‒.220

C7X ● ○ ‒.220

Work Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)200 400 600 800 1000 1200 1400 1600 .002 .004 .006 .008 .010 .012

P C7X ● ○ ‒.150Stainless Steel

M

C7X ● ○‒.120

Carbon SteelAlloy Steel ‒.040

* Recommend using torque wrench @35lbs(4Nm)

with chipbreaker

with wiper

Reduce tool pressure

Reduce tool pressure

Inserts (SNG) ➡ E13・E41

(300- BHN)

(-300 BHN)

Milling Cutter

Ⅰ10

Milling Cutters

●:Stock ○: 1-2 week delivery

igh elocity illigh elocity ill series

● Inch size cuttersItem Number Stock

Dimensions (inch) Weight(lbs) Insert

φ φ φ φ φJFDX25IN-88-06R ● 6 2.500 2.531 2.000 .472 .750 .315 2.362 .669 .760 1.8

SNG 43

JFDX30IN-88-08R ● 8 3.000 3.031 2.000 .472 1.000 .387 2.362 .827 .760 2.1JFDX40IN-88-10R ● 10 4.000 4.031 2.000 .472 1.500 .640 3.150 2.000 .850 3.2JFDX50IN-88-12R ● 12 5.000 5.031 2.000 .472 1.500 .640 3.740 2.000 .850 5.8

● Metric size cuttersItem Number Stock

Dimensions (㎜) Weight(㎏) Insert

φ φ φ φ φJFDX063-88-06R ○ 6 63 64 50 12 22.0 10.4 58 18 13 0.8

SNG 43

JFDX080-88-08R ○ 8 80 81 50 12 25.4 9.5 62 36 13.5 1.0JFDX080MM-88-08R 8 80 81 50 12 27.0 12.4 64 19 13.5 1.1JFDX100-88-10R ○ 10 100 101 50 12 31.75 12.7 62 45 16.5 1.4JFDX100MM-88-10R 10 100 101 50 12 32.0 14.4 64 45 23.5 1.3JFDX125-88-12R ○ 12 125 126 58 12 38.1 15.9 83 55 21.5 2.6JFDX125MM-88-12R 12 125 126 58 12 40.0 16.4 85 55 26.5 2.5JFDX160-88-16R 16 160 156 60 12 50.8 19 100 72 20.5 4.1

12.5 6.3

θ:88°

Lead angle

θ

● Lead angle 88 degree -SN43〈A.R. -6° R.R. -10°〉

● Spare Parts

Wedge Wedge Screw Torx Wrench Shim Shim Screw

① ② ③ ④

T15 T15HLW175 WS0616-T15 T-15A ASN423 M3×8

Insert

W

ag

H

88°

φdφd2

φD2φD1

φc

Milling Cutter

Ⅰ11

● CBN Wiper InsertDimensions (inch) Item Number R CBN

B30 B52

3/16.480

R9.84

.242

.510

φ1/2

.010

.059

2° FDX 1204-88-50R ― ● ●

For θ=88°

● Inserts

Shape Dimensions (inch) Item Number RSilicon Nitride Whisker Cermet

SX1

SX6

SP9

WA1

C7X

12.5

1/2 3/16R

SNG 432 T0220 .031 ●SNG 432 T0420 .031 ● ● ● ● ●SNG 433 T0220 .047 ●SNG 433 T0420 .047 ● ● ● ● ●SNG 434 T0220 .063 ●SNG 434 T0420 .063 ● ● ● ● ●

12.5 .40

1/2 3/16R

SNGF 433 TRCC413 .047 ● ●

SNGF 433 RT0425 C421 .047 ●

6.3

3/161/2(.079)

R1.2

(.079)

.005

SNEN 1204ZN T01025 ― ● ●

The insert must be installed in all insert pockets

● Recommend Cutting ConditionsWork Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)700 1200 1700 2200 2700 3200 3700 4200 .002 .004 .006 .008 .010 .012

K SX1 ● ○ ‒.220

Gray Cast Iron

SX6 ● ● ‒.220

SP9 ● ○ ‒.220

Ductile IronSP9 ● ○ ‒.220

C7X ● ○ ‒.220

Work Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)200 400 600 800 1000 1200 1400 1600 .002 .004 .006 .008 .010 .012

P C7X ● ○ ‒.150Stainless Steel

M

C7X ● ○‒.120

Carbon SteelAlloy Steel ‒.040

* Recommend using torque wrench @35lbs(4Nm)

with chipbreaker

with wiper

Reduce tool pressure

Reduce tool pressure

Inserts (SNG) ➡ E13・E41

(300- BHN)

(-300 BHN)

Milling Cutter

Ⅰ12

Milling Cutters

●:Stock ○: 1-2 week delivery

● Metric size cuttersItem Number Stock

Dimensions (㎜) Weight(㎏) Insert

φ φ φ φ φJXTM080-88-10R ○ 10 80 83 50 14 25.4 9.5 58 36 14 1.1

LNX 324JXTM100-88-13R ○ 13 100 103 50 14 31.75 12.7 77 50 17 1.8JXTM125-88-16R ○ 16 125 128 58 14 38.1 15.9 77 55 22 3.1

● Inch size cuttersItem Number Stock

Dimensions (inch) Weight(lbs) Insert

φ φ φ φ φJXTM30IN-88-10R ● 10 3.000 3.041 2.000 .551 1.000 .387 2.362 .827 .539 2.4

LNX 324JXTM40IN-88-13R ● 13 4.000 4.041 2.000 .551 1.500 .640 3.150 2.000 .870 3.9JXTM50IN-88-16R 16 5.000 5.041 2.000 .551 1.500 .640 3.740 2.000 .870 6.5

● Lead angle 88 degress - LNX324 〈A.R.‒4°,R.R.0°〉

seriestreme eed illtreme eed ill

W

H

a

88°

φ

g

d2

φd

φD2φD1φc

Lead angle

θ

12.5

A.R.‒4°R.R.0°

θ:88°

● Spare PartsInsert Screw Wrench

LRIS-4*12 LLR-25S

● Screw Drivers (OP)Bit Handle Handle & Bit

HLR-25S XX2815-04 XX2815-04-25S

Milling Cutter

Ⅰ13

● InsertsItem Number R

Silicon NitrideSX1 SX6 SP9

LNX 324-02 T0420(LNX 324-08 T01020) .031 ● ● ○

LNX 324-03 T0420(LNX 324-12 T01020) .047 ● ● ○

LNX 324-04 T0420(LNX 324-16 T01020) .063 ● ● ○

3/8

.1615/8

150°R1/4

* Recommend using torque wrench @35lbs(4Nm)

● Recommend Cutting ConditionsWork Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)700 1200 1700 2200 2700 3200 3700 4200 .002 .004 .006 .008 .010 .012

K SX1 ● ○ ‒.300

Gray Cast Iron

SX6 ● ● ‒.300

SP9 ● ○ ‒.300

Ductile Iron SP9 ● ○ ‒.300

Milling Cutter

Ⅰ14

Milling Cutters

●:Stock ○: 1-2 week delivery

igh speed hear illigh speed hear ill series

● Metric size cutters

Item Number StockDimensions (㎜) Weight

(㎏) Insertφ φ φ φ φ

JSDW080-45-06R ○ 6 80 95.0 50 6.6 25.4 9.5 62 36 18 1.1

SDCW 43JSDW100-45-07R ○ 7 100 120.4 50 6.6 31.75 12.7 58 45 16 1.4JSDW125-45-08R ○ 8 125 145.8 58 6.6 38.1 15.9 79 55 21 2.6

● CBN Wiper Insert

Shape Item NumberCBN

B30 B523/16.480

45°

R9.84 φ1/2

.094

(.189)

.059 SDW 1204-45-50R ● ●

● Spare Parts

Insert Screw Torx Wrench

FSI21-5.0*12.45 T-20

● Inch size cutters

Item Number StockDimensions (inch) Weight

(lbs) Insertφ φ φ φ φ

A300R100-SDW43-6C ● 6 3.000 3.740 2.000 .260 1.000 .387 2.290 .820 .787 2.3

SDCW 43A400R150-SDW43-7C ● 7 4.000 4.740 2.000 .260 1.500 .640 3.200 2.000 .875 3.3A500R150-SDW43-8C ● 8 5.000 5.740 2.000 .260 1.500 .640 3.810 2.120 .871 5.0

θ:45°

For θ=45°

T20

● Lead angle 45 degress - SDW43 〈A.R.+12°,R.R.0°〉

Lead angle

θ

W

H

a45°

φD1

φD2

φd

g

φd2

φc

● Inserts

Item Number R Fig.Silicon Nitride Cermet

SX1 SX6 SP9 C7X

SDCW 432 T0420 .031 1 ● ● ○ ●

SDCW 433 T0420 .047 1 ● ● ●

SDCW 434 T0420 .063 1 ● ● ●

SDCW 43AE T0420* ― 2 ● ● ○ ●Fig.2: SDCW43AEFig.1: SDCW43

.004

1/2

45°

3/16

.216

15°

1/2 R

15°

.216

3/16

* The insert must be installed in all insert pockets * Recommend using torque wrench @35lbs(4Nm)

● Recommend Cutting Conditions

Work Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)700 1200 1700 2200 2700 3200 3700 4200 .002 .004 .006 .008 .010 .012

K SX1 ● ○ ‒.200

Gray Cast Iron

SX6 ● ● ‒.200

SP9 ● ○ ‒.200

Ductile Iron SP9 ● ○ ‒.200

with wiper

Inserts (SDCW) ➡ E12・E39

Milling Cutter

Ⅰ15

● Inserts

Item Number R Fig.Silicon Nitride Cermet

SX1 SX6 SP9 C7X

SDCW 432 T0420 .031 1 ● ● ○ ●

SDCW 433 T0420 .047 1 ● ● ●

SDCW 434 T0420 .063 1 ● ● ●

SDCW 43EE T0420R* ― 2 ● ● ○ ●

● Metric size cutters

Item Number StockDimensions (㎜) Weight

(㎏) Insertφ φ φ φ φ

JSDW063-75-04R ○ 4 63 70.6 50 9.1 22 10.4 58 18 14 0.8

SDCW 43

JSDW080-75-05R ○ 5 80 83.3 50 9.1 25.4 9.5 62 36 15.5 1.0JSDW100-75-06R ○ 6 100 108.7 50 9.1 31.75 12.7 58 45 16.5 1.3JSDW125-75-07R ○ 7 125 134.1 58 9.1 38.1 15.9 79 55 21.5 2.5JSDW160-75-10R 10 160 165 68 9.1 50.8 19 100 72 28.5 4.0

● CBN Wiper Insert

Shape Item NumberCBN

B30 B523/16.480

R9.8415°

(.193)

.052.059

φ1/2

SDW 1204-75-50R ○ ○

● Spare Parts

Insert Screw Torx Wrench

FSI21-5.0*12.45 T-20

● Inch size cutters

Item Number StockDimensions (inch) Weight

(lbs) Insertφ φ φ φ φ

E250R100-SDW43-4C ● 4 2.500 2.780 2.000 .360 1.000 .387 2.290 .820 .787 1.9

SDCW 43

E300R100-SDW43-5C ● 5 3.000 3.280 2.000 .360 1.000 .387 2.290 .820 .787 2.4E400R150-SDW43-6C ● 6 4.000 4.280 2.000 .360 1.500 .640 3.200 2.000 .875 3.7E500R150-SDW43-7C ● 7 5.000 5.280 2.000 .360 1.500 .640 3.200 2.000 .875 5.4

θ:75°

For θ=75°

T20

● Lead angle 75 degress - SDW43 〈A.R.+12°,R.R.0°〉

Lead angle

θ

Fig.2: SDCW43EEFig.1: SDCW43

.055

1/2

75° .216

15°

3/161/2 R

15°

.216

3/16

W

H

a75°

φD1φD2

φd

g

φd2

φc

* The insert must be installed in all insert pockets * Recommend using torque wrench @35lbs(4Nm)

● Recommend Cutting Conditions

Work Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)700 1200 1700 2200 2700 3200 3700 4200 .002 .004 .006 .008 .010 .012

K SX1 ● ○ ‒.220

Gray Cast Iron

SX6 ● ● ‒.220

SP9 ● ○ ‒.220

Ductile Iron SP9 ● ○ ‒.220

with wiper

Inserts (SDCW) ➡ E12・E39

Milling Cutter

Ⅰ16

Milling Cutters

●:Stock ○: 1-2 week delivery

igh speed hear illigh speed hear ill series

● Spare Parts

Insert Screw Torx Wrench

FSI21-5.0*12.45 T-20

● Inch size cutters

Item Number StockDimensions (inch) Weight

(lbs) Insertφ φ φ φ φ

P250R100-SDW43-4C ● 4 2.500 2.590 2.000 .400 1.000 .387 2.290 .820 .787 1.7

SDCW 43

P300R100-SDW43-6C ● 6 3.000 3.070 2.000 .400 1.000 .387 2.290 .820 .787 2.2P400R150-SDW43-8C ● 8 4.000 4.070 2.000 .400 1.500 .640 3.200 2.000 .875 3.5P500R150-SDW43-10C ● 10 5.000 5.070 2.000 .400 1.500 .640 3.200 2.000 .875 5.2

θ:88°

T20

● Lead angle 88 degress - SDW43 〈A.R.+12°,R.R.0°〉

Lead angle

θ

● Inserts

Item Number R Fig.Silicon Nitride Cermet

SX1 SX6 SP9 C7X

SDCW 432 T0420 .031 1 ● ● ○ ●

SDCW 433 T0420 .047 1 ● ● ●

SDCW 434 T0420 .063 1 ● ● ●

SDCW 43PE T0420R* .031 2 ● ● ●Fig.2: SDCW43PEFig.1: SDCW43

.081/2 R

88°

.216

15°

3/161/2 R

15°

.216

3/16

W

H

a88°

φD1φD2

φd

g

φd2

φc

* The insert must be installed in all insert pockets * Recommend using torque wrench @35lbs(4Nm)

● Recommend Cutting Conditions

Work Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)700 1200 1700 2200 2700 3200 3700 4200 .002 .004 .006 .008 .010 .012

K SX1 ● ○ ‒.220

Gray Cast Iron

SX6 ● ● ‒.220

SP9 ● ○ ‒.220

Ductile Iron SP9 ● ○ ‒.220

with wiper

Inserts (SDCW) ➡ E12・E39

Milling Cutter

Ⅰ17

W

H

ag

φdφd2

L2

φDφc

Lead angle

θ

12.5 6.3

θ:90°

a

φD φd

LL2

series

● JQTS Metric size cutters

Item Number StockDimensions (㎜) Weight

(㎏) A.R. R.R. Insert Screw Wrench Insertφ φ φ φ

JQTS040-90-4R ໐ 4 40 40 18 14 16 8.4 35 12 4.2 0.2 +6° -13°FSI22-4.0*11 T-15A APCW

1604JQTS050-90-5R ໐ 5 50 40 22 14 22 10.4 45 18 10.7 0.3 +6° -10°JQTS063-90-6R ໐ 6 63 50 22 14 22 10.4 58 18 14.5 1.4 +6° -12°

● JQTE Metric size cutters

Item Number StockDimensions (㎜) Weight

(㎏) A.R. R.R. Insert Screw Wrench Insertφ φ

JQTE020-90-1R ○ 1 20 100 30 14 20 0.2 +6° -13°FSI23-4.0*7

T-15AAPCW1604

JQTE025-90-2R ○ 2 25 100 30 14 25 0.3 +6° -13°JQTE032-90-3R ○ 3 32 110 35 14 32 0.5 +6° -13°

FSI22-4.0*11JQTE040-90-4R ○ 4 40 110 37 14 32 0.6 +6° -13°

● CBN Wiper InsertShape Item Number B30 B52

R.011

.354

3/16(.126)

R9.84

.290

.653

.059

φ3/8

φ.236

φ.173 APCW 1604 PDSRCE ○ ○

JQTSJQTE

● Recommend Cutting Conditions

Work Material Grade Dry Wet

Cutting Speed (SFM) Feed (IPT) Depth of Cut (inch)700 1200 1700 2200 2700 3200 3700 4200 .002 .004 .006 .008 .010 .012

K SX6 ● ○ ‒.320Gray Cast Iron SP9 ● ● ‒.320

Ductile Iron SP9 ● ○ ‒.320

● Inserts

Shape Item Number R mSilicon NitrideSX6 SP9

   

3/8 3/16

.648

R

φ.173

φ.236

φ3/8

m

APCW 160408 T01020 .031 .288 ○ ○

APCW 160412 T01020 .047 .286 ○ ○

APCW 160420 T01020 .079 .284 ○ ○

   

3/16

.648

R.031.102

3/8

φ.173

φ.236

φ3/8

m

APCW 1604 PDTR― ○ ○

The insert must be installed in all insert pockets with wiper

* Recommend using torque wrench @35lbs(4Nm)

Milling Cutter

Ⅰ18

Milling Cutters

●:Stock ○: 1-2 week delivery     OP:Optional parts

series Fixed type/Adjustable typeutteruttererformanceerformanceighigh

HPC (steel body) φ20 - φ100 (φ.787" - φ.3.937")

Figure-2: Shank type

Figure-1: Small diameter type

Figure-3: Shell type

Features

● A wide range of sizesThe diameters range from φ.787" - φ3.937" for the HPC series

● Excellent rigidity (HPC)The material for the HPC body is steel, achieving exceptional reliability

Figure 1 Small diameter type

φ φφ

A.R.+9° R.R.+4°

Figure 2 Shank type

φφ

A.R.+6° R.R.-3°~+3°

Figure 3 Shell type

A.R.+6° R.R.0°

φφφ φ

● Metric size Cutters

Figure Item number Stock φ φ φ φ φ Weight(㎏)

Max. RPM allowed (RPM)

Item number of applicable insert

Fixed type

1

RD020T20070R03 ○ 3 20 30 20 100 30 - - - - - - - 0.23 18,000

HDA4015R04 PD1

HDA4505R04 TM1

RD025T25070R03 ○ 3 25 40 25 110 40 - - - - - - - 0.37 18,000RD030T20060R04 ○ 4 30 60 20 120 35 - 25 - - - - - 0.33 18,000RD032T20060R04 ○ 4 32 60 20 120 35 - 26 - - - - - 0.36 18,000RD035T20060R04 ○ 4 35 60 20 120 35 - 28 - - - - - 0.36 18,000

2

RA040T20060R04K ○ 4 40 45 20 105 - - - - - - - - 0.45 18,000

HAL3515R04 PD1

HAT6021R04 PD1

HAN9521R04 TM1

HLA8521R04 TM1

RA040T25080R04K ○ 4 40 45 25 125 - - - - - - - - 0.6 18,000RA050T20060R05K ○ 5 50 45 20 105 - - - - - - - - 0.6 18,000RA050T25080R05K ○ 5 50 45 25 125 - - - - - - - - 0.75 18,000RA050T32080R05K ○ 5 50 45 32 125 - - - - - - - - 0.9 18,000

3

RA050C22.00R05K ○ 5 50 45 22 - - 20 - 10.4 6.3 42 18 11 0.4 18,000RA063C22.00R06K ○ 6 63 45 22 - - 20 - 10.4 6.3 42 18 11 0.73 18,000RA080A25.40R07K ○ 7 80 43 25.4 - - 26 - 9.5 6.0 50 38.9 15 0.95 15,000RA100A31.75R09K 9 100 45 31.75 - - 32 - 12.7 8.0 60 61 11 1.6 10,000

Adjustable type 2

RA040T20060R04 ○ 4 40 45 20 105 - - - - - - - - 0.45 18,000RA040T25080R04 ○ 4 40 45 25 125 - - - - - - - - 0.60 18,000RA050T20060R05 ○ 5 50 45 20 105 - - - - - - - - 0.60 18,000RA050T25080R05 ○ 5 50 45 25 125 - - - - - - - - 0.75 18,000RA050T32080R05 ○ 5 50 45 32 125 - - - - - - - - 0.90 18,000

3

RA050C22.00R05 ○ 5 50 45 22 - - 20 - 10.4 6.3 42 18 11 0.40 18,000RA063C22.00R06 ○ 6 63 45 22 - - 20 - 10.4 6.3 42 18 11 0.73 18,000RA080A25.40R07 ○ 7 80 43 25.4 - - 26 - 9.5 6.0 50 38.9 15 0.95 15,000RA100A31.75R09 ○ 9 100 45 31.75 - - 32 - 12.7 8.0 60 61 11 1.6 10,000

Milling Cutter

Ⅰ19

● Inserts

Shape Item number Corner angle w T Cutting edge

length A.R. R.R. WiperPCD PVD coated

carbideCutter Type

(figure)PD1 TM1W T

10

HDA4015R04 0° 6.7 3.4 4.0 +9° +4° 0.4 Provided ● 1

with chipbreaker

W T

10 HDA4505R04 0° 6.7 3.4 Min. 5.0 +9° +4° 0.4 Provided ○ 1

TWHAL3515R04

0° 10 4.0

3.5

+6° 0° 0.4 Provided

23

HAT6021R04 6.0 ●

W

11

T

HAN9521R04N 0° 10 4.0 Min. 6.0 +6° -3° 0.4 Provided ○ 23

W T

with chipbreaker

HLA8521R04 0° 10.078 4.0 Min. 6.0 +6° +3° 0.4 Provided ○ 23

● Spare Parts

Item number Cartridge Axial setscrew

Cartridge setscrew

Insert clamping screw Handle Torx

screwdriverHex-

screwdriverClamping bolt

RD020T20070R03 FSI0306A 2814HS(OP)

U107T10(OP)

RD025T25070R03 FSI0307ARD030T20060R04

RD032T20060R04

RD035T20060R04

RA040T20060R04/KRA06P03NC CS0510A CS0510T FSI035104A 2814HS

(OP)U107T15〈Torx〉(OP)

U104-40〈Hex〉(OP)

RA040T25080R04/K

RA050T20060R05/K

RA050T25080R05/K

RA050T32080R05/K

RA050C22.00R05/K CS1040A(OP)(coolant through)RA063C22.00R06/K

RA080A25.40R07/K MBC-M12(OP)

RA100A31.75R09/K MBC-M16(OP)

* Recommend using torque wrench @35lbs(4Nm)

Milling Cutter

MEMO

Sharp people

   Sharp ideas

     Sharp tools

www.youtube.com/ntkcuttingtoolswww.ntkcuttingtools.com

J1

For Swiss-type Lathes

●New Products ……………………… J2●CUT DUO ●BACK DUO ●Thread Whirling●CL Chipbreaker ●AMX Chipbreaker ●UL Chipbreaker●DS-ACH Holders ●Mogul Bar ●STICK DUO Hyper●Shifted Toolholders ●DS Sleeve ●SATURN DUO●Indexable End Mills

●Tooling …………………………… J13●General / Front Turning ……… J21●Back Turning ……………………… J39●Cut-off / Parting ………………… J51●Grooving …………………………… J63●Threading ………………………… J79●ID Tooling ………………………… J91●Indexable End Mills ………… J113●NTK Unique Tooling ………… J117

J

For Swiss-type Lathes

J2

New Products

●Offers excellent chip control andsuperior surface finishes due to a special molded chipbreaker and precision grinding

●Achieves rigid clamping because of a 3-V point clamping design

●Wide toolholder selection for various diameters

Chip control comparison

Features

NEW CUT DUO

Edge view Chip control

CTDPL12-20D20CTDP20N02 DM4

Stable chip control

Beginnig of machining End of machining

Competitor'sCarbide

Beginnig of machining End of machining

Work material:304 SS  Cutting condition:1750 RPM .002 IPR WET

100pcs

chipped

50pcs

Inserts ➡ J58Holders ➡ J58

.002 IPR .003 IPR .005 IPR

4140

304 SS

Chip control(260 SFM)

Surface finish

CUT DUO Competitor's 3D chipberaker

Special molded chipbreaker makes chip curl, and achive excellent chip control

Highly accurate grinding on each edge relief angle offers good sharpness and reduces cutting forces

chipping

For Swiss-type Lathes

[ N

ew Produ

cts ]

J3

NEW BACK DUO

Features

●New chipbreaker covers a wide range of cutting conditions●No-compromise quality back turning tools●High quality finish in a single pass●No finishing cut required ➡ Reduced cycle time●Multi point clamping system ensures rigidity

.079

.039

.118

.002 .004

BACK DUO

Feed(IPR)

D.O

.C(

inch)

304 SSBACK DUO Competitor

Feed (IPR).002 .003 .002 .003

Depth of cut(inch)

.118

Work material:304 SS  Holder:TBDPR12  Insert:TBDP2201MR TM4Cutting condition:26 SFM  (x)=.0008 IPR  (z)=.002 - .003 IPR .020"-.118" DOC WET

Incredible chip control Unstable chip control

1Pass BACK DUO Competitor

Diameter

End face

End face Diameter End face Diameter

Excellent surfaceRa:0.90μm

Rough surfaceRa:2.16μm

Rz :4.11μm Rz :10.28μm

Work material:304 SS  Holder:TBDPR12  Insert:TBDP2201MR TM4Cutting condition:26 SFM  (x)=.008 IPR  (z)=.003 IPR .118" DOC WET

New 3D chipbreaker

Surface finish comparison for 304 SS

Chip control comparison

Chip control range

Inserts ➡ J42Holders ➡ J42

Excellent surface with good chipcontrol

Improved surface finish thanks to wiper flat and precision grinding on cutting edge

Evacuates chips away from the shoulder

PAT.P

For Swiss-type Lathes

[ N

ew Produ

cts ]

J4

New Products

●Reduce cycle time by more than half*● .256" (6.5㎜ ) thick inserts accommodate large pitch and lead

* Applies to cycle time for thread whirling only Does not apply to total cycle time. Actual results may vary

NTK Thread Whirling - Nonstop improvement to meet tighter-than-ever demands from quality oriented customers

●Dramatically improved productivity in thread forming operations

●NTK's unique design technology (patented) makes precise and correct inserts possible, the first time, without any redesign and remake

●Excellent surface finish and longer tool life than competitors'

●Sharp cutting edges for reduced tool pressure and superior chip control

Features

Form multiple-lead threads in a single-pass

Double-lead threads Triple-lead threads

Work Bone screw Worm gear

Work material Ti-6Al-4V ELI brass

Work appearance

Insert appearance

Major Dia. φ.157"(4.0㎜) φ.278"(7.0㎜)

Minor Dia. φ.094"(2.4㎜) φ.185"(4.7㎜)

Pitch φ.135"(3.42㎜) φ.193"(4.9㎜)

Patented

NTK’s Unique Attachment System

Mutiple-Lead Thread Whirling

① Loosen the Mounting Bolts ② Rotate the Insert Holder to 10 degrees ③ Pull the Whirling Insert Holder without pull out the Mounting Bolts

Insert HolderMount Adapter

InsertInsert Holder Mounting Bolt

NTK’s whirling insert holder can be attached and detached without removing mounting bolts

Adapter Mounting Bolt

NEW Thread Whirling

Information ➡ J86

For Swiss-type Lathes

[ N

ew Produ

cts ]

J5

NEW CL Chipbreaker

Features

Up-sharp edge

●Sharpest NTK molded chipbreaker with excellent chip control

●Applicable for hard to cut work materials●Perfect choice for high precision machining●Covers extremely wide cutting range

.118

.079

.039

.0040 .006Feed (IPR)

Dep

th o

f cut

(in

ch)

CL

AZ7

ZR

Machining of 304 SS(Dry machining for filming purpose)

262 SFM .003 IPR .039" DOC

The combination of high rake angles and sharp cutting edges ensures burr free and stable precision machining

304 SS262 SFM, WET

.0008 IPR.039" DOC

.0010 IPR.039" DOC

.0020 IPR.039" DOC

CL chipbreaker【DCGT32.504MCL TM4】

Competitor's 3D chipbreaker

Inserts ➡ E28・E33・E49

Chip control comparison

Chip control

●Excellent chip control in wide range of cutting conditions

●Applicable for stainless steels to low carbon steels

For Swiss-type Lathes

[ N

ew Produ

cts ]

J6

New Products

NEW AMX Chipbreaker

●Excellent chip control for very light depth of cut where conventional chipbreakers will not work

●Perfect choice for Swiss style lathes and secondary-operation machines

Features

.039

.008

.004

.012

.002 .004 .006Feed (IPR)

Dep

th o

f cut

(in

ch)

AMX

AZ7ZR

Feed (IPR).0008 .0010 .0020

Dep

th o

f cut

inch

) .002

.004

.012

Work material:304 SS  Holder:SDJCR1010X07N  Insert:DCGT21.508MAMX TM4Cutting condition:328 SFM .008-.002 IPR .002"-.012" DOC WET

Chip control range

Chip control Incredible chip control !

Burr-free and improved microfinish due to sharp cutting edges

Control chips precisely even under light depth of cut and low feed rate

Inserts ➡ E33

For Swiss-type Lathes

[ N

ew Produ

cts ]

J7

NEW UL Chipbreaker

●Sharp edged negative inserts that cut like positives●Lower cost per corner than positive inserts

Features

②Covers wide cutting condition rangeWide coverage regardless of depth of cut and feed rate

UL

ZP

★★

★★

ZF1

.004.002 .006

.120

.080

.040

0

Depth of cut (Inch)

①Sharp edge with "double-positive" design

Breaker for heavy depth of cut

Breaker for light depth of cut

Cut chips and costs

■Toolholders for Swiss-type lathes

③Reduce cost in Swiss machining

Positive insert with sharp cutting edge is required for Swiss machining.

With UL chipbreaker, negative insert provides sharp cutting edge AND more corners.

《304 SS》 260 SFM WET

★ .001 IPR .020" DOC ★ .004 IPR .079" DOC

Square shank Offset "0" DS Holder, DS-ACH HolderInserts ➡ E44Holders ➡ J34

For Swiss-type Lathes

[ N

ew Produ

cts ]

J8

New Products

Range ofcenterline heightadjustment

0 - .008"00000000000000 -- .00000000000000000000000088888888888888""""

RRRRRRRaRaRaRaRaRaRaRaRaangngngngnggngngngnggnnngngngggggeeeeeeeeeee ffffffooofofoooooo

Adjustment wedge Insert edge moves up

Adjustment wedge goes down

Turn a screw clockwise

How to useInsert moves in an upward direction only. See the instruction shown on the back page. (Loosen wedge screw before making any adjustment)

① Install the holder slightly below centerline. Then take a facing test cut.

② Measure the diameter of the centerboss.

④Re-machine the end face.③ Raise the center height by one half of the diameter of the boss.

  Adjustment references are available in the tool case.*Adjustment instructions are supplied in the tool case

Patented

NEW DS-ACH Holders

●Adjust centerline height simply with a wrench

Features

Adjust centerline height easily●Eliminate center boss on end faces●Provide constant OD dimension●Adjust easily in machine

Optimized design reduces vibration

Improved chatter resistance.

DS-ACH type Conventional type

Excellent surface Chattered

Tested cutting conditions (304 SS)Work material:304 SSHolder:DS-SDUL19-11-ACHInsert:DCGT32.508MCL TM4Cutting condition: 250 SFM .002 IPR .079" DOC WET

2.76”(70 ㎜)Overhang

Holders ➡ J124・J125・J126

For Swiss-type Lathes

[ N

ew Produ

cts ]

J9

NEW Mogul Bar

4.0

3.2

2.4

1.6

0.8

.160 .240 .320 .400 .480 .560 .640 .720

L:Overhang amount (inch)

D:Shank diameter (inch)

Steel shankSteel shank

Carbide shankCarbide shankSteel Shank

Carbide Shank

L/D≦5

L/D≦7L:OverhangD:Shank diameter

[Cutting condition example] Work materials: Alloy steel, stainless 260 SFM, .002 - .004 IPR, .004" - .020" DOC WET

Vibration analysisMogulBar Other boring bars

Note: Assuming a 100N load is applied. Equal amount of force was applied to both bars for vibration analysis.Boring bar used in above analysis: S08H-STUPR09D10-OH

L/D=5

Reduced duration of vibration

● High rigidity + Minimal flat widths Reduce vibration

● Large clearance for improved chip evacuation

● All MogulBar boring bars are coolant through

●F chipbreakers allow chips to evacuate backward

●Combination of the F-chipbreak-ers and MogulBar delivers the best performance

DOC(inch)

Feed(IPR).002 .004

FG Chipbreaker● Best for finishing ● Works for small DOC(.020" or less)

● High rake angle

.004

.012

F1/F05 Chipbreakers●Cover wide condition range● Ground chipbreaker

.020

Note: Right-hand inserts with FG and F1 chipbreakers should be used with right-hand holders

[Cutting condition example]4140 Carbon Steel Diameter : φ.472"260 SFM Depth of Bore : .787" WetHolder : S10K-STUPR11D12-OH Insert : TPGH221

FG

F1・F05

Depth of cut (inch)

Feed rate (IPR)0 .002 .004 .006 .008

.012

.020

.040

.060

■ Recommended Cutting Condition Range

Holders ➡ J93

Features

Recommended amount of overhang

F Chipbreakers - Evacuate chips BACKWARD

F Chipbreakers - Features

For Swiss-type Lathes

[ N

ew Produ

cts ]

J10

New Products

NEW STICK DUO Hyper Hyper

● Indexable double-ended solid carbide ID tools  - No adjustment required for each index● Excellent repeatability in inserts and holders● Adjust overhang amount by adjusting internal ball screw● Wear resistant multi-layer PVD coating● Competitive price per corner performance

●Minimum bore diameter φ.087" -

●Coner R : .002"/.006"

●3 types lineupS.FS-S type

S.FB-F type

Control the chip to backward

Copy or recess maching possible Anti vibration

S.FS-H type

Mirror finish edge

Good chip controlNo scratch mark on a work piece

S.FB-F type

Control the chip to backward direction

S.FS-S type

Sharp edge

Wide area of chippocket

Back taper

Chipbreaker for sharp cutting

30°

f

L1

Offset f:±.0006"Tool Length L1:±.0008"

Y

Centerline Y: +.002"/-.000" Corner R:±.0006"

①Unstable depth(Including dimension on face)

Tool Length

Caused by tolerance in

Centerline height②Unstable ID at d1& d2

Corner R③Unstable finish and depth of cut

Offset④Unstable ID

Typical issues caused by poor tolerance

X Direction4

-2

-4 measurements

(m)

Deflection

1 2 3 4 5 6 7 8 9 10

Y Direction (Center height)4

-2

-4 measurements

(m)

Deflection

1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10

Z Direction (Length)4

-2

-4 measurements

(m)

Deflection

■ Workpiece

Inserts ➡ J94 Sleeves ➡ J96

Features

Application Example Tool Tolerance

Repeatability

Line up

For Swiss-type Lathes

[ N

ew Produ

cts ]

J11

1. Eliminate shims for turning holders when extended guide bushing is used (especially in thread whirling)

2. Perform finish cut without retracting roughed section (bar) to guide bushing

Two Major FeaturesShim

GangToolPost

GangToolPost

With NTK ShiftedTurning Toolholders●Feature 1 ●Feature 2

Typical turning With Shifted Holders:Finish turn can be done without retracting the roughed bar

With Conventional Holders:Roughed bar comes out when retracted for finish turn

No shims required during thread whirling operation with an extended guide bushing

● Prevents coolant and chips from damaging live tool stations● Takes DS Series holders to perform various back working● Designed exclusively for 22mm(.886") round shank stations● Compatible with 16mm(.630") round shank DS Series holders

Features

First Recommendation for Turning

× How it works

When DS holders are used directly in live tool stations, coolant and chips sneak in from the flat of holders to damage the live stations

By using the DS Sleeve, you can use the DS Series holders with-out any worry about damaging live stations

Coolant and chips sneak in.

Stop coolant and chips from damaging live tool stations.

NEW Shifted Toolholders

NEW DS SleeveHolders ➡ J26・J28・J31

Sleeves ➡ J129

For Swiss-type Lathes

[ N

ew Produ

cts ]

J12

New Products

NEW SATURN DUO

NEW Small Diameter Indexable End Mills

●High precision machining is made possible because of a low tool pressure chipbreakers

●New TM4 grade with improved wear and adhension resistance with longer tool life

Features

●FGV type for face grooving and FBV type for face machining●Economical double-corner specification●Improved tool rigidity by optimizing the overhang and holder shape

●Selection includes : gang-type, front-gang-type and sleeve holder type

Features

Holder : L-hand Insert : L-hand

Holder : R-hand Insert : R-hand

Shape ofgrooved face

FGV type for face groovingTarget work shape

・Grooving possible under a wide range of cutting conditions due to strengthened rigidity of both inserts and holders・Minimum machining diameter from φ.236", groove width from .039"・Left-hand types available for machining works with a boss

Holder : R-hand Insert : R-hand

Concavedface shape

FBV type for face machiningTarget work shape

・Further improved face machining efficiency・Minimum machining diameter from φ.315"

Inserts ➡ J76Holders ➡ J77Information ➡ J74

Inserts ➡ J115Holders ➡ J115Information ➡ J114

For Swiss-type Lathes

[ N

ew Produ

cts ]

J13

Tooling for Swiss-type Lathes

●Tooling ………………………………J14●NTK PVD Coatings ………………J15● Recommended Insert Grade and Cutting Conditions …………J16

J

For Swiss-type Lathes

[ Too

ling ]

J14

Tooling

Cut-off BackTurning Grooving Front

Turning Threading

Guide bushing

Tooling for gang type tool post

Tool post Tool

Guide bushingWork material

Threading

Front turning

Back turning

Cut-off

Grooving

➡J51 ➡J39 ➡J63 ➡J21 ➡J79

Tooling and Coatings

Tooling example for a small CNC automatic lathe (gang type)

Tooling example for a small CNC automatic lathe (turret type)

Cut-off Back Turning

Back Turning

Front Turning

Grooving

Tooling for turret type tool post

Cut-off

Cut-off

Guide bushing

Work material

Back Turning

Front Turning

Back Turn

ing

Back Turn

ing

Grooving

Grooving

➡J39 ➡J63

➡J21➡J39➡J51

[ Too

ling ]

For Swiss-type Lathes

J15

PVD Coatings

Best balance of wear resistance and adhesion resistance● For small part machining in general

TM4 TM-Coat

Best balance of heat resistance and sharp edges●Titanium alloy●Heat resistant alloy●Stainless steel●Hardened material

DT4 DT-Coat

Best wear resistance●stainless steel●Carbon steel●Alloy steel

QM3/Q15 Q-Coat

Best edge sharpness●Titanium alloy●Non-ferrous material●Stainless steel●Plastic

VM1 V-Coat

Best heat resistance● Heat resistant alloy● Stainless steel● Hardened material

DM4 DM-Coat

Best adhesion resistance● General purpose machining

ZM3/C7Z Z-Coat

Coating Specifications

Q-Coat TM-Coat DM-Coat DT-Coat V-Coat Z-Coat

Thickness Thick Thin Thick Thin Thin Thick

Wear Resistance ◎ ○ ○ ○ ○

Heat Resistance ◎ ◎ ○

Adhesion Resistance ○ ◎

Edge Sharpness ○ ○ ◎

Composition TiCN Multilayer Multilayer Multilayer TiCN TiN◎1st choice  ○2nd choice

NEW

NEWNEW

➡D30・D37

➡D36

➡D37

➡D36

➡D36

➡D31・D37

[ Too

ling ]

For Swiss-type Lathes

[ Coa

tings ]

J16

ToolingRecommended Insert Grade and Cutting Conditions■ Front TurningCSVF / CC.. / DC.. / VC.. / VB.. / TN.. / TF

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice DT4 DT4 TM4 QM32nd choice TM4 / QM3 QM3 / VM1 QM3 TM4 / DT4 / C7Z(X)

Cutting Speed (SFM) 75 125 225 100 200 275 130 230 330 150 300 600 Carbide 150 300 500C7Z(X) 400 500 800

RecommendedChipbreakerFeed Rate (IPR)

.004 DOC AMX KHG.0004 .0008 .0012

AMX KHG.0004 .0012 .0016

.004 to .060 DOC

CL S AM3.0008 .0016 .0024

CL AM3 AZ7 ZR S U/U1 UL.0008 .0020 .0032

.060 DOC CL S AM3.0008 .0015 .0025

CL AM3 ZP.0012 .0024 .0040

■ Back TurningCSVB

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice DT4 VM12nd choice VM1 DT4

Cutting Speed (SFM) 75 125 225 100 200 275 100 200 300

Feed Rate (IPR)X Direction .0004 .0008 .0012Z Direction .0004 .0012 .0016

TBDP / TBMH / TBP / TBPA / TBVC

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice DT4 DT4 / QM3 TM4 QM32nd choice TM4 / QM3 VM1 QM3 TM4 / DT4 / C7Z(X)

Cutting Speed (SFM) 75 125 225 100 200 275 150 300 500

Feed Rate (IPR)X Direction .0004 .0008 .0012 .0004 .0008 .0016Z Direction .0008 .0016 .0024 .0008 .0016 .0031

TB32 / TB43

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice

ZM3ZM3

2nd choice Z15

Cutting Speed (SFM) 50 100 150 ZM3 150 300 425Z15 400 600 800

Feed Rate (IPR)X Direction .0004 .0012 .0020 .0004 .0012 .0020Z Direction .0016 .0020 .0031 .0016 .0031 .0059

[ Too

ling ]

For Swiss-type Lathes

[ Rec

ommen

ded cu

tting co

ndition

s ]

J17

■ Cut OffCSVT

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice DT4 VM1

2nd choice VM1 DT4

Cutting Speed (SFM) 100 160 230 100 200 300

Feed Rate (IPR) .0004 .0008 .0012 .0004 .0012 .0020

CTP / CTPA / CTPS / CTPW

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice DT4 TM4 QM3

2nd choice TM4 QM3 / VM1 QM3 TM4 / DT4 / C7Z(X)

Cutting Speed (SFM) 100 160 230 100 200 300

Feed Rate (IPR) .0008 .0012 .0020 .0008 .0016 .0024

CTDP / CTV

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice DM4 TM4 QM3

2nd choice TM4 / QM3 QM3 TM4 / DM4

Cutting Speed (SFM) 100 160 230 100 200 300

Feed Rate (IPR) .0012 .0020 .0031 .0016 .0031 .0047 [ Too

ling ]

For Swiss-type Lathes

[ Rec

ommen

ded cu

tting co

ndition

s ]

J18

Tooling■ GroovingCSV / GTG / GTMH / GTMT / GTMX / SBG

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice DT4 DM4 / DT4 TM4 QM3

2nd choice TM4 / QM3 QM3 / VM1 QM3 TM4 / DT4 / C7Z(X)

Cutting Speed (SFM) 75 125 225 100 200 275 130 230 330 150 300 600 Carbide 150 300 500C7Z(X) 400 500 800

Feed Rate (IPR)

A. GroovingB. Side turning*

Width.010-.020

A. .0002 - .0012

B. .0001 - .0002

.020-.040A. .0008 - .0024 A. .0008 - .0028

B. .0002 - .0004 B. .0002 - .0004

.040-.080A. .0012 - .0028 A. .0012 - .0031

B. .0008 - .0020 B. .0012 - .0024

> .080A. .0012 - .0079

B. .0012 - .0024

*When side turining, Max. DOC is under .0079". Under .016" width side turning impossible

GVW

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice

QM32nd choice

Cutting Speed (SFM) 75 125 225 100 200 275 130 230 330 150 300 600 150 300 500

Feed Rate (IPR)

A. GroovingB. Side turning*

Width.118-.157 A. .0020 - .0059

.157-.197 A. .0039 - .0079A. .0039 - .0098

B. .0059 - .0118

> .197 A. .0059 - .0138

*Max DOC is 80% of width

GTPA

Work Material Aluminum Alloy

Common Name ASTM 5056ASTM 6061

Grade1st choice PD1

2nd choice KM1

Cutting Speed (SFM) PD1 330 650 1000KM1 160 330 650

Feed Rate (IPR)A. GroovingB. Side turning

A. .0020 - .0079

B. .0039 - .0079

Recommended Insert Grade and Cutting Conditions[ Too

ling ]

For Swiss-type Lathes

[ Rec

ommen

ded cu

tting co

ndition

s ]

J19

■ ThreadingWork Material High Temperature

AlloysTitanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice VM1 VM1 / ZM3 QM3

2nd choice ZM3 QM3 VM1 / ZM3

Cutting Speed (SFM) 75 125 225 100 200 275 130 230 330 150 300 600 150 300 500

*Unless your machine is equipped with high speed threading program, please set the feed rate to 80 IPM or lower to prevent making incomplete threads

■ ID Boringdiameter .240" (LBM / STICK DUO)

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice TM4 VM1 / TM4

2nd choice VM1 / ZM3 ZM3

Cutting Speed (SFM) 60 160 230 100 200 300

Feed Rate (IPR) .0004 .0012 .0020

Depth Of Cut (DOC) .0020 .0031 .0039

diameter > .240"

Work Material High Temperature Alloys

Titanium Alloys

Cobalt Chrome Alloys

Stainless SteelsAlloy Steels Carbon Steels

Hard to cut Free cutting

Common NameInconelHastelloyMP35N

Ti-6Al-4V ASTM F-7530431617-4PH

303430F

51204137

10451046

Grade1st choice DT4 DT4 TM4 QM3

2nd choice TM4 QM3 / TM4 QM3 TM4 / DT4 / C7Z(X)

Cutting Speed (SFM) 150 230 330 130 230 330 150 300 600 Carbide 150 300 500C7Z(X) 400 500 800

Feed Rate (IPR) .0008 .0024 .0047

Depth Of Cut (DOC) .0039 .0197 .0787

[ Too

ling ]

For Swiss-type Lathes

[ Rec

ommen

ded cu

tting co

ndition

s ]

MEMO

J21

General Turning / Front Turning

●General (ANSI / ISO) Turning ……J22●Front Turning ………………………J26

J

For Swiss-type Lathes

[ Front Turning

J22

General / Front Turning

●Advantage for each geometry

CC.. Style DC.. Style VC.. Style

Increased toughness. Cutting edge is close to insert pocket.

