Operating performance in any severe environmentswindrockgroup.com/portals/0/images/PDF/DID_Introduction.pdf · operating performance in any severe environments; ... still can make

1

Built to take it and proven to meet the Mil-Specs and satisfied theoperating performance in any severe environments; if the lens isobstructed by mud, snow, rain, etc., the T3 remains fully operational.Even in such extreme cases where the lens is shattered, the T3 is fullyfunctional as long as the shooter can see through any portion of the lens,the entire reticle pattern (dot) is visible on target.

Our product (Model T3) has been proven the physical endurance by the Defense Quality Assurance Agency objectively.7,000 rounds of live bullet were fired for testing had been performed and there is no defect whatsoever occurred andremain the same condition of product as new. For 25meters shooting, all the bullets hit the target within the 1inch circle and remain the same after the shooting.

Testing the operational capability of dot sight after 6 hours of - 51 in low temperature chamber.

Testing the operational capability of dot sight in -51 which isa lot worse than the normal standard temperature of -33 .

The photos after right out of low temperature chamber

A view from the shooter.(3/4 of lens are covered with mud andstill can make a accurate sighting.)

It was possible that our product isbuilt to support the 2 tons weightand remains the same with only asmall scratch.

Operating performance in any severe environments

Physical Endurance

Test for low temperature

2

Red dot Circle dot T- dot Special dot

3

Model DCL100 Dot SightModel DCL100 Red Dot Sight is designed and built specifically for Light/Multi Machine Guns such as M249 / M240GPMGs (General Purpose Machine Guns) (5.56 mm / 7.62 mm) and their variants which are utilized as a SquadAutomatic Weapon (SAW). This sight is developed to adapt the open dot sight system for wider field of view andconstructed to be used eliminating the conventional aiming method with iron sights for the line of sight and to makespeedy accurate shooting. The unique square lens provides wider view for the gunners. With both eyes open, theshooters acknowledge the surroundings. This sight is constructed for compactness, ruggedness and allows maximumutility of the instrument. Model DCL100 has built-in trajectory compensation device of 200, 300, 400, 500, 600 and 800meters.

UNIQUE FEATURES OF MODEL DCL100 DOT SIGHT FOR GPMG

No centering required as long as the red dot is on the targetBuilt for ruggedness of machine guns and deliver rock-solid stabilityAiming with both eyes open for tracking down the moving targets and surveying their surroundings Compatible with every generation of night vision devicesThe wide 45 X 30 mm square lens provides the wider field of viewTrajectory compensation device of 200, 300, 400, 500, 600 and 800 metersSave the ammunitions, decrease the training time and increase the target impactCan be utilized on the small firearms also (5.56 mm / 7.62 mm)Applicable to M249, K3, M240, M60 GPMGs

Specialized Dot Sight for

Light Machine Guns

4

Technical Specifications (Model DCL100 Dot Sight)

Specification may change without notice.

Optical Data

System Reflex, Collimator System

Magnification No Magnification (1X)

Eye Relief Unlimited

Red Dot Size 3 MOA Circle Dot

Field of View (FOV) 64.6 m @ 200 m

Objective Lens 45 30 mm

Optical Coating Anti Reflex Coating All Surfaces, Multi-layer Coating for Reflection of Red Light

Electronic Data

Battery One CR 123 A 3 V Lithium Battery

Battery Life 700 hours

Dot Brightness Settings 1 Off & 5 Daylight Mode, 3 Twilight Mode, 3 Nightvision Mode

Mechanical Data

Housing Material High Strength Aluminum

Surface Finish Hard Anodized, Matte, Black

Mounting Solution Built-in Type (For MIL STD 1913 Picatinny Rail)

Click Adjustment 1 click = 40 mm at 200 m

200, 300, 400, 500, 600, 800 meters (5.56 mm Caliber Machine Gun)

200, 400, 500, 600, 700, 800, 900, 1,000 meters (7.62 mm Caliber Machine Gun)

Dimensions

Length / Width / Height 180 mm / 90 mm / 75 mm

Weight 500 g

Environmental Data

Temperature Range -41 °C ~ +71 °C

Trajectory Ranges

5

Model DCL110 Dot SightModel DCL110 Dot Sight is designed and developed to be applicable to the improved and upgraded machine gunssuch as M240D and M134D MINIGUN which have a Spade Grip Device with buffer for being utilized for the armoredvehicles, tank, helicopter and patrol boats. Model DCL110 is also applicable to 12.7 mm (.50) caliber HMGs (M2HB,K6) and 20 mm cannon machine gun. The wide square lens (80 x 50 mm) allows operator aiming the target with botheyes open and provide a wide stable sight. Built-in trajectory compensator allows operator obtain accurate sighting byranges with a simple touch.

