Embed Size (px)
Citation preview
Literature Materials:□ Greetings to Go
Tools and Supplies:□ Scor-Pal®□ Adhesive□ Tape□ CS® Foam Adhesive Circles□ Paper Trimmer□ 3x14” CS® Grid Ruler□ Scissors
□ CS® Glue Pen□ CS® Earth Ink□ CS® Ink Applicator □ Corner Chomper Punch□ 1” Circle Punch□ 1/8” or 1/4” Hole Punch or Cropadile
Preparation:
1. Trim the Ivory printed cutaparts into sections as indicated by the artwork and cutting guidelines. Several extra cuts are included to help eliminate difficult transitions where colored areas meet the edge of the artwork.
2. Scoring and folding information is listed within the instructions for each card set. TIP: The “bump” of the score goes on the inside of the fold.
3. If you do not have an item to complete the card as shown, simply omit or substitute the item.
To view more details about the layouts and cards, visit the following link: clubscrap.com/1016-layouts-cards/
All rights reserved. ©2016, Club Scrap, Inc. (888) 634-9100 • www.clubscrap.com • email: [email protected]
Assembly Line Cardmaking
October 2016 Greetings to Go
Literature
October 2016 • Literature Greetings to Go • Page 2 of 4
Set A: 3½x4¾” Dk. Kraft Cards with 4½x6½” Red Panels Score each Dk. Kraft card horizontally at 1½, 3, 5¼ and 7½”. Accordion fold on the score lines.Trim each 4½x6½” Red Panel horizontally at 5¼ and 3¼”. Adhere the three Red panels measuring 1¼x4½, 2x4½, and 3¼x4½” to the corresponding flaps on each Dk. Kraft card base.
©2016, Club Scrap, Inc. (888) 634-9100 • www.clubscrap.com • email: [email protected]
Notes: (Assembly process is the same for all four cards.) Round the right corners of each Ivory cutapart; adhere one cutapart to each flap, being careful to limit the adhesive to the flap area only; space the cutaparts evenly from top to bottom.
Notes: Tie a bow around the 2x4.5” Red panel prior to attaching to the center flap of the card base.
October 2016 • Literature Greetings to Go • Page 3 of 4
Set B: 4¼x5½ Lt. Kraft Cards with 2¾x4” Brown and 2¼x3” Red PanelsScore and fold each 5½x8½” Lt. Kraft card horizontally at 4¼”. Score and fold two 2¾x4” Brown panels horizontally at 2”. Score two 2¾x4” Brown panels horizontally at 1 and 3” and fold to make a gate fold.
©2016, Club Scrap, Inc. (888) 634-9100 • www.clubscrap.com • email: [email protected]
Notes: Trim a decorative cutapart strip to 1x5.5”, wrap with ribbon, and adhere to the lower third of the card base; adhere the “Once upon a time” cutapart to the left flap of a gate folded Brown panel; glue a metal corner to the lower right corner of the cutapart; adhere “I'm happy to be part of your story” to the inside of the Brown piece; wrap with red ribbon and tie with a bow; nest onto the Red panel and adhere to the card; inside: “Wishing you a beautiful day.”
Notes: Trim an Ivory cutapart to 1x5.5”, wrap with red ribbon and adhere to the left side of the card base; nest a Brown folded panel onto the Red panel; make a small loop of red ribbon and sandwich between the front of the Brown panel and the “voyage extraordinaires” cutapart; glue a metal corner to the lower right corner of the cutapart; adhere the “Write the story...” cutapart to the inside of the folded Brown panel; inside: “Enjoy”!
Notes: Trim an ivory cutapart strip to 1x5.5” and adhere to the left edge of the card base; nest a folded Brown panel onto a Red panel; make a small loop of red ribbon and sandwich between the “Alice's Adventures” cutapart and Brown flap; glue a metal corner to the cutapart; adhere “A short story of thanks” to the inside of the folded Brown panel; inside: “You are so thoughtful.”
Notes: Trim an Ivory cutapart strip to 1x5.5” and adhere to the left side of the card base; nest the gate folded Brown panel onto the Red panel; adhere the “You can.” cutapart to the left flap of the gate fold; glue a metal corner to the right corner of the cutapart; adhere “End of story.” to the inside of the Brown panel; inside: “Good luck!”
October 2016 • Literature Greetings to Go • Page 4 of 4
Set C: 5x7” Red Cards with 4½x6½” Bronze PanelsScore and fold each 7x10” Bronze panel horizontally at 5”.
©2016, Club Scrap, Inc. (888) 634-9100 • www.clubscrap.com • email: [email protected]
Notes: Follow the same procedure as with the previous card; library card cutapart reads “I've fined myself two dollars on your behalf.”; inside: “Belated Birthday Wishes.”
Notes: Cut the “Make a wish.” frame from the Ivory cutapart with a craft knife; adhere the frame portion of the cutapart to the front of a library card pocket, wrap with ribbon, and adhere the “wish” portion with foam adhesive; cut the decorative circle from the Ivory cutapart and fold over the top of the library card cutapart that reads “Did you wish for an awesome card?”; stick the pocket to the card panel; inside: “Happy Birthday.”
Notes: Adhere the “Ex Libris” cutapart to the front of the library card pocket; round the top corners of the library card cutapart; punch a hole in the top center of the card and tie with ribbon; insert the card in the pocket and adhere the pocket to the card panel; inside: “Enjoy it thoroughly.”
Notes: Adhere the “Alice in Wonderland” cutapart to the library card pocket; round the top corners of the “I
wonder...” cutapart, punch a hole in the top center, and add tie with ribbon; add ribbon to the bottom of the Bronze panel and adhere to the card base; center the library card
pocket onto the card; inside: “”Happy Birthday!”