Versatile geometry. Toughness of CC.. with flexibility of VC..

Wide coverage in work geometry.

●For Undercuts

30° 45°

CC.. Style DC.. Style VC.. Style

Not applicable to undercut Up to 30 deg. undercuts Up to 45 deg. undercuts

●Chip Control and Finish

SCLCR ➡J26 SDJCR ➡J28 SDNCN ➡J28

Strong clamping.High dimensional repeatability.

Increased room for chip evacuation.Prevent chips from scratching works.

Chips flow away from the work.

■ General Turning Inserts Explained

[ Front Turning

]For Swiss-type Lathes

J23

■ Surface Finish in General Turning by Inserts with Wiper Flat

■ Roughing and Finishing Long Work on Swiss Lathes●Shifted Holders

w

●Combination of Grooving Tool and DS Holders

Guide bushing

Inserts with wiper

Slower feed rate brings better finish but sacrifices cycle time, chip control, and tool life

Fast feed rate improves chip control but worsens surface finish

Inserts with wiper flat bring good chip control and surface finish

SCLC-N-F ➡J26

SDJC-N-F ➡J28

SVJC-N-F ➡J31

Rough with grooving tool for good chip control

Shifted Holders make finishing process possible without worrying about bar stock coming off guide bushing.Thanks to the increased room between the tools and guide bushing, coolant flows effectively to improve chip control.

Finishing can be done by using general turning inserts with DS Holders

GTVW Holders ➡J71 DS Holders ➡J123

TFD ➡J28

for SDJC toolholders

TFT ➡J33

for STAC toolholders

TFV ➡J31

for SVAC toolholders

Wiper Flat Insert - Product Lines

[ Front Turning

]For Swiss-type Lathes

J24

General / Front Turning

ANSI / ISO Insert Nomenclature1 Shape

C 80°

D 55°

E 75°

L

P

R

S

T

V 35°

W 80°

2 Clearances 4 Type

11°

15°

20°

N

B

C

P

D

E

CInch C G T1 2 3 4

CMetric C G T

S TC

D K

φd

m m

φd s

3 Tolerance Class

Symbol d (inch) m (inch) s (inch)

M tolerance

M tolerance

Inscribed Circle

Inscribed Circle

d (inch)

d (inch)

1/43/81/25/83/41

±.002±.002±.003±.004±.004±.005

m (inch)

m (inch)

±.003±.003±.005±.006±.006±.007

AFCHEGJKLMNU

±.0010±.0050±.0010±.0050±.0010±.0010±.0020

±.002~ ±.005±.002~ ±.005±.002~ ±.005±.002~ ±.005±.003~ ±.010

±.0002±.0002±.0005±.0005±.0010±.0010±.0020±.0005±.0010

±.003~ ±.007±.003~ ±.007±.005~ ±.015

±.0010±.0010±.0010±.0010±.0010±.0050±.0050±.0010±.0010±.0050±.0010±.0050

1/43/81/25/83/4

±.002±.002±.003±.004±.004

±.004±.004±.006±.006±.007

6 Thickness

ThicknessS(inch)

3/32

1/8

5/32

3/16

1/4

5/16

3/8

1/2

Inch Metric

02

03

T3

04

06

07

09

12

1.5

2

2.5

3

4

5

6

8Special design

70°-90°

70°-90°

40°-60°

40°-60°

Type Symbol Type Symbol

N (E)

F

R

A

G

M

X

H

B

T

W

[ Front Turning

]For Swiss-type Lathes

J25

8 Edge Sharpness

3 2.5 08M F N AM35 6 7 8 9 10

09 T3 02M F N AM3

9 Hand of Chipbreaker 10 Type of Chipbreaker

C D R S T V WInscribedCircle

1/4

3/8

1/2

5/8

3/4

1

MetricInch

06

09

12

16

19

25

07

11

15

19

23

31

06

09

12

15

19

25

11

16

22

27

33

44

11

16

22

27

33

44

04

06

08

10

13

17

2

3

4

5

6

8

5 Cutting Edge Length

R

7 Nose RadiusCorner Radius Inch Metric

.001

.003

.004

.007

.008

.015

.016 (1/64)

.031 (1/32)

01

04M

04

08M

08

1M

1

2

00

01M

01

02M

02

04M

04

08

N Neutral*

R Right-hand

L Left-hand

* Omitted when edge is not "up-sharp".

See page C8 to C13 for chipbreaker information.

F Up-sharp edge (without any edge preparation)

(Blank) Non up-sharp edge

[ Front Turning

]For Swiss-type Lathes

J26

General / Front Turning

●Stock  ○1-2 week delivery

Toolholders for CC.. Inserts

■SCLC

■SCLC-F

5°4.724(120)

A A

95°

95°

5°4.724 (120)

Right-Hand style shown

Right-Hand style shown

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CC..21.5.. SCLC -062C ● ● 3/8 3/8 3/8 0 0 LRIS-2.5 × 7 CLR-15SSCLC -082C ● ● 1/2 1/2 1/2 0 0 LRIS-2.5 × 7 CLR-15S

CC..32.5.. SCLC -083C ● ● 1/2 1/2 1/2 0 0 LRIS-4 × 10 LLR-25SSCLC -103C ● ● 5/8 5/8 5/8 0 0 LRIS-4 × 10 LLR-25S

CC..21.5.. SCLC 0808X06N ● ○ .315 8 .315 8 .315 8 0 0 LRIS-2.5 × 7 CLR-15SCC..32.5.. SCLC 1212X09N ○ ○ .472 12 .472 12 .472 12 0 0 LRIS-4 × 10 LLR-25S

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CC..32.5..

SCLC 083C-F250 ● 1/2 .984 25 1/2 1/4 LRIS-4 × 10 LLR-25SSCLC 083C-F500 ● 1/2 .984 25 1/2 1/2 LRIS-4 × 10 LLR-25SSCLC 1015X09N-F05 ○ ○ .394 10 .591 15 .394 10 .197 5 LRIS-4 × 10 LLR-25SSCLC 1020X09N-F10 ○ ○ .394 10 .787 20 .394 10 .394 10 LRIS-4 × 10 LLR-25SSCLC 1218X09N-F06 ○ ○ .472 12 .709 18 .472 12 .236 6 LRIS-4 × 10 LLR-25SSCLC 1224X09N-F12 ○ ○ .472 12 .945 24 .472 12 .472 12 LRIS-4 × 10 LLR-25S

CC..

➡E27・E28・E29 / E22

[ Front Turning

]For Swiss-type Lathes

J27

■DS-SCLL-ACH

95°

φ

Left-Hand style shown

Left-Hand style shown

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CC..32.5..

DS-SCLL16F-09-ACH ● .630 16.00 .610 15.5 3.150 80 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL19-09-ACH ● 3/4 .709 18.0 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL20-09-ACH ● .787 20.00 .748 19.0 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL22-09-ACH ● .866 22.00 .827 21.0 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL25-09-ACH ● 1 .945 24.0 5.906 150 .236 6.0 LRIS-4 × 8 LLR-25S

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CC..21.5..

DS-SCLL15H-06 ○ 5/8 .591 15 3.937 100 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL16F-06 ○ .630 16 .591 15 3.150 80 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL19-06 ● 3/4 .709 18 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL20X-06 ○ .787 20 .748 19 3.740 95 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL20-06 ● .787 20 .748 19 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL22-06 ● .866 22 .827 21 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL25-06 ● 1 .945 24 5.906 150 .236 6.0 LRIS-2.5 × 7 CLR-15S

CC..32.5..

DS-SCLL15H-09 ○ 5/8 .591 15 3.937 100 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL16F-09 ○ .630 16 .591 15 3.150 80 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL19-09 ● 3/4 .709 18 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL19-09-004* ● 3/4 .709 18 4.724 120 .413 10.5 LRIS-4 × 8 LLR-25SDS-SCLL20X-09 ○ .787 20 .748 19 3.740 95 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL20-09 ● .787 20 .748 19 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL22-09 ● .866 22 .827 21 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL22-09-005* ● .866 22 .827 21 4.724 120 .472 12.0 LRIS-4 × 8 LLR-25SDS-SCLL25-09 ● 1 .945 24 5.906 150 .236 6.0 LRIS-4 × 8 LLR-25S

*Comes with coolant through

■DS-SCLL

0.0

A A

95°

.787

φ

(20)

0.0

AA

95°5°

1/8NPT

φ

Note: Use right-hand or neutral inserts for DS-SCLL bars

DS-SCLL19-09-004DS-SCLL22-09-005(Coolant through)

Adjustable centerline height

[ Front Turning

]For Swiss-type Lathes

J28

General / Front Turning

■SDJC ■SDJC-F

■SDNCN

A A93°

32°

4.724 (120)

32°

12

93°

4.724 (120)

62°30′

Right-Hand style shown Right-Hand style shown

Toolholders for DC.. / TFD InsertsDC..

➡E32・E33・E34 / E23

Item NumberIC Radius Thickness Grade

TFD (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) QM3 ZM3

With wiper

TFD 07FR05 1/4 6.35 .002 0.05 3/32 2.38 ● ○TFD 07FR15 1/4 6.35 .006 0.15 3/32 2.38 ● ○TFD 11FR05 3/8 9.525 .002 0.05 5/32 3.97 ● ○TFD 11FR15 3/8 9.525 .006 0.15 5/32 3.97 ● ○

NTK TFD-type is an insert with a wiper facet.It has a 0.3㎜ (.012")flat at cutting edge when set on the toolholder.The flat at cutting edge ensures superior surface finish at increased feed rate.Note: TFD type can be set on toolholders of SDJC-N,    SDJC-N-F, SDJC, CH-SDUC, Y-SDJC and Y-SDJC-OH.

.012(0.3㎜)

Nose Radius

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

DC..21.5..TFD07..

SDJC -062C ● ● 3/8 3/8 3/8 0 0 LRIS-2.5 × 7 CLR-15SSDJC -082C ● ● 1/2 1/2 1/2 0 0 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11..

SDJC -083C ● ● 1/2 1/2 1/2 0 0 LRIS-4 × 10 LLR-25SSDJC -103C ● ● 5/8 5/8 5/8 0 0 LRIS-4 × 10 LLR-25S

DC..21.5..TFD07.. SDJC 0808X07N ● ○ .315 8 .315 8 .315 8 0 0 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11..

SDJC 1212X11N ○ ○ .472 12 .472 12 .472 12 0 0 LRIS-4 × 10 LLR-25SSDJC 1616X11N ○ ○ .630 16 .630 16 .630 16 0 0 LRIS-4 × 10 LLR-25S

DC..32.5..TFD11..

SDJC 083C-F250 ● 1/2 .728 18.5 1/2 1/4 LRIS-4 × 10 LLR-25SSDJC 083C-F500 ● 1/2 1 1/2 1/2 LRIS-4 × 10 LLR-25S

DC..21.5..TFD07..

SDJC 1015X07N-F05 ○ ○ .394 10 .591 15 .394 10 .197 5 LRIS-2.5 × 7 CLR-15SSDJC 1020X07N-F10 ○ ○ .394 10 .787 20 .394 10 .394 10 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11..

SDJC 1015X11N-F05 ○ ○ .394 10 .591 15 .394 10 .197 5 LRIS-4 × 10 LLR-25SSDJC 1020X11N-F10 ○ ○ .394 10 .787 20 .394 10 .394 10 LRIS-4 × 10 LLR-25SSDJC 1218X11N-F06 ○ ○ .472 12 .709 18 .472 12 .236 6 LRIS-4 × 10 LLR-25SSDJC 1224X11N-F12 ○ ○ .472 12 .945 24 .472 12 .472 12 LRIS-4 × 10 LLR-25S

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

DC..21.5.. SDNCN-062 ● 3/8 3/8 2.5 63.5 3/8 3/16 LRIS-2.5 × 7 CLR-15SSDNCN-082 ● 1/2 1/2 3.5 88.9 1/2 1/4 LRIS-2.5 × 7 CLR-15S

DC..32.5.. SDNCN-083 ● 1/2 1/2 3.937 100 1/2 1/4 LRIS-4 × 10 LLR-25SSDNCN-103 ● 5/8 5/8 3.937 100 5/8 5/16 LRIS-4 × 10 LLR-25S

DC..21.5.. SDNCN08-X07 ○ .315 8 .315 8 4.724 120 .315 8 .157 4.0 LRIS-2.5 × 7 CLR-15SDC..32.5.. SDNCN12-X11 ○ .472 12 .472 12 4.724 120 .472 12 .236 6.0 LRIS-4 × 10 LLR-25S

●Stock  ○1-2 week delivery

[ Front Turning

]For Swiss-type Lathes

J29

Y-Axis Holders for DC.. / TFD Inserts■Y-SDJCR

■Y-SDNCN

.787(20)

93°

A

A

4.724 (120)

A A

90°62°30′

0.0

.827(21)

4.724(120)

Gang toolingpost

Feed direction

Feed direction

Gang toolingpost

Note: Y-SDJC holders do not work with left-hand inserts (such as DCGT-LS)

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

DC..21.5..TFD07..

Y-SDJCR062-IN ● 3/8 3/8 .984 25 0 LRIS-2.5 × 7 CLR-15SY-SDJCR082-IN ● 1/2 1/2 .984 25 0 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11..

Y-SDJCR083-IN ● 1/2 1/2 .984 25 0 LRIS-4 × 10 LLR-25SY-SDJCR103-IN ● 5/8 5/8 .984 25 0 LRIS-4 × 10 LLR-25S

DC..21.5..TFD07.. Y-SDJCR12-07L ○ .472 12 .472 12 1.181 30 0 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11.. Y-SDJCR12-11L ● .472 12 .630 16 1.181 30 0 LRIS-4 × 10 LLR-25S

DC..32.5..TFD11..

Y-SDJCR12-11SOH* ○ .472 12 .472 12 .787 20 ― LRIS-4 × 10 LLR-25SY-SDJCR16-11OH* ○ .630 16 .630 16 .984 25 ― LRIS-4 × 10 LLR-25S

*Comes with coolant through

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

DC..32.5.. Y-SDNCN083-IN ● 1/2 1/2 1/4 6.35 .984 25 LRIS-4 × 10 LLR-25S

DC..32.5..Y-SDNCN12-11S ○ .472 12 .472 12 .236 6.0 .787 20 LRIS-4 × 10 LLR-25S

Y-SDNCN16-11L ○ .630 16 .630 16 .315 8.0 1.181 30 LRIS-4 × 10 LLR-25S

93°

A A

0.0 4.724 (120)

■Y-SDJCR-OHCoolant-through for high-pressure coolant

[ Front Turning

]For Swiss-type Lathes

J30

General / Front Turning

DS Toolholders for DC.. / TFD Inserts■DS-SDUL

A A

0.0

122°

φ

■DS-SDUL-ACH

Ajustable range

0 - +.008

Ajustable range

0 - +.008

1.181(30)

φ

3°122°

■DS-SDXL22-11-006 (Coolant through)

1/8NPT

0.0

A A

119°

φ.787(20)

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

DC..21.5..TFD07..

DS-SDUL14F-07 ○ .551 14 .512 13 3.150 80 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL15H-07 ○ 5/8 .591 15 3.937 100 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL16F-07 ○ .630 16 .591 15 3.150 80 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL19-07 ● 3/4 .709 18 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL20-07 ● .787 20 .748 19 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL20X-07 ○ .787 20 .748 19 3.740 95 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL22-07 ● .866 22 .827 21 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11..*

DS-SDUL16F-11-ACH ● .630 16 .610 15.5 3.150 80 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL19-11 ● 3/4 .709 18.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL19-11-ACH ● 3/4 .709 18.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL20-11 ● .787 20 .748 19.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL20X-11 ○ .787 20 .748 19.0 3.740 95 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL20-11-ACH ● .787 20 .748 19.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL22-11 ● .866 22 .827 21.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL22-11-ACH ● .866 22 .827 21.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDXL22-11-006* ● .866 22 .827 21.0 4.724 120 .472 12.0 LRIS-4 × 10 LLR-25SDS-SDUL25-11 ● 1 .945 24.0 5.906 150 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL25-11-ACH ● 1 .945 24.0 5.906 150 .394 10.0 LRIS-4 × 10 LLR-25S

* TFD11 inserts cannnot be used with DS-SDXL toolholders

Left-Hand style shown

Left-Hand style shown

Left-Hand style shown

●Stock  ○1-2 week delivery

Adjustable centerline height

[ Front Turning

]For Swiss-type Lathes

J31

Toolholders for VC.. / TFV Inserts

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

VC..22

SVJC -062C ● ● 3/8 3/8 3/8 - - LRIS-2.5 × 7 CLR-15SSVJC -082C ● ● 1/2 1/2 1/2 - - LRIS-2.5 × 7 CLR-15SSVJC -102C ● ● 5/8 5/8 5/8 - - LRIS-2.5 × 7 CLR-15SSVJC -082C-F250 ● 1/2 1/2 .709 18 1/4 LRIS-2.5 × 7 CLR-15SSVJC -082C-F500 ● 1/2 1/2 .984 25 1/2 LRIS-2.5 × 7 CLR-15S

VC..22 SVJC 1212X11N ○ ○ .472 12 .472 12 .472 12 - - LRIS-2.5 × 7 CLR-15SSVJC 1616X11N ○ ○ .630 16 .630 16 .630 16 - - LRIS-2.5 × 7 CLR-15S

VC..22TFV11..

SVAC 0808X11N ● ● .315 8 .315 8 .315 8 - - LRIS-2.5 × 7 CLR-15SSVAC 1212X11N ○ ○ .472 12 .472 12 .472 12 - - LRIS-2.5 × 7 CLR-15S

VC..22 SVVCR1212X11N ○ .472 12 .472 12 .472 12 .197 5 LRIS-2.5 × 7 CLR-15SSVVCR1616X11N ○ .630 16 .630 16 .630 16 .197 5 LRIS-2.5 × 7 CLR-15S

VC..22..Y-SVJCR062-IN ● 3/8" 3/8" .787 .787 20 LRIS-2.5X7 CLR-15SY-SVJCR082-IN ● 1/2" 1/2" .787 .787 20 LRIS-2.5X7 CLR-15SY-SVJCR102-IN ● 5/8" 5/8" .787 .984 25 LRIS-2.5X7 CLR-15S

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

VC..22

DS-SVXL15H-11 ○ 5/8 .591 15 3.937 100 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL16F-11 ● .630 16 .591 15 3.150 80 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL19-11 ● 3/4 .709 18 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL20-11 ● .787 20 .748 19 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL20X-11 ○ .787 20 .748 19 3.740 95 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL22-11 ● .866 22 .827 21 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL25-11 ● 1 .945 24 5.906 150 .394 10 LRIS-2.5 × 7 CLR-15S

■SVJC ■SVJC-F

■Y-SVJCR

A A

52°

93°

4.274(120)

0.0

4.274(120)52°

93°

A A4.724(120)

0.0

.787(20)

93°

■SVAC-N

A A91°

54°

4.274(120)

0.0

■SVVCR-N

72°30′

4.724(120)

■DS-SVXL

A A

99°0.0

46°

φ

Item NumberIC Radius Thickness Grade

TFV (Inch) (Inch) (㎜) (Inch) (㎜) VM1 ZM3

with wiper

TFV 11FR05SX 1/4 .002 0.05 1/8 3.18 ● ○TFV 11FR05U 1/4 .002 0.05 1/8 3.18 ○ ○TFV 11FR10SX 1/4 .004 0.1 1/8 3.18 ● ○TFV 11FR10U 1/4 .004 0.1 1/8 3.18 ○ ○

Nose Radius

.008"(0.2㎜) NTK TFV-type is an insert with a wiper facet.

It has 0.2㎜ (.008")flat on cutting edge when set on the toolholder.The flat at cutting edge ensures superior surface finish at increased feed rate.Note: TFD type can be set on toolholders of SVAC-N

VC..

➡E49 / E26

Note: Use right-hand or neutral inserts for DS-SVXL bars

[ Front Turning

]For Swiss-type Lathes

J32

General / Front Turning

Toolholders for VP.. InsertsVP..

➡E50

■SVXP-N

A A

46°

99°

4.724(120)

0.0

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

VP..22..

SVXP 1012X11N ● ○ .394 10 .472 12 .394 10 LRIS-2.5 × 7 CLR-15S

SVXP 1212X11N ● ○ .472 12 .472 12 .472 12 LRIS-2.5 × 7 CLR-15S

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

VP..22..

DS-SVVPN16-11-ACH ● .630 16 .610 15.5 4.724 120 .591 15 LRIS-2.5 × 7 CLR-15SDS-SVVPN19-11 ○ 3/4 .709 18.0 4.724 120 LRIS-2.5 × 7 CLR-15SDS-SVVPN19-11-ACH ● 3/4 .709 18.0 4.724 120 .709 18 LRIS-2.5 × 7 CLR-15SDS-SVVPN20-11-ACH ● .787 20 .748 19.0 4.724 120 .748 19 LRIS-2.5 × 7 CLR-15SDS-SVVPN22-11 ○ .866 22 .827 21.0 4.724 120 LRIS-2.5 × 7 CLR-15SDS-SVVPN22-11-ACH ● .866 22 .827 21.0 4.724 120 .827 21 LRIS-2.5 × 7 CLR-15SDS-SVVPN25-11-ACH ● 1 .945 24.0 5.906 150 .945 24 LRIS-2.5 × 7 CLR-15S

■DS-SVVPN

35°

0.0

A A72°30’

1.063(27) φ

■DS-SVVP-ACH

Adjstable range

0 - .008

72°30'

1.378 (35)

φ

●Stock  ○1-2 week delivery

Right-Hand style shown

Adjustable centerline height

[ Front Turning

]For Swiss-type Lathes

J33

Toolholders for TC../ TFT InsertsTC..

➡E43

■STAC-N

91°

A A

4.724(120)

0.0

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TC..73..TFT09..

STAC 0808X09N ○ ○ .315 8 .315 8 .315 8 LRIS-2.2 × 6 CLR-13S

STAC 1010X09N ○ ○ .394 10 .394 10 .394 10 LRIS-2.2 × 6 CLR-13S

TC..21.5..TFT11.. STAC 1212X11N ○ ○ .472 12 .472 12 .472 12 LRIS-2.5 × 7 CLR-15S

Right-Hand style shown

Item NumberIC Radius Thickness ZM3

TFT (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L

S chipbreakerRight-hand style shown

TFT 09F 05 7/32 5.56 .002 0.05 3/32 2.38 ໐ ໐TFT 09F 15 7/32 5.56 .006 0.15 3/32 2.38 ໐ ໐TFT 11FR05 1/4 6.35 .002 0.05 3/32 2.38 ໐TFT 11FR15 1/4 6.35 .006 0.15 3/32 2.38 ໐

U/U1 chipbreakerRight-hand style shown

TFT 09FR05U 7/32 5.56 .002 0.05 3/32 2.38 ໐TFT 09FR15U 7/32 5.56 .006 0.15 3/32 2.38 ໐TFT 11FR05U1 1/4 6.35 .002 0.05 3/32 2.38 ໐TFT 11FR15U1 1/4 6.35 .006 0.15 3/32 2.38 ໐

NTK TFT-type is an insert with a wiper facet.It has 0.3㎜ (.118")flat on cutting edge when set on the toolholder.The flat at cutting edge ensures superior surface finish at increased feed rate.Note: TFT type can be set on toolholders of STAC-N

.012

(0.3)

30°

Cornerradius

[ Front Turning

]For Swiss-type Lathes

J34

General / Front Turning

Toolholders for TN.. InsertsTN..

➡E44・E45 / E25

(Inch, Metric)

Gage Insert Item number Stock Clamp pin Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TN..33..

PTXNR063C ● 3/8 5/8 3/8 .097 2.475 LCL33N LCS33 LW-2PTXNR083C ● 1/2 5/8 1/2 0 0 LCL33N LCS33 LW-2PTXNR103C ● 5/8 5/8 5/8 0 0 LCL33N LCS33 LW-2PTXNR1016X33N ○ .394 10 .630 16 .394 10 .079 2 LCL33N LCS33 LW-2PTXNR1216X33N ○ .472 12 .630 16 .472 12 0 0 LCL33N LCS33 LW-2PTXNR1616X33N ○ .630 16 .630 16 .630 16 0 0 LCL33N LCS33 LW-2PTXNR2020X33N ○ .787 20 .787 20 .787 20 0 0 LCL33N LCS33 LW-2

■PTXN-N - Pin lock type

.689(17.5)

(20)

.787

0.0

.709(18)

4.724(120)

AA6°

6° 100°

100°

Right-Hand style shown

1.496"b

R.004"

10°

0~+.008"

0~+.008"

Adjustable

range

6° φ

(Inch, Metric)

Gage Insert Item number Stock φ Clamp pin Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TN..33..

DS-PTXL16-33-ACH ● .630 16.00 .610 15.5 .591 15 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL19-33 ○ 3/4 .709 18.0 .709 18 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL19-33-ACH ● 3/4 .709 18.0 .709 18 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL20-33 ○ .787 20.00 .748 19.0 .748 19 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL20-33-ACH ● .787 20.00 .748 19.0 .748 19 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL22-33 ○ .866 22.00 .827 21.0 .827 21 4.724 120 .472 12 LCL33N LCS33 LW-2DS-PTXL22-33-ACH ● .866 22.00 .827 21.0 .827 21 4.724 120 .472 12 LCL33N LCS33 LW-2DS-PTXL25M-33 ○ 1 .945 24.0 .945 24 5.906 150 .512 13 LCL33N LCS33 LW-2DS-PTXL25-33-ACH ● 1 .945 24.0 .945 24 5.906 150 .512 13 LCL33N LCS33 LW-2

Right-Hand style shown

■DS-PTX

A A6°

10°

6°0.0

φ

●Stock  ○1-2 week delivery

■DS-PTX-ACH Adjustable centerline height

[ Front Turning

]For Swiss-type Lathes

J35

Toolholders for CN.. Inserts CN..

➡E30 / E22

(Inch, Metric)

Gage Insert Item number Stock Shim Clamppin

Clamp screw Spring Wrench

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CN..43.. PCLNR1620X43N ○ .630 16 .787 20 .630 16 LSC42 LCL4 LCS4CA LSP4 LW-3

See below for the explanation of the spare parts

■PCLN-Pin locktype

A A6° 95°

[ Front Turning

]For Swiss-type Lathes

J36

General / Front Turning

TFT Series■Inserts

Item numberGrade

(Inch) (㎜) ZM3TF3300R 0 0 ●TF3305R .002 0.05 ●TF3315R .006 0.15 ●TF3320R .008 0.2 ○

※Maximum depth of cut : .157" (4㎜)

.020 (0.5)

32°

3/16(4.76)

3/8(9.525)

6°.591(15)

4.724(120)

A A

Right-Hand style shown

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TF33..TFTR06-IN ● 3/8 3/8 3/8 0 0 .118 3 LR-S-4 × 10PW CLR-15STFTR08-IN ● 1/2 1/2 1/2 0 0 .039 1 LR-S-4 × 10PW CLR-15S

TF33..

TFTR10 ○ .394 10 .394 10 .394 10 0 0 .118 3 LR-S-4 × 10PW CLR-15STFTR12 ○ .472 12 .472 12 .472 12 0 0 .039 1 LR-S-4 × 10PW CLR-15STFTR16 ○ .630 16 .630 16 .630 16 0 0 0.0 0 LR-S-4 × 10PW CLR-15STFTR20 ○ .787 20 .787 20 .787 20 0 0 0.0 0 LR-S-4 × 10PW CLR-15S

Note: Max Depth of Cut is .157"(4.0㎜ )

■ToolholdersScrew accessible from both side

●:Stock ○: 1-2 week delivery M: Mirror finish

[ Front Turning

]For Swiss-type Lathes

J37

CSV Series - Inserts

Item number Chip-breaker

Max Depth of Cut Edge geometry(α×β°) DT4 VM1(Inch) (㎜) (Inch) (㎜) R L R L

CSVF11F V-M No ― ― .006 × 2° 0.15 × 2° ● ● ●CSVF11F VB Yes .118 3.00 .012 × 5° 0.30 × 5° ● ○CSVF11F VB-M Yes .118 3.00 .006 × 2° 0.15 × 2° ● ● ●

AA

.787(20)

4.724 (120)

0.0

1°

φ

■DS-CSVL (Takes right-hand inserts)

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11FR.. DS-CSVL15 ● 5/8 .591 15 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15S

CSV Series - Toolholders■CSV -NC

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..CSV 06-IN-NC ● ● 3/8 3/8 3/8 0 0 LRIS-2.5 × 7 CLR-15S

CSV 08-IN-NC ● ● 1/2 1/2 1/2 0 0 LRIS-2.5 × 7 CLR-15S

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..

CSV 07 ● ● .295 7 .295 7 .295 7 .020 0.5 LRIS-2.5 × 7 CLR-15SCSV 08 ● ● .315 8 .315 8 .315 8 0 0 LRIS-2.5 × 7 CLR-15SCSV 10 ● ● .394 10 .394 10 .394 10 0 0 LRIS-2.5 × 7 CLR-15SCSV 12 ● .472 12 .472 12 .472 12 0 0 LRIS-2.5 × 7 CLR-15S

■CSV

AA .7875.512 (140)(20)

.004

(0.1)

1°AA 1°

.7874.724 (120)(20)

.004

(0.1)

Right-Hand style shown Right-Hand style shown

Toolholders for right-hand inserts CSVR.., DS-CSVL..Toolholders for left-hand inserts CSVL..

Note: All angles shown are obtained when insert is set on the holder. All images in this page show right-hand inserts.

■CSVF - Front Turning

1/46.3

5

β°

30°

α

0.0

1/46.3

5

All CSV series inserts have mirror finish cutting edges

Left-Hand style shown

Mirror finish

M

M

M

[ Front Turning

]For Swiss-type Lathes

MEMO

J39

Back Turning

●Product Lines and Technical Information ……J40●Back Turning ………………………J42

J

For Swiss-type Lathes

[ Bac

k Tu

rning ]

J40

Back Turning

a: Length of Bladeb: Max Depth of Cut

ba

NTK Back Turning Tools - Product Lines

TBDP

➡J42a .138"b .197"TBDP..

BACK DUO

TBVC TB CSV

➡J47 ➡J48 ➡J43a .327" Max. a .138" Max. a .039" Max.b .327" b .197"/.354" b .087"TBVC.. TB.. CSVB..

TBMH (GTT Holder)

➡J49a .051" Max.b .106"TBMH..

Y-axis Holder available➡J70

DS-GTT

➡J70a .051" Max.b .106"TBMH..

TBP DS-TBP CTPA

➡J44 ➡J45 ➡J46a .189" Max. a .189" Max. a .169"b .208" b .209" b .205"TBP.. TBP..FR TBPA..

Y-axis Holder available➡J45

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J41

GradeWork material

PVD Coated CarbideZM3・QM3・VM1・DT4・TM4

CermetXT3

Steel 0.7 0.5Stainless Steel 0.6 0.4

Non-ferrous material 0.9 0.8Plastic 0.9 0.9

■When length of blade (a) is not long enough ■When having rough finish on shoulder

Back turning can be performed multiple times until the total depth of cut reaches b.

Turning shoulder twice can improve the finish.This Problem can be solved by using Back Duo without increasing the number of pass.

■Undercut

TBMH style inserts should be used to cut the undercut

Assume undercut exists on back turning section

■Finish cut

TBP TBVCR・・F10

Roughed section goes into the guidebushing when performing finish cuts.(Deburring may be needed upon roughing)

Cutting edge is located away from the guide bushing. Roughing can be performed without retracting roughed part to guide bushing.

➡J44 ➡J47

TBMH32 ➡J49GTTR ➡J49DS-GTTL ➡J70

■Recommend max depth of cut for each pass(Multiply this ratio by the length of blade (a) to obtain the max. depth of cut for each pass)

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J42

Back Turning

Gage Insert Item numberStock Clamp

screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBDP..

TBDPR06-IN ● 3/8 .472 12 3/8 .081 2.05 .571 14.5 .118 3.0 .079 2 LRIS-4 × 12 LLR-25STBDPR08-IN ● 1/2 1/2 1/2 .081 2.05 .689 17.5 .197 5.0 0 0 LRIS-4 × 12 LLR-25STBDPR10-IN ● 5/8 5/8 5/8 .081 2.05 .768 19.5 .197 5.0 0 0 LRIS-4 × 12 LLR-25STBDP 1012 ○ ○ .394 10 .472 12 .394 10 .081 2.05 .571 14.5 .118 3.0 .079 2 LRIS-4 × 12 LLR-25STBDP 12 ○ ○ .472 12 .472 12 .472 12 .081 2.05 .689 17.5 .197 5.0 0 0 LRIS-4 × 12 LLR-25STBDP 16 ○ ○ .630 16 .630 16 .630 16 .081 2.05 .768 19.5 .197 5.0 0 0 LRIS-4 × 12 LLR-25STBDP 20 ○ .787 20 .787 20 .787 20 .081 2.05 .768 19.5 .197 5.0 0 0 LRIS-4 × 12 LLR-25S

.055

(1.4)

13° .012

(0.3)

.087

(2.2)

Item numberEffective cuttingedge length

Dimensions (mm) Grade

θ TM4 QM3(Inch) (㎜) (Inch) (㎜)

TBDP22005R

.138 3.5 80

.002 0.05 ● ●

TBDP2201MR .003 0.08 ● ●

TBDP2202MR .007 0.18 ● ●

BACK DUOSee and feel the finish quality competitors' can't provide !

Back-turning tools occasionally bring problems that the surface facing against the back of the tool (shoulder) is roughened by chips. Our unique chipbreaker can solve the problems and provide exceptional surface finish in a single pass !At the same time, you can reduce the cycle time!

PAT.P

New 3D chipbreaker

.079

.039

.118

.002 .004

BACK DUO

Feed(IPR)

D.O

.C(

inch)

Chip control range

Right hand type shown

■Toolholders

■Inserts

Max depth of cut

Shift amount.081 (2.05)

4.724 (120)

●:Stock ○: 1-2 week delivery M: Mirror finish

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J43

CSV Series - Inserts All CSV series inserts have mirror finish cutting edges

Toolholders for right-hand inserts CSVR.., DS-CSVL..Toolholders for left-hand inserts CSVL..

Note: All angles shown are obtained when insert is set on the holderAll images in this page show right-hand inserts

■CSVB - Back Turning

Item number Chip- breaker

Edge geometry(α×β°) DT4 VM1(Inch) (㎜) (Inch) (㎜) R L R L

CSVB11F V-M No .039 1.00 .006 × 2° 0.15 × 2° ● ● ●CSVB11F VB-M Yes .039 1.00 .006 × 2° 0.15 × 2° ● ● ●

1/4

(6.35)

α

β°45°

0.00.98(2.5)

W±.002"

1/4

(6.35)

CSV Series - Toolholders

■DS-CSVL (Takes right-hand inserts)

■CSV -NC

AA 1°

.7874.724 (120)(20)

.004

(0.1)

AA

.787(20)

4.724 (120)

0.0

1°

φ

■CSV

AA .7875.512 (140)(20)

.004

(0.1)

1°

Right-Hand style shown

CSV -NC (Inch)

Gage Insert Item numberStock Clamp

screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..CSV 06-IN-NC ● ● 3/8 3/8 3/8 0 0 LRIS-2.5 × 7 CLR-15S

CSV 08-IN-NC ● ● 1/2 1/2 1/2 0 0 LRIS-2.5 × 7 CLR-15S

CSV (Metric, ㎜)

Gage Insert Item numberStock Clamp

screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..

CSV 07 ● ● .295 7 .295 7 .295 7 .020 0.5 LRIS-2.5 × 7 CLR-15SCSV 08 ● ● .315 8 .315 8 .315 8 0 0 LRIS-2.5 × 7 CLR-15SCSV 10 ● ● .394 10 .394 10 .394 10 0 0 LRIS-2.5 × 7 CLR-15SCSV 12 ● .472 12 .472 12 .472 12 0 0 LRIS-2.5 × 7 CLR-15S

DS-CSVL (Inch)

Gage Insert Item number Stockφ

Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11FR.. DS-CSVL15 ● 5/8 .591 15 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15S

Mirror finish

M

M

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J44

Back Turning

TBP Series - Inserts

TBP Series - Toolholders■TBP

.008(0.2)

. 028(0.7)

15°

〈FRV-P, PD1〉

Item number HolderType

Chip-breaker

QM3 ZM3 DT4 VM1 PD1(Inch) (㎜) (Inch) (㎜) R L R L R L R L R L

TBP55F 00

TBP ..Y-TBPR..DS-TBPL..

Yes55° 0.0 0 .110 2.8 ● ○ ○

TBP55F 10 55° .004 0.1 .110 2.8 ● ○ ○TBP60F 00

Yes60° 0.0 0 .138 3.5 ● ● ○ ● ●

TBP60F 10M 60° .003 0.08 .138 3.5 ● ● ●TBP60F 10 60° .004 0.1 .138 3.5 ● ● ○ ●TBP60F V

No60° 0.0 0 .189 4.8 ● ○ ○

TBP60F V05 60° .002 0.05 .189 4.8 ○TBP60F V10 60° .004 0.1 .189 4.8 ● ○TBP60F V00-P*

No60° 0.0 0 .157 4.0 ●

TBP60F V10-P* 60° .004 0.1 .157 4.0 ●* 1corner

.591(15)

4.724(120)

.217(5.5)

.138(3.5)

.787(20.0)

.315(8.0)

.098(2.5)

50°

15°.020(0.5)

15°.028(0.7)

.008

(0.2)

.208(5.3)

Lengthof blade

Max. depthof cut

With Chipbreaker Without Chipbreaker

θshows the angle when the holder is set

Right-Hand style shown

Right-Hand style shown

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBP..FR..

TBP 06-IN ● 3/8 3/8 3/8 .079 2 LRIS-4 × 10PW CLR-15STBP 08-IN ● 1/2 1/2 1/2 0 0 LRIS-4 × 12PW CLR-15STBP 10-IN ● 5/8 5/8 5/8 0 0 LRIS-4 × 12PW CLR-15STBP 08 ● ○ .310 8 .390 10 .310 8 .016 4 LRIS-4 × 10PW CLR-15STBP 12 ● ○ .470 12 .470 12 .470 12 0 0 LRIS-4 × 12PW CLR-15STBP 16 ○ ○ .700 16 .700 16 .700 16 0 0 LRIS-4 × 12PW CLR-15S

■TBPMax. Total Depth of Cut .208" (5.3㎜) (Caution: Each pass should not exceed L)

Screw Accessible from both side

〈FRV〉Mirror finish

MMM

●:Stock ○: 1-2 week delivery M: Mirror finish

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J45

■Y-TBPR

■Y-TBPR-OH

■DS-TBP

.138(3.5) 4.724(120)

0.0

.787(20)

Feed direcition

Gang tooling post

Right-Hand style shown

Note: Use right-hand inserts for Y-TBPR and Y-CTPAR holders

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBP..FR..

Y-TBPR06-IN ● 3/8 3/8 .984 25 LRIS-4 × 10PW CLR-15SY-TBPR08-IN ● 1/2 1/2 .984 25 LRIS-4 × 12PW CLR-15SY-TBPR10-IN ● 5/8 5/8 .984 25 LRIS-4 × 12PW CLR-15SY-TBPR12 ○ .472 12 .472 12 .984 25 LRIS-4 × 12PW CLR-15SY-TBPR12SOH ○ .472 12 .472 12 .787 20 LRIS-4 × 12PW CLR-15SY-TBPR16OH ○ .700 16 .700 16 .984 25 LRIS-4 × 12PW CLR-15S

(Inch, Metric)

Gage Insert Item number Stockφ

Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBP..FR..DS-TBPL19 ● 3/4 .709 18 4.724 120 .433 11 LRIS-4 × 10 LLR-25SDS-TBPL20 ○ .787 20 .748 19 4.724 120 .433 11 LRIS-4 × 10 LLR-25SDS-TBPL25 ● 1 .945 24 5.906 150 .512 13 LRIS-4 × 10 LLR-25S

0.0

.138(3.5)

.217(5.5)

.591(15) φ

Left-Hand style shown

Screw accessible from both side

Coolant-through for high-pressure coolantScrew accessible from both side

0.0

2.756 (70)

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J46

Back Turning

TBPA Series - Inserts

TBPA Series - Toolholders■CTPA

Item number HolderType

Chip-breaker

QM3 ZM3 DT4 VM1(Inch) (㎜) (Inch) (㎜) R L R L R L R L

TBPA60F VB

CTPA ..Y-CTPAR..