UNIQUE FEATURES OF MODEL DCL110 DOT SIGHT

The aiming is completed when the target is on dot (No centering required).Deliver rock-solid stability for repeatable accuracy on the machine guns with platforms on tank,or in helicopter.Makes easy for operator to aim the fixed and moving targets with both eyes open.No need to realign the line of sight after a shooting. Excellent adaptability of application on various type of machine guns. Compatible with every generation of NVD.Wide lens (80 x 50 mm) makes it easy to acknowledge the surroundings and tracking the targets.Deliver total eight (8) sets of trajectory compensation for 12.7 mm caliber machine gun : (200, 400,500, 600, 700, 800, 1,000 and 1,200 meters) and eight (8) sets for 7.62 mm caliber machine guns:(200, 400, 500, 600, 700, 800, 900 and 1,000 meters) and six (6) sets for 20 mm cannon guns :(500, 1,000, 1,500, 2,000, 2,500 and 3,000 meters)Reduce the training time, increase the shooting capability and save expensive ammunitions.


General Purpose Machine Guns

6

Technical Specifications (Model DCL110 Dot Sight)Optical Data





Field of View (FOV) 80 m @ 200 m



Electronic Data




Mechanical Data





200, 400, 500, 600, 700, 800, 1,000, 1,200 meters (12.7 mm Caliber Heavy Machine Gun)

200, 400, 500, 600, 700, 800, 900, 1,000 meters (7.62 mm Caliber Machine Gun)

500, 1,000, 1,500, 2,000, 2,500, 3,000 meters (20 mm Cannon Machine Gun)

Dimensions


Weight 1,300 g

Environmental Data


Trajectory Ranges


7

Model DCL120 Dot SightModel DCL120 is designed and developed primarily for the application of .50 (12.7 mm) Caliber Heavy Machine Guns(HMGs). This high performance Red Dot Reflex Sight is for demanding applications for the armed forces in Air(Helicopters), at Sea (Patrol Boats) and on Land (Armored Vehicles). It is built for speedy aiming and this highperformance red dot sight will take your shooting ability to the next level. The unique heads-up-display design withextra wide lens provides an unlimited field of view with both eyes open, while eliminating obstruction and tunnel visioncommon to tube style scopes. Enhance the capability of operator's confidence in the field.

UNIQUE FEATURES OF MODEL DCL120 RED DOT SIGHT FOR HMGS

Extra wide field of view for heads-up-display and faster target acquisitionEase to adjust the bullet drop compensation by ranges of 200, 400, 600, 800 and 1200 meters and can beoperated by both tactile and visual.Can do the sighting easily in jolting armored vehicles, rocking patrol boats and shaking helicoptersAiming with both eyes open for tracking down the moving targets and surveying operator's surroundingsEven the user's head moves up and down (70 mm) and sides (340 mm), the target is focused as long as thedot is on lens.Deliver rock-solid stability for repeatable accuracyNo centering requiredCompatible with every generation of night vision devicesReduce the training time and save ammunitions


Heavy Machine Guns

8








Anti Reflex Coating All Surfaces,

Multi-layer Coating for Reflection of Red Light

Electronic Data

Battery One CR 123 A 3 V Lithium Battery, or

External Power Source : 10 ~ 28 V (Option)

Battery Life 1,000 hours


Mechanical Data


Surface Finish Anodized, Matte, Carbon Black

Lens Cover Filter Polarizing Filter



Trajectory Ranges 200, 400, 600, 800, 1,200 meters

Dimensions


Weight 3,000 g

Environmental Data

Temperature Range -41 °C~ +71 °C Specification may change without notice.* MOA (Minute of Angle) 1 MOA = 30 mm at 100 m

