Click here to load reader
Upload
vuongtram
View
212
Download
0
Embed Size (px)
Citation preview
Asset Number: WS38-11
Performance SheetDrill Pipe4.750'' x 2.688'' XT38
4.000'' 14.00 ppf 0.330'' wall IU
Grade: S-135
Range: 2
Size and Weight:
Tool Joint:
Pipe Body:
OD (in):
Wall Thickness (in):
Nominal ID (in):
Nominal100% RBW 95% RBW
Ultra Class90% RBW
Premium80% RBW
Tensile Strength (lbs):
Torsional Strength (ft-lbs):
Burst Capacity (psi):
Collapse Capacity (psi):
4.000
0.330
3.340
41,918
20,141
3.967
0.314
3.340
485,769
39,586
21,161
18,604
3.934
0.297
3.340
458,124
37,281
20,048
17,042
3.868
0.264
3.340
403,526
32,752
17,820
13,836
Connection: XT38
TJ OD (in): 4.750
MYS (ksi): 120 Maximum MUT (ft-lbs): 16,600
Tool Joint Torsional Strength (ft-lbs): 27,600
Tool Joint Tensile Strength (lbs): 532,400
TJ ID (in): 2.688
Tubular Assembly:
Adjusted Weight (lbs/ft): 16.22
Approximate Length (ft): 32.0
Max Upset OD (in): 4.188
18
Pin TJ Length (in): 12
Box TJ Length (in): 17
Elevator Shoulder:
Smooth Edge OD (in): 4.938
Nominal TJ OD (in): 4.750
Notes: Body properties are calculated based on uniform OD and wall thickness.Burst capacity for Nominal (100% RBW) based on 87.5% RBW per API.
Fluid Capacity w/IPC (gal/ft): 0.43
19,491
Smooth Edge Height (in): 3/32
SE Elevator Shoulder Capacity (lbs): 523,100Tension at Connection Yield @ Max MUT (lbs): 428,500
Tension at Shoulder Separation @ Max MUT (lbs): Tensile Limited
Tension at Connection Yield @ Min MUT (lbs): 532,400
Tension at Shoulder Separation @ Min MUT (lbs): 531,200
N/A
N/A
Drift Size (in): 2.563
0
Note: These are OEM values that may vary with actual values due to mill tolerances, IPC tolerances, OEM rounding, and other factors. Pipe is purchased at a guaranteed 95% RBW. IPC is applied to a nominal thickness of 0.009''. Pipe will have an ID of 3.285'', which is smaller than pipe purchased at 87.5%.
Note: MUT values are based on a friction factor of 1.0. There is no published pressure rating for this connection.
Minimum MUT (ft-lbs): 13,900
Upset Type: IU Fluid Capacity w/o IPC (gal/ft): 0.43
Fluid Displacement (gal/ft): 0.25
4.281Assumed Elevator Bore (in):
366,000Nominal TJ OD Elevator Shoulder Capacity (lbs):
Note: Elevator capacity based on assumed elevator bore, no wear factor, and contact stress of 110, 100 psi. An increased elevator shoulder OD increases elevator capacity without affecting make-up torque.
XT38 is a trademark of NOV Grant-Prideco.
513,645
Fluid Displacement (bblsl/ft): 0.0059
Fluid Capacity w/IPC (bbls/ft): 0.0102
Fluid Capacity w/o IPC (bbls/ft): 0.0103
The technical information containted herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.workstringsinternational.com 08-Sep-15
Download the Workstrings International Pipe Specification App on the App Store℠ or Google Play™
Operational Limits of Drill Pipe
% Inspection Class80 4
XT38 4.750Connection
Pipe Body ODPipe Body
Tool Joint OD
0.330 S-135
120,0002.688 Tool Joint Specified Minimum Yield Strength
Wall Thickness Pipe Body Grade
Tool Joint ID
0
700
1,400
2,100
2,900
3,600
4,300
5,000
5,700
6,400
7,100
7,800
8,600
9,300
10,000
10,700
11,400
12,100
12,800
13,500
403,500
403,400
403,200
402,700
401,900
401,100
400,000
398,800
397,400
395,700
393,900
391,900
389,400
386,900
384,300
381,400
378,300
375,000
371,400
367,400
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
428,500
403,500
403,400
403,200
402,700
401,900
401,100
400,000
398,800
397,400
395,700
393,900
391,900
389,400
386,900
384,300
381,400
378,300
375,000
371,400
367,400
0
600
1,100
1,700
2,300
2,800
3,400
4,000
4,500
5,100
5,600
6,200
6,800
7,300
7,900
8,500
9,000
9,600
10,200
10,700
403,500
403,500
403,300
403,000
402,500
402,000
401,300
400,500
399,700
398,600
397,600
396,200
394,700
393,400
391,600
389,700
388,000
385,800
383,500
381,300
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
531,200
403,500
403,500
403,300
403,000
402,500
402,000
401,300
400,500
399,700
398,600
397,600
396,200
394,700
393,400
391,600
389,700
388,000
385,800
383,500
381,300
(in) (in)
(in) (in)
(psi)
(lbs)(ft-lbs) (lbs) (lbs) (ft-lbs) (lbs) (lbs) (lbs)
(ft-lbs) (ft-lbs)
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box ID’s, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
531,20013,900
14,200
14,500
14,800
15,100
15,400
15,700
16,000
16,300
16,600
522,000
510,300
498,600
487,000
475,300
463,600
451,900
440,200
428,500
(ft-lbs) (lbs)
06-17-2015
Make-up Torque RangeConnection