Yes 60° 0.0 0 .169 4.3 ● ○ ○ ●

TBPA60F 10M Yes 60° .003 0.08 .169 4.3 ●

TBPA60F PB10M Yes 60° .003 0.08 .169 4.3 ● ○

TBPA60F PB10 Yes 60° .004 0.1 .169 4.3 ● ○ ●

TBPA60F PB20M Yes 60° .007 0.18 .169 4.3 ●

A A.984(25.0)

.700(16)

1°

.295(7.5)

.134(3.4)

4.724(120)

.768(19.5)

.028(0.7)

.008

(0.2)

15°

60°

.205(5.2)

Max. depth of cut

With Chipbreaker

Lengthof blade

θshows the angle when the holder is set

Right-Hand style shown

Right-Hand style shown

(Inch, Metric)

Gage Insert Item numberStock /

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBPA..(Back turning)

CTPA..(Cut-off)

CTPA 06-IN ● ● 3/8 3/8 3/8 0 0 LRIS-4 × 10PW CLR-15SCTPA 08-IN ● ● 1/2 1/2 1/2 0 0 LRIS-4 × 12PW CLR-15SCTPA 10-IN ● ● 5/8 5/8 5/8 0 0 LRIS-4 × 12PW CLR-15SCTPA 12 ● ● .470 12 .470 12 .470 12 0 0 LRIS-4 × 12PW CLR-15SCTPA 16 ○ ○ .700 16 .700 16 .700 16 0 0 LRIS-4 × 12PW CLR-15S

TBPA.. Y-CTPA 08L-IN ● 1/2 1/2 1.181 30 ― ― LRIS-4 × 12PW CLR-15S

.014(3.5)

.984(25.0)

.370

(9.40)

45°

■TBPAMax. Total Depth of Cut .208" (5.3㎜) (Caution: Each pass should not exceed L)

Screw accessible from both side

■Y-CTPA

.134(3.4) 4.724 (120)

0.0

.984(25)

Screw accessible from both side

●:Stock ○: 1-2 week delivery M: Mirror finish

M

M

M

M

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J47

TBVC Series■Inserts

Right-Hand style shown

.020(0.5)

35° U

S

Item number HolderType

Grade(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) ZM3 VM1

TBVC11FR05UTBVCR..

1/4 6.35 1/8 3.18 .002 0.05 ●TBVC11FR10U 1/4 6.35 1/8 3.18 .004 0.10 ● ●TBVC11FR10S 1/4 6.35 1/8 3.18 .004 0.10 ●

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBVC11VCGT22..

TBVCR08-F10-IN ● 1/2 1/2 1/2 .394 10 LRIS-2.5 × 7 CLR-15STBVCR12-F10 ● .472 12 .472 12 .472 12 .394 10 LRIS-2.5 × 7 CLR-15STBVCR16-F10 ● .630 16 .630 16 .630 16 .394 10 LRIS-2.5 × 7 CLR-15S

Right-Hand style shown

■ToolholdersMax. Depth of Cut .335" (8.5㎜) Screw-on type, 35° Diamond positive type

Note: VCGT22.. inserts can be used with TBVCR holders

53°

.335"(8.5)

4.724 (120)

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J48

Back Turning

Gage Insert Item number

StockClamp Clamp

screw Spring WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TB43

TB 16N ● ○ .630 16 .630 16 .354 9 .630 16 3.071 78 CPR5S AOS-5×25 ASG-5 LW-2.5

TB 20N ○ ○ .787 20 .787 20 .197 5 .787 20 3.937 100 CPR5S AOS-5×25 ASG-5 LW-2.5

TB 25F* ○ ○ .984 25 .984 25 0 0 .984 25 5.906 150 CPR5 AOS-5×25 ASG-5 LW-2.5

■TB32, TB43 Inserts

■TBT ■TB-N

Item number Holder Type

ZM3 XT3(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L R L

TB3200

TBT ..

0.0 .098 2.5 .020 0.5 3/8 9.525 1/8 3.18 ●TB3205 .002 0.05 .098 2.5 .020 0.5 3/8 9.525 1/8 3.18 ● ○ ●TB3210 .004 0.10 .098 2.5 .020 0.5 3/8 9.525 1/8 3.18 ○TB3215 .006 0.15 .098 2.5 .020 0.5 3/8 9.525 1/8 3.18 ● ○ ● ○TB4300

TBR ..

0.0 .138 3.5 .040 1.0 1/2 12.7 3/16 4.76TB4305 .002 0.05 .138 3.5 .040 1.0 1/2 12.7 3/16 4.76 ● ●TB4315 .006 0.15 .138 3.5 .040 1.0 1/2 12.7 3/16 4.76 ● ● ●TB4340 .016 0.40 .138 3.5 .040 1.0 1/2 12.7 3/16 4.76 ● ● ○

(Inch, Metric)Gage Insert Item number

StockClamp screw Wrench

R L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TB32 TBT 06-IN ● 3/8 3/8 .118 3 3/8 4.724 120 LR-S-4 × 10PW CLR-15STBT 08-IN ● 1/2 1/2 .039 1 1/2 4.724 120 LR-S-4 × 10PW CLR-15S

TB32 TBT 08K ○ ○ .315 8 .315 8 .197 5 .315 8 4.724 120 LR-S-4 × 10PW CLR-15STBT 12K ○ ○ .472 12 .472 12 .039 1 .472 12 4.724 120 LR-S-4 × 10PW CLR-15S

Note: θ shows the angle when the insert is set on the holder

Right-Hand style shown

Screw accessible from both sides

.197(5)

.157 (4)

.591(15)

Max. depthof cut

.984(25)

.394(10)

.354 (9)

2°6°

Max. depthof cut

d s

45°

Length of blade

TB Series

Toolholders for TB32/43 Inserts

●Stock  ○1-2 week delivery

* with off-set

[ Bac

k Tu

rning ]

For Swiss-type Lathes

J49

1/8”(3.18)

Length of blade

Max. depth of cut

3/8”(9.525)

Note: Dimensions shown here are when the inserts is in the holder

See page J70 for Y-GTTR and DS-GTTL holders

Right-Hand style shown

Right-Hand style shown

Item number HolderType

ZM3(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R

TBMH32100R05-22GTTR..Y-GTTR..DS-GTTL..

.039 1.0 22° .002 0.05 .070 1.8 .012 0.3 ○TBMH32100R05-45 .039 1.0 45° .002 0.05 .070 1.8 .035 0.9 ○TBMH32150R05-22 .059 1.5 22° .002 0.05 .106 2.7 .020 0.5 ●TBMH32150R05-45 .059 1.5 45° .002 0.05 .102 2.6 .051 1.3 ●

A A

4.724(120)Max depth

.591(15)

0.0

(Inch)

Gage Insert Item Number

Stock Groove width range ( ) , ClampScrew Wrench

R L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TMG32..GTM..32..TBMH32..

GTT 06A-IN ● ● .012~.118 0.30~3.00 3/8 3/8 .079 2 .118 3 LR-S-4×10PW CLR-15SGTT 08A-IN ● ● .012~.118 0.30~3.00 1/2 1/2 .079 2 .039 1 LR-S-4×10PW CLR-15SGTT 10A-IN ● ● .012~.118 0.30~3.00 5/8 5/8 .079 2 0 0 LR-S-4×10PW CLR-15SGTT 12A-IN ● .012~.118 0.30~3.00 3/4 3/4 .079 2 0 0 LR-S-4×10PW CLR-15SGTT 06B-IN ● ● .057~.118 1.45~3.00 3/8 3/8 .118 3 .118 3 LR-S-4×10PW CLR-15SGTT 08B-IN ● ● .057~.118 1.45~3.00 1/2 1/2 .118 3 .039 1 LR-S-4×10PW CLR-15SGTT 10B-IN ● ● .057~.118 1.45~3.00 5/8 5/8 .118 3 0 0 LR-S-4×10PW CLR-15SGTT 12B-IN ● .057~.118 1.45~3.00 3/4 3/4 .118 3 0 0 LR-S-4×10PW CLR-15S

Note: Modification is required to groove deeper than L1

(Metric, mm)

Gage Insert Item Number

Stock Groove width range ( ) , ClampScrew Wrench

R L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TMG32..GTM..32..TBMH32..

GTT 08K00 ● ○ .012~.118 0.30~3.00 .315 8 .315 8 .079 2 .197 5 LR-S-4×10PW CLR-15SGTT 10K00 ○ ○ .012~.118 0.30~3.00 .394 10 .394 10 .079 2 .118 3 LR-S-4×10PW CLR-15SGTT 12K00 ● ○ .012~.118 0.30~3.00 .472 12 .472 12 .079 2 .039 1 LR-S-4×10PW CLR-15SGTT 16K00 ● ○ .012~.118 0.30~3.00 .630 16 .630 16 .079 2 0 0 LR-S-4×10PW CLR-15SGTT 10K15 ○ ○ .057~.118 1.45~3.00 .394 10 .394 10 .118 3 .118 3 LR-S-4×10PW CLR-15SGTT 12K15 ○ ○ .057~.118 1.45~3.00 .472 12 .472 12 .118 3 .039 1 LR-S-4×10PW CLR-15SGTT 16K15 ● ○ .057~.118 1.45~3.00 .630 16 .630 16 .118 3 0 0 LR-S-4×10PW CLR-15SGTT 10K25 ○ ○ .098~.118 2.50~3.00 .394 10 .394 10 .118 3 .118 3 LR-S-4×10PW CLR-15SGTT 12K25 ○ ○ .098~.118 2.50~3.00 .472 12 .472 12 .118 3 .039 1 LR-S-4×10PW CLR-15SGTT 16K25 ○ ○ .098~.118 2.50~3.00 .630 16 .630 16 .118 3 0 0 LR-S-4×10PW CLR-15S

■TBMH32 For Back turning

GTT Toolholders for TBMH Inserts Screw accessible from both side Shank.315"(8㎜)~.630"(16㎜)Without Off-set

TBMH Inserts

[ Bac

k Tu

rning ]

For Swiss-type Lathes

MEMO

J51

Cut-off / Parting

●Product Lines ………………………J52●Cut-off ………………………………J54

J

For Swiss-type Lathes

[ Cut-off / Pa

rting ]

J52

Cut-off / Parting

CTP CTPA CTPS

➡J56 ➡J56 ➡J61Covered rangeMax. φ.472"

Covered rangeMax. φ.630"

Covered rangeMax. φ.394"

Blade width.020" to .079"

Blade width.028" to .079"

Blade width.047" to .079"

CTP.. CTPA.. CTPS..

NTK Cut-off Tools - Product Lines

NTK offers a variety of cut-off tools as narrow width as .020" (0.5mm)NTK cut-off tools are specialized to small part applications

For CTP, CTPA, and CTPS, SUB style holders are available, which have extra clearance for sub spindle

Sub-chuck

Guide Bushing•All inserts shown on this page are double-ended

•Even if a cutting edge broke, the other edge can be used without any limitations

CTPW

➡J56Covered rangeMax. φ.787"

Blade width .098"CTPW..

φ.787"

(20.0

㎜)

φ.197"

(5.0㎜)

φ.630"

(16 .0

㎜)

CSV CSV-NC

➡J60 ➡J60Covered rangeMax. φ.197"

Covered rangeMax. φ.197"

Blade width.024" to .051"

Blade width.024" to .051"

CSVC.. CSVC..

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J53

Cut-off Insert Edge ConfigurationFor Right Hand Toolholder For Left Hand Toolholder

FR, FRFT*FRV**

FRN, FRS*FRNV** FRK FL, FLV** FLN, FLS* FLK, FLKFT*

FLKV**

* FRFT, FRS, FLKFT and FLS have flat top (No chipbreakers)** FRV, FRNV, FLV and FLKV have flat top with mirror finish

CTV

➡J59Covered range Max. φ1.378"Blade width .098" to .118"

CTV..

φ1.378"

(35.0

㎜)

φ1.339"

(34 .0

㎜)

CTDP型

➡J58Covered range Max. φ1.339"Blade width .079" to .098"

CTDP..

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J54

Cut-off / Parting

■CTP / CTPA ■CTPW

CTP / CTPA / CTPW Inserts (Right-hand)

±.002"

50°

Insert Geometry (Inch)

CTP .787 .315 .098CTPA .984 .370 .138CTPW 1.772 .382 .256

±.002"

FR HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 KM1CTP 05 FR-SH CTPR.. .197 5 .020 0.5 15 .001 0.03 ●CTP 07 FR CTPR.. .315 8 .028 0.7 16 .002 0.05 ●CTP 10 FR CTPR.. .472 12 .039 1.0 16 .002 0.05 ● ● ●CTP 15 FR CTPR.. .472 12 .059 1.5 16 .002 0.05 ● ●CTPX 15 FR CTPR.. .472 12 .059 1.5 16 .002 0.05 ● ○ ●CTP 20 FR CTPR.. .472 12 .079 2.0 16 .002 0.05 ● ●CTPX 20 FR CTPR.. .472 12 .079 2.0 16 .002 0.05 ● ○ ●CTPA 07 FR CTPAR.. .315 8 .028 0.7 16 .002 0.05 ●CTPA 10 FR CTPAR.. .472 12 .039 1.0 16 .002 0.05 ● ● ●CTPA 15 FR CTPAR.. .630 16 .059 1.5 16 .002 0.05 ● ● ● ●CTPAX 15 FR CTPAR.. .630 16 .059 1.5 16 .002 0.05CTPA 20 FR CTPAR.. .630 16 .079 2.0 16 .002 0.05 ● ● ● ●CTPAX 20 FR CTPAR.. .630 16 .079 2.0 16 .002 0.05CTPW 25 FR CTPWR.. .787 20 .098 2.5 17 .002 0.05 ●

±.002"

FRFT, FRV HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 KM1CTP 10 FRV CTPR.. .472 12 .039 1.0 20 .000 0.00 ○ ● ● ○CTP 15 FRV CTPR.. .472 12 .059 1.5 20 .000 0.00 ● ● ○CTP 20 FRV CTPR.. .472 12 .079 2.0 20 .000 0.00 ● ● ○CTPA 10 FRFT CTPAR.. .472 12 .039 1.0 20 .002 0.05 ●CTPA 15 FRFT CTPAR.. .630 16 .059 1.5 20 .002 0.05 ●

=0°

±.002"

FRN-P(PCD tipped)

FRN, FRN-P HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 PD1CTP 05 FRN-SH CTPR.. .197 5 .020 0.5 0 .001 0.03 ●CTP 10 FRN CTPR.. .472 12 .039 1.0 0 .002 0.05 ● ●CTP 15 FRN CTPR.. .472 12 .059 1.5 0 .002 0.05 ● ●CTPX 15 FRN CTPR.. .472 12 .059 1.5 0 .002 0.05 ● ●CTP 20 FRN CTPR.. .472 12 .079 2.0 0 .002 0.05 ● ●CTPX 20 FRN CTPR.. .472 12 .079 2.0 0 .002 0.05 ● ●CTPA 07 FRN CTPAR.. .315 8 .028 0.7 0 .002 0.05 ●CTPA 10 FRN CTPAR.. .472 12 .039 1.0 0 .002 0.05 ● ● ●CTPA 15 FRN CTPAR.. .630 16 .059 1.5 0 .002 0.05 ● ● ● ●CTPAX 15 FRN CTPAR.. .630 16 .059 1.5 0 .002 0.05 CTPA 20 FRN CTPAR.. .630 16 .079 2.0 0 .002 0.05 ● ● ● ●CTPA 20 FRN-P CTPAR.. .630 16 .079 2.0 0 .004 0.10 ●CTPAX 20 FRN CTPAR.. .630 16 .079 2.0 0 .002 0.05 CTPW 25 FRN CTPWR.. .787 20 .098 2.5 0 .002 0.05 ●

=0°

±.002"

FRNV, FRS HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 KM1CTP 15 FRNV CTPR.. .472 12 .059 1.5 0 .000 0.00 ○CTP 20 FRNV CTPR.. .472 12 .079 2.0 0 .000 0.00 ○CTPA 10 FRS CTPAR.. .472 12 .039 1.0 0 .002 0.05 ●CTPA 15 FRS CTPAR.. .630 16 .059 1.5 0 .002 0.05 ●CTPA 20 FRS CTPAR.. .630 16 .079 2.0 0 .002 0.05 ●

Flat top

Flat top

●:Stock ○: 1-2 week delivery □: To be discontinued M: Mirror finish

MMM

MM

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J55

CTP / CTPA / CTPW Inserts (Left-hand)

±.002"

FLK HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 KM1CTP 05 FLK-SH CTPL.. .197 5 .020 0.5 17 .001 0.03 ●CTP 10 FLK CTPL.. .433 11 .039 1.0 16 .002 0.05 ● ● ●CTP 10 FLK-211 CTPL.. .472 12 .039 1.0 16 .002 0.05 ●CTP 15 FLK CTPL.. .433 11 .059 1.5 16 .002 0.05 ● ●CTPX 15 FLK CTPL.. .433 11 .059 1.5 16 .002 0.05 ● ●CTP 20 FLK CTPL.. .433 11 .079 2.0 16 .002 0.05 ● ○CTPX 20 FLK CTPL.. .433 11 .079 2.0 16 .002 0.05 ● ●CTPA 07 FLK CTPAL.. .256 6.5 .028 0.7 16 .002 0.05 ●CTPA 10 FLK CTPAL.. .433 11 .039 1.0 16 .002 0.05 ● ● ●CTPA 15 FLK CTPAL.. .571 14.5 .059 1.5 16 .002 0.05 ● ● ● ●CTPAX 15 FLK CTPAL.. .571 14.5 .059 1.5 16 .002 0.05 CTPA 20 FLK CTPAL.. .571 14.5 .079 2.0 16 .002 0.05 ● ● ● ●CTPAX 20 FLK CTPAL.. .571 14.5 .079 2.0 16 .002 0.05 CTPW 25 FLK CTPWL.. .787 20 .098 2.5 17 .002 0.05 ●

±.002"

FL HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 KM1CTP 07 FL CTPL.. .315 8 .028 0.7 16 .002 0.05 ●CTP 10 FL CTPL.. .472 12 .039 1.0 16 .002 0.05 ●CTP 15 FL CTPL.. .472 12 .059 1.5 16 .002 0.05 ○ ○CTP 20 FL CTPL.. .472 12 .079 2.0 16 .002 0.05 ○ ●CTPA 07 FL CTPAL.. .315 8 .028 0.7 16 .002 0.05 ○CTPA 10 FL CTPAL.. .472 12 .039 1.0 16 .002 0.05 ○ ○CTPA 15 FL CTPAL.. .630 16 .059 1.5 16 .002 0.05 ○ ○ ○CTPA 20 FL CTPAL.. .630 16 .079 2.0 16 .002 0.05 ○ ● ●CTPW 25 FL CTPWL.. .787 20 .098 2.5 17 .002 0.05 ○

±.002"

FRK HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 KM1CTP 10 FRK CTPR.. .433 11 .039 1.0 16 .002 0.05 ● □CTP 15 FRK CTPR.. .433 11 .059 1.5 16 .002 0.05 ●CTP 20 FRK CTPR.. .433 11 .079 2.0 16 .002 0.05 ●

=0°

±.002"

FLN-P(PCD tipped)

FLN HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 PD1CTP 05 FLN-SH CTPL.. .197 5 .020 0.5 0 .001 0.03 ●CTP 10 FLN CTPL.. .472 12 .039 1.0 0 .002 0.05 ● ●CTP 15 FLN CTPL.. .472 12 .059 1.5 0 .002 0.05 ● ●CTPX 15 FLN CTPL.. .472 12 .059 1.5 0 .002 0.05 ● ●CTP 20 FLN CTPL.. .472 12 .079 2.0 0 .002 0.05 ● ●CTPX 20 FLN CTPL.. .472 12 .079 2.0 0 .002 0.05 ● ●CTPA 10 FLN CTPAL.. .472 12 .039 1.0 0 .002 0.05 ● ● ●CTPA 15 FLN CTPAL.. .630 16 .059 1.5 0 .002 0.05 ● ● ○ ●CTPA 20 FLN CTPAL.. .630 16 .079 2.0 0 .002 0.05 ● ● ● ●CTPA 20 FLN-P CTPAL.. .630 16 .079 2.0 0 .004 0.10 ●CTPW 25 FLN CTPWL.. .787 20 .098 2.5 0 .002 0.05 ●

±.002"

FLKFT, FLKV HolderType

Max Cut-off Dia. GradeItem Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 KM1CTP 15 FLKV CTPL.. .433 11 .059 1.5 20 .000 0.00 ○ ● ○CTPA 10 FLKFT CTPAL.. .472 12 .039 1.0 16 .002 0.05 ●CTPA 15 FLKFT CTPAL.. .630 16 .059 1.5 16 .002 0.05 ●

Flat top

M

±.002"

=0°FLNV, FLS Holder

TypeMax Cut-off Dia. Grade

Item Number (Inch) (㎜) (Inch) (㎜) (Deg.) (Inch) (㎜) DT4 ZM3 VM1 QM3 KM1CTP 15 FLNV CTPL.. .472 12 .059 1.5 0 .000 0.00 ○CTP 20 FLNV CTPL.. .472 12 .079 2.0 0 .000 0.00 ○CTPA 10 FLS CTPAL.. .472 12 .039 1.0 0 .002 0.05 ●CTPA 15 FLS CTPAL.. .630 16 .059 1.5 0 .002 0.05 ●CTPA 20 FLS CTPAL.. .630 16 .079 2.0 0 .002 0.05 ○ ●CTPW 25 FLNV CTPWL.. .787 20 .098 2.5 0 .000 0.00 ●

Flat top

MM

M

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J56

Cut-off / Parting

■CTP / CTPA

■CTPW

CTP / CTPA / CTPW Toolholders

b

AA22

φD

Right-Hand style shown

Right-Hand style shown

(Inch)

Gage Insert φ maxfor holder Item number

StockClamp screw Wrench

R L

CTPFR../FL..

.472 CTP 06-IN ● ● 3/8 3/8 .079 3/8 .217 .591 4.724 LRIS-4 × 10PW CLR-15S

.472 CTP 08-IN ● ● 1/2 1/2 0 1/2 .217 .591 4.724 LRIS-4 × 12PW CLR-15S

.472 CTP 10-IN ● ● 5/8 5/8 0 5/8 .217 .591 4.724 LRIS-4 × 12PW CLR-15S

CTPAFR../FL..

.630 CTPA 06-IN ● ● 3/8 3/8 .079 3/8 .295 .768 4.724 LRIS-4 × 10PW CLR-15S

.630 CTPA 08-IN ● ● 1/2 1/2 0 1/2 .295 .768 4.724 LRIS-4 × 12PW CLR-15S

.630 CTPA 10-IN ● ● 5/8 5/8 0 5/8 .295 .768 4.724 LRIS-4 × 12PW CLR-15S

CTPWFR../FL..

.787 CTPW 08-IN ● ● 1/2 .498 ― .630 .591 ― 4.724 LRIS-4 × 10 LLR-25S

.787 CTPW 10-IN ● ● 5/8 .623 ― .630 .591 ― 4.724 LRIS-4 × 10 LLR-25S

(Metric, ㎜ )

Gage Insert φ maxfor holder Item number

StockClamp screw Wrench

R L

CTPFR../FL..

12 CTP 08 ● ● 8 8 4 10 5.5 15 120 LRIS-4 × 10PW CLR-15S12 CTP 10 ○ ○ 10 10 2 10 5.5 15 120 LRIS-4 × 10PW CLR-15S12 CTP 12 ○ ○ 12 12 0 12 5.5 15 120 LRIS-4 × 12PW CLR-15S12 CTP 16 ○ ○ 16 16 0 16 5.5 15 120 LRIS-4 × 12PW CLR-15S

CTPAFR../FL..

16 CTPA 10 ○ ○ 10 10 2 10 7.5 19.5 120 LRIS-4 × 10PW CLR-15S16 CTPA 12 ● ● 12 12 0 12 7.5 19.5 120 LRIS-4 × 12PW CLR-15S16 CTPA 16 ○ ○ 16 16 0 16 7.5 19.5 120 LRIS-4 × 12PW CLR-15S16 CTPA 20F ○ ○ 20 20 0 20 7.5 19.5 80 LRIS-4 × 10 LLR-25S

CTPWFR../FL..

20 CTPWR10 ○ 10 9.95 ― 12 15 ― 120 LRIS-4 × 10 LLR-25S20 CTPWL10A ○ 10 9.95 ― 16 15 ― 120 LRIS-4 × 10 LLR-25S20 CTPWR12 ○ 12 11.95 ― 12 15 ― 120 LRIS-4 × 10 LLR-25S20 CTPWL12A ○ 12 11.95 ― 16 15 ― 120 LRIS-4 × 10 LLR-25S20 CTPW 16 ○ ○ 16 15.95 ― 16 15 ― 120 LRIS-4 × 10 LLR-25S20 CTPW 20 ○ ○ 20 19.95 ― 20 15 ― 120 LRIS-4 × 10 LLR-25S

●:Stock ○: 1-2 week delivery

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J57

AA

5.51°

φD

■CTPR-SUB / CTPAR-SUB

■CTPL-SUB / CTPAL-SUB

CTPR-SUB / CTPAR-SUB

CTPL-SUB / CTPAL-SUB

φD

.217 (55) 30°

φφ

Sub-chuckGuide bushing

φφ

Sub-chuckGuide bushing

φDsCTPR-SUB:φ1.18"CTPAR-SUB:φ1.42"

φDsCTPL-SUB:φ1.18"CTPAL-SUB:φ1.42"

(Inch)

Gage Insert φ maxfor holder Item number Stock Clamp screw Wrench

CTPFR..

.472 CTPR06-IN-SUB ● 3/8 3/8 .079 3/8 .217 .591 4.724 .630 45 .217 LRIS-4 × 5 LLR-25S

.472 CTPR08-IN-SUB ● 1/2 1/2 0 1/2 .217 .591 4.724 .630 45 .217 LRIS-4 × 5 LLR-25S

.472 CTPR10-IN-SUB ● 5/8 5/8 0 5/8 .217 .591 4.724 .630 45 .217 LRIS-4 × 5 LLR-25S

CTPAFR..

.630 CTPAR06-IN-SUB ● 3/8 3/8 .079 3/8 .295 .768 4.724 .787 25 .217 LRIS-4 × 5 LLR-25S

.630 CTPAR08-IN-SUB ● 1/2 1/2 0 1/2 .295 .768 4.724 .787 25 .217 LRIS-4 × 5 LLR-25S

.630 CTPAR10-IN-SUB ● 5/8 5/8 0 5/8 .295 .768 4.724 .787 25 .217 LRIS-4 × 5 LLR-25S*Also available in 8㎜ (CTP-SUB only),10㎜ and 12㎜ shanks. Please contact NTK for detail.

(Inch, Metric)

Gage Insert φ maxfor holder Item number Stock Clamp

screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CTPFL..

.472(12) CTPL08-SUB ○ .315 8 .315 8 .157 4 .394 10 .217 5.5 .591 15 4.724 120 .630 16 LRIS-4×5 LLR-25S

.472(12) CTPL10GX-SUB ○ .394 10 .394 10 .079 2 .394 10 .217 5.5 .591 15 3.346 85 .630 16 LRIS-4×5 LLR-25S

.472(12) CTPL12GX-SUB ○ .472 12 .472 12 0 0 .472 12 .217 5.5 .591 15 3.346 85 .630 16 LRIS-4×5 LLR-25S

CTPAFL..

.630(16) CTPAL06-IN-SUB ● 3/8 3/8 .079 2 3/8 .295 7.5 .768 19.5 4.724 120 .787 20 LRIS-4×5 LLR-25S

.630(16) CTPAL08-IN-SUB ● 1/2 1/2 0 0 1/2 .295 7.5 .768 19.5 4.724 120 .787 20 LRIS-4×5 LLR-25S

.630(16) CTPAL10-IN-SUB ● 5/8 5/8 0 0 5/8 .295 7.5 .768 19.5 4.724 120 .787 20 LRIS-4×5 LLR-25S*Metric size is available for CTPAL-SUB upon request. Please contact NTK for detail.

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J58

Cut-off / Parting

CTDP Series - Inserts

CTDP Series - Toolholders

(Inch, Metric)

Item numberGrade

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) DM4 TM4 QM3CTDP20N .079 2.0 .752 19.1 0° .002 0.05 ● ○ ●CTDP20N02 .079 2.0 .752 19.1 0° .008 0.20 ● ○ ●CTDP20R6 .079 2.0 .752 19.1 6° .002 0.05 ● ○ ●CTDP20R15 .079 2.0 .752 19.1 15° .002 0.05 ● ○ ●CTDP25N .098 2.5 .835 21.2 0° .002 0.05 ● ○ ●CTDP25N02 .098 2.5 .835 21.2 0° .008 0.20 ● ○ ●CTDP25R6 .098 2.5 .835 21.2 6° .002 0.05 ● ○ ●CTDP25R15 .098 2.5 .835 21.2 15° .002 0.05 ● ○ ●

(Inch, Metric)Gage Insert Item number

Stock φ maxfor holder Clamp screw Wrench

R L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CTDP20

CTDP 06-IN-20D20 ● ● .787(20.0) 3/8 .079 2.0 .394 10 3/8 .400 10.150 .748 19.0 .019 0.5 LRIS-4 × 12 LLR-25SCTDP 08-IN-20D25 ● ● .984(25.0) 1/2 .079 2.0 1/2 1/2 .506 12.850 .866 22.0 0 0 LRIS-4 × 12 LLR-25SCTDP 10-IN-20D32 ● ● 1.260(32.0) 5/8 .079 2.0 5/8 5/8 .631 16.025 1.083 27.5 0 0 LRIS-5 × 10 LLR-28SCTDP 12-IN-20D32 ● ● 1.260(32.0) 3/4 .079 2.0 3/4 3/4 .756 19.200 1.083 27.5 0 0 LRIS-5 × 10 LLR-28S

CTDP20

CTDP 10-20D20 ○ ○.787(20.0)

.394 10 .079 2.0 .394 10 .394 10 .400 10.15 .748 19.0 .079 2 LRIS-4 × 12 LLR-25SCTDP 12-20D20 ○ ○ .472 12 .079 2.0 .472 12 .472 12 .478 12.15 .748 19.0 0 0 LRIS-4 × 12 LLR-25SCTDP 12-20D25 ○ ○

1.000(25.4).472 12 .079 2.0 .472 12 .472 12 .478 12.15 .866 22.0 0 0 LRIS-4 × 12 LLR-25S

CTDP 16-20D25 ○ ○ .630 16 .079 2.0 .630 16 .630 16 .636 16.15 .866 22.0 0 0 LRIS-4 × 12 LLR-25SCTDP 16-20D32A ○ ○

1.260(32.0).630 16 .079 2.0 .630 16 .630 16 .636 16.15 1.083 27.5 0 0 LRIS-5 × 10 LLR-28S

CTDP 2012-20D32A ○ ○ .787 20 .079 2.0 .472 12 .787 20 .478 12.15 1.116 29.5 0 0 LRIS-5 × 10 LLR-28SCTDP 20-20D32A ○ ○ .787 20 .079 2.0 .787 20 .787 20 .793 20.15 1.116 29.5 0 0 LRIS-5 × 10 LLR-28S

CTDP25CTDP 16-25D34A ○ ○

1.339(34.0).630 16 .098 2.5 .630 16 .630 16 .636 16.15 1.083 27.5 0 0 LRIS-5 × 10 LLR-28S

CTDP 2012-25D34A ○ ○ .787 20 .098 2.5 .472 12 .787 20 .478 12.15 1.116 29.5 0 0 LRIS-5 × 10 LLR-28SCTDP 20-25D34A ○ ○ .787 20 .098 2.5 .787 20 .787 20 .793 20.15 1.116 29.5 0 0 LRIS-5 × 10 LLR-28S

.059 (X-.118)

4.729 (120)

Dm

●:Stock ○: 1-2 week delivery

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J59

CTV Series - Inserts

CTV Series - Toolholders

InsertGrade

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) ZM3 QM3CTV25N .098 2.50 .472 12 0° .008 0.20 ○CTV30N .118 3.00 .472 12 0° .008 0.20 ○ ○CTV25R .098 2.50 .472 12 8° .008 0.20 ○CTV30R .118 3.00 .472 12 8° .008 0.20 ○CTV30L .118 3.00 .472 12 8° .008 0.20 ○CTV25R00A .098 2.50 .472 12 8° .002 MAX. 0.05 max. ●CTV30R00A .118 3.00 .472 12 8° .002 MAX. 0.05 max. ○CTV25R00B .098 2.50 .472 12 17° .002 MAX. 0.05 max. ○CTV30R00B .118 3.00 .472 12 17° .002 MAX. 0.05 max. ○

Clamp on typeMax.cut-off diameterφ.906(23) ~φ1.378(35)

.252(639)

12°

90° ±.002"

θ θ

.020(0.5)

φD

Max. cut-off diameter

Right-Hand style shown

CTV..N CTV..R CTV..L

(Inch, Metric)

Gage Insert Max.cut-off diameterφ Item number

Stock Clampscrew Wrench

R L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)CTV25.. .900(22.9) CTV 08B ● □ 1/2 .098 2.5 4.5 114 .945 24 .480 12.2 1/2 1/2 .520 13.2 BS0620 LW-4CTV25..

.906(23)

CTV 16K25S ● .630 16 .098 2.5 4.921 125 .945 24 .480 12.2 .630 16 .630 16 .650 16.5 BS0620 LW-4CTV30.. CTV 16K30S ● .630 16 .118 3.0 4.921 125 .945 24 .480 12.2 .630 16 .630 16 .650 16.5 BS0620 LW-4CTV25.. CTV 20K25S ○ .787 20 .098 2.5 4.921 125 .945 24 .480 12.2 .787 20 .787 20 .807 20.5 BS0620 LW-4CTV30.. CTV 20K30S ○ .787 20 .118 3.0 4.921 125 .945 24 .480 12.2 .787 20 .787 20 .807 20.5 BS0620 LW-4CTV25..

1.378(35)

CTV 16K25 ● ● .630 16 .098 2.5 4.921 125 1.260 32 .728 18.5 .630 16 .630 16 .650 16.5 BS0620 LW-4CTV30.. CTV 16K30 ● ○ .630 16 .118 3.0 4.921 125 1.260 32 .728 18.5 .630 16 .630 16 .650 16.5 BS0620 LW-4CTV25.. CTV 20K25 ● ● .787 20 .098 2.5 4.921 125 1.260 32 .728 18.5 .787 20 .787 20 .807 20.5 BS0620 LW-4CTV30.. CTV 20K30 ○ ○ .787 20 .118 3.0 4.921 125 1.260 32 .728 18.5 .787 20 .787 20 .807 20.5 BS0620 LW-4

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J60

Cut-off / Parting

CSV Series - Inserts All CSV series inserts have polished cutting edges

Toolholders for right-hand inserts CSVR.., DS-CSVL..Toolholders for left-hand inserts CSVL..

Note: All angles shown are obtained when insert is set on the holder All images in this page show right-hand inserts

Item number Chip-breaker

Max. Cut-off Dia. Width VM1(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L

CSVC11F V06 No .118 3 .024 0.6 .079 2.0 0.0 ○CSVC11F V07 No .157 4 .028 0.7 .098 2.5 0.0 ● ●CSVC11F V08 No .157 4 .031 0.8 .098 2.5 0.0 ○ ○CSVC11F V10 No .197 5 .039 1.0 .118 3.0 0.0 ● ●CSVC11F V13 No .197 5 .051 1.3 .118 3.0 0.0 ○ ○CSVC11F VB06 Yes .118 3 .024 0.6 .079 2.0 0.0 ○CSVC11F VB07 Yes .157 4 .028 0.7 .098 2.5 0.0 ●CSVC11F VB08 Yes .157 4 .031 0.8 .098 2.5 0.0 ○CSVC11F VB10 Yes .197 5 .039 1.0 .118 3.0 0.0 ●CSVC11F VB13 Yes .197 5 .051 1.3 .118 3.0 0.0 ○

25°

W±.002"

1/4"

(6.35)

1/4"

(6.35)

CSV Series - Toolholders

■CSVC - Cut-off

■DS-CSVL (Takes right-hand inserts)

■CSV -NC

AA 1°

.7874.724 (120)(20)

.004

(0.1)

AA

.787(20)

4.724 (120)

0.0

1°

φ

■CSV

AA .7875.512 (140)(20)

.004

(0.1)

1°

Right-Hand style shown

CSV -NC (Inch)

Gage Insert Item numberStock Clamp

screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..CSV 06-IN-NC ● ● 3/8 3/8 3/8 0 0 LRIS-2.5 × 7 CLR-15S

CSV 08-IN-NC ● ● 1/2 1/2 1/2 0 0 LRIS-2.5 × 7 CLR-15S

CSV (Metric, ㎜)

Gage Insert Item numberStock Clamp

screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..

CSV 07 ● ● .295 7.5 .295 7.5 .295 7.5 .020 0.5 LRIS-2.5 × 7 CLR-15SCSV 08 ● ● .315 8 .315 8 .315 8 0 0 LRIS-2.5 × 7 CLR-15SCSV 10 ● ● .394 10 .394 10 .394 10 0 0 LRIS-2.5 × 7 CLR-15SCSV 12 ● .472 12 .472 12 .472 12 0 0 LRIS-2.5 × 7 CLR-15S

(Inch)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11FR.. DS-CSVL15 ● 5/8 .591 15 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15S

Mirror finish

●:Stock ○: 1-2 week delivery M: Mirror finish

M

M

M

M

M

M

M

M

M

M

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

J61

■CTPSR

■CTPS

CTPS Series - Inserts

CTPS Series - Toolholders

Max. Cut-off Dia.Item number

Grade(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) ZM3 VM1.157 4.0 CTPS12FR .047 1.2 .138 3.5 16° .002 0.05 ● ○.197 5.0 CTPS15FR .059 1.5 .157 4.0 16° .002 0.05 ● ○.335 8.5 CTPS18FR .071 1.8 .217 5.5 16° .002 0.05 ● ○.394 10.0 CTPS20FR .079 2.0 .236 6.0 16° .002 0.05 ● ○.157 4.0 CTPS12FRV .047 1.2 .138 3.5 20° 0 0 ● ○.197 5.0 CTPS15FRV .059 1.5 .157 4.0 20° 0 0 ○ ○.335 8.5 CTPS18FRV .071 1.8 .217 5.5 20° 0 0 ○ ○.394 10.0 CTPS20FRV .079 2.0 .236 6.0 20° 0 0 ○ ○

〈With Chipbreaker〉 〈Flat-top, No Chipbreaker〉

CTPS..FR CTPS..FRV

Note: θ shows the angle when insert is set on the holder

Screw-on type, Maximum diameter : .394" (10㎜)

±.002"

θ

.787(20)

.098

(2.5)

.236

(6.0)

45°

±.002"

θ

.787(20)

45°

.098(2.5)

.236

(6.0)

AA

4.724(120)197

(5.0)

0.0

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CTPS.. CTPSR06-IN ● 3/8 3/8 3/8 LRIS-2.5 × 7 CLR-15SCTPS.. CTPSR08-IN ● 1/2 1/2 1/2 LRIS-2.5 × 7 CLR-15SCTPS.. CTPSR10 ○ .394 10 .394 10 .394 10 LRIS-2.5 × 7 CLR-15SCTPS.. CTPSR12 ○ .472 12 .472 12 .472 12 LRIS-2.5 × 7 CLR-15S

Mirror finish

M

M

M

M

[ Cut-off / Pa

rting ]

For Swiss-type Lathes

MEMO

J63

Grooving

●Product Lines ………………………J64●Grooving ……………………………J66

J

For Swiss-type Lathes

[ G

roov

ing ]

J64

Grooving

NTK Grooving Tools - Product Lines

GTT DS-GTTL

➡J69 ➡J70Blade width .012" to .118" Blade width .012" to .118"Depth of cut .012" to .106" Depth of cut .012" to .106"Y-axis holders available ➡J70

GTM.., TMG.. GTM32..R, TMG32..R

GTVW GTPA CSV

➡J71 ➡J72 ➡J73Blade width .118" to .236" Blade width .079" to .098" Blade width .010" to .059"Depth of cut .244" to .315" Depth of cut .197" to .236" Depth of cut .006" to .102"

Y-axis holders available ➡J72GVW.. GTPA.. CSVG..

■OD Grooving

[ G

roov

ing ]

For Swiss-type Lathes

J65

SFG

➡J100Blade width .039" to .118"Depth of cut .059" to .118"Min. Bore Dia. φ.236"

BG (Steel Shank)

➡J111Blade width .020" to .079"Depth of cut .047" to .126"Min. Bore Dia. φ.394"

■ID Grooving

■Face Grooving

FGV

➡J77Blade width .039" to .079"Depth of cut .059" to .118"

FGV..DS-FGV

➡J77Blade width .039" to .079"Depth of cut .059" to .157"

FGV.., FBV..

CH-FGV

➡J77Blade width .039" to .079"Depth of cut .059" to .157"

FGV.., FBV..

