Omega Denali Manual

8/10/2019 Omega Denali Manual

http://slidepdf.com/reader/full/omega-denali-manual 1/14

Omega DENALITM

Adjustable-Height Desk System

INSTALLATION MANUALVERSION 1.0



BEFORE YOU BEGINPROVIDED:

(19) M6 hexagonal

machine bolts

(10) 5x20 mm

Machine Screws

(4) Foot Caps

(2) Support ArmsRight and Lef

(2) Hex Wrenches (2) Feet

(2) Liing LegsRight and Lef

(1) Crank Handle

(1) Drive ShaRight, lef, and center

(2) CrossbarsIdentical (1) Crank Sha

Identical

(1) Omega table top

R

LR

L

*ruler in inches & millimeters foryour convenience



(1) Keyboard Plaorm Mounng Assembly

(2) Keyboard Plaorm Supports

(2) Carriage bolts

(2) Rubber bumpers

(1) Keyboard Plaorm

(1) Keyboard fence

(6) Spacers

(6) #10 1-1/4” fat head

Phillips screws

(7) #10 5/8” pan head

Phillips screws

(8) M5 20mm pan head

machine screws

ROVIDED FOR KEYBOARD TRAY ASSEMBLY:

STEP 11

STEPS 11 & 14STEP 12

R E A D T H I S CONGRATULATIONS on your purchase o an OmegaDENALI™ adjustable-height desk system! We designedthis product to be as easy as possible to assemble, buti you have any questions during the assembly processplease contact our Customer Care team using theinormation on the back page.

SHOULD you be installing your owntable top on the ELLURE rame, besure to drill pilot holes beore inserting woodscrews. Te wood screws supplied with the ELLUREbase should work with most table tops. It is critical to

pay attention to the available depth for pilot holes so a

not to damage the lamination of the table top surface.



the feet are compatible withboth the right or left leg

ASSEMBLY INSTRUCTIONS

CLEAR a good-sized area to lay out all componentsand assemble the desk. Lay the table top down on the floor,laminate side down. I not on carpet, we recommend

placing a sof blanket down first in order to protect thetable top surace. Make sure the entire area is clear o anyloose screws or debris, to avoid scratching the laminatedsurace. Alternatively, this can all be done on top o anothertable rather than on the floor. Be careul not to slide thetable top while upside-down, to protect the laminate.

THE ELLURE base is designed to work with any table top,though assembly is easiest when using a genuine ELLUREtable top. ELLURE table tops include threaded insert nutsthat remove any conusion as to where to drill, the bit size

to use, or how deep to drill. Tese recessed nuts also extendthe lie o the product, by preventing degradation o thewood fibers rom over-tightening and rom removing andreinstalling wood screws too many times.

1PREPARE FOR ASSEMBLY

FOR THIS STEP:

ATTACH one oot to each lifing leg with our (4) M6

machine bolts provided.

SET the right and lef lifing legs upside down on the table.Ensure they are positioned correctly on the table top,reerring to the diagram below. Te right lifing leg willhave the crank gear housing attached. Insert one end oeach crossbar into the opposing ends o the lifing legs,connecting the two legs together.

2 ATTACH FEET AND SET CROSSBAR

IN LEGS

FOR THIS STEP:

the right lifting leghas the crank shaft

housing module

CAUTION!

R L



ATTACH the lef and right top arms to theirrespective lifing columns using our (4) M6 machinebolts or each top arm. Make sure the top support arms areacing outwards. Do not tighten these bolts all the way.

3 ATTACH ARMS TO LEGS

FOR THIS STEP:

EXTEND the base to the appropriate width, sothat the holes in the base are aligned with the recessed nutson the table top. Secure the base to the table top with theappropriate machine screws. You may now tighten the toparm screws rom Step 3.

4 ATTACH BASE TO TABLE TOP

FOR THIS STEP:

R

R

L

L

R

L

x3

x3

use the smaller hex wrench for tset screws

not provided

the four (4) set screwsare located on the

bottom of the crossbars



INSERT the two rods into the drive shaf. Positionthe drive shaf between the two legs and expand

the drive shaf until the two rods are inserted into theirrespective legs.