Optical Coating

Model DCL401 Dot SightModel DCL401 Dot Sight is designed and developed primarily for the application of 40 mm Caliber Automatic GrenadeLauncher (AGL) such model as MK19 and K4 and designed and built for the fixed and moving targets in sea and onland (Armored Vehicles, Patrol Boats). The unique heads-up-display design with extra wide lens (80 x 50 mm)provides an unlimited field of view with both eyes open, while eliminating obstruction and tunnel vision common to tubestyle scopes. This Dot Sight comes with the tailored mount which has new type of bullet drop compensation systemtogether with the sight and will take your shooting ability to the next level. This Dot Sight will enhance the capability ofoperator's confidence in the field.

UNIQUE FEATURES OF MODEL DCL401 DOT SIGHT FOR AGL

Aiming will be completed when the red dot and target aligned. (No centering is required).Designed for the ruggedness for AGL and keep the accuracy with repeated shooting.Makes easy for the shooter to aim the fixed and moving targets with both eyes open.Deliver rock-solid stability for repeatable accuracy.Compatible with every generation of night vision devices.Extra wide lens (80 x 50 mm) makes it easy to acknowledge the surroundings and tracking the targets.Deliver total 12 sets of bullet drop compensation of 200, 400, 600, 700, 800, 900, 1,000, 1,100,1,200, 1,300, 1,400, and 1,500 metersReduce the training time and increase the shooting capability and save expensive ammunitions


Automatic Grenade Launcher(MK19)

9










Electronic Data

Battery CR 123A 3V Lithium Battery 1 EA



Mechanical Data


Surface Finish Anodized, Matte, Black

Mounting Solution Tailored Mounting System for MK19 AGL


Trajectory Ranges 200, 400, 600, 700, 800, 900, 1,000, 1,100, 1,200, 1,300, 1,400, 1,500 meters

Dimensions


Weight 4,500 g (with Mounting System)

Environmental Data


Specification may change without notice.* MOA (Minute of Angle) 1 MOA = 30 mm at 100 m

Optical Coating

10

11

Mounted on UMP with Model ODL 2

Model ODL2 Dot SightModel ODL2 Red Dot Sight is designed and built specifically for SWAT and SEAL forces operating in both indoor andoutdoor of urban districts for close quarters battle. This sight is adapted the open dot sight system for wider field ofview and constructed in one-piece frame for the ruggedness and integrated and combined with dual laser beamstogether for compactness and maximum utility of the instrument. The lasers are - one visible laser pointer formaximum daytime visibility and another invisible infrared laser pointer for the compatibility of every generations ofNVDs for various encountered situations.

UNIQUE FEATURES OF MODEL ODL2

Built in one-piece together with visible and invisible IR pointersUnlimited field of viewCompatible with every generation of NVD on invisible laserA positive rotary switch for the combined intensity of red dot and on / offswitch for lasersAll functions are powered by a single battery. Comes with the foregrip that contains the power source - batteryControl switch on foregrip allows easy adjustmentCan be utilized as a target indicatorBuilt for ruggedness and ensure the positive functionWaterproof and Fogproof

Professional

Dot Sight for SWAT

Technical Specifications (Model ODL2 Dot Sight)Optical Data

System Parallax Free, Reflex, Collimator System


Eye Relief Unlimited, No centering required



Objective Lens 28.3 mm



Electronic Data


Battery Life 700 hours for red dot only / 5 hours for continuous use of laser


Mechanical Data


Surface Finish Hard Anodized, Matte


Click Adjustment 1 click = 24 mm at 100 m (For red dot only)

Dimensions


Weight 640 g (with Perpendicular Foregrip)

Environmental Data


Laser Data Visible pointer IR pointer

Power Output 30 mW 30 mW

Wavelength 650 nm 850 nm

300 meters (low light) /

25 meters daytime

Laser Class b b

Beam Diameter 8 mm @ 25 m 8 mm @ 25 m

12

Optical Coating

Over 2 kmRange* / Visibility

Specification may change without notice.* Range may vary depending on light conditions.