SBG

➡J100Blade width .020" to .079"Depth of cut .031" to .087"Min. Bore Dia. φ.118"

[ G

roov

ing ]

For Swiss-type Lathes

J66

Grooving

Inserts for GTT Holders■GTMX32-T

Item numberWidth W Max. depth of cut QM3 DT4

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L R LGTMX 32030 T .012 0.30 .010 0.25 .024 0.6 .002 0.05 ● ○GTMX 32033 T .013 0.33 .010 0.25 .024 0.6 .002 0.05 ● ■GTMX 32043 T .017 0.43 .035 0.9 .047 1.2 .002 0.05 ● ○GTMX 32050 T .020 0.50 .035 0.9 .047 1.2 .002 0.05 ● ■ ○GTMX 32053 T .021 0.53 .035 0.9 .047 1.2 .002 0.05 ●GTMX 32065 T .026 0.65 .035 0.9 .047 1.2 .002 0.05 ● ○GTMX 32075 T .030 0.75 .063 1.6 .079 2.0 .002 0.05 ● ● ○ ○GTMX 32080 T .031 0.80 .063 1.6 .079 2.0 .002 0.05 ● ● ○GTMX 32095 T .037 0.95 .063 1.6 .079 2.0 .002 0.05 ○ ○ ○ ○GTMX 32100 T .039 1.00 .063 1.6 .079 2.0 .002 0.05 ● ○GTMX 32100 T01 .039 1.00 .063 1.6 .079 2.0 .004 0.1 ● ○GTMX 32110 T .043 1.10 .063 1.6 .079 2.0 .002 0.05 ○GTMX 32120 T .047 1.20 .063 1.6 .079 2.0 .002 0.05 ● ○GTMX 32120 T01 .047 1.20 .063 1.6 .079 2.0 .004 0.1 ● ○GTMX 32125 T .049 1.25 .063 1.6 .079 2.0 .002 0.05 ● ● ○GTMX 32130 T .051 1.30 .063 1.6 .079 2.0 .002 0.05 ○ ○GTMX 32140 T .055 1.40 .063 1.6 .079 2.0 .002 0.05 ○ ○GTMX 32145 T .057 1.45 .106 2.7 .118 3.0 .002 0.05 ○GTMX 32150 T .059 1.50 .106 2.7 .118 3.0 .002 0.05 ● ● ○ ○GTMX 32150 T01 .059 1.50 .106 2.7 .118 3.0 .004 0.1 ● ● ○GTMX 32150 T02 .059 1.50 .106 2.7 .118 3.0 .008 0.2 ● ○GTMX 32160 T .063 1.60 .106 2.7 .118 3.0 .002 0.05 ● ○GTMX 32175 T .069 1.75 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMX 32180 T .071 1.80 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMX 32200 T .079 2.00 .106 2.7 .118 3.0 .002 0.05 ● ● ○ ○GTMX 32200 T01 .079 2.00 .106 2.7 .118 3.0 .004 0.1 ○ ○ ○ ○GTMX 32200 T02 .079 2.00 .106 2.7 .118 3.0 .008 0.2 ● ○GTMX 32250 T .098 2.50 .106 2.7 .118 3.0 .002 0.05 ● ○ ○ ○GTMX 32250 T01 .098 2.50 .106 2.7 .118 3.0 .004 0.1 ○ ○GTMX 32250 T02 .098 2.50 .106 2.7 .118 3.0 .008 0.2 ○ ○GTMX 32300 T .118 3.00 .106 2.7 .118 3.0 .002 0.05 ● ■ ○GTMX 32300 T01 .118 3.00 .106 2.7 .118 3.0 .004 0.1 □GTMX 32300 T02 .118 3.00 .106 2.7 .118 3.0 .008 0.2 ● ○

Width tolerance w±.001" Side Turning Capable

Toolholders for right-hand inserts GTTR, DS-GTTL, Y-GTTRToolholders for left-hand inserts GTTL

Right-Hand style shown

14°

3/8" 1/8"

14° ±.001"

●:Stock ○: 1-2 week delivery M: Mirror finish

[ G

roov

ing ]

For Swiss-type Lathes

J67

■GTMH32-EWidth tolerance w±.001"

Right-Hand style shown

Item numberWidth W Max depth of cut Grade

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) QM3 ZM3GTMH 32050 RE025 .020 0.50 .035 0.9 .047 1.2 .010 0.25 ● ●GTMH 32070 RE035 .028 0.70 .063 1.6 .079 2.0 .014 0.35 ●GTMH 32100 RE05 .039 1.00 .063 1.6 .079 2.0 .020 0.50 ● ●GTMH 32150 RE075 .059 1.50 .106 2.7 .118 3.0 .030 0.75 ●GTMH 32200 RE10 .079 2.00 .106 2.7 .118 3.0 .039 1.00 ● ○GTMH 32300 RE15 .118 3.00 .106 2.7 .118 3.0 .059 1.50 ● ○

Item numberWidth W Max depth of cut Grade

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) VM1GTMH 32033 RVT .013 0.33 .010 0.25 .024 0.6 0 0 ●GTMH 32043 RVT .017 0.43 .035 0.9 .047 1.2 0 0 ●GTMH 32053 RVT .021 0.53 .063 1.6 .079 2.0 0 0 ●GTMH 32065 RVT .026 0.65 .063 1.6 .079 2.0 0 0 ●GTMH 32075 RVT .030 0.75 .063 1.6 .079 2.0 0 0 ●GTMH 32080 RVT .031 0.80 .063 1.6 .079 2.0 0 0 ●GTMH 32085 RVT .033 0.85 .063 1.6 .079 2.0 0 0 ●GTMH 32100 RVT .039 1.00 .063 1.6 .079 2.0 0 0 ●GTMH 32150 RVT .059 1.50 .106 2.7 .118 3.0 0 0 ●GTMH 32200 RVT .079 2.00 .106 2.7 .118 3.0 0 0 ●

Full Radius Groover

① To perform side turning with an insert whose groove width is greater than 0.43㎜ (.017"), set side turning feed rate to 0.03㎜/rev (.001in/rev) or smaller.

② On performing side turning with an insert whose groove width is greater than 0.43㎜ (.017") at the feed rate over 0.03㎜/rev (.001in/rev) (0.1㎜/rev (.004in/rev) max), it is likely that chip damages grooved sides. In this case, please perform grooving by two or more passes to make room for chips before performing side turning.

■Tips for Cutting Condition Selection (GTMH32-(V)T style inserts)

20°

■GTMH32-VTWidth tolerance w±.001"

Right-Hand style shown

Side Turning Capable

3/8" 1/8"

14°±.001"

14°

3/8" 1/8"

±.001"

Mirror finish

M

M

M

M

M

M

M

M

M

M

[ G

roov

ing ]

For Swiss-type Lathes

J68

Grooving■TMG32-E/GTMH32-U ■GTMH32-E

TMG32-E (Inch)Width W Max depth of cut

ZM3Item number R L

TMG 32031 E01 .031 .063 .079 .004 ● ●TMG 32039 E01 .039 .063 .079 .004 ● ●TMG 32049 E01 .049 .063 .079 .004 ● ●TMG 32062 E02 .062 .106 .118 .008 ● □TMG 32079 E02 .079 .106 .118 .008 ● □TMG 32094 E02 .094 .106 .118 .008 ●TMG 32125 E02 .125 .106 .118 .008 ● □

GTMH32-E Width W Max depth of cut ZM3Item number (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L

GTMH 32033 E .013 0.33 .012 0.3 .024 0.6 .001 0.03 ○ ○GTMH 32043 E .017 0.43 .035 0.9 .047 1.2 .001 0.03 ● ○GTMH 32053 E .021 0.53 .035 0.9 .047 1.2 .002 0.05 ○ ○GTMH 32075 E .030 0.75 .063 1.6 .079 2.0 .002 0.05 ○ ○GTMH 32095 E .037 0.95 .063 1.6 .079 2.0 .002 0.05 ○ ○GTMH 32100 E .039 1.00 .063 1.6 .079 2.0 .002 0.05 ○ ○GTMH 32100 E01 .039 1.00 .063 1.6 .079 2.0 .004 0.1 ○ ○GTMH 32120 E .047 1.20 .063 1.6 .079 2.0 .002 0.05 ● ○GTMH 32120 E01 .047 1.20 .063 1.6 .079 2.0 .004 0.1 ○ ○GTMH 32140 E .055 1.40 .063 1.6 .079 2.0 .002 0.05 ○ ○GTMH 32150 E .059 1.50 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32150 E01 .059 1.50 .106 2.7 .118 3.0 .004 0.1 ○ ○GTMH 32180 E .071 1.80 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32200 E .079 2.00 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32200 E01 .079 2.00 .106 2.7 .118 3.0 .004 0.1 ○ ○GTMH 32225 E .089 2.25 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32250 E .098 2.50 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32275 E .108 2.75 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32300 E .118 3.00 .106 2.7 .118 3.0 .002 0.05 ○ ○

GTMH32-U Width W Max depth of cut ZM3Item number (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L

GTMH 32030 U .012 0.30 .012 0.3 .024 0.6 .001 0.03 ○ ○GTMH 32050 U .020 0.50 .035 0.9 .047 1.2 .002 0.05 ● ○GTMH 32075 U .030 0.75 .063 1.6 .079 2.0 .002 0.05 ● ○GTMH 32095 U .037 0.95 .063 1.6 .079 2.0 .002 0.05 ○ ○GTMH 32100 U .039 1.00 .063 1.6 .079 2.0 .002 0.05 ● ○GTMH 32103 U .041 1.03 .063 1.6 .079 2.0 .002 0.05 ○GTMH 32125 U .049 1.25 .063 1.6 .079 2.0 .002 0.05 ○ ○GTMH 32145 U .057 1.45 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32150 U .059 1.50 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32175 U .069 1.75 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32200 U .079 2.00 .106 2.7 .118 3.0 .002 0.05 ○ ○GTMH 32250 U .098 2.50 .106 2.7 .118 3.0 .002 0.05 ○ ○

3/8" 1/8"

20°+.002"- 0

14°3/8" 1/8"

±.001"20°

Width tolerance w+.002" -0 Width tolerance w±.001"

●:Stock ○: 1-2 week delivery □ To be discontinued

[ G

roov

ing ]

For Swiss-type Lathes

J69

GTT Toolholders Screw accessible from both side Shank.315(8㎜)~.630(16㎜)Without offset

A A

0.0

4.724(120)

591(15)

Max groove depth

Right-Hand style shown

(Inch)

Gage Insert Item numberStock Groove width range

(W)  Clamp screw Wrench

R L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TMG32..GTM..32..

GTT 06A-IN ● ● .012 ~ .118 0.30 ~ 3.00 .079 2 3/8 3/8 .118 3 LR-S-4 × 10PW CLR-15SGTT 08A-IN ● ● .012 ~ .118 0.30 ~ 3.00 .079 2 1/2 1/2 .039 1 LR-S-4 × 10PW CLR-15SGTT 10A-IN ● ● .012 ~ .118 0.30 ~ 3.00 .079 2 5/8 5/8 0 0 LR-S-4 × 10PW CLR-15SGTT 12A-IN ● .012 ~ .118 0.30 ~ 3.00 .079 2 3/4 3/4 0 0 LR-S-4 × 10PW CLR-15SGTT 06B-IN ● ● .057 ~ .118 1.45 ~ 3.00 .118 3 3/8 3/8 .118 3 LR-S-4 × 10PW CLR-15SGTT 08B-IN ● ● .057 ~ .118 1.45 ~ 3.00 .118 3 1/2 1/2 .039 1 LR-S-4 × 10PW CLR-15SGTT 10B-IN ● ● .057 ~ .118 1.45 ~ 3.00 .118 3 5/8 5/8 0 0 LR-S-4 × 10PW CLR-15SGTT 12B-IN ● .057 ~ .118 1.45 ~ 3.00 .118 3 3/4 3/4 0 0 LR-S-4 × 10PW CLR-15S

(Metric, ㎜)

Gage Insert Item numberStock Groove width range

(W)  Clamp screw Wrench

R L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TMG32..GTM..32..

GTT 08K00 ● ○ .012 ~ .118 0.30 ~ 3.00 .079 2 .315 8 .315 8 .197 5 LR-S-4 × 10PW CLR-15SGTT 10K00 ○ ○ .012 ~ .118 0.30 ~ 3.00 .079 2 .394 10 .394 10 .118 3 LR-S-4 × 10PW CLR-15SGTT 12K00 ● ○ .012 ~ .118 0.30 ~ 3.00 .079 2 .472 12 .472 12 .039 1 LR-S-4 × 10PW CLR-15SGTT 16K00 ● ○ .012 ~ .118 0.30 ~ 3.00 .079 2 .630 16 .630 16 0 0 LR-S-4 × 10PW CLR-15SGTT 10K15 ○ ○ .057 ~ .118 1.45 ~ 3.00 .118 3 .394 10 .394 10 .118 3 LR-S-4 × 10PW CLR-15SGTT 12K15 ○ ○ .057 ~ .118 1.45 ~ 3.00 .118 3 .472 12 .472 12 .039 1 LR-S-4 × 10PW CLR-15SGTT 16K15 ● ○ .057 ~ .118 1.45 ~ 3.00 .118 3 .630 16 .630 16 0 0 LR-S-4 × 10PW CLR-15SGTT 10K25 ○ ○ .098 ~ .118 2.50 ~ 3.00 .118 3 .394 10 .394 10 .118 3 LR-S-4 × 10PW CLR-15SGTT 12K25 ○ ○ .098 ~ .118 2.50 ~ 3.00 .118 3 .472 12 .472 12 .039 1 LR-S-4 × 10PW CLR-15SGTT 16K25 ○ ○ .098 ~ .118 2.50 ~ 3.00 .118 3 .630 16 .630 16 0 0 LR-S-4 × 10PW CLR-15S

Note: Modification is required to groove deeper than ar[ G

roov

ing ]

For Swiss-type Lathes

J70

Grooving■DS-GTTL

■Y-GTTR ■Y-GTTR-OH

Max. depth of cut: .079" (2.0㎜)

Note: DS-GTTL holders take right-hand inserts

Max. depth of cut: .079" (2.0㎜) Coolant through for high-pressure coolant

A A

φ0.0

.079

(2.0) .787

(20)Max. grooving depth

A

B B

A

0.0

0.0

.079

(2.0)

.787

(20)

4.724(120)

Max. grooving depth

B

A A

B

2.756 (70)

0.0

Right-Hand style shown Right-Hand style shown

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TMG32..R..GTM..32..R..

DS-GTTL16X ○ .630 16 .591 15 3.740 95 .236 6 LR-S-4 × 5.8 RLR-20S

DS-GTTL19 ● 3/4 .709 18 4.724 120 .236 6 LR-S-4 × 5.8 RLR-20S

DS-GTTL20 ○ .787 20 .748 19 4.724 120 .236 6 LR-S-4 × 5.8 RLR-20S

DS-GTTL22 ● .866 22 .827 21 4.724 120 .236 6 LR-S-4 × 5.8 RLR-20S

DS-GTTL25 ● 1 .945 24 4.724 120 .394 10 LR-S-4 × 5.8 RLR-20S

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TMG32..R..GTM..32..R..

Y-GTTR06-IN ● 3/8 3/8 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR08-IN ● 1/2 1/2 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR10-IN ● 5/8 5/8 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR10 ○ .394 10 .394 10 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR12 ○ .472 12 .472 12 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR12SOH* ○ .472 12 .472 12 .787 20 LR-S-4 × 10PW CLR-15S

*Comes with coolant through

Feed direcition

Gang tooling post

●:Stock ○: 1-2 week delivery

[ G

roov

ing ]

For Swiss-type Lathes

J71

GVW Series - Inserts■GVWGroove Width Tolerance w±.001"

Item NumberGrade

(Inch) (㎜) (Inch) (㎜) QM3GVW300N02 .118 3.0 .008 0.2 ●GVW300N04 .118 3.0 .016 0.4 ●GVW400N02 .157 4.0 .008 0.2 ●GVW400N04 .157 4.0 .016 0.4 ●GVW500N02 .197 5.0 .008 0.2 ○GVW500N04 .197 5.0 .016 0.4 ○GVW600N02 .236 6.0 .008 0.2 ○GVW600N04 .236 6.0 .016 0.4 ○

.787(20)

±.001"

GTVW Series - Toolholders

(Inch, Metric)

Gage Insert Item numberStock , Clamp Screw Spring WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

GVW300

GTVW 1016-3 ○ ○ .394 10 .630 16 .244 6.2 .768 19.5 .071 1.8 CVSR/L3 AOS-5X16 ASG-5 LW-2.5SGTVW 1216-3 ● ○ .472 12 .630 16 .244 6.2 .768 19.5 .071 1.8 CVSR/L3 AOS-5X16 ASG-5 LW-2.5SGTVW 1616-3 ● ○ .630 16 .630 16 .315 8.0 .866 22 .071 1.8 CVSR/L3 AOS-5X20 ASG-5 LW-2.5SGTVW 2020-3 ○ ○ .787 20 .787 20 .315 8.0 .866 22 .071 1.8 CVSR/L3 AOS-5X20 ASG-5 LW-2.5S

GVW400GVW500

GTVW 1016-4 ○ ○ .394 10 .630 16 .244 6.2 .768 19.5 .091 2.3 CVSR/L4 AOS-5X16 ASG-5 LW-2.5SGTVW 1216-4 ● ○ .472 12 .630 16 .244 6.2 .768 19.5 .091 2.3 CVSR/L4 AOS-5X16 ASG-5 LW-2.5SGTVW 1616-4 ● ○ .630 16 .630 16 .315 8.0 .866 22 .091 2.3 CVSR/L4 AOS-5X20 ASG-5 LW-2.5SGTVW 2020-4 ○ ○ .787 20 .787 20 .315 8.0 .866 22 .091 2.3 CVSR/L4 AOS-5X20 ASG-5 LW-2.5S

GVW600

GTVW 1020-6 ○ ○ .394 10 .787 20 .244 6.2 .768 19.5 .130 3.3 CVSR/L6 AOS-5X16 ASG-5 LW-2.5SGTVW 1220-6 ○ ○ .472 12 .787 20 .244 6.2 .768 19.5 .130 3.3 CVSR/L6 AOS-5X16 ASG-5 LW-2.5SGTVW 1620-6 ○ ○ .630 16 .787 20 .315 8.0 .866 22 .130 3.3 CVSR/L6 AOS-5X20 ASG-5 LW-2.5SGTVW 2020-6 ○ ○ .787 20 .787 20 .315 8.0 .866 22 .130 3.3 CVSR/L6 AOS-5X20 ASG-5 LW-2.5S

■GTVWClamp-on type

A A

4.274(120)

Max. Depth

[ G

roov

ing ]

For Swiss-type Lathes

J72

Grooving

GTPA Series - Inserts■GTPA

Item numberMax. Depth of Cut Grade

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) PD1 KM1GTPA20FRN01 .079 2.0 .157 4.0 PD1: .197

KM1: .236PD1: 5.0KM1: 6.0

.004 max.(Less than .004)

0.1 max.(Less than 0.1)

○ ○GTPA25FRN01 .098 2.5 .118 3.0 ○ ○

362(9.2)

37(9.4)

20°

45°

±.002"

138

(3.5)

PD1 insert shownShape

236(6.0)

GTPA Series - Toolholders Screw accessible from both sides

■GTPA

2.52.5

.295(7.5)

.004

(0.1)

4.724(120)

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

GTPA

GTPAR1010 ○ .394 10 .394 10 .394 10 LRIS-4 × 10PW CLR-15S

GTPAR1212 ○ .472 12 .472 12 .472 12 LRIS-4 × 12PW CLR-15S

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

GTPA

Y-GTPAR1216 ○ .472 12 .630 16 .787 20 LRIS-4 × 12PW CLR-15S

Y-GTPA 1216SOH* ○ .472 12 .630 16 .787 20 LRIS-4 × 12PW CLR-15S

Y-GTPA 1616OH* ○ .630 16 .630 16 .787 20 LRIS-4 × 12PW CLR-15S

*Comes with coolant through

■Y-GTPA

A

A

.004(0.1) 4.724

(120)

1.063

(27)

■Y-GTPA-OHY-GTPAR1216SOH

Coolant hole position

6

16

12

6AA

B

B

0.0

2.756(70)

.004(0.1)

Coolant through for high-pressure coolant

●:Stock ○: 1-2 week delivery M: Mirror finish

[ G

roov

ing ]

For Swiss-type Lathes

J73

All CSV series inserts have polished cutting edges.CSV Series - Inserts

AA

.787(20)

4.724 (120)

0.0

1°

φ

(Inch)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..FR DS-CSVL15 ● 5/8 .591 15 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15S

■DS-CSVL (Takes right-hand inserts)

CSV -NC (Inch)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..CSV 06-IN-NC ● ● 3/8 3/8 3/8 0 0 LRIS-2.5 × 7 CLR-15S

CSV 08-IN-NC ● ● 1/2 1/2 1/2 0 0 LRIS-2.5 × 7 CLR-15S

CSV (Metric, ㎜)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..

CSV 07 ● ● .295 7 .295 7 .295 7 .020 0.5 LRIS-2.5 × 7 CLR-15SCSV 08 ● ● .315 8 .315 8 .315 8 0 0 LRIS-2.5 × 7 CLR-15SCSV 10 ● ● .394 10 .394 10 .394 10 0 0 LRIS-2.5 × 7 CLR-15SCSV 12 ● .472 12 .472 12 .472 12 0 0 LRIS-2.5 × 7 CLR-15S

CSV Series - Toolholders

Right-Hand style shown

■CSV

AA .7875.512 (140)(20)

.004

(0.1)

1°

AA 1°

.7874.724 (120)(20)

.004

(0.1)

■CSV -NC

Toolholders for right-hand inserts CSVR.., DS-CSVL..Toolholders for left-hand inserts CSVL..

Note: All angles shown are obtained when insert is set on the holder All images in this page show right-hand inserts

■CSVG - Grooving Item number Width Max. Depth of Cut VM1(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L

CSVG11F V025 .010 0.25 .006 0.15 .020 0.50 0 ●CSVG11F V030 .012 0.30 .006 0.15 .020 0.50 0 ○CSVG11F V035 .014 0.35 .006 0.15 .020 0.50 0 ●CSVG11F V040 .016 0.40 .006 0.15 .020 0.50 0 ○CSVG11F V045 .018 0.45 .018 0.45 .039 1.00 0 ●CSVG11F V050 .020 0.50 .018 0.45 .039 1.00 0 ●CSVG11F V055 .022 0.55 .018 0.45 .039 1.00 0 ○CSVG11F V060 .024 0.60 .018 0.45 .039 1.00 0 ●CSVG11F V065 .026 0.65 .018 0.45 .039 1.00 0 ○CSVG11F V070 .028 0.70 .018 0.45 .039 1.00 0 ●CSVG11F V075 .030 0.75 .050 1.40 .079 2.00 0 ● ○CSVG11F V080 .031 0.80 .050 1.40 .079 2.00 0 ○CSVG11F V085 .033 0.85 .050 1.40 .079 2.00 0 ○CSVG11F V090 .035 0.90 .050 1.40 .079 2.00 0 ○CSVG11F V095 .037 0.95 .050 1.40 .079 2.00 0 ● ○CSVG11F V100 .039 1.00 .050 1.40 .079 2.00 0 ●CSVG11F V110 .043 1.10 .102 2.60 .118 3.00 0 ○CSVG11F V120 .047 1.20 .102 2.60 .118 3.00 0 ● ○CSVG11F V130 .051 1.30 .102 2.60 .118 3.00 0 ●CSVG11F V140 .055 1.40 .102 2.60 .118 3.00 0 ○CSVG11F V150 .059 1.50 .102 2.60 .118 3.00 0 ●

1/4"

(6.35)

w

L

+.001"

-0

Mirror finish

MMMMMMMMMMMMMMMMMMMMM

[ G

roov

ing ]

For Swiss-type Lathes

J74

Grooving

Steel(Carbon Steel, Alloy Steel)

Stainless Steel(Excluding 303 SS)

Free Cutting Steel(Including 303 SS)

Non-ferrous Metals(Brass, Aluminum, Copper)

Speed (SFM) 160 (100 - 330) 130 (100 - 330) 200 (100 - 330) 260 (160 - 390)

FeedRate(IPR)

GrooveDepth(Inch)

.039 .001 (.0004-.002) .0008 (.0004-.002) .002 (.0004-.0025) .002 (.0004-.0025)

.059 .0008 (.0004-.002) .0004 (.0002-.001) .001 (.0004-.002) .001 (.0004-.002)

.079 .0004 (.0002-.001) .0004 (.0002-.001) .0008 (.0004-.002) .0008 (.0004-.002)

☆Tips for Successful Face Grooving①Run multiple passes for turn wider grooves. Make sure to groove from outer diameter to inner diameter to avoid any interference.②If lines appear on the boss section (as shown at right), slow down feed rate on retracting the tool.③If scratch appears at the end of the boss, slow down feed rate.④If groove surface looks torn, either slow down feed rate or increase speed.⑤If groove bottom looks torn under slow speed and feed condition, increase speed.

☆NoteSide turning cannot be performed with FGV style tooling

SATURN DUO Face grooving tool

●FGV type for face grooving and FBV type for face machining●Economical double-corner specification●Improved tool rigidity by optimizing the overhang and holder shape●Gang-type, front-gang-type and sleeve holder types available

Features

Holder : L-hand Insert : L-hand

Holder : R-hand Insert : R-hand

Shape ofgrooved face

Holder : R-hand Insert : R-hand

Concavedface shape

FGV type for face grooving FBV type for face machiningTarget work shape Target work shape

・Grooving possible under a wide range of cutting conditions due to strengthened rigidity of both inserts and holders・Minimum machining diameter from φ.236", groove width from .039"・Left-hand types available for machining works with a boss

・Further improved face machining efficiency・Minimum machining diameter from φ.315"

■Recommended Cutting Condition for FGV Style Tooling (for Face Grooving)

[ G

roov

ing ]

For Swiss-type Lathes

J75

☆Machining process•For materials with good machinability, it is possible to machine up to .157"(4㎜) deep at a low feed rate in a single pass for both longitudinal feed and cross feed.

Note) Cutting in Z-direction is expressed as the longitudinal feed, and cutting in X-direction is expressed as the cross feed in this section.

☆Useful tips for machining

When burrs occur on ID surface, it is recommended to perform cutting in 2 passes, one for roughing and one for finishing as shown in the following procedure:

 ☆ Example of 2-pass machining: Leane .008"(0.2㎜) on roughing then run a finish cut

.157 (4)

φ.3

15 (8

)

.112

(3.0

4)

Longitudinal feed

Cutting in Z direction : Longitudinal feed

.157(4)

φ.3

15 (8

)Cross feed

.010

(0.2

5)

Cutting in X direction : Cross feed

φ.3

15 (8

)

.037 (0.8)

❶ Longitudinal feed (roughing)

30°

φ.3

15 (8

)

❷ Longitudinal feed (finishing)

φ.3

15 (8

)

φ.3

31 (8

.4)

❸Slant machining (roughing)

φ.3

31(8

.4)

.010

(0.2

5)

❹Cross feed (finishing)

■Recommended Cutting Conditions for FBV style Tooling (for Face Grooving)Minimum machining diameter:φ.315" (8㎜ ) WET

Inserts ➡ X00 Holders ➡ X00

Steel(Carbon Steel, Alloy Steel)

Stainless Steel(Excluding 303 SS)

Free Cutting Steel(Including 303 SS)

Non-ferrous Metals(Brass, Aluminum, Copper)

Speed (SFM) 160 (100 - 330) 130 (100 - 330) 200 (100 - 330) 260 (160 - 390)

FeedRate(IPR)

GrooveDepth(Inch)

.039 .001 (.0004-.002) .0008 (.0004-.002) .002 (.0004-.0025) .002 (.0004-.0025)

.059 .0008 (.0004-.002) .0004 (.0002-.001) .001 (.0004-.002) .001 (.0004-.002)

.079 .0004 (.0002-.001) .0004 (.0002-.001) .0008 (.0004-.002) .0008 (.0004-.002)* When machining difficult materials where chip control is problematic (such as 304SS), it is recommended that the machining be carried out in several stages.

[ G

roov

ing ]

For Swiss-type Lathes

J76

Grooving

Item numberI.C. Thickness Grade

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) TM4

Right-Hand Insert

.039 1.0 FGV100RB00D6 1/4 6.35 3/32 2.38 .059 1.5 .000 0.00 .236 6.0 ○

.039 1.0 FGV100RB05D6 1/4 6.35 3/32 2.38 .059 1.5 .002 0.05 .236 6.0 ○

.059 1.5 FGV150RB00D6 1/4 6.35 3/32 2.38 .079 2.0 .000 0.00 .236 6.0 ○

.059 1.5 FGV150RB05D6 1/4 6.35 3/32 2.38 .079 2.0 .002 0.05 .236 6.0 ○

.079 2.0 FGV200RB00D6 1/4 6.35 3/32 2.38 .118 3.0 .000 0.00 .236 6.0 ○

.079 2.0 FGV200RB05D6 1/4 6.35 3/32 2.38 .118 3.0 .002 0.05 .236 6.0 ○

Left-Hand Insert

.039 1.0 FGV100LB00D6 1/4 6.35 3/32 2.38 .059 1.5 .000 0.00 .236 6.0 ○

.039 1.0 FGV100LB05D6 1/4 6.35 3/32 2.38 .059 1.5 .002 0.05 .236 6.0 ○

.059 1.5 FGV150LB00D6 1/4 6.35 3/32 2.38 .079 2.0 .000 0.00 .236 6.0 ○

.059 1.5 FGV150LB05D6 1/4 6.35 3/32 2.38 .079 2.0 .002 0.05 .236 6.0 ○

.079 2.0 FGV200LB00D6 1/4 6.35 3/32 2.38 .118 3.0 .000 0.00 .236 6.0 ○

.079 2.0 FGV200LB05D6 1/4 6.35 3/32 2.38 .118 3.0 .002 0.05 .236 6.0 ○

Item numberI.C. Thickness Grade

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) TM4

.020 0.5 FBV40R05D8AM3 1/4 6.35 3/32 2.38 .157 4.0 .002 0.05 .315 8.0 ○

.020 0.5 FBV40R15D8AM3 1/4 6.35 3/32 2.38 .157 4.0 .006 0.15 .315 8.0 ○

Right-Hand style shown

w

I.C.

■FBV

w

wrεrε

w

w

I.C.

Right-Hand style shown

Width Tolerance w±.001"■FGV

FGV / FBV (Saturn Duo) - Face Grooving Inserts

Left-Hand style shown

●:Stock ○: 1-2 week delivery

[ G

roov

ing ]

For Swiss-type Lathes

J77

■DS-FGV

■FGV

■CH-FGV

FGV / FBV (Saturn Duo) - Toolholders

AA

BB

Holder: LHInsert: LH

Holder: RHInsert: RH

Holder: RHInsert: RH

AA

0.0

11.0

Holder: LHInsert: LH

Holder: RHInsert: RH

Holder: RHInsert: RH

Square shank toolholders for gang type tool posts (Designed exclusively for LEFT-hand FGV inserts)

Round shank toolholders for drill sleeves

Square shank toolholders for FGV and FBV inserts

Right-Hand style shown

Right-Hand style shown

Right-Hand style shown

Note: Right-hand toolholders take LEFT-hand inserts for this style

(Inch, Metric)

Gage Insert Item numberStock Clamp

screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

FGV...LFGVR1016 ○ .413 10 0 0 .630 16 4.724 120 .787 20 0 0 LRIS-2.5 × 7 CLR-15SFGVR1216 ○ .472 12 0 0 .630 16 4.724 120 .787 20 0 0 LRIS-2.5 × 7 CLR-15SFGVR1616 ○ .630 16 0 0 .630 16 4.724 120 .787 20 0 0 LRIS-2.5 × 7 CLR-15S

FGVFBV

DS-FGV 19 ○ ○ 3/4 .709 18 .709 18 4.724 120 .118 3.0 LRIS-2.5 × 7 CLR-15SDS-FGV 20 ○ ○ .787 20 .748 19 .748 19 4.724 120 .118 3.0 LRIS-2.5 × 7 CLR-15SDS-FGV 22 ○ ○ .866 22 .827 21 .827 21 4.724 120 .118 3.0 LRIS-2.5 × 7 CLR-15SDS-FGV 25 ○ ○ 1 .965 24.5 24.5 4.724 120 .118 3.0 LRIS-2.5 × 7 CLR-15SCH-FGV 1010 ○ ○ .413 10 .394 10 .394 10 4.724 120 .709 18 .413 10.5 LRIS-2.5 × 7 CLR-15SCH-FGV 1212 ○ ○ .472 12 .472 12 .472 12 4.724 120 .709 18 .492 12.5 LRIS-2.5 × 7 CLR-15SCH-FGV 1616 ○ ○ .630 16 .630 16 .630 16 4.724 120 .709 18 .650 16.5 LRIS-2.5 × 7 CLR-15S

[ G

roov

ing ]

For Swiss-type Lathes

MEMO

J79

Threading

●Product Lines ………………………J80●Threading …………………………J82●Thread Whirling …………………J86

J

For Swiss-type Lathes

[ Threa

ding

J80

Threading

Thread Whirling System

➡J86TW..

SBT

➡J101Applicable Pitch 50 to 16 TPI

L1 .031" to .071"

CSV

➡J85Applicable Pitch 125 to 51 TPI

L1 .118"CSVT..

TTP DS-TTP

➡J83 ➡J83Applicable Pitch 127 to 13 TPI

L1 .217"TTP..F..

■ OD Threading

■ ID Threading

NTK Threading Tool - Product Lines● Sharp cutting edge brings burr-free finish● Wide coverage in pitch range

P(Pitch)L1

TGC (Carbide shank)

➡J112Applicable Pitch 63 to 34 TPI

L1 .028" to .039"TMN..

[ Threa

ding

]For Swiss-type Lathes

J81

■ Metric (M) Threads / Fine and Coarse

Thread Type Pitch (㎜)2.00 1.50 1.25 1.00 0.80 0.75 0.70 0.50 0.40 0.35 0.25 0.20

M1 Coarse FineM2 Coarse FineM3 Coarse FineM4 Coarse FineM5 CoarseM6 Coarse

Fine

M7M8 Coarse

Fine

M9M10 Coarse Fine

M11M12

Fine

FineM14 CoarseM15

M16 CoarseM17

M18

FineM20

M22M24

M25M26

M27

Fine FineM28M30

M32

TTP60F -N02 can be used up to M150 when the pitch is 2.0 ㎜

Inserts Pitch (㎜)TTP60F 4A,AS(B,BS) 0.2-0.75TTP60F 8A,AS(B,BS) 0.4-1.25TTP60F -N(S) 1.0-1.5TTP60F -N02 1.5-2.0

Covered Thread Pitch Range (㎜)

Thread Type Pitch(㎜) Applicable Inserts

Coa

rse (U

NC)

No.1-64 UNC 0.3969 TTP60F 4A, AS(B, BS)No.2-56 UNC 0.4536

TTP60F 4A, AS(B, BS)TTP60F 8A, AS(B, BS)

No.3-48 UNC 0.5292 No.4-40 UNC 0.6350 No.5-40 UNC 0.6350 No.6-32 UNC 0.7938

TTP60F 8A, AS(B, BS)No.8-32 UNC 0.7938 No.10-24 UNC 1.0583

TTP60F 8A, AS(B, BS)TTP60F -N(S)

No.12-24 UNC 1.0583 1/4-20 UNC 1.2700 5/16-18 UNC 1.4111 TTP60F -N(S)3/8-16 UNC 1.5875

TTP60F -N027/16-14 UNC 1.8143 1/2-13 UNC 1.9538

■ Unified Standard (UN, UNF, UNC) Threads

Thread Type Pitch(㎜) Applicable Inserts

Fine

(UNF)

No.0-80 UNF 0.3175 TTP60F 4A, AS(B, BS)No.1-72 UNF 0.3528

No.2-64 UNF 0.3969 No.3-56 UNF 0.4536

TTP60F 4A, AS(B, BS)TTP60F 8A, AS(B, BS)

No.4-48 UNF 0.5292 No.5-44 UNF 0.5773 No.6-40 UNF 0.6350 No.8-36 UNF 0.7056 No.10-32 UNF 0.7938

TTP60F 8A, AS(B, BS)No.12-28 UNF 0.9071 1/4-28 UNF 0.9071 5/16-24 UNF 1.0583 TTP60F 8A, AS(B, BS)

TTP60F -N(S)3/8-24 UNF 1.0583 7/16-20 UNF 1.2700

TTP60F -N(S)1/2-20 UNF 1.2700 9/16-18 UNF 1.4111 5/8-18 UNF 1.4111 3/4-16 UNF 1.5875

TTP60F -N027/8-14 UNF 1.8143

TTP Style

[ Threa

ding

]For Swiss-type Lathes

J82

Threading

TTP Series - Inserts

Pitch range Item number Edgeconfig.

QM3 ZM3Pitch(㎜) TPI (Inch) (㎜) (Inch) (㎜) R L R L

60° 0.2 ~ 0.75 127 ~ 34 TTP60F 4A A .016 0.4 .002MAX Flat

0.05MAX Flat ● ● ● ●

60° 0.2 ~ 0.75 127 ~ 34 TTP60F 4B B .016 0.4 .002MAX Flat

0.05MAX Flat ● ● ● ●

60° 0.5 ~ 1.25 50 ~ 21 TTP60F 8A A .031 0.8 R.002 0.05 ● ● ● ●

60° 0.5 ~ 1.25 50 ~ 21 TTP60F 8B B .031 0.8 R.002 0.05 ● ○ ● ●

60° 1.0 ~ 1.5 25 ~ 17 TTP60F -N N .049 1.25 R.004 0.10 ● ● ● ●

60° 1.5 ~ 2.0 16 ~ 13 TTP60F -N02 N .049 1.25 R.008 0.20 ● ● ○ ○

55° 0.2 ~ 0.75 127 ~ 34 TTP55F 8A A .031 0.8 R.002 0.05 ● ●

55° 0.2 ~ 0.75 127 ~ 34 TTP55F 8B B .031 0.8 R.002 0.05 ● ●

with flat with radius

Right-Hand style shown

■TTP

.780(20.0)

50°

.098

(2.5)

θ°θ°

θ°

Edge Shape

[A type]

[B type]

[N type]

.310

(8.0)

Right Hand Toolholders Left Hand Toolholders

Toolholder TTPR Toolholder TTPR Toolholder TTPL Toolholder TTPL

Insert TTP..FR..A Insert TTP..FR..B Insert TTP..FL..B Insert TTP..FL..A

Edge Shape:A type

Edge Shape:A type

Edge Shape:B type

Edge Shape:B type

Guide Bushing

●:Stock ○: 1-2 week delivery

[ Threa

ding

]For Swiss-type Lathes

J83

Right-Hand style shown

TTP Series - Toolholders■TTP

■DS-TTPL

Screw accessible from both side

.276(7)4.724(120)

.591(15)

.256(6.5)

Max. shoulder

clearance

LeftHand

RightHand

.217(5.5)

0.0

.787(20)

φ

Left-Hand style shown

(Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TTP55FR/LTTP60FR/L

TTP 06-IN ● ● 3/8 3/8 3/8 .079 2 LRIS-4 × 10PW CLR-15STTP 08-IN ● ● 1/2 1/2 1/2 0 0 LRIS-4 × 12PW CLR-15STTP 10-IN ● ● 5/8 5/8 5/8 0 0 LRIS-4 × 12PW CLR-15S

TTP55FR/L..TTP60FR/L..

TTP 08 ● ● .315 8 .394 10 .315 8 .157 4 LRIS-4 × 10PW CLR-15STTP 12 ○ ○ .472 12 .472 12 .472 12 0 0 LRIS-4 × 10PW CLR-15STTP 16 ○ ○ .630 16 .630 16 .630 16 0 0 LRIS-4 × 10PW CLR-15S

(Metric, ㎜)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TTP55FR..TTP60FR..

DS-TTPL19 ● 3/4 .709 18 4.724 120 .394 10 LRIS-4 × 10 LLR-25S

DS-TTPL20 ● .787 20 .748 19 4.724 120 .394 10 LRIS-4 × 10 LLR-25S

DS-TTPL22 ● .866 22 .827 21 4.724 120 .394 10 LRIS-4 × 10 LLR-25S

DS-TTPL25 ● 1 .945 24 5.906 150 .394 10 LRIS-4 × 10 LLR-25S

[ Threa

ding

]For Swiss-type Lathes

J84

Threading

CSVT Style

Thread Type Pitch(㎜)

Total DOC(㎜)

Number of pass 1 2 3 4 5 6 7 8 9 10

Metric (60°) malethread

0.20 0.20 4 0.08 0.06 0.04 0.02 0.25 0.24 4 0.10 0.08 0.04 0.02 0.30 0.28 5 0.08 0.07 0.07 0.04 0.02 0.35 0.32 5 0.10 0.09 0.07 0.04 0.02 0.40 0.35 5 0.12 0.10 0.07 0.04 0.02 0.45 0.39 5 0.16 0.10 0.07 0.04 0.02 0.50 0.33 5 0.10 0.10 0.07 0.04 0.02 0.60 0.40 6 0.10 0.10 0.08 0.06 0.04 0.02 0.70 0.48 6 0.10 0.10 0.10 0.10 0.06 0.02 0.75 0.52 7 0.10 0.10 0.10 0.08 0.07 0.05 0.02 0.80 0.56 7 0.10 0.10 0.10 0.10 0.08 0.06 0.02 1.00 0.71 8 0.15 0.15 0.12 0.10 0.08 0.06 0.03 0.02 1.25 0.90 9 0.20 0.18 0.13 0.10 0.10 0.07 0.05 0.05 0.02 1.50 1.09 10 0.22 0.20 0.15 0.12 0.10 0.10 0.08 0.05 0.05 0.02

TTP, TTPS, TTMH, TTMA, CSVT Partial profile 60 degree inserts

■ Recommended Depth of Cut (DOC) for Each Pass(㎜)

Pitch (㎜ )0.50 0.40 0.35 0.25 0.20

M1 Coarse FineM2 Coarse FineM3 Coarse FineM4

FineM5

■ Metric (M) Threads / Fine and Coarse

Thread TypePitch (㎜ )

#1 #2

CoarseNo.1-64 UNC 0.3969

No.2-56 UNC 0.4536

Fine

No.0-80 UNF 0.3175No.1-72 UNF 0.3528

No.2-64 UNF 0.3969No.3-56 UNF 0.4536

■ Unified Standard (UN, UNF, UNC) Threads

●:Stock ○: 1-2 week delivery M: Mirror finish

[ Threa

ding

]For Swiss-type Lathes

J85

CSV Series - Inserts All CSV series inserts have polished cutting edges

Toolholders for right-hand inserts CSVR.., DS-CSVL..Toolholders for left-hand inserts CSVL..

Note: All angles shown are obtained when insert is set on the holderAll images in this page show right-hand inserts

Item number Chipbreaker Pitch range VM1(Inch) (㎜) R L

CSVT11F P60-035A No 125 TPI ~ 51 TPI .001MAX 0.03MAX ● ●CSVT11F P60-035B No 125 TPI ~ 51 TPI .001MAX 0.03MAX ● ●

.014±.001

(1.0)

.039

60°

1/4"

(6.35)

.014±.001

(1.0)

.039

60°

type A

type B

CSV Series - Toolholders

■DS-CSVL (Takes right-hand inserts)

■CSV -NC

■CSVT - Threading

AA 1°

.7874.724 (120)(20)

.004

(0.1)

AA

.787(20)

4.724 (120)

0.0

1°

φ

■CSV

AA .7875.512 (140)(20)

.004

(0.1)

1°

Right-Hand style shown

CSV (Metric, ㎜)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..

CSV 07 ● ● .295 7 .295 7 .295 7 .020 0.5 LRIS-2.5 × 7 CLR-15SCSV 08 ● ● .315 8 .315 8 .315 8 0 0 LRIS-2.5 × 7 CLR-15SCSV 10 ● ● .394 10 .394 10 .394 10 0 0 LRIS-2.5 × 7 CLR-15SCSV 12 ● .472 12 .472 12 .472 12 0 0 LRIS-2.5 × 7 CLR-15S

CSV -NC (Inch)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..CSV 06-IN-NC ● ● 3/8 3/8 3/8 0 0 LRIS-2.5 × 7 CLR-15S

CSV 08-IN-NC ● ● 1/2 1/2 1/2 0 0 LRIS-2.5 × 7 CLR-15S

DS-CSVL (Inch)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11FR.. DS-CSVL15 ● 5/8 .591 15 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15S

Mirror finish

M

M

[ Threa

ding

]For Swiss-type Lathes

J86

Threading

●Reduce cycle time by more than half*● .256" (6.5㎜ ) thick inserts accommodate large pitch and lead

* Applies to cycle time for thread whirling only Does not apply to total cycle time. Actual results may vary

NTK Thread Whirling - Nonstop improvement to meet tighter-than-ever demands from quality oriented customers

●Dramatically improved productivity in thread forming operations

●NTK's unique design technology (patented) makes precise and correct inserts possible, the first time, without any redesign and remake

●Excellent surface finish and longer tool life than competitors'

●Sharp cutting edges for reduced tool pressure and superior chip control

Features

Form multiple-lead threads in a single-pass

Double-lead threads Triple-lead threads

Work Bone screw Worm gear

Work material Ti-6Al-4V ELI brass

Work appearance

Insert appearance

Major Dia. φ.157"(4.0㎜) φ.278"(7.0㎜)

Minor Dia. φ.094"(2.4㎜) φ.185"(4.7㎜)

Pitch φ.135"(3.42㎜) φ.193"(4.9㎜)

Patented

NTK’s Unique Attachment System

Mutiple-Lead Thread Whirling

① Loosen the Mounting Bolts ② Rotate the Insert Holder to 10 degrees ③ Pull the Whirling Insert Holder without pull out the Mounting Bolts

Insert HolderMount Adapter

InsertInsert Holder Mounting Bolt

NTK’s whirling insert holder can be attached and detached without removing mounting bolts

Adapter Mounting Bolt

Thread Whirling

●:Stock ○: 1-2 week delivery

[ Threa

ding

]For Swiss-type Lathes

J87

NTK thread whirling inserts are all made to order (except for the ISO style threads shown below). Please follow the procedure to order correct NTK thread whirling systems and inserts.