5INSERT DRIVE SHAFT

FOR THIS STEP:

1 2

3

aerial view of underside

drive shaft



ATTACH a oot cap to the end o each oot.7 ATTACH FOOT CAPS

FOR THIS STEP:

INSERT the crank shaf into the crank gearhousing on the right leg. Affix the crank shaf to

the top arm using three (3) M6 machine bolts.

6 ATTACH CRANK TO ARM

FOR THIS STEP:

crank gear housingcrank shaft



ATTACH the two oot supports to the undersideo the keyboard platorm using three #10 1-1/4” flathead Phillips screws and three spacers per oot support.Position each set o spacers between the oot support andthe underside o the keyboard platorm. DO NOT placewashers between screw head and foot support.

Position the tube assembly by matching the squaremounting plate to the triangular pattern o recessed holesin the center o the underside o the keyboard platorm.Attach the mounting assembly to the underside o thekeyboard platorm using our #10 5/8” pan head Phillips

8 ASSEMBLE KEYBOARD PLATFORM

FOR THIS STEP:

IN ORDER: WASHER, FOOTREST, SCREW

6x2x

6x

4x



USING eight M5 20mm pan head machinescrews, attach the mounting assembly and platorm tothe underside o the desk. Align the tube assembly bymatching the our holes on each mounting bracket to theour insert nuts on both sides o the Omega cutout.

9 ATTACH KEYBOARD PLATFORM

FOR THIS STEP:

8x

10 CAREFULLY FLIP THE DESK UP

DO NOT drag the tabletop alongside its edges. Doing so may

result in scratches. Insert crank handle into the crank shaf.

FOR THIS STEP:

handle folds outof crank



TILT the Omega keyboard platorm so that youcan easily access both the top and bottom o the

rear end o the platorm. Using three #10 5/8” pan headPhillips, attach the keyboard ence to the back o theplatorm so that the built-in cable guide is acing up whenthe keyboard platorm is flat.

11 ATTACH KEYBOARD FENCE FOR THIS STEP:

3x

we recommend tilting the

platform up for easier access

align the three holes of the

fence with the three holes on thebottom of the platform. once

alugned, use the pan-head screws

to attach the two together.

once the fence is attached to the

platform, you’re ready to install

the bumpers!



AFTER connecting all the cables and testing that

the desk is working properly, you may want to use thesupplied sel-adhesive cable guides to tidy up the cablesor a cleaner appearance.

13 FINAL TOUCHESFOR THIS STEP:

ATTACH each rubber keyboard bumper tothe keyboard platorm by fitting a carriage bolt

through each o the two slots cut into the platorm so thatthe bolt’s head is flush with the underside o the platorm.Secure each bumper in place by using your hand to twistthe rubber bumper o the bolt over the screw threads.

12 ATTACH RUBBER BUMPERSFOR THIS STEP:

2x 2x

on the bottom of the platform,

put the carriage bolts through

the slots.

twist the rubber bumpers over

the bolts until they are secured

this is what the keyboard

platform should look like from

your perspective after you’re

done.



THE OMEGA Keyboard Platorm can be set to one o two height positions. By deault, the bar assembly arrives setthe lower position. You can adjust the bar assembly higher by removing the two hex screws rom both ends o the pivbar, and reattaching the bar by inserting those same hex screws through the upper set o holes on the bracket.

o adjust the Omega Keyboard Platorm, simply loosen the central clamp by twisting the rubberized kncounterclockwise. Ten push down on the rear end o the platorm or a steeper angle or push up rom the bottom o platorm or a shallower angle. Once you have the platorm set to the desired position, secure it in place by tightenithe rubberized knob by twisting it clockwise.

Depending on the depth and shape o your keyboard you may want to adjust the rubber bumpers orward or back. do this, simply loosen the rubber bumper, slide it to the desired location, and retighten.

USING THE OMEGA KEYBOARDPLATFORM

OPTIONAL ACCESSORIES

1 2 3

THERMODESK INSURFACE DUALAC POWER SOCKET

THE 3” grommet holes provided in the OMEGA tabletops are ideally sized or accepting the flush-mountedpower socket “nodes.”