Model T3IRL Dot SightThe Model T3IRL is born and designed and built with the concept of day/night time shooting. So far the dot sight hasbeen considered as a substitution for the front and rear iron sights on rifles. Now, our dot sight is fully integrated withInfrared (IR) Laser system and enhance the capability of night-time shootings and also can be used as a targetindicator. It has also its windage and elevation adjustment switches separately for laser zeroing.

Model T3IRL can be compatible with nightvision and provide the free parallax.

Shooter’s view of image

The third shooter’s view of image

UNIQUE FEATURES OF MODEL T3IRL

Available various sizes of dot (2 MOA, 3 MOA and 5 MOA)Compatible with every generation of night vision deviceUnlimited field of viewPush button switch instantaneously change the laser on and off withouta shift in the point of impactReduce the size and weight tremendously comparing the otherseparately equipped laser sightsCan be utilized as a target indicatorLong range of laser bean distanceWaterproof and Fogproof

13

Specialized

Military Dot Sight

14

Technical Specifications (Model T3IRL Dot Sight)Optical Data




Red Dot Size 2 MOA, 3 MOA, 5 MOA


Objective Lens 32 mm


Electronic Data

Battery One CR 123A 3V Lithium Battery



Mechanical Data





Dimensions


Weight 645 g (with Mount)

Environmental Data

Temp. Range -41 ~ +71

IR Laser Data

Laser Power 30 mW

Wavelength 850 nm

Beam Distance Over 2 km

14


Model T3 Dot Sight The Model T3 is specifically designed and built for the tactical application of Military and Law Enforcements for rapidtarget acquisition with accuracy for close-quarters combat. And it is also designed and built in single-piece forruggedness and durability with mounting base. It is built to be utilized in the underwater operation with superiorwaterproof as well as mountainous region in severe conditions. It is manufactured to withstand the external impact andmaintain the its functional capability of aiming. To prevent the operational delay due to equipment, it is built for rapidoperational accomplishment.

Mounted on M4 with Model T3

UNIQUE FEATURES OF MODEL MODEL T3

Compatible with every generation of night vision deviceUnlimited field of viewUnaffected by extremely severe weather conditionsPositive mechanical switch for speed and reliabilityIncrease the aiming confidenceReduce training time and save ammunitionsComes with mounting base together in one-pieceWaterproof and Fogproof

15

Specialized

Military Dot Sight

Technical Specifications (Model T3 Dot Sight)


Optical Data




Red Dot Size 2 MOA, 3 MOA, 5 MOA




Electronic Data

Battery One CR 123A 3V Lithium Battery



Mechanical Data





Dimensions



Environmental Data


16

17

Model DT323 Dot SightMinimized the weight by eliminating unnecessary portion and compacted the size with simple design. Fits to all MILSTD 1913 Picatinny Rail System. Compatible with every generation of night vision devices. Various mounts could beutilized with 30 mm size rings. Flip-up rubber covers not only protect the lens from the dust and sand but alsocamouflage the reflection of lens for use in the desert and jungle. Our rotary mechanical switch gives you positivesetting. The quality of our sights is our primary concern.

Mounted on M4 with Model DT323

UNIQUE FEATURES OF MODEL DT323

Available various sizes of dot from 3 MOA to 6 MOAUnlimited field of viewReliable and positive mechanical rotary switchFlip-up lens covers for protection from sand and dustCompatible with every generation of NVDRugged and durable constructionWaterproof and Fogproof

Specialized

Military Dot Sight

Technical Specifications (Model DT323 Dot Sight)


Optical Data




Red Dot Size 3 MOA, 6 MOA




Electronic Data

Battery One CR 2032 3V Lithium Battery



Mechanical Data


Surface Finish Hard Anodized, Matte, Carbon Black

Lens Covers Material Thermoplastic Elastomer, Black Non-Glare

Mounting Solution For MIL STD 1913 Picatinny Rail (1 Ring 30 mm )


Dimensions



Environmental Data


18

Documents

Operating performance in any severe environmentswindrockgroup.com/portals/0/images/PDF/DID_Introduction.pdf · operating performance in any severe environments; ... still can make