Thread Whirling Order Procedure

Recommended Cutting Conditions

Recommended cutting conditionsWhirling cutter RPM Main spindle RPM Feed Rate

1,000-4,000 min-1 10-30 min-1 Same as thread pitch(for single-lead threads)

Typical worksDiameter Work Materials

φ0.118 to φ0.394 inch(For cutters with 12㎜ ID)

Titanium, Titanium alloy,316 Stainless

■Standard thread whirling inserts for ISO style threads

Item number e P r4 r5 Thread type Callout

GradeZM3

TW5835-HA1.5-D12 1.5 0-0.15 1.1 0-0.1 0.1 0.5 0.3 0.1 35° 3° HA1.5

ISO5835

TW5835-HA2.0-D12 2.0 0-0.15 1.3 0-0.1 0.1 0.6 0.4 0.1 35° 3° HA2.0 ○

TW5835-HA2.7-D12 2.7 0-0.15 1.9 0-0.15 0.1 1 0.6 0.2 35° 3° HA2.7 ○

TW5835-HA3.5-D12 3.5 0-0.15 2.4 0-0.15 0.1 1.25 0.8 0.2 35° 3° HA3.5 ○

TW5835-HA4.0-D12 4.0 0-0.15 2.9 0-0.15 0.1 1.5 0.8 0.2 35° 3° HA4.0 ○

TW5835-HA4.5-D12 4.5 0-0.15 3.0 0-0.15 0.1 1.75 1 0.3 35° 3° HA4.5 ○

TW5835-HA5.0-D12 5.0 0-0.15 3.5 0-0.15 0.1 1.75 1 0.3 35° 3° HA5.0 ○

TW5835-HB4.0-D12 4.0 0-0.15 1.9 0-0.15 0.1 1.75 0.8 0.3 25° 5° HB4.0 ○

TW5835-HB6.5-D12 6.5 0-0.15 3.0 0-0.15 0.2 2.75 1.2 0.8 25° 5° HB6.5 ○

TW9268-HC2.9-D12 2.79 to 2.9 2.03 to 2.18 0.1max 1.06 ― ― ― ― HC2.9

ISO9268

TW9268-HC3.5-D12 3.43 to 3.53 2.51 to 2.64 0.1max 1.27 ― ― ― ― HC3.5

TW9268-HC3.9-D12 3.78 to 3.91 2.77 to 2.92 0.1max 1.27 ― ― ― ― HC3.9

TW9268-HC4.2-D12 4.09 to 4.22 2.95 to 3.25 0.1max 1.27 ― ― ― ― HC4.2

TW9268-HD4.0-D12 4.0±0.03 2.92±0.03 0.1 1.59 ― ― 45° 10° HD4.0

TW9268-HD4.5-D12 4.5±0.03 2.92±0.03 0.1 2.18 ― ― 45° 10° HD4.5

°

ISO5835 HA ISO5835 HB ISO9268 HC ISO9268 HD

(Note: Must be used with thread whirling cutters with 12㎜ φDm dimension. See next page to find φDm for each cutter.)

⑴  Fill out the NTK Thread Whirling Quote Request Form (The form is available at www.ntkcuttingtools.com/whirling)⑵  Send the form and a full part drawing to NTK by e-mail ([email protected]) or by fax (see the back cover)⑶ The quote for NTK thread whirling tooling will be issued through your local NTK distributor⑷ Use the item numbers shown in the quote to place an order⑸  After NTK thread whirling tooling arrived, make sure to use the helix angle provided by NTK to set up, and run your jobs

[ Threa

ding

]For Swiss-type Lathes

J88

Threading

P.C.D.

φ φ

P.C.D.

φ φ

P.C.D.

φ φ

P.C.D.

φφ

φ φ P.C.D.

φ φ

Type 1 Type 3Type 2

Type 4 Type 5 Type 6

Thread Whiring System

Machinemake Model Location Spindle

make Spindle model Helix angle NTKThread whirling system Stock Type No. of

toothφ(㎜) Mount adapter bolt

CITIZEN

L20E/L20X Gang

CITIZEN

BTW-3000 0°- 15° TWC9C0746HP1 ● 1 9 φ12 M3A20

Gang

BTW-2000 ±25°TWC9C1040HP1TWC6C1040HP1TWC9C1040HP1-D16

●●○

1969

φ12φ12φ16

M3(Provided with spindle)

M432 0°- 25°C32

BTW-1000±25°L20

M20 +20°- -25°M332 ±25°C12/16 Gang

CITIZEN

LTR0170

±15° TWC9C1037P2 ● 2 9 φ12 CS0310(M3)M12/16Turret

LTR0168M12/16 MSW105M20/32 KSW110L20 Gang LTR0183 ±15° TWC9J1040P2 ● 2 9 φ12 H-M4 × 12M20/32M20/32 Turret LTR0169K16 Attachment PCM GSW-101 ±15° TWC6P1620HP1-D9 ● 1 6 φ9 M4(Provided with spindle)L20 Gang LSW-101-L20 ±10° TWC9P1340P2 ● 2 9 φ12 M4(Provided with spindle)

STAR

ECAS-12/20 Attachment

STAR

54178 ±10°

TWC9S1640P2 ● 3 9 φ12 CS04148S(M4)

SR-20J/20RⅢ 54172 -20°- 0°(*)ECAS-20T

Turret

59172 ±20°ECAS-32T 58171 ±10°ST-38 43156 ±10°SV-12 45172 ±10°SV-20 42173 ±10°SV-32 43172 ±10°

TSUGAMI

BH20/BH38 Turret

TSUGAMI

3263-Y481 ±10° TWC9TS2252P2 ● 3 9 φ12 CS0515(M5)BS20 Attachment 3214-Y1371 ±10° TWC9TS20550P2 ● 3 9 φ16 CS0515(M5)S205S206B0205 Attachment

3281-Y451(S205・S206)3220-Y6541(B0205)

0°- 10° TWC9TS2244HP1 ● 4 9 φ12 CS0520(M5)0°- 20° TWC9TS1944HP1 ● 4 9 φ12 CS0520(M5)0°- 25° TWC9TS1644HP1 ● 4 9 φ12 CS0515(M5)0°- 30° TWC9TS1044HP1 ● 4 9 φ12 CS0515(M5)

SS20/SS26SS32 3268-Y451 0°- 10° TWC9TS1952P2BK ● 4 9 φ12 CS0515(M5)

0°- 20° TWC9TS1652P2BK ● 4 9 φ12 CS0515(M5)SS207 ─ ─ 0°- 15° TWC4TS3010HP1 ● 5 4 φ7 For single-corner inserts only

TORNOS

DECO 10/10a

Attachment TORNOS

224-1900 ±15° TWC6TO11542HP1 ● 4 6 φ12 CS0410(M4)Evo DECO 10/10 242-1900DECO 13a/13e 226-1900

±15° TWC9TO10540P2 ● 3 9 φ12 CS0410(M4)Evo DECO 16/10 243-1900DECO 20a 223-1900DECO 26a 225-1900Sigma 20 234-2750 ± 25° TWC9TO12050P2-D18 ● 3 9 φ18 CS0410(M4)Sigma 32 236-2750

HASEGAWA JS-1W ─ HASEGAWA ─ 0°- 20° TWC9HA22594P2 6 9 φ16 CS0620(M6)*:May not work for over 15 deg. helix angle

■Spare Insert Holder (Cartridge)

Item number No. of tooth φ(㎜) Compatible cutters

TWC6HP2 6 12 For Type 2 and Type 3*

TWC9HP2 9 12 For Type 2 and Type 3*

TWC9HP2-D16 9 12 For Type 6

■Spare Parts

Description Item number

Insert ScrewFor 4㎜ thick inserts FSI17-2.2×6.0For 6.5㎜ thick inserts FSI24-2.2×7.9Wrench T-07

Insert Holder Mounting Bolt CS0309-TWNote: Insert holder comes with insert screws and wrench   Insert holder mouting bolt is not included*Cannot be used for TWC9TS20550P2 and TWC9TO12050P2-D18

●:Stock ○: 1-2 week delivery

[ Threa

ding

]For Swiss-type Lathes

J89

Application Examples(㎜)

Worm screw ● Work Material:brassBar Stock Dia. φ7 Number of start 2

Major Dia. φ6 Helix Angle 10.1°

Minor Dia. φ4 Hand of thread Left

Cutting conditionMain Spindle Speed

(min-1) 30 Speed of whirling cutter(min-1) 3,200

Lead=Feed(㎜/rev) 2.8

NTKThread Whirling

9-inserts25 sec

Single-point cutting 50 sec

NTK Thread Whirling reduced total cycle-time by half from single-point screw cutting

Bone screw ● Work Material:316 StainlessBar Stock Dia. φ8 Number of start 1Major Dia. φ3.45 Helix Angle 7.5°Minor Dia. φ2.67 Hand of thread Right

Cutting conditionMain Spindle Speed

(min-1) 23 Speed of whirling cutter(min-1) 2,000

Pitch=Feed(㎜/rev) 1.24

NTKThread Whirling

9-inserts2600 pcs

Competitor's Thread Whirling 6-inserts  1000 pcs

NTK thread whirling resulted up to 2.6 times better tool life than competitor's

Pin ● Work Material:HastelloyBar Stock Dia. φ3 Number of start 1

Major Dia. φ1.5 Helix Angle 4.3°

Minor Dia. φ1.1 Hand of thread Right

Cutting conditionMain Spindle Speed

(min-1) 20 Speed of whirling cutter(min-1) 2,250

Pitch=Feed(㎜/rev) 0.3

NTKThread Whirling

9-inserts600 pcs

Single-point cutting  100 pcs

NTK Thread Whirling offered long tool life for hard-to-cut material "Hastelloy"

Bone screw ● Work Material:316 StainlessBar Stock Dia. φ6.35 Number of start 1Major Dia. φ3.23 Helix Angle 8.5°Minor Dia. φ2.2 Hand of thread Right

Cutting conditionMain Spindle Speed

(min-1) 15 Speed of whirling cutter(min-1) 2,250

Pitch=Feed(㎜/rev) 1.27

NTKThread Whirling

9-inserts1200 pcs

Competitor's Thread Whirling 12-inserts 1000 pcs

Competitor's Thread Whirling 3-inserts  400 pcs

NTK thread whirling resulted up to 3 times better tool life than competitor's

Applicable Thread Geometry (Approximated)

●Helix Angle~About 30° (Subject to machine and spindle specifications)

●Thread Height~About 0.098 inch

●Pitch~About 0.138 inch●Depth of Cut~About 0.157 inch per side

●Number of threads Acceptable as the situation demands

●Bar Stock Diameter ~Aboutφ0.394 inch (For cutters with 12mm ID)

The geometries shown above are approximated and could vary by actual applications

[ Threa

ding

]For Swiss-type Lathes

MEMO

J91

ID Tooling

●Product Lines ………………………J92●Solid Carbide Bars(STICK DUO) …J94

●Boring ●Grooving ●Threading

●Solid Carbide Inserts …………… J104●Boring

●Boring Bars With Indexable Inserts … J106 (Mogul Bar)

●Boring ●Grooving ●Threading

J

For Swiss-type Lathes

[ ID

Too

ling ]

J92

ID Tooling

SBFS (Solid carbide bars)

Min. Bore Dia. φ.079"

SBFB (Solid carbide bars)

Min. Bore Dia. φ.079"

NTK ID Tooling - Product Lines

"S" chip breaker

Sharp cutting edge

"H" Flat type

Mirror finish edge

"F" chip breaker

Evacuates chips BACKWARD

Stick Duo Hyper comes with superior repeatability than conventional Stick Duo

SHFS (Solid carbide bars)

Min. Bore Dia. φ.079"

Hyper

Stick Duo Hyper comes with superior repeatability than conventional Stick Duo

SHFB (Solid carbide bars)

Min. Bore Dia. φ.079"

Hyper

LBMA/LBMA-S DS-LBMB

Min. Bore Dia. φ.039" Min. Bore Dia. φ.039"

■ Minimum Bore Diameter: φ.039" to .323" Solid Carbide Type

➡J105 ➡J105

➡J94 ➡J98

➡J94 ➡J98

[ ID

Too

ling ]

For Swiss-type Lathes

J93

■ Minimum Bore Diameter: φ.197" - MogulBar - Boring bars with indexable inserts

SBG/SFG

Min. Bore Dia. φ.118"

BG (Steel shank)

Min. Bore Dia. φ.394"

SBT

Min. Bore Dia. φ.118"

TGC (Carbide shank)HN59 (Steel shank)

Min. Bore Dia. φ.315"

■ ID Grooving ■ ID Threading

C-MBR (Carbide shank) S-MBR (Steel shank) C-SEXR (Carbide shank) S-SEXR (Steel shank)

Min. Bore Dia. φ.197" Min. Bore Dia. φ.197" Min. Bore Dia. φ.236" Min. Bore Dia. φ.236"

➡J106 ➡J106 ➡J107 ➡J107

C-STUC/P (Carbide shank) S-STUC/P (Steel shank) C-SCLC/P (Carbide shank) S-SCLC/P (Steel shank)

Min. Bore Dia. φ.315" Min. Bore Dia. φ.315" Min. Bore Dia. φ.276" Min. Bore Dia. φ.276"

➡J109 ➡J108➡J109 ➡J108

➡J100 ➡J111 ➡J101 ➡J112

C-STZ (Carbide shank)

Min. Bore Dia. φ.394"

➡J109

[ ID

Too

ling ]

For Swiss-type Lathes

J94

ID Tooling

(Inch, Metric)

Item NumberMin Bore Dia.

ChipbreakerGrade

(Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) TM4SHFS020R005S .079 2 .087 2.2 50 10 0.9 1.8 0.25 .002 0.05 Type S ●

SHFS025R005S .098 2.5 .106 2.7 50 12.5 1.15 2.3 0.30 .002 0.05 Type S ●

SHFS025R015S .098 2.5 .106 2.7 50 12.5 1.15 2.3 0.30 .006 0.15 Type S ●

SHFS030R005S .118 3 .126 3.2 50 15 1.4 2.7 0.40 .002 0.05 Type S ●

SHFS030R015S .118 3 .126 3.2 50 15 1.4 2.7 0.40 .006 0.15 Type S ●

SHFS035R005S .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.40 .002 0.05 Type S ●

SHFS035R015S .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.40 .006 0.15 Type S ●

SHFS040R005S .157 4 .165 4.2 60 20 1.9 3.6 0.45 .002 0.05 Type S ●

SHFS040R015S .157 4 .165 4.2 60 20 1.9 3.6 0.45 .006 0.15 Type S ●

SHFS050R005S .197 5 .205 5.2 70 25 2.4 4.5 0.50 .002 0.05 Type S ●

SHFS050R015S .197 5 .205 5.2 70 25 2.4 4.5 0.50 .006 0.15 Type S ●

■SHFS-S type(for ID Boring) / Minimum Boring Diameter .087" (2.2㎜)Hyper

(Inch, Metric)

Item NumberMin Bore Dia.

ChipbreakerGrade

(Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) TM4SHFB020R005F .087 2 .087 2.2 50 8 0.95 1.8 0.25 .002 0.05 Type F ●

SHFB025R005F .098 2.5 .106 2.7 50 12.5 1.2 2.3 0.30 .002 0.05 Type F ●

SHFB025R015F .098 2.5 .106 2.7 50 12.5 1.2 2.3 0.30 .006 0.15 Type F ●

SHFB030R005F .118 3 .126 3.2 50 15 1.4 2.7 0.45 .002 0.05 Type F ●

SHFB030R015F .118 3 .126 3.2 50 15 1.4 2.7 0.45 .006 0.15 Type F ●

SHFB035R005F .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.50 .002 0.05 Type F ●

SHFB035R015F .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.50 .006 0.15 Type F ●

SHFB040R005F .157 4 .165 4.2 60 20 1.9 3.6 0.50 .002 0.05 Type F ●

SHFB040R015F .157 4 .165 4.2 60 20 1.9 3.6 0.50 .006 0.15 Type F ●

SHFB050R005F .197 5 .205 5.2 70 25 2.4 4.5 0.70 .002 0.05 Type F ●

SHFB050R015F .197 5 .205 5.2 70 25 2.4 4.5 0.70 .006 0.15 Type F ●

■SHFB-F type(for ID Boring) / Minimum Boring Diameter .087" (2.2㎜)

2°30°

Evacuate chips backward

●:Stock ○: 1-2 week delivery M: Mirror finish

[ ID

Too

ling ]

For Swiss-type Lathes

J95

(Inch, Metric)

Item NumberMin Bore Dia.

ChipbreakerGrade

(Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) TM4SHFS020R005H .079 2 .087 2.2 50 10 0.9 1.8 0.25 .002 0.05 None ●

SHFS025R005H .098 2.5 .106 2.7 50 12.5 1.15 2.3 0.30 .002 0.05 None ●

SHFS025R015H .098 2.5 .106 2.7 50 12.5 1.15 2.3 0.30 .006 0.15 None ●

SHFS030R005H .118 3 .126 3.2 50 15 1.4 2.7 0.40 .002 0.05 None ●

SHFS030R015H .118 3 .126 3.2 50 15 1.4 2.7 0.40 .006 0.15 None ●

SHFS035R005H .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.40 .002 0.05 None ●

SHFS035R015H .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.40 .006 0.15 None ●

SHFS040R005H .157 4 .165 4.2 60 20 1.9 3.6 0.45 .002 0.05 None ●

SHFS040R015H .157 4 .165 4.2 60 20 1.9 3.6 0.45 .006 0.15 None ●

SHFS050R005H .197 5 .205 5.2 70 25 2.4 4.5 0.50 .002 0.05 None ●

SHFS050R015H .197 5 .205 5.2 70 25 2.4 4.5 0.50 .006 0.15 None ●

■SHFS-H type(for ID Boring) / Minimum Boring Diameter .087" (2.2㎜)

■Cutting Conditions ➡J19

Mirror finish

M

M

M

M

M

M

M

M

M

M

M

[ ID

Too

ling ]

For Swiss-type Lathes

J96

ID Tooling■HY-NBH / Toolholders Available Shank Size .630" (16㎜) to .1" (25.4㎜) Diameter

Item Number Stockφ φ φ Clamp Screws

(Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) ① ② ③HY-NBH02016H ○ .079 2.0 .630 16 11 15 100 15 9.5 SS04045FS SS0406F SS0404FHY-NBH02516H ○ .098 2.5 .630 16 11.5 15 100 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03016H ○ .118 3.0 .630 16 12 15 100 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03516H ○ .138 3.5 .630 16 12.5 15 100 20 12 SS04045FS SS0404F SS0404FHY-NBH04016H ○ .157 4.0 .630 16 13 15 100 20 12 SS04045FS SS0404F SS0404FHY-NBH05016H ○ .197 5.0 .630 16 14 15 100 20 12 SS04045FS SS0404F SS0404FHY-NBH02019K ● .079 2.0 3/4 11 18 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH02519K ● .098 2.5 3/4 11.5 18 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03019K ● .118 3.0 3/4 12 18 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03519K ● .138 3.5 3/4 12.5 18 125 20 12 SS04045FS SS0406F SS0404FHY-NBH04019K ● .157 4.0 3/4 13 18 125 20 12 SS04045FS SS0406F SS0404FHY-NBH05019K ● .197 5.0 3/4 14 18 125 20 12 SS04045FS SS0406F SS0404FHY-NBH02020K ○ .079 2.0 .787 20 11 19 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH02520K ○ .098 2.5 .787 20 11.5 19 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03020K ○ .118 3.0 .787 20 12 19 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03520K ○ .138 3.5 .787 20 12.5 19 125 20 12 SS04045FS SS0406F SS0404FHY-NBH04020K ○ .157 4.0 .787 20 13 19 125 20 12 SS04045FS SS0406F SS0404FHY-NBH05020K ○ .197 5.0 .787 20 14 19 125 20 12 SS04045FS SS0406F SS0404FHY-NBH02022K ● .079 2.0 .866 22 11 21 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH02522K ● .098 2.5 .866 22 11.5 21 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03022K ● .118 3.0 .866 22 12 21 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03522K ● .138 3.5 .866 22 12.5 21 125 20 12 SS04045FS SS0406F SS0404FHY-NBH04022K ● .157 4.0 .866 22 13 21 125 20 12 SS04045FS SS0406F SS0404FHY-NBH05022K ● .197 5.0 .866 22 14 21 125 20 12 SS04045FS SS0406F SS0404FHY-NBH02025K-MET ○ .079 2.0 .984 25 11 24 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH02525K-MET ○ .098 2.5 .984 25 11.5 24 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03025K-MET ○ .118 3.0 .984 25 12 24 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03525K-MET ○ .138 3.5 .984 25 12.5 24 125 20 12 SS04045FS SS0406F SS0404FHY-NBH04025K-MET ○ .157 4.0 .984 25 13 24 125 20 12 SS04045FS SS0406F SS0404FHY-NBH05025K-MET ○ .197 5.0 .984 25 14 24 125 20 12 SS04045FS SS0406F SS0404FHY-NBH02025K ● .079 2.0 1 11 24 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH02525K ● .098 2.5 1 11.5 24 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03025K ● .118 3.0 1 12 24 125 15 9.5 SS04045FS SS0406F SS0404FHY-NBH03525K ● .138 3.5 1 12.5 24 125 20 12 SS04045FS SS0406F SS0404FHY-NBH04025K ● .157 4.0 1 13 24 125 20 12 SS04045FS SS0406F SS0404FHY-NBH05025K ● .197 5.0 1 14 24 125 20 12 SS04045FS SS0406F SS0404F

■Spare Parts

Item Description Item Number

Overhang Adjustment Ball Screw SS0812R

Ball Screw Fixture SS0808F

Clamp Screw Wrench LW-2

Please refer to φ to find correct-size inserts (bars)

4

201 3 2

φD1

φD

2

φh

h

L1

L2

L3

●:Stock ○: 1-2 week delivery

Hyper

[ ID

Too

ling ]

For Swiss-type Lathes

J97

●Boring Tool Clamping Procedure

①Position the overhang adjustment ball screw to determine overhang amount②Slide the ball screw fixture to secure the ball screw location③Insert a boring bar (tool)Note: Make sure to insert the boring bar correctly so that the rake faces toward the side where clamp screws are

located

**④Positioning Clamp Screw ⑤Clamp Screw ①Overhang Adjustment Ball Screw

③Boring Bar(Tool)

⑥Side Clamp Screw ②Ball Screw Fixture

④Secure the boring bar by tightening the positioning clamp screw ▲

Recommended Clamping Torque:17.7 lb in** Make sure to clamp the boring bar so that flat surface of the bar makes proper contacts with clamp screws

RakeClamp Screws Caution: Improper installation dramatically increases

the chance of chipping cutting edge

Correct Incorrect

⑤Secure the boring bar by tightening the remaining clamp screws ▲

Recommended Clamping Torque:17.7 lb in ⑥ Even if 4 and 5 cannot be applied due to tool clearance and layout, the tool can be used only by using side clampOnce the initial setup is complete, repeat the above procedures 3 thru 5 for each index

Improper clamping of boring bar causes unstable centerline height and offset

●When tool is installed upside down

Toolholder must be installed so that clamp screws and rake of the tool face toward the same side

Rake

Clamp Screws

Installation Procedure for STICK DUO Hyper

[ ID

Too

ling ]

For Swiss-type Lathes

J98

ID Tooling

(Inch, Metric)

Item NumberMin Bore Dia.

ChipbreakerGrade

(Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) ZM3SBFB020R005F .087 2 .087 2.2 50 8 0.95 1.8 0.25 .002 0.05 Type F ○SBFB025R005F .098 2.5 .106 2.7 50 12.5 1.2 2.3 0.30 .002 0.05 Type F ○SBFB025R015F .098 2.5 .106 2.7 50 12.5 1.2 2.3 0.30 .006 0.15 Type F ○SBFB030R005F .118 3 .126 3.2 50 15 1.4 2.7 0.45 .002 0.05 Type F ○SBFB030R015F .118 3 .126 3.2 50 15 1.4 2.7 0.45 .006 0.15 Type F ○SBFB035R005F .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.50 .002 0.05 Type F ○SBFB035R015F .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.50 .006 0.15 Type F ○SBFB040R005F .157 4 .165 4.2 60 20 1.9 3.6 0.50 .002 0.05 Type F ○SBFB040R015F .157 4 .165 4.2 60 20 1.9 3.6 0.50 .006 0.15 Type F ○SBFB050R005F .197 5 .205 5.2 70 25 2.4 4.5 0.70 .002 0.05 Type F ○SBFB050R015F .197 5 .205 5.2 70 25 2.4 4.5 0.70 .006 0.15 Type F ○SBFB060R005F .236 6 .244 6.2 80 30 2.9 5.4 0.90 .002 0.05 Type F ○SBFB060R015F .236 6 .244 6.2 80 30 2.9 5.4 0.90 .006 0.15 Type F ○

■SBFB-F type / Minimum Boring Diameter .087" (2.2㎜)

Evacuate chips backward

(Inch, Metric)

Item NumberMin Bore Dia.

ChipbreakerGrade

(Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) ZM3SBFS020R005S .079 2 .087 2.2 50 10 0.9 1.8 0.25 .002 0.05 Type S ○SBFS025R005S .098 2.5 .106 2.7 50 12.5 1.15 2.3 0.30 .002 0.05 Type S ○SBFS025R015S .098 2.5 .106 2.7 50 12.5 1.15 2.3 0.30 .006 0.15 Type S ○SBFS030R005S .118 3 .126 3.2 50 15 1.4 2.7 0.40 .002 0.05 Type S ○SBFS030R015S .118 3 .126 3.2 50 15 1.4 2.7 0.40 .006 0.15 Type S ○SBFS035R005S .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.40 .002 0.05 Type S ○SBFS035R015S .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.40 .006 0.15 Type S ○SBFS040R005S .157 4 .165 4.2 60 20 1.9 3.6 0.45 .002 0.05 Type S ○SBFS040R015S .157 4 .165 4.2 60 20 1.9 3.6 0.45 .006 0.15 Type S ○SBFS050R005S .197 5 .205 5.2 70 25 2.4 4.5 0.50 .002 0.05 Type S ○SBFS050R015S .197 5 .205 5.2 70 25 2.4 4.5 0.50 .006 0.15 Type S ○SBFS060R005S .236 6 .244 6.2 80 30 2.9 5.4 0.60 .002 0.05 Type S ○SBFS060R015S .236 6 .244 6.2 80 30 2.9 5.4 0.60 .006 0.15 Type S ○

■SBFS-S type / Minimum Boring Diameter .087" (2.2㎜)

●:Stock ○: 1-2 week delivery M: Mirror finish

[ ID

Too

ling ]

For Swiss-type Lathes

J99

(Inch, Metric)

Item NumberMin Bore Dia.

ChipbreakerGrade

(Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) ZM3SBFS020R005H .079 2 .087 2.2 50 10 0.9 1.8 0.25 .002 0.05 None ○SBFS025R005H .098 2.5 .106 2.7 50 12.5 1.15 2.3 0.30 .002 0.05 None ○SBFS025R015H .098 2.5 .106 2.7 50 12.5 1.15 2.3 0.30 .006 0.15 None ○SBFS030R005H .118 3 .126 3.2 50 15 1.4 2.7 0.40 .002 0.05 None ○SBFS030R015H .118 3 .126 3.2 50 15 1.4 2.7 0.40 .006 0.15 None ○SBFS035R005H .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.40 .002 0.05 None ○SBFS035R015H .138 3.5 .146 3.7 60 17.5 1.65 3.2 0.40 .006 0.15 None ○SBFS040R005H .157 4 .165 4.2 60 20 1.9 3.6 0.45 .002 0.05 None ○SBFS040R015H .157 4 .165 4.2 60 20 1.9 3.6 0.45 .006 0.15 None ○SBFS050R005H .197 5 .205 5.2 70 25 2.4 4.5 0.50 .002 0.05 None ○SBFS050R015H .197 5 .205 5.2 70 25 2.4 4.5 0.50 .006 0.15 None ○SBFS060R005H .236 6 .244 6.2 80 30 2.9 5.4 0.60 .002 0.05 None ○SBFS060R015H .236 6 .244 6.2 80 30 2.9 5.4 0.60 .006 0.15 None ○SBFS080R005H .315 8 .323 8.2 80 30 3.9 7.3 0.80 .002 0.05 None ○SBFS080R015H .315 8 .323 8.2 80 30 3.9 7.3 0.80 .006 0.15 None ○

■SBFS-H type / Minimum Boring Diameter .087" (2.2㎜)

Mirror finish

M

M

M

M

M

M

M

M

M

M

M

M

M

M

M

[ ID

Too

ling ]

For Swiss-type Lathes

J100

ID Tooling

(Inch, Metric)

Item Number Min Bore Dia. Chip-breaker

Grade(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) ZM3

Regular type

SBG030050RB .118 3 .020 0.50 .118 3 50 9 1.3 2.7 0.8 .002 0.05 Yes ●SBG030075RB .118 3 .030 0.75 .118 3 50 9 1.3 2.7 0.8 .002 0.05 Yes ●SBG030100RB .118 3 .039 1.00 .118 3 50 9 1.3 2.7 0.8 .002 0.05 Yes ●SBG040050RB .157 4 .020 0.50 .157 4 60 12 1.8 3.6 1.0 .002 0.05 Yes ●SBG040075RB .157 4 .030 0.75 .157 4 60 12 1.8 3.6 1.0 .002 0.05 Yes ●SBG040100RB .157 4 .039 1.00 .157 4 60 12 1.8 3.6 1.0 .002 0.05 Yes ●SBG050050RB .197 5 .020 0.50 .197 5 70 20 2.3 4.5 1.2 .002 0.05 Yes ●SBG050100RB .197 5 .039 1.00 .197 5 70 20 2.3 4.5 1.2 .002 0.05 Yes ●SBG050150RB .197 5 .059 1.50 .197 5 70 20 2.3 4.5 1.2 .002 0.05 Yes ●SBG060100RB .236 6 .039 1.00 .236 6 80 20 2.8 5.4 1.8 .002 0.05 Yes ●SBG060150RB .236 6 .059 1.50 .236 6 80 20 2.8 5.4 1.8 .002 0.05 Yes ●SBG060200RB .236 6 .079 2.00 .236 6 80 20 2.8 5.4 1.8 .002 0.05 Yes ●SBG080100RB .315 8 .039 1.00 .315 8 80 20 3.8 7.3 2.2 .002 0.05 Yes ●SBG080150RB .315 8 .059 1.50 .315 8 80 20 3.8 7.3 2.2 .002 0.05 Yes ●SBG080200RB .315 8 .079 2.00 .315 8 80 20 3.8 7.3 2.2 .002 0.05 Yes ●

Short type

SBG030050RB-S .118 3 .020 0.50 .118 3 50 4.5 1.3 2.7 0.8 .002 0.05 Yes ○SBG030075RB-S .118 3 .030 0.75 .118 3 50 4.5 1.3 2.7 0.8 .002 0.05 Yes ○SBG030100RB-S .118 3 .039 1.00 .118 3 50 4.5 1.3 2.7 0.8 .002 0.05 Yes ○SBG030150RB-S .118 3 .059 1.50 .118 3 50 4.5 1.3 2.7 0.8 .002 0.05 Yes ○SBG040050RB-S .157 4 .020 0.50 .157 4 60 6 1.8 3.6 1.0 .002 0.05 Yes ○SBG040075RB-S .157 4 .030 0.75 .157 4 60 6 1.8 3.6 1.0 .002 0.05 Yes ○SBG040100RB-S .157 4 .039 1.00 .157 4 60 6 1.8 3.6 1.0 .002 0.05 Yes ○SBG040150RB-S .157 4 .059 1.50 .157 4 60 6 1.8 3.6 1.0 .002 0.05 Yes ○SBG050050RB-S .197 5 .020 0.50 .197 5 70 7.5 2.3 4.5 1.2 .002 0.05 Yes ○SBG050100RB-S .197 5 .039 1.00 .197 5 70 7.5 2.3 4.5 1.2 .002 0.05 Yes ○SBG050150RB-S .197 5 .059 1.50 .197 5 70 7.5 2.3 4.5 1.2 .002 0.05 Yes ○SBG050200RB-S .197 5 .079 2.00 .197 5 70 7.5 2.3 4.5 1.2 .002 0.05 Yes ○SBG060100RB-S .236 6 .039 1.00 .236 6 80 7.5 2.8 5.4 1.8 .002 0.05 Yes ○SBG060150RB-S .236 6 .059 1.50 .236 6 80 7.5 2.8 5.4 1.8 .002 0.05 Yes ○SBG060200RB-S .236 6 .079 2.00 .236 6 80 7.5 2.8 5.4 1.8 .002 0.05 Yes ○SBG080100RB-S .315 8 .039 1.00 .315 8 80 8.5 3.8 7.3 2.2 .002 0.05 Yes ○SBG080150RB-S .315 8 .059 1.50 .315 8 80 8.5 3.8 7.3 2.2 .002 0.05 Yes ○SBG080200RB-S .315 8 .079 2.00 .315 8 80 8.5 3.8 7.3 2.2 .002 0.05 Yes ○

(Inch, Metric)

Item Number Min Bore Dia. Chip-breaker

Grade(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) TM4

SFG060R100B .236 6 .039 1.00 .236 6 80 16.0 2.8 5.4 1.5 .002 0.05 Yes ○SFG060R150B .236 6 .059 1.50 .236 6 80 16.0 2.8 5.4 2.5 .002 0.05 Yes ○SFG060R200B .236 6 .079 2.00 .236 6 80 16.0 2.8 5.4 3.0 .002 0.05 Yes ○SFG080R100B .315 8 .039 1.00 .315 8 80 16.0 3.8 7.3 1.5 .002 0.05 Yes ○SFG080R150B .315 8 .059 1.50 .315 8 80 16.0 3.8 7.3 2.5 .002 0.05 Yes ○SFG080R200B .315 8 .079 2.00 .315 8 80 16.0 3.8 7.3 3.0 .002 0.05 Yes ○SFG080R300B .315 8 .118 3.00 .315 8 80 16.0 3.8 7.3 3.0 .002 0.05 Yes ○

■SBG (for ID Grooving)Minimum Bore Diameter .118" (3.0㎜)

■SFG (for ID Face Grooving)Minimum Bore Diameter .236" (6.0㎜)

■Cutting Conditions ➡J18

2°2°

± .001

Regular Type

Short Type

± .001

●:Stock ○: 1-2 week delivery

[ ID

Too

ling ]

For Swiss-type Lathes

J101

(Inch, Metric)

Item NumberMin Bore Dia. Pitch range Grade

(Inch) (㎜) (Inch) (㎜) Pitch(㎜) TPI (㎜) (㎜) (㎜) (㎜) (㎜) (Inch) (㎜) ZM3SBT025M3R .098 2.5 .118 3.0 0.5 50 50 5.4 1.10 2.3 0.6 .002 Max Flat 0.05 Max Flat ●SBT030M4R .118 3.0 .118 3.0 0.5-0.8 36-32 50 7.5 1.30 2.7 0.8 .002 Max Flat 0.05 Max Flat ●SBT030M4RB .118 3.0 .118 3.0 0.5-0.8 36-32 50 7.5 1.30 2.7 0.8 .002 Max Flat 0.05 Max Flat ●SBT035M5RB .138 3.5 .138 3.5 0.5-1.0 32-24 60 8.5 1.55 3.2 1.0 .002 Max Flat 0.05 Max Flat ●SBT040M6RB .157 4.0 .157 4.0 0.75-1.25 28-20 60 10.5 1.80 3.6 1.2 R.002 R0.05 ●SBT050M8RB .197 5.0 .197 5.0 0.75-1.5 28-18 70 15.8 2.30 4.5 1.5 R.002 R0.05 ●SBT060M10RB .236 6.0 .236 6.0 0.75-1.75 24-16 80 18.4 2.80 5.4 1.8 R.002 R0.05 ●

■SBT (for ID Threading) / Minimum Bore Diameter .118" (3.0㎜)

■Cutting Conditions ➡J19

●Threading

For 600 - 1500 RPM  Recommended Depth of Cut (DOC) for Each Pass

Metric Thread Number of Pass

Pitch(㎜) Total DOC(㎜) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

0.5 0.3 0.06 0.05 0.05 0.04 0.04 0.03 0.02 0.01 ― ― ― ― ― ― ― ― ― ― ― ― ―0.7 0.43 0.06 0.06 0.06 0.05 0.05 0.05 0.04 0.03 0.02 0.01 ― ― ― ― ― ― ― ― ― ― ―0.75 0.46 0.06 0.06 0.06 0.05 0.05 0.04 0.04 0.04 0.03 0.02 0.01 ― ― ― ― ― ― ― ― ― ―0.8 0.49 0.06 0.06 0.06 0.05 0.05 0.04 0.04 0.04 0.03 0.03 0.02 0.01 ― ― ― ― ― ― ― ― ―1.0 0.62 0.07 0.07 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.04 0.03 0.03 0.02 0.01 ― ― ― ― ― ― ―1.25 0.76 0.07 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.05 0.05 0.04 0.03 0.03 0.02 0.01 ― ― ― ― ― ―1.5 0.92 0.07 0.07 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.05 0.05 0.05 0.04 0.04 0.03 0.03 0.02 0.01 ― ― ―1.75 1.09 0.07 0.07 0.07 0.07 0.07 0.07 0.06 0.06 0.06 0.06 0.06 0.05 0.05 0.05 0.05 0.04 0.04 0.03 0.03 0.02 0.01

UNF Thread Number of Pass

Pitch(TPI) Total DOC(inch) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

36 0.43 .002 .002 .002 .002 .002 .002 .001 .001 .0008 .0004 ― ― ― ― ― ― ― ― ―32 0.49 .002 .002 .002 .002 .002 .001 .001 .001 .001 .0008 .0004 ― ― ― ― ― ― ― ―28 0.56 .003 .002 .002 .002 .002 .002 .001 .001 .001 .001 .001 .0008 .0004 ― ― ― ― ― ―24 0.66 .003 .002 .002 .002 .002 .002 .002 .002 .001 .001 .001 .001 .0008 .0004 ― ― ― ― ―20 0.78 .003 .003 .003 .003 .002 .002 .002 .002 .002 .002 .001 .001 .001 .001 .0008 .0004 ― ― ―18 0.87 .003 .003 .003 .003 .003 .002 .002 .002 .002 .002 .002 .002 .001 .001 .001 .0008 .0004 ― ―16 0.98 .003 .003 .003 .003 .003 .003 .003 .002 .002 .002 .002 .002 .002 .001 .001 .001 .001 .0008 .0004

60°

For Tools with .118”- .154”(3-4㎜) Shank Diameter(Ds)

For Tools with .197”- .236”(5-6㎜) Shank Diameter(Ds)

gg

[ ID

Too

ling ]

For Swiss-type Lathes

J102

ID Tooling

(Metric, ㎜)

Item number Stockφ φ Dimensions (㎜) Clamp screw

Wrench(Inch) (㎜) (Inch) (㎜) φ ① ② ③

NBH02015H ○ .079 2.0 5/8 15 15 100 10 SS0406F SS0406F LW-2

NBH02515H ○ .098 2.5 5/8 15 15 100 10 SS0406F SS0406F LW-2

NBH03015H ○ .118 3.0 5/8 15 15 100 10 10 SS0404F SS0404F SS0404F LW-2

NBH03515H ○ .138 3.5 5/8 15 15 100 10 10 SS0404F SS0404F SS0404F LW-2

NBH04015H ○ .157 4.0 5/8 15 15 100 15 15 SS0404F SS0404F SS0404F LW-2

NBH04515H ○ .177 4.5 5/8 15 15 100 15 15 SS0404F SS0404F SS0404F LW-2

NBH05015H ○ .197 5.0 5/8 15 15 100 15 15 SS0404F SS0404F SS0404F LW-2

NBH06015H ○ .236 6.0 5/8 15 15 100 20 20 SS0404F SS0404F SS0404F LW-2

NBH08015H ○ .315 8.0 5/8 15 15 100 20 20 SS0403F SS0403F SS0403F LW-2

NBH02016H ○ .079 2.0 .630 16 15 15 100 10 SS0406F SS0406F LW-2

NBH02516H ○ .098 2.5 .630 16 15 15 100 10 SS0406F SS0406F LW-2

NBH03016H ○ .118 3.0 .630 16 15 15 100 10 10 SS0404F SS0404F SS0404F LW-2

NBH03516H ○ .138 3.5 .630 16 15 15 100 10 10 SS0404F SS0404F SS0404F LW-2

NBH04016H ○ .157 4.0 .630 16 15 15 100 15 15 SS0404F SS0404F SS0404F LW-2

NBH04516H ○ .177 4.5 .630 16 15 15 100 15 15 SS0404F SS0404F SS0404F LW-2

NBH05016H ○ .197 5.0 .630 16 15 15 100 15 15 SS0404F SS0404F SS0404F LW-2

NBH06016H ○ .236 6.0 .630 16 15 15 100 20 20 SS0404F SS0404F SS0404F LW-2

NBH07016H ○ .276 7.0 .630 16 15 15 100 20 20 SS0403F SS0404F SS0404F LW-2

NBH08016H ○ .315 8.0 .630 16 15 15 100 20 20 SS0403F SS0403F SS0403F LW-2

NBH02019K ○ .079 2.0 3/4 18 18 125 10 SS0408F SS0408F LW-2

NBH02519K ○ .098 2.5 3/4 18 18 125 10 SS0408F SS0408F LW-2

NBH03019K ○ .118 3.0 3/4 18 18 125 10 10 SS0406F SS0406F SS0406F LW-2

NBH03519K ○ .138 3.5 3/4 18 18 125 10 10 SS0406F SS0406F SS0406F LW-2

NBH04019K ○ .157 4.0 3/4 18 18 125 15 15 SS0406F SS0406F SS0406F LW-2

NBH04519K ○ .177 4.5 3/4 18 18 125 15 15 SS0406F SS0406F SS0406F LW-2

NBH05019K ○ .197 5.0 3/4 18 18 125 15 15 SS0406F SS0406F SS0406F LW-2

NBH06019K ○ .236 6.0 3/4 18 18 125 20 20 SS0406F SS0406F SS0406F LW-2

NBH07019K ○ .276 7.0 3/4 18 18 125 20 20 SS0404F SS0404F SS0404F LW-2

NBH08019K ○ .315 8.0 3/4 18 18 125 20 20 SS0404F SS0404F SS0404F LW-2

NBH10019K ○ .394 10.0 3/4 18 18 125 20 20 SS0403F SS0404F SS0404F LW-2

① ② ③

5

10

■NBH / Shank dimeter:φ5/8"(15.875㎜ ) to 3/4"(19.05㎜ )

●:Stock ○: 1-2 week delivery

[ ID

Too

ling ]

For Swiss-type Lathes

J103

(Metric, ㎜)