WARRANTYTHE THERMODESK ELLURE warranty coverage includes 5 years on table tops, and 2 years on the base. Te ollowilimitations apply:

THIS WARRANTY only covers deects as specified herein and does not include deects or damages attributable improper installation, misuse or normal surace weathering, or deects or damages caused by accidents or fire or othcasualty or Acts o God, or any other causes or occurrences beyond the manuacturer’s control. Te exclusive remedaction provided or the customer hereunder shall be repair, restoration or replacement o the components as are outo be deective.

TABLE TOP: Te replacement o new materials or those as may be deective may result in a color variance in comparisto the originally installed laminates due to slight color or texture changes by laminate manuacturers and is not indicato a deect. iMovR reserves the right to substitute such laminates as are then being manuactured and is only obligatto match color and quality with such products as it is manuacturing at the time o replacement.

THIS WARRANTY is limited to repair, restoration and/or replacement by iMovR o any deective unit provided tmanuacturer: (a) receives a written, axed or emailed notice o claim under this warranty, including sufficiently hiresolution photographs that clearly show the nature o the damage, and (b) within 30 days afer notice o claim, is receipt o the deective unit at its place o business, unless this requirement is waived by iMovR. Te manuacturer warrange or retrieval o the deective product via its carrier-o-choice. In some cases the manuacturer may elect notretrieve the deective component, and may opt to send a replacement product based only on photographic evidence

warrantied deects. I upon receipt and inspection o the returned component it is determined that the damage was ndue to a manuacturing flaw but rather one o the exempted reasons stated above, the costs o shipping the units to arom the manuacturer, plus the cost o the replacement component, shall be charged back to the customer.

LIMITATION OF LIABILITY: IT IS UNDERSTOOD AND AGREED THAT MANUFACTURER’S LIABILIT

WHETHER IN CONTRACT, IN TORT UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWIS

SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF PURCHASE PRICE FOR THE DEFECTIVE ITE

PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR SPECIA

INDIRECT OR CONSEQUENTIAL DAMAGES. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF TH

TRANSACTIONS UNDER THIS AGREEMENT MAY BE BROUGHT BY THE PURCHASER MORE THAN ON

YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED.

PREVENTATIVE MAINTENANCE AND CLEANINGAFTER first week o use: ighten down all screws and bolts.

CLEANING THE BASE: Clean the base rame by wiping it down with a microfiber cloth moistened with a standhousehold cleaning solution. Never use solvents or abrasive or corrosive compounds on the rame. Te base shouldcleaned at regular intervals to remove dust and dirt, and inspected or mechanical damage, wear and breaks - worn oparts should be replaced.

CLEANING THE TABLE TOP: All TermoDesk table tops are manuactured with a “3D lamination” process that resuin an extremely durable surace, similar to what is ofen used in hospital environments. As such it can stand up to mocleaning solutions without risk o discoloration or degradation. Anti-bacterial solutions may be used. Always test ncleaning solutions on a less-seen surace first beore using on the entire table top.

TROUBLESHOOTINGIF one side o the Omega Denali is rising up or down but not the other, check that the drive shaf is connected to bolegs.



SPECIFICATIONS

DYNAMIC WEIGHT CAPACITY:

STATIC WEIGHT CAPACTIY:

HEIGHT ADJUSTMENT RANGE:

WIDTH ADJUSTMENT RANGE:

200 lbs.

From 29-¼” to 48-¾”

From 32-½” to 54”

390 lbs.

TRAVEL SPEED:

ADJUSTABLE:

MANUFACTURING ORIGIN:

1 inch per 3 cranks

Manual Crank

Made in China

LAMINATION TYPE:

AVAILABLE SIZES:

Sur(x) 3D

30”x42” | 30”x48” | 30”x60” | 30”x72”

EDGING:

SURFACE RATING:

MANUFACTURING ORIGIN:

Ultra-durable

Ergonomically-contoured “comort edge”

Made in Michigan, USA

C O N T A C T : iMovR

HOURS:PHONE:FAX:EMAIL:LIVE CHAT:

See www.iMovr.com/hours(888) 208-6770 or (425) 999-3550(425) [email protected]

AVAILABLE OPTIONS FROM iMovR

Stowaway Ergonomic Keyboard ray

Single and Dual-Arm LCD Monitor Stands

Grommet-mounted Dual-AC Power Socket

DENALI Base

DENALI Table Top

2

1

3

1

2

3

Documents

Omega Denali Manual