Item number Stock φ φ Dimensions (㎜) Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) φ ① ② ③NBH02020K ○ .079 2.0 .787 20 11 19 125 10 SS0404F SS0404F LW-2NBH02520K ○ .098 2.5 .787 20 11 19 125 10 SS0404F SS0404F LW-2NBH03020K ○ .118 3.0 .787 20 12 19 125 10 10 SS0404F SS0404F SS0406F LW-2NBH03520K ○ .138 3.5 .787 20 12 19 125 10 10 SS0404F SS0404F SS0406F LW-2NBH04020K ○ .157 4.0 .787 20 13 19 125 15 15 SS0404F SS0406F SS0406F LW-2NBH04520K ○ .177 4.5 .787 20 13 19 125 15 15 SS0404F SS0406F SS0406F LW-2NBH05020K ○ .197 5.0 .787 20 14 19 125 15 15 SS0404F SS0406F SS0406F LW-2NBH06020K ○ .236 6.0 .787 20 15 19 125 20 20 SS0404F SS0406F SS0406F LW-2NBH07020K ○ .276 7.0 .787 20 16 19 125 20 20 SS0404F SS0406F SS0406F LW-2NBH08020K ○ .315 8.0 .787 20 17 19 125 20 20 SS0404F SS0404F SS0404F LW-2NBH10020K ○ .394 10.0 .787 20 19 19 125 20 20 SS0404F SS0404F SS0404F LW-2NBH02022K ○ .079 2.0 .866 22 11 21 125 10 SS0404F SS0406F LW-2NBH02522K ○ .098 2.5 .866 22 11 21 125 10 SS0404F SS0406F LW-2NBH03022K ○ .118 3.0 .866 22 12 21 125 10 10 SS0404F SS0406F SS0408F LW-2NBH03522K ○ .138 3.5 .866 22 12 21 125 10 10 SS0404F SS0406F SS0406F LW-2NBH04022K ○ .157 4.0 .866 22 13 21 125 15 15 SS0404F SS0406F SS0406F LW-2NBH04522K ○ .177 4.5 .866 22 13 21 125 15 15 SS0404F SS0406F SS0406F LW-2NBH05022K ○ .197 5.0 .866 22 14 21 125 15 15 SS0404F SS0406F SS0406F LW-2NBH06022K ○ .236 6.0 .866 22 15 21 125 20 20 SS0404F SS0406F SS0406F LW-2NBH07022K ○ .276 7.0 .866 22 16 21 125 20 20 SS0404F SS0406F SS0406F LW-2NBH08022K ○ .315 8.0 .866 22 17 21 125 20 20 SS0404F SS0406F SS0406F LW-2NBH10022K ○ .394 10.0 .866 22 19 21 125 20 20 SS0404F SS0404F SS0404F LW-2NBH12022K ○ .472 12.0 .866 22 21 21 125 25 25 SS0404F SS0404F SS0404F LW-2NBH02023K ○ .079 2.0 .906 23 11 21 125 10 SS0404F SS0406F LW-2NBH02523K ○ .098 2.5 .906 23 11 21 125 10 SS0404F SS0406F LW-2NBH03023K ○ .118 3.0 .906 23 12 21 125 10 10 SS0404F SS0406F SS0408F LW-2NBH03523K ○ .138 3.5 .906 23 12 21 125 10 10 SS0404F SS0406F SS0406F LW-2NBH04023K ○ .157 4.0 .906 23 13 21 125 15 15 SS0404F SS0406F SS0406F LW-2NBH04523K ○ .177 4.5 .906 23 13 21 125 15 15 SS0404F SS0406F SS0406F LW-2NBH05023K ○ .197 5.0 .906 23 14 21 125 15 15 SS0404F SS0406F SS0406F LW-2NBH06023K ○ .236 6.0 .906 23 15 21 125 20 20 SS0404F SS0406F SS0406F LW-2NBH08023K ○ .315 8.0 .906 23 17 21 125 20 20 SS0404F SS0406F SS0406F LW-2NBH10023K ○ .394 10.0 .906 23 19 21 125 20 20 SS0404F SS0404F SS0404F LW-2NBH12023K ○ .472 12.0 .906 23 21 21 125 25 25 SS0404F SS0404F SS0404F LW-2NBH02025K-MET ○ .079 2.0 .984 25 11 24 125 10 SS0404F SS0406F LW-2NBH02525K-MET ○ .098 2.5 .984 25 11 24 125 10 SS0404F SS0406F LW-2NBH03025K-MET ○ .118 3.0 .984 25 12 24 125 10 10 SS0404F SS0406F SS0408F LW-2NBH03525K-MET ○ .138 3.5 .984 25 12 24 125 10 10 SS0404F SS0406F SS0408F LW-2NBH04025K-MET ○ .157 4.0 .984 25 13 24 125 15 15 SS0404F SS0408F SS0408F LW-2NBH04525K-MET ○ .177 4.5 .984 25 13 24 125 15 15 SS0404F SS0408F SS0408F LW-2NBH05025K-MET ○ .197 5.0 .984 25 14 24 125 15 15 SS0404F SS0408F SS0408F LW-2NBH06025K-MET ○ .236 6.0 .984 25 15 24 125 20 20 SS0404F SS0408F SS0408F LW-2NBH07025K-MET ○ .276 7.0 .984 25 16 24 125 20 20 SS0404F SS0408F SS0408F LW-2NBH08025K-MET ○ .315 8.0 .984 25 17 24 125 20 20 SS0404F SS0406F SS0406F LW-2NBH10025K-MET ○ .394 10.0 .984 25 19 24 125 20 20 SS0404F SS0406F SS0406F LW-2NBH12025K-MET ○ .472 12.0 .984 25 21 24 125 25 25 SS0404F SS0404F SS0404F LW-2NBH02025K ○ .079 2.0 1 11 24 125 10 SS0404F SS0406F LW-2NBH02525K ○ .098 2.5 1 11 24 125 10 SS0404F SS0406F LW-2NBH03025K ○ .118 3.0 1 12 24 125 10 10 SS0404F SS0406F SS0408F LW-2NBH03525K ○ .138 3.5 1 12 24 125 10 10 SS0404F SS0406F SS0408F LW-2NBH04025K ○ .157 4.0 1 13 24 125 15 15 SS0404F SS0408F SS0408F LW-2NBH04525K ○ .177 4.5 1 13 24 125 15 15 SS0404F SS0408F SS0408F LW-2NBH05025K ○ .197 5.0 1 14 24 125 15 15 SS0404F SS0408F SS0408F LW-2NBH06025K ○ .236 6.0 1 15 24 125 20 20 SS0404F SS0408F SS0408F LW-2NBH07025K ○ .276 7.0 1 16 24 125 20 20 SS0404F SS0408F SS0408F LW-2NBH08025K ○ .315 8.0 1 17 24 125 20 20 SS0404F SS0406F SS0406F LW-2NBH10025K ○ .394 10.0 1 19 24 125 20 20 SS0404F SS0406F SS0406F LW-2NBH12025K ○ .472 12.0 1 21 24 125 25 25 SS0404F SS0404F SS0404F LW-2

1020

5

① ② ③

■NBH / Shank dimeter:φ.787"(20㎜ ) to 1"(25.4㎜ )

[ ID

Too

ling ]

For Swiss-type Lathes

J104

ID Tooling

■LBMD-S

.472

(12.0)

.354(9.0)

.591(15.0)

.394

(10.0)

Max depth.049

(1.25)

.098

(2.5)

φ

95°

Max depth of cut

〔Min bore dia.〕

LBMD1730FLPB05S LBMD2035FLPB05S

LBMD1020FLPB05S LBMD1430FLPB05S

LBMD2335FLPB05S shown

■LBM .774(18.9)

.354(9.0)Max. depth

.472

(12.0)

.378

(9.6)

.049

(1.25)

.098

(2.5)

θ1

φ〔Min bore diameter〕

θ2

Max. depth

Max. depth

.394

(10.0)

.394

(10.0)

〈Min. bore diameter φ.079(2.0)〉

〈Min. bore diameter φ.039(1.0)〉

Long type

Short type

(Inch, Metric)Min. bore dia. φ Item number

Max.depthChipbreaker

Grade(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) VM1.039 1.0 LBMD 1020 FL PB05S .079 2.0 .002 0.05 Yes ○.055 1.4 LBMD 1430 FL PB05S .118 3.0 .002 0.05 Yes ●.067 1.7 LBMD 1730 FL PB05S .118 3.0 .002 0.05 Yes ○.079 2.0 LBMD 2035 FL PB05S .138 3.5 .002 0.05 Yes ○.091 2.3 LBMD 2335 FL PB05S .138 3.5 .002 0.05 Yes ○

(Inch, Metric)Min. bore dia. φ Item number

Max.depth1 2 Chipbreaker

Grade(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) VM1 ZM3.039 1.0 LBMD 1020 FL VB .079 2.0 95° 10° 0 0 Yes ●.039 1.0 LBMD 1020 FL PB05 .079 2.0 95° 10° .002 0.05 Yes ●.079 2.0 LBMD 2060 FL VB .236 6.0 95° 10° 0 0 Yes ●.079 2.0 LBMD 2060 FL PB05 .236 6.0 95° 10° .002 0.05 Yes ●.118 3.0 LBM 3080 FL VB .315 8.0 90° 2° 0 0 Yes ●.118 3.0 LBM 3080 FL PB05 .315 8.0 90° 2° .002 0.05 Yes ●.118 3.0 LBMC 3080 FL VB .315 8.0 95° 2° 0 0 Yes ○ ○.118 3.0 LBMC 3080 FL PB05 .315 8.0 95° 2° .002 0.05 Yes ○ ○

LBM Series - Inserts

Mirror finish

Mirror finish

●:Stock ○: 1-2 week delivery M: Mirror finish

M

M

M

M

M

M

M

M

MMMMM

[ ID

Too

ling ]

For Swiss-type Lathes

J105

LBM Series - Toolholders■LBMA / Minimum bore diameter φ.039"(1.0㎜)-φ.118"(3.0㎜)

AA

.591(15)

4.724(120)

.591(15)

4.724(120)

AA

■LBMA-S / Minimum bore diameter φ.039"(1.0㎜)-φ.091"(2.3㎜)

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

LBM(C)3080LBMD(E)2060LBMD1020.

LBMAR06-IN ● 3/8 3/8 3/8 0 0 LRIS-4 × 10PW CLR-15SLBMAR08-IN ● 1/2 1/2 1/2 0 0 LRIS-4 × 12PW CLR-15SLBMAR10-IN ● 5/8 5/8 5/8 0 0 LRIS-4 × 12PW CLR-15SLBMAR08 ● .315 8 .315 8 .846 21.5 0 0 LRIS-4 × 10 LLR-25SLBMAR12 ● .472 12 .472 12 .846 21.5 0 0 LRIS-4 × 12PW CLR-15S

LBMD-SLBMAR10S ○ .394 10 .394 10 .709 18 0 0 LRIS-4 × 10PW CLR-15S

LBMAR12S ○ .472 12 .472 12 .709 18 0 0 LRIS-4 × 12PW CLR-15S

■DS-LBMB

Note: DS-LBMBL holders take right hand inserts

(Inch, Metric)

Gage Insert Item number Stockφ

Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

LBMD-SLBM(C)3080LBME2060LBMD2060LBMD1020

DS-LBMBL14F ○ .551 14 .512 13 3.150 80 LRIS-4 × 10PW CLR-15SDS-LBMBL15H ○ 5/8 .591 15 3.937 100 LRIS-4 × 10PW CLR-15SDS-LBMBL16X ○ .630 16 .591 15 3.740 95 LRIS-4 × 10PW CLR-15SDS-LBMBL19 ● 3/4 .709 18 4.724 120 LRIS-4 × 10PW CLR-15SDS-LBMBL20 ● .787 20 .748 19 4.724 120 LRIS-4 × 10PW CLR-15SDS-LBMBL22 ● .866 22 .827 21 4.724 120 LRIS-4 × 10PW CLR-15SDS-LBMBL25-MET ○ .984 25 .945 24 4.724 120 LRIS-4 × 10PW CLR-15SDS-LBMBL25 ● 1 .945 24 5.906 150 LRIS-4 × 10PW CLR-15S

.394(10)

0.0

φd

A

LBM.3 : .250"(6.35㎜)LBM.1 / LBM.2 : .266"(6.75㎜)

[ ID

Too

ling ]

For Swiss-type Lathes

J106

ID Tooling

Bore diameter φ.197"(5.0㎜)~ Steel shank / Carbide shank

Gage Insert Item number* Stockφ Min. bore Dia.

φ φStd. corner radius

Shape Clamp screw Wrench

(㎜) (inch) (㎜ ) (㎜)(㎜)(㎜)(㎜)(㎜)(㎜)(㎜) (inch) (㎜)

MBL S06F-MBRD05-OH ● 6.0 .197 5.0 5.7 80 2.5 13.5 9 - 2.5 0°-13° .0059 0.15 Fig.1 LR-S-2×3.5 CLR-13S

MBL C045F-MBRD05-OH ● 4.5 .197 5.0 4.0 80 2.5 - 9 - 1.5 0°-13° .0059 0.15 Fig.2 LR-S-2×3.5 CLR-13S

MBL C06F-MBRD05-OH ● 6.0 .197 5.0 5.7 80 2.5 18 9 - 1.5 0°-13° .0059 0.15 Fig.3 LR-S-2×3.5 CLR-13S

F1 chipbreakers evacuates chips BACKWARD (S-STUC style shown)

Note: F1 chipbreaker evacuates chips BACKWARD

φ φ

φ

Fig.1

Steel shank(tapered type)

φ

φ φ

Carbide shank(tapered type)

φ

φ φ

Fig.2

Carbide shank(straight type)

10°

【Boring+Face】

Fig.3

.008.004.008

.016

.024

.031

.039

.002Feed

No mark

(IPR)

(Inch)

D.O.C

.008.004.008

.016

.024

.031

.039

.002Feed (IPR)

(Inch)

D.O.C

F1

*For F1 chipbreaker, right-hand inserts fit to right-hand toolholder

* "S" denotes steel shank, "C" denotes carbide shank

■MBRD

■MBL

Item NumberGrade

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) TM4 ZM3MBL

L-hand shown

MBL 005 FL .142 3.6 .039 1.0 .002 0.05 ● ○

MBL 015 FL .142 3.6 .039 1.0 .006 0.15 ● ●

MBL-F1

R-hand shown

MBL 005 FR F1 .142 3.6 .039 1.0 .002 0.05 ●

MBL 015 FR F1 .142 3.6 .039 1.0 .006 0.15 ●

●Right hand shown

MogulBar for 75 deg Diamond ("MBL" style)

●:Stock ○: 1-2 week delivery

[ ID

Too

ling ]

For Swiss-type Lathes

J107

MogulBar for 75 deg Diamond ("ERGP" style)

F1 chipbreakers evacuates chips BACKWARD (S-STUC style shown)

* "S" denotes steel shank, "C" denotes carbide shank

■SEXR

■ERGP

Bore diameter φ.236"(6.0㎜)~ Steel shank / Carbide shank

●Right hand shown

F1A2 R-handA2 L-hand

5/32"

(3.97)

1/16"(1.6)

.008.004.008

.016

.024

.031

.039

.002Feed (IPR)

(Inch)

D.O.C

.008.004.008

.016

.024

.031

.039

.002Feed (IPR)

(Inch)

D.O.C

.008.004.008

.016

.024

.031

.039

.002Feed (IPR)

(Inch)

D.O.C

【Boring+Face】f

φD

m

L1h

φdθ°

α°L3

L2

8°L4

φD

s

Steel shank(tapered type)

Fig.1

φ φφ

Carbide shank(straight type) Carbide shank(tapered type)

φ φ

φ

Fig.2 Fig.3

IC Thickness Grade

ERGP-A2 Item Number ISO Item Number (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) TM4 VM1 ZM3 XT3 C7X

L-hand shown

ERGP 52Y- F A2 ERGHT 30102 FR A2 5/32 3.97 1/16 1.6 .008 0.2 ⓁR ○ ○ ○ ○

ERGP 521- F A2 ERGHT 30104 FR A2 5/32 3.97 1/16 1.6 .016 0.4 R Ⓛ

HandIC Thickness Grade

ERGP-F1 Item Number ISO Item Number (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) TM4

R-hand shown

ERGP 5204 FR-- F1 ERGHT 30101 FR F1 R 5/32 3.97 1/16 1.6 .004 0.1 ●

ERGP 52Y- FR-- F1 ERGHT 30102 FR F1 R 5/32 3.97 1/16 1.6 .008 0.2 ●

ERGP 521- FR-- F1 ERGHT 30104 FR F1 R 5/32 3.97 1/16 1.6 .016 0.4 ●

*1 Applicable for low depth of cut with right-hand A2 chipbreaker*2 For F1 chipbreaker, R-hand inserts fit to R-hand toolholder

●Right hand shown

Note: F1 chipbreaker evacuates chips BACKWARD

Gage Insert Item number* Stockφ Min. bore Dia.

φ φStd. corner radius

Shape Clamp screw Wrench

(㎜) (inch) (㎜ ) (㎜)(㎜)(㎜)(㎜)(㎜)(㎜)(㎜) (inch) (㎜)

ERGP52.. S08G-SEXRRT3D06-OH ● 8.0 .236 6.0 7.7 90 3.0 15 15 10 3.0 0°- 13° .008 0.2 Fig.1 LR-S-2×3.7 CLR-13S

ERGP52.. C05G-SEXRRT3D06-OH ● 5.0 .236 6.0 4.0 90 3.0 - 11 10 1.5 0°- 13° .008 0.2 Fig.2 LR-S-2×3.7 CLR-13S

ERGP52.. C06G-SEXRRT3D06-OH ● 6.0 .236 6.0 5.7 90 3.0 20 11 10 1.5 0°- 13° .008 0.2 Fig.3 LR-S-2×3.7 CLR-13S

[ ID

Too

ling ]

For Swiss-type Lathes

J108

ID Tooling

Bore diameter .394"(10㎜)~ Steel shank / Carbide shank

Bore diameter φ.276"(7.0㎜)~ Steel shank / Carbide shank

fφD

m

L1

h

L4

L3

L2

θ°

α°

φD

s

φd

fφD

m

L1 hL3

5°L4

φD

s

θ° L2

α°

φd

5°

●Right hand shownFig.1 Fig.2

Steel shank Carbide shank

■SCLP

■SCLC

fφD

m

L1

h

L4

L3

L2

θ°

α°

φD

s

φd

fφD

m

L1

h

φd

L3

5°L4

φD

s

θ° L2

α°

5°

●Right hand shownFig.1 Fig.2

Steel shank Carbide shank

Gage Insert Item number*Stock φ Min. bore Dia.

φ φStd. corner radius

Shape Clamp screw Wrench

R (㎜) (inch) (㎜) (㎜)(㎜)(㎜)(㎜)(㎜)(㎜)(㎜) (inch) (㎜)

CP..62.. S06F-SCLPR04D07-OH ● 6.0 .276 7.0 5.75 80 3.5 14 17.0 12.0 2.5 + 5°- 9° .008 0.2 Fig.1 LR‒S‒2 × 3.7 CLR‒13S

CP..62.. S07G-SCLPR04D08-OH ● 7.0 .315 8.0 6.75 90 4.0 16 19.5 13.5 3.0 + 5°- 7° .008 0.2 Fig.1 LR‒S‒2 × 3.7 CLR‒13S

CP..21.5.. S08H-SCLPR06D10-OH ● 8.0 .394 10.0 7.7 100 5.0 20 22.0 16.0 3.0 + 5°- 10° .016 0.4 Fig.1 LR‒S‒2.5 × 6 CLR‒15S

CP..62.. C06H-SCLPR04D07-OH ● 6.0 .276 7.0 5.75 100 3.5 15.5 11.5 12.0 2.0 + 5°- 9° .008 0.2 Fig.2 LR‒S‒2 × 3.7 CLR‒13S

CP..62.. C07J-SCLPR04D08-OH ● 7.0 .315 8.0 6.75 110 4.0 17.5 13.0 13.5 2.0 + 5°- 7° .008 0.2 Fig.2 LR‒S‒2 × 3.7 CLR‒13S

CP..21.5.. C08K-SCLPR06D10-OH ● 8.0 .394 10.0 7.7 125 5.0 21.5 16.5 15.0 2.5 + 5°- 10° .016 0.4 Fig.2 LR‒S‒2.5 × 6 CLR‒15S

Gage Insert Item number*Stock φ Min. bore Dia.

φ φStd. corner radius

Shape Clamp screw Wrench

R (㎜) (inch) (㎜) (㎜)(㎜)(㎜)(㎜)(㎜)(㎜)(㎜) (inch) (㎜)

CC..21.5.. S08H‒SCLCR06D10‒OH ● 8.0 .394 10.0 7.7 100 5.0 20.0 22.0 16.0 3.0 0° - 13° .016 0.4 Fig.1 LRIS‒2.5 × 5 CLR‒15S

CC..21.5.. S10K‒SCLCR06D12‒OH ● 10.0 .472 12.0 9.6 125 6.0 24.0 27.5 20.0 3.5 0° - 11° .016 0.4 Fig.1 LRIS‒2.5 × 5 CLR‒15S

CC..21.5.. S12M‒SCLCR06D14‒OH ໐ 12.0 .551 14.0 11.5 150 7.0 28.0 32.5 23.0 4.0 0° - 9° .016 0.4 Fig.1 LRIS‒2.5 × 5 CLR‒15S

CC..32.5.. S16Q‒SCLCR09D18‒OH ໐ 16.0 .709 18.0 15.4 180 9.0 36.0 42.5 30.0 5.0 0° - 10° .016 0.4 Fig.1 LRIS‒4 × 8 LLR‒25S

CC..21.5.. C08K‒SCLCR06D10‒OH ● 8.0 .394 10.0 7.7 125 5.0 21.5 16.5 15.0 2.5 0° - 13° .016 0.4 Fig.2 LRIS‒2.5 × 5 CLR‒15S

CC..21.5.. C10M‒SCLCR06D12‒OH ● 10.0 .472 12.0 9.6 150 6.0 25.0 20.0 19.5 2.5 0° - 11° .016 0.4 Fig.2 LRIS‒2.5 × 5 CLR‒15S

CC..21.5.. C12M‒SCLCR06D14‒OH ○ 12.0 .551 14.0 11.5 150 7.0 29.0 23.5 22.5 3.0 0° - 9° .016 0.4 Fig.2 LRIS‒2.5 × 5 CLR‒15S

* "S" denotes steel shank, "C" denotes carbide shank

* "S" denotes steel shank, "C" denotes carbide shank

MogulBar (80° Diamond positive type)

Inserts ➡ E31

Inserts ➡ E27・E28・E29●:Stock ○: 1-2 week delivery

[ ID

Too

ling ]

For Swiss-type Lathes

J109

MogulBar (60° Triangle positive type)

Bore diameter φ.315"(8.0㎜)~ Steel shank / Carbide shank

Bore diameter φ.394"(10㎜)~ Carbide shank

■STUC(P)

■C-STZP(C)

GageInsert Item number*Stock φ Min. bore Dia.

φ φStd. corner radius

Shape Clamp screw Wrench

R (㎜) (inch) (㎜) (㎜)(㎜)(㎜)(㎜)(㎜)(㎜)(㎜) (inch) (㎜)

TC..52.. S07G-STUCR06D08-OH ● 7.0 .315 8.0 6.75 90 4.0 16 19.5 12.5 2.5 0° - 11° .008 0.2 Fig.3 LR‒S‒2 × 4.4 CLR‒13S

TP..73.. S08H-STUPR09D10-OH ● 8.0 .394 10.0 7.7 100 5.0 20 22.5 14.5 3.0 + 5°- 10° .016 0.4 Fig.3 LR‒S‒2.5 × 4.8 CLR‒15S

TP..22.. S10K-STUPR11D12-OH ● 10.0 .472 12.0 9.6 125 6.0 24 27.5 18.5 3.5 + 5°- 7.5° .016 0.4 Fig.3 LR‒S‒3 × 5.8 RLR‒20S

TP..22.. S12M-STUPR11D14-OH ○ 12.0 .551 14.0 11.5 150 7.0 28 32.5 22.0 4.0 + 5°- 5° .016 0.4 Fig.3 LR‒S‒3 × 5.8 RLR‒20S

TP..22.. S16Q-STUPR11D18-OH ○ 16.0 .709 18.0 15.4 180 9.0 32 42.5 28.5 5.0 + 5°- 3° .016 0.4 Fig.3 LR‒S‒3 × 5.8 RLR‒20S

TC..52.. C07J-STUCR06D08-OH ● 7.0 .315 8.0 6.75 110 4.0 17.5 13.0 12.5 2.0 0° - 11° .008 0.2 Fig.4 LR‒S‒2 × 4.4 CLR‒13S

TP..73.. C08K-STUPR09D10-OH ● 8.0 .394 10.0 7.7 125 5.0 21.5 16.5 14.5 2.5 + 5°- 10° .016 0.4 Fig.4 LR‒S‒2.5 × 4.8 CLR‒15S

TP..22.. C10M-STUPR11D12-OH ● 10.0 .472 12.0 9.6 150 6.0 25.0 20.0 17.5 2.5 + 5°- 7.5° .016 0.4 Fig.4 LR‒S‒3 × 5.8 RLR‒20S

TP..22.. C12M-STUPR11D14-OH ○ 12.0 .551 14.0 11.5 150 7.0 29.0 23.0 21.5 3.0 + 5°- 5° .016 0.4 Fig.4 LR‒S‒3 × 5.8 RLR‒20S

TP..20.. C16Q-STUP 11D18-OH ○ 16.0 .709 18.0 15.4 180 9.0 37.0 29.0 28.0 4.0 + 5°- 3° .016 0.4 Fig.4 LR‒S‒3 × 5.8 RLR‒20S

* "S" denotes steel shank, "C" denotes carbide shank

Insert Item number*Stock φ Min. bore Dia.

φMax. shoulder height

φStd. corner radius

Clamp screw Wrench

R (㎜) (inch) (㎜) (inch) (㎜) (㎜)(㎜)(㎜)(㎜)(㎜)(㎜)(㎜) (inch) (㎜)

TC..52.. C06H-STZCR06D10-OH ○ 6 .394 10 .098 2.5 5.75 100 5.5 10.5 6 6 2.0 0° -10° .008 0.2 LR-S-2 × 4 CLR-13S

TP..73.. C08K-STZPR09D12-OH ○ 8 .472 12 .118 3 7.7 125 7 13.5 8.5 8.3 2.5 +5° -10° .016 0.4 LR-S-2.5 × 4.8 CLR-15S

TP..73.. C10M-STZPR09D14-OH ○ 10 .551 14 .118 3 9.6 150 8 18.5 12 8.3 2.5 +5° -7° .118 0.4 LR-S-2.5 × 4.8 CLR-15S

TP..22.. C12M-STZPR11D175-OH ○ 12 .689 17.5 .177 4.5 11.5 150 10.5 22 14.5 9.6 3.0 +5° -5° .117 0.4 LR-S-3 × 5.8 RLR-20S

φD

s

fφD

m

L3

L4

L1

θ°

L2

α°

h

φd

φD

s

L1

fφD

m

L3

L4

α°

θ°

L2

3°φd

h

Fig.3 Fig.4

Steel shank Carbide shank

●Right hand shown

Inserts ➡ E43 / E47・E48

●Use right-hand inserts for machining backward Use left-hand inserts for machining forward

Inserts ➡ E43 / E47・E48

φ

φφ

NEW

[ ID

Too

ling ]

For Swiss-type Lathes

J110

ID Tooling

Blind hole due to bar stock Typical inserts flow chips forwardThen packed chips damage and break cutting edges

FG, F1 and F05 chipbreakers flow chips backward and prevent cuttting edges from breakingNote: Use right-hand inserts with FG, F1 and F05 chipbreakers for right-hand boring bars

■Boring on CNC Swiss-Type Lathes

Chipbreakers for Mogul Bar

Name Chipbreaker Geometry Features ER Style CC Style CP Style TC Style TP Style

AM3 ● Great combination of sharp edge and chip control

AM5 ● Provides both good cutting performance and chip control

AZ7 ● Excellent chip control at light feed and light depth of cut

CL● Double-positive geometry● Sharp edge and low tool pressure● Very wide chip control range

FG ● Evacuate chips BACKWARD at light depth of cut

ZR● Covers a wide range of depth of cut under high-speed and low-feed conditions

■ Molded Chipbreakers

Name Chipbreaker Geometry Features ER Style CC Style CP Style TC Style TP Style

A・A1● Tough cutting edge and good chip control● General-purpose ID chipbreaker

A2 ● Sharp cutting edge due to large rake angle

B1・B2・B3 ● Stable cutting in boring thanks to sharp and tough cutting edge

F05・F1● Exclusively designed for ID boring●Evacuate chips BACKWARD

K ● Superb chip control on finishing applications

KHG● Excellent chip control on finishing cuts● For super high-precision machining

S ● Sharp cutting edge with excellent chip control

U・U1 ● Sharp cutting edge prevents work materials from work hardening

■ Ground Chipbreakers

●:Stock ○: 1-2 week delivery

[ ID

Too

ling ]

For Swiss-type Lathes

J111

BG Series - Inserts

BG Series - Toolholders■S-BGR ■BG

Gage Insert Item numberStock Min. Bore Dia.

φGroove width

covered φClamp screw Wrench

R (Inch) (㎜) (Inch) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

GTG10S08H-BGR10D10 ○ .394 10 .020-.079 .315 8 .303 7.7 .309 7.85 4.724 120 .787 20 .197 5 LR-S-2.5×6.8 CLR-15SS10K-BGR10D12 ○ .472 12 .020-.079 .394 10 .378 9.6 .386 9.80 4.724 120 .984 25 .236 6 LR-S-2.5×6.8 CLR-15S

GTG14

BGR12-00S ○ .551 14 -.079 .472 12 .433 11 .453 11.5 7.087 180 1.181 30 .276 7 LR-S-3×7.8 RLR-20SBGR12-012S ○ .551 14 .057-.079 .472 12 .433 11 .453 11.5 7.087 180 1.181 30 .276 7 LR-S-3×7.8 RLR-20SBGR14-00S ○ .630 16 -.079 .551 14 .512 13 .531 13.5 7.087 180 1.378 35 .315 8 LR-S-3×7.8 RLR-20SBGR14-012S ○ .630 16 .057-.079 .551 14 .512 13 .531 13.5 7.087 180 1.378 35 .315 8 LR-S-3×7.8 RLR-20S

GTG20 BGR16 ○ .787 20 .059-.079 .630 16 .591 15 .610 15.5 7.874 200 1.575 40 .394 10 LR-S-3×7.8 RLR-20SBGR20 ○ .984 25 .059-.079 .787 20 .748 19 .768 19.5 7.874 200 1.575 40 .472 12 LR-S-3×7.8 RLR-20S

Screw on typeBore diameterφ.394"(10㎜)~ ID Grooving

Right-hand style shown

■GTGd (IC) Item number

Grade(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) TM4 ZM3 QM3 C7X

7/32" (5.56)

GTG10050FL005 0.020 0.50 .047 1.2 .002 0.05 ○GTG10065FL00 0.026 0.65 .047 1.2 .002 0.05 ○GTG10075FL005 0.030 0.75 .047 1.2 .002 0.05 ○GTG10100FL005 0.039 1.00 .047 1.2 .002 0.05 ○GTG10125L 0.049 1.25 .047 1.2 .008 0.20 ○GTG10150FL005 0.059 1.50 .047 1.2 .002 0.05 ○GTG10200FL005 0.079 2.00 .047 1.2 .002 0.05 ○GTG10200FL01 0.079 2.00 .047 1.2 .004 0.10 ○

5/16" (7.94)

GTG14100FL00 0.039 1.00 .087 2.2 .002 0.05 ○GTG14145L 0.057 1.45 .087 2.2 .008 0.20 ○GTG14150FL00 0.059 1.50 .087 2.2 .002 0.05 ○GTG14175L 0.069 1.75 .087 2.2 .008 0.20 ○GTG14200FL01 0.079 2.00 .087 2.2 .004 0.10 ○

3/8" (9.525)

GTG20150FL 0.059 1.50 .126 3.2 .008 0.20 ○GTG20175L 0.069 1.75 .126 3.2 .008 0.20 ○GTG20200L 0.079 2.00 .126 3.2 .008 0.20 ○GTG20200FL 0.079 2.00 .126 3.2 .008 0.20 ○

w

L

1/8"(3.18)

+.002"-0

d

Left-hand style shown

[ ID

Too

ling ]

For Swiss-type Lathes

J112

ID Tooling

(Inch)

Gage insert Item number Stock

Min.machining diaDimensions (Inch)

Clamp screw Wrench(Inch) (㎜)

TMN06 TGC10T06H161R ○ .315 8.0 .236 .217 3.937 .149 .512 LR-S-2 × 4.4

CLR-13STMN08 TGC10T08K162R ○ .394 10.0 .315 .276 4.921 .185 .668 LR-S-2 × 5.5

TMN09 TGC10T10M163R ○ .472 12.0 .394 .354 5.906 .236 .787 LRIS-2.2 × 6

TMN06 HN59Z-0028 ○ .315 8.0 .236 .217 3.937 .149 .512 LR-S-2 × 4.4

CLR-13STMN08 HN59Z-0029 ○ .394 10.0 .315 .276 4.921 .185 .668 LR-S-2 × 5.5

TMN09 HN59Z-0030 ○ .472 12.0 .394 .354 5.906 .236 .787 LRIS-2.2 × 6

■TMN

Item NumberDimensions (inch)

Recommended pitch for machining

Machinable pitch range

Grade

φ ZM3

TMN06FR03 .156 .061

.0012 .093 63-34 TPI

TMN08FR03 .187.093

TMN09FR03 .219 ○

φ

.093

.093

Toolholders for ID Threading■TGC  Bore diameter φ.315"(8㎜) ~ Carbide shank

●Right-hand type shown

10°

Dm

DS

●Right-hand type shown

■HN  Bore diameter φ.315"(8㎜) ~ Carbide shank

●Right-hand type shown

10°

Dm

DS

Inserts for ID Threading

[ ID

Too

ling ]

For Swiss-type Lathes

J113

Indexable End Mills

J

For Swiss-type Lathes

[ In

dexa

ble En

d Mill ]

J114

Indexable End Mill

REZ Series Indexable End Mills

Note① Inserts with center blade can be attached to non-single-blade indexable end mills. In this case, roughness of machined surface will be improved, but plunge cut operations cannot be performed.

② For ramping machining with the single blade endmills, please take the effective cutting edge length (4.0㎜ = .157") into consideration on setting machining programs.

Work MaterialSpeedSFM

Axial feedIPR

Traverse feedIPR

Depth of cutInch

Steel 260 - 400 - .001 - .002 - .118

Stainless Steel 130 - 200 - .0008 - .0015 - .079

【Recommended Cutting Conditions】

* Combination of single-blade type endmills and inserts with center blade is required

●Attach 20㎜ (.787") endmills in ER16 collet●Just change inserts to index. No need to make any adjustments●High quality surface finish as low as 1um (Rz) when wiper inserts are used●Corner radius as small as .002"●In addition to D cut, ramping machining can be performed*

Features

●:Stock ○: 1-2 week delivery

[ In

dexa

ble En

d Mill ]

For Swiss-type Lathes

J115

■ REZ Style End Mills

Item number Chipbreaker Center blade Wiper

Grade(Inch) (㎜) DT4 ZM3 TM4

CZH04005CFR-BL .008 0.2 Y Y N ○CZH0402CFR-BL .002 0.05 Y Y N ○CZH0402CFR-140 .008 0.2 N Y Y ○ ●CZH04005CFR-140 .002 0.05 N Y Y ○ ●CZH0402CFR-070 .008 0.2 N N N ○ ○CZH04005CFR-070 .002 0.05 N N N ○ ●CZH0502CFR-141 .008 0.2 N Y Y ○CZH05005CFR-141 .002 0.05 N Y Y ○

Fig. GageInsert Item number Stock φ φ Clamp Screw Wrench

(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

1 CZH04.. REZ080C1R212 ○ .315 8 .394 10 2.362 60 .472 12 FSI02-2.2 × 4.0 T-07CZH05.. REZ100C1R218 ○ .394 10 .394 10 2.953 75 .472 12 FSI02-2.2 × 4.3 T-07

2

CZH04.. REZ100B2R329 ○ .394 10 .197 5 1.575 40 .394 10 FSI02-2.2 × 4.3 T-07CZH04.. REZ100C2R133 ○ .394 10 .236 6 1.969 50 .472 12 FSI02-2.2 × 4.3 T-07CZH04.. REZ100C2R132 ○ .394 10 .276 7 1.969 50 .472 12 FSI02-2.2 × 4.3 T-07CZH04.. REZ100C2R141 ● .394 10 .394 10 1.969 50 .472 12 FSI02-2.2 × 4.3 T-07CZH04.. REZ120C2R141 ○ .472 12 .394 10 1.969 50 .472 12 FSI02-2.2 × 4.3 T-07CZH04.. REZ140C2R141 ○ .551 14 .394 10 1.969 50 .472 12 FSI02-2.2 × 4.3 T-07

3CZH04.. REZ150B3R330 ○ .591 15 .197 5 1.575 40 .394 10 FSI02-2.2 × 4.3 T-07CZH04.. REZ200M3R319 ○ .787 20 .276 7 1.969 50 .472 12 FSI02-2.2 × 4.3 T-07CZH04.. REZ200M3R320 ○ .787 20 .394 10 1.969 50 .472 12 FSI02-2.2 × 4.3 T-07

4 CZH04.. REZ200C3R403* ● .787 20 .394 10 1.969 50 .472 12 FSI02-2.2 × 4.3 T-07

Fig. 1 Fig. 2 Fig. 3 Fig. 4

Note: Length of blade is .209" (5.3㎜) without center blade, and .157” (4.0㎜) with center blade

* REZ200M3R320 with 5 deg relief to reduce tool pressure. See Fig. 4 for detail

.074(1.88)

.219(5.56)

.165(4.20)

(4.0)

(0.4)

87°

Wiper .016

With wiper & center blade

Center blade

With chipbreaker

.157 (Length of blade)

φφ

90°

φφ

90°

φφ

90°

φφ

90°

[ In

dexa

ble En

d Mill ]

For Swiss-type Lathes

MEMO

J117

NTK Unique Tooling

●Y-axis Toolholders …………… J118●DS / DS-ACH Toolholders …… J123●CSV Series ……………………… J130

●Wrench and Screw Information … J132

J

For Swiss-type Lathes

[ N

TK U

niqu

e To

oling ]

J118

NTK Unique Tooling

●Chip drops down to the bed of the machine due to gravity, and chip control problem is solved

●Front turning, grooving, and back turning operations can be perfomed by utilizing Y-axis control

●Eliminates chips from interfering with other tools

Features

NTK's Y-axis control toolholders are so innovative that the holders utilize tool change controls on gang tooling posts (Y-axis) for turning operationThe Y-axis control toolholders enable performing front turning, grooving, and back turning by controling Y-axis

Unique Conce

pt

Eliminate chip control problems

Y-axis Toolholders

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J119

To avoid interference, two Y-axis toolholders should not be installed next to each other

For tool change, determine a retract point based on the overhang of the Y-axis toolholder

*Machinable ODs with Y-GTTR type grooving toolholders are shown as an example (The dimensions apply to other Y-axis toolholders as well)

Y-axisHolder

OverhangTool Layout Situation

Overhang Amount (L)

.787(20㎜)

.866(22㎜)

.984(25㎜)

.787(20㎜)

.591(15)

.591(15)

.039Clearance Waiting point

.039D1

D2

D3

.787

(20)

L.787

(20)

D1Max machinable OD with Holder A

No limitation No limitation No limitation

D2Max machinable OD with Holder B

.512(13㎜)

.512(13㎜)

.512(13㎜)

D3Max machinable OD with Holder C

No limitation No limitation No limitation

.984(25㎜)

.591(15)

.591(15)

.079Clearance

.079Clearance

.038Clearance

.038Waiting Point

D1

D2

D3

.984

(25)

.984

(25)

LD1

Max machinable OD with Holder A1.496(38㎜)

2.283(58㎜) No limitation

D2Max machinable OD with Holder B

.587(14.9㎜)

.535(13.6㎜)

.512(13㎜)

D3Max machinable OD with Holder C

1.496(38㎜)

2.283(58㎜) No limitation

1.181(30㎜)

.591(15)

.591(15)

.079Clearance

.079ClearanceWaiting Point

.039

Clearance.039

D1

D2D3

1.181

(30)

1.181

(30)

L

D1Max machinable OD with Holder A

1.055(26.8㎜)

1.142(29㎜)

1.516(38.5㎜)

D2Max machinable OD with Holder B

.811(20.6㎜)

.705(17.9㎜)

.587(14.9㎜)

D3Max machinable OD with Holder C

1.299 (33㎜)1.055 (26.8㎜)for TBP style

1.457 (37㎜)1.142 (29㎜)for TBP style

2.028 (51.5㎜)1.516 (38.5㎜)for TBP style

① ② ③ ④

① ② ③ ④

① ② ③ ④

① ② ③ ④

Retract the tool station based on the cutting edge location on the Y-axis toolholder

Install a standard toolholder between the two Y-axis toolholders

●Example: Tool change from No.2 to No.4

Machinable OD Dimensions

Important Notes for Using Y-axis Toolholders

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J120

NTK Unique Tooling

55-deg. Diamond ("DC" Style)

●:Stock ○: 1-2 week delivery

■Y-SDJCR

■Y-SDNCN

.787(20)

93°

A

A

4.724 (120)

A A

90°62°30′

0.0

.827(21)

4.724(120)

Gang toolingpost

Feed direction

Feed direction

Gang toolingpost

Note: Y-SDJC holders do not work with left-hand inserts (such as DCGT-LS)

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

DC..21.5..TFD07..

Y-SDJCR062-IN ● 3/8 3/8 .984 25 0 LRIS-2.5 × 7 CLR-15SY-SDJCR082-IN ● 1/2 1/2 .984 25 0 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11..

Y-SDJCR083-IN ● 1/2 1/2 .984 25 0 LRIS-4 × 10 LLR-25SY-SDJCR103-IN ● 5/8 5/8 .984 25 0 LRIS-4 × 10 LLR-25S

DC..21.5..TFD07.. Y-SDJCR12-07L ○ .472 12 .472 12 1.181 30 0 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11.. Y-SDJCR12-11L ● .472 12 .630 16 1.181 30 0 LRIS-4 × 10 LLR-25S

DC..32.5..TFD11..

Y-SDJCR12-11SOH* ○ .472 12 .472 12 .787 20 ― LRIS-4 × 10 LLR-25SY-SDJCR16-11OH* ○ .630 16 .630 16 .984 25 ― LRIS-4 × 10 LLR-25S

*Comes with coolant through

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

DC..32.5.. Y-SDNCN083-IN ● 1/2 1/2 1/4 6.35 .984 25 LRIS-4 × 10 LLR-25S

DC..32.5..Y-SDNCN12-11S ○ .472 12 .472 12 .236 6.0 .787 20 LRIS-4 × 10 LLR-25S

Y-SDNCN16-11L ○ .630 16 .630 16 .315 8.0 1.181 30 LRIS-4 × 10 LLR-25S

93°

A A

0.0 4.724 (120)

■Y-SDJC-OHCoolant-through for high-pressure coolant

Inserts ➡ E32・E33・E34 / E23

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J121

35-deg. Diamond ("VC" Style)

Back Turning (TBP Style)

■Y-SVJCR

A A4.724

(120)

0.0

.787(20)

93°

(Inch)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

VC..22..Y-SVJCR062-IN ● 3/8 3/8 .787 20 LRIS-2.5 × 7 CLR-15SY-SVJCR082-IN ● 1/2 1/2 .787 20 LRIS-2.5 × 7 CLR-15SY-SVJCR102-IN ● 5/8 5/8 .984 25 LRIS-2.5 × 7 CLR-15S

■Y-TBPR, Y-CTPAR ■Y-TBPR-OH

138(3.5) 4.724(120)

0.0

.787(20)

Feed direcition

Gang tooling postRight-Hand style shown Right-Hand style shown

Note: Use right-hand inserts for Y-TBPR and Y-CTPAR holders

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBP..FR..

Y-TBPR06-IN ● 3/8 3/8 .984 25 LRIS-4 × 10PW CLR-15SY-TBPR08-IN ● 1/2 1/2 .984 25 LRIS-4 × 12PW CLR-15SY-TBPR10-IN ● 5/8 5/8 .984 25 LRIS-4 × 12PW CLR-15SY-TBPR12 ○ .472 12 .472 12 .984 25 LRIS-4 × 12PW CLR-15SY-TBPR12SOH ○ .472 12 .472 12 .787 20 LRIS-4 × 12PW CLR-15SY-TBPR16OH ○ .700 16 .700 16 .984 25 LRIS-4 × 12PW CLR-15S

Screw Accessible from both side Coolant-through, Screw accessible from both side.

3°0.0

2.756 (70)

(Inch)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBPA..FR.. Y-CTPAR08L-IN ● 1/2 1/2 1.181 30 LRIS-4 × 12PW CLR-15S

Inserts ➡ E49 / E26

Inserts ➡ J44

Inserts ➡ J46

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J122

NTK Unique Tooling

Grooving ("GTM" and "TMG" Style)

Grooving (GTPA Style)

●:Stock ○: 1-2 week delivery

■Y-GTTR ■Y-GTTR-OHMax. depth of cut: .079" (2.0㎜) Coolant through for high-pressure coolant

A

B B

A

0.0

0.0

.079

(2.0)

.787

(20)

4.724(120)

Max. grooving depth

B

A A

B

2.756 (70)

0.0

Right-Hand style shown

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TMG32..R..GTM..32..R..

Y-GTTR06-IN ● 3/8 3/8 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR08-IN ● 1/2 1/2 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR10-IN ● 5/8 5/8 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR10 ○ .394 10 .394 10 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR12 ○ .472 12 .472 12 .984 25 LR-S-4 × 10PW CLR-15S

Y-GTTR12SOH* ○ .472 12 .472 12 .787 20 LR-S-4 × 10PW CLR-15S

*Comes with coolant through

Feed direcition

Gang tooling post

Feed direcition

Gang tooling post

(Inch, Metric)

Gage Insert Item number Stock Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

GTPA

Y-GTPAR1216 ○ .472 12 .630 16 .787 20 LRIS-4 × 12PW CLR-15S

Y-GTPAR1216SOH* ○ .472 12 .630 16 .787 20 LRIS-4 × 12PW CLR-15S

Y-GTPAR1616OH* ○ .630 16 .630 16 .787 20 LRIS-4 × 12PW CLR-15S

*Comes with coolant through

■Y-GTPA

A

A

.004(0.1) 4.724

(120)

1.063

(27)

■Y-GTPA-OH

Y-GTPAR1216SOH

Coolant hole position

6

1612

6

AA

B

B

0.0

2.756(70)

.004(0.1)

Coolant through for high-pressure coolant

Right-Hand style shown

Inserts ➡ J66・J67・J68

Inserts ➡ J72

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J123

●More turning tools without any hassle

●Available for Front turning, Back turning, Grooving, Threading, Micro-boring, and interchangeable tooling

●Available shank size range: from .511"(14㎜) to 1"(25.4㎜)

Features

Are you satisfied with the number of tool positions in your machine? NTK DS type toolholder is useful when additional tool position are requiredFive types of tool are available: Front turning, Back turning, Grooving, Threading, and Small boring which fit into the machines' vacant drill sleevesDS Series toolholders can be used with both Swiss or non-Swiss type CNC lathes

Industry Proven Co

ncept

For making the most of vacant drill sleeves

DS Toolholders

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J124

NTK Unique Tooling

●:Stock ○: 1-2 week delivery

80-deg. Diamond ("CC" Style)

■DS-SCLL-ACH95°

φ

Left-Hand style shown

Left-Hand style shown

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CC..32.5..

DS-SCLL16F-09-ACH ● .630 16.00 .610 15.5 3.150 80 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL19-09-ACH ● 3/4 .709 18.0 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL20-09-ACH ● .787 20.00 .748 19.0 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL22-09-ACH ● .866 22.00 .827 21.0 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL25-09-ACH ● 1 .945 24.0 5.906 150 .236 6.0 LRIS-4 × 8 LLR-25S

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CC..21.5..

DS-SCLL 15H-06 ○ 5/8 .591 15 3.937 100 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL 16F-06 ○ .630 16 .591 15 3.150 80 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL 19-06 ● 3/4 .709 18 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL 20X-06 ○ .787 20 .748 19 3.740 95 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL 20-06 ● .787 20 .748 19 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL 22-06 ● .866 22 .827 21 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SCLL 25-06 ● 1 .945 24 5.906 150 .236 6.0 LRIS-2.5 × 7 CLR-15S

CC..32.5..

DS-SCLL 15H-09 ○ 5/8 .591 15 3.937 100 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL 16F-09 ○ .630 16 .591 15 3.150 80 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL 19-09 ● 3/4 .709 18 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL 19-09-004* ● 3/4 .709 18 4.724 120 .413 10.5 LRIS-4 × 8 LLR-25SDS-SCLL 20X-09 ○ .787 20 .748 19 3.740 95 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL 20-09 ● .787 20 .748 19 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL 22-09 ● .866 22 .827 21 4.724 120 .236 6.0 LRIS-4 × 8 LLR-25SDS-SCLL 22-09-005* ● .866 22 .827 21 4.724 120 .472 12.0 LRIS-4 × 8 LLR-25SDS-SCLL 25-09 ● 1 .945 24 5.906 150 .236 6.0 LRIS-4 × 8 LLR-25S

*Comes with coolant through

■DS-SCLL

0.0

A A

95°

.787

φ

(20)

0.0

AA

95°

5°1/8NPT

φ

Note: Use right-hand or neutral inserts for DS-SCLL bars

DS-SCLL19-09-004DS-SCLL22-09-005(Coolant through)

Adjustable centerline height

Inserts ➡ E27・E28・E29 / E22

DS Toolholders[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J125

55-deg. Diamond ("DC" Style)

■DS-SVXL

A A

99°

0.0

46°

φ Right-Hand style shown

Note: Use right-hand or neutral inserts for DS-SVXL bars

■DS-SDUL

A A

0.0

122°

φ

■DS-SDUL-ACH

Ajustable range

0 - +.008

Ajustable range

0 - +.008

1.181(30)

φ

122°■DS-SDXL22-11-006 (Coolant through)

1/8NPT

0.0

A A

119°

φ.787(20)

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

DC..21.5..TFD07..

DS-SDUL14F-07 ○ .551 14 .512 13 3.150 80 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL15H-07 ○ 5/8 .591 15 3.937 100 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL16F-07 ○ .630 16 .591 15 3.150 80 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL19-07 ● 3/4 .709 18 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL20-07 ● .787 20 .748 19 4.724* 120 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL20X-07 ● .787 20 .748 19 3.740 95 .236 6.0 LRIS-2.5 × 7 CLR-15SDS-SDUL22-07 ● .866 22 .827 21 4.724 120 .236 6.0 LRIS-2.5 × 7 CLR-15S

DC..32.5..TFD11..*

DS-SDUL16F-11-ACH ● .630 16 .610 15.5 3.150 80 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL19-11 ● 3/4 .709 18.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL19-11-ACH ● 3/4 .709 18.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL20-11 ● .787 20 .748 19.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL20X-11 ● .787 20 .748 19.0 3.740 95 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL20-11-ACH ● .787 20 .748 19.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL22-11 ● .866 22 .827 21.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL22-11-ACH ● .866 22 .827 21.0 4.724 120 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDXL22-11-006* ● .866 22 .827 21.0 4.724 120 .472 12.0 LRIS-4 × 10 LLR-25SDS-SDUL25-11 ● 1 .945 24.0 5.906 150 .394 10.0 LRIS-4 × 10 LLR-25SDS-SDUL25-11-ACH ● 1 .945 24.0 5.906 150 .394 10.0 LRIS-4 × 10 LLR-25S

* TFD11 inserts cannnot be used with DS-SDXL toolholders

Left-Hand style shown

Left-Hand style shown

Left-Hand style shown

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

VC..22

DS-SVXL15H-11 ○ 5/8 .591 15 3.937 100 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL16F-11 ● .630 16 .591 15 3.150 80 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL19-11 ● 3/4 .709 18 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL20-11 ● .787 20 .748 19 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL20Y-11 ○ .787 20 .748 19 3.740 95 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL22-11 ● .866 22 .827 21 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15SDS-SVXL25-11 ● 1 .945 24 5.906 150 .394 10 LRIS-2.5 × 7 CLR-15S

35-deg. Diamond ("VC" Style)

Adjustable centerline height

Inserts ➡ E32・E33・E34 / E23

Inserts ➡ E49 / E26

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J126

NTK Unique Tooling

●:Stock ○: 1-2 week delivery

35-deg. Diamond with 11 deg. relief ("VP" Style)

60-deg. Triangle ("TN" Style)

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

VP..22..

DS-SVVPN16-11-ACH ● .630 16 .610 15.5 4.724 120 .591 15 LRIS-2.5 × 7 CLR-15SDS-SVVPN19-11 ○ 3/4 .709 18.0 4.724 120 LRIS-2.5 × 7 CLR-15SDS-SVVPN19-11-ACH ● 3/4 .709 18.0 4.724 120 .709 18 LRIS-2.5 × 7 CLR-15SDS-SVVPN20-11-ACH ● .787 20 .748 19.0 4.724 120 .748 19 LRIS-2.5 × 7 CLR-15SDS-SVVPN22-11 ○ .866 22 .827 21.0 4.724 120 LRIS-2.5 × 7 CLR-15SDS-SVVPN22-11-ACH ● .866 22 .827 21.0 4.724 120 .827 21 LRIS-2.5 × 7 CLR-15SDS-SVVPN25-11-ACH ● 1 .945 24.0 5.906 150 .945 24 LRIS-2.5 × 7 CLR-15S

■DS-SVVPN

35°

0.0

A A72°30’

1.063(27) φ

■DS-SVVP-ACH

Adjstable range

0 - .008

72°30'

1.378 (35)

φ

Adjustable centerline height

1.496"

b

R.004"

10°

0~+.008"

0~+.008"

Adjustable

range

6° φ

(Inch, Metric)

Gage Insert Item number Stock φ Clamp pin Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TN..33..

DS-PTXL16-33-ACH ● .630 16.00 .610 15.5 .591 15 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL19-33 ○ 3/4 .709 18.0 .709 18 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL19-33-ACH ● 3/4 .709 18.0 .709 18 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL20-33 ○ .787 20.00 .748 19.0 .748 19 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL20-33-ACH ● .787 20.00 .748 19.0 .748 19 4.724 120 .433 11 LCL33N LCS33 LW-2DS-PTXL22-33 ○ .866 22.00 .827 21.0 .827 21 4.724 120 .472 12 LCL33N LCS33 LW-2DS-PTXL22-33-ACH ● .866 22.00 .827 21.0 .827 21 4.724 120 .472 12 LCL33N LCS33 LW-2DS-PTXL25M-33 ○ 1 .945 24.0 .945 24 5.906 150 .512 13 LCL33N LCS33 LW-2DS-PTXL25-33-ACH ● 1 .945 24.0 .945 24 5.906 150 .512 13 LCL33N LCS33 LW-2

Right-Hand style shown

■DS-PTX

A A6°

10°

6°0.0

φ

■DS-PTX-ACH Adjustable centerline height

Inserts ➡ E50

Inserts ➡ E44・E45 / E25

DS Toolholders[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J127

Back Turning ("TBP" Style)

Grooving ("GTM" and "TMG" Style)

■DS-TBP

(Inch, Metric)

Gage Insert Item number Stockφ

Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TBP..FR..DS-TBPL19 ● 3/4 .709 18 4.724 120 .433 11 LRIS-4 × 10 LLR-25SDS-TBPL20 ○ .787 20 .748 19 4.724 120 .433 11 LRIS-4 × 10 LLR-25SDS-TBPL25 ● 1 .945 24 5.906 150 .512 13 LRIS-4 × 10 LLR-25S

0.0

.138(3.5)

.217(5.5)

.591(15) φ

Left-Hand style shown

■DS-GTTLMax. depth of cut: .079" (2.0㎜)

Note: DS-GTTL holders take right-hand inserts

A A

φ

0.0

.079

(2.0) .787

(20)Max. grooving depth

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TMG32..R..GTM..32..R..

DS-GTTL16X ○ .630 16 .591 15 3.740 95 .236 6 LR-S-4 × 5.8 RLR-20S

DS-GTTL19 ● 3/4 .709 18 4.724 120 .236 6 LR-S-4 × 5.8 RLR-20S

DS-GTTL20 ○ .787 20 .748 19 4.724 120 .236 6 LR-S-4 × 5.8 RLR-20S

DS-GTTL22 ● .866 22 .827 21 4.724 120 .236 6 LR-S-4 × 5.8 RLR-20S

DS-GTTL25 ● 1 .945 24 4.724 120 .394 10 LR-S-4 × 5.8 RLR-20S

Inserts ➡ J44

Inserts ➡ J66・J67・J68

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J128

NTK Unique Tooling

(Inch, Metric)

Gage Insert Item number Stockφ

Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

LBMD-SLBM(C)3080LBME2060LBMD2060LBMD1020

DS-LBMBL14F ○ .551 14 .512 13 3.150 80 LRIS-4 × 10PW CLR-15SDS-LBMBL15H ○ 5/8 .591 15 3.937 100 LRIS-4 × 10PW CLR-15SDS-LBMBL16X ○ .630 16 .591 15 3.740 95 LRIS-4 × 10PW CLR-15SDS-LBMBL19 ● 3/4 .709 18 4.724 120 LRIS-4 × 10PW CLR-15SDS-LBMBL20 ● .787 20 .748 19 4.724 120 LRIS-4 × 10PW CLR-15SDS-LBMBL22 ● .866 22 .827 21 4.724 120 LRIS-4 × 10PW CLR-15SDS-LBMBL25-MET ○ .984 25 .945 24 4.724 120 LRIS-4 × 10PW CLR-15SDS-LBMBL25 ● 1 .945 24 5.906 150 LRIS-4 × 10PW CLR-15S

●:Stock ○: 1-2 week delivery

Threading ("TTP" Style)

Micro-Boring ("LBM" Style)■DS-LBMB

.394(10)

0.0

φd

A

Left-Hand shown

Note: DS-LBMBL holders take right hand insertsNote: Also available in 14㎜ , 25㎜ , 5/8" shanks(φ )

■DS-TTPL

.217(5.5)

0.0

.787(20)

φ

Left-Hand style shown

(Metric, ㎜)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

TTP55FR..TTP60FR..

DS-TTPL19 ● 3/4 .709 18 4.724 120 .394 10 LRIS-4 × 10 LLR-25S

DS-TTPL20 ● .787 20 .748 19 4.724 120 .394 10 LRIS-4 × 10 LLR-25S

DS-TTPL22 ● .866 22 .827 21 4.724 120 .394 10 LRIS-4 × 10 LLR-25S

DS-TTPL25 ● 1 .945 24 5.906 150 .394 10 LRIS-4 × 10 LLR-25S

DS Toolholders

Inserts ➡ J82

Inserts ➡ J104

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J129

φ22

(.866)

43 (1.69)10 (.39)

φ16 (.630)

58 (2.28)

23 (.91) 28 (1.10)

Interchangeable Tools ("CSV" Style)

■SS-DSU-SK

Item number StockSpare parts

ComentCap screw Wrench Set screw Wrench

SS-DSU-SK ● CS0515 LW-4 SS0506 LW-2.5

SS-DSU-L23 ● CS0515 LW-4 SS0506SS0515 LW-2.5 For DS-ACH Series

DS-Sleeve

70 (2.76)

Set screwWrench

Cap screwWrench55 (2.17)

10 (.39)

φ22

(.886)

φ16 (.630)35 (1.38)

28 (1.10)

■SS-DSU-L23For DS-ACH series

AA

.787(20)

4.724 (120)

0.0

1°

φ

■DS-CSVL (Takes right-hand inserts)

(Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11FR.. DS-CSVL15 ● 5/8 .591 15 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15S

Left-Hand style shown

Inserts ➡ J130

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J130

NTK Unique ToolingInterchangeable Tooling

CSV Series - Inserts All CSV series inserts have polished cutting edges.Mirror finish

Item number Chip-breaker

Max Depth of Cut Edge geometry(α×β°) DT4 VM1(Inch) (㎜) (Inch) (㎜) R L R L

CSVF11F V-M No ― ― .006 × 2° 0.15 × 2° ● ● ●CSVF11F VB Yes .118 3.00 .012 × 5° 0.30 × 5° ● ○CSVF11F VB-M Yes .118 3.00 .006 × 2° 0.15 × 2° ● ● ●

■CSVF - Front Turning

1/46.3

5

β°

30°

α

0.0

1/46.3

5

Toolholders for right-hand inserts CSVR.., DS-CSVL..Toolholders for left-hand inserts CSVL..

Note: All angles shown are obtained when insert is set on the holder All images in this page show right-hand inserts

■CSVG - Grooving Item number Width Max. Depth of Cut VM1(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L

CSVG11F V025 .010 0.25 .006 0.15 .020 0.50 0.0 ●CSVG11F V030 .012 0.30 .006 0.15 .020 0.50 0.0 ○CSVG11F V035 .014 0.35 .006 0.15 .020 0.50 0.0 ●CSVG11F V040 .016 0.40 .006 0.15 .020 0.50 0.0 ○CSVG11F V045 .018 0.45 .018 0.45 .039 1.00 0.0 ●CSVG11F V050 .020 0.50 .018 0.45 .039 1.00 0.0 ●CSVG11F V055 .022 0.55 .018 0.45 .039 1.00 0.0 ○CSVG11F V060 .024 0.60 .018 0.45 .039 1.00 0.0 ●CSVG11F V065 .026 0.65 .018 0.45 .039 1.00 0.0 ○CSVG11F V070 .028 0.70 .018 0.45 .039 1.00 0.0 ●CSVG11F V075 .030 0.75 .050 1.40 .079 2.00 0.0 ● ○CSVG11F V080 .031 0.80 .050 1.40 .079 2.00 0.0 ○CSVG11F V085 .033 0.85 .050 1.40 .079 2.00 0.0 ○CSVG11F V090 .035 0.90 .050 1.40 .079 2.00 0.0 ○CSVG11F V095 .037 0.95 .050 1.40 .079 2.00 0.0 ● ○CSVG11F V100 .039 1.00 .050 1.40 .079 2.00 0.0 ●CSVG11F V110 .043 1.10 .102 2.60 .118 3.00 0.0 ○CSVG11F V120 .047 1.20 .102 2.60 .118 3.00 0.0 ● ○CSVG11F V130 .051 1.30 .102 2.60 .118 3.00 0.0 ●CSVG11F V140 .055 1.40 .102 2.60 .118 3.00 0.0 ○CSVG11F V150 .059 1.50 .102 2.60 .118 3.00 0.0 ●

1/4"

(6.35)

w

L

+.001"

-0

Item number Chip- breaker Pitch range

VM1(Inch) (㎜) R L

CSVT11F P60-035A No 125 TPI ~ 51 TPI .001MAX 0.03MAX ● ●CSVT11F P60-035B No 125 TPI ~ 51 TPI .001MAX 0.03MAX ● ●

■CSVT - Threading.014±.001

(1.0)

.039

60°

1/4"

(6.35)

.014±.001

(1.0)

.039

60°

type A

type B

●:Stock ○: 1-2 week delivery M: Mirror finish

Item number Chip-breaker

Max. Cut-off Dia. Width VM1(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) R L

CSVC11F V06 No .118 3 .024 0.6 .079 2.0 0.0 ○CSVC11F V07 No .157 4 .028 0.7 .098 2.5 0.0 ● ●CSVC11F V08 No .157 4 .031 0.8 .098 2.5 0.0 ○ ○CSVC11F V10 No .197 5 .039 1.0 .118 3.0 0.0 ● ●CSVC11F V13 No .197 5 .051 1.3 .118 3.0 0.0 ○ ○CSVC11F VB06 Yes .118 3 .024 0.6 .079 2.0 0.0 ○CSVC11F VB07 Yes .157 4 .028 0.7 .098 2.5 0.0 ●CSVC11F VB08 Yes .157 4 .031 0.8 .098 2.5 0.0 ○CSVC11F VB10 Yes .197 5 .039 1.0 .118 3.0 0.0 ●CSVC11F VB13 Yes .197 5 .051 1.3 .118 3.0 0.0 ○

25°

W±.002"

1/4"

(6.35)

1/4"

(6.35)

■CSVC - Cut-off

M

M

M

M

Item number Chip- breaker

Edge geometry(α×β°) DT4 VM1(Inch) (㎜) (Inch) (㎜) R L R L

CSVB11F V-M No .039 1.00 .006 × 2° 0.15 × 2° ● ● ●CSVB11F VB-M Yes .039 1.00 .006 × 2° 0.15 × 2° ● ● ●

1/4

(6.35)

α

β°45°

0.00.98(2.5)

W±.002"

1/4

(6.35)

■CSVB - Back Turning

M

M

M

M

M

M

M

M

M

M

M

M

M

MMMMMMMMMMMMMMMMMMMMM

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J131

CSV Series - Toolholders

■CSV

■CSV -NC

■DS-CSVL (Takes right-hand inserts)

AA .7875.512 (140)(20)

.004

(0.1)

1°

AA 1°

.7874.724 (120)(20)

.004

(0.1)

AA

.787(20)

4.724 (120)

0.0

1°

φ

Right-hand style shown

Right-hand style shown

Left-hand style shown

DS-CSVL (Inch, Metric)

Gage Insert Item number Stock φ Clamp screw Wrench(Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11FR.. DS-CSVL15 ● 5/8 .591 15 4.724 120 .394 10 LRIS-2.5 × 7 CLR-15S

CSV -NC (Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..CSV 06-IN-NC ● ● 3/8 3/8 3/8 0 0 LRIS-2.5 × 7 CLR-15S

CSV 08-IN-NC ● ● 1/2 1/2 1/2 0 0 LRIS-2.5 × 7 CLR-15S

CSV (Inch, Metric)

Gage Insert Item numberStock

Clamp screw WrenchR L (Inch) (㎜) (Inch) (㎜) (Inch) (㎜) (Inch) (㎜)

CSV..11..

CSV 07 ● ● .295 7 .295 7 .295 7 .020 0.5 LRIS-2.5 × 7 CLR-15SCSV 08 ● ● .315 8 .315 8 .315 8 0 0 LRIS-2.5 × 7 CLR-15SCSV 10 ● ● .394 10 .394 10 .394 10 0 0 LRIS-2.5 × 7 CLR-15SCSV 12 ● .472 12 .472 12 .472 12 0 0 LRIS-2.5 × 7 CLR-15S

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J132

NTK Unique Tooling

Standard Items

Item Number Appearance

CLR-13S(FormerlyRLR-13S)

CLR-15S(FormerlyRLR-15S)

RLR-20S

LLR-25S

LLR-25S-20*65

LLR-28S

Optional Items〈LLR Type〉

Item Number Appearance

LLR-13S

LLR-15S

LLR-20S

〈Driver type wrench kits〉Item Number Contents

XX2815-04-13S XX2815-04 with HLR-25S(HLR-13S)

XX2815-04-15S XX2815-04 with HLR-25S(HLR-15S)

XX2815-04-20S XX2815-04 with HLR-25S(HLR-20S)

XX2815-04-25S XX2815-04 with HLR-25S(HLR-25S)

〈Driver type wrench for increased usability〉Item Number Magnetic Driver Handle

XX2815-04

Item Number Replaceable Bits

HLR-13S

HLR-15S

HLR-20S

HLR-25S

■ Spare Parts - Wrenches

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

J133

•Make sure that wrench tip and wrench hole are neither deformed nor stripped

•Apply wrench straight to screw hole

•Do not apply more torque than the recommended amount (as shown to the right)

Note: Wrenches and bits come in a pack of five Clamp screws come in a pack of ten

Recommended Tightening TorqueAttention: When tightening screws

Item Number Recommended Tightening Torque(lbs)CLRLLR 13SHLR

6.2 (0.7N・m)

CLRLLR 15SHLR

12.4 (1.4N・m)

RLRLLR 20SHLR

26.6 (3.0N・m)

LLR 25SHLR 44.3 (5.0N・m)

LLR 28SHLR 62.0 (7.0N・m)

Clamp Screw Dimension(㎜) Standard Wrench

Appearance Order Code Item Number a b c θ(°) Order Code Item Number

θ

a

b

c5704739 LR-S-2×3.5 M2×P0.4 3.1 3.5 82

5681994 CLR-13S5907704 LR-S-2×3.7 M2×P0.4 3.1 3.7 82

5907712 LR-S-2×4.4 M2×P0.4 3.1 4.4 82

5907720 LR-S-2×5.5 M2×P0.4 3.0 5.5 90

5907738 LR-S-2.5×4.8 M2.5×P0.45 3.6 4.8 82

5681978 CLR-15S5704747 LR-S-2.5×5.5 M2.5×P0.45 3.6 5.5 82

5907746 LR-S-2.5×6 M2.5×P0.45 3.5 6.0 90

θ

a

b

Accessible from front and back

c

5907753 LR-S-2.5×6.8 M2.5×P0.45 3.5 6.8 90

5773619 LR-S-3×5.8 M3×P0.5 4.1 5.8 90

5485164 RLR-20S

5907761 LR-S-3×6.2 M3×P0.5 5.2 6.2 82

5907779 LR-S-3×7.8 M3×P0.5 4.0 7.8 90

5907787 LR-S-4×5.8 M4×P0.7 5.8 6.0 82

5907795 LR-S-4×9 M4×P0.7 5.8 9.0 82

5116991 LR-S-4×10PW M4×P0.7 5.8 10.0 90 5681978 CLR-15S

θ

a

b

c

5534029 LRIS-2×6 M2×P0.4 2.6 6.0 605681994 CLR-13S

5907803 LRIS-2.2×6 M2.2×P0.45 3.15 6.0 60

5989181 LRIS-2.5×5 M2.5×P0.45 3.6 5.0 605681978 CLR-15S

5907811 LRIS-2.5×7 M2.5×P0.45 3.6 7.0 60

5907829 LRIS-3×6 M3×P0.5 4.0 6.0 605485164 RLR-20S

5428156 LRIS-3×8 M3×P0.5 4.2 8.0 60

5477328 LRIS-4×5 M4×P0.7 5.85 5.0 60

53649305794698

LLR-25SLLR-25S-20*65θ

a

b

c

Accessible from front and back

5907837 LRIS-4×6 M4×P0.7 5.85 6.0 60

5977566 LRIS-4×8 M4×P0.7 5.85 8.0 60

5907845 LRIS-4×10 M4×P0.7 5.85 10.0 60

5684105 LRIS-4×12 M4×P0.7 5.85 12.0 60

5907852 LRIS-5×10 M5×P0.8 7.0 9.5 60 5364948 LLR-28S

5116983 LRIS-4×10PW M4×P0.7 5.7 10.0 605681978 CLR-15S

5090576 LRIS-4×12PW M4×P0.7 5.7 12.0 60

■ Clamp Screws and Wrenches

[ N

TK U

niqu

e To

oling ]

For Swiss-type Lathes

MEMO

K1

Information

●Grade Comparison Chart ………… K2●Material Cross Reference Chart … K4● Aerospace Material Specifications … K6● Hardness Comparison Chart … K12

K

Infomation

K2

Technical Data■ Grade Comparison Chart

NTK GREENLEAF HERTEL INDEXABLE ISCAR KENNAMETAL KYOCERA NEWCOMER ROMAY SANDVIK SPK SSANGYONG SUMIOTOMO TAEGUTECH TUNGALOY VALENITE

Cas

t iron

HC1HW2 GEM19 AC5 I50 IN11 KA30 NP5200 CC10 SZ200

SZ300AW20AB120

HC2HC5HC6

GEM7 MC2 I100 IN22IN23

K090KY1615

A65A66NPT600M

NP5000 CC20CC30

CC620CC650 SH2

ST100ST300ST500SD200TC300TA300

NB90S AB30LX11LX21CX710

Q32

SX1SX6SP2SP9

CSN100CSN200

MW30MW43

IS8IS80

KYK25KYK35KY3000KY3400KY3500

CS7050KS6000KS6050

CC510 CC513CC514CC514SCCC516CC516SC

CC6190CC1690

SL506SL508SL554CSL808SL550CSL654SL854C

SN26SN300SN400SN600SN500SN600SN700SN800

SN2000KSN2100KNS260NS260C

AS10SC10AS500

FX105 VPQ130VPQ135

Heat re

sistant

alloy S WA1 WG300

WG600 IW7 KY4300 CC600 CC670SW400SW500SW700

WX2000 TC430

SX5SX7SX9

MW37

KYS25KYS30KY2100KY1525KY1540

CF1 CC5477 CC6060CC6065 SN900 AS20

Harden

ed

material

H HC4ZC4HC7ZC7

GEN7 I100 IN22 KY4400A65KT66A66NPT600M

CC30SC CC6050 NB90S AB20 LX11Q35

VPZ215VPZ205

WA1 WG300WG600 IW7 KYS25

KY4300 CC670SW400SW500SW700

● Ceramics

● CBNNTK DIJET HITACHI INDEXABLE ISCAR KENNAMETAL KYOCERA MITSUBISHI SANDVIK SECO SPK SSANGYONG SUMIOTOMO TAEGUTECH TUNGALOY WALTER

Cas

t iron

B23B30

JBN795JBN330

BH200BH250

CBN90CBN95CBN100

IB50IB85IB55

KB5630KB1630KB1345KB9610KB9640

KBN60MKBN900

MB710MB5015MB730MBS140BC5030

CB7525CB7925

CBN050CCBN300PCBN20CBN200CBN300CBN350

WBN115WBN105WBN100WBN120WBN750

SBN1600BN700BNS800BN600BN500

TB650KB90KB90A

BX930BX90SBX870BX470BX480BX950BXC90

Harden

ed m

aterial

B52B36B40

JBN300JBN245

BH200BH250

CBN45CBN50CBN60CBN70

IB50IB55

KB1610KB1625KB5610KB1340KB5625KB9610KB9640

KBN510KBN525KBN10CKBN25CKBN05MKBN10MKBN25MKBN30MKBN35NKBN900

MBC010MB810BC8020MB8025MB825MB835

CB7015CB20CB50CB7025CB7525

CBN050CCBN10CBN100CBN150CBN170CBN200CBN160PCBN350CBN300P

SBN2000

BNX10BNX20BN250BNX25BN300BNC150BNC80DBNC200BNC300

KB50TB650

BX310BXM10BX330BX360BXC50BX530BX380BXM20

WLB30WLB50

* Italic type = Coated insert

● CermetNTK DIJET HITACHI ISCAR KENNAMETAL KYOCERA MITSUBISHI SANDVIK SECO SSANGYONG SUMIOTOMO TAEGUTECH TUNGALOY

Stee

l P XT3

Q15C7XC7ZXN4

LN10CX50CX75CX90CX99NITNATSUZ

CH350CZ25CH550CH7030CZ1025

IC20NIC520NIC530NIC75TIC30N

KT315KTP10

TN30PV30TN6010PV7010TN60TN6020PV7020PV7025TN90

AP25NNX2525NX3035VP45N

CT5015GC1525

CMC15M

TX510TX515TX520TX530

T110AT1200AT2000ZT3000Z

PV3010PV3030CT3000CT5000

NS520GT530GT730NS730NS740

Stain

less s

teel

XT3Q15C7XC7ZXN4

LN10CX50CX75CX90CX99NITNATSUZ

CH350CH550CH7030CZ1025

IC20NIC520NIC530NIC30N

KT315KTP10

TN60TN6020PV7020PV7025TN90

NX2525AP25NNX3035

GC1525 CMC15M

TX510TX515TX520TX530

T2000ZPV3010PV3030CT3000CT5000

NS520NS530GT730NS740

Cas

t iron

T15Q15

LN10NIT CH350 KT315

KTP10

TN30PV30PV7005TN60TN6010PV7005PV7010

AP25NNX2525 CT5015

TX510TX515TX520TX530

T110AT1200A

PV3010PV3030CT3000CT5000

NS520NS530NS730GT730

Infomation

K3

● Non coated carbideNTK DIJET GREENLEAF HITACHI INDEXABLE ISCAR KENNAMETAL KYOCERA MITSUBISHI ROMAY SANDVIK SECO SUMIOTOMO TAEGUTECH TUNGALOY WALTER

Stee

l P

KM1SRTDX30DX35SR30

G60G20M

WS10EX35EX40EX45

CI9CI7CI6CI5

IC70IC50MIC54

KU10 PW30 UTi20TS10MS25MS60M

ST10PST20EST30EA30

CT3000 UX30TX40

Cas

t iron

KM1

KG03KG1KG10KT9CR1KG20KG30LF12

G02WH02WH05WH10WH20D

CI65CI2CI3CI1CI4

IC04IC20IC10IC28

K68K313

KW10GW15GW25

HTi05THTi10TUTi20T

R600 H10H13A

890883HX

G10E UF1

TH03KS05FG1FTH10G2G2FKS15FKS20G3

WSN10WK1

● PVD coated carbideNTK DIJET GREENLEAF HITACHI INDEXABLE ISCAR KENNAMETAL KYOCERA MITSUBISHI SANDVIK SECO SUMIOTOMO TAEGUTECH TUNGALOY WALTER

Stee

l P

VM1ZM3QM3TM4DT4DM4

JC5003JC5030JC5015JC5040

G915G920G925

CY15CY150IP2000CY250CY9020HC844IP3000

CI29CI25A

IC507IC807IC907IC908IC328IC928IC3028

KC5510KC5010KCU10KCU25KC5025KC5525

PR915PR1005PR930PR1025PR1115PR1215PR1225

VP10MFVP10RTVP15TFVP20MFVP20RT

GC1125GC1525

CP200CP250CP500

ACZ150ACZ310AC520UACZ330ACZ350AC530U

TT1040TT7220TT8010TT8020TT9030TT9080

AH710AH725AH730SH730GH330AH120AH740AH130GH130AH140

WSM30WXP43WXM33WXP20

Stainles

s stee

l M

VM1ZM3QM3TM4DT4DM4

JC5003JC5015JC5030JC5040

G915G920G925

IP050SIP100SCY250CY9020

CI29CI24CI23

IC507IC520IC907IC308IC908IC3028IC1008IC1028IC3028IC928

KCU10KCU25KC5010KC5025KC5510KC5525

PR915PR1025PR1215PR1225PR930PR1125

VP10MFVP10RTVP15TFVP20MFVP20RT

GC15GC1005GC1105GC1115GC1525GC2035

TS2000CP200TS2500CP500

EH510ZACZ150AC510UEH520ZACZ310AC520UACZ330ACZ350AC530U

TT1040TT5080TT7010TT7080TT7220TT8010TT8020

AH710AH725AH730GH330SH730GH730AH120AH130GH130AH140

WXN10WXP43WXM33WXP20WXM20

Cas

t iron

QM3DM4

JC5003JC5015

CY100HCY10HCY9020

IC910IC507IC908IC508

KCU10KCU25KC5010KC5025KC5510KC5525

PR905PR1215

VP10RTVP15TFVP20RT

TS2000CP200DTS2500CP250CP500

EH10ZEH510ZAC510UEH20ZACZ310AC520UAC530U

TT1040TT6080TT7010TT7080

AH110GH110AH120GH130

● CVD coated carbideNTK DIJET GREENLEAF HITACHI INDEXABLE ISCAR KENNAMETAL KYOCERA MITSUBISHI ROMAY SANDVIK SECO SUMIOTOMO TAEGUTECH TUNGALOY WALTER

Cas

t iron

CP1

JC105VJC605XJC605WJC050WJC110VJC610JC215V

GA5022GA5023

HG3305HG3315HX3505HX3515GM8015HG8010GM8020GM8025GM25

CIN2CIT3CIT6CINXCIX

IC428IC9007IC9150IC418IC428IC9015IC9007

KCP05KCK05KCP10KCK15KCP25KCK20KCP30

CA4010CA4505CA5505CA4115CA4515 CA4120

UC5105UC5115UC6110UE6110

R100R200R500

GC3005GC3205 GC3210GC3215GC4215

TK1000TH1000TK2000MK1500TX150TP200TP2500

AC300GAC410KAC700GACK200DAC820PAC420KACK200

TT6300TT6800TT7005TT7015

T5105T5115T1115T5125

WPP01WPP10WPP20

● PCD

(Note) This chart is based on published data and not authorized by each manufacturer

NTK DIJET INDEXABLE ISCAR KENNAMETAL KYOCERA MITSUBISHI SANDVIK SECO SSANGYONG SUMIOTOMO TAEGUTECH TUNGALOY WALTER

Non-f

errou

sma

terial N

PD1

JDA30JDA735JDA40JDA745JDA10JDA715

PCD3PCD-FPCD-UF

ID5KD1400KD1405KD1425

KPD001KPD010 KPD230

MD205MD220MD230

CD10PD10PD20PD30

SPD100SPD200SPD300

DA1000DA2200DA150DA200DA90

KP100KP300KP500

DX180DX160DX140DX110DX120

WCD10 Infomation

K4

Technical Data

ISOCountry U.S.A. Japan Germany

ISOCountry U.S.A. Japan Germany

Standard AISI / SAE JIS DIN Standard AISI / SAE JIS DIN

Stainles

s stee

l M

Stainless Steel (Ferrite/Martensitic)

Cas

t iron

Malleable cast iron403 SUS403 X6Cr13 - FCMB310 -

X7Cr14 32510 FCMW330 EN-GJMB350-10416 SUS416 X12CrS13 40010 FCMW370 EN-GJMB450-6430 SUS430 X6Cr17 50005 FCMW490 EN-GJMB550-4410 SUS410 X10Cr13 70003 FCMP540

SUS420J2 X46Cr13 A220-70003 FCMP590 EN-GJMB650-2405 X6CrAL13 A220-80002 FCMP690 EN-GJMB700-2420 X20Cr13 Gray cast iron431 SUS431 X19CrNi17-2 No 20 B FC100 EN-GJL-100430F SUS430F X14CrMoS17 No 25 B FC150 EN-GJL-150434 SUS434 X6CrMoS17-2 No 30 B FC200 EN-GJL-200CA6- SCS5 X3CrNiMo13-4 No 35 B FD250 EN-GJL-250405 SUS405 X10CrAL13 No 40 B - -HNV6 SUH4 X85CrMoV18-2 No 45 B FC300 EN-GJL-300446 SUH446 X10CrAL2-4 No 50 B FC350 EN-GJL-350EV8 SUH35,SUH36 X53CrMnNiN21-9 No 55 B - EN-JLZS44400 X1CrMoTi18-2 A436 Type 2 - GGL-NiCr20-2

X20CrMoV12-1 Ductile cast iron630 X5CrNiCuNb16-4 60-40-18 FCD400 EN-GJL-400-15

Stainless Steel (Austenitic) - - EN-GJL-400-18-LT304L X2CrNi19-11 80-55-06 FCD500 EN-GJL-500-7304 SUS304 X5CrNi18-10 A43D2 - EN-GJSA-500303 SUS303 X8CrNiS18-9 - FCD600 EN-GJS-600-3

SUS304L 100-70-03 FCD700 EN-GJS-700-2304L SCS19 X2CrNi19-11

Nonferrous m

aterial

N SC64D C4BS G-AlSi9MGWA301 SUS301 X9CrNi18-8 GD-AISI12 AC4A G-ALMG5304LN SUS304LN X2CrNi18-10 356.1 A5052316 SUS316 X5CrNiMo17-2-2 A413.0 A6061 GD-AlSi12316LN SUS316LN X2CrNiMoN17-13-3 A380.1 A7075 GD-AlSi8Cu3316L X2CrNiMoN17-12-2 A413.1 ADC12 G-AlSi12(Cu)316L SCS16 X2CrNiMo18-14-3 A413.2 G-AlSi12

SUS316L A360.2 G-AlSi10Mg(Cu)317L SUS317L X2CrNiMo18-15-4

Heat-re

sistan

t allo

y S

Heat-resistant alloyUNS X1NiCrMoCu25-20-5 330 SUH330 X12NiCrSi36 16V 0890A SCH15 G-X40NiCrSi36-18321 SUS321 X6CrNiTi18-10 5390A347 SUS347 X10CrNiNb18-10 5666 NiCr22Mo9Nb316Ti X6CrNiMoTi17-12-2 NiCr20Ti318 X10CrNiMoNb 18-12 5660 NiFe35Cr14MoTi309 SUH309 X15CrNiSi20-12 5391 S-NiCr13A16MoNb310S SUH310 X8CrNi25-21 5383 NiCr19Fe19NbMo308 SCS17 X2CrNiMoN17-11-2 4676 NiCu30AL3Ti17-7PH X7CrNiAL 17-7 NiCr20TiAkN08028 X1NiCrMoCu31-27-4 AMS 5399 NiCr19Co11MoTi

Stainless Steel (Austenitic/Ferrite) AMS 5544 NiCr19Fe19NbMoS31500 X2CrNiN23-4 AMS 5397 NiCo15Cr10MoAlS32900 X8CrNiMo27-5 5537C CoCr20W15NiS32304 X2CrNiN23-4 AMS 5772 CoCr22W14NiS31803 X2CrNiMoN22-53 Titanium alloy

Harde

ned

materia

l

H 5130H SCr430H 34Cr4 AMS R54520 TiAl5Sn2.55135H SCr435H 37Cr4 AMS R56400 TiAl6V44135H SCM435H 34CrMo4 AMS R56401 TiAl6V4ELl4140H SCM440H 42CrMo4 TiAl4Mo4Sn4Si0.5

■ Material Cross Reference Chart

Heat resistant alloys for Aerospace ⇒ K6-K11

Infomation

K5

ISOCountry U.S.A. Japan Germany

ISOCountry U.S.A. Japan Germany

Standard AISI/SAE JIS DIN Standard AISI/SAE JIS DIN

Stee

l P

Carbon steel

Stee

l P

A573-81 SM400A;B;C S275J2G3A570.36 STKM12A;C S235JRG2 SM490A;B;C;YA;YB S355J2G3+C21115 GC16E 5120 DS355J2G3A573-8165 S235J2G3 9255 55Si71015 C15 9262 S340MGC1020 C22 52100 SUJ2 100Cr61213 SUM22 11SMn30 ASTM 16Mo312L13 SUM22L 11SMnPb30 4520 16Mo5

10SPb20 ASTM 14Ni61215 11SMn37 8620 SNCM220(H) 21NiCrMo212L14 11SMnPb37 8740 SNCM240 40NiCrMo221015 S15C Ck15E 17CrNiMo61025 S25C Ck25E 5015 SCr415(H) 15Cr3A572-60 S380N 5140 SCr440 42Cr4A572-60 17MnV7 5155 SUP9(A) 55Cr31035 C35 SCM415(H) 15CrMo51045 C45 8740 SNCM240 40NiCrMo8-41040 35S20 5015 SCr415(H) 15Cr31039 40Mn4 ASTMA182 13CrMo51335 SMn438(H) 36Mn5 ASTMA182 13CrMo4-51330 SCMn1 28Mn6 14MoV631035 S35C C35G 31CrMo121045 S45C C45E 39CrMoV131050 S50C C53G L1 41CrS41055 C55 8620 22Mo41060 C60E 50CoMo41055 S55C C55E 16MnCr51060 S58C C60E 31NiCrMo141095 C101E L6 50NiCr13W1 SK3 C101u 3135 SNC236 36NiCr6W210 SUP4 C105W1 3415 SNC415(H) 14NiCr10

Alloy steel 3415;3310 SNC815(H) 14NiCr14ASTMA353 X8Ni9 92552515 12Ni19 9840 36CrNiMo4

14NiCrMo13 4340 34CrNiMo65132 SCr430(H) 34Cr4

D3 SKD1 X210Cr12 5140 SCr440(H) 41Cr45115 16MnCr54130 SCM420;SCM430 25CrMo4

H13 SKD61 X40CrMo134 4137;4135 SCM432;SCCRM3 34CrMo44140;4142 SCM440 41CrMo4

A2 SKD12 X100CrMoV51 4140 SCM440(H) 42CrMo4SKD2 X210CrW12 32CrMo12

S1 45WCrV7 6150 SUP10 51CrV4H21 SKD5 X30WCrV93 41CrMo7

X30WCrV9 L3 100Cr6X165CrMoV12 SKS31 105WCr6

HW3 SUH1 X45GrSi93 SKS2,SKS3D3 SUH3 S6-5-2 L6 SKT4 55NiCrMoV6M2 SKH51 S6-5-2 Cast steel M35 SKH55 S6-5-2-5 SEMnH1M7 S6-9-2 SCMnH/1 G-X120Mn12HNV3 X210Cr12G

Infomation

K6

Technical Data

Commercialdesignation

HardnessBrinell HB

Nominal compositionApproximate content in %

Ann. Aged Ni Cr Co Fe Mo C Mn Si Al Ti Others

Astroloy* 56.9 15.0 15.0 5.25 0.06 4.0 3.5 0.05GMR 235* 63.3 15.5 10.0 5.2 0.15 0.25 0.6 3.0 2.0 0.06GMR 235D 63.0 15.5 4.5 5.0 0.15 0.1 0.3 3.5 2.5 0.05Hastalloy B* 140 64.3 0.6 1.25 5.5 28.0 0.1 0.8 0.7 Hastalloy C* 200 54.1 16.0 1.25 5.75 17.0 0.07 0.8 0.7 4.0Hastalloy N* 72.2 7.0 0.25 3.0 16.5 0.06 0.4 0.25 0.5 0.21Hastalloy W* 62.7 5.0 1.25 5.5 24.5 0.06 0.5 0.5 Hastalloy X* 160 47.1 22.0 1.5 18.5 9.0 0.1 0.6 0.6 0.6Hastelloy R235* 61.0 15.0 2.5 10.0 5.5 0.15 0.25 0.6 3.0 2.0 Haynes 75 73.7 20.0 5.0 0.12 0.25 0.4 0.5Haynes 80A 70.9 20.0 2.0 3.0 0.1 1.5 2.5 Haynes 263 25 51.4 20.0 20.0 6.0 0.06 1.0 1.5 Haynes 600 75.9 16.0 8.0 0.08 Haynes 625 61.4 21.0 5.0 9.0 0.1 3.5Haynes 718 43 53.5 18.0 19.0 3.0 0.08 0.5 0.9 5.0Haynes X-750 37 74.9 16.0 7.0 0.08 0.8 0.25 1.0IN-100* 61.6 10.0 15.0 3.0 0.18 1.2 0.5 5.5 4.75 Incoloy 804* 41.0 29.5 26.0 0.1 1.0 0.75 0.25 0.6 0.5Incoloy 825* 180 42.0 21.0 30.0 3.0 0.04 1.0 2.0Incoloy 901* 180 300 44.3 12.5 34.0 6.0 0.05 0.24 0.12 0.15 2.7 0.15Incoloy 903* 380 39.0 15.0 41.0 0.02 0.7 1.4 3.0Inconel 600* 170 75.0 15.5 8.0 0.05 Inconel 601* 150 60.0 23.0 14.0 0.05 1.4 Inconel 604* 180 74.4 15.8 7.2 0.04 0.2 0.2 0.1Inconel 625* 180 61.0 21.5 2.5 9.0 0.04 0.5 0.5 0.4 0.4 3.6Inconel 700* 350 46.0 15.0 23.5 0.7 3.75 0.12 0.1 0.3 3.0 2.2 Inconel 702* 79.6 15.6 0.35 0.04 0.05 0.2 3.0 0.7 Inconel 706* 42.0 16.0 40.0 0.03 0.2 0.3 0.4 1.75 Inconel 713* 75.0 12.5 4.2 0.12 6.1 0.8 Inconel 718* 180 380 52.5 19.0 19.0 3.0 0.04 0.35 0.35 0.9 0.9 0.1Inconel 722* 380 74.8 15.0 6.5 0.04 0.55 0.2 0.6 2.4 Inconel 751* 70.0 15.5 7.0 0.1 1.0 0.5 1.5 2.6 0.5Inconel 781 70.0 16.0 8.0 0.07 2.25 0.15 0.1 3.0 0.2Inconel X-750* 390 73.0 15.5 7.0 0.04 0.35 0.35 0.7 2.5 Jessop G39* 130 67.5 19.5 5.0 3.0 0.5 4.5Jessop G64* 220 60.7 11.0 2.0 3.0 0.15 6.0 4.0Jessop G81* 300 79.3 20.0 13.0 0.05 1.3 2.3 Jethete M-252* 320 55.3 20.0 10.0 10.0 0.15 0.5 0.5 1.0 2.6 MAR-M 200* 69.4 9.0 10.0 0.15 5.0 2.0 13.5MAR-M 246* 270 59.5 9.0 10.0 0.2 2.5 0.15 5.5 1.5 11.5MAR-M 421* 62.3 15.5 10.0 1.7 0.15 4.3 1.75 5.3MAR-M 432* 52.3 15.5 20.0 0.15 2.8 4.3 5.0Monel 400* 110 65.0 1.5 0.12 1.0 32.0Monel K-500* 120 290 64.0 1.0 0.13 0.8 2.8 0.6 30.0

● Material Specifications Cross-Reference List-Aerospace Material Designation■ Ni-based Heat Resistant Alloys

* These alloys can be hardened by an aging process

Infomation

K7

USA UK France Germany Others

SAE AMS BS AFNOR Werkst.-Nr DIN1706

AISI:686 NiCr16MoAl

5396A 5396 ND37FeV 2.48 S-NiMo30 N100015388C 5388 2.4602 NiCr17Mo17FeW N100025771 5607 N10003 5786 N10004

5390A 5390 NC22FeD 2.4603 N06002 5872 5596/5597 5542/5593 NC15TNbA 5397 LW2.4674 NiCo15Cr10MoAITi N13100 3072-76 NC21FeDU 2.4858 NiCr21Mo N08825 5660 ZSNCDT42 LW2.4662 NiFe35Cr14MoTi N09901 5540 5580 3072-76 NC15Fe 2.4816 NiCr15Fe N06600 5715 2.4851 NiCr23Fe N06601 5666 NC22FeDNB 2.4856 NiCr22Mo9Nb N06625 NK27CADT NiCo29Cr15MoAITi 5550 N07702 5702 N09707 5391 3146-3 NC12AD LW2.4670 S-NiCr13AI6MoNb 5383 5589 HR8 NC19FeNB LW24668 NiCr19Fe19NbMo N07713 5541 NC16FeTi NiCr16FeTi N07722 N07751

5542G 5582 NC16FeTNb 2.4669 NiCr16FeTi N07750 NiCr20MoW NiCr11AIWNb NiCr20Co18Ti 5551 2.4916 S-NiCr19Co N07252 NiW13Co10Cr9AITi 2.4675 NiCo10W10Cr9AITi NiCR16Co10WAlTi NiCo20Cr16WAITi 4544 4574 3072-76 NU30 2.436 NiCu30Fe N044004676 3072-76 2.4375 NiCu30AI N05500

Infomation

K8

Technical Data

* These alloys can be hardened by an aging process

Commercialdesignation

HardnessBrinell HB

Nominal compositionApproximate content in %

Ann. Aged Ni Cr Co Fe Mo C Mn Si Al Ti Others

Monel R-405* 110 66.0 1.2 0.15 1.0 31.06Nimocast 80* 69.9 20.0 2.0 5.0 0.1 1.0 2.0 Nimocast 90* 52.9 20.0 18.0 5.0 0.1 1.5 2.5 Nimocast 713 72.6 13.4 4.5 0.12 6.2 1.0 2.3Nimocast 842 57.7 22.0 10.0 10.0 0.3 Nimocast PD16 43.8 16.5 34.0 3.3 0.06 1.2 1.2 Nimocast PE10 56.4 20.0 6.0 9.0Nimocast PK24 61.1 9.5 15.0 3.0 0.17 5.5 4.7 1.0Nimonic 75* 170 75.0 19.5 4.0 0.12 0.4 Nimonic 80A* 350 75.0 19.5 0.08 1.4 2.4 Nimonic 90* 346 59.0 19.5 16.5 0.08 1.5 2.5 Nimonic 95 49.9 19.5 5.0 0.11 1.0 2.0 3.5 Nimonic 105* 320 53.0 15.0 20.0 5.0 0.12 4.7 1.2 Nimonic 115* 350 59.0 14.2 13.2 4.0 0.16 5.0 4.0 Nimonic 242 58.0 21.5 10.0 10.5 Nimonic 263/C263* 275 51.5 20.2 20.0 6.0 0.06 0.5 2.0 Nimonic 901* 350 44.0 12.5 35.0 5.7 0.04 0.3 2.9 Nimonic PE13 49.0 21.8 1.5 18.5 9.0 0.1 0.5 0.5 0.6Nimonic PE16* 250 43.5 16.5 34.0 3.3 0.06 1.2 1.2 Nimonic PK25 49.9 19.0 19.5 4.0 0.08 0.8 0.8 2.9 2.9 Nimonic PK31 53.8 20.0 14.0 4.5 0.4 2.3 5.0Nimonic PK33* 350 55.9 18.0 14.0 0.5 7.0 0.05 0.25 0.25 2.1 2.2 R-235* 63.3 15.0 1.2 10.0 5.5 0.12 0.1 0.3 2.0 2.5 Refractaloy 26 38.0 19.0 20.0 16.0 3.2 0.03 0.8 1.0 0.2 2.75 Rene 41 53.1 19.0 11.0 1.8 10.0 0.09 0.3 0.3 1.5 3.1 Rene 63 54.4 14.0 15.0 0.5 6.0 0.05 0.1 0.2 3.8 2.5 3.5Rene 77 57.6 15.0 15.0 0.4 4.2 0.17 0.1 0.1 4.3 3.3 Rene 80 61.0 14.0 9.5 4.0 0.15 4.0 8.0Rene 95 64.5 14.0 8.0 3.5 0.15 2.5 3.5Rene 100 60.6 10.0 15.0 3.0 0.18 5.5 4.7 Rene 125 60.0 8.9 10.0 2.0 0.1 4.7 2.5 7.0TRW 1800 70.0 13.0 0.1 6.0 0.06 10.5TRW V1 A 70.5 6.0 7.5 2.0 0.13 5.4 1.0 6.3Udimet 500* 51.7 19.0 19.0 4.0 0.1 0.1 0.1 3.0 3.0 Udimet 630 51.0 17.0 17.5 3.0 0.04 0.6 1.1 4.1Udimel 700 54.6 15.0 17.5 0.1 4.4 3.4 Udimet 710 55.0 18.0 15.0 0.5 1.5 0.07 2.5 5.0 1.5Udimet 718* 180 380 52.5 18.0 18.0 3.0 0.05 0.6 0.1 5.2Waspaloy* HRC35-42 56.9 19.8 13.5 0.8 4.45 0.07 0.1 0.1 1.4 3.0

● Material Specifications Cross-Reference List-Aerospace Material Designation■ Ni-based Heat Resistant Alloys

Infomation

K9

USA UK France Germany Others

SAE AMS BS AFNOR Werkst.-Nr DIN1706

4674 7234 N04405 3146

5391A HC203 NC13AD 2.467 S-NiCr13AI6MoNb 5397 HC204 NK15CAT LW2.4674 NiFe33Cr17Mo 3146 HR5,203-4 NC20T 2.463 NiCr20Ti Hr401,601 NC20TA 2.4631 NiCr20TiAk N07080 Hr2,202 Nc20ATV 2.4632 NiCr20Co18Ti N07090 HR3 NCKD20ATV 2.4634 NiCo20C15MoAITi HR4 NCK15ATD 2.4636 NiCo15Cr15MoAITi HR10 NCK20D 2.465 NiCr15Co19MoTi

5660C 5661A ZSNCDT42 2.4662 NiCr15MoTi 5536E 5754E HR6,204 NC22FeD 2.4665 NiCr22Fe18Mo HR207 NW11AC NiFe33Cr17Mo

5751A 5753 NKOD20ATU 2.4666 NiCr18CoMo NC19KDUV NiCr20Co16MoTi Z6NKCDT38 5399 NC19KDT 2.4973 NiCr19Co11MoTi N07041 NC14K8 NiCo15Cr10MoAITi NiTa9Co8W6CrAI 5751 NCK19DAT 2.4983 NiCr18Co18MoTi N07500 2.4668 NiCr19NbMo NCKD20AT 2.4636 NiCo15CrMoAlTi NC18TDA 5383 5589 HR8 NC19FeN LW2.4668 NiCr19Fe19NbMo N07718 5544 NC20K14 LW2.4668 NiCr19Fe19NbMo N07001 In

fomation

K10

Technical Data

* These alloys can be hardened by an aging process

Commercialdesignation

HardnessBrinell HB

Nominal compositionApproximate content in %

Ann. Aged Ni Cr Co Fe Mo W Mn Si Al Ti Others

Air Resist 13 1.0 79.6 2.5 11.0 3.5 4.12Air Resist 213 19.0 65.8 4.7 3.5 6.68Altemp S 816 20.0 20.0 47.6 4.0 4.0 0.4FSX 414 10.0 29.0 52.8 1.0 7.0 0.25Haynes 25* 10.0 20.0 49.0 3.0 15.0 1.5 0.5 0.1Haynes 36 10.0 18.5 52.8 2.0 14.5 1.2 0.6 0.4Haynes 151 20.0 65.6 12.8 0.5 0.5 0.15 0.47Haynes 188* 22.0 22.0 38.0 2.5 14.0 1.0 0.4 0.1HS 6* 2.5 28.0 60.5 3.0 5.0 1.0HS 21* 3.0 27.0 62.6 2.0 5.0 0.6 0.6 0.25HS 25 10.0 20.0 48.4 3.0 15.0 1.5 2.0 0.1HS 30 16.0 24.0 51.4 1.0 6.0 0.6 0.6 0.4HS 31 10.0 25.0 53.8 1.5 8.0 0.6 0.8 0.4HS 36 10.0 18.0 53.1 2.0 15.0 1.5 0.4J 1570* 28.0 19.0 39.0 2.0 7.0 J 1650 27.0 19.0 38.0 12.0 0.2Jessop 832 12.0 19.0 44.0 17.0 2.0 0.8 0.3 3.5Jessop 834 12.0 19.0 42.0 20.0 2.0 6.5Jessop 865 10.5 25.5 53.0 2.0 7.5 0.6 0.6 0.45Jessop 875 21.0 66.0 11.0 2.45Jessop 887 10.0 20.0 50.0 3.0 15.0 0.5 1.5 0.1Jessop X-40 10.5 25.5 53.0 1.5 7.5 0.75 0.75 0.5Jessop X-45 10.5 25.5 54.7 2.0 7.0 0.25Jessop X-50 20.5 25.5 40.3 4.0 12.0 0.75Jessop X-63 10.0 25.0 57.6 1.0 6.0 0.45Jetalloy 209 10.0 20.0 52.0 1.0 15.0 2.0 0.02L-251 10.0 19.0 56.0 1.0 14.0 0.4L-605 10.0 20.0 51.0 1.6 15.0 1.5 0.6 0.1M 203 25.0 20.0 38.0 1.6 12.0 0.8 1.0 0.7 2.0 1.67M 204 25.0 18.0 42.0 1.6 12.0 1.27M 205 25.0 18.0 40.0 1.6 12.0 2.7 1.67MAR-M 302 21.5 57.0 0.75 10.0 0.1 0.2 10.0MAR-M 322 21.5 60.0 0.75 9.0 0.1 0.1 0.75 7.7MAR-M 509 10.0 23.0 55.0 7.0 0.05 0.05 0.2 4.6MAR-M 905 20.0 20.0 55.0 0.5 7.65MAR-M 918 20.0 20.0 52.0 0.4 0.1 0.1 0.5 7.65Refractaloy 70 20.0 21.0 46.0 0.5 8.0 4.0 0.08V-36 20.0 25.0 43.2 2.4 4.0 2.0 0.6 0.5 2.29Wl-52 0.5 21.0 62.6 2.0 11.0 0.25 0.25 2.45

● Material Specifications Cross-Reference List-Aerospace Material Designation■ Co-based Heat Resistant Alloys

Infomation

K11

USA UK France Germany Others

SAE AMS BS AFNOR Werkst.-Nr DIN1706

(5534) LW2.4989 CoCr20Ni20W

5537C 5759 KC20WN LW2.4964 CoCr20W15Ni CoCr19W14NiB CoCr20W13 5772 KC22WN CoCr22W14Ni 5373 R30006 5385 3531 CoCr29Mo R30021

5759 KC20WN LW2.4964 CoCr20W15Ni 5380 CoCr25NiW R300305382 3146 LW2.4670 CoCr25NiW R30031 CoCr19W14NiB CoCr19Fe16NiMoVNb CoCr19Fe20NiMoVNb CoCr25Niw CoCr21W11Nb CoCr20W15Ni 5382 3156-2 LW2.4670 CoCr25NiW 5759 2.4964 CoCr20W15Ni R30605 CoCrW10TaZrB CoCr22W9TaZrNb 3146-3 CoCr24Ni10WTaZrB CoCr20Ni20Ta CoCr25NiMoWNb CoCr12MoW In

fomation

K12

Technical Data

Brinell hardness, 10 mm balls, 3000 kgf load

Vicke

rs Hardn

ess (HV)

Rockwell hardness

Shore ha

rdne

ss Tensile strengthKgf/mm2

[N/m2]Approximate value MPa ⑴

Standard ball

Tung

sten

ca

rbide tall Scale A

Load: 60 kgf brale

indenter(HRA)

Scale BLoad: 100 kgfDiameter

1/16’’ indenter(HRB)

Scale CLoad: 150 kgf

brale indenter(HRC)

- - 940 85.6 - 68 97- - 920 85.3 - 67.5 96- - 900 85 - 67 95- (767) 880 84.7 - 66.4 93- (757) 860 84.4 - 65.9 92

- (745) 840 84.1 - 65.3 91- (733) 820 83.8 - 64.7 90- (722) 800 83.4 - 64 88- (710) 780 83 - 63.3 87- (698) 760 82.6 - 62.5 86

- (684) 740 82.2 - 61.8 84- (670) 720 81.8 - 61 83- (656) 700 81.3 - 60.1 81- (647) 690 81.1 - 59.7 -- (638) 680 80.8 - 59.2 80

- 630 670 80.6 - 58.8 -- 620 660 80.3 - 58.3 79- 611 650 80 - 57.8 -- 601 640 79.8 - 57.3 77- 591 630 78 - 56.8 -

- 582 620 79.2 - 56.3 75- 573 610 78.9 - 55.7 -- 564 600 78.6 - 55.2 74- 554 590 78.4 - 54.7 -- 545 580 78 - 54.1 72

- 535 570 77.8 - 53.6 -- 525 560 77.4 - 53 71- 517 550 77 - 52.3 -- 507 540 76.7 - 51.7 69- 497 530 76.4 - 51.1 -

- 488 520 76.1 - 50.5 67- 479 510 75.7 - 49.8 -- 471 500 75.3 - 49.1 66- 460 490 74.9 - 48.4 -- 452 480 74.5 - 47.7 64

- 442 470 74.1 - 46.9 -- 433 460 73.6 - 46.1 62- 425 450 73.3 - 45.3 -- 415 440 72.8 - 44.5 59- 405 430 72.3 - 43.6 -

Brinell hardness, 10 mm balls, 3000 kgf load

Vicke

rs Hardn

ess (HV)

Rockwell hardness

Shore ha

rdne

ss Tensile strengthKgf/mm2

[N/m2]Approximate value MPa ⑴

Standard ball

Tung

sten

ca

rbide tall Scale A

Load: 60 kgf brale

indenter(HRA)

Scale BLoad: 100 kgfDiameter

1/16’’ indenter(HRB)

Scale CLoad: 150 kgf

brale indenter(HRC)

- 397 420 71.8 - 42.7 57- 388 410 71.4 - 41.8 -- 379 400 70.8 - 40.8 55- 369 390 70.3 - 39.8 -‒ 360 380 69.8 (110.0) 38.8 52

- 350 370 69.2 - 37.7 -- 341 360 68.7 - 36.6 50- 331 350 62.1 - 35.5 -- 322 340 67.6 - 34.4 47- 313 330 67 - 33.3 -

247 247 260 62.4 (101.0) 24 37 825243 243 255 62 - 23.1 - 805238 238 250 61.6 99.5 22.2 36 795233 233 245 61.2 - 21.3 - 780228 228 240 60.7 98.1 20.3 34 765

219 219 230 96.7 (18.0) 33 730209 209 220 95 (15.7) 32 695200 200 210 93.4 (13.4) 30 670190 190 200 91.5 (11.0) 29 635181 181 190 89.5 (8.5) 28 605

171 171 180 87.1 (6.0) 26 580162 162 170 85 (3.0) 25 545152 152 160 81.7 (0.0) 24 515143 143 150 78.7 22 490133 133 140 75 21 455

124 124 130 71.2 20 425114 114 120 66.7 - 390105 105 110 62.3 - -95 95 100 56.2 - -90 90 95 52 - -

86 86 90 48 - -81 81 85 41 - -

⑴ 1 MPa = 1 N/mm2

⑵This table is an excerpt from the JIS Iron and Steel Handbook⑶Values in parentheses in the above table are not usually used

■ Hardness Comparison Chart

Infomation

L1

Index

L

Index

L2

IndexItem number Description Page number

1160 Parts F6, F10, F11, F16

1180 Parts F10, F11, F16

1182 Parts F16

2413 Parts F16

2415 Parts F6, F10, F11

2417 Parts F6, F10, F11, F16

3919 Parts F16

9414 Parts F6, F10, F11, F16

1/4-20UNC×11/2 Parts F20

1/4-20UNC×11/4 Parts F20

2814HS Parts Ⅰ18

3/8-16UNC×11/2 Parts F20

A..R..-SDW Cutter Ⅰ14

ACN423 Parts F6, F7, G4

ADN423 Parts F8, F9, G4

AMS Parts Ⅰ4, Ⅰ5

AOB Parts H12, Ⅰ4, Ⅰ5

AOS-5 Parts J48, J71

AOS-6 Parts F6, F7, F8, F9, F11, F12, F13, F14, F15, G4, G5

APCW Insert Ⅰ17

APCW..PD Insert Ⅰ17

APCW..PDSR Insert Ⅰ17

ARP Parts Ⅰ4

ASG-5 Parts J48, J71

ASG-6 Parts H12

ASGL6-D Parts F6, F7, F8, F9, F11, F12, F13, F14, F15, G4, G5

ASN423 Parts F11, G5, Ⅰ6, Ⅰ8, Ⅰ10

ATN323 Parts F14

AVN323 Parts F12, F13

AWN423-W Parts F15, G5

B23 Insert Grade A3, C4, D24

B30 Insert Grade A3, C4, D24

B36 Insert Grade A3, C4, D25

B40 Insert Grade A3, C4, D25

B52 Insert Grade A3, C4, D25

BACK DUO Back Turning B8, J3

BAS 20 Parts F17, H7

BGC Parts H7

BGR Toolholder J111

BGV Parts H7

BN Parts F17

BNS Parts F17

BRCL Parts F17

BRCN Parts F17

BRCR Parts F17

BRCS Parts F17, H7

BRV Parts F17

BS0620 Parts J59

BS20 Toolholder F17, H7

C045F Toolholder J106

C05G Toolholder J107

C06H Toolholder J108, J109

C07J Toolholder J108, J109

C08K Toolholder J108, J109

Item number Description Page numberC10M Toolholder J108, J109

C12M Toolholder J108, J109

C7X Insert Grade D29, D31, Ⅰ3

C7Z Insert Grade A5, D29, D31

CCET Insert E28

CCGT Insert E27, E28, E29

CCGW Insert E2, E22, E29

CCLN Toolholder F6

CCMT Insert E27, E28, E29

CCMW Insert E22

CDH Insert E2

CH-FGV Toolholder J77

CL1-1-E Parts H9, H10

CL2RV Parts F18, F19

CL3RV Parts F18, F19

CL4RV Parts F18, F19

CLR Parts J133

CM-72 Parts H11

CM-73 Parts H11

CNG Insert E3

CNGA Insert E4, E22, E30

CNGA..WL Insert E5

CNGA..WLM Insert E5

CNGG Insert E5, E30

CNGX Insert E6

CNMA Insert E22

CNMG Insert E30

CP1 Insert Grade D35, D38

CPGH Insert E31

CPGP Insert E31

CPGR Insert E31

CPGT Insert E31

CPMH Insert E31

CPR5 Parts J48

CR1-1-E Parts H9, H10

CRGN Toolholder F16

CS0309-TW Parts J88

CS0310 Parts J88

CS0316 Parts F20

CS0410 Parts J88

CS04148S Parts J88

CS0510A Parts Ⅰ18

CS0510T Parts Ⅰ18

CS0512T Parts Ⅰ18

CS0515 Parts J88

CS0520 Parts J88

CS0620 Parts J88

CS0625 Parts F20

CS1040A Parts Ⅰ18

CSDNN Toolholder F11

CSKN Toolholder F10

CSRN Toolholder F10

CSSN Toolholder F10

CSV Toolholder J37, J43, J60, J73, J85, J131

Index

L3

Item number Description Page numberCSVB Insert J43, J130

CSVC Insert J60, J130

CSVF Insert J37, J130

CSVG Insert J73, J130

CSVT Insert J85, J130

CTDP Insert J58

CTDP Toolholder J58

CTP Insert J54, J55

CTP Toolholder J56, J57

CTPA Insert J54, J55

CTPA Toolholder J46, J56, J57

CTPS Insert J60

CTP-SH Cut Off B8, J54

CTPSR Toolholder J60

CTPW Insert J54, J55

CTPW Toolholder J56

CTV Insert J59

CTV Toolholder J59

CUT DUO Cut Off B8, J2

CV Parts H12

CVS Parts J71

CZH Insert J115

DAS41 Parts H9, H10

DB1-1 Toolholder H9

DB7-1-7 Toolholder H10

DBA Parts H10

DC5TN Parts F14

DC6CN Parts F6, F7, F11, F15, G4

DC6DN Parts F8, F9, G4

DC6VN Parts F12, F13

DCET Insert E33

DCGT Insert E32, E33, E34

DCGW Insert E23, E34

DCMT Insert E32, E33, E34

DCMW Insert E23

DM4 Insert Grade A4, A5, D35, D36

DNG Insert E6

DNGA Insert E7, E23, E36

DNGG Insert E7, E35, E36

DNGX Insert E8

DNMA Insert E23

DNMG Insert E35, E36

DPGT Insert E37

DS Sleeve Sleeve B9, J11

DS-ACH Toolholder B8, J8

DS-CSVL Toolholder J37, J43, J60, J73, J85, J129, J131

DS-FGV Toolholder J77

DS-GTTL Toolholder J70, J127

DS-LBMBL Toolholder J105, J128

DS-PTXL Toolholder J34, J126

DS-SCLL Toolholder J27, J124

DS-SDUL Toolholder J30, J125

DS-SVVPN Toolholder J32, J126

DS-SVXL Toolholder J31, J125

Item number Description Page numberDS-TBPL Toolholder J45, J127

DS-TTPL Toolholder J83, J128

DT4 Insert Grade A4, A5, D35, D36

E..R..SDW Cutter Ⅰ15

ERGP Insert E37, J107

EZ CUBE CBN Series A3, D24, D25

FBV Insert J76

FDX Insert Ⅰ7, Ⅰ9, Ⅰ11

FGV Insert J76

FGVR Toolholder J77

FSI02-2.2×4.0 Parts J115

FSI02-2.2×4.3 Parts J115

FSI0306A Parts Ⅰ18

FSI0307A Parts Ⅰ18

FSI035104A Parts Ⅰ18

FSI17-2.2×6.0 Parts J88

FSI21-5.0*12.45 Parts Ⅰ14, Ⅰ15, Ⅰ16

FSI22-4.0*11 Parts Ⅰ17

FSI23-4.0*7 Parts Ⅰ17

FSI24-2.2×7.9 Parts J88

FSS15-3.0*12 Parts F6, F7, F8, F9, F11, F12, F13, F14, F15

FSS16-3.0*8 Parts G4, G5

GKN Insert H11

GKP Insert H11

GTG Insert J111

GTMH Insert J67, J68

GTMX Insert J66

GTPA Insert J72

GTPAR Toolholder J72

GTT Toolholder J49, J69

GTVW Toolholder J71

GVW Insert J71

HACDH Parts F20

HAD Insert Ⅰ18

HAL Insert Ⅰ18

HAN Insert Ⅰ18

HC1 Insert Grade B5, C4, D3, D4

HC2 Insert Grade B4, B6, C4, D3, D6

HC5 Insert Grade B6, C4, D3, D7

HC6 Insert Grade B4, B6, C4, D3, D7

HC6CN Parts F6, G4, G5

HC6DN Parts F8, F9, G4

HC6SN Parts F11

HC6VN Parts F12, F13

HC7 Insert Grade C4, B6, D3, D8, Ⅰ3

HLA Insert Ⅰ18

HLR-25S Parts Ⅰ12

HLW175 Parts Ⅰ6, Ⅰ8, Ⅰ10

H-M4×12 Parts J88

HN59Z Toolholder J112

HPC Milling Cutter B10, Ⅰ18

HRCD Toolholder F20

HRT Insert Ⅰ18

HW2 Insert Grade B5, C4, D3, D5

Index

L4

IndexItem number Description Page number

HY-NBH Toolholder J96

ICSN434 Parts F6

ICSN454 Parts F6

IRSN43 Parts F16

IRSN45 Parts F16

IRSN53 Parts F16

ISSN434 Parts F10, F11

ISSN454 Parts F10, F11

ISSN534 Parts F10, F11

JFDX..45 Cutter Ⅰ6

JFDX..75 Cutter Ⅰ8

JFDX..88 Cutter Ⅰ10

JQTE Cutter Ⅰ17

JQTS Cutter Ⅰ17

JRNMW Cutter Ⅰ5

JRPMW Cutter Ⅰ4

JSDW..45 Cutter Ⅰ14

JSDW..75 Cutter Ⅰ15

JXTM Cutter Ⅰ12

KM1 Insert Grade D35, D38

L1E Parts H9

L2E Parts H9

LBM Insert J104

LBMAR Toolholder J105

LCL4 Parts J35

LCS4CA Parts J35

LLR- Parts J133

LNJ Insert E8

LNX Insert Ⅰ13

LRIS- Parts J132

LR-S Parts J133

LSC42 Parts J35

LSP4 Parts J35

LW-2 Parts J96

LW-2.5 Parts F20, J48, J71, J129

LW-3 Parts J35

LW-4 Parts F6, F10, F11, F16, H12, J59, J129

LW-5 Parts F20

LWU-4 Parts F20

LWU-5 Parts F20

M3*8 Parts Ⅰ4, Ⅰ6, Ⅰ8, Ⅰ10

MBC-M12 Parts Ⅰ18

MBC-M16 Parts Ⅰ18

MBL Insert J106

Mogul Bar ID Tooling B9, J9

NBH Toolholder J102, J103

NS Toolholder H11

P..R..SDW Cutter Ⅰ16

PCLNR Toolholder J34

PD1 Insert Grade B9, D26

PTXNR Toolholder J34

Q15 Insert Grade A5, D29, D30

QM3 Insert Grade A5, D35, D37

R1E Parts H9

Item number Description Page numberR2E Parts H9

RA Cutter Ⅰ18

RA06P03NC Parts Ⅰ18

RCGX Insert E9

RCGX10 Insert E9

RCMX Insert E38

RD Cutter Ⅰ18

REZ Toolholder J115

RKN Insert H11

RNG Insert E10

RNIW Cutter Ⅰ5

RNMG Insert E38

RPG Insert E11

RPGX Insert E11

RPIW Cutter Ⅰ4

RPMT Insert E38

RPMX Insert E38

S..WCLN Toolholder G4

S..WDUN Toolholder G4

S..WSKN Toolholder G5

S..WWLN Toolholder G5

S06F Toolholder J106, J108

S06G Toolholder J107

S07G Toolholder J108, J109

S08G Toolholder J107

S08H Toolholder J108, J109, J111

S10K Toolholder J108, J109

S12M Toolholder J108, J109

S16Q Toolholder J109

S-412 Parts H11

SATURN DUO Grooving B9, J12

SBFS Insert J98

SBG Insert J100

SBT Insert J101

SC02C Parts F18, F19

SC05C Parts F18, F19

SC06C Parts F18, F19

SC10F Parts F18, F19

SC40F Parts F18, F19

SC40F10 Parts H9, H10

SCG Insert E12

SCGW Insert E12

SCLC Toolholder J26

SCMT Insert E39

SDC Insert E39

SDCW Insert E12, E39, Ⅰ14, Ⅰ15, Ⅰ16

SDCW..AE Insert Ⅰ14

SDCW..EE Insert Ⅰ15

SDCW..PE Insert Ⅰ16

SDJC Toolholder J28

SDKN Insert E39

SDNCN Toolholder J28

SDW..45 Insert Ⅰ14

SDW..75 Insert Ⅰ15

Index

L5

Item number Description Page numberSECN Insert E39

SEKN Insert E39

SFG Insert J100

SHF Insert J94, J95

SHFB Insert J98

SM2RV Parts F18, F19

SM2RVS Parts F18, F19

SM3RV Parts F18, F19

SM4RV Parts F18, F19

SNEN..ZN Insert Ⅰ11

SNG Insert E13, E14, E41, Ⅰ7, Ⅰ9, Ⅰ11

SNG..AN Insert Ⅰ9

SNG..EN Insert Ⅰ7

SNGA Insert E14, E24

SNGF Insert Ⅰ7, Ⅰ9, Ⅰ11

SNGG Insert E40, E41

SNGX Insert E14

SNMA Insert E24

SNMG Insert E40

SP2 Insert Grade B4, C4, D3, D11, Ⅰ3

SP9 Insert Grade A2, B4, C4, D3, D11, Ⅰ3

SPC Insert E42

SPCE Insert E42

SPEB Insert E42

SPG Insert E14, E24, E42

SPGR Insert E42

SPKN Insert E42

SPM Insert E42

SPME Insert E42

SPMH Insert E42

SPMR Insert E42

SS040 Parts J96, J102, J103

SS0506 Parts J129

SS0515 Parts J129

SS0812R Parts J96

SS-DSU Toolholder J129

STAC Toolholder J33

STICK DUO Hyper ID Tooling B9, J10

SVJC Toolholder J31

SVXP Toolholder J32

SX1 Insert Grade B4, C4, D3, D11, Ⅰ3

SX5 Insert Grade B2, C4, D3, D13, D14, D15, H5, Ⅰ3

SX6 Insert Grade B5, C4, D3, D10, Ⅰ3

SX7 Insert Grade A2, B2, C4, D3, D12, D14, D15, H5, Ⅰ3

SX8 Insert Grade Discontinued

SX9 Insert Grade B3, C4, D3, D13, D14, D15, Ⅰ3

T-07 Parts J88, J115

T-15A Parts Ⅰ6, Ⅰ8, Ⅰ10, Ⅰ17

T-20 Parts Ⅰ14, Ⅰ15, Ⅰ16

T3N Insert Grade Discontinued

TAS Insert Grade Discontinued

TB Insert J48

TBDP Insert J42

TBDP Toolholder J42

Item number Description Page numberTBGE Insert E16, E43

TBMH Insert J49

TBP Insert J44

TBPA Insert J46

TBPR Toolholder J44

TBR Toolholder J48

TBTR Toolholder J48

TBVC11 Insert J47

TBVCR Toolholder J47

TC5TN Parts F14

TC6CN Parts F6, F7, F11, G4, G5

TCGD Insert E43

TCGH Insert E43

TCGP Insert E43

TCGT Insert E43

TCGW Insert E43

TCMT Insert E43

TEEN Insert E43

TF33 Insert J36

TFD Insert J28

TFT Insert J33

TFTR Toolholder J36

TFV Insert J31

TGC Toolholder J112

TM4 Insert Grade A4, A5, D35, D36

TMG Insert J68

TMN Insert J112

TNEG Insert E44

TNG Insert E16, E17

TNGA Insert E18, E25, E44

TNGG Insert E18, E44, E45

TNMA Insert E25, E45

TNMG Insert E44, E45, E46

TNMP Insert E46

TP Insert E19, E47

TPC Insert E47

TPG Insert E19, E25, E47

TPGD Insert E47

TPGE Insert E19, E19, E47

TPGH Insert E47, E48

TPGP Insert E48

TPGR Insert E48

TPGS Insert E48

TPGW Insert E25

TPKN Insert E48

TPM Insert E48

TPMR Insert E48

TTP Insert J82

TTP Toolholder J83

TW Insert J87

TWC Toolholder J88

U104-40 Parts Ⅰ18

U107T10 Parts Ⅰ18

VBGT Insert E49

Index

L6

IndexItem number Description Page number

VBGW Insert E26, E49

VCET Insert E49

VCGT Insert E49

VCGW Insert E26, E49

VCMT Insert E49

VCMW Insert E26

VDB Insert H8

VDB..R Insert H8

VGE Insert H12

VGT Toolholder H12

VGW Insert H6

VGW..R Insert H6

VM1 Insert Grade A5, D35, D37

VNG Insert E20

VNGA Insert E20, E26, E50

VNGG Insert E50

VNMG Insert E50

VNMP Insert E50

VPET Insert E50

VPGT Insert E50

VRAO Toolholder F18

VRAON Toolholder F19

W106 Parts F20

W107 Parts F20

W110 Parts F20

W120 Parts F20

WA1 Insert Grade B3, B4, B6, C4, D3, D9, D14, D15, H5, Ⅰ3

WCBN Toolholder F7

WCGT Insert E51

WCLN Toolholder F6

WDHN Toolholder F8

WDJN Toolholder F8

WDNNN Toolholder F9

WNGA Insert E21

WNGG Insert E51

WNMG Insert E51

WPGT Insert E51

WS0616-T15 Parts Ⅰ6, Ⅰ8, Ⅰ10

WSDNN Toolholder F11

WSSN Toolholder F11

WTFN Toolholder F14

WTGN Toolholder F14

WVJN Toolholder F12

WVPN Toolholder F12

WVVNN Toolholder F13

WWLN Toolholder F15

XN4 Insert Grade D29, D31

XT3 Insert Grade D29, D30

XX2815-04 Parts Ⅰ12

XX2815-04-25S Parts Ⅰ12

Y-axis Holder Toolholder B9, J120

Y-CTPA Toolholder J46, J121

Y-GTPA Toolholder J72, J122

Y-GTTR Toolholder J70, J122

Item number Description Page numberY-SDJCR Toolholder J29, J120

Y-SDNCN Toolholder J29, J120

Y-SVJCR Toolholder J31, J121

Y-TBPR Toolholder J45, J121

ZC4 Insert Grade B7, C4, D3, D8

ZC7 Insert Grade B7, C4, D3, D8

ZM3 Insert Grade A5, D35, D37

Index

NGK SPARK PLUGS (U.S.A), INC.Cutting Tool Sales Office

46929 Magellan Dr., Wixom, Ml 48393 U.S.A.Tel. ; +1-248-668-0100Fax ; +1-248-668-0200

www.ntkcuttingtools.com

NGK DO BRASIL LTDA.CERAMICA E VELAS DE IGNICAO

Estrada Mogi-Salesopolis, km 09 Bairro Cocuera,Mogi das Cruzes (SP), Brazil

Tel. ; +55-11-4793-9092Fax ; +55-11-4793-8270

www.ngkntk.com.br

NGK SPARK PLUGS (U.K), LTDMaylands Avenue, Hemel

Hempstead, Herts, HP24SD, U.K.Tel. ; +44 1442-281-000Fax ; +44 1442-281-080

www.ntkcuttingtools.co.uk

NTK TECHNICAL CERAMICSKOREA CO.,LTD.

680-14 Kojan-Dong, Namdong-kuIncheon, Korea

Tel. ; +82-32-815-6763Fax ; +82-32-815-6762

www.kntktool.co.kr

NGK Spark Plug (Shanghai) Co., Ltd.No.736 Songsheng Road SongjiangIndustrial Zone, Shanghai 201613,

The People's Republic of ChinaTel. ; +86-21-63857652Fax ; +86-21-63853690

www.ngkntk.com.cn

Bujías NGK de México, S.A. DE C.V.Carretera Lago de Guadalupe, Km. 27.5,

S/N, Bodega 3-A, Col. San Pedro Barrientos, Tlalnepantla, Estado de México, C.P. 54010

Tel. ; +52-55-5317-5872Fax ; +52-55-5317-5876

www.ngkntk.com.mx

NGK SPARK PLUG EUROPE GmbHHarkortstr.41

40880 Ratingen, GermanyTel. ; +49 2102 974-350Fax ; +49 2102 974-399

www.ntk-cutting-tools.com

NGK SPARK PLUGS (THAILAND) CO.,LTD.Amata Nakorn Industrial Estate (Phase 8)

700/864 Moo 1, Tambol Panthong,Amphur Panthong, Chonburi Province 20160, Thailand

Tel. ; +66-38-185-306Fax ; +66-38-185-316

NGK SPARK PLUG CO.,LTD.Technical Ceramics Group Cutting Tool

Overseas Sales & Marketing 2808, Iwasaki, Komaki, Aichi

485-8510, JapanTel. ; +81-568-76-1538Fax ; +81-568-76-1288

www.ngkntk.co.jp

SPARK PLUGS (USA), INC.

DISTRIBUTED BY

【Mar.,2013】

NTK Cutting ToolsDivision of NGK Spark Plugs USA46929 Magellan Drive, Wixom, MI 48393, U.S.A.Phone: 248-668-0100 Fax: 248-668-0200Toll Free: 866-900-9800

www.ntkcuttingtools.comwww.youtube.com/ntkcuttingtools